Merge pull request #4252 from thinkyhead/rc_rename_hpb

Replace PLA/ABS preheating with generic
This commit is contained in:
Scott Lahteine 2016-07-12 20:00:33 -07:00 committed by GitHub
commit a8b6b6a128
52 changed files with 490 additions and 483 deletions

View File

@ -779,13 +779,13 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// @section temperature
// Preheat Constants
#define PLA_PREHEAT_HOTEND_TEMP 180
#define PLA_PREHEAT_HPB_TEMP 70
#define PLA_PREHEAT_FAN_SPEED 0 // Insert Value between 0 and 255
#define PREHEAT_1_TEMP_HOTEND 180
#define PREHEAT_1_TEMP_BED 70
#define PREHEAT_1_FAN_SPEED 0 // Value from 0 to 255
#define ABS_PREHEAT_HOTEND_TEMP 240
#define ABS_PREHEAT_HPB_TEMP 110
#define ABS_PREHEAT_FAN_SPEED 0 // Insert Value between 0 and 255
#define PREHEAT_2_TEMP_HOTEND 240
#define PREHEAT_2_TEMP_BED 110
#define PREHEAT_2_FAN_SPEED 0 // Value from 0 to 255
//
// Print job timer

View File

@ -4862,32 +4862,32 @@ inline void gcode_M140() {
case 0:
if (code_seen('H')) {
v = code_value_int();
plaPreheatHotendTemp = constrain(v, EXTRUDE_MINTEMP, HEATER_0_MAXTEMP - 15);
preheatHotendTemp1 = constrain(v, EXTRUDE_MINTEMP, HEATER_0_MAXTEMP - 15);
}
if (code_seen('F')) {
v = code_value_int();
plaPreheatFanSpeed = constrain(v, 0, 255);
preheatFanSpeed1 = constrain(v, 0, 255);
}
#if TEMP_SENSOR_BED != 0
if (code_seen('B')) {
v = code_value_int();
plaPreheatHPBTemp = constrain(v, BED_MINTEMP, BED_MAXTEMP - 15);
preheatBedTemp1 = constrain(v, BED_MINTEMP, BED_MAXTEMP - 15);
}
#endif
break;
case 1:
if (code_seen('H')) {
v = code_value_int();
absPreheatHotendTemp = constrain(v, EXTRUDE_MINTEMP, HEATER_0_MAXTEMP - 15);
preheatHotendTemp2 = constrain(v, EXTRUDE_MINTEMP, HEATER_0_MAXTEMP - 15);
}
if (code_seen('F')) {
v = code_value_int();
absPreheatFanSpeed = constrain(v, 0, 255);
preheatFanSpeed2 = constrain(v, 0, 255);
}
#if TEMP_SENSOR_BED != 0
if (code_seen('B')) {
v = code_value_int();
absPreheatHPBTemp = constrain(v, BED_MINTEMP, BED_MAXTEMP - 15);
preheatBedTemp2 = constrain(v, BED_MINTEMP, BED_MAXTEMP - 15);
}
#endif
break;

View File

@ -632,6 +632,18 @@
#error "SERVO_DEACTIVATION_DELAY is deprecated. Use SERVO_DELAY instead."
#elif ENABLED(FILAMENTCHANGEENABLE)
#error "FILAMENTCHANGEENABLE is now FILAMENT_CHANGE_FEATURE. Please update your configuration."
#elif defined(PLA_PREHEAT_HOTEND_TEMP)
#error "PLA_PREHEAT_HOTEND_TEMP is now PREHEAT_1_TEMP_HOTEND. Please update your configuration."
#elif defined(PLA_PREHEAT_HPB_TEMP)
#error "PLA_PREHEAT_HPB_TEMP is now PREHEAT_1_TEMP_BED. Please update your configuration."
#elif defined(PLA_PREHEAT_FAN_SPEED)
#error "PLA_PREHEAT_FAN_SPEED is now PREHEAT_1_FAN_SPEED. Please update your configuration."
#elif defined(ABS_PREHEAT_HOTEND_TEMP)
#error "ABS_PREHEAT_HOTEND_TEMP is now PREHEAT_2_TEMP_HOTEND. Please update your configuration."
#elif defined(ABS_PREHEAT_HPB_TEMP)
#error "ABS_PREHEAT_HPB_TEMP is now PREHEAT_2_TEMP_BED. Please update your configuration."
#elif defined(ABS_PREHEAT_FAN_SPEED)
#error "ABS_PREHEAT_FAN_SPEED is now PREHEAT_2_FAN_SPEED. Please update your configuration."
#endif
#endif //SANITYCHECK_H

View File

@ -85,12 +85,12 @@
* 285 M666 Z z_endstop_adj (float)
*
* ULTIPANEL:
* 289 M145 S0 H plaPreheatHotendTemp (int)
* 291 M145 S0 B plaPreheatHPBTemp (int)
* 293 M145 S0 F plaPreheatFanSpeed (int)
* 295 M145 S1 H absPreheatHotendTemp (int)
* 297 M145 S1 B absPreheatHPBTemp (int)
* 299 M145 S1 F absPreheatFanSpeed (int)
* 289 M145 S0 H preheatHotendTemp1 (int)
* 291 M145 S0 B preheatBedTemp1 (int)
* 293 M145 S0 F preheatFanSpeed1 (int)
* 295 M145 S1 H preheatHotendTemp2 (int)
* 297 M145 S1 B preheatBedTemp2 (int)
* 299 M145 S1 F preheatFanSpeed2 (int)
*
* PIDTEMP:
* 301 M301 E0 PIDC Kp[0], Ki[0], Kd[0], Kc[0] (float x4)
@ -262,16 +262,16 @@ void Config_StoreSettings() {
#endif
#if DISABLED(ULTIPANEL)
int plaPreheatHotendTemp = PLA_PREHEAT_HOTEND_TEMP, plaPreheatHPBTemp = PLA_PREHEAT_HPB_TEMP, plaPreheatFanSpeed = PLA_PREHEAT_FAN_SPEED,
absPreheatHotendTemp = ABS_PREHEAT_HOTEND_TEMP, absPreheatHPBTemp = ABS_PREHEAT_HPB_TEMP, absPreheatFanSpeed = ABS_PREHEAT_FAN_SPEED;
int preheatHotendTemp1 = PREHEAT_1_TEMP_HOTEND, preheatBedTemp1 = PREHEAT_1_TEMP_BED, preheatFanSpeed1 = PREHEAT_1_FAN_SPEED,
preheatHotendTemp2 = PREHEAT_2_TEMP_HOTEND, preheatBedTemp2 = PREHEAT_2_TEMP_BED, preheatFanSpeed2 = PREHEAT_2_FAN_SPEED;
#endif // !ULTIPANEL
EEPROM_WRITE_VAR(i, plaPreheatHotendTemp);
EEPROM_WRITE_VAR(i, plaPreheatHPBTemp);
EEPROM_WRITE_VAR(i, plaPreheatFanSpeed);
EEPROM_WRITE_VAR(i, absPreheatHotendTemp);
EEPROM_WRITE_VAR(i, absPreheatHPBTemp);
EEPROM_WRITE_VAR(i, absPreheatFanSpeed);
EEPROM_WRITE_VAR(i, preheatHotendTemp1);
EEPROM_WRITE_VAR(i, preheatBedTemp1);
EEPROM_WRITE_VAR(i, preheatFanSpeed1);
EEPROM_WRITE_VAR(i, preheatHotendTemp2);
EEPROM_WRITE_VAR(i, preheatBedTemp2);
EEPROM_WRITE_VAR(i, preheatFanSpeed2);
for (uint8_t e = 0; e < MAX_EXTRUDERS; e++) {
@ -447,16 +447,16 @@ void Config_RetrieveSettings() {
#endif
#if DISABLED(ULTIPANEL)
int plaPreheatHotendTemp, plaPreheatHPBTemp, plaPreheatFanSpeed,
absPreheatHotendTemp, absPreheatHPBTemp, absPreheatFanSpeed;
int preheatHotendTemp1, preheatBedTemp1, preheatFanSpeed1,
preheatHotendTemp2, preheatBedTemp2, preheatFanSpeed2;
#endif
EEPROM_READ_VAR(i, plaPreheatHotendTemp);
EEPROM_READ_VAR(i, plaPreheatHPBTemp);
EEPROM_READ_VAR(i, plaPreheatFanSpeed);
EEPROM_READ_VAR(i, absPreheatHotendTemp);
EEPROM_READ_VAR(i, absPreheatHPBTemp);
EEPROM_READ_VAR(i, absPreheatFanSpeed);
EEPROM_READ_VAR(i, preheatHotendTemp1);
EEPROM_READ_VAR(i, preheatBedTemp1);
EEPROM_READ_VAR(i, preheatFanSpeed1);
EEPROM_READ_VAR(i, preheatHotendTemp2);
EEPROM_READ_VAR(i, preheatBedTemp2);
EEPROM_READ_VAR(i, preheatFanSpeed2);
#if ENABLED(PIDTEMP)
for (uint8_t e = 0; e < MAX_EXTRUDERS; e++) {
@ -604,12 +604,12 @@ void Config_ResetDefault() {
#endif
#if ENABLED(ULTIPANEL)
plaPreheatHotendTemp = PLA_PREHEAT_HOTEND_TEMP;
plaPreheatHPBTemp = PLA_PREHEAT_HPB_TEMP;
plaPreheatFanSpeed = PLA_PREHEAT_FAN_SPEED;
absPreheatHotendTemp = ABS_PREHEAT_HOTEND_TEMP;
absPreheatHPBTemp = ABS_PREHEAT_HPB_TEMP;
absPreheatFanSpeed = ABS_PREHEAT_FAN_SPEED;
preheatHotendTemp1 = PREHEAT_1_TEMP_HOTEND;
preheatBedTemp1 = PREHEAT_1_TEMP_BED;
preheatFanSpeed1 = PREHEAT_1_FAN_SPEED;
preheatHotendTemp2 = PREHEAT_2_TEMP_HOTEND;
preheatBedTemp2 = PREHEAT_2_TEMP_BED;
preheatFanSpeed2 = PREHEAT_2_FAN_SPEED;
#endif
#if HAS_LCD_CONTRAST
@ -814,14 +814,14 @@ void Config_PrintSettings(bool forReplay) {
SERIAL_ECHOLNPGM("Material heatup parameters:");
CONFIG_ECHO_START;
}
SERIAL_ECHOPAIR(" M145 S0 H", plaPreheatHotendTemp);
SERIAL_ECHOPAIR(" B", plaPreheatHPBTemp);
SERIAL_ECHOPAIR(" F", plaPreheatFanSpeed);
SERIAL_ECHOPAIR(" M145 S0 H", preheatHotendTemp1);
SERIAL_ECHOPAIR(" B", preheatBedTemp1);
SERIAL_ECHOPAIR(" F", preheatFanSpeed1);
SERIAL_EOL;
CONFIG_ECHO_START;
SERIAL_ECHOPAIR(" M145 S1 H", absPreheatHotendTemp);
SERIAL_ECHOPAIR(" B", absPreheatHPBTemp);
SERIAL_ECHOPAIR(" F", absPreheatFanSpeed);
SERIAL_ECHOPAIR(" M145 S1 H", preheatHotendTemp2);
SERIAL_ECHOPAIR(" B", preheatBedTemp2);
SERIAL_ECHOPAIR(" F", preheatFanSpeed2);
SERIAL_EOL;
#endif // ULTIPANEL

View File

@ -778,13 +778,13 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// @section temperature
// Preheat Constants
#define PLA_PREHEAT_HOTEND_TEMP 190
#define PLA_PREHEAT_HPB_TEMP 50
#define PLA_PREHEAT_FAN_SPEED 0 // Insert Value between 0 and 255
#define PREHEAT_1_TEMP_HOTEND 190
#define PREHEAT_1_TEMP_BED 50
#define PREHEAT_1_FAN_SPEED 0 // Value from 0 to 255
#define ABS_PREHEAT_HOTEND_TEMP 240
#define ABS_PREHEAT_HPB_TEMP 110
#define ABS_PREHEAT_FAN_SPEED 0 // Insert Value between 0 and 255
#define PREHEAT_2_TEMP_HOTEND 240
#define PREHEAT_2_TEMP_BED 110
#define PREHEAT_2_FAN_SPEED 0 // Value from 0 to 255
//
// Print job timer

