bissen21/Marlin_Firmware
1
0
Fork 0
Code Issues Pull Requests Projects Releases 4 Wiki Activity
15,365 Commits 1 Branch 4 Tags 151 MiB
e8dcbd8300
Commit Graph

1092 Commits

Author SHA1 Message Date
Scott Lahteine
8b8ad14178 Add Z_PROBE_LOW_POINT to prevent damage 2018-04-09 17:23:03 -05:00
Scott Lahteine
dca69efc11 Update Bed PID comments 2018-04-08 06:44:47 -05:00
etagle
a29adde5c0 Implement BEZIER_JERK_CONTROL 
Enable 6th-order jerk-controlled motion planning in real-time.
Only for 32bit MCUs. (AVR simply does not have enough processing power for this!)
 2018-04-07 21:03:28 -05:00
Lenbok
0e8242180d Chamber temperature monitoring and auto fan control. 
This is an initial cut for feedback, updated for 2.0.x.

Chamber temperature is currently reported along with hot end and bed
temperatures to serial. The format is just like that used for hot end
and bed temperatures, but using 'C' prefix. As there is no heater,
target is always 0. Is this appropriate, is there a better way to report
chamber temperatures?

Chamber temperatures are not reported on the LCD in any way.

When auto chamber fan is enabled, it currently just uses the same
temperature threshold as the other auto controlled fans.

As the chamber temperature is not connected to any heater, it doesn't
undergo mintemp/maxtemp monitoring. This would need to change in the
future if chamber heating became a feature.
 2018-04-06 23:09:06 -05:00
Scott Lahteine
adcb87f0db Z Endstop Servo => Z Probe Servo 2018-04-01 23:54:21 -05:00
Scott Lahteine
dd2949922b Consolidate 3-point leveling point options 2018-03-19 04:12:20 -05:00
Scott Lahteine
c6ff39cc14 Spacing cleanup 2018-03-17 16:49:08 -05:00
Scott Lahteine
14c03cb6f4
[2.0.x] Make MIN_PROBE_EDGE a general option (for electronic probes) (#10069) 
Some probes don't work near the edges of the bed. This change promotes MIN_PROBE_EDGE to a general setting that applies to all probing functions.
 2018-03-13 01:15:22 -05:00
Scott Lahteine
28f1276286
[2.0.x] Add Z_AFTER_PROBING option (#10058) 
Some "fix-mounted" probes need manual stowing. And after probing some may prefer to raise or lower the nozzle. This restores an old option but tailors it to allow raise or lower as preferred.
 2018-03-11 13:07:55 -05:00
Scott Lahteine
419d12ca1b Add UNKNOWN_Z_NO_RAISE option 
With this option enabled, Z won't ever be raised until after `G28` has been completed, and it won't raise if Z becomes unknown. This is good for machines whose beds fall when Z is powered off.
 2018-03-10 00:17:34 -06:00
Scott Lahteine
a2a672449a Updated boot screen description 2018-03-03 20:04:17 -06:00
Scott Lahteine
4953fb1c88 Standardize encoder defaults 2018-02-24 22:34:45 -06:00
Scott Lahteine
5684beae90 Bring some configs up to speed 2018-02-24 21:56:27 -06:00
Scott Lahteine
2024775e07
Spanish (UTF8) Language (#9786) 
From #7314 by @MrAmericanMike
 2018-02-23 20:24:02 -06:00
Scott Lahteine
b2cf253a13 Add RESTORE_LEVELING_AFTER_G28 option 2018-02-23 13:38:54 -06:00
Marcio Teixeira
13176dfe2f Merge remote-tracking branch 'origin/pr-lite-st7920-status' into pr-lite-st7920-status 2018-02-22 08:02:31 -07:00
Marcio Teixeira
716a22498f Changed temp type from uint8_t to int16_t 
- Also deleted old implementation files which had been renamed.
 2018-02-21 10:15:55 -07:00
Scott Lahteine
7d8c6b3f3c
Add 20x4 option for Sainsmart LCD (#9740) 2018-02-21 00:46:25 -06:00
Marcio Teixeira
aada1e698f Removed unused configuration options. 2018-02-19 16:14:33 -07:00
Marcio Teixeira
c7513eb032 Merge branch 'pr-lite-st7920-status' of github.com:marcio-ao/Marlin into pr-lite-st7920-status 2018-02-19 15:38:13 -07:00
Studiodyne
d3ca82d8c2 Support for multiple filament runout sensors 2018-02-19 07:02:50 -06:00
Scott Lahteine
ca55f2927a
Pulldown pin mode support (#9701) 
Implemented for LPC1768.
 2018-02-18 19:26:23 -06:00
Scott Lahteine
79272f98fc Proposed changes to ST7920 lightweight status screen 2018-02-18 02:47:31 -06:00
Marcio Teixeira
24eb275b99 Added a light-weight status screen for the ST7920 
- The status screen uses the ST7920 character generator to greatly
  reduce SPI traffic and MCU load when updating the status screen.

- Has been tested with the RepRapDiscount Full Graphics Smart Controller
  but should work with any LCD that uses an ST7920 or fully compatible
  controller.
 2018-02-18 02:29:45 -06:00
Scott Lahteine
08d685c97a Followup to 21e60fd 2018-02-16 02:09:17 -06:00
Roxy-3D
21e60fd3ed
Allow user to control Z-Height correction for off mesh movements (#9661) 2018-02-15 15:07:42 -06:00
Marcio Teixeira
4880ac6533 Added a light-weight status screen for the ST7920 
- The status screen uses the ST7920 character generator to greatly
  reduce SPI traffic and MCU load when updating the status screen.

