2016-07-26 14:32:16 -05:00
/**
* Marlin 3 D Printer Firmware
* Copyright ( C ) 2016 MarlinFirmware [ https : //github.com/MarlinFirmware/Marlin]
*
* Based on Sprinter and grbl .
* Copyright ( C ) 2011 Camiel Gubbels / Erik van der Zalm
*
* This program is free software : you can redistribute it and / or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation , either version 3 of the License , or
* ( at your option ) any later version .
*
* This program is distributed in the hope that it will be useful ,
* but WITHOUT ANY WARRANTY ; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE . See the
* GNU General Public License for more details .
*
* You should have received a copy of the GNU General Public License
* along with this program . If not , see < http : //www.gnu.org/licenses/>.
*
*/
2018-11-01 16:13:33 -05:00
# pragma once
2016-07-26 14:32:16 -05:00
/**
* SanityCheck . h
2016-07-28 19:08:28 -05:00
*
* Test configuration values for errors at compile - time .
*/
/**
2016-12-19 19:12:58 -06:00
* Require gcc 4.7 or newer ( first included with Arduino 1.6 .8 ) for C + + 11 features .
2016-07-28 19:08:28 -05:00
*/
2016-12-19 19:12:58 -06:00
# if __cplusplus < 201103L
# error "Marlin requires C++11 support (gcc >= 4.7, Arduino IDE >= 1.6.8). Please upgrade your toolchain."
2016-07-28 19:08:28 -05:00
# endif
/**
2017-04-11 12:58:55 -05:00
* We try our best to include sanity checks for all changed configuration
* directives because users have a tendency to use outdated config files with
* the bleeding - edge source code , but sometimes this is not enough . This check
* forces a minimum config file revision . Otherwise Marlin will not build .
2016-07-28 19:08:28 -05:00
*/
2018-05-06 09:33:09 -05:00
# define HEXIFY(H) _CAT(0x,H)
# if !defined(CONFIGURATION_H_VERSION) || HEXIFY(CONFIGURATION_H_VERSION) < HEXIFY(REQUIRED_CONFIGURATION_H_VERSION)
2016-07-28 19:08:28 -05:00
# error "You are using an old Configuration.h file, update it before building Marlin."
# endif
2018-05-06 09:33:09 -05:00
# if !defined(CONFIGURATION_ADV_H_VERSION) || HEXIFY(CONFIGURATION_ADV_H_VERSION) < HEXIFY(REQUIRED_CONFIGURATION_ADV_H_VERSION)
2016-07-28 19:08:28 -05:00
# error "You are using an old Configuration_adv.h file, update it before building Marlin."
# endif
2016-09-22 17:10:20 -05:00
/**
2016-08-04 23:03:55 -05:00
* Warnings for old configurations
*/
2018-06-10 04:03:27 -05:00
# ifndef MOTHERBOARD
# error "MOTHERBOARD is required. Please update your configuration."
# elif !defined(X_BED_SIZE) || !defined(Y_BED_SIZE)
2017-08-05 03:28:30 -05:00
# error "X_BED_SIZE and Y_BED_SIZE are now required! Please update your configuration."
2017-07-21 22:54:39 -05:00
# elif WATCH_TEMP_PERIOD > 500
2016-08-04 23:03:55 -05:00
# error "WATCH_TEMP_PERIOD now uses seconds instead of milliseconds."
# elif DISABLED(THERMAL_PROTECTION_HOTENDS) && (defined(WATCH_TEMP_PERIOD) || defined(THERMAL_PROTECTION_PERIOD))
# error "Thermal Runaway Protection for hotends is now enabled with THERMAL_PROTECTION_HOTENDS."
# elif DISABLED(THERMAL_PROTECTION_BED) && defined(THERMAL_PROTECTION_BED_PERIOD)
# error "Thermal Runaway Protection for the bed is now enabled with THERMAL_PROTECTION_BED."
2016-11-05 23:47:38 -05:00
# elif (CORE_IS_XZ || CORE_IS_YZ) && ENABLED(Z_LATE_ENABLE)
# error "Z_LATE_ENABLE can't be used with COREXZ, COREZX, COREYZ, or COREZY."
2016-08-04 23:03:55 -05:00
# elif defined(X_HOME_RETRACT_MM)
# error "[XYZ]_HOME_RETRACT_MM settings have been renamed [XYZ]_HOME_BUMP_MM."
# elif defined(SDCARDDETECTINVERTED)
# error "SDCARDDETECTINVERTED is now SD_DETECT_INVERTED. Please update your configuration."
# elif defined(BTENABLED)
# error "BTENABLED is now BLUETOOTH. Please update your configuration."
# elif defined(CUSTOM_MENDEL_NAME)
# error "CUSTOM_MENDEL_NAME is now CUSTOM_MACHINE_NAME. Please update your configuration."
# elif defined(HAS_AUTOMATIC_VERSIONING)
# error "HAS_AUTOMATIC_VERSIONING is now USE_AUTOMATIC_VERSIONING. Please update your configuration."
# elif defined(SDSLOW)
# error "SDSLOW deprecated. Set SPI_SPEED to SPI_HALF_SPEED instead."
# elif defined(SDEXTRASLOW)
# error "SDEXTRASLOW deprecated. Set SPI_SPEED to SPI_QUARTER_SPEED instead."
# elif defined(FILAMENT_SENSOR)
2018-02-18 19:26:23 -06:00
# error "FILAMENT_SENSOR is now FILAMENT_WIDTH_SENSOR. Please update your configuration."
# elif defined(ENDSTOPPULLUP_FIL_RUNOUT)
# error "ENDSTOPPULLUP_FIL_RUNOUT is now FIL_RUNOUT_PULLUP. Please update your configuration."
2016-08-04 23:03:55 -05:00
# elif defined(DISABLE_MAX_ENDSTOPS) || defined(DISABLE_MIN_ENDSTOPS)
# error "DISABLE_MAX_ENDSTOPS and DISABLE_MIN_ENDSTOPS deprecated. Use individual USE_*_PLUG options instead."
# elif defined(LANGUAGE_INCLUDE)
# error "LANGUAGE_INCLUDE has been replaced by LCD_LANGUAGE. Please update your configuration."
# elif defined(EXTRUDER_OFFSET_X) || defined(EXTRUDER_OFFSET_Y)
# error "EXTRUDER_OFFSET_[XY] is deprecated. Use HOTEND_OFFSET_[XY] instead."
# elif defined(PID_PARAMS_PER_EXTRUDER)
# error "PID_PARAMS_PER_EXTRUDER is deprecated. Use PID_PARAMS_PER_HOTEND instead."
# elif defined(EXTRUDER_WATTS) || defined(BED_WATTS)
# error "EXTRUDER_WATTS and BED_WATTS are deprecated. Remove them from your configuration."
# elif defined(SERVO_ENDSTOP_ANGLES)
# error "SERVO_ENDSTOP_ANGLES is deprecated. Use Z_SERVO_ANGLES instead."
# elif defined(X_ENDSTOP_SERVO_NR) || defined(Y_ENDSTOP_SERVO_NR)
# error "X_ENDSTOP_SERVO_NR and Y_ENDSTOP_SERVO_NR are deprecated and should be removed."
2018-04-01 23:54:12 -05:00
# elif defined(Z_ENDSTOP_SERVO_NR)
# error "Z_ENDSTOP_SERVO_NR is now Z_PROBE_SERVO_NR. Please update your configuration."
2016-10-02 04:37:13 -05:00
# elif defined(DEFAULT_XYJERK)
# error "DEFAULT_XYJERK is deprecated. Use DEFAULT_XJERK and DEFAULT_YJERK instead."
2016-08-04 23:03:55 -05:00
# elif defined(XY_TRAVEL_SPEED)
# error "XY_TRAVEL_SPEED is deprecated. Use XY_PROBE_SPEED instead."
# elif defined(PROBE_SERVO_DEACTIVATION_DELAY)
# error "PROBE_SERVO_DEACTIVATION_DELAY is deprecated. Use DEACTIVATE_SERVOS_AFTER_MOVE instead."
# elif defined(SERVO_DEACTIVATION_DELAY)
# error "SERVO_DEACTIVATION_DELAY is deprecated. Use SERVO_DELAY instead."
# elif ENABLED(FILAMENTCHANGEENABLE)
2017-05-26 13:01:02 -05:00
# error "FILAMENTCHANGEENABLE is now ADVANCED_PAUSE_FEATURE. Please update your configuration."
# elif ENABLED(FILAMENT_CHANGE_FEATURE)
# error "FILAMENT_CHANGE_FEATURE is now ADVANCED_PAUSE_FEATURE. Please update your configuration."
2017-12-25 01:38:06 -06:00
# elif defined(FILAMENT_CHANGE_X_POS) || defined(FILAMENT_CHANGE_Y_POS)
# error "FILAMENT_CHANGE_[XY]_POS is now set with NOZZLE_PARK_POINT. Please update your configuration."
# elif defined(FILAMENT_CHANGE_Z_ADD)
# error "FILAMENT_CHANGE_Z_ADD is now set with NOZZLE_PARK_POINT. Please update your configuration."
# elif defined(FILAMENT_CHANGE_XY_FEEDRATE)
# error "FILAMENT_CHANGE_XY_FEEDRATE is now NOZZLE_PARK_XY_FEEDRATE. Please update your configuration."
# elif defined(FILAMENT_CHANGE_Z_FEEDRATE)
# error "FILAMENT_CHANGE_Z_FEEDRATE is now NOZZLE_PARK_Z_FEEDRATE. Please update your configuration."
# elif defined(PAUSE_PARK_X_POS) || defined(PAUSE_PARK_Y_POS)
# error "PAUSE_PARK_[XY]_POS is now set with NOZZLE_PARK_POINT. Please update your configuration."
# elif defined(PAUSE_PARK_Z_ADD)
# error "PAUSE_PARK_Z_ADD is now set with NOZZLE_PARK_POINT. Please update your configuration."
# elif defined(PAUSE_PARK_XY_FEEDRATE)
# error "PAUSE_PARK_XY_FEEDRATE is now NOZZLE_PARK_XY_FEEDRATE. Please update your configuration."
# elif defined(PAUSE_PARK_Z_FEEDRATE)
# error "PAUSE_PARK_Z_FEEDRATE is now NOZZLE_PARK_Z_FEEDRATE. Please update your configuration."
# elif defined(FILAMENT_CHANGE_RETRACT_FEEDRATE)
2017-05-26 13:01:02 -05:00
# error "FILAMENT_CHANGE_RETRACT_FEEDRATE is now PAUSE_PARK_RETRACT_FEEDRATE. Please update your configuration."
2017-12-25 01:38:06 -06:00
# elif defined(FILAMENT_CHANGE_RETRACT_LENGTH)
2017-05-26 13:01:02 -05:00
# error "FILAMENT_CHANGE_RETRACT_LENGTH is now PAUSE_PARK_RETRACT_LENGTH. Please update your configuration."
2017-12-25 01:38:06 -06:00
# elif defined(FILAMENT_CHANGE_EXTRUDE_FEEDRATE)
2018-04-20 18:16:17 -05:00
# error "FILAMENT_CHANGE_EXTRUDE_FEEDRATE is now ADVANCED_PAUSE_PURGE_FEEDRATE. Please update your configuration."
2018-03-20 13:19:10 -05:00
# elif defined(ADVANCED_PAUSE_EXTRUDE_FEEDRATE)
# error "ADVANCED_PAUSE_EXTRUDE_FEEDRATE is now ADVANCED_PAUSE_PURGE_FEEDRATE. Please update your configuration."
2017-12-25 01:38:06 -06:00
# elif defined(FILAMENT_CHANGE_EXTRUDE_LENGTH)
2018-03-20 13:19:10 -05:00
# error "FILAMENT_CHANGE_EXTRUDE_LENGTH is now ADVANCED_PAUSE_PURGE_LENGTH. Please update your configuration."
# elif defined(ADVANCED_PAUSE_EXTRUDE_LENGTH)
# error "ADVANCED_PAUSE_EXTRUDE_LENGTH is now ADVANCED_PAUSE_PURGE_LENGTH. Please update your configuration."
2017-12-25 01:38:06 -06:00
# elif defined(FILAMENT_CHANGE_NOZZLE_TIMEOUT)
2017-05-26 13:01:02 -05:00
# error "FILAMENT_CHANGE_NOZZLE_TIMEOUT is now PAUSE_PARK_NOZZLE_TIMEOUT. Please update your configuration."
2018-01-04 05:06:34 -06:00
# elif defined(FILAMENT_CHANGE_NUMBER_OF_ALERT_BEEPS)
# error "FILAMENT_CHANGE_NUMBER_OF_ALERT_BEEPS is now FILAMENT_CHANGE_ALERT_BEEPS. Please update your configuration."
2018-11-14 01:15:24 -06:00
# elif defined(FILAMENT_CHANGE_NO_STEPPER_TIMEOUT)
2017-05-26 13:01:02 -05:00
# error "FILAMENT_CHANGE_NO_STEPPER_TIMEOUT is now PAUSE_PARK_NO_STEPPER_TIMEOUT. Please update your configuration."
2016-08-04 23:03:55 -05:00
# elif defined(PLA_PREHEAT_HOTEND_TEMP)
# error "PLA_PREHEAT_HOTEND_TEMP is now PREHEAT_1_TEMP_HOTEND. Please update your configuration."
# elif defined(PLA_PREHEAT_HPB_TEMP)
# error "PLA_PREHEAT_HPB_TEMP is now PREHEAT_1_TEMP_BED. Please update your configuration."
# elif defined(PLA_PREHEAT_FAN_SPEED)
# error "PLA_PREHEAT_FAN_SPEED is now PREHEAT_1_FAN_SPEED. Please update your configuration."
# elif defined(ABS_PREHEAT_HOTEND_TEMP)
# error "ABS_PREHEAT_HOTEND_TEMP is now PREHEAT_2_TEMP_HOTEND. Please update your configuration."
# elif defined(ABS_PREHEAT_HPB_TEMP)
# error "ABS_PREHEAT_HPB_TEMP is now PREHEAT_2_TEMP_BED. Please update your configuration."
# elif defined(ABS_PREHEAT_FAN_SPEED)
# error "ABS_PREHEAT_FAN_SPEED is now PREHEAT_2_FAN_SPEED. Please update your configuration."
# elif defined(ENDSTOPS_ONLY_FOR_HOMING)
# error "ENDSTOPS_ONLY_FOR_HOMING is deprecated. Use (disable) ENDSTOPS_ALWAYS_ON_DEFAULT instead."
# elif defined(HOMING_FEEDRATE)
# error "HOMING_FEEDRATE is deprecated. Set individual rates with HOMING_FEEDRATE_(XY|Z|E) instead."
# elif defined(MANUAL_HOME_POSITIONS)
# error "MANUAL_HOME_POSITIONS is deprecated. Set MANUAL_[XYZ]_HOME_POS as-needed instead."
# elif defined(PID_ADD_EXTRUSION_RATE)
# error "PID_ADD_EXTRUSION_RATE is now PID_EXTRUSION_SCALING and is DISABLED by default. Are you sure you want to use this option? Please update your configuration."
# elif defined(Z_RAISE_BEFORE_HOMING)
# error "Z_RAISE_BEFORE_HOMING is now Z_HOMING_HEIGHT. Please update your configuration."
# elif defined(MIN_Z_HEIGHT_FOR_HOMING)
# error "MIN_Z_HEIGHT_FOR_HOMING is now Z_HOMING_HEIGHT. Please update your configuration."
# elif defined(Z_RAISE_BEFORE_PROBING) || defined(Z_RAISE_AFTER_PROBING)
2018-03-11 13:07:55 -05:00
# error "Z_RAISE_(BEFORE|AFTER)_PROBING are deprecated. Use Z_CLEARANCE_DEPLOY_PROBE and Z_AFTER_PROBING instead."
2016-08-04 23:03:55 -05:00
# elif defined(Z_RAISE_PROBE_DEPLOY_STOW) || defined(Z_RAISE_BETWEEN_PROBINGS)
2016-09-20 03:49:42 -05:00
# error "Z_RAISE_PROBE_DEPLOY_STOW and Z_RAISE_BETWEEN_PROBINGS are now Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES. Please update your configuration."
2016-09-13 20:25:12 -05:00
# elif defined(Z_PROBE_DEPLOY_HEIGHT) || defined(Z_PROBE_TRAVEL_HEIGHT)
2016-09-20 03:49:42 -05:00
# error "Z_PROBE_DEPLOY_HEIGHT and Z_PROBE_TRAVEL_HEIGHT are now Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES. Please update your configuration."
2017-03-13 00:24:22 -05:00
# elif defined(MANUAL_BED_LEVELING)
# error "MANUAL_BED_LEVELING is now LCD_BED_LEVELING. Please update your configuration."
2017-03-15 03:20:41 -05:00
# elif defined(MESH_HOME_SEARCH_Z)
2017-03-13 00:24:22 -05:00
# error "MESH_HOME_SEARCH_Z is now LCD_PROBE_Z_RANGE. Please update your configuration."
# elif defined(MANUAL_PROBE_Z_RANGE)
# error "MANUAL_PROBE_Z_RANGE is now LCD_PROBE_Z_RANGE. Please update your configuration."
2016-08-21 08:56:03 -05:00
# elif !defined(MIN_STEPS_PER_SEGMENT)
2016-08-28 19:40:32 -05:00
# error Please replace "const int dropsegments" with "#define MIN_STEPS_PER_SEGMENT" (and increase by 1) in Configuration_adv.h.
2018-04-12 20:22:29 -05:00
# elif MIN_STEPS_PER_SEGMENT <= 0
# error "MIN_STEPS_PER_SEGMENT must be at least 1. Please update your Configuration_adv.h."
2016-08-20 23:34:24 -05:00
# elif defined(PREVENT_DANGEROUS_EXTRUDE)
# error "PREVENT_DANGEROUS_EXTRUDE is now PREVENT_COLD_EXTRUSION. Please update your configuration."
2016-09-11 20:11:39 -05:00
# elif defined(SCARA)
# error "SCARA is now MORGAN_SCARA. Please update your configuration."
2016-09-25 23:17:39 -05:00
# elif defined(ENABLE_AUTO_BED_LEVELING)
# error "ENABLE_AUTO_BED_LEVELING is deprecated. Specify AUTO_BED_LEVELING_LINEAR, AUTO_BED_LEVELING_BILINEAR, or AUTO_BED_LEVELING_3POINT."
# elif defined(AUTO_BED_LEVELING_FEATURE)
# error "AUTO_BED_LEVELING_FEATURE is deprecated. Specify AUTO_BED_LEVELING_LINEAR, AUTO_BED_LEVELING_BILINEAR, or AUTO_BED_LEVELING_3POINT."
# elif defined(ABL_GRID_POINTS)
2017-04-05 22:29:44 -05:00
# error "ABL_GRID_POINTS is now GRID_MAX_POINTS_X and GRID_MAX_POINTS_Y. Please update your configuration."
2016-12-09 23:38:28 -06:00
# elif defined(ABL_GRID_POINTS_X) || defined(ABL_GRID_POINTS_Y)
2017-04-05 22:29:44 -05:00
# error "ABL_GRID_POINTS_[XY] is now GRID_MAX_POINTS_[XY]. Please update your configuration."
# elif defined(ABL_GRID_MAX_POINTS_X) || defined(ABL_GRID_MAX_POINTS_Y)
# error "ABL_GRID_MAX_POINTS_[XY] is now GRID_MAX_POINTS_[XY]. Please update your configuration."
# elif defined(MESH_NUM_X_POINTS) || defined(MESH_NUM_Y_POINTS)
# error "MESH_NUM_[XY]_POINTS is now GRID_MAX_POINTS_[XY]. Please update your configuration."
# elif defined(UBL_MESH_NUM_X_POINTS) || defined(UBL_MESH_NUM_Y_POINTS)
# error "UBL_MESH_NUM_[XY]_POINTS is now GRID_MAX_POINTS_[XY]. Please update your configuration."
2017-11-23 17:49:05 -06:00
# elif defined(UBL_G26_MESH_VALIDATION)
# error "UBL_G26_MESH_VALIDATION is now G26_MESH_VALIDATION. Please update your configuration."
2017-04-01 20:06:12 -05:00
# elif defined(UBL_MESH_EDIT_ENABLED)
2017-11-23 17:49:05 -06:00
# error "UBL_MESH_EDIT_ENABLED is now G26_MESH_VALIDATION. Please update your configuration."
2017-05-21 11:10:22 -05:00
# elif defined(UBL_MESH_EDITING)
2017-11-23 17:49:05 -06:00
# error "UBL_MESH_EDITING is now G26_MESH_VALIDATION. Please update your configuration."
2017-05-21 22:09:51 -05:00
# elif defined(BLTOUCH_HEATERS_OFF)
# error "BLTOUCH_HEATERS_OFF is now PROBING_HEATERS_OFF. Please update your configuration."
2016-09-24 16:36:12 -05:00
# elif defined(BEEPER)
# error "BEEPER is now BEEPER_PIN. Please update your pins definitions."
# elif defined(SDCARDDETECT)
# error "SDCARDDETECT is now SD_DETECT_PIN. Please update your pins definitions."
# elif defined(STAT_LED_RED) || defined(STAT_LED_BLUE)
# error "STAT_LED_RED / STAT_LED_BLUE are now STAT_LED_RED_PIN / STAT_LED_BLUE_PIN. Please update your pins definitions."