View File

@ -762,13 +762,13 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// @section temperature
// Preheat Constants
#define PLA_PREHEAT_HOTEND_TEMP 180
#define PLA_PREHEAT_HPB_TEMP 70
#define PLA_PREHEAT_FAN_SPEED 255 // Insert Value between 0 and 255
#define PREHEAT_1_TEMP_HOTEND 180
#define PREHEAT_1_TEMP_BED 70
#define PREHEAT_1_FAN_SPEED 255 // Value from 0 to 255
#define ABS_PREHEAT_HOTEND_TEMP 240
#define ABS_PREHEAT_HPB_TEMP 100
#define ABS_PREHEAT_FAN_SPEED 255 // Insert Value between 0 and 255
#define PREHEAT_2_TEMP_HOTEND 240
#define PREHEAT_2_TEMP_BED 100
#define PREHEAT_2_FAN_SPEED 255 // Value from 0 to 255
//
// Print job timer

View File

@ -760,13 +760,13 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// @section temperature
// Preheat Constants
#define PLA_PREHEAT_HOTEND_TEMP 180
#define PLA_PREHEAT_HPB_TEMP 70
#define PLA_PREHEAT_FAN_SPEED 255 // Insert Value between 0 and 255
#define PREHEAT_1_TEMP_HOTEND 180
#define PREHEAT_1_TEMP_BED 70
#define PREHEAT_1_FAN_SPEED 255 // Value from 0 to 255
#define ABS_PREHEAT_HOTEND_TEMP 240
#define ABS_PREHEAT_HPB_TEMP 100
#define ABS_PREHEAT_FAN_SPEED 255 // Insert Value between 0 and 255
#define PREHEAT_2_TEMP_HOTEND 240
#define PREHEAT_2_TEMP_BED 100
#define PREHEAT_2_FAN_SPEED 255 // Value from 0 to 255
//
// Print job timer

View File

@ -771,13 +771,13 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
// @section temperature
// Preheat Constants
#define PLA_PREHEAT_HOTEND_TEMP 200
#define PLA_PREHEAT_HPB_TEMP 0
#define PLA_PREHEAT_FAN_SPEED 255 // Insert Value between 0 and 255
#define PREHEAT_1_TEMP_HOTEND 200
#define PREHEAT_1_TEMP_BED 0
#define PREHEAT_1_FAN_SPEED 255 // Value from 0 to 255
#define ABS_PREHEAT_HOTEND_TEMP 220
#define ABS_PREHEAT_HPB_TEMP 100
#define ABS_PREHEAT_FAN_SPEED 255 // Insert Value between 0 and 255
#define PREHEAT_2_TEMP_HOTEND 220
#define PREHEAT_2_TEMP_BED 100
#define PREHEAT_2_FAN_SPEED 255 // Value from 0 to 255
//
// Print job timer

View File

@ -773,13 +773,13 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// @section temperature
// Preheat Constants
#define PLA_PREHEAT_HOTEND_TEMP 210
#define PLA_PREHEAT_HPB_TEMP 70
#define PLA_PREHEAT_FAN_SPEED 0 // Insert Value between 0 and 255
#define PREHEAT_1_TEMP_HOTEND 210
#define PREHEAT_1_TEMP_BED 70
#define PREHEAT_1_FAN_SPEED 0 // Value from 0 to 255
#define ABS_PREHEAT_HOTEND_TEMP 240
#define ABS_PREHEAT_HPB_TEMP 110
#define ABS_PREHEAT_FAN_SPEED 0 // Insert Value between 0 and 255
#define PREHEAT_2_TEMP_HOTEND 240
#define PREHEAT_2_TEMP_BED 110
#define PREHEAT_2_FAN_SPEED 0 // Value from 0 to 255
//
// Print job timer

View File

@ -796,13 +796,13 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// @section temperature
// Preheat Constants
#define PLA_PREHEAT_HOTEND_TEMP 190
#define PLA_PREHEAT_HPB_TEMP 50 // K8200: set back to 70 if you have an upgraded heatbed power supply
#define PLA_PREHEAT_FAN_SPEED 0 // Insert Value between 0 and 255
#define PREHEAT_1_TEMP_HOTEND 190
#define PREHEAT_1_TEMP_BED 50 // K8200: set back to 70 if you have an upgraded heatbed power supply
#define PREHEAT_1_FAN_SPEED 0 // Value from 0 to 255
#define ABS_PREHEAT_HOTEND_TEMP 240
#define ABS_PREHEAT_HPB_TEMP 60 // K8200: set back to 110 if you have an upgraded heatbed power supply
#define ABS_PREHEAT_FAN_SPEED 0 // Insert Value between 0 and 255
#define PREHEAT_2_TEMP_HOTEND 240
#define PREHEAT_2_TEMP_BED 60 // K8200: set back to 110 if you have an upgraded heatbed power supply
#define PREHEAT_2_FAN_SPEED 0 // Value from 0 to 255
//
// Print job timer

View File

@ -779,13 +779,13 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
// @section temperature
// Preheat Constants
#define PLA_PREHEAT_HOTEND_TEMP 210
#define PLA_PREHEAT_HPB_TEMP 0
#define PLA_PREHEAT_FAN_SPEED 165 // Insert Value between 0 and 255
#define PREHEAT_1_TEMP_HOTEND 210
#define PREHEAT_1_TEMP_BED 0
#define PREHEAT_1_FAN_SPEED 165 // Value from 0 to 255
#define ABS_PREHEAT_HOTEND_TEMP 245
#define ABS_PREHEAT_HPB_TEMP 0
#define ABS_PREHEAT_FAN_SPEED 165 // Insert Value between 0 and 255
#define PREHEAT_2_TEMP_HOTEND 245
#define PREHEAT_2_TEMP_BED 0
#define PREHEAT_2_FAN_SPEED 165 // Value from 0 to 255
//
// Print job timer

View File

@ -779,13 +779,13 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
// @section temperature
// Preheat Constants
#define PLA_PREHEAT_HOTEND_TEMP 210
#define PLA_PREHEAT_HPB_TEMP 0
#define PLA_PREHEAT_FAN_SPEED 165 // Insert Value between 0 and 255
#define PREHEAT_1_TEMP_HOTEND 210
#define PREHEAT_1_TEMP_BED 0
#define PREHEAT_1_FAN_SPEED 165 // Value from 0 to 255
#define ABS_PREHEAT_HOTEND_TEMP 245
#define ABS_PREHEAT_HPB_TEMP 0
#define ABS_PREHEAT_FAN_SPEED 165 // Insert Value between 0 and 255
#define PREHEAT_2_TEMP_HOTEND 245
#define PREHEAT_2_TEMP_BED 0
#define PREHEAT_2_FAN_SPEED 165 // Value from 0 to 255
//
// Print job timer

View File

@ -779,13 +779,13 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// @section temperature
// Preheat Constants
#define PLA_PREHEAT_HOTEND_TEMP 180
#define PLA_PREHEAT_HPB_TEMP 70
#define PLA_PREHEAT_FAN_SPEED 0 // Insert Value between 0 and 255
#define PREHEAT_1_TEMP_HOTEND 180
#define PREHEAT_1_TEMP_BED 70
#define PREHEAT_1_FAN_SPEED 0 // Value from 0 to 255
#define ABS_PREHEAT_HOTEND_TEMP 240
#define ABS_PREHEAT_HPB_TEMP 110
#define ABS_PREHEAT_FAN_SPEED 0 // Insert Value between 0 and 255
#define PREHEAT_2_TEMP_HOTEND 240
#define PREHEAT_2_TEMP_BED 110
#define PREHEAT_2_FAN_SPEED 0 // Value from 0 to 255
//
// Print job timer

View File

@ -777,13 +777,13 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// @section temperature
// Preheat Constants
#define PLA_PREHEAT_HOTEND_TEMP 180
#define PLA_PREHEAT_HPB_TEMP 70
#define PLA_PREHEAT_FAN_SPEED 255 // Insert Value between 0 and 255
#define PREHEAT_1_TEMP_HOTEND 180
#define PREHEAT_1_TEMP_BED 70
#define PREHEAT_1_FAN_SPEED 255 // Value from 0 to 255
#define ABS_PREHEAT_HOTEND_TEMP 240
#define ABS_PREHEAT_HPB_TEMP 110
#define ABS_PREHEAT_FAN_SPEED 255 // Insert Value between 0 and 255
#define PREHEAT_2_TEMP_HOTEND 240
#define PREHEAT_2_TEMP_BED 110
#define PREHEAT_2_FAN_SPEED 255 // Value from 0 to 255
//
// Print job timer

View File

@ -787,13 +787,13 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// @section temperature
// Preheat Constants
#define PLA_PREHEAT_HOTEND_TEMP 180
#define PLA_PREHEAT_HPB_TEMP 70
#define PLA_PREHEAT_FAN_SPEED 255 // Insert Value between 0 and 255
#define PREHEAT_1_TEMP_HOTEND 180
#define PREHEAT_1_TEMP_BED 70
#define PREHEAT_1_FAN_SPEED 255 // Value from 0 to 255
#define ABS_PREHEAT_HOTEND_TEMP 240
#define ABS_PREHEAT_HPB_TEMP 100
#define ABS_PREHEAT_FAN_SPEED 255 // Insert Value between 0 and 255
#define PREHEAT_2_TEMP_HOTEND 240
#define PREHEAT_2_TEMP_BED 100
#define PREHEAT_2_FAN_SPEED 255 // Value from 0 to 255
//
// Print job timer

View File

@ -800,13 +800,13 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// @section temperature
// Preheat Constants
#define PLA_PREHEAT_HOTEND_TEMP 180
#define PLA_PREHEAT_HPB_TEMP 70
#define PLA_PREHEAT_FAN_SPEED 0 // Insert Value between 0 and 255
#define PREHEAT_1_TEMP_HOTEND 180
#define PREHEAT_1_TEMP_BED 70
#define PREHEAT_1_FAN_SPEED 0 // Value from 0 to 255
#define ABS_PREHEAT_HOTEND_TEMP 230
#define ABS_PREHEAT_HPB_TEMP 110
#define ABS_PREHEAT_FAN_SPEED 0 // Insert Value between 0 and 255
#define PREHEAT_2_TEMP_HOTEND 230
#define PREHEAT_2_TEMP_BED 110
#define PREHEAT_2_FAN_SPEED 0 // Value from 0 to 255
//
// Print job timer

View File

@ -771,13 +771,13 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
// @section temperature
// Preheat Constants
#define PLA_PREHEAT_HOTEND_TEMP 200
#define PLA_PREHEAT_HPB_TEMP 0
#define PLA_PREHEAT_FAN_SPEED 255 // Insert Value between 0 and 255
#define PREHEAT_1_TEMP_HOTEND 200
#define PREHEAT_1_TEMP_BED 0
#define PREHEAT_1_FAN_SPEED 255 // Value from 0 to 255
#define ABS_PREHEAT_HOTEND_TEMP 220
#define ABS_PREHEAT_HPB_TEMP 100
#define ABS_PREHEAT_FAN_SPEED 255 // Insert Value between 0 and 255
#define PREHEAT_2_TEMP_HOTEND 220
#define PREHEAT_2_TEMP_BED 100
#define PREHEAT_2_FAN_SPEED 255 // Value from 0 to 255
//
// Print job timer

View File

@ -779,13 +779,13 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// @section temperature
// Preheat Constants
#define PLA_PREHEAT_HOTEND_TEMP 180
#define PLA_PREHEAT_HPB_TEMP 70
#define PLA_PREHEAT_FAN_SPEED 0 // Insert Value between 0 and 255
#define PREHEAT_1_TEMP_HOTEND 180
#define PREHEAT_1_TEMP_BED 70
#define PREHEAT_1_FAN_SPEED 0 // Value from 0 to 255
#define ABS_PREHEAT_HOTEND_TEMP 240
#define ABS_PREHEAT_HPB_TEMP 110
#define ABS_PREHEAT_FAN_SPEED 0 // Insert Value between 0 and 255
#define PREHEAT_2_TEMP_HOTEND 240
#define PREHEAT_2_TEMP_BED 110
#define PREHEAT_2_FAN_SPEED 0 // Value from 0 to 255
//
// Print job timer

View File

@ -874,13 +874,13 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
// @section temperature
// Preheat Constants
#define PLA_PREHEAT_HOTEND_TEMP 180
#define PLA_PREHEAT_HPB_TEMP 70
#define PLA_PREHEAT_FAN_SPEED 255 // Insert Value between 0 and 255
#define PREHEAT_1_TEMP_HOTEND 180
#define PREHEAT_1_TEMP_BED 70
#define PREHEAT_1_FAN_SPEED 255 // Value from 0 to 255
#define ABS_PREHEAT_HOTEND_TEMP 240
#define ABS_PREHEAT_HPB_TEMP 100
#define ABS_PREHEAT_FAN_SPEED 255 // Insert Value between 0 and 255
#define PREHEAT_2_TEMP_HOTEND 240
#define PREHEAT_2_TEMP_BED 100
#define PREHEAT_2_FAN_SPEED 255 // Value from 0 to 255
//
// Print job timer