- Has been tested with the RepRapDiscount Full Graphics Smart Controller
  but should work with any LCD that uses an ST7920 or fully compatible
  controller.
 2018-02-14 14:43:54 -07:00
Scott Lahteine
2ec65051fd Fix serial comment sp. 2018-02-13 22:40:56 -06:00
Scott Lahteine
2014d38e10 NEOPIXEL_BRIGHTNESS parity 2018-02-08 18:55:19 -06:00
Scott Lahteine
b5e92f4f90
[2.0.x] Enable / disable PSU automatically (#9503) 2018-02-06 00:22:30 -06:00
Scott Lahteine
16739264d3 Add UltiController v2.1 support 
Add compatibility with the original screen bord from Ultimaker 2 printer (UltiController v2.1 with the PG-2864ALBP I2C display)
 2018-02-05 22:30:03 -06:00
Scott Lahteine
4925f60cff Add MALYAN_LCD to configs 2018-02-04 18:52:44 -06:00
Scott Lahteine
7d6c009104 Add thermistor 15 tuned for JGAurora A5 2018-01-22 01:27:11 -06:00
Scott Lahteine
348b454401 Probe bounds based on bed size 2018-01-22 01:05:11 -06:00
Scott Lahteine
58ed9901d7 Consistent NEOPIXEL_TYPE options 2018-01-21 17:19:38 -06:00
Scott Lahteine
fa432508b0 Followup to Ender config 2018-01-15 06:00:21 -06:00
Scott Lahteine
048486390e Bring some configs up to date 2018-01-11 01:10:17 -06:00
Thomas Moore
f7efac57b7 Multi-host support 2018-01-10 00:14:47 -06:00
GMagician
5295b4713d [2.0.x] add semitec 104NT-4 (#9119) 
Table is very very similar to old 104-GT2 so I added only the name and recycled old ID
 2018-01-09 16:53:12 -06:00
Scott Lahteine
0b4a46fa6c Bring configs up to date with 1.1.x 2017-12-30 23:28:53 -06:00
Thomas Moore
f0a8a1a853 [2.0.x] Use NOZZLE_PARK_FEATURE for ADVANCED_PAUSE_FEATURE (#8866) 
* Use NOZZLE_PARK_FEATURE for ADVANCED_PAUSE_FEATURE
 2017-12-25 01:38:06 -06:00
Scott Lahteine
28fc8741d6 Reduce default jerk. XY by half. Z by 1/4 2017-12-24 19:54:11 -06:00
Even
ea1a8d1223 add original RADDS LCD + Controller 
adds setup for the original Radds Display+Controller+SD Card Reader PCB
http://doku.radds.org/dokumentation/lcd-display/
 2017-12-24 19:00:23 -06:00
Dan Delaney
b055d8c39c [2.0.x] Adding support for using the MKS_12864OLED with the SSD1306 controller (#8814) 
* Adding support for using the MKS_12864OLED with the SSD1306 controller

* Update comment for correct controller type
 2017-12-16 18:47:04 -06:00
Scott Lahteine
15d05748df Adding support for the Tronxy and Zonestar LCD 2017-12-15 19:13:52 -06:00
Scott Lahteine
69d49a2438 Shorter segments may be better 2017-12-09 06:29:14 -06:00
Scott Lahteine
ae663a4198 PROBE_DOUBLE_TOUCH => MULTIPLE_PROBING 2017-12-07 16:44:13 -06:00
Richard Wackerbarth
c1184552ac Change K1 to required option PID_K1 2017-12-05 19:59:59 -06:00
Scott Lahteine
aa7efb96bf Bring configurations up to date 2017-12-02 21:50:51 -06:00
Scott Lahteine
0154e3480c New feature: BED_SKEW_CORRECTION 2017-12-01 19:39:49 -06:00
Scott Lahteine
ef2531558c Add an option to segment leveled moves 2017-11-29 16:57:30 -06:00
Scott Lahteine
5926c9c97b Followup for MESH_EDIT_GFX_OVERLAY 2017-11-24 15:53:25 -06:00
Scott Lahteine
5ce7f23afa Config option G26_MESH_VALIDATION for all meshes 2017-11-23 21:43:23 -06:00
Scott Lahteine
3f0a982b8c Move Filament Width Sensor to Configuration_adv.h 2017-11-13 21:05:57 -06:00
Scott Lahteine
b76e173205 Move test extrusion options under G26 2017-11-13 21:05:57 -06:00
Scott Lahteine
81b91b3f9d Clean up some trailing white-space 2017-11-10 02:31:04 -06:00
Roxy-3D
967104e1ce
Default Extrusion Settings were off a few lines in some of the example config files. (#8333) 2017-11-08 11:56:00 -06:00
Roxy-3D
ed62c621d7
Fix G26 Circle Drawing. Add Default Extrusion Settings (#8313) 
- Fix G26 Circle Drawing.
- Add default extrusion settings so machine can print lines on print bed
- Yet to be done: Get LCD Menu's to use these settings.
 2017-11-07 17:13:53 -06:00
Scott Lahteine
2c099fd4c2 Update Thermal Protection Documentation 2017-11-07 15:46:44 -06:00
Scott Lahteine
d83a9a53e8
Merge pull request #8220 from thinkyhead/bf2_serial_port_-1 
[2.0] Add SERIAL_PORT -1 option for configurators
 2017-11-03 15:25:12 -05:00
Scott Lahteine
93ba72ea83 Add SERIAL_PORT -1, set on SBASE, STM32F103RET6 2017-11-03 15:22:45 -05:00
Scott Lahteine
7e43dd1d23 Fix probes configuration url 
Based on #8241 by @machaj
 2017-11-03 13:35:40 -05:00
android444
9cc1d8e312 [2.0.x] Support for SilverGate Board 2017-10-31 15:27:26 -05:00
Scott Lahteine
34be5d33c0 The plural of 'axis' is 'axes' 2017-10-30 14:21:43 -05:00
Scott Lahteine
7fad26549b Concise SD_REPRINT_LAST_SELECTED_FILE description 2017-10-26 23:33:02 -05:00
Scott Lahteine
46e9eae159 Tweak to M100 config comment 2017-10-26 17:25:44 -05:00
Scott Lahteine
7f55d82fd1 Move UBL_SAVE_ACTIVE_ON_M500 to Configuration.h 2017-10-24 18:26:43 -05:00
Scott Lahteine
580b6e9089 Apply physical limits to mesh bounds 2017-10-24 16:54:07 -05:00
Scott Lahteine
5f87324536 Fix some config verbiage 2017-10-24 14:53:42 -05:00
cdedwards
6296ab2173 Add GFX overlay to UBL mesh edit (#8038) 
* Add GFX overlay to UBL mesh edit

Fixed misplaced HAS_TEMP_BED in dogm_bitmaps.h

rename _lcd_babystep_zoffset_overlay to _lcd_zoffset_overlay_gfx and move it out of BABYSTEP_ZPROBE_OFFSET to we can use it for over things. Add this function into UBL mesh edit screen.

update all Configuration.h to add ENABLE_MESH_EDIT_GFX_OVERLAY

* Add Sanity to UBL  insanity

Need to check for DOGLCD  otherwise error out.
 2017-10-24 14:14:03 -05:00
Roxy-3D
572cf0ec95 UBL able to generate mesh and save and load it on 32-bit platforms (#8015) 
* Get UBL Mesh Generation, Mesh Save & Mesh Load working with 32-Bit platforms

* clean up read_data() and write_data() for non-LPC1768 HAL's

* Get read_data() and write_data() return codes consistent

All HAL's read_data() and write_data() return false if they succeed.

