bissen21/Marlin_Firmware
1
0
Fork 0
Code Issues Pull Requests Projects Releases 4 Wiki Activity
6,803 Commits 1 Branch 4 Tags 151 MiB
72fe995c42
Commit Graph

1673 Commits

Author SHA1 Message Date
maverikou
0f034dd97e Clean up Z_RAISE_AFTER_PROBING to work the same in all code paths except Z_PROBE_SLED. 2015-03-22 13:54:45 +02:00
maverikou
6c96f32069 Blind fix for #1507 2015-03-22 13:54:21 +02:00
Josef Larsson
379348487e Removed malplaced comment. 2015-03-22 12:21:31 +01:00
Josef Larsson
9b3462f73f Refactor SCARA calibration. Save some lines of code and possibly ROM. 2015-03-22 00:37:24 +01:00
Scott Lahteine
691e753cc3 Don't add home offsets in G29 
- Address #1262 by leaving values as set
- Rename `add_homing` to `home_offset`
 2015-03-21 16:30:02 -07:00
Scott Lahteine
15eb5d35a2 Merge branch 'Development' into config_testing 
Latest upstream commits
 2015-03-21 15:42:45 -07:00
Edward Patel
3d0a060a7a Added G29 command 2015-03-21 14:50:47 +01:00
Scott Lahteine
63d5d28085 Merge branch 'Development' into config_testing 
Latest upstream changes
 2015-03-20 04:15:18 -07:00
Edward Patel
4619d80524 Merge branch 'Development' into manual-bed-leveling+mesh-bed-level 2015-03-20 11:45:06 +01:00
Scott Lahteine
2424713a8f Merge pull request #1640 from AnHardt/warning6 
codepos not used in gcode_M28()
 2015-03-20 02:58:00 -07:00
Scott Lahteine
670006b919 Remove invariant code from Configurations 
- Add `Conditionals.h` with calculated configuration values
- Add `SanityCheck.h` with checks for configuration errors
- Remove equivalent code from all configurations
- Move error checks from some sources to `SanityCheck.h` also
- Fix initialization of count_direction in stepper.cpp
 2015-03-19 22:22:23 -07:00
Edward Patel
a61f679568 Merge branch 'Development' into manual-bed-leveling+mesh-bed-level 2015-03-20 02:28:35 +01:00
Edward Patel
c87faa69ed Shortened mesh_plan_buffer_line() 2015-03-20 02:18:49 +01:00
AnHardt
ae01a6b5f2 Make use of codepos. 
Saves one addition.
Needs one pointer on the stack.

Don't know if this is a go trade.
 2015-03-19 09:45:16 +01:00
Scott Lahteine
80e0ee10ca Merge pull request #1631 from AnHardt/iss1593 
Decrease KILL_DELAY
 2015-03-18 19:10:38 -07:00
Scott Lahteine
76127b8a55 Merge pull request #1630 from Wurstnase/fix_g29 
optional parameters must be named when ignoring order
 2015-03-18 19:09:40 -07:00
Scott Lahteine
8664c6d465 Merge pull request #1638 from AnHardt/warning4 
delta[3] not used when DELTA not defined.
 2015-03-18 19:07:55 -07:00
Scott Lahteine
10711ccc6a Merge pull request #1639 from AnHardt/warning5 
G4 could wait for an undefined time
 2015-03-18 19:07:14 -07:00
Edward Patel
240b5cfe04 Merge branch 'Development' into manual-bed-leveling+mesh-bed-level 2015-03-18 19:19:46 +01:00
alexborro
4521f6655b Restore "S" parameter of M204 for retrocompatibility. 2015-03-18 12:19:30 -03:00
alexborro
5ddb8d94e2 Update Documentation related to M204 2015-03-18 11:09:10 -03:00
AnHardt
f8c4d43886 delta[3] is used with SCARA 
Shoot in the dark.
 2015-03-18 12:14:49 +01:00
AnHardt
72a9fed4fb codepos not used in gcode_M28() 
Got:
Marlin_main.cpp:2567: warning: unused variable 'codepos'

Needs revision.
Don't now how this should look like.
 2015-03-18 11:41:14 +01:00
AnHardt
b94dd33641 G4 could wait for an undefined time 
Got:
Marlin_main.cpp:1689: warning: 'codenum' may be used uninitialized in this function

And indeed codenum is undefined when no parameter is given.
 2015-03-18 11:23:41 +01:00
AnHardt
e90985a4e8 delta[3] not used when DELTA not defined. 
got:
Marlin_main.cpp:387: warning: 'delta' defined but not used