View File

@ -868,13 +868,13 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
// @section temperature
// Preheat Constants
#define PLA_PREHEAT_HOTEND_TEMP 180
#define PLA_PREHEAT_HPB_TEMP 70
#define PLA_PREHEAT_FAN_SPEED 255 // Insert Value between 0 and 255
#define PREHEAT_1_TEMP_HOTEND 180
#define PREHEAT_1_TEMP_BED 70
#define PREHEAT_1_FAN_SPEED 255 // Value from 0 to 255
#define ABS_PREHEAT_HOTEND_TEMP 240
#define ABS_PREHEAT_HPB_TEMP 100
#define ABS_PREHEAT_FAN_SPEED 255 // Insert Value between 0 and 255
#define PREHEAT_2_TEMP_HOTEND 240
#define PREHEAT_2_TEMP_BED 100
#define PREHEAT_2_FAN_SPEED 255 // Value from 0 to 255
//
// Print job timer

View File

@ -871,13 +871,13 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// @section temperature
// Preheat Constants
#define PLA_PREHEAT_HOTEND_TEMP 180
#define PLA_PREHEAT_HPB_TEMP 70
#define PLA_PREHEAT_FAN_SPEED 255 // Insert Value between 0 and 255
#define PREHEAT_1_TEMP_HOTEND 180
#define PREHEAT_1_TEMP_BED 70
#define PREHEAT_1_FAN_SPEED 255 // Value from 0 to 255
#define ABS_PREHEAT_HOTEND_TEMP 240
#define ABS_PREHEAT_HPB_TEMP 100
#define ABS_PREHEAT_FAN_SPEED 255 // Insert Value between 0 and 255
#define PREHEAT_2_TEMP_HOTEND 240
#define PREHEAT_2_TEMP_BED 100
#define PREHEAT_2_FAN_SPEED 255 // Value from 0 to 255
//
// Print job timer

View File

@ -871,13 +871,13 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// @section temperature
// Preheat Constants
#define PLA_PREHEAT_HOTEND_TEMP 180
#define PLA_PREHEAT_HPB_TEMP 70
#define PLA_PREHEAT_FAN_SPEED 255 // Insert Value between 0 and 255
#define PREHEAT_1_TEMP_HOTEND 180
#define PREHEAT_1_TEMP_BED 70
#define PREHEAT_1_FAN_SPEED 255 // Value from 0 to 255
#define ABS_PREHEAT_HOTEND_TEMP 240
#define ABS_PREHEAT_HPB_TEMP 100
#define ABS_PREHEAT_FAN_SPEED 255 // Insert Value between 0 and 255
#define PREHEAT_2_TEMP_HOTEND 240
#define PREHEAT_2_TEMP_BED 100
#define PREHEAT_2_FAN_SPEED 255 // Value from 0 to 255
//
// Print job timer

View File

@ -873,13 +873,13 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// @section temperature
// Preheat Constants
#define PLA_PREHEAT_HOTEND_TEMP 180
#define PLA_PREHEAT_HPB_TEMP 70
#define PLA_PREHEAT_FAN_SPEED 255 // Insert Value between 0 and 255
#define PREHEAT_1_TEMP_HOTEND 180
#define PREHEAT_1_TEMP_BED 70
#define PREHEAT_1_FAN_SPEED 255 // Value from 0 to 255
#define ABS_PREHEAT_HOTEND_TEMP 240
#define ABS_PREHEAT_HPB_TEMP 100
#define ABS_PREHEAT_FAN_SPEED 255 // Insert Value between 0 and 255
#define PREHEAT_2_TEMP_HOTEND 240
#define PREHEAT_2_TEMP_BED 100
#define PREHEAT_2_FAN_SPEED 255 // Value from 0 to 255
//
// Print job timer

View File

@ -782,13 +782,13 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// @section temperature
// Preheat Constants
#define PLA_PREHEAT_HOTEND_TEMP 180
#define PLA_PREHEAT_HPB_TEMP 70
#define PLA_PREHEAT_FAN_SPEED 255 // Insert Value between 0 and 255
#define PREHEAT_1_TEMP_HOTEND 180
#define PREHEAT_1_TEMP_BED 70
#define PREHEAT_1_FAN_SPEED 255 // Value from 0 to 255
#define ABS_PREHEAT_HOTEND_TEMP 240
#define ABS_PREHEAT_HPB_TEMP 100
#define ABS_PREHEAT_FAN_SPEED 255 // Insert Value between 0 and 255
#define PREHEAT_2_TEMP_HOTEND 240
#define PREHEAT_2_TEMP_BED 100
#define PREHEAT_2_FAN_SPEED 255 // Value from 0 to 255
//
// Print job timer

View File

@ -773,13 +773,13 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
// @section temperature
// Preheat Constants
#define PLA_PREHEAT_HOTEND_TEMP 180
#define PLA_PREHEAT_HPB_TEMP 70
#define PLA_PREHEAT_FAN_SPEED 255 // Insert Value between 0 and 255
#define PREHEAT_1_TEMP_HOTEND 180
#define PREHEAT_1_TEMP_BED 70
#define PREHEAT_1_FAN_SPEED 255 // Value from 0 to 255
#define ABS_PREHEAT_HOTEND_TEMP 240
#define ABS_PREHEAT_HPB_TEMP 100
#define ABS_PREHEAT_FAN_SPEED 255 // Insert Value between 0 and 255
#define PREHEAT_2_TEMP_HOTEND 240
#define PREHEAT_2_TEMP_BED 100
#define PREHEAT_2_FAN_SPEED 255 // Value from 0 to 255
//
// Print job timer

View File

@ -48,16 +48,16 @@
#define MSG_SET_HOME_OFFSETS "Set home offsets"
#define MSG_HOME_OFFSETS_APPLIED "Offsets applied"
#define MSG_SET_ORIGIN "Establir zero"
#define MSG_PREHEAT_PLA "Precalentar PLA"
#define MSG_PREHEAT_PLA_N "Precalentar PLA "
#define MSG_PREHEAT_PLA_ALL "Precalentar PLA a"
#define MSG_PREHEAT_PLA_BEDONLY "Prec. PLA Base"
#define MSG_PREHEAT_PLA_SETTINGS "Achustar tem. PLA"
#define MSG_PREHEAT_ABS "Precalentar ABS"
#define MSG_PREHEAT_ABS_N "Precalentar ABS "
#define MSG_PREHEAT_ABS_ALL "Precalentar ABS a"
#define MSG_PREHEAT_ABS_BEDONLY "Prec. ABS Base"
#define MSG_PREHEAT_ABS_SETTINGS "Achustar tem. ABS"
#define MSG_PREHEAT_1 "Precalentar PLA"
#define MSG_PREHEAT_1_N "Precalentar PLA "
#define MSG_PREHEAT_1_ALL "Precalentar PLA a"
#define MSG_PREHEAT_1_BEDONLY "Prec. PLA Base"
#define MSG_PREHEAT_1_SETTINGS "Achustar tem. PLA"
#define MSG_PREHEAT_2 "Precalentar ABS"
#define MSG_PREHEAT_2_N "Precalentar ABS "
#define MSG_PREHEAT_2_ALL "Precalentar ABS a"
#define MSG_PREHEAT_2_BEDONLY "Prec. ABS Base"
#define MSG_PREHEAT_2_SETTINGS "Achustar tem. ABS"
#define MSG_COOLDOWN "Enfriar"
#define MSG_SWITCH_PS_ON "Enchegar Fuent"
#define MSG_SWITCH_PS_OFF "Desenchegar Fuent"

View File

@ -49,16 +49,16 @@
#define MSG_SET_HOME_OFFSETS "Задай Начало"
#define MSG_HOME_OFFSETS_APPLIED "Offsets applied"
#define MSG_SET_ORIGIN "Изходна точка"
#define MSG_PREHEAT_PLA "Подгряване PLA"
#define MSG_PREHEAT_PLA_N "Подгряване PLA"
#define MSG_PREHEAT_PLA_ALL "Подгр. PLA Всички"
#define MSG_PREHEAT_PLA_BEDONLY "Подгр. PLA Легло"
#define MSG_PREHEAT_PLA_SETTINGS "Настройки PLA"
#define MSG_PREHEAT_ABS "Подгряване ABS"
#define MSG_PREHEAT_ABS_N "Подгряване ABS"
#define MSG_PREHEAT_ABS_ALL "Подгр. ABS Всички"
#define MSG_PREHEAT_ABS_BEDONLY "Подгр. ABS Легло"
#define MSG_PREHEAT_ABS_SETTINGS "Настройки ABS"
#define MSG_PREHEAT_1 "Подгряване PLA"
#define MSG_PREHEAT_1_N "Подгряване PLA"
#define MSG_PREHEAT_1_ALL "Подгр. PLA Всички"
#define MSG_PREHEAT_1_BEDONLY "Подгр. PLA Легло"
#define MSG_PREHEAT_1_SETTINGS "Настройки PLA"
#define MSG_PREHEAT_2 "Подгряване ABS"
#define MSG_PREHEAT_2_N "Подгряване ABS"
#define MSG_PREHEAT_2_ALL "Подгр. ABS Всички"
#define MSG_PREHEAT_2_BEDONLY "Подгр. ABS Легло"
#define MSG_PREHEAT_2_SETTINGS "Настройки ABS"
#define MSG_COOLDOWN "Охлаждане"
#define MSG_SWITCH_PS_ON "Вкл. захранване"
#define MSG_SWITCH_PS_OFF "Изкл. захранване"

View File

@ -49,16 +49,16 @@
#define MSG_SET_HOME_OFFSETS "Set home offsets"
#define MSG_HOME_OFFSETS_APPLIED "Offsets applied"
#define MSG_SET_ORIGIN "Establir origen"
#define MSG_PREHEAT_PLA "Preescalfar PLA"
#define MSG_PREHEAT_PLA_N "Preescalfar PLA "
#define MSG_PREHEAT_PLA_ALL "Preesc. tot PLA"
#define MSG_PREHEAT_PLA_BEDONLY "Preesc. llit PLA"
#define MSG_PREHEAT_PLA_SETTINGS "Configuració PLA"
#define MSG_PREHEAT_ABS "Preescalfar ABS"
#define MSG_PREHEAT_ABS_N "Preescalfar ABS "
#define MSG_PREHEAT_ABS_ALL "Preesc. tot ABS"
#define MSG_PREHEAT_ABS_BEDONLY "Preesc. llit ABS"
#define MSG_PREHEAT_ABS_SETTINGS "Configuració ABS"
#define MSG_PREHEAT_1 "Preescalfar PLA"
#define MSG_PREHEAT_1_N "Preescalfar PLA "
#define MSG_PREHEAT_1_ALL "Preesc. tot PLA"
#define MSG_PREHEAT_1_BEDONLY "Preesc. llit PLA"
#define MSG_PREHEAT_1_SETTINGS "Configuració PLA"
#define MSG_PREHEAT_2 "Preescalfar ABS"
#define MSG_PREHEAT_2_N "Preescalfar ABS "
#define MSG_PREHEAT_2_ALL "Preesc. tot ABS"
#define MSG_PREHEAT_2_BEDONLY "Preesc. llit ABS"
#define MSG_PREHEAT_2_SETTINGS "Configuració ABS"
#define MSG_COOLDOWN "Refredar"
#define MSG_SWITCH_PS_ON "Switch power on"
#define MSG_SWITCH_PS_OFF "Switch power off"