# elif defined(LCD_PIN_BL)
# error "LCD_PIN_BL is now LCD_BACKLIGHT_PIN. Please update your pins definitions."
# elif defined(LCD_PIN_RESET)
# error "LCD_PIN_RESET is now LCD_RESET_PIN. Please update your pins definitions."
2016-10-22 20:20:59 -05:00
# elif defined(EXTRUDER_0_AUTO_FAN_PIN) || defined(EXTRUDER_1_AUTO_FAN_PIN) || defined(EXTRUDER_2_AUTO_FAN_PIN) || defined(EXTRUDER_3_AUTO_FAN_PIN)
# error "EXTRUDER_[0123]_AUTO_FAN_PIN is now E[0123]_AUTO_FAN_PIN. Please update your Configuration_adv.h."
2017-03-16 20:03:57 -05:00
# elif defined(min_software_endstops) || defined(max_software_endstops)
# error "(min|max)_software_endstops are now (MIN|MAX)_SOFTWARE_ENDSTOPS. Please update your configuration."
2017-04-14 16:36:02 -05:00
# elif ENABLED(Z_PROBE_SLED) && defined(SLED_PIN)
# error "Replace SLED_PIN with SOL1_PIN (applies to both Z_PROBE_SLED and SOLENOID_PROBE)."
2017-05-02 20:18:31 -05:00
# elif defined(CONTROLLERFAN_PIN)
# error "CONTROLLERFAN_PIN is now CONTROLLER_FAN_PIN, enabled with USE_CONTROLLER_FAN. Please update your Configuration_adv.h."
2017-07-24 12:13:25 -05:00
# elif defined(MIN_RETRACT)
# error "MIN_RETRACT is now MIN_AUTORETRACT and MAX_AUTORETRACT. Please update your Configuration_adv.h."
2017-10-09 04:25:18 -05:00
# elif defined(ADVANCE)
# error "ADVANCE was removed in Marlin 1.1.6. Please use LIN_ADVANCE."
2018-02-23 00:53:29 -06:00
# elif defined(LIN_ADVANCE_E_D_RATIO)
# error "LIN_ADVANCE (1.5) no longer uses LIN_ADVANCE_E_D_RATIO. Check your configuration."
2017-10-05 06:45:36 -05:00
# elif defined(NEOPIXEL_RGBW_LED)
# error "NEOPIXEL_RGBW_LED is now NEOPIXEL_LED. Please update your configuration."
2018-03-19 01:18:57 -05:00
# elif ENABLED(DELTA) && defined(DELTA_PROBEABLE_RADIUS)
# error "Remove DELTA_PROBEABLE_RADIUS and use MIN_PROBE_EDGE to inset the probe area instead."
2017-10-19 01:39:39 -05:00
# elif defined(UBL_MESH_INSET)
# error "UBL_MESH_INSET is now just MESH_INSET. Please update your configuration."
# elif defined(UBL_MESH_MIN_X) || defined(UBL_MESH_MIN_Y) || defined(UBL_MESH_MAX_X) || defined(UBL_MESH_MAX_Y)
# error "UBL_MESH_(MIN|MAX)_[XY] is now just MESH_(MIN|MAX)_[XY]. Please update your configuration."
2018-03-19 01:22:21 -05:00
# elif defined(ABL_PROBE_PT_1_X) || defined(ABL_PROBE_PT_1_Y) || defined(ABL_PROBE_PT_2_X) || defined(ABL_PROBE_PT_2_Y) || defined(ABL_PROBE_PT_3_X) || defined(ABL_PROBE_PT_3_Y)
# error "ABL_PROBE_PT_[123]_[XY] is now PROBE_PT_[123]_[XY]. Please update your configuration."
# elif defined(UBL_PROBE_PT_1_X) || defined(UBL_PROBE_PT_1_Y) || defined(UBL_PROBE_PT_2_X) || defined(UBL_PROBE_PT_2_Y) || defined(UBL_PROBE_PT_3_X) || defined(UBL_PROBE_PT_3_Y)
# error "UBL_PROBE_PT_[123]_[XY] is now PROBE_PT_[123]_[XY]. Please update your configuration."
2017-11-24 13:35:08 -06:00
# elif defined(ENABLE_MESH_EDIT_GFX_OVERLAY)
# error "ENABLE_MESH_EDIT_GFX_OVERLAY is now MESH_EDIT_GFX_OVERLAY. Please update your configuration."
# elif defined(BABYSTEP_ZPROBE_GFX_REVERSE)
# error "BABYSTEP_ZPROBE_GFX_REVERSE is now set by OVERLAY_GFX_REVERSE. Please update your configurations."
2017-11-29 15:30:42 -06:00
# elif defined(UBL_GRANULAR_SEGMENTATION_FOR_CARTESIAN)
# error "UBL_GRANULAR_SEGMENTATION_FOR_CARTESIAN is now SEGMENT_LEVELED_MOVES. Please update your configuration."
2017-12-01 09:08:30 -06:00
# elif HAS_PID_HEATING && (defined(K1) || !defined(PID_K1))
# error "K1 is now PID_K1. Please update your configuration."
2017-12-07 16:33:51 -06:00
# elif defined(PROBE_DOUBLE_TOUCH)
# error "PROBE_DOUBLE_TOUCH is now MULTIPLE_PROBING. Please update your configuration."
2017-12-15 19:05:57 -06:00
# elif defined(ANET_KEYPAD_LCD)
# error "ANET_KEYPAD_LCD is now ZONESTAR_LCD. Please update your configuration."
2018-02-21 00:46:25 -06:00
# elif defined(LCD_I2C_SAINSMART_YWROBOT)
# error "LCD_I2C_SAINSMART_YWROBOT is now LCD_SAINSMART_I2C_(1602|2004). Please update your configuration."
2017-12-19 21:26:06 -06:00
# elif defined(MEASURED_LOWER_LIMIT) || defined(MEASURED_UPPER_LIMIT)
# error "MEASURED_(UPPER|LOWER)_LIMIT is now FILWIDTH_ERROR_MARGIN. Please update your configuration."
2018-03-13 02:06:40 -05:00
# elif defined(HAVE_TMCDRIVER)
2018-07-14 06:13:06 -05:00
# error "HAVE_TMCDRIVER is now [AXIS]_DRIVER_TYPE TMC26X. Please update your Configuration.h."
2018-12-07 15:34:21 -06:00
# elif defined(STEALTHCHOP)
# error "STEALTHCHOP is now STEALTHCHOP_(XY|Z|E). Please update your Configuration_adv.h."
2018-07-14 06:13:06 -05:00
# elif defined(HAVE_TMC26X)
# error "HAVE_TMC26X is now [AXIS]_DRIVER_TYPE TMC26X. Please update your Configuration.h."
# elif defined(HAVE_TMC2130)
# error "HAVE_TMC2130 is now [AXIS]_DRIVER_TYPE TMC2130. Please update your Configuration.h."
# elif defined(HAVE_L6470DRIVER)
# error "HAVE_L6470DRIVER is now [AXIS]_DRIVER_TYPE L6470. Please update your Configuration.h."
2018-06-19 11:55:49 -05:00
# elif defined(X_IS_TMC) || defined(X2_IS_TMC) || defined(Y_IS_TMC) || defined(Y2_IS_TMC) || defined(Z_IS_TMC) || defined(Z2_IS_TMC) || defined(Z3_IS_TMC) \
2018-09-13 01:35:55 -05:00
| | defined ( E0_IS_TMC ) | | defined ( E1_IS_TMC ) | | defined ( E2_IS_TMC ) | | defined ( E3_IS_TMC ) | | defined ( E4_IS_TMC ) | | defined ( E5_IS_TMC )
2018-07-14 06:13:06 -05:00
# error "[AXIS]_IS_TMC is now [AXIS]_DRIVER_TYPE TMC26X. Please update your Configuration.h."
2018-06-19 11:55:49 -05:00
# elif defined(X_IS_TMC26X) || defined(X2_IS_TMC26X) || defined(Y_IS_TMC26X) || defined(Y2_IS_TMC26X) || defined(Z_IS_TMC26X) || defined(Z2_IS_TMC26X) || defined(Z3_IS_TMC26X) \
2018-09-13 01:35:55 -05:00
| | defined ( E0_IS_TMC26X ) | | defined ( E1_IS_TMC26X ) | | defined ( E2_IS_TMC26X ) | | defined ( E3_IS_TMC26X ) | | defined ( E4_IS_TMC26X ) | | defined ( E5_IS_TMC26X )
2018-07-14 06:13:06 -05:00
# error "[AXIS]_IS_TMC26X is now [AXIS]_DRIVER_TYPE TMC26X. Please update your Configuration.h."
2018-06-19 11:55:49 -05:00
# elif defined(X_IS_TMC2130) || defined(X2_IS_TMC2130) || defined(Y_IS_TMC2130) || defined(Y2_IS_TMC2130) || defined(Z_IS_TMC2130) || defined(Z2_IS_TMC2130) || defined(Z3_IS_TMC2130) \
2018-09-13 01:35:55 -05:00
| | defined ( E0_IS_TMC2130 ) | | defined ( E1_IS_TMC2130 ) | | defined ( E2_IS_TMC2130 ) | | defined ( E3_IS_TMC2130 ) | | defined ( E4_IS_TMC2130 ) | | defined ( E5_IS_TMC2130 )
2018-07-14 06:13:06 -05:00
# error "[AXIS]_IS_TMC2130 is now [AXIS]_DRIVER_TYPE TMC2130. Please update your Configuration.h."
2018-06-19 11:55:49 -05:00
# elif defined(X_IS_TMC2208) || defined(X2_IS_TMC2208) || defined(Y_IS_TMC2208) || defined(Y2_IS_TMC2208) || defined(Z_IS_TMC2208) || defined(Z2_IS_TMC2208) || defined(Z3_IS_TMC2208) \
2018-09-13 01:35:55 -05:00
| | defined ( E0_IS_TMC2208 ) | | defined ( E1_IS_TMC2208 ) | | defined ( E2_IS_TMC2208 ) | | defined ( E3_IS_TMC2208 ) | | defined ( E4_IS_TMC2208 ) | | defined ( E5_IS_TMC2208 )
2018-07-14 06:13:06 -05:00
# error "[AXIS]_IS_TMC2208 is now [AXIS]_DRIVER_TYPE TMC2208. Please update your Configuration.h."
2018-06-19 11:55:49 -05:00
# elif defined(X_IS_L6470) || defined(X2_IS_L6470) || defined(Y_IS_L6470) || defined(Y2_IS_L6470) || defined(Z_IS_L6470) || defined(Z2_IS_L6470) || defined(Z3_IS_L6470) \
2018-09-13 01:35:55 -05:00
| | defined ( E0_IS_L6470 ) | | defined ( E1_IS_L6470 ) | | defined ( E2_IS_L6470 ) | | defined ( E3_IS_L6470 ) | | defined ( E4_IS_L6470 ) | | defined ( E5_IS_L6470 )