* Get read_data() and write_data() return codes to be consistent

Make read_data() and write_data() return true if an error happens.

* Say UBL is now checked out on machine types in default Configuration.h file.
 2017-10-18 14:00:29 -05:00
Jeffrey Li
eeb4611606 Add proper support for the AZSMZ 12864 LCD on a SMART RAMPS 2017-10-16 00:33:07 -07:00
Scott Lahteine
014a83fe09 Merge pull request #7984 from thinkyhead/bf2_micromake_c1 
[2.0.x] Micromake C1 Configurations, Unaccented French
 2017-10-14 21:19:32 -05:00
Scott Lahteine
34a261416f Add unaccented French language 2017-10-14 20:28:12 -05:00
Jeff Eberl
b206f70693 Split the software endstop capability by axis. 2017-10-14 18:44:20 -05:00
Slawomir Ciunczyk
a11e6a1022 Different NEOPIXEL types 
Same as #7728 but for 2.0.x,
Lot of cleanup and remove references in whole code to other "LED files" than leds.h. Now will be much easier to add next drivers/libraries. e.g. FastLED. But bad news, currently FastLED is suporting only RGB devices (no RGBW)
 2017-10-10 02:17:36 -05:00
Scott Lahteine
e9bcb9d048 Add 4 new LCD displays 2017-10-09 15:58:02 -05:00
Scott Lahteine
9fe7f53216 Misc general spacing cleanup 2017-10-06 15:14:01 -05:00
Scott Lahteine
508d764d63 Add serial XON/XOFF handshaking 
From @ejtagle, originally #7459
 2017-10-02 04:12:30 -05:00
Scott Lahteine
90af1fe5ee Implement NO_MOTION_BEFORE_HOMING option 2017-10-01 21:58:50 -05:00
Christopher Pepper
bea3ec2724 M355 S0, S1 fixes & faster LCD, SD card 
fix Travis error
 2017-09-27 19:26:00 -05:00
Scott Lahteine
7cd5eb6d42 Update LEVEL_BED_CORNERS config option 2017-09-27 00:48:59 -05:00
Scott Lahteine
4c5be9bb05 Fix a PARKING_EXTRUDER comment 2017-09-27 00:48:58 -05:00
Scott Lahteine
494b0eba2d Config spacing fix 2017-09-27 00:48:47 -05:00
Scott Lahteine
f37ed314e0 Friendly layout for Arduino IDE 2017-09-21 16:27:13 -05:00
Scott Lahteine
f536c4dccb Move configs 2017-09-06 06:28:30 -05:00
Scott Lahteine
e4fcf460e7 Marlin bugfix-2.0.x Version/README 2017-08-31 17:56:08 -05:00
Michal Holes
54d48130f3 Slovak UTF-8 translation 
Slovak UTF-8 translation
 2017-08-23 19:14:35 -05:00
Vben
4817b39d98 Added new feature for AutoParking Extruder (APE) 2017-08-16 17:33:11 -05:00
Scott Lahteine
385f1bb9e5 Merge pull request #7504 from thinkyhead/bf1_servo_delays 
Individual servo delays
 2017-08-16 16:05:22 -05:00
Scott Lahteine
a1878cd1c0 Add "Level Corners" menu option 2017-08-16 02:54:33 -05:00
GMagician
e9c72978c7 Implement SERVO_DELAY as array 
This modify give SERVO_DELAY x servo basis
 2017-08-15 00:28:47 -05:00
Jozsef Kiraly
97c21e9007 Support for Geeetech GT2560 Rev.A/Rev.A+ 2017-08-06 00:42:54 -05:00
Scott Lahteine
804818b4d9 Bring configs up to date 2017-08-05 03:48:52 -05:00
teemuatlut
936d00dda8 Implement probing delay for piezo sensors 2017-07-29 21:46:40 -05:00
Scott Lahteine
51864fd365 Add bed size as a configuration option 2017-07-26 23:04:54 -05:00
C. Scott Ananian
890e7a16a9 Add support for Printrbot Neopixel RGBW strip. 
Connected as described at http://printrbot.com/shop/led-strip/