View File

@ -45,16 +45,16 @@
#define MSG_SET_HOME_OFFSETS "\xbe\xbf\xbb\xbc\xbd\xc0\xc1"
#define MSG_HOME_OFFSETS_APPLIED "Offsets applied"
#define MSG_SET_ORIGIN "\xbe\xbf\xbc\xbd"
#define MSG_PREHEAT_PLA "\xc3\xc4 PLA"
#define MSG_PREHEAT_PLA_N MSG_PREHEAT_PLA " "
#define MSG_PREHEAT_PLA_ALL MSG_PREHEAT_PLA " \xc5\xc6"
#define MSG_PREHEAT_PLA_BEDONLY MSG_PREHEAT_PLA " \xc4\xc7"
#define MSG_PREHEAT_PLA_SETTINGS MSG_PREHEAT_PLA " \xbe\xbf"
#define MSG_PREHEAT_ABS "\xc3\xc4 ABS"
#define MSG_PREHEAT_ABS_N MSG_PREHEAT_ABS " "
#define MSG_PREHEAT_ABS_ALL MSG_PREHEAT_ABS " \xc5\xc6"
#define MSG_PREHEAT_ABS_BEDONLY MSG_PREHEAT_ABS " \xbe\xc6"
#define MSG_PREHEAT_ABS_SETTINGS MSG_PREHEAT_ABS " \xbe\xbf"
#define MSG_PREHEAT_1 "\xc3\xc4 PLA"
#define MSG_PREHEAT_1_N MSG_PREHEAT_1 " "
#define MSG_PREHEAT_1_ALL MSG_PREHEAT_1 " \xc5\xc6"
#define MSG_PREHEAT_1_BEDONLY MSG_PREHEAT_1 " \xc4\xc7"
#define MSG_PREHEAT_1_SETTINGS MSG_PREHEAT_1 " \xbe\xbf"
#define MSG_PREHEAT_2 "\xc3\xc4 ABS"
#define MSG_PREHEAT_2_N MSG_PREHEAT_2 " "
#define MSG_PREHEAT_2_ALL MSG_PREHEAT_2 " \xc5\xc6"
#define MSG_PREHEAT_2_BEDONLY MSG_PREHEAT_2 " \xbe\xc6"
#define MSG_PREHEAT_2_SETTINGS MSG_PREHEAT_2 " \xbe\xbf"
#define MSG_COOLDOWN "\xc8\xc9"
#define MSG_SWITCH_PS_ON "\xb9\xcb\xca\xb3"
#define MSG_SWITCH_PS_OFF "\xb9\xcb\xb5\xb6"

View File

@ -57,16 +57,16 @@
#define MSG_SET_HOME_OFFSETS "Nastavit ofsety"
#define MSG_HOME_OFFSETS_APPLIED "Ofsety nastaveny"
#define MSG_SET_ORIGIN "Nastavit pocatek"
#define MSG_PREHEAT_PLA "Zahrat PLA"
#define MSG_PREHEAT_PLA_N MSG_PREHEAT_PLA " "
#define MSG_PREHEAT_PLA_ALL MSG_PREHEAT_PLA " Vse"
#define MSG_PREHEAT_PLA_BEDONLY MSG_PREHEAT_PLA " Podloz"
#define MSG_PREHEAT_PLA_SETTINGS MSG_PREHEAT_PLA " Nast"
#define MSG_PREHEAT_ABS "Zahrat ABS"
#define MSG_PREHEAT_ABS_N MSG_PREHEAT_ABS " "
#define MSG_PREHEAT_ABS_ALL MSG_PREHEAT_ABS " Vse"
#define MSG_PREHEAT_ABS_BEDONLY MSG_PREHEAT_ABS " Podloz"
#define MSG_PREHEAT_ABS_SETTINGS MSG_PREHEAT_ABS " Nast"
#define MSG_PREHEAT_1 "Zahrat PLA"
#define MSG_PREHEAT_1_N MSG_PREHEAT_1 " "
#define MSG_PREHEAT_1_ALL MSG_PREHEAT_1 " Vse"
#define MSG_PREHEAT_1_BEDONLY MSG_PREHEAT_1 " Podloz"
#define MSG_PREHEAT_1_SETTINGS MSG_PREHEAT_1 " Nast"
#define MSG_PREHEAT_2 "Zahrat ABS"
#define MSG_PREHEAT_2_N MSG_PREHEAT_2 " "
#define MSG_PREHEAT_2_ALL MSG_PREHEAT_2 " Vse"
#define MSG_PREHEAT_2_BEDONLY MSG_PREHEAT_2 " Podloz"
#define MSG_PREHEAT_2_SETTINGS MSG_PREHEAT_2 " Nast"
#define MSG_H1 "1"
#define MSG_H2 "2"
#define MSG_H3 "3"

View File

@ -54,16 +54,16 @@
#define MSG_SET_HOME_OFFSETS "Sæt forskyding af home"
#define MSG_HOME_OFFSETS_APPLIED "Forskydninger af home pos. er tilføjet"
#define MSG_SET_ORIGIN "Sæt origin"
#define MSG_PREHEAT_PLA "Forvarm PLA"
#define MSG_PREHEAT_PLA_N "Forvarm PLA "
#define MSG_PREHEAT_PLA_ALL "Forvarm PLA Alle"
#define MSG_PREHEAT_PLA_BEDONLY "Forvarm PLA Bed"
#define MSG_PREHEAT_PLA_SETTINGS "Forvarm PLA conf"
#define MSG_PREHEAT_ABS "Forvarm ABS"
#define MSG_PREHEAT_ABS_N "Forvarm ABS "
#define MSG_PREHEAT_ABS_ALL "Forvarm ABS Alle"
#define MSG_PREHEAT_ABS_BEDONLY "Forvarm ABS Bed"
#define MSG_PREHEAT_ABS_SETTINGS "Forvarm ABS conf"
#define MSG_PREHEAT_1 "Forvarm PLA"
#define MSG_PREHEAT_1_N "Forvarm PLA "
#define MSG_PREHEAT_1_ALL "Forvarm PLA Alle"
#define MSG_PREHEAT_1_BEDONLY "Forvarm PLA Bed"
#define MSG_PREHEAT_1_SETTINGS "Forvarm PLA conf"
#define MSG_PREHEAT_2 "Forvarm ABS"
#define MSG_PREHEAT_2_N "Forvarm ABS "
#define MSG_PREHEAT_2_ALL "Forvarm ABS Alle"
#define MSG_PREHEAT_2_BEDONLY "Forvarm ABS Bed"
#define MSG_PREHEAT_2_SETTINGS "Forvarm ABS conf"
#define MSG_H1 "1"
#define MSG_H2 "2"
#define MSG_H3 "3"

View File

@ -49,16 +49,16 @@
#define MSG_SET_HOME_OFFSETS "Setze Homeoffsets"
#define MSG_HOME_OFFSETS_APPLIED "Offsets aktiv"
#define MSG_SET_ORIGIN "Setze Nullpunkt" //"G92 X0 Y0 Z0" commented out in ultralcd.cpp
#define MSG_PREHEAT_PLA "Vorwärmen PLA"
#define MSG_PREHEAT_PLA_N "Vorwärmen PLA "
#define MSG_PREHEAT_PLA_ALL "Vorw. PLA Alle"
#define MSG_PREHEAT_PLA_BEDONLY "Vorw. PLA Bett"
#define MSG_PREHEAT_PLA_SETTINGS "Vorw. PLA Einst."
#define MSG_PREHEAT_ABS "Vorwärmen ABS"
#define MSG_PREHEAT_ABS_N "Vorwärmen ABS "
#define MSG_PREHEAT_ABS_ALL "Vorw. ABS Alle"
#define MSG_PREHEAT_ABS_BEDONLY "Vorw. ABS Bett"
#define MSG_PREHEAT_ABS_SETTINGS "Vorw. ABS Einst."
#define MSG_PREHEAT_1 "Vorwärmen PLA"
#define MSG_PREHEAT_1_N "Vorwärmen PLA "
#define MSG_PREHEAT_1_ALL "Vorw. PLA Alle"
#define MSG_PREHEAT_1_BEDONLY "Vorw. PLA Bett"
#define MSG_PREHEAT_1_SETTINGS "Vorw. PLA Einst."
#define MSG_PREHEAT_2 "Vorwärmen ABS"
#define MSG_PREHEAT_2_N "Vorwärmen ABS "
#define MSG_PREHEAT_2_ALL "Vorw. ABS Alle"
#define MSG_PREHEAT_2_BEDONLY "Vorw. ABS Bett"
#define MSG_PREHEAT_2_SETTINGS "Vorw. ABS Einst."
#define MSG_COOLDOWN "Abkühlen"
#define MSG_SWITCH_PS_ON "Netzteil ein"
#define MSG_SWITCH_PS_OFF "Netzteil aus"

View File

@ -92,35 +92,35 @@
#ifndef MSG_SET_ORIGIN
#define MSG_SET_ORIGIN "Set origin"
#endif
#ifndef MSG_PREHEAT_PLA
#define MSG_PREHEAT_PLA "Preheat PLA"
#ifndef MSG_PREHEAT_1
#define MSG_PREHEAT_1 "Preheat PLA"
#endif
#ifndef MSG_PREHEAT_PLA_N
#define MSG_PREHEAT_PLA_N MSG_PREHEAT_PLA " "
#ifndef MSG_PREHEAT_1_N
#define MSG_PREHEAT_1_N MSG_PREHEAT_1 " "
#endif
#ifndef MSG_PREHEAT_PLA_ALL
#define MSG_PREHEAT_PLA_ALL MSG_PREHEAT_PLA " All"
#ifndef MSG_PREHEAT_1_ALL
#define MSG_PREHEAT_1_ALL MSG_PREHEAT_1 " All"
#endif
#ifndef MSG_PREHEAT_PLA_BEDONLY
#define MSG_PREHEAT_PLA_BEDONLY MSG_PREHEAT_PLA " Bed"
#ifndef MSG_PREHEAT_1_BEDONLY
#define MSG_PREHEAT_1_BEDONLY MSG_PREHEAT_1 " Bed"
#endif
#ifndef MSG_PREHEAT_PLA_SETTINGS
#define MSG_PREHEAT_PLA_SETTINGS MSG_PREHEAT_PLA " conf"
#ifndef MSG_PREHEAT_1_SETTINGS
#define MSG_PREHEAT_1_SETTINGS MSG_PREHEAT_1 " conf"
#endif
#ifndef MSG_PREHEAT_ABS
#define MSG_PREHEAT_ABS "Preheat ABS"
#ifndef MSG_PREHEAT_2
#define MSG_PREHEAT_2 "Preheat ABS"
#endif
#ifndef MSG_PREHEAT_ABS_N
#define MSG_PREHEAT_ABS_N MSG_PREHEAT_ABS " "
#ifndef MSG_PREHEAT_2_N
#define MSG_PREHEAT_2_N MSG_PREHEAT_2 " "
#endif
#ifndef MSG_PREHEAT_ABS_ALL
#define MSG_PREHEAT_ABS_ALL MSG_PREHEAT_ABS " All"
#ifndef MSG_PREHEAT_2_ALL
#define MSG_PREHEAT_2_ALL MSG_PREHEAT_2 " All"
#endif
#ifndef MSG_PREHEAT_ABS_BEDONLY
#define MSG_PREHEAT_ABS_BEDONLY MSG_PREHEAT_ABS " Bed"
#ifndef MSG_PREHEAT_2_BEDONLY
#define MSG_PREHEAT_2_BEDONLY MSG_PREHEAT_2 " Bed"
#endif
#ifndef MSG_PREHEAT_ABS_SETTINGS
#define MSG_PREHEAT_ABS_SETTINGS MSG_PREHEAT_ABS " conf"
#ifndef MSG_PREHEAT_2_SETTINGS
#define MSG_PREHEAT_2_SETTINGS MSG_PREHEAT_2 " conf"
#endif
#ifndef MSG_H1
#define MSG_H1 "1"

View File

@ -52,16 +52,16 @@
#define MSG_SET_HOME_OFFSETS "Ajustar desfases"
#define MSG_HOME_OFFSETS_APPLIED "Desfase aplicado"
#define MSG_SET_ORIGIN "Establecer origen"
#define MSG_PREHEAT_PLA "Precalentar PLA"
#define MSG_PREHEAT_PLA_N MSG_PREHEAT_PLA " "
#define MSG_PREHEAT_PLA_ALL MSG_PREHEAT_PLA "Todo"
#define MSG_PREHEAT_PLA_BEDONLY MSG_PREHEAT_PLA"Plataforma"
#define MSG_PREHEAT_PLA_SETTINGS MSG_PREHEAT_PLA "Config"
#define MSG_PREHEAT_ABS "Precalentar ABS"
#define MSG_PREHEAT_ABS_N MSG_PREHEAT_ABS " "
#define MSG_PREHEAT_ABS_ALL MSG_PREHEAT_ABS "Todo"
#define MSG_PREHEAT_ABS_BEDONLY MSG_PREHEAT_ABS "Plataforma"
#define MSG_PREHEAT_ABS_SETTINGS MSG_PREHEAT_ABS "Config"
#define MSG_PREHEAT_1 "Precalentar PLA"
#define MSG_PREHEAT_1_N MSG_PREHEAT_1 " "
#define MSG_PREHEAT_1_ALL MSG_PREHEAT_1 "Todo"
#define MSG_PREHEAT_1_BEDONLY MSG_PREHEAT_1"Plataforma"
#define MSG_PREHEAT_1_SETTINGS MSG_PREHEAT_1 "Config"
#define MSG_PREHEAT_2 "Precalentar ABS"
#define MSG_PREHEAT_2_N MSG_PREHEAT_2 " "
#define MSG_PREHEAT_2_ALL MSG_PREHEAT_2 "Todo"
#define MSG_PREHEAT_2_BEDONLY MSG_PREHEAT_2 "Plataforma"
#define MSG_PREHEAT_2_SETTINGS MSG_PREHEAT_2 "Config"
#define MSG_H1 "1"
#define MSG_H2 "2"
#define MSG_H3 "3"