2018-07-14 06:13:06 -05:00
# error "[AXIS]_IS_L6470 is now [AXIS]_DRIVER_TYPE L6470. Please update your Configuration.h."
2018-02-04 18:44:10 -06:00
# elif defined(AUTOMATIC_CURRENT_CONTROL)
# error "AUTOMATIC_CURRENT_CONTROL is now MONITOR_DRIVER_STATUS. Please update your configuration."
2018-03-20 13:19:10 -05:00
# elif defined(FILAMENT_CHANGE_LOAD_LENGTH)
# error "FILAMENT_CHANGE_LOAD_LENGTH is now FILAMENT_CHANGE_FAST_LOAD_LENGTH. Please update your configuration."
2018-04-22 02:50:48 -05:00
# elif ENABLED(LEVEL_BED_CORNERS) && !defined(LEVEL_CORNERS_INSET)
# error "LEVEL_BED_CORNERS requires a LEVEL_CORNERS_INSET value. Please update your Configuration.h."
2018-05-26 02:02:39 -05:00
# elif defined(BEZIER_JERK_CONTROL)
# error "BEZIER_JERK_CONTROL is now S_CURVE_ACCELERATION. Please update your configuration."
2018-05-26 02:19:28 -05:00
# elif defined(JUNCTION_DEVIATION_FACTOR)
# error "JUNCTION_DEVIATION_FACTOR is now JUNCTION_DEVIATION_MM. Please update your configuration."
# elif defined(JUNCTION_ACCELERATION_FACTOR)
2018-05-31 20:09:53 -05:00
# error "JUNCTION_ACCELERATION_FACTOR is obsolete. Delete it from Configuration_adv.h."
# elif defined(JUNCTION_ACCELERATION)
# error "JUNCTION_ACCELERATION is obsolete. Delete it from Configuration_adv.h."
2018-06-18 22:04:03 -05:00
# elif defined(MAX7219_DEBUG_STEPPER_HEAD)
# error "MAX7219_DEBUG_STEPPER_HEAD is now MAX7219_DEBUG_PLANNER_HEAD. Please update your configuration."
# elif defined(MAX7219_DEBUG_STEPPER_TAIL)
# error "MAX7219_DEBUG_STEPPER_TAIL is now MAX7219_DEBUG_PLANNER_TAIL. Please update your configuration."
# elif defined(MAX7219_DEBUG_STEPPER_QUEUE)
# error "MAX7219_DEBUG_STEPPER_QUEUE is now MAX7219_DEBUG_PLANNER_QUEUE. Please update your configuration."
2018-09-24 20:59:12 -05:00
# elif defined(ENDSTOP_NOISE_FILTER)
# error "ENDSTOP_NOISE_FILTER is now ENDSTOP_NOISE_THRESHOLD [2-7]. Please update your configuration."
2018-10-16 16:46:24 -05:00
# elif defined(RETRACT_ZLIFT)
# error "RETRACT_ZLIFT is now RETRACT_ZRAISE. Please update your Configuration_adv.h."
2018-10-17 11:11:41 -05:00
# elif defined(TOOLCHANGE_PARK_ZLIFT) || defined(TOOLCHANGE_UNPARK_ZLIFT)
# error "TOOLCHANGE_PARK_ZLIFT and TOOLCHANGE_UNPARK_ZLIFT are now TOOLCHANGE_ZRAISE. Please update your configuration."
# elif defined(SINGLENOZZLE_TOOLCHANGE_ZRAISE)
# error "SINGLENOZZLE_TOOLCHANGE_ZRAISE is now TOOLCHANGE_ZRAISE. Please update your configuration."
2018-11-06 21:52:20 -06:00
# elif defined(SINGLENOZZLE_SWAP_LENGTH)
# error "SINGLENOZZLE_SWAP_LENGTH is now TOOLCHANGE_FIL_SWAP_LENGTH. Please update your configuration."
# elif defined(SINGLENOZZLE_SWAP_RETRACT_SPEED)
# error "SINGLENOZZLE_SWAP_RETRACT_SPEED is now TOOLCHANGE_FIL_SWAP_RETRACT_SPEED. Please update your configuration."
# elif defined(SINGLENOZZLE_SWAP_PRIME_SPEED)
# error "SINGLENOZZLE_SWAP_PRIME_SPEED is now TOOLCHANGE_FIL_SWAP_PRIME_SPEED. Please update your configuration."
# elif defined(SINGLENOZZLE_SWAP_PARK)
# error "SINGLENOZZLE_SWAP_PARK is now TOOLCHANGE_PARK. Please update your configuration."
# elif defined(SINGLENOZZLE_TOOLCHANGE_XY)
# error "SINGLENOZZLE_TOOLCHANGE_XY is now TOOLCHANGE_PARK_XY. Please update your configuration."
# elif defined(SINGLENOZZLE_PARK_XY_FEEDRATE)
# error "SINGLENOZZLE_PARK_XY_FEEDRATE is now TOOLCHANGE_PARK_XY_FEEDRATE. Please update your configuration."
2018-10-17 11:11:41 -05:00
# elif defined(PARKING_EXTRUDER_SECURITY_RAISE)
# error "PARKING_EXTRUDER_SECURITY_RAISE is now TOOLCHANGE_ZRAISE. Please update your configuration."
# elif defined(SWITCHING_TOOLHEAD_SECURITY_RAISE)
# error "SWITCHING_TOOLHEAD_SECURITY_RAISE is now TOOLCHANGE_ZRAISE. Please update your configuration."
2018-10-25 10:35:16 -05:00
# elif defined(G0_FEEDRATE) && G0_FEEDRATE == 0
# error "G0_FEEDRATE is now used to set the G0 feedrate. Please update your configuration."
2018-06-05 21:57:25 -05:00
# elif defined(MBL_Z_STEP)
# error "MBL_Z_STEP is now MESH_EDIT_Z_STEP. Please update your configuration."
2018-11-05 01:08:40 -06:00
# elif defined(CHDK)
# error "CHDK is now CHDK_PIN. Please update your Configuration_adv.h."
2018-11-16 18:20:33 -06:00
# elif defined(MAX6675_SS)
# error "MAX6675_SS is now MAX6675_SS_PIN. Please update your configuration and / or pins."
# elif defined(MAX6675_SS2)
# error "MAX6675_SS2 is now MAX6675_SS2_PIN. Please update your configuration and / or pins."
2016-08-04 23:03:55 -05:00
# endif
2018-04-02 22:01:02 -05:00
# define BOARD_MKS_13 -47
# define BOARD_TRIGORILLA -343
2018-07-25 19:32:27 -05:00
# define BOARD_RURAMPS4D -1550
2018-09-24 20:46:56 -05:00
# define BOARD_FORMBOT_TREX2 -81
2018-04-18 22:58:43 -05:00
# if MB(MKS_13)
# error "BOARD_MKS_13 has been renamed BOARD_MKS_GEN_13. Please update your configuration."
2018-09-24 20:46:56 -05:00
# elif MB(TRIGORILLA)
2018-04-02 22:01:02 -05:00
# error "BOARD_TRIGORILLA has been renamed BOARD_TRIGORILLA_13. Please update your configuration."
2018-09-24 20:46:56 -05:00
# elif MB(RURAMPS4D)
2018-07-25 19:32:27 -05:00
# error "BOARD_RURAMPS4D has been renamed BOARD_RURAMPS4D_11. Please update your configuration."
2018-09-24 20:46:56 -05:00
# elif MB(FORMBOT_TREX2)
# error "FORMBOT_TREX2 has been renamed BOARD_FORMBOT_TREX2PLUS. Please update your configuration."
2018-04-18 22:58:43 -05:00
# endif
2016-07-28 19:08:28 -05:00
/**
* Marlin release , version and default string
*/
# ifndef SHORT_BUILD_VERSION
# error "SHORT_BUILD_VERSION must be specified."
# elif !defined(DETAILED_BUILD_VERSION)
# error "BUILD_VERSION must be specified."
# elif !defined(STRING_DISTRIBUTION_DATE)
# error "STRING_DISTRIBUTION_DATE must be specified."
# elif !defined(PROTOCOL_VERSION)
# error "PROTOCOL_VERSION must be specified."
# elif !defined(MACHINE_NAME)
# error "MACHINE_NAME must be specified."
# elif !defined(SOURCE_CODE_URL)
# error "SOURCE_CODE_URL must be specified."
# elif !defined(DEFAULT_MACHINE_UUID)
# error "DEFAULT_MACHINE_UUID must be specified."
# elif !defined(WEBSITE_URL)
# error "WEBSITE_URL must be specified."
# endif
2017-10-24 17:28:33 -05:00
/**
* Serial
*/
2018-03-13 01:15:22 -05:00
# if !(defined(__AVR__) && defined(USBCON))
2017-10-24 17:28:33 -05:00
# if ENABLED(SERIAL_XON_XOFF) && RX_BUFFER_SIZE < 1024
2017-12-04 05:56:47 -06:00
# error "SERIAL_XON_XOFF requires RX_BUFFER_SIZE >= 1024 for reliable transfers without drops."
2017-12-19 19:11:07 -06:00
# elif RX_BUFFER_SIZE && (RX_BUFFER_SIZE < 2 || !IS_POWER_OF_2(RX_BUFFER_SIZE))
2017-10-24 17:28:33 -05:00
# error "RX_BUFFER_SIZE must be a power of 2 greater than 1."
2017-12-19 19:11:07 -06:00
# elif TX_BUFFER_SIZE && (TX_BUFFER_SIZE < 2 || TX_BUFFER_SIZE > 256 || !IS_POWER_OF_2(TX_BUFFER_SIZE))
2017-12-02 23:07:21 -06:00
# error "TX_BUFFER_SIZE must be 0, a power of 2 greater than 1, and no greater than 256."
2017-10-24 17:28:33 -05:00
# endif
2018-01-09 18:42:55 -06:00
# elif ENABLED(SERIAL_XON_XOFF) || ENABLED(SERIAL_STATS_MAX_RX_QUEUED) || ENABLED(SERIAL_STATS_DROPPED_RX)
# error "SERIAL_XON_XOFF and SERIAL_STATS_* features not supported on USB-native AVR devices."
2017-10-24 17:28:33 -05:00
# endif
2018-02-09 00:44:15 -06:00
# if SERIAL_PORT > 7
# error "Set SERIAL_PORT to the port on your board. Usually this is 0."
# endif
2018-09-28 16:12:19 -05:00
# if defined(SERIAL_PORT_2) && NUM_SERIAL < 2
2018-05-14 21:38:24 -05:00
# error "SERIAL_PORT_2 is not supported for your MOTHERBOARD. Disable it to continue."
# endif
2016-07-28 19:08:28 -05:00
/**
2018-06-19 11:55:49 -05:00
* Dual / Triple Stepper Drivers
2016-07-28 19:08:28 -05:00
*/
# if ENABLED(X_DUAL_STEPPER_DRIVERS) && ENABLED(DUAL_X_CARRIAGE)
# error "DUAL_X_CARRIAGE is not compatible with X_DUAL_STEPPER_DRIVERS."
2018-06-19 11:55:49 -05:00
# elif ENABLED(X_DUAL_STEPPER_DRIVERS) && !(HAS_X2_ENABLE && HAS_X2_STEP && HAS_X2_DIR)
2016-07-28 19:08:28 -05:00
# error "X_DUAL_STEPPER_DRIVERS requires X2 pins (and an extra E plug)."
2018-06-19 11:55:49 -05:00
# elif ENABLED(Y_DUAL_STEPPER_DRIVERS) && !(HAS_Y2_ENABLE && HAS_Y2_STEP && HAS_Y2_DIR)
2016-07-28 19:08:28 -05:00
# error "Y_DUAL_STEPPER_DRIVERS requires Y2 pins (and an extra E plug)."
2018-06-19 11:55:49 -05:00
# elif ENABLED(Z_DUAL_STEPPER_DRIVERS)
# if ENABLED(Z_TRIPLE_STEPPER_DRIVERS)
# error "Please select either Z_TRIPLE_STEPPER_DRIVERS or Z_DUAL_STEPPER_DRIVERS, not both."
# elif !(HAS_Z2_ENABLE && HAS_Z2_STEP && HAS_Z2_DIR)
# error "Z_DUAL_STEPPER_DRIVERS requires Z2 pins (and an extra E plug)."
# endif
# elif ENABLED(Z_TRIPLE_STEPPER_DRIVERS) && !(HAS_Z2_ENABLE && HAS_Z2_STEP && HAS_Z2_DIR && HAS_Z3_ENABLE && HAS_Z3_STEP && HAS_Z3_DIR)
# error "Z_TRIPLE_STEPPER_DRIVERS requires Z3 pins (and two extra E plugs)."
2016-07-28 19:08:28 -05:00
# endif
2017-08-05 03:28:30 -05:00
/**
* Validate that the bed size fits
*/
2019-01-11 15:49:41 -06:00
static_assert ( X_MAX_LENGTH > = X_BED_SIZE , " Movement bounds (X_MIN_POS, X_MAX_POS) are too narrow to contain X_BED_SIZE. " ) ;
static_assert ( Y_MAX_LENGTH > = Y_BED_SIZE , " Movement bounds (Y_MIN_POS, Y_MAX_POS) are too narrow to contain Y_BED_SIZE. " ) ;
2017-08-05 03:28:30 -05:00
2017-10-14 07:18:09 -05:00
/**
* Granular software endstops ( Marlin > = 1.1 .7 )
*/
# if ENABLED(MIN_SOFTWARE_ENDSTOPS) && DISABLED(MIN_SOFTWARE_ENDSTOP_Z)
# if IS_KINEMATIC
# error "MIN_SOFTWARE_ENDSTOPS on DELTA / SCARA also requires MIN_SOFTWARE_ENDSTOP_Z."
# elif DISABLED(MIN_SOFTWARE_ENDSTOP_X) && DISABLED(MIN_SOFTWARE_ENDSTOP_Y)
# error "MIN_SOFTWARE_ENDSTOPS requires at least one of the MIN_SOFTWARE_ENDSTOP_[XYZ] options."
# endif
# endif
# if ENABLED(MAX_SOFTWARE_ENDSTOPS) && DISABLED(MAX_SOFTWARE_ENDSTOP_Z)
# if IS_KINEMATIC
# error "MAX_SOFTWARE_ENDSTOPS on DELTA / SCARA also requires MAX_SOFTWARE_ENDSTOP_Z."
# elif DISABLED(MAX_SOFTWARE_ENDSTOP_X) && DISABLED(MAX_SOFTWARE_ENDSTOP_Y)
# error "MAX_SOFTWARE_ENDSTOPS requires at least one of the MAX_SOFTWARE_ENDSTOP_[XYZ] options."
# endif
# endif
2018-02-18 19:26:23 -06:00
# if !defined(TARGET_LPC1768) && ( \
ENABLED ( ENDSTOPPULLDOWNS ) \
| | ENABLED ( ENDSTOPPULLDOWN_XMAX ) \
| | ENABLED ( ENDSTOPPULLDOWN_YMAX ) \
| | ENABLED ( ENDSTOPPULLDOWN_ZMAX ) \
| | ENABLED ( ENDSTOPPULLDOWN_XMIN ) \
| | ENABLED ( ENDSTOPPULLDOWN_YMIN ) \
| | ENABLED ( ENDSTOPPULLDOWN_ZMIN ) )
# error "PULLDOWN pin mode is not available on the selected board."
# endif
# if ENABLED(ENDSTOPPULLUPS) && ENABLED(ENDSTOPPULLDOWNS)
# error "Enable only one of ENDSTOPPULLUPS or ENDSTOPPULLDOWNS."
# elif ENABLED(FIL_RUNOUT_PULLUP) && ENABLED(FIL_RUNOUT_PULLDOWN)
# error "Enable only one of FIL_RUNOUT_PULLUP or FIL_RUNOUT_PULLDOWN."
# elif ENABLED(ENDSTOPPULLUP_XMAX) && ENABLED(ENDSTOPPULLDOWN_XMAX)
# error "Enable only one of ENDSTOPPULLUP_X_MAX or ENDSTOPPULLDOWN_X_MAX."
# elif ENABLED(ENDSTOPPULLUP_YMAX) && ENABLED(ENDSTOPPULLDOWN_YMAX)
# error "Enable only one of ENDSTOPPULLUP_Y_MAX or ENDSTOPPULLDOWN_Y_MAX."
# elif ENABLED(ENDSTOPPULLUP_ZMAX) && ENABLED(ENDSTOPPULLDOWN_ZMAX)
# error "Enable only one of ENDSTOPPULLUP_Z_MAX or ENDSTOPPULLDOWN_Z_MAX."
# elif ENABLED(ENDSTOPPULLUP_XMIN) && ENABLED(ENDSTOPPULLDOWN_XMIN)
# error "Enable only one of ENDSTOPPULLUP_X_MIN or ENDSTOPPULLDOWN_X_MIN."
# elif ENABLED(ENDSTOPPULLUP_YMIN) && ENABLED(ENDSTOPPULLDOWN_YMIN)
# error "Enable only one of ENDSTOPPULLUP_Y_MIN or ENDSTOPPULLDOWN_Y_MIN."
# elif ENABLED(ENDSTOPPULLUP_ZMIN) && ENABLED(ENDSTOPPULLDOWN_ZMIN)
# error "Enable only one of ENDSTOPPULLUP_Z_MIN or ENDSTOPPULLDOWN_Z_MIN."
# endif
2018-10-18 11:34:52 -05:00
/**
* LCD Info Screen Style
*/
# if LCD_INFO_SCREEN_STYLE > 0
2018-10-25 08:59:28 -05:00
# if HAS_GRAPHICAL_LCD || LCD_WIDTH < 20 || LCD_HEIGHT < 4
2018-10-18 11:34:52 -05:00
# error "Alternative LCD_INFO_SCREEN_STYLE requires 20x4 Character LCD."
# elif LCD_INFO_SCREEN_STYLE > 1
# error "LCD_INFO_SCREEN_STYLE only has options 0 and 1 at this time."
# endif
# endif
2016-07-28 19:08:28 -05:00
/**
* Progress Bar
*/
# if ENABLED(LCD_PROGRESS_BAR)
2018-02-17 08:01:36 -06:00
# if DISABLED(SDSUPPORT) && DISABLED(LCD_SET_PROGRESS_MANUALLY)
# error "LCD_PROGRESS_BAR requires SDSUPPORT or LCD_SET_PROGRESS_MANUALLY."
2018-10-25 08:59:28 -05:00
# elif !HAS_CHARACTER_LCD
2017-12-06 16:56:30 -06:00
# error "LCD_PROGRESS_BAR requires a character LCD."
2018-10-25 08:59:28 -05:00
# elif HAS_GRAPHICAL_LCD
2016-07-28 19:08:28 -05:00
# error "LCD_PROGRESS_BAR does not apply to graphical displays."
2016-09-11 22:42:54 -05:00
# elif ENABLED(FILAMENT_LCD_DISPLAY)
2016-07-28 19:08:28 -05:00
# error "LCD_PROGRESS_BAR and FILAMENT_LCD_DISPLAY are not fully compatible. Comment out this line to use both."
2018-11-11 12:16:24 -06:00
# elif PROGRESS_MSG_EXPIRE < 0
# error "PROGRESS_MSG_EXPIRE must be greater than or equal to 0."
2016-07-28 19:08:28 -05:00
# endif
2018-12-12 17:21:37 -06:00
# elif ENABLED(LCD_SET_PROGRESS_MANUALLY) && !HAS_GRAPHICAL_LCD && DISABLED(EXTENSIBLE_UI)
# error "LCD_SET_PROGRESS_MANUALLY requires LCD_PROGRESS_BAR, Graphical LCD, or EXTENSIBLE_UI."
2016-07-28 19:08:28 -05:00
# endif
2018-03-03 20:07:28 -06:00
/**
* Custom Boot and Status screens
*/
# if DISABLED(DOGLCD) && (ENABLED(SHOW_CUSTOM_BOOTSCREEN) || ENABLED(CUSTOM_STATUS_SCREEN_IMAGE))
# error "Graphical LCD is required for SHOW_CUSTOM_BOOTSCREEN and CUSTOM_STATUS_SCREEN_IMAGE."
# endif
2018-12-12 16:59:20 -06:00
/**
* LCD Lightweight Screen Style
*/
# if ENABLED(LIGHTWEIGHT_UI) && DISABLED(U8GLIB_ST7920)
# error "LIGHTWEIGHT_UI requires a U8GLIB_ST7920-based display."
# endif
2017-02-09 07:02:25 -06:00
/**
* SD File Sorting
*/
# if ENABLED(SDCARD_SORT_ALPHA)
# if SDSORT_LIMIT > 256
# error "SDSORT_LIMIT must be 256 or smaller."
# elif SDSORT_LIMIT < 10
# error "SDSORT_LIMIT should be greater than 9 to be useful."
2017-02-09 07:05:34 -06:00
# elif DISABLED(SDSORT_USES_RAM)
# if ENABLED(SDSORT_DYNAMIC_RAM)
# error "SDSORT_DYNAMIC_RAM requires SDSORT_USES_RAM (which reads the directory into RAM)."
# elif ENABLED(SDSORT_CACHE_NAMES)
# error "SDSORT_CACHE_NAMES requires SDSORT_USES_RAM (which reads the directory into RAM)."
# endif
2017-02-09 07:02:25 -06:00
# endif
2017-10-18 22:18:51 -05:00
# if ENABLED(SDSORT_CACHE_NAMES) && DISABLED(SDSORT_DYNAMIC_RAM)
# if SDSORT_CACHE_VFATS < 2
# error "SDSORT_CACHE_VFATS must be 2 or greater!"
# elif SDSORT_CACHE_VFATS > MAX_VFAT_ENTRIES
# undef SDSORT_CACHE_VFATS
# define SDSORT_CACHE_VFATS MAX_VFAT_ENTRIES
# warning "SDSORT_CACHE_VFATS was reduced to MAX_VFAT_ENTRIES!"
# endif
# endif
2017-02-09 07:02:25 -06:00
# endif
2017-06-09 07:06:23 -05:00
/**
* I2C Position Encoders
*/
# if ENABLED(I2C_POSITION_ENCODERS)
2018-02-08 03:57:11 -06:00
# if DISABLED(BABYSTEPPING) || DISABLED(BABYSTEP_XY)
# error "I2C_POSITION_ENCODERS requires BABYSTEPPING and BABYSTEP_XY."
2017-06-09 10:22:49 -05:00
# elif !WITHIN(I2CPE_ENCODER_CNT, 1, 5)
2017-06-09 07:06:23 -05:00
# error "I2CPE_ENCODER_CNT must be between 1 and 5."
# endif
# endif
2016-07-28 19:08:28 -05:00
/**
* Babystepping
*/
# if ENABLED(BABYSTEPPING)
2017-10-25 15:49:34 -05:00
# if ENABLED(SCARA)
2016-07-28 19:08:28 -05:00
# error "BABYSTEPPING is not implemented for SCARA yet."
2017-04-13 16:29:43 -05:00
# elif ENABLED(DELTA) && ENABLED(BABYSTEP_XY)
2016-07-28 19:08:28 -05:00
# error "BABYSTEPPING only implemented for Z axis on deltabots."
2017-09-06 06:28:32 -05:00
# elif ENABLED(BABYSTEP_ZPROBE_OFFSET) && ENABLED(MESH_BED_LEVELING)
2017-06-17 15:02:25 -05:00
# error "MESH_BED_LEVELING and BABYSTEP_ZPROBE_OFFSET is not a valid combination"
2017-04-13 16:29:43 -05:00
# elif ENABLED(BABYSTEP_ZPROBE_OFFSET) && !HAS_BED_PROBE
# error "BABYSTEP_ZPROBE_OFFSET requires a probe."
2018-08-24 16:35:55 -05:00
# elif ENABLED(BABYSTEP_ZPROBE_GFX_OVERLAY) && DISABLED(DOGLCD)
2018-04-21 19:41:26 -05:00
# error "BABYSTEP_ZPROBE_GFX_OVERLAY requires a Graphical LCD."
2018-08-24 16:35:55 -05:00
# elif ENABLED(BABYSTEP_ZPROBE_GFX_OVERLAY) && DISABLED(BABYSTEP_ZPROBE_OFFSET)
2017-09-27 00:58:46 -05:00
# error "BABYSTEP_ZPROBE_GFX_OVERLAY requires a BABYSTEP_ZPROBE_OFFSET."
2018-09-24 20:46:56 -05:00
# elif ENABLED(BABYSTEP_HOTEND_Z_OFFSET) && !HAS_HOTEND_OFFSET
# error "BABYSTEP_HOTEND_Z_OFFSET requires 2 or more HOTENDS."
2016-07-28 19:08:28 -05:00
# endif
# endif
/**
2018-02-18 02:42:09 -06:00
* Filament Runout needs one or more pins and either SD Support or Auto print start detection
2016-07-28 19:08:28 -05:00
*/
# if ENABLED(FILAMENT_RUNOUT_SENSOR)
2018-02-18 02:42:09 -06:00
# if !PIN_EXISTS(FIL_RUNOUT)
2016-07-28 19:08:28 -05:00
# error "FILAMENT_RUNOUT_SENSOR requires FIL_RUNOUT_PIN."
2018-02-18 02:42:09 -06:00
# elif NUM_RUNOUT_SENSORS > E_STEPPERS
# error "NUM_RUNOUT_SENSORS cannot exceed the number of E steppers."
# elif NUM_RUNOUT_SENSORS > 1 && !PIN_EXISTS(FIL_RUNOUT2)
# error "FILAMENT_RUNOUT_SENSOR with NUM_RUNOUT_SENSORS > 1 requires FIL_RUNOUT2_PIN."
# elif NUM_RUNOUT_SENSORS > 2 && !PIN_EXISTS(FIL_RUNOUT3)
# error "FILAMENT_RUNOUT_SENSOR with NUM_RUNOUT_SENSORS > 2 requires FIL_RUNOUT3_PIN."
# elif NUM_RUNOUT_SENSORS > 3 && !PIN_EXISTS(FIL_RUNOUT4)
# error "FILAMENT_RUNOUT_SENSOR with NUM_RUNOUT_SENSORS > 3 requires FIL_RUNOUT4_PIN."
# elif NUM_RUNOUT_SENSORS > 4 && !PIN_EXISTS(FIL_RUNOUT5)
# error "FILAMENT_RUNOUT_SENSOR with NUM_RUNOUT_SENSORS > 4 requires FIL_RUNOUT5_PIN."
2018-09-13 01:35:55 -05:00
# elif NUM_RUNOUT_SENSORS > 5 && !PIN_EXISTS(FIL_RUNOUT6)
# error "FILAMENT_RUNOUT_SENSOR with NUM_RUNOUT_SENSORS > 5 requires FIL_RUNOUT6_PIN."
2016-07-28 19:08:28 -05:00
# elif DISABLED(SDSUPPORT) && DISABLED(PRINTJOB_TIMER_AUTOSTART)
# error "FILAMENT_RUNOUT_SENSOR requires SDSUPPORT or PRINTJOB_TIMER_AUTOSTART."
2017-05-26 13:01:02 -05:00
# elif DISABLED(ADVANCED_PAUSE_FEATURE)
static_assert ( NULL = = strstr ( FILAMENT_RUNOUT_SCRIPT , " M600 " ) , " ADVANCED_PAUSE_FEATURE is required to use M600 with FILAMENT_RUNOUT_SENSOR. " ) ;