Based on patch by Kelly Anderson <kelly@xilka.com> at
http://www.xilka.com/printrbot/marlin/1.1.4/20170707/
 2017-07-22 16:07:55 -05:00
Scott Lahteine
fc9ce65095 Add BUSY_WHILE_HEATING for hosts that need it 2017-07-06 16:28:57 -05:00
Petr Zahradník
8c34233452 UTF-8 mapper for Czech 2017-07-04 15:51:23 -05:00
Scott Lahteine
69297b2d7b Make all EEPROM optimization options available 2017-07-02 20:47:03 -05:00
Scott Lahteine
232a10410d LCD_FOR_MELZI 2017-07-01 22:32:20 -05:00
Scott Lahteine
dcec7178d1 Expose DISABLE_M503 option as a test option 2017-07-01 21:31:28 -05:00
Scott Lahteine
5b03f23fa2 Bring configurations up to date, fix some comments 2017-06-28 16:41:49 -05:00
Scott Lahteine
5b11b33854 Add support for Průša MK2 Multiplexer 2017-06-27 04:55:30 -05:00
Scott Lahteine
afbc6e3e2f Update DELTA/SCARA config comments 2017-06-24 12:47:17 -05:00
Bob-the-Kuhn
325f09ea6c Add link to custom LiquidCrystal library by F. Malpartida 2017-06-22 13:07:08 -05:00
Scott Lahteine
907cafcbfd Support for two switching extruders 2017-06-19 17:20:59 -05:00
dot-bob
0bc66bf22c PCA9632 PWM color LED support 
Add support for the PCA9632 PWM color LED driver used on the Ultimaker 2 and Wanhao Duplicator 6.
 2017-06-12 01:09:24 -05:00
Bob-the-Kuhn
1c107b3949 delete problem line 2017-06-09 11:53:36 -05:00
Scott Lahteine
e556ab1dff Find three-point leveling points on Delta 2017-06-07 16:07:38 -05:00
Scott Lahteine
1919cb0d1e Config cleanups 2017-06-01 19:26:16 -05:00
Roxy-3D
364f8fb613 Update Configuration.h files to better names (#6814) 
Changed UBL_G26_MESH_EDITING to UBL_G26_MESH_VALIDATION
Added UBL_MESH_EDIT_MOVES_Z to prepare for that change (coming next)
 2017-05-21 11:10:22 -05:00
Scott Lahteine
99c4900a98 SPINDLE/LASER config changes 2017-05-17 04:23:06 -05:00
fixoid
c2321b1cdd Separate SWITCHING_NOZZLE and SWITCHING_EXTRUDER 2017-05-16 19:25:17 -05:00
Scott Lahteine
1c4ed8b106 Note 5 extruders in config comments 2017-05-07 21:28:54 -05:00
Brian
faa270071d Improve BLTOUCH_HEATERS_OFF functionality 
- rename to PROBING_HEATERS_OFF
 - move heater pausing functionality into thermalManager
   - add variables, pause(), ispaused(), other functions
 - add fan pausing functionality -> PROBING_FANS_OFF
 - add probing_pause() wrapper
 - move pausing into do_homing_move() and do_probe_move() to minimize quiet time and so other probe types can benefit
 - example configs
 2017-05-07 16:22:08 -04:00
Scott Lahteine
77769e284f Edit configuration comments 2017-05-05 13:32:31 -05:00
Scott Lahteine
da08e11acd Add EXTRAPOLATE_BEYOND_GRID option to bilinear leveling 2017-05-04 00:19:07 -05:00
Scott Lahteine
54751e8557 Put DISTINCT_E_FACTORS adjacent to the affected settings 2017-04-30 15:30:31 -05:00
Scott Lahteine
0dbe4b3e54 Edit configurations to reduce verbosity, arrange logically 2017-04-30 15:30:31 -05:00
Scott Lahteine
d7d4378481 Remove inaccurate version description 2017-04-30 14:57:19 -05:00
Scott Lahteine
7db805930a Cleanup configurations 2017-04-28 18:32:39 -05:00
Roxy-3D
4075b95519 Allow BL-Touch users to control heaters during probe event (#6485) 
The Configuration.h file entries for BL-Touch have been updated to:
```cpp
//#define BLTOUCH
//#define BLTOUCH_DELAY 375      // (ms) Enable and increase if needed
//#define BLTOUCH_HEATERS_OFF // if defined the printer's heaters are
turned off during probe event
```
 2017-04-28 09:19:55 -05:00
Scott Lahteine
959566cf0a Update note about M163 / M164 2017-04-22 16:23:15 -05:00
Scott Lahteine
0e97b3d6d0 Fix some configuration spacing 2017-04-14 22:36:10 -05:00
Scott Lahteine
1bd25fd2b3 Clean up config spacing, section headings, etc. 2017-04-14 19:06:31 -05:00
Scott Lahteine
fd2a0784ba Add support for SOLENOID_PROBE 2017-04-14 17:24:36 -05:00
Scott Lahteine
dac21ec680 Add support for an RGBW LED 2017-04-11 12:58:55 -05:00
Scott Lahteine
e7746ffee4 Extend RGB LED support, adding Printer Events 2017-04-11 12:15:41 -05:00
Scott Lahteine
9343f6a95f Put TOSHIBA with other stepper driver options 2017-04-09 20:52:49 -05:00
Scott Lahteine
1855534f20 Config files cleanup 2017-04-09 06:44:52 -05:00
Scott Lahteine
c26a315d0b Additional missed patches 2017-04-09 04:24:23 -05:00
Scott Lahteine
c54f6cf23d Updates to support 5 extruders 2017-04-09 03:49:16 -05:00
Scott Lahteine
824f3c1c0d Fix up configuration comments 2017-04-08 18:59:56 -05:00
Scott Lahteine
995ed90248 Clean up Filament Width Sensor comments 2017-04-08 18:59:56 -05:00
Scott Lahteine
2a84122edd Configuration changes to support 5 extruders 2017-04-07 10:46:35 -05:00
Bob-the-Kuhn
3b8926bd09 improved wording, consolidation of info, BLTouch warning 
==============================================

clarified BLTouch calculation & changed comment delimitters/flags

I found it hard to pickout the various sections in this area so I
changed most comments from // style to /** ... */

Made the BLTouch calculation simpler and clarified the units of measure
for the result.

============================================

add changes to example configurations

============================================

add TinyBoy2 to this PR & add BLTouch Delay
 2017-04-06 16:06:01 -05:00
Scott Lahteine
d13991ae18 Use same config name for all mesh dimensions 2017-04-06 16:05:59 -05:00
Scott Lahteine
c56eec29f0 Configurable delay for BLTouch servo emulation 2017-04-02 11:14:53 -05:00
Scott Lahteine
9e22184936 Add a "manual" option for ABL 2017-03-31 11:50:18 -05:00
Scott Lahteine
81136c1e82 Merge pull request #6177 from thinkyhead/rc_tinyboy 
Support for TinyBoy 2 3D printer (and its OLED display)
 2017-03-31 04:31:47 -05:00
Stefan Brüns
0fe57ad4f5 Add Support TinyBoy2 OLED/Encoder panel 
The OLED is driven by an SSD1306, connected to the board via
I2C, the rotary encoder is connected to 3 GPIO pins.

Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
 2017-03-31 04:05:34 -05:00
Scott Lahteine
edbc024d76 Disable UBL_G26_MESH_EDITING by default 2017-03-31 02:20:20 -05:00
Scott Lahteine
5a2abeca78 Merge pull request #6100 from thinkyhead/rc_soft_pwm_dither 
Enhancement of PWM, with dithering
 2017-03-24 04:57:40 -05:00
Stefan Brüns
35a55d5757 SOFT_PWM: Implement dithering if SOFT_PWM_SCALE is 1 or more 
If dithering is enabled, the remainder of the soft_pwm_X duty value at
turnoff time is added to the next cycle. If e.g. the duty is set to 9 and
SCALE is set to 2, the PWM will be active for 8 counts for 3 cycles and
12 counts on each fourth cycle, i.e. the average is 9 cycles.

This compensates the resolution loss at higher scales and allows running
fans with SOFT_PWM with significantly reduced noise.

Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
 2017-03-24 04:13:36 -05:00
Scott Lahteine
783338a0b8 Add UBL_MESH_EDIT_ENABLED to configs 2017-03-24 00:44:55 -05:00
Scott Lahteine
e244399766 Additional cleanup of UBL code 2017-03-22 20:51:10 -05:00
Scott Lahteine
2512871a36 Patch configs UBL followup 2017-03-18 12:32:03 -05:00
Scott Lahteine
27b5666e15 Move Allen Key probe definition to the top 2017-03-18 12:27:37 -05:00
Scott Lahteine
cf94688925 Univeral Bed Leveling - configuration 2017-03-18 11:35:19 -05:00
Scott Lahteine
0e410c9dfd Software endstop options as simple switches 2017-03-17 06:05:17 -05:00
Scott Lahteine
3e927ff204 Replace MBL Z hacking 2017-03-17 06:05:17 -05:00
Marek Pikuła
6836b94eea Added circle pattern for nozzle cleaning feature 2017-03-06 03:03:00 -06:00
Colin Gilgenbach
48b7e0f8d8 Nozzle Wipe Vertical Zig-Zag 
- Add configuration support for zigzags in either the X or Y axis, for
wipe pads significantly longer in one dimension.
- Add configuration for default number of zig-zag triangles, vs. a
magic number in `Marlin_main.cpp`.
- Update description of auto nozzle wiping to match functionality
 2017-02-25 21:52:43 -06:00
Scott Lahteine
e282b72151 Remove non-applicable comment on MANUAL_Z_HOME_POS 2017-02-18 05:14:43 -06:00
esenapaj
d38e335272 From "microseconds" to "milliseconds" 
delay() is milliseconds
 2017-01-02 01:19:33 +09:00
Scott Lahteine
5ab7b91615 Comment on filament runout sensor config 2016-12-23 19:50:27 -08:00
Scott Lahteine
78d6d6e076 Merge pull request #5452 from thinkyhead/rc_save_your_mesh 
Save Bed Leveling to EEPROM
 2016-12-15 20:23:01 -08:00
Scott Lahteine
1b2fb2bdc7 ABL_GRID_POINTS_* => ABL_GRID_MAX_POINTS_* 2016-12-15 19:08:41 -08:00
esenapaj
069c6b38dd Remove unnecessary tabs and spaces 2016-12-16 00:21:32 +09:00
Scott Lahteine
da6a094424 Sanity-check inverting and pullups for Z probe and Z endstop 
`Z_MIN_ENDSTOP_INVERTING` must match `Z_MIN_PROBE_ENDSTOP_INVERTING`
when using `Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN`.
This is easy to overlook.
 2016-12-08 00:12:19 -08:00
Scott Lahteine
aa241c63b3 Include M205 note in configurations 2016-12-07 14:45:44 -06:00
akaJes
d7b948610a Experimental bilinear subdivision option 2016-12-05 20:11:24 -06:00
Scott Lahteine
3391c785c6 Support for distinct E factors 2016-12-05 07:26:18 -06:00
Scott Lahteine
415294801f Merge pull request #5330 from thinkyhead/rc_rgb_led 
Support for an RGB LED using 3 pins
 2016-11-30 14:14:00 -06:00
Scott Lahteine
65c50e062e Support for an RGB LED using 3 pins 2016-11-30 00:02:31 -06:00
jes
f674246397 extend Configurations files 2016-11-29 15:04:36 +02:00
Scott Lahteine
092e949b58 Merge pull request #5169 from thinkyhead/rc_core_inverted 
Support for COREYX, COREZX, COREZY
 2016-11-28 02:26:41 -06:00
Scott Lahteine
f6f77d34a1 Add a fade factor for mesh leveling 2016-11-26 03:41:26 -06:00
Scott Lahteine
eb714ee873 Move dummy thermistor opts, fix redundant sensor comment 2016-11-18 22:24:48 -06:00
Scott Lahteine
7a99c6ce4f Reformat temp sensor listing 2016-11-18 22:24:47 -06:00
Scott Lahteine
eb120e518c Followup to new endstop interrupts feature 
- Fix typos, verbiage
- Fix naming of `setup_endstop_interrupts`
- Some formatting, indentation, spacing
 2016-11-18 21:53:45 -06:00
Scott Lahteine
832fe284b4 Merge pull request #5184 from AnHardt/endstop_interrupts 
Introduce endstop interrupts
 2016-11-18 20:50:24 -06:00
Scott Lahteine
2330619da0 Merge pull request #5191 from petrzjunior/const 
Replace const bool with #define for consistency
 2016-11-17 03:37:32 -06:00
Petr Zahradník junior
d7ce5d271b
Replace const bool with #define for consistency 2016-11-16 18:55:21 +01:00
AnHardt
f3eee02596 Introduce endstop interrupts 
If ENDSTOP_INTERRUPTS_FEATURE is enabled this tries to set up interrupt routines
for all used endstop pins. If this worked without errors, `endstops.update()` is called
only if one of the endstops changed its state.

The new interrupt routines do not really check the endstops and react upon them. All what they
do, is to set a flag if it makes sense to call the endstop test we are used to.

This can be used on:
* ARM (DUE) based boards - all pins can raise interrupts,
* RAMPS - all 6 endstop pins plus some other on EXT-2 can raise interrupts,
* RAMPS based boards - as long the designers did not change the pins for the endstops or at least left enough,
* all boards, if there are enough pins that can raise interrupts, and you are willing/able to swap with pins dedicated to other purpose.
 2016-11-15 12:07:41 +01:00
esenapaj
2ae72b0491 Follow up the PR #5167 (Add Turkish Language) again, etc 
・Update forgotten K8400\Dual-head\Configuration.h
・Adjust spacing
 2016-11-09 06:31:21 +09:00
Scott Lahteine
e3c8318504 Add reversed CORE options 2016-11-05 23:47:46 -05:00
Rigid3D
2327764980 Add Turkish Language 2016-11-05 21:06:16 -05:00
Scott Lahteine
0908329d96 Merge pull request #5057 from thinkyhead/rc_mbl_lcd_logical 
Fix manual leveling coordinates
 2016-10-22 06:31:02 -05:00
Scott Lahteine
14e60f0d3b Correct typo in configs 
As pointed out by #5044
 2016-10-22 05:56:32 -05:00
Scott Lahteine
4f6bfabaad Patch BAUDRATE line in configs 2016-10-22 00:48:52 -05:00
Scott Lahteine
1e551c0688 Revert "Squashed - Removal of PID functional range" 2016-10-09 16:27:45 -05:00
Rerouter
5f5d87cad3 Update Configuration.h 2016-10-02 07:01:40 -05:00
Scott Lahteine
d19cfcfc1d max_jerk array, DEFAULT_XYJERK => DEFAULT_[XY]JERK 2016-10-02 06:34:56 -05:00
Scott Lahteine
473f4a17a8 Merge pull request #4914 from Rerouter/PID-Unconstrained-Itemp 
Pid unconstrained itemp
 2016-10-01 06:58:07 -05:00
Scott Lahteine
2d2c9bdf92 Add PROBE_Y_FIRST option for probe order 2016-09-29 02:00:27 -05:00
esenapaj
92c03a44a9 Fix the PR #4899 (ABL: Enable by type. Bilinear for all.) etc. 
About Configuration.h:
・Fix the PR #4899 (ABL: Enable by type. Bilinear for all.)
Remove Duplicated contents