View File

@ -48,16 +48,16 @@
#define MSG_SET_HOME_OFFSETS "Set home offsets"
#define MSG_HOME_OFFSETS_APPLIED "Offsets applied"
#define MSG_SET_ORIGIN "Hasiera ipini"
#define MSG_PREHEAT_PLA "Aurreberotu PLA"
#define MSG_PREHEAT_PLA_N "Aurreberotu PLA "
#define MSG_PREHEAT_PLA_ALL "Berotu PLA Guztia"
#define MSG_PREHEAT_PLA_BEDONLY "Berotu PLA Ohea"
#define MSG_PREHEAT_PLA_SETTINGS "Berotu PLA Konfig"
#define MSG_PREHEAT_ABS "Aurreberotu ABS"
#define MSG_PREHEAT_ABS_N "Aurreberotu ABS "
#define MSG_PREHEAT_ABS_ALL "Berotu ABS Guztia"
#define MSG_PREHEAT_ABS_BEDONLY "Berotu ABS Ohea"
#define MSG_PREHEAT_ABS_SETTINGS "Berotu ABS Konfig"
#define MSG_PREHEAT_1 "Aurreberotu PLA"
#define MSG_PREHEAT_1_N "Aurreberotu PLA "
#define MSG_PREHEAT_1_ALL "Berotu PLA Guztia"
#define MSG_PREHEAT_1_BEDONLY "Berotu PLA Ohea"
#define MSG_PREHEAT_1_SETTINGS "Berotu PLA Konfig"
#define MSG_PREHEAT_2 "Aurreberotu ABS"
#define MSG_PREHEAT_2_N "Aurreberotu ABS "
#define MSG_PREHEAT_2_ALL "Berotu ABS Guztia"
#define MSG_PREHEAT_2_BEDONLY "Berotu ABS Ohea"
#define MSG_PREHEAT_2_SETTINGS "Berotu ABS Konfig"
#define MSG_COOLDOWN "Hoztu"
#define MSG_SWITCH_PS_ON "Energia piztu"
#define MSG_SWITCH_PS_OFF "Energia itzali"

View File

@ -49,16 +49,16 @@
#define MSG_SET_HOME_OFFSETS "Set home offsets"
#define MSG_HOME_OFFSETS_APPLIED "Offsets applied"
#define MSG_SET_ORIGIN "Aseta origo"
#define MSG_PREHEAT_PLA "Esilämmitä PLA"
#define MSG_PREHEAT_PLA_N "Esilämmitä PLA "
#define MSG_PREHEAT_PLA_ALL "Esilä. PLA Kaikki"
#define MSG_PREHEAT_PLA_BEDONLY "Esilä. PLA Alusta"
#define MSG_PREHEAT_PLA_SETTINGS "Esilämm. PLA konf"
#define MSG_PREHEAT_ABS "Esilämmitä ABS"
#define MSG_PREHEAT_ABS_N "Esilämmitä ABS "
#define MSG_PREHEAT_ABS_ALL "Esilä. ABS Kaikki"
#define MSG_PREHEAT_ABS_BEDONLY "Esilä. ABS Alusta"
#define MSG_PREHEAT_ABS_SETTINGS "Esilämm. ABS konf"
#define MSG_PREHEAT_1 "Esilämmitä PLA"
#define MSG_PREHEAT_1_N "Esilämmitä PLA "
#define MSG_PREHEAT_1_ALL "Esilä. PLA Kaikki"
#define MSG_PREHEAT_1_BEDONLY "Esilä. PLA Alusta"
#define MSG_PREHEAT_1_SETTINGS "Esilämm. PLA konf"
#define MSG_PREHEAT_2 "Esilämmitä ABS"
#define MSG_PREHEAT_2_N "Esilämmitä ABS "
#define MSG_PREHEAT_2_ALL "Esilä. ABS Kaikki"
#define MSG_PREHEAT_2_BEDONLY "Esilä. ABS Alusta"
#define MSG_PREHEAT_2_SETTINGS "Esilämm. ABS konf"
#define MSG_COOLDOWN "Jäähdytä"
#define MSG_SWITCH_PS_ON "Virta päälle"
#define MSG_SWITCH_PS_OFF "Virta pois"

View File

@ -48,16 +48,16 @@
#define MSG_SET_HOME_OFFSETS "Regler decal. origine"
#define MSG_HOME_OFFSETS_APPLIED "Decalages appliques"
#define MSG_SET_ORIGIN "Regler origine"
#define MSG_PREHEAT_PLA "Prechauffage PLA"
#define MSG_PREHEAT_PLA_N "Prechauff. PLA "
#define MSG_PREHEAT_PLA_ALL "Prech. PLA Tout"
#define MSG_PREHEAT_PLA_BEDONLY "Prech. PLA Plateau"
#define MSG_PREHEAT_PLA_SETTINGS "Regl. prech. PLA"
#define MSG_PREHEAT_ABS "Prechauffage ABS"
#define MSG_PREHEAT_ABS_N "Prechauff. ABS "
#define MSG_PREHEAT_ABS_ALL "Prech. ABS Tout"
#define MSG_PREHEAT_ABS_BEDONLY "Prech. ABS Plateau"
#define MSG_PREHEAT_ABS_SETTINGS "Regl. prech. ABS"
#define MSG_PREHEAT_1 "Prechauffage PLA"
#define MSG_PREHEAT_1_N "Prechauff. PLA "
#define MSG_PREHEAT_1_ALL "Prech. PLA Tout"
#define MSG_PREHEAT_1_BEDONLY "Prech. PLA Plateau"
#define MSG_PREHEAT_1_SETTINGS "Regl. prech. PLA"
#define MSG_PREHEAT_2 "Prechauffage ABS"
#define MSG_PREHEAT_2_N "Prechauff. ABS "
#define MSG_PREHEAT_2_ALL "Prech. ABS Tout"
#define MSG_PREHEAT_2_BEDONLY "Prech. ABS Plateau"
#define MSG_PREHEAT_2_SETTINGS "Regl. prech. ABS"
#define MSG_COOLDOWN "Refroidir"
#define MSG_SWITCH_PS_ON "Allumer alim."
#define MSG_SWITCH_PS_OFF "Eteindre alim."

View File

@ -54,16 +54,16 @@
#define MSG_SET_HOME_OFFSETS "Offsets na orixe"
#define MSG_HOME_OFFSETS_APPLIED "Offsets fixados"
#define MSG_SET_ORIGIN "Fixar orixe"
#define MSG_PREHEAT_PLA "Prequentar PLA"
#define MSG_PREHEAT_PLA_N "Prequentar PLA "
#define MSG_PREHEAT_PLA_ALL "Preque. PLA Todo"
#define MSG_PREHEAT_PLA_BEDONLY "Preque. PLA Cama"
#define MSG_PREHEAT_PLA_SETTINGS "Preque. PLA conf"
#define MSG_PREHEAT_ABS "Prequentar ABS"
#define MSG_PREHEAT_ABS_N "Prequentar ABS "
#define MSG_PREHEAT_ABS_ALL "Preque. ABS Todo"
#define MSG_PREHEAT_ABS_BEDONLY "Preque. ABS Cama"
#define MSG_PREHEAT_ABS_SETTINGS "Preque. ABS conf"
#define MSG_PREHEAT_1 "Prequentar PLA"
#define MSG_PREHEAT_1_N "Prequentar PLA "
#define MSG_PREHEAT_1_ALL "Preque. PLA Todo"
#define MSG_PREHEAT_1_BEDONLY "Preque. PLA Cama"
#define MSG_PREHEAT_1_SETTINGS "Preque. PLA conf"
#define MSG_PREHEAT_2 "Prequentar ABS"
#define MSG_PREHEAT_2_N "Prequentar ABS "
#define MSG_PREHEAT_2_ALL "Preque. ABS Todo"
#define MSG_PREHEAT_2_BEDONLY "Preque. ABS Cama"
#define MSG_PREHEAT_2_SETTINGS "Preque. ABS conf"
#define MSG_H1 "1"
#define MSG_H2 "2"
#define MSG_H3 "3"

View File

@ -54,16 +54,16 @@
#define MSG_SET_HOME_OFFSETS "Postavi home offsete"
#define MSG_HOME_OFFSETS_APPLIED "Offsets postavljeni"
#define MSG_SET_ORIGIN "Postavi ishodište"
#define MSG_PREHEAT_PLA "Predgrij PLA"
#define MSG_PREHEAT_PLA_N MSG_PREHEAT_PLA " "
#define MSG_PREHEAT_PLA_ALL MSG_PREHEAT_PLA " Sve"
#define MSG_PREHEAT_PLA_BEDONLY MSG_PREHEAT_PLA " Bed"
#define MSG_PREHEAT_PLA_SETTINGS MSG_PREHEAT_PLA " conf"
#define MSG_PREHEAT_ABS "Predgrij ABS"
#define MSG_PREHEAT_ABS_N MSG_PREHEAT_ABS " "
#define MSG_PREHEAT_ABS_ALL MSG_PREHEAT_ABS " Sve"
#define MSG_PREHEAT_ABS_BEDONLY MSG_PREHEAT_ABS " Bed"
#define MSG_PREHEAT_ABS_SETTINGS MSG_PREHEAT_ABS " conf"
#define MSG_PREHEAT_1 "Predgrij PLA"
#define MSG_PREHEAT_1_N MSG_PREHEAT_1 " "
#define MSG_PREHEAT_1_ALL MSG_PREHEAT_1 " Sve"
#define MSG_PREHEAT_1_BEDONLY MSG_PREHEAT_1 " Bed"
#define MSG_PREHEAT_1_SETTINGS MSG_PREHEAT_1 " conf"
#define MSG_PREHEAT_2 "Predgrij ABS"
#define MSG_PREHEAT_2_N MSG_PREHEAT_2 " "
#define MSG_PREHEAT_2_ALL MSG_PREHEAT_2 " Sve"
#define MSG_PREHEAT_2_BEDONLY MSG_PREHEAT_2 " Bed"
#define MSG_PREHEAT_2_SETTINGS MSG_PREHEAT_2 " conf"
#define MSG_H1 "1"
#define MSG_H2 "2"
#define MSG_H3 "3"

View File

@ -53,16 +53,16 @@
#define MSG_SET_HOME_OFFSETS "Imp. offset home"
#define MSG_HOME_OFFSETS_APPLIED "Offset applicato"
#define MSG_SET_ORIGIN "Imposta Origine"
#define MSG_PREHEAT_PLA "Preriscalda PLA"
#define MSG_PREHEAT_PLA_N MSG_PREHEAT_PLA " "
#define MSG_PREHEAT_PLA_ALL MSG_PREHEAT_PLA " Tutto"
#define MSG_PREHEAT_PLA_BEDONLY MSG_PREHEAT_PLA " Piatto"
#define MSG_PREHEAT_PLA_SETTINGS MSG_PREHEAT_PLA " conf"
#define MSG_PREHEAT_ABS "Preriscalda ABS"
#define MSG_PREHEAT_ABS_N MSG_PREHEAT_ABS " "
#define MSG_PREHEAT_ABS_ALL MSG_PREHEAT_ABS " Tutto"
#define MSG_PREHEAT_ABS_BEDONLY MSG_PREHEAT_ABS " Piatto"
#define MSG_PREHEAT_ABS_SETTINGS MSG_PREHEAT_ABS " conf"
#define MSG_PREHEAT_1 "Preriscalda PLA"
#define MSG_PREHEAT_1_N MSG_PREHEAT_1 " "
#define MSG_PREHEAT_1_ALL MSG_PREHEAT_1 " Tutto"
#define MSG_PREHEAT_1_BEDONLY MSG_PREHEAT_1 " Piatto"
#define MSG_PREHEAT_1_SETTINGS MSG_PREHEAT_1 " conf"
#define MSG_PREHEAT_2 "Preriscalda ABS"
#define MSG_PREHEAT_2_N MSG_PREHEAT_2 " "
#define MSG_PREHEAT_2_ALL MSG_PREHEAT_2 " Tutto"
#define MSG_PREHEAT_2_BEDONLY MSG_PREHEAT_2 " Piatto"
#define MSG_PREHEAT_2_SETTINGS MSG_PREHEAT_2 " conf"
#define MSG_COOLDOWN "Raffredda"
#define MSG_SWITCH_PS_ON "Accendi aliment."
#define MSG_SWITCH_PS_OFF "Spegni aliment."