2016-07-28 19:08:28 -05:00
# endif
# endif
/**
2017-05-26 13:01:02 -05:00
* Advanced Pause
2016-07-28 19:08:28 -05:00
*/
2017-05-26 13:01:02 -05:00
# if ENABLED(ADVANCED_PAUSE_FEATURE)
2018-01-04 05:06:34 -06:00
# if !HAS_RESUME_CONTINUE
# error "ADVANCED_PAUSE_FEATURE currently requires an LCD controller or EMERGENCY_PARSER."
2016-12-23 21:48:18 -06:00
# elif ENABLED(EXTRUDER_RUNOUT_PREVENT)
2017-05-26 13:01:02 -05:00
# error "EXTRUDER_RUNOUT_PREVENT is incompatible with ADVANCED_PAUSE_FEATURE."
2017-05-31 21:44:05 -05:00
# elif ENABLED(PARK_HEAD_ON_PAUSE) && DISABLED(SDSUPPORT) && DISABLED(NEWPANEL) && DISABLED(EMERGENCY_PARSER)
2017-03-17 21:24:33 -05:00
# error "PARK_HEAD_ON_PAUSE requires SDSUPPORT, EMERGENCY_PARSER, or an LCD controller."
2017-06-14 21:06:34 -05:00
# elif ENABLED(HOME_BEFORE_FILAMENT_CHANGE) && DISABLED(PAUSE_PARK_NO_STEPPER_TIMEOUT)
2018-01-04 05:06:34 -06:00
# error "HOME_BEFORE_FILAMENT_CHANGE requires PAUSE_PARK_NO_STEPPER_TIMEOUT."
2017-12-25 01:38:06 -06:00
# elif DISABLED(NOZZLE_PARK_FEATURE)
2018-01-04 05:06:34 -06:00
# error "ADVANCED_PAUSE_FEATURE requires NOZZLE_PARK_FEATURE."
# elif ENABLED(PREVENT_LENGTHY_EXTRUDE) && FILAMENT_CHANGE_UNLOAD_LENGTH > EXTRUDE_MAXLENGTH
# error "FILAMENT_CHANGE_UNLOAD_LENGTH must be less than or equal to EXTRUDE_MAXLENGTH."
2018-03-20 13:19:10 -05:00
# elif ENABLED(PREVENT_LENGTHY_EXTRUDE) && FILAMENT_CHANGE_SLOW_LOAD_LENGTH > EXTRUDE_MAXLENGTH
# error "FILAMENT_CHANGE_SLOW_LOAD_LENGTH must be less than or equal to EXTRUDE_MAXLENGTH."
# elif ENABLED(PREVENT_LENGTHY_EXTRUDE) && FILAMENT_CHANGE_FAST_LOAD_LENGTH > EXTRUDE_MAXLENGTH
# error "FILAMENT_CHANGE_FAST_LOAD_LENGTH must be less than or equal to EXTRUDE_MAXLENGTH."
2016-12-23 21:48:18 -06:00
# endif
2016-07-28 19:08:28 -05:00
# endif
2018-09-05 06:18:08 -05:00
# if ENABLED(NOZZLE_PARK_FEATURE)
constexpr float npp [ ] = NOZZLE_PARK_POINT ;
static_assert ( COUNT ( npp ) = = XYZ , " NOZZLE_PARK_POINT requires X, Y, and Z values. " ) ;
# endif
2016-07-28 19:08:28 -05:00
/**
* Individual axis homing is useless for DELTAS
*/
# if ENABLED(INDIVIDUAL_AXIS_HOMING_MENU) && ENABLED(DELTA)
# error "INDIVIDUAL_AXIS_HOMING_MENU is incompatible with DELTA kinematics."
# endif
/**
* Options only for EXTRUDERS > 1
*/
# if EXTRUDERS > 1
2018-11-04 18:36:45 -06:00
# if EXTRUDERS > 6
# error "Marlin supports a maximum of 6 EXTRUDERS."
2016-07-28 19:08:28 -05:00
# endif
# if ENABLED(TEMP_SENSOR_1_AS_REDUNDANT)
# error "EXTRUDERS must be 1 with TEMP_SENSOR_1_AS_REDUNDANT."
# endif
# if ENABLED(HEATERS_PARALLEL)
# error "EXTRUDERS must be 1 with HEATERS_PARALLEL."
# endif
2018-11-06 21:52:20 -06:00
# if ENABLED(TOOLCHANGE_FILAMENT_SWAP)
# ifndef TOOLCHANGE_FIL_SWAP_LENGTH
# error "TOOLCHANGE_FILAMENT_SWAP requires TOOLCHANGE_FIL_SWAP_LENGTH. Please update your Configuration."
# elif !defined(TOOLCHANGE_FIL_SWAP_RETRACT_SPEED)
# error "TOOLCHANGE_FILAMENT_SWAP requires TOOLCHANGE_FIL_SWAP_RETRACT_SPEED. Please update your Configuration."
# elif !defined(TOOLCHANGE_FIL_SWAP_PRIME_SPEED)
# error "TOOLCHANGE_FILAMENT_SWAP requires TOOLCHANGE_FIL_SWAP_PRIME_SPEED. Please update your Configuration."
2018-10-08 15:39:55 -05:00
# endif
2018-11-06 21:52:20 -06:00
# endif
# if ENABLED(TOOLCHANGE_PARK)
# ifndef TOOLCHANGE_PARK_XY
# error "TOOLCHANGE_PARK requires TOOLCHANGE_PARK_XY. Please update your Configuration."
# elif !defined(TOOLCHANGE_PARK_XY_FEEDRATE)
# error "TOOLCHANGE_PARK requires TOOLCHANGE_PARK_XY_FEEDRATE. Please update your Configuration."
2018-10-08 15:39:55 -05:00
# endif
2018-10-07 17:06:14 -05:00
# endif
2018-11-07 02:39:59 -06:00
2018-11-06 21:52:20 -06:00
# ifndef TOOLCHANGE_ZRAISE
# error "TOOLCHANGE_ZRAISE required for EXTRUDERS > 1. Please update your Configuration."
# endif
2018-10-07 17:06:14 -05:00
2017-06-02 13:57:31 -05:00
# elif ENABLED(MK2_MULTIPLEXER)
# error "MK2_MULTIPLEXER requires 2 or more EXTRUDERS."
2016-07-28 19:08:28 -05:00
# elif ENABLED(SINGLENOZZLE)
# error "SINGLENOZZLE requires 2 or more EXTRUDERS."
# endif
2017-06-02 13:57:31 -05:00
/**
* Sanity checking for the Průša MK2 Multiplexer
*/
# ifdef SNMM
# error "SNMM is now MK2_MULTIPLEXER. Please update your configuration."
# endif
2016-07-28 19:08:28 -05:00
/**
2017-06-19 16:54:37 -05:00
* A Dual Nozzle carriage with switching servo
2016-07-28 19:08:28 -05:00
*/
2017-05-12 14:09:40 -05:00
# if ENABLED(SWITCHING_NOZZLE)
2017-06-19 16:54:37 -05:00
# if ENABLED(DUAL_X_CARRIAGE)
# error "SWITCHING_NOZZLE and DUAL_X_CARRIAGE are incompatible."
# elif ENABLED(SINGLENOZZLE)
2017-05-12 14:09:40 -05:00
# error "SWITCHING_NOZZLE and SINGLENOZZLE are incompatible."
2017-06-19 16:54:37 -05:00
# elif EXTRUDERS != 2
2017-05-12 14:09:40 -05:00
# error "SWITCHING_NOZZLE requires exactly 2 EXTRUDERS."
# elif NUM_SERVOS < 1
# error "SWITCHING_NOZZLE requires NUM_SERVOS >= 1."
2018-09-01 01:10:20 -05:00
# elif SWITCHING_NOZZLE_SERVO_NR == 0 && !PIN_EXISTS(SERVO0)
# error "SERVO0_PIN must be defined for your SWITCHING_NOZZLE."
# elif SWITCHING_NOZZLE_SERVO_NR == 1 && !PIN_EXISTS(SERVO1)
# error "SERVO1_PIN must be defined for your SWITCHING_NOZZLE."
# elif SWITCHING_NOZZLE_SERVO_NR == 2 && !PIN_EXISTS(SERVO2)
# error "SERVO2_PIN must be defined for your SWITCHING_NOZZLE."
# elif SWITCHING_NOZZLE_SERVO_NR == 3 && !PIN_EXISTS(SERVO3)
# error "SERVO3_PIN must be defined for your SWITCHING_NOZZLE."
2017-05-12 14:09:40 -05:00
# endif
2016-07-28 19:08:28 -05:00
# endif
/**
* Single Stepper Dual Extruder with switching servo
*/
2018-09-01 01:10:20 -05:00
# if ENABLED(SWITCHING_EXTRUDER)
# if NUM_SERVOS < 1
# error "SWITCHING_EXTRUDER requires NUM_SERVOS >= 1."
# elif SWITCHING_EXTRUDER_SERVO_NR == 0 && !PIN_EXISTS(SERVO0)
# error "SERVO0_PIN must be defined for your SWITCHING_EXTRUDER."
# elif SWITCHING_EXTRUDER_SERVO_NR == 1 && !PIN_EXISTS(SERVO1)
# error "SERVO1_PIN must be defined for your SWITCHING_EXTRUDER."
# elif SWITCHING_EXTRUDER_SERVO_NR == 2 && !PIN_EXISTS(SERVO2)
# error "SERVO2_PIN must be defined for your SWITCHING_EXTRUDER."
# elif SWITCHING_EXTRUDER_SERVO_NR == 3 && !PIN_EXISTS(SERVO3)
# error "SERVO3_PIN must be defined for your SWITCHING_EXTRUDER."
# endif
# if EXTRUDERS > 3
# if NUM_SERVOS < 2
# error "SWITCHING_EXTRUDER with 4 extruders requires NUM_SERVOS >= 2."
# elif SWITCHING_EXTRUDER_E23_SERVO_NR == 0 && !PIN_EXISTS(SERVO0)
# error "SERVO0_PIN must be defined for your SWITCHING_EXTRUDER."
# elif SWITCHING_EXTRUDER_E23_SERVO_NR == 1 && !PIN_EXISTS(SERVO1)
# error "SERVO1_PIN must be defined for your SWITCHING_EXTRUDER."
# elif SWITCHING_EXTRUDER_E23_SERVO_NR == 2 && !PIN_EXISTS(SERVO2)
# error "SERVO2_PIN must be defined for your SWITCHING_EXTRUDER."
# elif SWITCHING_EXTRUDER_E23_SERVO_NR == 3 && !PIN_EXISTS(SERVO3)
# error "SERVO3_PIN must be defined for your SWITCHING_EXTRUDER."
# elif SWITCHING_EXTRUDER_E23_SERVO_NR == SWITCHING_EXTRUDER_SERVO_NR
# error "SWITCHING_EXTRUDER_E23_SERVO_NR should be a different extruder from SWITCHING_EXTRUDER_SERVO_NR."
# endif
# endif
2016-07-28 19:08:28 -05:00
# endif
/**
* Mixing Extruder requirements
*/
# if ENABLED(MIXING_EXTRUDER)
# if EXTRUDERS > 1
# error "MIXING_EXTRUDER currently only supports one extruder."
2017-05-12 14:09:40 -05:00
# elif MIXING_STEPPERS < 2
2016-07-28 19:08:28 -05:00
# error "You must set MIXING_STEPPERS >= 2 for a mixing extruder."
2017-05-12 14:09:40 -05:00
# elif ENABLED(FILAMENT_SENSOR)
2016-07-28 19:08:28 -05:00
# error "MIXING_EXTRUDER is incompatible with FILAMENT_SENSOR. Comment out this line to use it anyway."
2017-05-12 14:09:40 -05:00
# elif ENABLED(SWITCHING_EXTRUDER)
# error "Please select either MIXING_EXTRUDER or SWITCHING_EXTRUDER, not both."
# elif ENABLED(SINGLENOZZLE)
# error "MIXING_EXTRUDER is incompatible with SINGLENOZZLE."
2016-07-28 19:08:28 -05:00
# endif
# endif
2018-03-01 02:10:43 -06:00
/**
* Linear Advance 1.5 - Check K value range
*/
# if ENABLED(LIN_ADVANCE)
static_assert (
WITHIN ( LIN_ADVANCE_K , 0 , 10 ) ,
" LIN_ADVANCE_K must be a value from 0 to 10 (Changed in LIN_ADVANCE v1.5, Marlin 1.1.9). "
) ;
# endif
2017-08-13 16:35:59 -05:00
/**
* Parking Extruder requirements
*/
# if ENABLED(PARKING_EXTRUDER)
# if ENABLED(DUAL_X_CARRIAGE)
# error "PARKING_EXTRUDER and DUAL_X_CARRIAGE are incompatible."
# elif ENABLED(SINGLENOZZLE)
# error "PARKING_EXTRUDER and SINGLENOZZLE are incompatible."
# elif ENABLED(EXT_SOLENOID)
# error "PARKING_EXTRUDER and EXT_SOLENOID are incompatible. (Pins are used twice.)"
# elif EXTRUDERS != 2
# error "PARKING_EXTRUDER requires exactly 2 EXTRUDERS."
# elif !PIN_EXISTS(SOL0) || !PIN_EXISTS(SOL1)
# error "PARKING_EXTRUDER requires SOL0_PIN and SOL1_PIN."
# elif !defined(PARKING_EXTRUDER_PARKING_X)
# error "PARKING_EXTRUDER requires PARKING_EXTRUDER_PARKING_X."
2018-10-17 11:11:41 -05:00
# elif !defined(TOOLCHANGE_ZRAISE)
# error "PARKING_EXTRUDER requires TOOLCHANGE_ZRAISE."
# elif TOOLCHANGE_ZRAISE < 0
# error "TOOLCHANGE_ZRAISE must be 0 or higher."
2017-08-13 16:35:59 -05:00
# elif !defined(PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE) || !WITHIN(PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE, LOW, HIGH)
# error "PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE must be defined as HIGH or LOW."
# elif !defined(PARKING_EXTRUDER_SOLENOIDS_DELAY) || !WITHIN(PARKING_EXTRUDER_SOLENOIDS_DELAY, 0, 2000)
# error "PARKING_EXTRUDER_SOLENOIDS_DELAY must be between 0 and 2000 (ms)."
# endif
# endif
2018-09-08 01:43:24 -05:00
/**
* Switching Toolhead requirements
*/
# if ENABLED(SWITCHING_TOOLHEAD)
# if ENABLED(DUAL_X_CARRIAGE)
# error "SWITCHING_TOOLHEAD and DUAL_X_CARRIAGE are incompatible."
# elif ENABLED(SINGLENOZZLE)
# error "SWITCHING_TOOLHEAD and SINGLENOZZLE are incompatible."
# elif ENABLED(PARKING_EXTRUDER)
# error "SWITCHING_TOOLHEAD and PARKING_EXTRUDER are incompatible."
# elif !defined(SWITCHING_TOOLHEAD_SERVO_NR)
# error "SWITCHING_TOOLHEAD requires SWITCHING_TOOLHEAD_SERVO_NR."
# elif EXTRUDERS < 2
# error "SWITCHING_TOOLHEAD requires at least 2 EXTRUDERS."
# elif NUM_SERVOS < (SWITCHING_TOOLHEAD_SERVO_NR - 1)
# if SWITCHING_TOOLHEAD_SERVO_NR == 0
# error "A SWITCHING_TOOLHEAD_SERVO_NR of 0 requires NUM_SERVOS >= 1."
# elif SWITCHING_TOOLHEAD_SERVO_NR == 1
# error "A SWITCHING_TOOLHEAD_SERVO_NR of 1 requires NUM_SERVOS >= 2."
# elif SWITCHING_TOOLHEAD_SERVO_NR == 2
# error "A SWITCHING_TOOLHEAD_SERVO_NR of 2 requires NUM_SERVOS >= 3."
# elif SWITCHING_TOOLHEAD_SERVO_NR == 3
# error "A SWITCHING_TOOLHEAD_SERVO_NR of 3 requires NUM_SERVOS >= 4."
# endif
2018-10-17 11:11:41 -05:00
# elif !defined(TOOLCHANGE_ZRAISE)
# error "SWITCHING_TOOLHEAD requires TOOLCHANGE_ZRAISE."
# elif TOOLCHANGE_ZRAISE < 0
# error "TOOLCHANGE_ZRAISE must be 0 or higher."
2018-09-08 01:43:24 -05:00
# endif
# endif
2017-08-15 07:48:10 -05:00
/**
* Part - Cooling Fan Multiplexer requirements
*/
# if PIN_EXISTS(FANMUX1)
# if !HAS_FANMUX
# error "FANMUX0_PIN must be set before FANMUX1_PIN can be set."
# endif
# elif PIN_EXISTS(FANMUX2)
# error "FANMUX0_PIN and FANMUX1_PIN must be set before FANMUX2_PIN can be set."
# endif
2017-08-13 16:35:59 -05:00
2016-07-28 19:08:28 -05:00
/**
* Limited number of servos
*/
2018-09-11 16:20:12 -05:00
# if NUM_SERVOS > NUM_SERVO_PLUGS
2018-08-24 21:53:42 -05:00
# error "The selected board doesn't support enough servos for your configuration. Reduce NUM_SERVOS."
2016-07-28 19:08:28 -05:00
# endif
/**
2017-08-03 16:53:55 -05:00
* Servo deactivation depends on servo endstops , switching nozzle , or switching extruder
2016-07-28 19:08:28 -05:00
*/
2018-09-08 01:43:24 -05:00
# if ENABLED(DEACTIVATE_SERVOS_AFTER_MOVE) && !HAS_Z_SERVO_PROBE && !defined(SWITCHING_NOZZLE_SERVO_NR) && !defined(SWITCHING_EXTRUDER_SERVO_NR) && !defined(SWITCHING_TOOLHEAD_SERVO_NR)
# error "Z_PROBE_SERVO_NR, switching nozzle, switching toolhead or switching extruder is required for DEACTIVATE_SERVOS_AFTER_MOVE."
2016-07-28 19:08:28 -05:00
# endif
/**
* Required LCD language
*/
# if DISABLED(DOGLCD) && ENABLED(ULTRA_LCD) && !defined(DISPLAY_CHARSET_HD44780)
# error "You must set DISPLAY_CHARSET_HD44780 to JAPANESE, WESTERN or CYRILLIC for your LCD controller."
# endif
/**
* Bed Heating Options - PID vs Limit Switching
*/
# if ENABLED(PIDTEMPBED) && ENABLED(BED_LIMIT_SWITCHING)
# error "To use BED_LIMIT_SWITCHING you must disable PIDTEMPBED."
# endif
2016-09-25 23:17:39 -05:00
/**
2017-06-06 07:19:27 -05:00
* Kinematics
*/
/**
* Allow only one kinematic type to be defined
2016-09-25 23:17:39 -05:00
*/
2018-03-16 02:26:03 -05:00
# if 1 < 0 \
+ ENABLED ( DELTA ) \
+ ENABLED ( MORGAN_SCARA ) \
+ ENABLED ( MAKERARM_SCARA ) \
+ ENABLED ( COREXY ) \
+ ENABLED ( COREXZ ) \
+ ENABLED ( COREYZ ) \
+ ENABLED ( COREYX ) \
+ ENABLED ( COREZX ) \
+ ENABLED ( COREZY )
# error "Please enable only one of DELTA, MORGAN_SCARA, MAKERARM_SCARA, COREXY, COREYX, COREXZ, COREZX, COREYZ, or COREZY."
# endif
2017-03-18 10:02:54 -05:00
/**
2017-06-06 07:19:27 -05:00
* Delta requirements
2017-03-18 10:02:54 -05:00
*/
2017-06-06 07:19:27 -05:00
# if ENABLED(DELTA)
2018-02-11 01:41:40 -06:00
# if DISABLED(USE_XMAX_PLUG) && DISABLED(USE_YMAX_PLUG) && DISABLED(USE_ZMAX_PLUG)
2017-06-06 07:19:27 -05:00
# error "You probably want to use Max Endstops for DELTA!"
2017-12-09 02:11:31 -06:00
# elif ENABLED(ENABLE_LEVELING_FADE_HEIGHT) && DISABLED(AUTO_BED_LEVELING_BILINEAR) && !UBL_SEGMENTED
2017-06-06 07:19:27 -05:00
# error "ENABLE_LEVELING_FADE_HEIGHT on DELTA requires AUTO_BED_LEVELING_BILINEAR or AUTO_BED_LEVELING_UBL."
2018-10-30 16:34:45 -05:00
# elif ENABLED(DELTA_AUTO_CALIBRATION) && !(HAS_BED_PROBE || HAS_LCD_MENU)
2017-11-07 19:34:34 -06:00
# error "DELTA_AUTO_CALIBRATION requires a probe or LCD Controller."
2017-06-06 07:19:27 -05:00
# elif ABL_GRID
# if (GRID_MAX_POINTS_X & 1) == 0 || (GRID_MAX_POINTS_Y & 1) == 0
# error "DELTA requires GRID_MAX_POINTS_X and GRID_MAX_POINTS_Y to be odd numbers."
# elif GRID_MAX_POINTS_X < 3
# error "DELTA requires GRID_MAX_POINTS_X and GRID_MAX_POINTS_Y to be 3 or higher."
# endif
2017-03-18 10:02:54 -05:00
# endif
2016-07-28 19:08:28 -05:00
# endif
/**
* Probes
*/
2017-03-16 16:31:34 -05:00
/**
* Allow only one probe option to be defined
*/
2018-03-16 02:26:03 -05:00
# if 1 < 0 \
+ ENABLED ( PROBE_MANUALLY ) \
+ ENABLED ( FIX_MOUNTED_PROBE ) \
2018-04-01 23:54:12 -05:00
+ ( HAS_Z_SERVO_PROBE & & DISABLED ( BLTOUCH ) ) \
2018-03-16 02:26:03 -05:00
+ ENABLED ( BLTOUCH ) \
+ ENABLED ( SOLENOID_PROBE ) \
+ ENABLED ( Z_PROBE_ALLEN_KEY ) \
2018-10-26 16:47:38 -05:00
+ ENABLED ( Z_PROBE_SLED ) \
+ ENABLED ( RACK_AND_PINION_PROBE )
2018-03-16 02:26:03 -05:00
# error "Please enable only one probe option: PROBE_MANUALLY, FIX_MOUNTED_PROBE, BLTOUCH, SOLENOID_PROBE, Z_PROBE_ALLEN_KEY, Z_PROBE_SLED, or Z Servo."