・Fix the PR #4305 (Custom boot screen feature improvement)
Revert from "during boot" to "during bootup" in all the example
Configuration.h

・Fix the PR #4207 (Clean up, simplify and generalize the Allen-key-probe
code.)
Resolve and relocate the duplicated definitions in Z_PROBE_ALLEN_KEY
section

・Follow-up the PR #4805 (Additional documentation of Configuration.h)
Add forgotten changes to all the example Configuration.h

Adjust spacing

About Configuration_adv.h:
Add missing description of SLOWDOWN for DELTA

Adjust spacing
 2016-09-28 14:14:04 -05:00
Rerouter
50e5ee4de4 Update Configuration.h 2016-09-28 17:38:09 +10:00
Scott Lahteine
ea0dbee3c9 Enable ABL by type, support bilinear on cartesian 2016-09-25 23:35:37 -05:00
Scott Lahteine
01f1028510 Try on "CLEARANCE" for size 2016-09-20 18:29:49 -05:00
Scott Lahteine
0e7d638a7a Revert to Probe Raise rather than Probe Height 2016-09-20 18:29:49 -05:00
Scott Lahteine
e05af606a8 Clean up probe config options 2016-09-19 00:26:16 -05:00
Scott Lahteine
c4dcfa254e Allow override of Z_ENDSTOP_SERVO_NR with BLTOUCH 2016-09-18 22:00:32 -05:00
Scott Lahteine
e5505e3b33 Allow non-square leveling grid 2016-09-18 13:11:20 -05:00
Scott Lahteine
d4599fd8ed Comment patches to Configuration.h 2016-09-16 14:41:05 -05:00
Scott Lahteine
723e983073 Default EXTRUDE_MAXLENGTH to 200mm 2016-09-16 14:41:04 -05:00
Scott Lahteine
a6f6ed352b Fix comment on FILAMENT_RUNOUT_SENSOR 2016-09-13 02:14:34 -05:00
Scott Lahteine
aaef7c6b89 Fix a misspelling of minimum 2016-09-02 01:42:38 -05:00
Scott Lahteine
f1201e11c7 Improve the Jerk description 2016-08-29 12:39:21 -05:00
Scott Lahteine
3f038bef00 Heading for movement settings 2016-08-29 02:01:34 -05:00
Scott Lahteine
01d4703429 PREVENT_DANGEROUS_EXTRUDE => PREVENT_COLD_EXTRUSION 
Also improve the documentation of this and related options, and set
EXTRUDE_MINTEMP to 170 everywhere.
 2016-08-20 23:35:27 -05:00
Scott Lahteine
99b22d5785 Default AUTO_BED_LEVELING_GRID_POINTS to 3 2016-08-19 04:45:32 -05:00
Scott Lahteine
e113740fa3 Specify that Z_PROBE_*_HEIGHT is nozzle-relative 2016-08-07 17:54:17 -07:00
Scott Lahteine
7e2bd9a233 Z_RAISE_PROBE_* => Z_PROBE_*_HEIGHT 2016-08-03 21:18:38 -07:00
Scott Lahteine
9e21b2e51d Merge pull request #4455 from AnHardt/double-bump-feature 
double bump probing as a feature
 2016-07-29 20:00:10 -07:00
AnHardt
7188ce0ad6 double bump probing as a feature 
Why double touch probing is not a good thing.

It's widely believed we can get better __probing__ results when using a double touch when probing.

Let's compare to double touch __homing__.
Or better let's begin with single touch __homing__.
We home to find out out position, so our position is unknown.
To find the endstop we have to move into the direction of the endstop.
The maximum way we have to move is a bit longer than the axis length.
When we arrive at the endstop - when it triggers, the stepper pulses are stopped immediately.
It's a sudden stop. No smooth deacceleration is possible.
Depending on the speed and the moving mass we lose steps here.
Only if we approached slow enough (below jerk speed?) we will not lose steps.

Moving a complete axis length, that slow, takes for ever.
To speed up homing, we now make the first approach faster, get a guess about our position,
back up a bit and make a second slower approach to get a exact result without losing steps.

What we do in double touch probing is the same. But the difference here is:
a. we already know where we are
b. if the first approach is to fast we will lose steps here to.
But this time there is no second approach to set the position to 0. We are measuring only.
The lost steps are permanent until we home the next time.

So if you experienced permanently rising values in M48 you now know why. (Too fast, suddenly stopped, first approach)