View File

@ -55,16 +55,16 @@
#define MSG_SET_HOME_OFFSETS "\xb7\xbc\xde\xad\xdd\xb5\xcc\xbe\xaf\xc4\xbe\xaf\xc3\xb2" // "キジュンオフセットセッテイ" ("Set home offsets")
#define MSG_HOME_OFFSETS_APPLIED "\xb5\xcc\xbe\xaf\xc4\xb6\xde\xc3\xb7\xd6\xb3\xbb\xda\xcf\xbc\xc0" // "オフセットガテキヨウサレマシタ" ("Offsets applied")
#define MSG_SET_ORIGIN "\xb7\xbc\xde\xad\xdd\xbe\xaf\xc4" // "キジュンセット" ("Set origin")
#define MSG_PREHEAT_PLA "PLA \xd6\xc8\xc2" // "PLA ヨネツ" ("Preheat PLA")
#define MSG_PREHEAT_PLA_N MSG_PREHEAT_PLA " "
#define MSG_PREHEAT_PLA_ALL MSG_PREHEAT_PLA " \xbd\xcd\xde\xc3" // " スベテ" (" All")
#define MSG_PREHEAT_PLA_BEDONLY MSG_PREHEAT_PLA " \xcd\xde\xaf\xc4\xde" // " ベッド" (" Bed")
#define MSG_PREHEAT_PLA_SETTINGS MSG_PREHEAT_PLA " \xbe\xaf\xc3\xb2" // " セッテイ" (" conf")
#define MSG_PREHEAT_ABS "ABS \xd6\xc8\xc2" // "ABS ヨネツ" ("Preheat ABS")
#define MSG_PREHEAT_ABS_N MSG_PREHEAT_ABS " "
#define MSG_PREHEAT_ABS_ALL MSG_PREHEAT_ABS " \xbd\xcd\xde\xc3" // " スベテ" (" All")
#define MSG_PREHEAT_ABS_BEDONLY MSG_PREHEAT_ABS " \xcd\xde\xaf\xc4\xde" // " ベッド" (" Bed")
#define MSG_PREHEAT_ABS_SETTINGS MSG_PREHEAT_ABS " \xbe\xaf\xc3\xb2" // " セッテイ" (" conf")
#define MSG_PREHEAT_1 "PLA \xd6\xc8\xc2" // "PLA ヨネツ" ("Preheat PLA")
#define MSG_PREHEAT_1_N MSG_PREHEAT_1 " "
#define MSG_PREHEAT_1_ALL MSG_PREHEAT_1 " \xbd\xcd\xde\xc3" // " スベテ" (" All")
#define MSG_PREHEAT_1_BEDONLY MSG_PREHEAT_1 " \xcd\xde\xaf\xc4\xde" // " ベッド" (" Bed")
#define MSG_PREHEAT_1_SETTINGS MSG_PREHEAT_1 " \xbe\xaf\xc3\xb2" // " セッテイ" (" conf")
#define MSG_PREHEAT_2 "ABS \xd6\xc8\xc2" // "ABS ヨネツ" ("Preheat ABS")
#define MSG_PREHEAT_2_N MSG_PREHEAT_2 " "
#define MSG_PREHEAT_2_ALL MSG_PREHEAT_2 " \xbd\xcd\xde\xc3" // " スベテ" (" All")
#define MSG_PREHEAT_2_BEDONLY MSG_PREHEAT_2 " \xcd\xde\xaf\xc4\xde" // " ベッド" (" Bed")
#define MSG_PREHEAT_2_SETTINGS MSG_PREHEAT_2 " \xbe\xaf\xc3\xb2" // " セッテイ" (" conf")
#define MSG_COOLDOWN "\xb6\xc8\xc2\xc3\xb2\xbc" // "カネツテイシ" ("Cooldown")
#define MSG_SWITCH_PS_ON "\xc3\xde\xdd\xb9\xde\xdd\x20\xb5\xdd" // "デンゲン オン" ("Switch power on")
#define MSG_SWITCH_PS_OFF "\xc3\xde\xdd\xb9\xde\xdd\x20\xb5\xcc" // "デンゲン オフ" ("Switch power off")

View File

@ -59,16 +59,16 @@
#define MSG_SET_HOME_OFFSETS "キジュンオフセットセッテイ" // "Set home offsets"
#define MSG_HOME_OFFSETS_APPLIED "オフセットガテキヨウサレマシタ" // "Offsets applied"
#define MSG_SET_ORIGIN "キジュンセット" // "Set origin"
#define MSG_PREHEAT_PLA "PLA ヨネツ" // "Preheat PLA"
#define MSG_PREHEAT_PLA_N MSG_PREHEAT_PLA " "
#define MSG_PREHEAT_PLA_ALL MSG_PREHEAT_PLA " スベテ" // " All"
#define MSG_PREHEAT_PLA_BEDONLY MSG_PREHEAT_PLA " ベッド" // " Bed"
#define MSG_PREHEAT_PLA_SETTINGS MSG_PREHEAT_PLA " セッテイ" // " conf"
#define MSG_PREHEAT_ABS "ABS ヨネツ" // "Preheat ABS"
#define MSG_PREHEAT_ABS_N MSG_PREHEAT_ABS " "
#define MSG_PREHEAT_ABS_ALL MSG_PREHEAT_ABS " スベテ" // " All"
#define MSG_PREHEAT_ABS_BEDONLY MSG_PREHEAT_ABS " ベッド" // " Bed"
#define MSG_PREHEAT_ABS_SETTINGS MSG_PREHEAT_ABS " セッテイ" // " conf"
#define MSG_PREHEAT_1 "PLA ヨネツ" // "Preheat PLA"
#define MSG_PREHEAT_1_N MSG_PREHEAT_1 " "
#define MSG_PREHEAT_1_ALL MSG_PREHEAT_1 " スベテ" // " All"
#define MSG_PREHEAT_1_BEDONLY MSG_PREHEAT_1 " ベッド" // " Bed"
#define MSG_PREHEAT_1_SETTINGS MSG_PREHEAT_1 " セッテイ" // " conf"
#define MSG_PREHEAT_2 "ABS ヨネツ" // "Preheat ABS"
#define MSG_PREHEAT_2_N MSG_PREHEAT_2 " "
#define MSG_PREHEAT_2_ALL MSG_PREHEAT_2 " スベテ" // " All"
#define MSG_PREHEAT_2_BEDONLY MSG_PREHEAT_2 " ベッド" // " Bed"
#define MSG_PREHEAT_2_SETTINGS MSG_PREHEAT_2 " セッテイ" // " conf"
#define MSG_COOLDOWN "カネツテイシ" // "Cooldown"
#define MSG_SWITCH_PS_ON "デンゲン オン" // "Switch power on"
#define MSG_SWITCH_PS_OFF "デンゲン オフ" // "Switch power off"

View File

@ -48,16 +48,16 @@
#define MSG_SET_HOME_OFFSETS "Zet home offsets"
#define MSG_HOME_OFFSETS_APPLIED "H offset toegep."
#define MSG_SET_ORIGIN "Nulpunt instellen"
#define MSG_PREHEAT_PLA "PLA voorverwarmen"
#define MSG_PREHEAT_PLA_N "PLA voorverw. "
#define MSG_PREHEAT_PLA_ALL "PLA voorverw. aan"
#define MSG_PREHEAT_PLA_BEDONLY "PLA voorverw. Bed"
#define MSG_PREHEAT_PLA_SETTINGS "PLA verw. conf"
#define MSG_PREHEAT_ABS "ABS voorverwarmen"
#define MSG_PREHEAT_ABS_N "ABS voorverw. "
#define MSG_PREHEAT_ABS_ALL "ABS voorverw. aan"
#define MSG_PREHEAT_ABS_BEDONLY "ABS voorverw. Bed"
#define MSG_PREHEAT_ABS_SETTINGS "ABS verw. conf"
#define MSG_PREHEAT_1 "PLA voorverwarmen"
#define MSG_PREHEAT_1_N "PLA voorverw. "
#define MSG_PREHEAT_1_ALL "PLA voorverw. aan"
#define MSG_PREHEAT_1_BEDONLY "PLA voorverw. Bed"
#define MSG_PREHEAT_1_SETTINGS "PLA verw. conf"
#define MSG_PREHEAT_2 "ABS voorverwarmen"
#define MSG_PREHEAT_2_N "ABS voorverw. "
#define MSG_PREHEAT_2_ALL "ABS voorverw. aan"
#define MSG_PREHEAT_2_BEDONLY "ABS voorverw. Bed"
#define MSG_PREHEAT_2_SETTINGS "ABS verw. conf"
#define MSG_COOLDOWN "Afkoelen"
#define MSG_SWITCH_PS_ON "Stroom aan"
#define MSG_SWITCH_PS_OFF "Stroom uit"

View File

@ -50,16 +50,16 @@
#define MSG_SET_HOME_OFFSETS "Ust. poz. zer."
#define MSG_HOME_OFFSETS_APPLIED "Poz. zerowa ust."
#define MSG_SET_ORIGIN "Ustaw punkt zero"
#define MSG_PREHEAT_PLA "Rozgrzej PLA"
#define MSG_PREHEAT_PLA_N "Rozgrzej PLA "
#define MSG_PREHEAT_PLA_ALL "Roz. PLA Wszystko"
#define MSG_PREHEAT_PLA_BEDONLY "Rozgrzej PLA Loze"
#define MSG_PREHEAT_PLA_SETTINGS "Ustaw. rozg. PLA"
#define MSG_PREHEAT_ABS "Rozgrzej ABS"
#define MSG_PREHEAT_ABS_N "Rozgrzej ABS "
#define MSG_PREHEAT_ABS_ALL "Roz. ABS Wszystko"
#define MSG_PREHEAT_ABS_BEDONLY "Rozgrzej ABS Loze"
#define MSG_PREHEAT_ABS_SETTINGS "Ustaw. rozg. ABS"
#define MSG_PREHEAT_1 "Rozgrzej PLA"
#define MSG_PREHEAT_1_N "Rozgrzej PLA "
#define MSG_PREHEAT_1_ALL "Roz. PLA Wszystko"
#define MSG_PREHEAT_1_BEDONLY "Rozgrzej PLA Loze"
#define MSG_PREHEAT_1_SETTINGS "Ustaw. rozg. PLA"
#define MSG_PREHEAT_2 "Rozgrzej ABS"
#define MSG_PREHEAT_2_N "Rozgrzej ABS "
#define MSG_PREHEAT_2_ALL "Roz. ABS Wszystko"
#define MSG_PREHEAT_2_BEDONLY "Rozgrzej ABS Loze"
#define MSG_PREHEAT_2_SETTINGS "Ustaw. rozg. ABS"
#define MSG_H1 "1"
#define MSG_H2 "2"
#define MSG_H3 "3"

View File

@ -48,16 +48,16 @@
#define MSG_SET_HOME_OFFSETS "Ajustar Jogo"
#define MSG_HOME_OFFSETS_APPLIED "Offsets applied"
#define MSG_SET_ORIGIN "Ajustar orig."
#define MSG_PREHEAT_PLA "Pre-aquecer PLA"
#define MSG_PREHEAT_PLA_N "Pre-aquecer PLA"
#define MSG_PREHEAT_PLA_ALL "Pre-aq.Todo PLA"
#define MSG_PREHEAT_PLA_BEDONLY "Pre-aq. PLA " LCD_STR_THERMOMETER "Base"
#define MSG_PREHEAT_PLA_SETTINGS "Ajustar PLA"
#define MSG_PREHEAT_ABS "Pre-aquecer ABS"
#define MSG_PREHEAT_ABS_N "Pre-aquecer ABS"
#define MSG_PREHEAT_ABS_ALL "Pre-aq.Todo ABS"
#define MSG_PREHEAT_ABS_BEDONLY "Pre-aq. ABS " LCD_STR_THERMOMETER "Base"
#define MSG_PREHEAT_ABS_SETTINGS "Ajustar ABS"
#define MSG_PREHEAT_1 "Pre-aquecer PLA"
#define MSG_PREHEAT_1_N "Pre-aquecer PLA"
#define MSG_PREHEAT_1_ALL "Pre-aq.Todo PLA"
#define MSG_PREHEAT_1_BEDONLY "Pre-aq. PLA " LCD_STR_THERMOMETER "Base"
#define MSG_PREHEAT_1_SETTINGS "Ajustar PLA"
#define MSG_PREHEAT_2 "Pre-aquecer ABS"
#define MSG_PREHEAT_2_N "Pre-aquecer ABS"
#define MSG_PREHEAT_2_ALL "Pre-aq.Todo ABS"
#define MSG_PREHEAT_2_BEDONLY "Pre-aq. ABS " LCD_STR_THERMOMETER "Base"
#define MSG_PREHEAT_2_SETTINGS "Ajustar ABS"
#define MSG_COOLDOWN "Esfriar"
#define MSG_SWITCH_PS_ON "Ligar"
#define MSG_SWITCH_PS_OFF "Desligar"