# endif
2017-03-16 16:31:34 -05:00
2017-11-25 20:08:02 -06:00
# if HAS_BED_PROBE
2016-09-18 23:28:11 -05:00
/**
* Z_PROBE_SLED is incompatible with DELTA
*/
2016-07-28 19:08:28 -05:00
# if ENABLED(Z_PROBE_SLED) && ENABLED(DELTA)
# error "You cannot use Z_PROBE_SLED with DELTA."
# endif
2017-04-14 16:36:02 -05:00
/**
* SOLENOID_PROBE requirements
*/
# if ENABLED(SOLENOID_PROBE)
# if ENABLED(EXT_SOLENOID)
# error "SOLENOID_PROBE is incompatible with EXT_SOLENOID."
# elif !HAS_SOLENOID_1
# error "SOLENOID_PROBE requires SOL1_PIN. It can be added to your Configuration.h."
# endif
# endif
2016-07-28 19:08:28 -05:00
/**
* NUM_SERVOS is required for a Z servo probe
*/
2018-04-01 23:54:12 -05:00
# if HAS_Z_SERVO_PROBE
2016-07-28 19:08:28 -05:00
# ifndef NUM_SERVOS
2018-04-01 23:54:12 -05:00
# error "You must set NUM_SERVOS for a Z servo probe (Z_PROBE_SERVO_NR)."
2018-08-31 15:47:35 -05:00
# elif Z_PROBE_SERVO_NR == 0 && !PIN_EXISTS(SERVO0)
# error "SERVO0_PIN must be defined for your servo or BLTOUCH probe."
# elif Z_PROBE_SERVO_NR == 1 && !PIN_EXISTS(SERVO1)
# error "SERVO1_PIN must be defined for your servo or BLTOUCH probe."
# elif Z_PROBE_SERVO_NR == 2 && !PIN_EXISTS(SERVO2)
# error "SERVO2_PIN must be defined for your servo or BLTOUCH probe."
# elif Z_PROBE_SERVO_NR == 3 && !PIN_EXISTS(SERVO3)
# error "SERVO3_PIN must be defined for your servo or BLTOUCH probe."
2018-04-01 23:54:12 -05:00
# elif Z_PROBE_SERVO_NR >= NUM_SERVOS
# error "Z_PROBE_SERVO_NR must be smaller than NUM_SERVOS."
2016-07-28 19:08:28 -05:00
# endif
# endif
2018-10-26 16:47:38 -05:00
# if ENABLED(RACK_AND_PINION_PROBE) && !(defined(Z_PROBE_DEPLOY_X) && defined(Z_PROBE_RETRACT_X))
# error "RACK_AND_PINION_PROBE requires Z_PROBE_DEPLOY_X and Z_PROBE_RETRACT_X."
# endif
2016-07-28 19:08:28 -05:00
/**
2016-09-18 23:28:11 -05:00
* Require pin options and pins to be defined
2016-07-28 19:08:28 -05:00
*/
2018-09-09 14:59:12 -05:00
# if ENABLED(SENSORLESS_PROBING)
# if ENABLED(DELTA) && (!AXIS_DRIVER_TYPE_X(TMC2130) || !AXIS_DRIVER_TYPE_Y(TMC2130) || !AXIS_DRIVER_TYPE_Z(TMC2130))
# error "SENSORLESS_PROBING requires TMC2130 drivers on X, Y, and Z."
# elif !AXIS_DRIVER_TYPE_Z(TMC2130)
# error "SENSORLESS_PROBING requires a TMC2130 driver on Z."
# endif
# elif ENABLED(Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN)
2016-09-18 23:28:11 -05:00
# if ENABLED(Z_MIN_PROBE_ENDSTOP)
# error "Enable only one option: Z_MIN_PROBE_ENDSTOP or Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN."
# elif DISABLED(USE_ZMIN_PLUG)
# error "Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN requires USE_ZMIN_PLUG to be enabled."
# elif !HAS_Z_MIN
# error "Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN requires the Z_MIN_PIN to be defined."
2018-09-29 00:24:12 -05:00
# elif Z_MIN_PROBE_ENDSTOP_INVERTING != Z_MIN_ENDSTOP_INVERTING
2016-12-07 03:37:37 -06:00
# error "Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN requires Z_MIN_ENDSTOP_INVERTING to match Z_MIN_PROBE_ENDSTOP_INVERTING."
2016-08-02 22:55:17 -05:00
# endif
2016-09-18 23:28:11 -05:00
# elif ENABLED(Z_MIN_PROBE_ENDSTOP)
2016-07-28 19:08:28 -05:00
# if !HAS_Z_MIN_PROBE_PIN
2016-09-18 23:28:11 -05:00
# error "Z_MIN_PROBE_ENDSTOP requires the Z_MIN_PROBE_PIN to be defined."
2016-07-28 19:08:28 -05:00
# endif
2017-11-07 19:34:34 -06:00
# else
2016-09-18 23:28:11 -05:00
# error "You must enable either Z_MIN_PROBE_ENDSTOP or Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use a probe."
2016-07-28 19:08:28 -05:00
# endif
/**
* Make sure Z raise values are set
*/
2017-10-01 21:33:52 -05:00
# ifndef Z_CLEARANCE_DEPLOY_PROBE
2016-09-20 03:49:42 -05:00
# error "You must define Z_CLEARANCE_DEPLOY_PROBE in your configuration."
# elif !defined(Z_CLEARANCE_BETWEEN_PROBES)
# error "You must define Z_CLEARANCE_BETWEEN_PROBES in your configuration."
# elif Z_CLEARANCE_DEPLOY_PROBE < 0
# error "Probes need Z_CLEARANCE_DEPLOY_PROBE >= 0."
# elif Z_CLEARANCE_BETWEEN_PROBES < 0
# error "Probes need Z_CLEARANCE_BETWEEN_PROBES >= 0."
2018-03-11 13:07:55 -05:00
# elif Z_AFTER_PROBING < 0
# error "Probes need Z_AFTER_PROBING >= 0."
2016-07-28 19:08:28 -05:00
# endif
2017-12-07 16:33:51 -06:00
# if MULTIPLE_PROBING && MULTIPLE_PROBING < 2
# error "MULTIPLE_PROBING must be >= 2."
# endif
2018-04-09 01:46:23 -05:00
# if Z_PROBE_LOW_POINT > 0
# error "Z_PROBE_LOW_POINT must be less than or equal to 0."
# endif
2016-07-28 19:08:28 -05:00
# else
/**
* Require some kind of probe for bed leveling and probe testing
*/
2017-11-07 19:34:34 -06:00
# if OLDSCHOOL_ABL && !PROBE_SELECTED
2017-09-06 06:28:32 -05:00
# error "Auto Bed Leveling requires one of these: PROBE_MANUALLY, FIX_MOUNTED_PROBE, BLTOUCH, SOLENOID_PROBE, Z_PROBE_ALLEN_KEY, Z_PROBE_SLED, or a Z Servo."
2016-07-28 19:08:28 -05:00
# endif
2017-11-07 19:34:34 -06:00
# if ENABLED(Z_MIN_PROBE_REPEATABILITY_TEST)
# error "Z_MIN_PROBE_REPEATABILITY_TEST requires a probe: FIX_MOUNTED_PROBE, BLTOUCH, SOLENOID_PROBE, Z_PROBE_ALLEN_KEY, Z_PROBE_SLED, or Z Servo."
# endif
2016-07-28 19:08:28 -05:00
2017-07-02 02:26:35 -05:00
# endif
2017-06-06 07:19:27 -05:00
/**
* Allow only one bed leveling option to be defined
*/
2018-03-16 02:26:03 -05:00
# if 1 < 0 \
+ ENABLED ( AUTO_BED_LEVELING_LINEAR ) \
+ ENABLED ( AUTO_BED_LEVELING_3POINT ) \
+ ENABLED ( AUTO_BED_LEVELING_BILINEAR ) \
+ ENABLED ( AUTO_BED_LEVELING_UBL ) \
+ ENABLED ( MESH_BED_LEVELING )
# error "Select only one of: MESH_BED_LEVELING, AUTO_BED_LEVELING_LINEAR, AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_BILINEAR or AUTO_BED_LEVELING_UBL."
# endif
2017-06-06 07:19:27 -05:00
/**
* Bed Leveling Requirements
*/
2018-03-19 01:22:21 -05:00
# if ENABLED(AUTO_BED_LEVELING_UBL) || ENABLED(AUTO_BED_LEVELING_3POINT)
static_assert ( WITHIN ( PROBE_PT_1_X , MIN_PROBE_X , MAX_PROBE_X ) , " PROBE_PT_1_X is outside the probe region. " ) ;
static_assert ( WITHIN ( PROBE_PT_2_X , MIN_PROBE_X , MAX_PROBE_X ) , " PROBE_PT_2_X is outside the probe region. " ) ;
static_assert ( WITHIN ( PROBE_PT_3_X , MIN_PROBE_X , MAX_PROBE_X ) , " PROBE_PT_3_X is outside the probe region. " ) ;
static_assert ( WITHIN ( PROBE_PT_1_Y , MIN_PROBE_Y , MAX_PROBE_Y ) , " PROBE_PT_1_Y is outside the probe region. " ) ;
static_assert ( WITHIN ( PROBE_PT_2_Y , MIN_PROBE_Y , MAX_PROBE_Y ) , " PROBE_PT_2_Y is outside the probe region. " ) ;
static_assert ( WITHIN ( PROBE_PT_3_Y , MIN_PROBE_Y , MAX_PROBE_Y ) , " PROBE_PT_3_Y is outside the probe region. " ) ;
# endif
2017-06-06 07:19:27 -05:00
# if ENABLED(AUTO_BED_LEVELING_UBL)
/**
* Unified Bed Leveling
*/
2017-11-07 19:34:34 -06:00
// Hide PROBE_MANUALLY from the rest of the code
# undef PROBE_MANUALLY
2017-06-06 07:19:27 -05:00
# if IS_SCARA
# error "AUTO_BED_LEVELING_UBL does not yet support SCARA printers."
# elif DISABLED(EEPROM_SETTINGS)
# error "AUTO_BED_LEVELING_UBL requires EEPROM_SETTINGS. Please update your configuration."
# elif !WITHIN(GRID_MAX_POINTS_X, 3, 15) || !WITHIN(GRID_MAX_POINTS_Y, 3, 15)
# error "GRID_MAX_POINTS_[XY] must be a whole number between 3 and 15."
2018-04-08 03:19:37 -05:00
# elif !defined(RESTORE_LEVELING_AFTER_G28)
# error "AUTO_BED_LEVELING_UBL used to enable RESTORE_LEVELING_AFTER_G28. To keep this behavior enable RESTORE_LEVELING_AFTER_G28. Otherwise define it as 'false'."
2017-06-06 07:19:27 -05:00
# endif
2017-11-07 19:34:34 -06:00
# elif OLDSCHOOL_ABL
2017-06-06 07:19:27 -05:00
/**
* Auto Bed Leveling
*/
/**
* Delta and SCARA have limited bed leveling options
*/
# if IS_SCARA && DISABLED(AUTO_BED_LEVELING_BILINEAR)
2018-03-19 01:22:21 -05:00
# error "SCARA machines can only use the AUTO_BED_LEVELING_BILINEAR leveling option."
2017-06-06 07:19:27 -05:00
# endif
/**
* Check auto bed leveling probe points
*/
# if ABL_GRID
2018-03-13 01:15:22 -05:00
static_assert ( LEFT_PROBE_BED_POSITION < RIGHT_PROBE_BED_POSITION , " LEFT_PROBE_BED_POSITION must be less than RIGHT_PROBE_BED_POSITION. " ) ;
static_assert ( FRONT_PROBE_BED_POSITION < BACK_PROBE_BED_POSITION , " FRONT_PROBE_BED_POSITION must be less than BACK_PROBE_BED_POSITION. " ) ;
static_assert ( LEFT_PROBE_BED_POSITION > = MIN_PROBE_X , " LEFT_PROBE_BED_POSITION is outside the probe region. " ) ;
static_assert ( RIGHT_PROBE_BED_POSITION < = MAX_PROBE_X , " RIGHT_PROBE_BED_POSITION is outside the probe region. " ) ;
static_assert ( FRONT_PROBE_BED_POSITION > = MIN_PROBE_Y , " FRONT_PROBE_BED_POSITION is outside the probe region. " ) ;
static_assert ( BACK_PROBE_BED_POSITION < = MAX_PROBE_Y , " BACK_PROBE_BED_POSITION is outside the probe region. " ) ;
2017-06-06 07:19:27 -05:00
# endif // AUTO_BED_LEVELING_3POINT
# elif ENABLED(MESH_BED_LEVELING)
2017-11-07 19:34:34 -06:00
// Hide PROBE_MANUALLY from the rest of the code
# undef PROBE_MANUALLY
2017-06-06 07:19:27 -05:00
/**
* Mesh Bed Leveling
*/
# if ENABLED(DELTA)
2017-11-08 22:13:33 -06:00
# error "MESH_BED_LEVELING is not compatible with DELTA printers."
2017-06-06 07:19:27 -05:00
# elif GRID_MAX_POINTS_X > 9 || GRID_MAX_POINTS_Y > 9
# error "GRID_MAX_POINTS_X and GRID_MAX_POINTS_Y must be less than 10 for MBL."
# endif
# endif
2018-12-30 10:44:15 -06:00
# if HAS_MESH
# if DISABLED(JUNCTION_DEVIATION)
static_assert ( DEFAULT_ZJERK > 0.1 , " Low DEFAULT_ZJERK values are incompatible with mesh-based leveling. " ) ;
# endif
2018-03-28 23:08:33 -05:00
# elif ENABLED(G26_MESH_VALIDATION)
2017-11-23 17:49:05 -06:00
# error "G26_MESH_VALIDATION requires MESH_BED_LEVELING, AUTO_BED_LEVELING_BILINEAR, or AUTO_BED_LEVELING_UBL."
# endif
2017-11-24 13:35:08 -06:00
# if ENABLED(MESH_EDIT_GFX_OVERLAY) && (DISABLED(AUTO_BED_LEVELING_UBL) || DISABLED(DOGLCD))
# error "MESH_EDIT_GFX_OVERLAY requires AUTO_BED_LEVELING_UBL and a Graphical LCD."
# endif
2018-06-29 20:48:11 -05:00
# if ENABLED(G29_RETRY_AND_RECOVER) && HAS_LEVELING && !OLDSCHOOL_ABL
# error "G29_RETRY_AND_RECOVER currently only supports ABL"
# endif
2017-03-16 16:31:34 -05:00
/**
2017-03-13 00:24:22 -05:00
* LCD_BED_LEVELING requirements
2017-03-16 16:31:34 -05:00
*/
2017-05-31 21:44:05 -05:00
# if ENABLED(LCD_BED_LEVELING)
2018-11-06 19:25:57 -06:00
# if !HAS_LCD_MENU
# error "LCD_BED_LEVELING requires a programmable LCD controller."
2018-05-01 07:10:43 -05:00
# elif !(ENABLED(MESH_BED_LEVELING) || OLDSCHOOL_ABL)
# error "LCD_BED_LEVELING requires MESH_BED_LEVELING or AUTO_BED_LEVELING."
2017-05-31 21:44:05 -05:00
# endif
2017-03-16 16:31:34 -05:00
# endif
2016-09-22 17:10:20 -05:00
/**
2018-02-16 09:59:44 -06:00
* Homing
2016-09-22 17:10:20 -05:00
*/
# if X_HOME_BUMP_MM < 0 || Y_HOME_BUMP_MM < 0 || Z_HOME_BUMP_MM < 0
# error "[XYZ]_HOME_BUMP_MM must be greater than or equal to 0."
# endif
2018-02-16 09:59:44 -06:00
# if ENABLED(CODEPENDENT_XY_HOMING)
# if ENABLED(QUICK_HOME)
# error "QUICK_HOME is incompatible with CODEPENDENT_XY_HOMING."
# elif IS_KINEMATIC
# error "CODEPENDENT_XY_HOMING requires a Cartesian setup."
# endif
# endif
2016-07-28 19:08:28 -05:00
/**
* Make sure Z_SAFE_HOMING point is reachable
*/
# if ENABLED(Z_SAFE_HOMING)
2018-02-28 05:27:16 -06:00
# if HAS_BED_PROBE
2018-07-14 06:13:06 -05:00
static_assert ( WITHIN ( Z_SAFE_HOMING_X_POINT , MIN_PROBE_X , MAX_PROBE_X ) , " Z_SAFE_HOMING_X_POINT is outside the probe region. " ) ;
static_assert ( WITHIN ( Z_SAFE_HOMING_Y_POINT , MIN_PROBE_Y , MAX_PROBE_Y ) , " Z_SAFE_HOMING_Y_POINT is outside the probe region. " ) ;
2018-03-31 19:01:48 -05:00
# else
2018-07-14 06:13:06 -05:00
static_assert ( WITHIN ( Z_SAFE_HOMING_X_POINT , X_MIN_POS , X_MAX_POS ) , " Z_SAFE_HOMING_X_POINT can't be reached by the nozzle. " ) ;
static_assert ( WITHIN ( Z_SAFE_HOMING_Y_POINT , Y_MIN_POS , Y_MAX_POS ) , " Z_SAFE_HOMING_Y_POINT can't be reached by the nozzle. " ) ;
2016-07-28 19:08:28 -05:00
# endif
# endif // Z_SAFE_HOMING
2017-07-03 19:23:53 -05:00
/**
* Make sure DISABLE_ [ XYZ ] compatible with selected homing options
*/
# if ENABLED(DISABLE_X) || ENABLED(DISABLE_Y) || ENABLED(DISABLE_Z)
# if ENABLED(HOME_AFTER_DEACTIVATE) || ENABLED(Z_SAFE_HOMING)
2017-12-19 19:44:11 -06:00
# error "DISABLE_[XYZ] is not compatible with HOME_AFTER_DEACTIVATE or Z_SAFE_HOMING."
2017-07-03 19:23:53 -05:00
# endif
2018-11-05 02:19:55 -06:00
# endif
2017-07-03 19:23:53 -05:00
2016-07-28 19:08:28 -05:00
/**
* Filament Width Sensor
*/
2017-12-19 19:44:11 -06:00
# if ENABLED(FILAMENT_WIDTH_SENSOR)
# if !HAS_FILAMENT_WIDTH_SENSOR
# error "FILAMENT_WIDTH_SENSOR requires a FILWIDTH_PIN to be defined."
# elif ENABLED(NO_VOLUMETRICS)
# error "FILAMENT_WIDTH_SENSOR requires NO_VOLUMETRICS to be disabled."
# endif
2016-07-28 19:08:28 -05:00
# endif
/**
* ULTIPANEL encoder
*/
# if ENABLED(ULTIPANEL) && DISABLED(NEWPANEL) && DISABLED(SR_LCD_2W_NL) && !defined(SHIFT_CLK)
# error "ULTIPANEL requires some kind of encoder."
# endif
# if ENCODER_PULSES_PER_STEP < 0
# error "ENCODER_PULSES_PER_STEP should not be negative, use REVERSE_MENU_DIRECTION instead."
# endif
/**
* SAV_3DGLCD display options
*/
2018-05-06 19:16:55 -05:00
# if ENABLED(SAV_3DGLCD)
# if DISABLED(U8GLIB_SSD1306) && DISABLED(U8GLIB_SH1106)
# error "Enable a SAV_3DGLCD display type: U8GLIB_SSD1306 or U8GLIB_SH1106."
# elif ENABLED(U8GLIB_SSD1306) && ENABLED(U8GLIB_SH1106)
# error "Only enable one SAV_3DGLCD display type: U8GLIB_SSD1306 or U8GLIB_SH1106."
# endif
2016-07-28 19:08:28 -05:00
# endif
/**
* Allen Key
* Deploying the Allen Key probe uses big moves in z direction . Too dangerous for an unhomed z - axis .