What can we do to improve probing?
We can use the information about our current position.
We can make a really fast, but deaccelerated, move to a place we know it is a bit before the trigger point.
And then move the rest of the way really slow.
 2016-07-30 03:00:49 +02:00
Scott Lahteine
c31f56a38c Deprecate EXTRUDER_WATTS and BED_WATTS 2016-07-29 17:34:14 -07:00
Scott Lahteine
ea5ac94804 Improved MANUAL_[XYZ]_HOME_POS 
No need for `MANUAL_HOME_POSITIONS`. Just set each one as-needed to
override the automatic behavior.
 2016-07-28 19:51:48 -07:00
Scott Lahteine
8953e3e984 Allow Z_SAFE_HOMING without a probe 2016-07-27 04:33:56 -07:00
Scott Lahteine
24a1a16e5d Move versioning to MarlinConfig.h 2016-07-26 12:37:14 -07:00
Scott Lahteine
277899c175 Move include _Bootscreen.h where needed 2016-07-26 12:37:13 -07:00
Scott Lahteine
83c4653c71 Include boards and macros ahead of configs 2016-07-26 12:19:50 -07:00
Scott Lahteine
c6226bb0aa Unify config in a single include without nested includes 2016-07-25 23:04:19 -07:00
Scott Lahteine
2d378fac1b No need to include thermistortables.h in Configuration.h 2016-07-25 22:43:50 -07:00
Scott Lahteine
0c0a63322b Patches to prepare REPRAPWORLD_GRAPHICAL_LCD 2016-07-25 12:10:25 -07:00
brupje
a60a668f6b Support for REPRAPWORLD_GRAPHICAL_LCD 2016-07-25 12:10:25 -07:00
Scott Lahteine
bb9da6ebdd Document DEBUG_LEVELING_FEATURE 2016-07-22 23:37:41 -07:00
Scott Lahteine
194d9521c3 Merge pull request #4356 from thinkyhead/rc_simpler_run_z_probe 
Unify run_z_probe
 2016-07-19 19:02:39 -07:00
Scott Lahteine
4a6ed5e221 Use HOMING_FEEDRATE_Z for Z_PROBE_SPEED_FAST 2016-07-19 18:42:48 -07:00
AnHardt
09a3cc33e6 Unify run_z_probe 
Unify run_z_probe
Add double touch for DELTAs.
Introduce Z_PROBE_SPEED_FAST and Z_PROBE_SPEED_SLOW
  defaulting to homing_feedrate_mm_m[Z_AXIS] and homing_feedrate_mm_m[Z_AXIS]/2
 2016-07-19 18:42:48 -07:00
Scott Lahteine
e44b37cdc2 motion section marker below homing speeds 2016-07-19 17:31:58 -07:00
Scott Lahteine
204fd6ec44 Set homing feedrates individually 2016-07-19 17:31:58 -07:00
Scott Lahteine
6abf916575 Reprapworld Keypad move step is 1mm 2016-07-19 16:40:39 -07:00
João Brázio
47fef80848 Nozzle::clean() no longer requires HAS_BED_PROBE 2016-07-19 15:07:02 -07:00
Scott Lahteine
81e01152bb Merge pull request #4336 from thinkyhead/rc_bltouch_sensor 
BLTouch probe sensor
 2016-07-17 14:06:32 -07:00
Scott Lahteine
1583177ef4 BLTOUCH probe config option 2016-07-17 13:55:38 -07:00
Scott Lahteine
39706f3e57 Endstop invert flags as macros instead of const bool 2016-07-17 13:51:02 -07:00
Scott Lahteine
671634bf11 Fix spacing after section header 2016-07-17 13:35:21 -07:00
Scott Lahteine
22b4cff423 New extruder type configuration options 2016-07-17 00:13:56 -07:00
Scott Lahteine
bf16ae5a70 Merge pull request #4299 from jbrazio/feature/g27-park-nozzle 
Implements park nozzle feature
 2016-07-16 23:47:12 -07:00
João Brázio
fa4274cf4c Improves the custom bootscreen logo feature 2016-07-17 01:31:44 +01:00
João Brázio
9a00108cb6 Adds the WEBSITE_URL as the boot screen line 2 2016-07-16 12:24:37 +01:00
João Brázio
c711701626 Implements a nozzle parking command (G27) 2016-07-16 12:07:59 +01:00
João Brázio
68c343a09a Added G12 configuration options to all configs 2016-07-14 00:38:42 +01:00
João Brázio
021544f572 Improves G12 zig-zag pattern 2016-07-13 21:14:56 +01:00
João Brázio
b05a75655a Implements a nozzle cleaning pattern generator (G12) 2016-07-13 21:14:19 +01:00
Scott Lahteine
a8b6b6a128 Merge pull request #4252 from thinkyhead/rc_rename_hpb 
Replace PLA/ABS preheating with generic
 2016-07-12 20:00:33 -07:00
Scott Lahteine
928ff6487a Greek language pack from @psavva 2016-07-10 18:59:04 -07:00
Scott Lahteine
182c8d7f8f Dyze High Temp Thermistor Support 2016-07-10 17:59:05 -07:00
Scott Lahteine
1026e5b071 Replace PLA/ABS preheating with generic 2016-07-09 18:06:51 -07:00
Petr Zahradnik
e282d69f63 Print job timer comment changed 2016-07-09 17:57:54 -07:00
Scott Lahteine
683975cf90 Fix spelling in a config comment 2016-06-28 16:49:13 -07:00
Scott Lahteine
10da7ac86c Combine Z raise before/after options 2016-06-26 13:56:30 -07:00
Scott Lahteine
03c70c1990 SERVO_DEACTIVATION_DELAY => SERVO_DELAY 2016-06-23 14:33:29 -07:00
Scott Lahteine
bd01592816 Goodbye MECHANICAL_PROBE 2016-06-22 17:13:33 -07:00
Scott Lahteine
b590a7dee0 Make Z_RAISE_BETWEEN_PROBINGS a more general option 2016-06-22 14:00:44 -07:00
Scott Lahteine
d50539583a Make XY_PROBE_SPEED a general probe option 2016-06-22 03:04:47 -07:00
Scott Lahteine
2798499b71 XY_TRAVEL_SPEED => XY_PROBE_SPEED 2016-06-22 02:45:25 -07:00
esenapaj
d583ea852d Standardize format description of Panel 2016-06-21 20:51:27 +09:00
Scott Lahteine
3996242e9d Allow Z_MIN_PROBE_REPEATABILITY_TEST solo 2016-06-21 01:56:40 -07:00
Scott Lahteine
9beb3f2f5e Merge pull request #4097 from thinkyhead/rc_fil_runout_cleanup 
FIL_RUNOUT_INVERTING false by default
 2016-06-19 19:46:14 -07:00
Scott Lahteine
f215b30932 Merge pull request #4093 from thinkyhead/rc_probe_without_abl 
Make Z Probe options independent of ABL
 2016-06-19 19:44:25 -07:00
Scott Lahteine
dfbf8b3c2c FIL_RUNOUT_INVERTING false by default 2016-06-19 19:25:26 -07:00
Scott Lahteine
de12228758 Make Z Probe options independent of ABL 2016-06-19 18:47:27 -07:00
Scott Lahteine
f8c278ce4d Cartesio UI display option in all configs 2016-06-19 17:39:46 -07:00
Scott Lahteine
bd4ec727e7 Merge pull request #4066 from thinkyhead/rc_M851_with_probe 
Make M851 standard with a bed probe
 2016-06-17 17:32:55 -07:00
Scott Lahteine
fc56a547d1 Rename movement section to motion 2016-06-17 15:19:43 -07:00
Scott Lahteine
1000563d80 Make M851 standard with a bed probe 2016-06-17 15:19:42 -07:00
Scott Lahteine
47ce810f52 Remove support for XY servo endstops 2016-06-17 14:19:17 -07:00
Scott Lahteine
02e5dad29a Include Croatian in language listings 2016-06-16 16:18:26 -07:00
João Brázio
8ccd97e7cc
Updated all example configuration files 2016-06-12 00:36:15 +01:00
João Brázio
de8108648f
Added a versioning system to the config files 2016-06-11 23:48:10 +01:00
Reid Rankin
16212432c9 G20/21 and M149 support, and code_value() refactor 
This is an update of MarlinDev PR #196.