View File

@ -48,16 +48,16 @@
#define MSG_SET_HOME_OFFSETS "Ajustar Jogo"
#define MSG_HOME_OFFSETS_APPLIED "Offsets applied"
#define MSG_SET_ORIGIN "Ajustar orig."
#define MSG_PREHEAT_PLA "Pre-aquecer PLA"
#define MSG_PREHEAT_PLA_N "Pre-aquecer PLA"
#define MSG_PREHEAT_PLA_ALL "Pre-aq.Todo PLA"
#define MSG_PREHEAT_PLA_BEDONLY "Pre-aq. PLA " LCD_STR_THERMOMETER "Base"
#define MSG_PREHEAT_PLA_SETTINGS "Ajustar PLA"
#define MSG_PREHEAT_ABS "Pre-aquecer ABS"
#define MSG_PREHEAT_ABS_N "Pre-aquecer ABS"
#define MSG_PREHEAT_ABS_ALL "Pre-aq.Todo ABS"
#define MSG_PREHEAT_ABS_BEDONLY "Pre-aq. ABS " LCD_STR_THERMOMETER "Base"
#define MSG_PREHEAT_ABS_SETTINGS "Ajustar ABS"
#define MSG_PREHEAT_1 "Pre-aquecer PLA"
#define MSG_PREHEAT_1_N "Pre-aquecer PLA"
#define MSG_PREHEAT_1_ALL "Pre-aq.Todo PLA"
#define MSG_PREHEAT_1_BEDONLY "Pre-aq. PLA " LCD_STR_THERMOMETER "Base"
#define MSG_PREHEAT_1_SETTINGS "Ajustar PLA"
#define MSG_PREHEAT_2 "Pre-aquecer ABS"
#define MSG_PREHEAT_2_N "Pre-aquecer ABS"
#define MSG_PREHEAT_2_ALL "Pre-aq.Todo ABS"
#define MSG_PREHEAT_2_BEDONLY "Pre-aq. ABS " LCD_STR_THERMOMETER "Base"
#define MSG_PREHEAT_2_SETTINGS "Ajustar ABS"
#define MSG_COOLDOWN "Esfriar"
#define MSG_SWITCH_PS_ON "Ligar"
#define MSG_SWITCH_PS_OFF "Desligar"

View File

@ -52,16 +52,16 @@
#define MSG_SET_HOME_OFFSETS "Definir desvio"
#define MSG_HOME_OFFSETS_APPLIED "Offsets applied"
#define MSG_SET_ORIGIN "Definir origem"
#define MSG_PREHEAT_PLA "Pre-aquecer PLA"
#define MSG_PREHEAT_PLA_N "Pre-aquecer PLA"
#define MSG_PREHEAT_PLA_ALL "Pre-aq. PLA Tudo"
#define MSG_PREHEAT_PLA_BEDONLY "Pre-aq. PLA " LCD_STR_THERMOMETER "Base"
#define MSG_PREHEAT_PLA_SETTINGS "Definicoes PLA"
#define MSG_PREHEAT_ABS "Pre-aquecer ABS"
#define MSG_PREHEAT_ABS_N "Pre-aquecer ABS "
#define MSG_PREHEAT_ABS_ALL "Pre-aq. ABS Tudo"
#define MSG_PREHEAT_ABS_BEDONLY "Pre-aq. ABS " LCD_STR_THERMOMETER "Base"
#define MSG_PREHEAT_ABS_SETTINGS "Definicoes ABS"
#define MSG_PREHEAT_1 "Pre-aquecer PLA"
#define MSG_PREHEAT_1_N "Pre-aquecer PLA"
#define MSG_PREHEAT_1_ALL "Pre-aq. PLA Tudo"
#define MSG_PREHEAT_1_BEDONLY "Pre-aq. PLA " LCD_STR_THERMOMETER "Base"
#define MSG_PREHEAT_1_SETTINGS "Definicoes PLA"
#define MSG_PREHEAT_2 "Pre-aquecer ABS"
#define MSG_PREHEAT_2_N "Pre-aquecer ABS "
#define MSG_PREHEAT_2_ALL "Pre-aq. ABS Tudo"
#define MSG_PREHEAT_2_BEDONLY "Pre-aq. ABS " LCD_STR_THERMOMETER "Base"
#define MSG_PREHEAT_2_SETTINGS "Definicoes ABS"
#define MSG_COOLDOWN "Arrefecer"
#define MSG_SWITCH_PS_ON "Ligar"
#define MSG_SWITCH_PS_OFF "Desligar"

View File

@ -52,16 +52,16 @@
#define MSG_SET_HOME_OFFSETS "Definir desvio"
#define MSG_HOME_OFFSETS_APPLIED "Offsets aplicados"
#define MSG_SET_ORIGIN "Definir origem"
#define MSG_PREHEAT_PLA "Pre-aquecer PLA"
#define MSG_PREHEAT_PLA_N "Pre-aquecer PLA"
#define MSG_PREHEAT_PLA_ALL "Pre-aq. PLA Tudo"
#define MSG_PREHEAT_PLA_BEDONLY "Pre-aq. PLA " LCD_STR_THERMOMETER "Base"
#define MSG_PREHEAT_PLA_SETTINGS "Definições PLA"
#define MSG_PREHEAT_ABS "Pre-aquecer ABS"
#define MSG_PREHEAT_ABS_N "Pre-aquecer ABS "
#define MSG_PREHEAT_ABS_ALL "Pre-aq. ABS Tudo"
#define MSG_PREHEAT_ABS_BEDONLY "Pre-aq. ABS " LCD_STR_THERMOMETER "Base"
#define MSG_PREHEAT_ABS_SETTINGS "Definições ABS"
#define MSG_PREHEAT_1 "Pre-aquecer PLA"
#define MSG_PREHEAT_1_N "Pre-aquecer PLA"
#define MSG_PREHEAT_1_ALL "Pre-aq. PLA Tudo"
#define MSG_PREHEAT_1_BEDONLY "Pre-aq. PLA " LCD_STR_THERMOMETER "Base"
#define MSG_PREHEAT_1_SETTINGS "Definições PLA"
#define MSG_PREHEAT_2 "Pre-aquecer ABS"
#define MSG_PREHEAT_2_N "Pre-aquecer ABS "
#define MSG_PREHEAT_2_ALL "Pre-aq. ABS Tudo"
#define MSG_PREHEAT_2_BEDONLY "Pre-aq. ABS " LCD_STR_THERMOMETER "Base"
#define MSG_PREHEAT_2_SETTINGS "Definições ABS"
#define MSG_COOLDOWN "Arrefecer"
#define MSG_SWITCH_PS_ON "Ligar"
#define MSG_SWITCH_PS_OFF "Desligar"

View File

@ -49,16 +49,16 @@
#define MSG_SET_HOME_OFFSETS "Запомнить парковку"
#define MSG_HOME_OFFSETS_APPLIED "Offsets applied"
#define MSG_SET_ORIGIN "Запомнить ноль"
#define MSG_PREHEAT_PLA "Преднагрев PLA"
#define MSG_PREHEAT_PLA_N "Греть PLA Сопло "
#define MSG_PREHEAT_PLA_ALL "Греть PLA Все"
#define MSG_PREHEAT_PLA_BEDONLY "Греть PLA Стол"
#define MSG_PREHEAT_PLA_SETTINGS "Настройки PLA"
#define MSG_PREHEAT_ABS "Преднагрев ABS"
#define MSG_PREHEAT_ABS_N "Греть ABS Сопло "
#define MSG_PREHEAT_ABS_ALL "Греть ABS Все"
#define MSG_PREHEAT_ABS_BEDONLY "Греть ABS Стол"
#define MSG_PREHEAT_ABS_SETTINGS "Настройки ABS"
#define MSG_PREHEAT_1 "Преднагрев PLA"
#define MSG_PREHEAT_1_N "Греть PLA Сопло "
#define MSG_PREHEAT_1_ALL "Греть PLA Все"
#define MSG_PREHEAT_1_BEDONLY "Греть PLA Стол"
#define MSG_PREHEAT_1_SETTINGS "Настройки PLA"
#define MSG_PREHEAT_2 "Преднагрев ABS"
#define MSG_PREHEAT_2_N "Греть ABS Сопло "
#define MSG_PREHEAT_2_ALL "Греть ABS Все"
#define MSG_PREHEAT_2_BEDONLY "Греть ABS Стол"
#define MSG_PREHEAT_2_SETTINGS "Настройки ABS"
#define MSG_COOLDOWN "Охлаждение"
#define MSG_SWITCH_PS_ON "Включить Питание"
#define MSG_SWITCH_PS_OFF "Отключить Питание"

View File

@ -141,8 +141,8 @@
#define MSG_DISABLE_STEPPERS STRG_C2_8
#define MSG_AUTO_HOME STRG_C2_9
#define MSG_SET_HOME_OFFSETS STRG_C2_a
#define MSG_PREHEAT_PLA STRG_C2_b
#define MSG_PREHEAT_ABS STRG_C3_8
#define MSG_PREHEAT_1 STRG_C2_b
#define MSG_PREHEAT_2 STRG_C3_8
#define MSG_COOLDOWN STRG_C3_9
#define MSG_SWITCH_PS_OFF STRG_C3_a
#define MSG_MOVE_AXIS STRG_C3_b
@ -176,8 +176,8 @@
#define MSG_DISABLE_STEPPERS STRG_D0_8
#define MSG_AUTO_HOME STRG_D0_9
#define MSG_SET_HOME_OFFSETS STRG_D0_a
#define MSG_PREHEAT_PLA STRG_D0_b
#define MSG_PREHEAT_ABS STRG_D1_8
#define MSG_PREHEAT_1 STRG_D0_b
#define MSG_PREHEAT_2 STRG_D1_8
#define MSG_COOLDOWN STRG_D1_9
#define MSG_SWITCH_PS_OFF STRG_D1_a
#define MSG_MOVE_AXIS STRG_D1_b
@ -211,8 +211,8 @@
#define MSG_DISABLE_STEPPERS STRG_E382_8
#define MSG_AUTO_HOME STRG_E382_9
#define MSG_SET_HOME_OFFSETS STRG_E382_a
#define MSG_PREHEAT_PLA STRG_E382_b
#define MSG_PREHEAT_ABS STRG_E383_8
#define MSG_PREHEAT_1 STRG_E382_b
#define MSG_PREHEAT_2 STRG_E383_8
#define MSG_COOLDOWN STRG_E383_9
#define MSG_SWITCH_PS_OFF STRG_E383_a
#define MSG_MOVE_AXIS STRG_E383_b