*/
# if ENABLED(Z_PROBE_ALLEN_KEY) && (Z_HOME_DIR < 0) && ENABLED(Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN)
# error "You can't home to a z min endstop with a Z_PROBE_ALLEN_KEY"
# endif
/**
* Dual X Carriage requirements
*/
# if ENABLED(DUAL_X_CARRIAGE)
# if EXTRUDERS == 1
# error "DUAL_X_CARRIAGE requires 2 (or more) extruders."
2016-11-05 23:47:38 -05:00
# elif CORE_IS_XY || CORE_IS_XZ
# error "DUAL_X_CARRIAGE cannot be used with COREXY, COREYX, COREXZ, or COREZX."
2018-06-19 11:55:49 -05:00
# elif !(HAS_X2_ENABLE && HAS_X2_STEP && HAS_X2_DIR)
2016-07-28 19:08:28 -05:00
# error "DUAL_X_CARRIAGE requires X2 stepper pins to be defined."
# elif !HAS_X_MAX
# error "DUAL_X_CARRIAGE requires USE_XMAX_PLUG and an X Max Endstop."
# elif !defined(X2_HOME_POS) || !defined(X2_MIN_POS) || !defined(X2_MAX_POS)
# error "DUAL_X_CARRIAGE requires X2_HOME_POS, X2_MIN_POS, and X2_MAX_POS."
# elif X_HOME_DIR != -1 || X2_HOME_DIR != 1
# error "DUAL_X_CARRIAGE requires X_HOME_DIR -1 and X2_HOME_DIR 1."
# endif
# endif // DUAL_X_CARRIAGE
/**
* Make sure auto fan pins don ' t conflict with the fan pin
*/
# if HAS_AUTO_FAN
# if HAS_FAN0
2016-10-22 18:25:42 -05:00
# if E0_AUTO_FAN_PIN == FAN_PIN
# error "You cannot set E0_AUTO_FAN_PIN equal to FAN_PIN."
# elif E1_AUTO_FAN_PIN == FAN_PIN
# error "You cannot set E1_AUTO_FAN_PIN equal to FAN_PIN."
# elif E2_AUTO_FAN_PIN == FAN_PIN
# error "You cannot set E2_AUTO_FAN_PIN equal to FAN_PIN."
# elif E3_AUTO_FAN_PIN == FAN_PIN
# error "You cannot set E3_AUTO_FAN_PIN equal to FAN_PIN."
2016-07-28 19:08:28 -05:00
# endif
# endif
# endif
2017-05-02 20:18:31 -05:00
# if HAS_FAN0 && CONTROLLER_FAN_PIN == FAN_PIN
# error "You cannot set CONTROLLER_FAN_PIN equal to FAN_PIN."
2016-07-28 19:08:28 -05:00
# endif
2017-05-04 16:38:29 -05:00
# if ENABLED(USE_CONTROLLER_FAN)
2017-05-02 20:18:31 -05:00
# if !HAS_CONTROLLER_FAN
# error "USE_CONTROLLER_FAN requires a CONTROLLER_FAN_PIN. Define in Configuration_adv.h."
# elif E0_AUTO_FAN_PIN == CONTROLLER_FAN_PIN
# error "You cannot set E0_AUTO_FAN_PIN equal to CONTROLLER_FAN_PIN."
# elif E1_AUTO_FAN_PIN == CONTROLLER_FAN_PIN
# error "You cannot set E1_AUTO_FAN_PIN equal to CONTROLLER_FAN_PIN."
# elif E2_AUTO_FAN_PIN == CONTROLLER_FAN_PIN
# error "You cannot set E2_AUTO_FAN_PIN equal to CONTROLLER_FAN_PIN."
# elif E3_AUTO_FAN_PIN == CONTROLLER_FAN_PIN
# error "You cannot set E3_AUTO_FAN_PIN equal to CONTROLLER_FAN_PIN."
2016-07-28 19:08:28 -05:00
# endif
# endif
2018-10-17 15:49:52 -05:00
/**
* Test case light not using the same pin as the fan
*/
# if ENABLED(CASE_LIGHT_ENABLE) && CASE_LIGHT_PIN == FAN_PIN
# error "You cannot set CASE_LIGHT_PIN equal to FAN_PIN."
# endif
2016-07-28 19:08:28 -05:00
/**
* Test Heater , Temp Sensor , and Extruder Pins ; Sensor Type must also be set .
*/
# if !HAS_HEATER_0
# error "HEATER_0_PIN not defined for this board."
2018-11-16 18:20:33 -06:00
# elif !PIN_EXISTS(TEMP_0) && !PIN_EXISTS(MAX6675_SS)
2016-07-28 19:08:28 -05:00
# error "TEMP_0_PIN not defined for this board."
2018-03-01 03:07:39 -06:00
# elif ((defined(__AVR_ATmega644P__) || defined(__AVR_ATmega1284P__)) && (!PIN_EXISTS(E0_STEP) || !PIN_EXISTS(E0_DIR)))
# error "E0_STEP_PIN or E0_DIR_PIN not defined for this board."
# elif ( !(defined(__AVR_ATmega644P__) || defined(__AVR_ATmega1284P__)) && (!PIN_EXISTS(E0_STEP) || !PIN_EXISTS(E0_DIR) || !PIN_EXISTS(E0_ENABLE)))
2016-07-28 19:08:28 -05:00
# error "E0_STEP_PIN, E0_DIR_PIN, or E0_ENABLE_PIN not defined for this board."
# elif TEMP_SENSOR_0 == 0
# error "TEMP_SENSOR_0 is required."
# endif
2017-09-06 06:28:32 -05:00
// Pins are required for heaters
2018-11-16 18:20:33 -06:00
# if ENABLED(HEATER_0_USES_MAX6675) && !PIN_EXISTS(MAX6675_SS)
# error "MAX6675_SS_PIN (required for TEMP_SENSOR_0) not defined for this board."
2017-09-06 06:28:32 -05:00
# elif (HOTENDS > 1 || ENABLED(HEATERS_PARALLEL)) && !HAS_HEATER_1
# error "HEATER_1_PIN not defined for this board."
2016-07-28 19:08:28 -05:00
# endif
# if HOTENDS > 1
2018-11-16 18:20:33 -06:00
# if ENABLED(HEATER_1_USES_MAX6675) && !PIN_EXISTS(MAX6675_SS2)
# error "MAX6675_SS2_PIN (required for TEMP_SENSOR_1) not defined for this board."
# elif TEMP_SENSOR_1 == 0
2016-07-28 19:08:28 -05:00
# error "TEMP_SENSOR_1 is required with 2 or more HOTENDS."
2018-11-16 18:20:33 -06:00
# elif !PIN_EXISTS(TEMP_1) && !PIN_EXISTS(MAX6675_SS2)
2016-07-28 19:08:28 -05:00
# error "TEMP_1_PIN not defined for this board."
# endif
# if HOTENDS > 2
# if TEMP_SENSOR_2 == 0
# error "TEMP_SENSOR_2 is required with 3 or more HOTENDS."
# elif !HAS_HEATER_2
# error "HEATER_2_PIN not defined for this board."
# elif !PIN_EXISTS(TEMP_2)
# error "TEMP_2_PIN not defined for this board."
# endif
# if HOTENDS > 3
# if TEMP_SENSOR_3 == 0
2017-04-06 16:45:29 -05:00
# error "TEMP_SENSOR_3 is required with 4 or more HOTENDS."
2016-07-28 19:08:28 -05:00
# elif !HAS_HEATER_3
# error "HEATER_3_PIN not defined for this board."
# elif !PIN_EXISTS(TEMP_3)
# error "TEMP_3_PIN not defined for this board."
# endif
2017-04-06 16:45:29 -05:00
# if HOTENDS > 4
# if TEMP_SENSOR_4 == 0
2018-11-04 18:36:45 -06:00
# error "TEMP_SENSOR_4 is required with 5 or more HOTENDS."
2017-04-06 16:45:29 -05:00
# elif !HAS_HEATER_4
# error "HEATER_4_PIN not defined for this board."
# elif !PIN_EXISTS(TEMP_4)
# error "TEMP_4_PIN not defined for this board."
# endif
2018-09-13 01:35:55 -05:00
# if HOTENDS > 5
# if TEMP_SENSOR_5 == 0
2018-11-04 18:36:45 -06:00
# error "TEMP_SENSOR_5 is required with 6 HOTENDS."
2018-09-13 01:35:55 -05:00
# elif !HAS_HEATER_5
# error "HEATER_5_PIN not defined for this board."
# elif !PIN_EXISTS(TEMP_5)
# error "TEMP_5_PIN not defined for this board."
# endif
# elif TEMP_SENSOR_5 != 0
# error "TEMP_SENSOR_5 shouldn't be set with only 5 HOTENDS."
# endif
2017-04-06 16:45:29 -05:00
# elif TEMP_SENSOR_4 != 0
2017-10-07 02:27:26 -05:00
# error "TEMP_SENSOR_4 shouldn't be set with only 4 HOTENDS."
2018-09-13 01:35:55 -05:00
# elif TEMP_SENSOR_5 != 0
2018-11-04 18:36:45 -06:00
# error "TEMP_SENSOR_5 shouldn't be set with only 4 HOTENDS."
2017-04-06 16:45:29 -05:00
# endif
2016-07-28 19:08:28 -05:00
# elif TEMP_SENSOR_3 != 0
2017-10-07 02:27:26 -05:00
# error "TEMP_SENSOR_3 shouldn't be set with only 3 HOTENDS."
2017-04-06 16:45:29 -05:00
# elif TEMP_SENSOR_4 != 0
2017-10-07 02:27:26 -05:00
# error "TEMP_SENSOR_4 shouldn't be set with only 3 HOTENDS."
2018-09-13 01:35:55 -05:00
# elif TEMP_SENSOR_5 != 0
2018-11-04 18:36:45 -06:00
# error "TEMP_SENSOR_5 shouldn't be set with only 3 HOTENDS."
2016-07-28 19:08:28 -05:00
# endif
# elif TEMP_SENSOR_2 != 0
2017-10-07 02:27:26 -05:00
# error "TEMP_SENSOR_2 shouldn't be set with only 2 HOTENDS."
2016-07-28 19:08:28 -05:00
# elif TEMP_SENSOR_3 != 0
2017-10-07 02:27:26 -05:00
# error "TEMP_SENSOR_3 shouldn't be set with only 2 HOTENDS."
2017-04-06 16:45:29 -05:00
# elif TEMP_SENSOR_4 != 0
2017-10-07 02:27:26 -05:00
# error "TEMP_SENSOR_4 shouldn't be set with only 2 HOTENDS."
2018-09-13 01:35:55 -05:00
# elif TEMP_SENSOR_5 != 0
# error "TEMP_SENSOR_5 shouldn't be set with only 2 HOTENDS."
2016-07-28 19:08:28 -05:00
# endif
# elif TEMP_SENSOR_1 != 0 && DISABLED(TEMP_SENSOR_1_AS_REDUNDANT)
2017-10-07 02:27:26 -05:00
# error "TEMP_SENSOR_1 shouldn't be set with only 1 HOTEND."
2016-07-28 19:08:28 -05:00
# elif TEMP_SENSOR_2 != 0
2017-10-07 02:27:26 -05:00
# error "TEMP_SENSOR_2 shouldn't be set with only 1 HOTEND."
2016-07-28 19:08:28 -05:00
# elif TEMP_SENSOR_3 != 0
2017-10-07 02:27:26 -05:00
# error "TEMP_SENSOR_3 shouldn't be set with only 1 HOTEND."
2017-04-06 16:45:29 -05:00
# elif TEMP_SENSOR_4 != 0
2017-10-07 02:27:26 -05:00
# error "TEMP_SENSOR_4 shouldn't be set with only 1 HOTEND."
2018-09-13 01:35:55 -05:00
# elif TEMP_SENSOR_5 != 0
# error "TEMP_SENSOR_5 shouldn't be set with only 1 HOTEND."
2016-07-28 19:08:28 -05:00
# endif
# if ENABLED(TEMP_SENSOR_1_AS_REDUNDANT) && TEMP_SENSOR_1 == 0
# error "TEMP_SENSOR_1 is required with TEMP_SENSOR_1_AS_REDUNDANT."
# endif
2016-09-24 16:26:57 -05:00
/**
* Temperature status LEDs
*/
2016-10-22 20:07:48 -05:00
# if ENABLED(TEMP_STAT_LEDS) && !PIN_EXISTS(STAT_LED_RED) && !PIN_EXISTS(STAT_LED_BLUE)
# error "TEMP_STAT_LEDS requires STAT_LED_RED_PIN or STAT_LED_BLUE_PIN, preferably both."
2016-09-24 16:26:57 -05:00
# endif
2018-04-29 18:34:57 -05:00
/**
* LED Control Menu
*/
# if ENABLED(LED_CONTROL_MENU) && !HAS_COLOR_LEDS
# error "LED_CONTROL_MENU requires BLINKM, RGB_LED, RGBW_LED, PCA9632, or NEOPIXEL_LED."
# endif
2016-07-28 19:08:28 -05:00
/**
* Basic 2 - nozzle duplication mode
*/
# if ENABLED(DUAL_NOZZLE_DUPLICATION_MODE)
# if HOTENDS != 2
# error "DUAL_NOZZLE_DUPLICATION_MODE requires exactly 2 hotends."
# elif ENABLED(DUAL_X_CARRIAGE)
# error "DUAL_NOZZLE_DUPLICATION_MODE is incompatible with DUAL_X_CARRIAGE."
# elif ENABLED(SINGLENOZZLE)
# error "DUAL_NOZZLE_DUPLICATION_MODE is incompatible with SINGLENOZZLE."
# elif ENABLED(MIXING_EXTRUDER)
# error "DUAL_NOZZLE_DUPLICATION_MODE is incompatible with MIXING_EXTRUDER."
# elif ENABLED(SWITCHING_EXTRUDER)
# error "DUAL_NOZZLE_DUPLICATION_MODE is incompatible with SWITCHING_EXTRUDER."
# endif
# endif
/**
2017-06-19 16:54:37 -05:00
* Test Extruder Stepper Pins
2016-07-28 19:08:28 -05:00
*/
2017-11-24 16:56:39 -06:00
# if DISABLED(MK2_MULTIPLEXER) // MK2_MULTIPLEXER uses E0 stepper only
2018-09-13 01:35:55 -05:00
# if E_STEPPERS
# if !(PIN_EXISTS(E0_STEP) && PIN_EXISTS(E0_DIR) && PIN_EXISTS(E0_ENABLE))
# error "E0_STEP_PIN, E0_DIR_PIN, or E0_ENABLE_PIN not defined for this board."
2017-11-24 16:56:39 -06:00
# endif
2018-09-13 01:35:55 -05:00
# if E_STEPPERS > 1
# if !(PIN_EXISTS(E1_STEP) && PIN_EXISTS(E1_DIR) && PIN_EXISTS(E1_ENABLE))
# error "E1_STEP_PIN, E1_DIR_PIN, or E1_ENABLE_PIN not defined for this board."
# endif
# if E_STEPPERS > 2
# if !(PIN_EXISTS(E2_STEP) && PIN_EXISTS(E2_DIR) && PIN_EXISTS(E2_ENABLE))
# error "E2_STEP_PIN, E2_DIR_PIN, or E2_ENABLE_PIN not defined for this board."
# endif
# if E_STEPPERS > 3
# if !(PIN_EXISTS(E3_STEP) && PIN_EXISTS(E3_DIR) && PIN_EXISTS(E3_ENABLE))
# error "E3_STEP_PIN, E3_DIR_PIN, or E3_ENABLE_PIN not defined for this board."
# endif
# if E_STEPPERS > 4
# if !(PIN_EXISTS(E4_STEP) && PIN_EXISTS(E4_DIR) && PIN_EXISTS(E4_ENABLE))
# error "E4_STEP_PIN, E4_DIR_PIN, or E4_ENABLE_PIN not defined for this board."
# endif
# if E_STEPPERS > 5
# if !(PIN_EXISTS(E5_STEP) && PIN_EXISTS(E5_DIR) && PIN_EXISTS(E5_ENABLE))
# error "E5_STEP_PIN, E5_DIR_PIN, or E5_ENABLE_PIN not defined for this board."
# endif
# endif // E_STEPPERS > 5
# endif // E_STEPPERS > 4
# endif // E_STEPPERS > 3
# endif // E_STEPPERS > 2
# endif // E_STEPPERS > 1
# endif // E_STEPPERS
2016-07-28 19:08:28 -05:00
# endif
2018-06-19 11:55:49 -05:00
2016-07-28 19:08:28 -05:00
/**
2017-10-29 03:43:44 -05:00
* Endstop Tests
2016-07-28 19:08:28 -05:00
*/
2017-10-29 03:43:44 -05:00
# define _PLUG_UNUSED_TEST(AXIS,PLUG) (DISABLED(USE_##PLUG##MIN_PLUG) && DISABLED(USE_##PLUG##MAX_PLUG) && !(ENABLED(AXIS##_DUAL_ENDSTOPS) && WITHIN(AXIS##2_USE_ENDSTOP, _##PLUG##MAX_, _##PLUG##MIN_)))
# define _AXIS_PLUG_UNUSED_TEST(AXIS) (_PLUG_UNUSED_TEST(AXIS,X) && _PLUG_UNUSED_TEST(AXIS,Y) && _PLUG_UNUSED_TEST(AXIS,Z))