Compiles cleaner when definition is removed.
 2015-03-18 11:11:49 +01:00
AnHardt
d1658eebfc Decrease KILL_DELAY 
Users hat to press kill-button for unexpexted lon times.
See #1593
 2015-03-18 01:45:42 +01:00
Wurstnase
00adb2a6c1 optional parameters must be named when ignoring order 2015-03-18 01:02:29 +01:00
Edward Patel
0d43898a22 Remove of mesh_plan_buffer_line parameter reference (e) 2015-03-17 22:55:29 +01:00
Edward Patel
8067a985ce Merge branch 'Development' into manual-bed-leveling+mesh-bed-level 
Fixed conflicts:
	Marlin/planner.h
 2015-03-17 22:48:08 +01:00
maverikou
3570447ded Fix Z_RAISE_AFTER_PROBING 2015-03-16 08:35:49 +02:00
maverikou
8a739b6fba Merge branch 'Development' into delta_auto_bed_level 
Conflicts:
	Marlin/Marlin_main.cpp
 2015-03-16 08:24:26 +02:00
Scott Lahteine
a686c9878f Move TOPO_ORIGIN define to Configuration.h 
- Addressing issue #1608
 2015-03-15 15:49:36 -07:00
Edward Patel
8005d22c81 Added menu option for bed leveling. 2015-03-15 23:24:32 +01:00
Edward Patel
0e51e53813 WIP. Adding bed leveling code. 2015-03-15 23:24:32 +01:00
Scott Lahteine
7bc77dc134 Merge pull request #1583 from galexander1/m404fix 
M404 should not use 'N' address as parameter because 'N' is reserved
 2015-03-15 07:47:30 -07:00
Scott Lahteine
b80ed51fcc Fix controllerFan() code 
- Add support for 4th extruder
- Fix parentheses matching
- Apply coding standards
- Address issue mentioned at #1575
 2015-03-15 06:55:31 -07:00
Scott Lahteine
bb4cb1b15a Merge pull request #1606 from thinkyhead/cleanup_stepper 
Cleanup of stepper.cpp
 2015-03-15 06:05:08 -07:00
alexborro
d3259d0dba Merge pull request #1581 from msutas/Development 
Filament Runout Sensor Feature
 2015-03-14 18:35:20 -03:00
Scott Lahteine
c37f7d15c9 - Rename WRITE_E_STEP for consistency 
- Add BIT and TEST macros
- Add _APPLY_ macros to stepper.cpp to help with consolidation
- Consolidate code in stepper.cpp using macros
- Apply standards in stepper.cpp
- Use >= 0 instead of > -1 as a better semantic
- Replace DUAL_Y_CARRIAGE with Y_DUAL_STEPPER_DRIVERS
 2015-03-14 04:28:22 -07:00
alexborro
2f3c77b751 Fix decimal places in G29 Bed Equation Coeficients 2015-03-13 14:39:41 -03:00
Scott Lahteine
e4d77a6313 Merge pull request #1554 from 2PrintBeta/Development 
Macro indirection for stepper drivers + Support for TMC26X and L6470 Stepper Drivers
 2015-03-11 15:31:57 -07:00
Mehmet Sutas
b373826428 Merge pull request #2 from MarlinFirmware/Development 
update
 2015-03-12 00:07:39 +02:00
alexborro
9157cbd8f3 Add Travel Acceleration and change the M204 options 
Added option to set Travel Acceleration (non printing moves).
The M204 options was a non sense (S for printing moves and T for retract
moves).

It has been changed to:
P = Printing moves
R = Retract only (no X, Y, Z) moves
T = Travel (non
printing) moves