G20/21: support for switching input units between millimeters and
inches.
M149: support for changing input temperature units.

In support of these changes, code_value() and code_value_short() are
replaced with an array of functions which handle converting to the
proper types and/or units.
 2016-06-08 16:51:10 -07:00
Scott Lahteine
cd441ce652 SINGLENOZZLE: EXTRUDERS versus HOTENDS 2016-06-03 17:38:03 -07:00
Scott Lahteine
db0fd021d0 Z raise options independent of ABL so G28 can use them 2016-06-02 16:56:49 -07:00
Scott Lahteine
28fb1f8994 Tweak #endif comment for ABL GRID 2016-06-02 16:56:49 -07:00
Scott Lahteine
a0b000d752 Support for SAV_3DGLCD OLED LCD controller 2016-05-31 14:41:16 -07:00
Edward Patel
eb2746a34f MBL: Fix for negative x/y positions 2016-05-28 21:05:43 +02:00
Scott Lahteine
fe3122774a Merge pull request #3806 from thinkyhead/rc_coreyz_support 
Support for COREYZ. Fixes for COREXY, COREXZ
 2016-05-26 18:50:43 -07:00
Scott Lahteine
89e630b2fb Merge pull request #3808 from thinkyhead/rc_singlenozzle 
SINGLENOZZLE
 2016-05-23 15:52:19 -07:00
Scott Lahteine
95fee8ca81 Add option for CoreYZ kinematics 2016-05-23 13:58:40 -07:00
Scott Lahteine
c5130fd23b Additional instructions for controller reverse options 2016-05-20 18:14:50 -07:00
Scott Lahteine
69abfef82e Add "SINGLENOZZLE" extruder option 2016-05-20 15:45:11 -07:00
Scott Lahteine
37c6d0f4ed Reword MESH_G28_REST_ORIGIN comment 2016-05-20 11:52:27 -07:00
Edward Patel
c7d90dc5ec Add option to configure G28 all axis resting position for MBL 2016-05-20 11:52:27 -07:00
João Brázio
f9a62f6a8e Added PRINTJOB_TIMER_AUTOSTART section to example config files 2016-05-14 15:22:45 -07:00
João Brázio
8a18c52002 Adds an option to disable print job timer auto start 2016-05-14 15:22:44 -07:00
Scott Lahteine
f13c4a9ec4 Merge pull request #3720 from jbrazio/feature/host-keepalive 
Removes the DISABLE from HOST_KEEPALIVE
 2016-05-14 14:39:31 -07:00
Scott Lahteine
14cd0f4c92 Merge pull request #3740 from thinkyhead/rc_lcd_home_options 
Individual Axis Homing LCD menu items
 2016-05-12 11:59:46 -07:00
João Brázio
09150cae79 Individual Axis Homing LCD menu items 2016-05-11 19:28:19 -07:00
Scott Lahteine
4dc4e2063f Add REVERSE_ENCODER_DIRECTION option 2016-05-11 15:39:28 -07:00
João Brázio
85b2c80838
Updated example configurations 2016-05-11 01:45:49 +01:00
João Brázio
ac7f634956
Removed the DISABLE from HOST_KEEPALIVE_FEATURE option 2016-05-11 01:45:49 +01:00
João Brázio
aa5a4716cf
Update default config 2016-05-10 13:37:21 +01:00
esenapaj
212b17d510 Fix for PR #3526(Configuration.h LCD & SDCard s... 
Fix for PR #3526(Configuration.h LCD & SDCard section rewrite)

It removes duplicated BQ_LCD_SMART_CONTROLLER.
 2016-05-03 21:35:02 +09:00
Scott Lahteine
c3ef9993b9 Merge pull request #3625 from jbrazio/feature/print-counter 
Print job statistics
 2016-04-29 15:31:14 -07:00
João Brázio
e34f4653ef
Fixed a typo on the configuration files 2016-04-29 23:13:59 +01:00
João Brázio
e2da7e5000
Updated the default configuration and fixed a printcounter.h typo 2016-04-29 23:13:58 +01:00
Scott Lahteine
924285afa6 Merge pull request #3641 from thinkyhead/rc_reverse_menu_doc 
Correct the REVERSE_MENU_DIRECTION comment
 2016-04-28 20:28:46 -07:00
Scott Lahteine
f1b00eb12b Correct the REVERSE_MENU_DIRECTION comment 2016-04-28 20:27:17 -07:00
Scott Lahteine
0c11566f42 Replace LANGUAGE_INCLUDE with LCD_LANGUAGE 2016-04-27 20:06:40 -07:00
Scott Lahteine
259794c0be Make DISPLAY_CHARSET_HD44780 a single setting 2016-04-27 20:06:40 -07:00
João Brázio
170f7e8a45
Rework Marlin's versioning system 2016-04-24 05:21:17 +01:00
Scott Lahteine
0c2aa92b07 Z Safe Homing for all 
The `Z_SAFE_HOMING` feature is coupled with probes and not leveling, so
make it available for general use.
 2016-04-20 17:04:52 -07:00
Scott Lahteine
ef2fd620e9 Suggested fixups for LCD/SD config comments 2016-04-16 19:35:02 -07:00
João Brázio
7b5d6ba315 Rebase & feedback 2016-04-16 19:35:02 -07:00
João Brázio
36a49eab1c Improved the LCD and SD comments blocks in Configuration.h 2016-04-16 19:32:41 -07:00
Scott Lahteine
a8e4d7c135 Merge pull request #3477 from alephobjects/BedTempHysteresis 
Implementation of M190 bed temp hysteresis
 2016-04-15 16:20:58 -07:00
Scott Lahteine
1cc622b167 Fix minor spelling in comments 2016-04-14 20:06:59 -07:00