// At least 3 endstop plugs must be used
# if _AXIS_PLUG_UNUSED_TEST(X)
# error "You must enable USE_XMIN_PLUG or USE_XMAX_PLUG."
# endif
# if _AXIS_PLUG_UNUSED_TEST(Y)
# error "You must enable USE_YMIN_PLUG or USE_YMAX_PLUG."
# endif
# if _AXIS_PLUG_UNUSED_TEST(Z)
# error "You must enable USE_ZMIN_PLUG or USE_ZMAX_PLUG."
# endif
// Delta and Cartesian use 3 homing endstops
# if !IS_SCARA
2016-09-05 15:08:26 -05:00
# if X_HOME_DIR < 0 && DISABLED(USE_XMIN_PLUG)
# error "Enable USE_XMIN_PLUG when homing X to MIN."
# elif X_HOME_DIR > 0 && DISABLED(USE_XMAX_PLUG)
# error "Enable USE_XMAX_PLUG when homing X to MAX."
# elif Y_HOME_DIR < 0 && DISABLED(USE_YMIN_PLUG)
# error "Enable USE_YMIN_PLUG when homing Y to MIN."
# elif Y_HOME_DIR > 0 && DISABLED(USE_YMAX_PLUG)
# error "Enable USE_YMAX_PLUG when homing Y to MAX."
2017-10-29 03:43:44 -05:00
# endif
# endif
# if Z_HOME_DIR < 0 && DISABLED(USE_ZMIN_PLUG)
# error "Enable USE_ZMIN_PLUG when homing Z to MIN."
# elif Z_HOME_DIR > 0 && DISABLED(USE_ZMAX_PLUG)
# error "Enable USE_ZMAX_PLUG when homing Z to MAX."
# endif
// Dual endstops requirements
# if ENABLED(X_DUAL_ENDSTOPS)
# if !X2_USE_ENDSTOP
# error "You must set X2_USE_ENDSTOP with X_DUAL_ENDSTOPS."
2018-05-07 03:34:26 -05:00
# elif X2_USE_ENDSTOP == _XMIN_ && DISABLED(USE_XMIN_PLUG)
# error "USE_XMIN_PLUG is required when X2_USE_ENDSTOP is _XMIN_."
# elif X2_USE_ENDSTOP == _XMAX_ && DISABLED(USE_XMAX_PLUG)
# error "USE_XMAX_PLUG is required when X2_USE_ENDSTOP is _XMAX_."
# elif X2_USE_ENDSTOP == _YMIN_ && DISABLED(USE_YMIN_PLUG)
# error "USE_YMIN_PLUG is required when X2_USE_ENDSTOP is _YMIN_."
# elif X2_USE_ENDSTOP == _YMAX_ && DISABLED(USE_YMAX_PLUG)
# error "USE_YMAX_PLUG is required when X2_USE_ENDSTOP is _YMAX_."
# elif X2_USE_ENDSTOP == _ZMIN_ && DISABLED(USE_ZMIN_PLUG)
# error "USE_ZMIN_PLUG is required when X2_USE_ENDSTOP is _ZMIN_."
# elif X2_USE_ENDSTOP == _ZMAX_ && DISABLED(USE_ZMAX_PLUG)
# error "USE_ZMAX_PLUG is required when X2_USE_ENDSTOP is _ZMAX_."
2017-10-29 03:43:44 -05:00
# elif !HAS_X2_MIN && !HAS_X2_MAX
# error "X2_USE_ENDSTOP has been assigned to a nonexistent endstop!"
# elif ENABLED(DELTA)
# error "X_DUAL_ENDSTOPS is not compatible with DELTA."
# endif
# endif
# if ENABLED(Y_DUAL_ENDSTOPS)
# if !Y2_USE_ENDSTOP
# error "You must set Y2_USE_ENDSTOP with Y_DUAL_ENDSTOPS."
2018-05-07 03:34:26 -05:00
# elif Y2_USE_ENDSTOP == _XMIN_ && DISABLED(USE_XMIN_PLUG)
# error "USE_XMIN_PLUG is required when Y2_USE_ENDSTOP is _XMIN_."
# elif Y2_USE_ENDSTOP == _XMAX_ && DISABLED(USE_XMAX_PLUG)
# error "USE_XMAX_PLUG is required when Y2_USE_ENDSTOP is _XMAX_."
# elif Y2_USE_ENDSTOP == _YMIN_ && DISABLED(USE_YMIN_PLUG)
# error "USE_YMIN_PLUG is required when Y2_USE_ENDSTOP is _YMIN_."
# elif Y2_USE_ENDSTOP == _YMAX_ && DISABLED(USE_YMAX_PLUG)
# error "USE_YMAX_PLUG is required when Y2_USE_ENDSTOP is _YMAX_."
# elif Y2_USE_ENDSTOP == _ZMIN_ && DISABLED(USE_ZMIN_PLUG)
# error "USE_ZMIN_PLUG is required when Y2_USE_ENDSTOP is _ZMIN_."
# elif Y2_USE_ENDSTOP == _ZMAX_ && DISABLED(USE_ZMAX_PLUG)
# error "USE_ZMAX_PLUG is required when Y2_USE_ENDSTOP is _ZMAX_."
2017-10-29 03:43:44 -05:00
# elif !HAS_Y2_MIN && !HAS_Y2_MAX
# error "Y2_USE_ENDSTOP has been assigned to a nonexistent endstop!"
# elif ENABLED(DELTA)
# error "Y_DUAL_ENDSTOPS is not compatible with DELTA."
# endif
# endif
# if ENABLED(Z_DUAL_ENDSTOPS)
# if !Z2_USE_ENDSTOP
# error "You must set Z2_USE_ENDSTOP with Z_DUAL_ENDSTOPS."
2018-05-07 03:34:26 -05:00
# elif Z2_USE_ENDSTOP == _XMIN_ && DISABLED(USE_XMIN_PLUG)
# error "USE_XMIN_PLUG is required when Z2_USE_ENDSTOP is _XMIN_."
# elif Z2_USE_ENDSTOP == _XMAX_ && DISABLED(USE_XMAX_PLUG)
# error "USE_XMAX_PLUG is required when Z2_USE_ENDSTOP is _XMAX_."
# elif Z2_USE_ENDSTOP == _YMIN_ && DISABLED(USE_YMIN_PLUG)
# error "USE_YMIN_PLUG is required when Z2_USE_ENDSTOP is _YMIN_."
# elif Z2_USE_ENDSTOP == _YMAX_ && DISABLED(USE_YMAX_PLUG)
# error "USE_YMAX_PLUG is required when Z2_USE_ENDSTOP is _YMAX_."
# elif Z2_USE_ENDSTOP == _ZMIN_ && DISABLED(USE_ZMIN_PLUG)
# error "USE_ZMIN_PLUG is required when Z2_USE_ENDSTOP is _ZMIN_."
# elif Z2_USE_ENDSTOP == _ZMAX_ && DISABLED(USE_ZMAX_PLUG)
# error "USE_ZMAX_PLUG is required when Z2_USE_ENDSTOP is _ZMAX_."
2017-10-29 03:43:44 -05:00
# elif !HAS_Z2_MIN && !HAS_Z2_MAX
# error "Z2_USE_ENDSTOP has been assigned to a nonexistent endstop!"
# elif ENABLED(DELTA)
# error "Z_DUAL_ENDSTOPS is not compatible with DELTA."
2016-09-05 15:08:26 -05:00
# endif
2016-07-28 19:08:28 -05:00
# endif
2018-06-19 11:55:49 -05:00
# if ENABLED(Z_TRIPLE_ENDSTOPS)
# if !Z2_USE_ENDSTOP
# error "You must set Z2_USE_ENDSTOP with Z_TRIPLE_ENDSTOPS."
# elif Z2_USE_ENDSTOP == _XMIN_ && DISABLED(USE_XMIN_PLUG)
# error "USE_XMIN_PLUG is required when Z2_USE_ENDSTOP is _XMIN_."
# elif Z2_USE_ENDSTOP == _XMAX_ && DISABLED(USE_XMAX_PLUG)
# error "USE_XMAX_PLUG is required when Z2_USE_ENDSTOP is _XMAX_."
# elif Z2_USE_ENDSTOP == _YMIN_ && DISABLED(USE_YMIN_PLUG)
# error "USE_YMIN_PLUG is required when Z2_USE_ENDSTOP is _YMIN_."
# elif Z2_USE_ENDSTOP == _YMAX_ && DISABLED(USE_YMAX_PLUG)
# error "USE_YMAX_PLUG is required when Z2_USE_ENDSTOP is _YMAX_."
# elif Z2_USE_ENDSTOP == _ZMIN_ && DISABLED(USE_ZMIN_PLUG)
# error "USE_ZMIN_PLUG is required when Z2_USE_ENDSTOP is _ZMIN_."
# elif Z2_USE_ENDSTOP == _ZMAX_ && DISABLED(USE_ZMAX_PLUG)
# error "USE_ZMAX_PLUG is required when Z2_USE_ENDSTOP is _ZMAX_."
# elif !HAS_Z2_MIN && !HAS_Z2_MAX
# error "Z2_USE_ENDSTOP has been assigned to a nonexistent endstop!"
# elif ENABLED(DELTA)
# error "Z_TRIPLE_ENDSTOPS is not compatible with DELTA."
# endif
# if !Z3_USE_ENDSTOP
# error "You must set Z3_USE_ENDSTOP with Z_TRIPLE_ENDSTOPS."
# elif Z3_USE_ENDSTOP == _XMIN_ && DISABLED(USE_XMIN_PLUG)
# error "USE_XMIN_PLUG is required when Z3_USE_ENDSTOP is _XMIN_."
# elif Z3_USE_ENDSTOP == _XMAX_ && DISABLED(USE_XMAX_PLUG)
# error "USE_XMAX_PLUG is required when Z3_USE_ENDSTOP is _XMAX_."
# elif Z3_USE_ENDSTOP == _YMIN_ && DISABLED(USE_YMIN_PLUG)
# error "USE_YMIN_PLUG is required when Z3_USE_ENDSTOP is _YMIN_."
# elif Z3_USE_ENDSTOP == _YMAX_ && DISABLED(USE_YMAX_PLUG)
# error "USE_YMAX_PLUG is required when Z3_USE_ENDSTOP is _YMAX_."
# elif Z3_USE_ENDSTOP == _ZMIN_ && DISABLED(USE_ZMIN_PLUG)
# error "USE_ZMIN_PLUG is required when Z3_USE_ENDSTOP is _ZMIN_."
# elif Z3_USE_ENDSTOP == _ZMAX_ && DISABLED(USE_ZMAX_PLUG)
# error "USE_ZMAX_PLUG is required when Z3_USE_ENDSTOP is _ZMAX_."
# elif !HAS_Z3_MIN && !HAS_Z3_MAX
# error "Z3_USE_ENDSTOP has been assigned to a nonexistent endstop!"
# elif ENABLED(DELTA)
# error "Z_TRIPLE_ENDSTOPS is not compatible with DELTA."
# endif
# endif
2016-07-28 19:08:28 -05:00
2018-09-24 20:59:12 -05:00
# if defined(ENDSTOP_NOISE_THRESHOLD) && !WITHIN(ENDSTOP_NOISE_THRESHOLD, 2, 7)
# error "ENDSTOP_NOISE_THRESHOLD must be an integer from 2 to 7."
# endif
2016-07-28 19:08:28 -05:00
/**
* emergency - command parser
*/
2018-03-10 22:46:32 -06:00
# if ENABLED(EMERGENCY_PARSER) && defined(__AVR__) && defined(USBCON)
2016-07-28 19:08:28 -05:00
# error "EMERGENCY_PARSER does not work on boards with AT90USB processors (USBCON)."
# endif
2016-08-12 02:51:25 -05:00
/**
* I2C bus
*/
# if ENABLED(EXPERIMENTAL_I2CBUS) && I2C_SLAVE_ADDRESS > 0
# if I2C_SLAVE_ADDRESS < 8
# error "I2C_SLAVE_ADDRESS can't be less than 8. (Addresses 0 - 7 are reserved.)"
# elif I2C_SLAVE_ADDRESS > 127
# error "I2C_SLAVE_ADDRESS can't be over 127. (Only 7 bits allowed.)"
# endif
# endif
2016-09-11 23:33:09 -05:00
2016-09-26 01:30:34 -05:00
/**
* G38 Probe Target
*/
2016-09-29 15:06:01 -05:00
# if ENABLED(G38_PROBE_TARGET)
2016-09-26 01:30:34 -05:00
# if !HAS_BED_PROBE
2016-09-29 15:06:01 -05:00
# error "G38_PROBE_TARGET requires a bed probe."
2016-09-26 01:30:34 -05:00
# elif !IS_CARTESIAN
2016-09-29 15:06:01 -05:00
# error "G38_PROBE_TARGET requires a Cartesian machine."
2016-09-26 01:30:34 -05:00
# endif
# endif
2016-11-29 19:51:13 -06:00
/**
* RGB_LED Requirements
*/
2017-04-11 12:58:55 -05:00
# define _RGB_TEST (PIN_EXISTS(RGB_LED_R) && PIN_EXISTS(RGB_LED_G) && PIN_EXISTS(RGB_LED_B))
2018-10-10 21:25:43 -05:00
# if ENABLED(PRINTER_EVENT_LEDS) && !HAS_COLOR_LEDS
# error "PRINTER_EVENT_LEDS requires BLINKM, PCA9632, RGB_LED, RGBW_LED or NEOPIXEL_LED."
# elif ENABLED(RGB_LED)
2017-04-11 12:58:55 -05:00
# if !_RGB_TEST
2016-11-29 19:51:13 -06:00
# error "RGB_LED requires RGB_LED_R_PIN, RGB_LED_G_PIN, and RGB_LED_B_PIN."
2017-04-11 12:58:55 -05:00
# elif ENABLED(RGBW_LED)
# error "Please enable only one of RGB_LED and RGBW_LED."
2016-11-29 19:51:13 -06:00
# endif
2017-04-11 12:58:55 -05:00
# elif ENABLED(RGBW_LED)
# if !(_RGB_TEST && PIN_EXISTS(RGB_LED_W))
# error "RGBW_LED requires RGB_LED_R_PIN, RGB_LED_G_PIN, RGB_LED_B_PIN, and RGB_LED_W_PIN."
# endif
2017-10-05 06:45:36 -05:00
# elif ENABLED(NEOPIXEL_LED)
2017-07-13 10:01:21 -05:00
# if !(PIN_EXISTS(NEOPIXEL) && NEOPIXEL_PIXELS > 0)
2017-10-05 06:45:36 -05:00
# error "NEOPIXEL_LED requires NEOPIXEL_PIN and NEOPIXEL_PIXELS."
2017-07-13 10:01:21 -05:00
# endif
2016-11-29 19:51:13 -06:00
# endif
2016-10-22 18:26:34 -05:00
/**
* Auto Fan check for PWM pins
*/
# if HAS_AUTO_FAN && EXTRUDER_AUTO_FAN_SPEED != 255
# define AF_ERR_SUFF "_AUTO_FAN_PIN is not a PWM pin. Set EXTRUDER_AUTO_FAN_SPEED to 255."
# if HAS_AUTO_FAN_0
static_assert ( GET_TIMER ( E0_AUTO_FAN_PIN ) , " E0 " AF_ERR_SUFF ) ;
# elif HAS_AUTO_FAN_1
static_assert ( GET_TIMER ( E1_AUTO_FAN_PIN ) , " E1 " AF_ERR_SUFF ) ;
# elif HAS_AUTO_FAN_2
static_assert ( GET_TIMER ( E2_AUTO_FAN_PIN ) , " E2 " AF_ERR_SUFF ) ;
# elif HAS_AUTO_FAN_3
static_assert ( GET_TIMER ( E3_AUTO_FAN_PIN ) , " E3 " AF_ERR_SUFF ) ;
# endif
# endif
2016-09-11 23:33:09 -05:00
/**
* Make sure only one display is enabled
*
* Note : BQ_LCD_SMART_CONTROLLER = > REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
* REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER = > REPRAP_DISCOUNT_SMART_CONTROLLER
* SAV_3DGLCD = > U8GLIB_SH1106 = > ULTIMAKERCONTROLLER
2017-10-09 15:58:02 -05:00
* MKS_12864OLED = > U8GLIB_SH1106 = > ULTIMAKERCONTROLLER
2017-12-16 18:47:04 -06:00
* MKS_12864OLED_SSD1306 = > U8GLIB_SSD1306 = > ULTIMAKERCONTROLLER
2018-03-31 22:52:23 -05:00
* MKS_MINI_12864 = > MINIPANEL
2016-09-11 23:33:09 -05:00
* miniVIKI = > ULTIMAKERCONTROLLER
* VIKI2 = > ULTIMAKERCONTROLLER
* ELB_FULL_GRAPHIC_CONTROLLER = > ULTIMAKERCONTROLLER
2017-10-16 02:33:07 -05:00
* AZSMZ_12864 = > ULTIMAKERCONTROLLER
2016-09-11 23:33:09 -05:00
* PANEL_ONE = > ULTIMAKERCONTROLLER
*/
2018-03-16 02:26:03 -05:00
# if 1 < 0 \
+ ( ENABLED ( ULTIMAKERCONTROLLER ) \
2017-10-09 15:58:02 -05:00
& & DISABLED ( SAV_3DGLCD ) \
& & DISABLED ( miniVIKI ) \
& & DISABLED ( VIKI2 ) \
& & DISABLED ( ELB_FULL_GRAPHIC_CONTROLLER ) \
2017-10-16 02:33:07 -05:00
& & DISABLED ( AZSMZ_12864 ) \
2017-10-09 15:58:02 -05:00
& & DISABLED ( PANEL_ONE ) \
2017-12-16 18:47:04 -06:00
& & DISABLED ( MKS_12864OLED ) \
2018-03-16 02:26:03 -05:00
& & DISABLED ( MKS_12864OLED_SSD1306 ) ) \
+ ( ENABLED ( REPRAP_DISCOUNT_SMART_CONTROLLER ) \
2017-10-09 15:58:02 -05:00
& & DISABLED ( REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER ) \
& & DISABLED ( LCD_FOR_MELZI ) \
& & DISABLED ( MAKEBOARD_MINI_2_LINE_DISPLAY_1602 ) \
2017-12-16 18:47:04 -06:00
& & DISABLED ( MKS_12864OLED ) \
2018-03-16 02:26:03 -05:00
& & DISABLED ( MKS_12864OLED_SSD1306 ) ) \
+ ( ENABLED ( REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER ) & & DISABLED ( BQ_LCD_SMART_CONTROLLER ) ) \
+ ENABLED ( LCD_FOR_MELZI ) \
2018-11-13 01:47:45 -06:00
+ ENABLED ( MALYAN_LCD ) \
2018-03-16 02:26:03 -05:00
+ ENABLED ( MKS_12864OLED ) \
+ ENABLED ( MKS_12864OLED_SSD1306 ) \
+ ENABLED ( MAKEBOARD_MINI_2_LINE_DISPLAY_1602 ) \
+ ENABLED ( CARTESIO_UI ) \
+ ENABLED ( PANEL_ONE ) \
+ ENABLED ( MAKRPANEL ) \
+ ENABLED ( REPRAPWORLD_GRAPHICAL_LCD ) \
+ ENABLED ( VIKI2 ) \
+ ENABLED ( miniVIKI ) \
+ ENABLED ( ELB_FULL_GRAPHIC_CONTROLLER ) \
+ ENABLED ( AZSMZ_12864 ) \
+ ENABLED ( G3D_PANEL ) \
+ ( ENABLED ( MINIPANEL ) & & DISABLED ( MKS_MINI_12864 ) ) \
+ ENABLED ( MKS_MINI_12864 ) \
+ ( ENABLED ( REPRAPWORLD_KEYPAD ) & & DISABLED ( CARTESIO_UI ) & & DISABLED ( ZONESTAR_LCD ) ) \
+ ENABLED ( RIGIDBOT_PANEL ) \
+ ENABLED ( RA_CONTROL_PANEL ) \
+ ENABLED ( LCD_SAINSMART_I2C_1602 ) \
+ ENABLED ( LCD_SAINSMART_I2C_2004 ) \
+ ENABLED ( LCM1602 ) \
+ ENABLED ( LCD_I2C_PANELOLU2 ) \
+ ENABLED ( LCD_I2C_VIKI ) \
+ ( ENABLED ( U8GLIB_SSD1306 ) & & DISABLED ( OLED_PANEL_TINYBOY2 ) & & DISABLED ( MKS_12864OLED_SSD1306 ) ) \
+ ENABLED ( SAV_3DLCD ) \
+ ENABLED ( BQ_LCD_SMART_CONTROLLER ) \
+ ENABLED ( SAV_3DGLCD ) \
+ ENABLED ( OLED_PANEL_TINYBOY2 ) \
+ ENABLED ( ZONESTAR_LCD ) \
+ ENABLED ( ULTI_CONTROLLER )
# error "Please select no more than one LCD controller option."
# endif
2017-04-13 06:25:43 -05:00
2017-06-06 07:19:27 -05:00
/**
2018-07-14 06:13:06 -05:00
* Check existing CS pins against enabled TMC SPI drivers .
2018-03-13 02:06:40 -05:00
*/
2018-11-02 01:06:06 -05:00
# define INVALID_TMC2130(ST) (AXIS_DRIVER_TYPE(ST, TMC2130) && !PIN_EXISTS(ST##_CS))
# if INVALID_TMC2130(X)
2018-11-01 16:13:33 -05:00
# error "TMC2130 on X requires X_CS_PIN."
2018-11-02 01:06:06 -05:00
# elif INVALID_TMC2130(X2)
2018-11-01 16:13:33 -05:00
# error "TMC2130 on X2 requires X2_CS_PIN."
2018-11-02 01:06:06 -05:00
# elif INVALID_TMC2130(Y)
2018-11-01 16:13:33 -05:00
# error "TMC2130 on Y requires Y_CS_PIN."
2018-11-02 01:06:06 -05:00
# elif INVALID_TMC2130(Y2)
2018-11-01 16:13:33 -05:00
# error "TMC2130 on Y2 requires Y2_CS_PIN."
2018-11-02 01:06:06 -05:00
# elif INVALID_TMC2130(Z)
2018-11-01 16:13:33 -05:00
# error "TMC2130 on Z requires Z_CS_PIN."
2018-11-02 01:06:06 -05:00
# elif INVALID_TMC2130(Z2)
2018-11-01 16:13:33 -05:00
# error "TMC2130 on Z2 requires Z2_CS_PIN."
2018-11-02 01:06:06 -05:00
# elif INVALID_TMC2130(Z3)
2018-11-01 16:13:33 -05:00
# error "TMC2130 on Z3 requires Z3_CS_PIN."
2018-11-02 01:06:06 -05:00
# elif INVALID_TMC2130(E0)
2018-11-01 16:13:33 -05:00
# error "TMC2130 on E0 requires E0_CS_PIN."
2018-11-02 01:06:06 -05:00
# elif INVALID_TMC2130(E1)
2018-11-01 16:13:33 -05:00
# error "TMC2130 on E1 requires E1_CS_PIN."
2018-11-02 01:06:06 -05:00
# elif INVALID_TMC2130(E2)
2018-11-01 16:13:33 -05:00
# error "TMC2130 on E2 requires E2_CS_PIN."
2018-11-02 01:06:06 -05:00
# elif INVALID_TMC2130(E3)
2018-11-01 16:13:33 -05:00
# error "TMC2130 on E3 requires E3_CS_PIN."
2018-11-02 01:06:06 -05:00
# elif INVALID_TMC2130(E4)
2018-11-01 16:13:33 -05:00
# error "TMC2130 on E4 requires E4_CS_PIN."
2018-11-02 01:06:06 -05:00
# elif INVALID_TMC2130(E5)
2018-11-01 16:13:33 -05:00
# error "TMC2130 on E5 requires E5_CS_PIN."
# endif
2018-11-02 01:06:06 -05:00
# undef INVALID_TMC2130
2018-11-01 16:13:33 -05:00
/**
* Check existing RX / TX pins against enable TMC UART drivers .