View File

@ -33,13 +33,8 @@
#include "printcounter.h"
#endif
int plaPreheatHotendTemp;
int plaPreheatHPBTemp;
int plaPreheatFanSpeed;
int absPreheatHotendTemp;
int absPreheatHPBTemp;
int absPreheatFanSpeed;
int preheatHotendTemp1, preheatBedTemp1, preheatFanSpeed1,
preheatHotendTemp2, preheatBedTemp2, preheatFanSpeed2;
#if ENABLED(FILAMENT_LCD_DISPLAY)
millis_t previous_lcd_status_ms = 0;
@ -885,29 +880,29 @@ void kill_screen(const char* lcd_msg) {
}
#if TEMP_SENSOR_0 != 0
void lcd_preheat_pla0() { _lcd_preheat(0, plaPreheatHotendTemp, plaPreheatHPBTemp, plaPreheatFanSpeed); }
void lcd_preheat_abs0() { _lcd_preheat(0, absPreheatHotendTemp, absPreheatHPBTemp, absPreheatFanSpeed); }
void lcd_preheat_pla0() { _lcd_preheat(0, preheatHotendTemp1, preheatBedTemp1, preheatFanSpeed1); }
void lcd_preheat_abs0() { _lcd_preheat(0, preheatHotendTemp2, preheatBedTemp2, preheatFanSpeed2); }
#endif
#if HOTENDS > 1
void lcd_preheat_pla1() { _lcd_preheat(1, plaPreheatHotendTemp, plaPreheatHPBTemp, plaPreheatFanSpeed); }
void lcd_preheat_abs1() { _lcd_preheat(1, absPreheatHotendTemp, absPreheatHPBTemp, absPreheatFanSpeed); }
void lcd_preheat_pla1() { _lcd_preheat(1, preheatHotendTemp1, preheatBedTemp1, preheatFanSpeed1); }
void lcd_preheat_abs1() { _lcd_preheat(1, preheatHotendTemp2, preheatBedTemp2, preheatFanSpeed2); }
#if HOTENDS > 2
void lcd_preheat_pla2() { _lcd_preheat(2, plaPreheatHotendTemp, plaPreheatHPBTemp, plaPreheatFanSpeed); }
void lcd_preheat_abs2() { _lcd_preheat(2, absPreheatHotendTemp, absPreheatHPBTemp, absPreheatFanSpeed); }
void lcd_preheat_pla2() { _lcd_preheat(2, preheatHotendTemp1, preheatBedTemp1, preheatFanSpeed1); }
void lcd_preheat_abs2() { _lcd_preheat(2, preheatHotendTemp2, preheatBedTemp2, preheatFanSpeed2); }
#if HOTENDS > 3
void lcd_preheat_pla3() { _lcd_preheat(3, plaPreheatHotendTemp, plaPreheatHPBTemp, plaPreheatFanSpeed); }
void lcd_preheat_abs3() { _lcd_preheat(3, absPreheatHotendTemp, absPreheatHPBTemp, absPreheatFanSpeed); }
void lcd_preheat_pla3() { _lcd_preheat(3, preheatHotendTemp1, preheatBedTemp1, preheatFanSpeed1); }
void lcd_preheat_abs3() { _lcd_preheat(3, preheatHotendTemp2, preheatBedTemp2, preheatFanSpeed2); }
#endif
#endif
void lcd_preheat_pla0123() {
#if HOTENDS > 1
thermalManager.setTargetHotend(plaPreheatHotendTemp, 1);
thermalManager.setTargetHotend(preheatHotendTemp1, 1);
#if HOTENDS > 2
thermalManager.setTargetHotend(plaPreheatHotendTemp, 2);
thermalManager.setTargetHotend(preheatHotendTemp1, 2);
#if HOTENDS > 3
thermalManager.setTargetHotend(plaPreheatHotendTemp, 3);
thermalManager.setTargetHotend(preheatHotendTemp1, 3);
#endif
#endif
#endif
@ -915,11 +910,11 @@ void kill_screen(const char* lcd_msg) {
}
void lcd_preheat_abs0123() {
#if HOTENDS > 1
thermalManager.setTargetHotend(absPreheatHotendTemp, 1);
thermalManager.setTargetHotend(preheatHotendTemp2, 1);
#if HOTENDS > 2
thermalManager.setTargetHotend(absPreheatHotendTemp, 2);
thermalManager.setTargetHotend(preheatHotendTemp2, 2);
#if HOTENDS > 3
thermalManager.setTargetHotend(absPreheatHotendTemp, 3);
thermalManager.setTargetHotend(preheatHotendTemp2, 3);
#endif
#endif
#endif
@ -929,8 +924,8 @@ void kill_screen(const char* lcd_msg) {
#endif // HOTENDS > 1
#if TEMP_SENSOR_BED != 0
void lcd_preheat_pla_bedonly() { _lcd_preheat(0, 0, plaPreheatHPBTemp, plaPreheatFanSpeed); }
void lcd_preheat_abs_bedonly() { _lcd_preheat(0, 0, absPreheatHPBTemp, absPreheatFanSpeed); }
void lcd_preheat_pla_bedonly() { _lcd_preheat(0, 0, preheatBedTemp1, preheatFanSpeed1); }
void lcd_preheat_abs_bedonly() { _lcd_preheat(0, 0, preheatBedTemp2, preheatFanSpeed2); }
#endif
#if TEMP_SENSOR_0 != 0 && (TEMP_SENSOR_1 != 0 || TEMP_SENSOR_2 != 0 || TEMP_SENSOR_3 != 0 || TEMP_SENSOR_BED != 0)
@ -939,20 +934,20 @@ void kill_screen(const char* lcd_msg) {
START_MENU();
MENU_ITEM(back, MSG_PREPARE);
#if HOTENDS == 1
MENU_ITEM(function, MSG_PREHEAT_PLA, lcd_preheat_pla0);
MENU_ITEM(function, MSG_PREHEAT_1, lcd_preheat_pla0);
#else
MENU_ITEM(function, MSG_PREHEAT_PLA_N MSG_H1, lcd_preheat_pla0);
MENU_ITEM(function, MSG_PREHEAT_PLA_N MSG_H2, lcd_preheat_pla1);
MENU_ITEM(function, MSG_PREHEAT_1_N MSG_H1, lcd_preheat_pla0);
MENU_ITEM(function, MSG_PREHEAT_1_N MSG_H2, lcd_preheat_pla1);
#if HOTENDS > 2
MENU_ITEM(function, MSG_PREHEAT_PLA_N MSG_H3, lcd_preheat_pla2);
MENU_ITEM(function, MSG_PREHEAT_1_N MSG_H3, lcd_preheat_pla2);
#if HOTENDS > 3
MENU_ITEM(function, MSG_PREHEAT_PLA_N MSG_H4, lcd_preheat_pla3);
MENU_ITEM(function, MSG_PREHEAT_1_N MSG_H4, lcd_preheat_pla3);
#endif
#endif
MENU_ITEM(function, MSG_PREHEAT_PLA_ALL, lcd_preheat_pla0123);
MENU_ITEM(function, MSG_PREHEAT_1_ALL, lcd_preheat_pla0123);
#endif
#if TEMP_SENSOR_BED != 0
MENU_ITEM(function, MSG_PREHEAT_PLA_BEDONLY, lcd_preheat_pla_bedonly);
MENU_ITEM(function, MSG_PREHEAT_1_BEDONLY, lcd_preheat_pla_bedonly);
#endif
END_MENU();
}
@ -961,20 +956,20 @@ void kill_screen(const char* lcd_msg) {
START_MENU();
MENU_ITEM(back, MSG_PREPARE);
#if HOTENDS == 1
MENU_ITEM(function, MSG_PREHEAT_ABS, lcd_preheat_abs0);
MENU_ITEM(function, MSG_PREHEAT_2, lcd_preheat_abs0);
#else
MENU_ITEM(function, MSG_PREHEAT_ABS_N MSG_H1, lcd_preheat_abs0);
MENU_ITEM(function, MSG_PREHEAT_ABS_N MSG_H2, lcd_preheat_abs1);
MENU_ITEM(function, MSG_PREHEAT_2_N MSG_H1, lcd_preheat_abs0);
MENU_ITEM(function, MSG_PREHEAT_2_N MSG_H2, lcd_preheat_abs1);
#if HOTENDS > 2
MENU_ITEM(function, MSG_PREHEAT_ABS_N MSG_H3, lcd_preheat_abs2);
MENU_ITEM(function, MSG_PREHEAT_2_N MSG_H3, lcd_preheat_abs2);
#if HOTENDS > 3
MENU_ITEM(function, MSG_PREHEAT_ABS_N MSG_H4, lcd_preheat_abs3);
MENU_ITEM(function, MSG_PREHEAT_2_N MSG_H4, lcd_preheat_abs3);
#endif
#endif
MENU_ITEM(function, MSG_PREHEAT_ABS_ALL, lcd_preheat_abs0123);
MENU_ITEM(function, MSG_PREHEAT_2_ALL, lcd_preheat_abs0123);
#endif
#if TEMP_SENSOR_BED != 0
MENU_ITEM(function, MSG_PREHEAT_ABS_BEDONLY, lcd_preheat_abs_bedonly);
MENU_ITEM(function, MSG_PREHEAT_2_BEDONLY, lcd_preheat_abs_bedonly);
#endif
END_MENU();
}
@ -1250,11 +1245,11 @@ void kill_screen(const char* lcd_msg) {
//
#if TEMP_SENSOR_0 != 0
#if TEMP_SENSOR_1 != 0 || TEMP_SENSOR_2 != 0 || TEMP_SENSOR_3 != 0 || TEMP_SENSOR_BED != 0
MENU_ITEM(submenu, MSG_PREHEAT_PLA, lcd_preheat_pla_menu);
MENU_ITEM(submenu, MSG_PREHEAT_ABS, lcd_preheat_abs_menu);
MENU_ITEM(submenu, MSG_PREHEAT_1, lcd_preheat_pla_menu);
MENU_ITEM(submenu, MSG_PREHEAT_2, lcd_preheat_abs_menu);
#else
MENU_ITEM(function, MSG_PREHEAT_PLA, lcd_preheat_pla0);
MENU_ITEM(function, MSG_PREHEAT_ABS, lcd_preheat_abs0);
MENU_ITEM(function, MSG_PREHEAT_1, lcd_preheat_pla0);
MENU_ITEM(function, MSG_PREHEAT_2, lcd_preheat_abs0);
#endif
#endif
@ -1713,12 +1708,12 @@ void kill_screen(const char* lcd_msg) {
//
// Preheat PLA conf
//
MENU_ITEM(submenu, MSG_PREHEAT_PLA_SETTINGS, lcd_control_temperature_preheat_pla_settings_menu);
MENU_ITEM(submenu, MSG_PREHEAT_1_SETTINGS, lcd_control_temperature_preheat_pla_settings_menu);
//
// Preheat ABS conf
//
MENU_ITEM(submenu, MSG_PREHEAT_ABS_SETTINGS, lcd_control_temperature_preheat_abs_settings_menu);
MENU_ITEM(submenu, MSG_PREHEAT_2_SETTINGS, lcd_control_temperature_preheat_abs_settings_menu);
END_MENU();
}
@ -1730,12 +1725,12 @@ void kill_screen(const char* lcd_msg) {
static void lcd_control_temperature_preheat_pla_settings_menu() {
START_MENU();
MENU_ITEM(back, MSG_TEMPERATURE);
MENU_ITEM_EDIT(int3, MSG_FAN_SPEED, &plaPreheatFanSpeed, 0, 255);
MENU_ITEM_EDIT(int3, MSG_FAN_SPEED, &preheatFanSpeed1, 0, 255);
#if TEMP_SENSOR_0 != 0
MENU_ITEM_EDIT(int3, MSG_NOZZLE, &plaPreheatHotendTemp, HEATER_0_MINTEMP, HEATER_0_MAXTEMP - 15);
MENU_ITEM_EDIT(int3, MSG_NOZZLE, &preheatHotendTemp1, HEATER_0_MINTEMP, HEATER_0_MAXTEMP - 15);
#endif
#if TEMP_SENSOR_BED != 0
MENU_ITEM_EDIT(int3, MSG_BED, &plaPreheatHPBTemp, BED_MINTEMP, BED_MAXTEMP - 15);
MENU_ITEM_EDIT(int3, MSG_BED, &preheatBedTemp1, BED_MINTEMP, BED_MAXTEMP - 15);
#endif
#if ENABLED(EEPROM_SETTINGS)
MENU_ITEM(function, MSG_STORE_EPROM, Config_StoreSettings);
@ -1751,12 +1746,12 @@ void kill_screen(const char* lcd_msg) {
static void lcd_control_temperature_preheat_abs_settings_menu() {
START_MENU();
MENU_ITEM(back, MSG_TEMPERATURE);
MENU_ITEM_EDIT(int3, MSG_FAN_SPEED, &absPreheatFanSpeed, 0, 255);
MENU_ITEM_EDIT(int3, MSG_FAN_SPEED, &preheatFanSpeed2, 0, 255);
#if TEMP_SENSOR_0 != 0
MENU_ITEM_EDIT(int3, MSG_NOZZLE, &absPreheatHotendTemp, HEATER_0_MINTEMP, HEATER_0_MAXTEMP - 15);
MENU_ITEM_EDIT(int3, MSG_NOZZLE, &preheatHotendTemp2, HEATER_0_MINTEMP, HEATER_0_MAXTEMP - 15);
#endif
#if TEMP_SENSOR_BED != 0
MENU_ITEM_EDIT(int3, MSG_BED, &absPreheatHPBTemp, BED_MINTEMP, BED_MAXTEMP - 15);
MENU_ITEM_EDIT(int3, MSG_BED, &preheatBedTemp2, BED_MINTEMP, BED_MAXTEMP - 15);
#endif
#if ENABLED(EEPROM_SETTINGS)
MENU_ITEM(function, MSG_STORE_EPROM, Config_StoreSettings);

View File

@ -90,12 +90,12 @@
FORCE_INLINE void lcd_buttons_update() {}
#endif
extern int plaPreheatHotendTemp;
extern int plaPreheatHPBTemp;
extern int plaPreheatFanSpeed;
extern int absPreheatHotendTemp;
extern int absPreheatHPBTemp;
extern int absPreheatFanSpeed;
extern int preheatHotendTemp1;
extern int preheatBedTemp1;
extern int preheatFanSpeed1;
extern int preheatHotendTemp2;
extern int preheatBedTemp2;
extern int preheatFanSpeed2;
#if ENABLED(FILAMENT_LCD_DISPLAY)
extern millis_t previous_lcd_status_ms;