*/
2018-11-02 01:06:06 -05:00
# define INVALID_TMC2208(ST) (AXIS_DRIVER_TYPE(ST, TMC2208) && !(defined(ST##_HARDWARE_SERIAL) || (PIN_EXISTS(ST##_SERIAL_RX) && PIN_EXISTS(ST##_SERIAL_TX))))
# if INVALID_TMC2208(X)
# error "TMC2208 on X requires X_HARDWARE_SERIAL or X_SERIAL_(RX|TX)_PIN."
# elif INVALID_TMC2208(X2)
# error "TMC2208 on X2 requires X2_HARDWARE_SERIAL or X2_SERIAL_(RX|TX)_PIN."
# elif INVALID_TMC2208(Y)
# error "TMC2208 on Y requires Y_HARDWARE_SERIAL or Y_SERIAL_(RX|TX)_PIN."
# elif INVALID_TMC2208(Y2)
# error "TMC2208 on Y2 requires Y2_HARDWARE_SERIAL or Y2_SERIAL_(RX|TX)_PIN."
# elif INVALID_TMC2208(Z)
# error "TMC2208 on Z requires Z_HARDWARE_SERIAL or Z_SERIAL_(RX|TX)_PIN."
# elif INVALID_TMC2208(Z2)
# error "TMC2208 on Z2 requires Z2_HARDWARE_SERIAL or Z2_SERIAL_(RX|TX)_PIN."
# elif INVALID_TMC2208(Z3)
# error "TMC2208 on Z3 requires Z3_HARDWARE_SERIAL or Z3_SERIAL_(RX|TX)_PIN."
# elif INVALID_TMC2208(E0)
# error "TMC2208 on E0 requires E0_HARDWARE_SERIAL or E0_SERIAL_(RX|TX)_PIN."
# elif INVALID_TMC2208(E1)
# error "TMC2208 on E1 requires E1_HARDWARE_SERIAL or E1_SERIAL_(RX|TX)_PIN."
# elif INVALID_TMC2208(E2)
# error "TMC2208 on E2 requires E2_HARDWARE_SERIAL or E2_SERIAL_(RX|TX)_PIN."
# elif INVALID_TMC2208(E3)
# error "TMC2208 on E3 requires E3_HARDWARE_SERIAL or E3_SERIAL_(RX|TX)_PIN."
# elif INVALID_TMC2208(E4)
# error "TMC2208 on E4 requires E4_HARDWARE_SERIAL or E4_SERIAL_(RX|TX)_PIN."
# elif INVALID_TMC2208(E5)
# error "TMC2208 on E5 requires E5_HARDWARE_SERIAL or E5_SERIAL_(RX|TX)_PIN."
# endif
# undef INVALID_TMC2208
2018-03-24 14:26:11 -05:00
/**
* TMC2208 software UART and ENDSTOP_INTERRUPTS both use pin change interrupts ( PCI )
*/
2018-07-14 06:13:06 -05:00
# if HAS_DRIVER(TMC2208) && ENABLED(ENDSTOP_INTERRUPTS_FEATURE) && !( \
2018-03-24 14:26:11 -05:00
defined ( X_HARDWARE_SERIAL ) \
| | defined ( X2_HARDWARE_SERIAL ) \
| | defined ( Y_HARDWARE_SERIAL ) \
| | defined ( Y2_HARDWARE_SERIAL ) \
| | defined ( Z_HARDWARE_SERIAL ) \
| | defined ( Z2_HARDWARE_SERIAL ) \
2018-06-19 11:55:49 -05:00
| | defined ( Z3_HARDWARE_SERIAL ) \
2018-03-24 14:26:11 -05:00
| | defined ( E0_HARDWARE_SERIAL ) \
| | defined ( E1_HARDWARE_SERIAL ) \
| | defined ( E2_HARDWARE_SERIAL ) \
| | defined ( E3_HARDWARE_SERIAL ) \
2018-09-13 01:35:55 -05:00
| | defined ( E4_HARDWARE_SERIAL ) \
| | defined ( E5_HARDWARE_SERIAL ) )
# error "Select hardware UART for TMC2208 to use both TMC2208 and ENDSTOP_INTERRUPTS_FEATURE."
2018-03-16 02:26:03 -05:00
# endif
2018-09-01 15:24:44 -05:00
/**
* TMC2208 software UART is only supported on AVR
*/
2018-09-08 20:41:21 -05:00
# if HAS_DRIVER(TMC2208) && !defined(__AVR__) && !defined(TARGET_LPC1768) && !( \
2018-09-01 15:24:44 -05:00
defined ( X_HARDWARE_SERIAL ) \
| | defined ( X2_HARDWARE_SERIAL ) \
| | defined ( Y_HARDWARE_SERIAL ) \
| | defined ( Y2_HARDWARE_SERIAL ) \
| | defined ( Z_HARDWARE_SERIAL ) \
| | defined ( Z2_HARDWARE_SERIAL ) \
| | defined ( E0_HARDWARE_SERIAL ) \
| | defined ( E1_HARDWARE_SERIAL ) \
| | defined ( E2_HARDWARE_SERIAL ) \
| | defined ( E3_HARDWARE_SERIAL ) \
2018-09-13 01:35:55 -05:00
| | defined ( E4_HARDWARE_SERIAL ) \
| | defined ( E5_HARDWARE_SERIAL ) )
2018-09-08 20:41:21 -05:00
# error "TMC2208 Software Serial is supported only on AVR and LPC1768 platforms."
2018-09-01 15:24:44 -05:00
# endif
2018-07-14 06:13:06 -05:00
# if ENABLED(SENSORLESS_HOMING)
// Require STEALTHCHOP for SENSORLESS_HOMING on DELTA as the transition from spreadCycle to stealthChop
// is necessary in order to reset the stallGuard indication between the initial movement of all three
// towers to +Z and the individual homing of each tower. This restriction can be removed once a means of
// clearing the stallGuard activated status is found.
2018-12-07 15:34:21 -06:00
# if ENABLED(DELTA) && !(ENABLED(STEALTHCHOP_XY) && ENABLED(STEALTHCHOP_Z))
# error "SENSORLESS_HOMING on DELTA currently requires STEALTHCHOP_XY and STEALTHCHOP_Z."
2018-10-16 05:46:33 -05:00
# elif X_SENSORLESS && X_HOME_DIR == -1 && (!X_MIN_ENDSTOP_INVERTING || DISABLED(ENDSTOPPULLUP_XMIN))
2018-07-14 06:13:06 -05:00
# error "SENSORLESS_HOMING requires X_MIN_ENDSTOP_INVERTING and ENDSTOPPULLUP_XMIN when homing to X_MIN."
2018-10-16 05:46:33 -05:00
# elif X_SENSORLESS && X_HOME_DIR == 1 && (!X_MAX_ENDSTOP_INVERTING || DISABLED(ENDSTOPPULLUP_XMAX))
2018-07-14 06:13:06 -05:00
# error "SENSORLESS_HOMING requires X_MAX_ENDSTOP_INVERTING and ENDSTOPPULLUP_XMAX when homing to X_MAX."
2018-10-16 05:46:33 -05:00
# elif Y_SENSORLESS && Y_HOME_DIR == -1 && (!Y_MIN_ENDSTOP_INVERTING || DISABLED(ENDSTOPPULLUP_YMIN))
2018-07-14 06:13:06 -05:00
# error "SENSORLESS_HOMING requires Y_MIN_ENDSTOP_INVERTING and ENDSTOPPULLUP_YMIN when homing to Y_MIN."
2018-10-16 05:46:33 -05:00
# elif Y_SENSORLESS && Y_HOME_DIR == 1 && (!Y_MAX_ENDSTOP_INVERTING || DISABLED(ENDSTOPPULLUP_YMAX))
2018-07-14 06:13:06 -05:00
# error "SENSORLESS_HOMING requires Y_MAX_ENDSTOP_INVERTING and ENDSTOPPULLUP_YMAX when homing to Y_MAX."
2018-10-16 05:46:33 -05:00
# elif Z_SENSORLESS && Z_HOME_DIR == -1 && (!Z_MIN_ENDSTOP_INVERTING || DISABLED(ENDSTOPPULLUP_ZMIN))
2018-07-14 06:13:06 -05:00
# error "SENSORLESS_HOMING requires Z_MIN_ENDSTOP_INVERTING and ENDSTOPPULLUP_ZMIN when homing to Z_MIN."
2018-10-16 05:46:33 -05:00
# elif Z_SENSORLESS && Z_HOME_DIR == 1 && (!Z_MAX_ENDSTOP_INVERTING || DISABLED(ENDSTOPPULLUP_ZMAX))
2018-07-14 06:13:06 -05:00
# error "SENSORLESS_HOMING requires Z_MAX_ENDSTOP_INVERTING and ENDSTOPPULLUP_ZMAX when homing to Z_MAX."
2018-09-24 20:59:12 -05:00
# elif ENDSTOP_NOISE_THRESHOLD
# error "SENSORLESS_HOMING is incompatible with ENDSTOP_NOISE_THRESHOLD."
2018-07-14 06:13:06 -05:00
# endif
2017-12-29 13:38:08 -06:00
# endif
2018-11-01 16:13:33 -05:00
// Sensorless homing/probing requirements
# if ENABLED(SENSORLESS_HOMING) && !(X_SENSORLESS || Y_SENSORLESS || Z_SENSORLESS)
# error "SENSORLESS_HOMING requires a TMC stepper driver with StallGuard on X, Y, or Z axes."
# elif ENABLED(SENSORLESS_PROBING) && ENABLED(DELTA) && !(X_SENSORLESS && Y_SENSORLESS && Z_SENSORLESS)
# error "SENSORLESS_PROBING for DELTA requires TMC stepper drivers with StallGuard on X, Y, and Z axes."
# elif ENABLED(SENSORLESS_PROBING) && !Z_SENSORLESS
# error "SENSORLESS_PROBING requires a TMC stepper driver with StallGuard on Z."
# endif
2018-07-14 06:13:06 -05:00
// Sensorless homing is required for both combined steppers in an H-bot
# if CORE_IS_XY && X_SENSORLESS != Y_SENSORLESS
# error "CoreXY requires both X and Y to use sensorless homing if either does."
# elif CORE_IS_XZ && X_SENSORLESS != Z_SENSORLESS
# error "CoreXZ requires both X and Z to use sensorless homing if either does."
# elif CORE_IS_YZ && Y_SENSORLESS != Z_SENSORLESS
# error "CoreYZ requires both Y and Z to use sensorless homing if either does."
2017-04-14 22:43:56 -05:00
# endif
2018-09-09 14:59:12 -05:00
// Other TMC feature requirements
2018-12-07 15:34:21 -06:00
# if ENABLED(HYBRID_THRESHOLD) && !STEALTHCHOP_ENABLED
# error "Enable STEALTHCHOP_(XY|Z|E) to use HYBRID_THRESHOLD."
2018-09-09 14:59:12 -05:00
# elif ENABLED(TMC_Z_CALIBRATION) && !AXIS_IS_TMC(Z) && !AXIS_IS_TMC(Z2) && !AXIS_IS_TMC(Z3)
2018-07-14 06:13:06 -05:00
# error "TMC_Z_CALIBRATION requires at least one TMC driver on Z axis"
2018-09-09 14:59:12 -05:00
# elif ENABLED(SENSORLESS_HOMING) && !HAS_STALLGUARD
# error "SENSORLESS_HOMING requires TMC2130 stepper drivers."
# elif ENABLED(SENSORLESS_PROBING) && !HAS_STALLGUARD
# error "SENSORLESS_PROBING requires TMC2130 stepper drivers."
2018-12-07 15:34:21 -06:00
# elif STEALTHCHOP_ENABLED && !HAS_STEALTHCHOP
2018-07-14 06:13:06 -05:00
# error "STEALTHCHOP requires TMC2130 or TMC2208 stepper drivers."
2018-09-09 14:59:12 -05:00
# endif
2018-03-13 02:06:40 -05:00
2018-12-07 15:34:21 -06:00
# if ENABLED(DELTA) && (ENABLED(STEALTHCHOP_XY) != ENABLED(STEALTHCHOP_Z))
# error "STEALTHCHOP_XY and STEALTHCHOP_Z must be the same on DELTA."
# endif
2017-10-09 15:58:02 -05:00
/**
* Digipot requirement
*/
# if ENABLED(DIGIPOT_MCP4018)
# if !defined(DIGIPOTS_I2C_SDA_X) || !defined(DIGIPOTS_I2C_SDA_Y) || !defined(DIGIPOTS_I2C_SDA_Z) \
| | ! defined ( DIGIPOTS_I2C_SDA_E0 ) | | ! defined ( DIGIPOTS_I2C_SDA_E1 )
# error "DIGIPOT_MCP4018 requires DIGIPOTS_I2C_SDA_* pins to be defined."
# endif
# endif
2017-04-13 06:25:43 -05:00
/**
2018-12-07 19:37:12 -06:00
* Check per - axis initializers for errors
2017-04-13 06:25:43 -05:00
*/
constexpr float sanity_arr_1 [ ] = DEFAULT_AXIS_STEPS_PER_UNIT ,
sanity_arr_2 [ ] = DEFAULT_MAX_FEEDRATE ,
sanity_arr_3 [ ] = DEFAULT_MAX_ACCELERATION ;
2018-12-07 19:37:12 -06:00
2017-04-13 06:25:43 -05:00
static_assert ( COUNT ( sanity_arr_1 ) > = XYZE , " DEFAULT_AXIS_STEPS_PER_UNIT requires 4 (or more) elements. " ) ;
2018-11-04 18:42:36 -06:00
static_assert ( COUNT ( sanity_arr_1 ) < = XYZE_N , " DEFAULT_AXIS_STEPS_PER_UNIT has too many elements. (Did you forget to enable DISTINCT_E_FACTORS?) " ) ;
2018-12-07 19:37:12 -06:00
static_assert ( sanity_arr_1 [ 0 ] > 0 & & sanity_arr_1 [ 1 ] > 0 & & sanity_arr_1 [ 2 ] > 0
& & ( XYZE_N < = 3 | | sanity_arr_1 [ 3 ] > 0 ) & & ( XYZE_N < = 4 | | sanity_arr_1 [ 4 ] > 0 )
& & ( XYZE_N < = 5 | | sanity_arr_1 [ 5 ] > 0 ) & & ( XYZE_N < = 6 | | sanity_arr_1 [ 6 ] > 0 )
& & ( XYZE_N < = 7 | | sanity_arr_1 [ 7 ] > 0 ) & & ( XYZE_N < = 8 | | sanity_arr_1 [ 8 ] > 0 ) ,
" DEFAULT_AXIS_STEPS_PER_UNIT values must be positive. " ) ;
static_assert ( COUNT ( sanity_arr_2 ) > = XYZE , " DEFAULT_MAX_FEEDRATE requires 4 (or more) elements. " ) ;
2018-11-04 18:42:36 -06:00
static_assert ( COUNT ( sanity_arr_2 ) < = XYZE_N , " DEFAULT_MAX_FEEDRATE has too many elements. (Did you forget to enable DISTINCT_E_FACTORS?) " ) ;
2018-12-07 19:37:12 -06:00
static_assert ( sanity_arr_2 [ 0 ] > 0 & & sanity_arr_2 [ 1 ] > 0 & & sanity_arr_2 [ 2 ] > 0
& & ( XYZE_N < = 3 | | sanity_arr_2 [ 3 ] > 0 ) & & ( XYZE_N < = 4 | | sanity_arr_2 [ 4 ] > 0 )
& & ( XYZE_N < = 5 | | sanity_arr_2 [ 5 ] > 0 ) & & ( XYZE_N < = 6 | | sanity_arr_2 [ 6 ] > 0 )
& & ( XYZE_N < = 7 | | sanity_arr_2 [ 7 ] > 0 ) & & ( XYZE_N < = 8 | | sanity_arr_2 [ 8 ] > 0 ) ,
" DEFAULT_MAX_FEEDRATE values must be positive. " ) ;
static_assert ( COUNT ( sanity_arr_3 ) > = XYZE , " DEFAULT_MAX_ACCELERATION requires 4 (or more) elements. " ) ;
2018-11-04 18:42:36 -06:00
static_assert ( COUNT ( sanity_arr_3 ) < = XYZE_N , " DEFAULT_MAX_ACCELERATION has too many elements. (Did you forget to enable DISTINCT_E_FACTORS?) " ) ;
2018-12-07 19:37:12 -06:00
static_assert ( sanity_arr_3 [ 0 ] > 0 & & sanity_arr_3 [ 1 ] > 0 & & sanity_arr_3 [ 2 ] > 0
& & ( XYZE_N < = 3 | | sanity_arr_3 [ 3 ] > 0 ) & & ( XYZE_N < = 4 | | sanity_arr_3 [ 4 ] > 0 )
& & ( XYZE_N < = 5 | | sanity_arr_3 [ 5 ] > 0 ) & & ( XYZE_N < = 6 | | sanity_arr_3 [ 6 ] > 0 )
& & ( XYZE_N < = 7 | | sanity_arr_3 [ 7 ] > 0 ) & & ( XYZE_N < = 8 | | sanity_arr_3 [ 8 ] > 0 ) ,
" DEFAULT_MAX_ACCELERATION values must be positive. " ) ;
2017-04-07 13:52:05 -05:00
2017-11-04 16:36:41 -05:00
# if ENABLED(CNC_COORDINATE_SYSTEMS) && ENABLED(NO_WORKSPACE_OFFSETS)
# error "CNC_COORDINATE_SYSTEMS is incompatible with NO_WORKSPACE_OFFSETS."
# endif
2017-11-26 17:36:40 -06:00
# if !BLOCK_BUFFER_SIZE || !IS_POWER_OF_2(BLOCK_BUFFER_SIZE)
# error "BLOCK_BUFFER_SIZE must be a power of 2."
# endif
2017-11-28 01:05:51 -06:00
# if ENABLED(LED_CONTROL_MENU) && DISABLED(ULTIPANEL)
# error "LED_CONTROL_MENU requires an LCD controller."
# endif
2017-10-19 00:43:07 -05:00
2018-01-20 16:58:41 -06:00
# if ENABLED(CASE_LIGHT_USE_NEOPIXEL) && DISABLED(NEOPIXEL_LED)
# error "CASE_LIGHT_USE_NEOPIXEL requires NEOPIXEL_LED."
# endif
2017-12-01 16:42:23 -06:00
# if ENABLED(SKEW_CORRECTION)
# if !defined(XY_SKEW_FACTOR) && !(defined(XY_DIAG_AC) && defined(XY_DIAG_BD) && defined(XY_SIDE_AD))
# error "SKEW_CORRECTION requires XY_SKEW_FACTOR or XY_DIAG_AC, XY_DIAG_BD, XY_SIDE_AD."
# endif
# if ENABLED(SKEW_CORRECTION_FOR_Z)
# if !defined(XZ_SKEW_FACTOR) && !(defined(XZ_DIAG_AC) && defined(XZ_DIAG_BD) && defined(XZ_SIDE_AD))
# error "SKEW_CORRECTION requires XZ_SKEW_FACTOR or XZ_DIAG_AC, XZ_DIAG_BD, XZ_SIDE_AD."
# endif
# if !defined(YZ_SKEW_FACTOR) && !(defined(YZ_DIAG_AC) && defined(YZ_DIAG_BD) && defined(YZ_SIDE_AD))
# error "SKEW_CORRECTION requires YZ_SKEW_FACTOR or YZ_DIAG_AC, YZ_DIAG_BD, YZ_SIDE_AD."
# endif
# endif
# endif
2018-08-24 16:35:55 -05:00
# if ENABLED(POWER_LOSS_RECOVERY) && DISABLED(ULTIPANEL)
2018-04-21 19:41:26 -05:00
# error "POWER_LOSS_RECOVERY currently requires an LCD Controller."
# endif
2018-05-20 11:37:55 -05:00
# if ENABLED(FAST_PWM_FAN) && !(defined(ARDUINO) && !defined(ARDUINO_ARCH_SAM))
# error "FAST_PWM_FAN only supported by 8 bit CPUs."
# endif
2018-10-29 14:01:36 -05:00
# if ENABLED(Z_STEPPER_AUTO_ALIGN)
# if !Z_MULTI_STEPPER_DRIVERS
# error "Z_STEPPER_AUTO_ALIGN requires Z_DUAL_STEPPER_DRIVERS or Z_TRIPLE_STEPPER_DRIVERS."
# elif !HAS_BED_PROBE
# error "Z_STEPPER_AUTO_ALIGN requires a Z-bed probe."
# endif
constexpr float sanity_arr_z_align_x [ ] = Z_STEPPER_ALIGN_X , sanity_arr_z_align_y [ ] = Z_STEPPER_ALIGN_Y ;
static_assert (
COUNT ( sanity_arr_z_align_x ) = = Z_STEPPER_COUNT & & COUNT ( sanity_arr_z_align_y ) = = Z_STEPPER_COUNT ,
" Z_STEPPER_ALIGN_[XY]POS settings require one element per Z stepper. "
) ;
# endif
2018-08-31 17:40:39 -05:00
# if ENABLED(PRINTCOUNTER) && DISABLED(EEPROM_SETTINGS)
# error "PRINTCOUNTER requires EEPROM_SETTINGS. Please update your Configuration."
# endif
2018-07-02 10:06:17 -05:00
# if ENABLED(USB_FLASH_DRIVE_SUPPORT) && !(PIN_EXISTS(USB_CS) && PIN_EXISTS(USB_INTR))
# error "USB_CS_PIN and USB_INTR_PIN are required for USB_FLASH_DRIVE_SUPPORT."
# endif
2018-10-09 20:00:47 -05:00
# if ENABLED(SD_FIRMWARE_UPDATE) && !defined(__AVR_ATmega2560__)
# error "SD_FIRMWARE_UPDATE requires an ATmega2560-based (Arduino Mega) board."
# endif
2018-11-09 05:25:08 -06:00
# if ENABLED(GCODE_MACROS) && !WITHIN(GCODE_MACROS_SLOTS, 1, 10)
# error "GCODE_MACROS_SLOTS must be a number from 1 to 10."
# endif
2018-12-08 14:36:46 -06:00
# if ENABLED(BACKLASH_COMPENSATION) && IS_CORE
# error "BACKLASH_COMPENSATION is incompatible with CORE kinematics."
# endif