I will add this info o G-Code wiki in reprap.org. I also advise to put
this info in Marlin next version changelog.
 2015-03-11 13:19:02 -03:00
alexborro
888cf161bd fix travel speed option for G29 
I forgot to enclousure the variable with #ifdef
 2015-03-11 10:03:32 -03:00
alexborro
af63b54562 Add travel speed option to G29 command line 2015-03-11 09:51:56 -03:00
alexborro
60ceca1bc1 Add speed configuration for home-bumping movement 2015-03-10 14:08:32 -03:00
domonoky
d813090d90 Merge remote-tracking branch 'remotes/upstream/Development' into Development 
Conflicts:
	Marlin/Marlin_main.cpp
	Marlin/stepper.cpp
 2015-03-10 10:46:37 +01:00
Scott Lahteine
c321c97f35 Merge pull request #1584 from galexander1/stringcleanup 
fix a handful of cases where strtod() was cast to int, instead of just using strtol()
 2015-03-10 01:48:30 -07:00
maverikou
53abc5e2f1 Merge branch 'Development' into delta_auto_bed_level 2015-03-09 22:28:57 +02:00
Mehmet Sutas
956fb2d278 Merge pull request #1 from MarlinFirmware/Development 
update
 2015-03-09 11:05:49 +02:00
Scott Lahteine
624f23f550 Merge pull request #1575 from Wurstnase/fix-controllerFan 
Fix controller fan
 2015-03-08 20:36:38 -07:00
maverikou
424c747fb3 Enable M401 and M402 for deltas with allen key z-probes. 2015-03-08 09:57:38 +02:00
maverikou
0d593ab7c1 Fix debug message 2015-03-08 09:41:31 +02:00
Greg Alexander
3e8c5678f5 fix bug where, i.e., "G1X1E1" would be interpretted as "G1 X10 E1", 
because strtod() will read the E address value as if it was a base 10
exponent.
 2015-03-07 21:14:34 -05:00
Greg Alexander
ed7874b4e0 M404 should not use 'N' address as parameter because 'N' is reserved for the line number 2015-03-07 17:35:06 -05:00
Greg Alexander
b9dfa5cad4 use code_value_long() instead of (int)code_value() 2015-03-07 17:33:15 -05:00
Greg Alexander
901b03d020 use strtol() instead of strtod() when an integer value is desired 2015-03-07 17:24:26 -05:00
Mehmet Sutas
cfc6a3a87a Filament Runout Sensor Feature 
With this change a mechanical or optical switch may be used to check the
availability of the filament and when the filament runs out an M600
(filament change) command is issued. This is only done while printing
with an SD card.

This feature was requested several times (issue #679), but the requests
were not accepted since it was believed that this situation should be
handled at host side. However during an SD print the control is totally
on firmware and I think that during an SD print it should be handled by
the firmware.

The original code was posted at reprap forum
(http://forums.reprap.org/read.php?1,297350) by Lazymonk. I have only
corrected some bugs of the code and improved it by adding definitions to
the configuration.h in order to make it more standardized.
 2015-03-07 22:43:15 +02:00
maverikou
7c24b97958 Ported over Johann Rocholl's improvements for delta printers: 
- Nonlinear auto bed leveling code (includes G29, G30, Z_RAISE_AFTER_PROBING). Cleaned it up to be a delta-specific AUTO_BED_LEVELING_GRID code path.
- Allen key z-probe deployment and retraction code. Cleaned it up and added safety checks.
 2015-03-07 20:36:21 +02:00
Wurstnase
a5342c942e Update Marlin_main.cpp 2015-03-07 16:47:53 +01:00
Scott Lahteine
d085725c86 More sanity-checking for ABL 
- Moved sanity-checks to Marlin_main.cpp
- Applied to other configuration files
- Fixed formatting of ABL output
- Passing verbose level to probe_pt
- Miscellaneous cleanup
- Put CONFIG_STEPPERS_TOSHIBA into Configuration.h
 2015-03-06 22:14:34 -08:00
Scott Lahteine
254970c92a Merge pull request #1570 from C-o-r-E/escape_fix 
Fixes gCode handling of comments and escaped characters
 2015-03-06 15:09:35 -08:00
Scott Lahteine
25dc79f124 Remove M48 credits also 2015-03-06 14:54:30 -08:00
Scott Lahteine
34e51f576f Fix compile error in gcode_G29 
- A redo of #1576, which missed topo_flag
- Always set verbose_level
 2015-03-06 14:52:05 -08:00
Wurstnase
62bd734612 fix controllerFan() for inverted enable pins 
add ```^ !(n_ENABLE_ON)``` for each stepper
 2015-03-06 12:01:17 +01:00
Gina Häußge
63b62d8d4e Fixed in-line comments and escaping 
* "G1 X1 ; test" was not executing "G1 X1" due to never leaving comment mode.
  * "M117 Hello \;)" printed "Hello \" to the display due to not replacing serial_char properly.

Tested with the following commands:
    * M117 Hello ; test => displays "Hello" on display, ignores "test"
    * G1 X1 ; foo => moves 1mm in X, ignores "foo"
    * ; test => completely ignored, not even acknowledged
    * M117 Hello \;) => displays "Hello ;)" on display
    * M117 Hello \\;) => displays "Hello \" on display, ignores ")"
 2015-03-05 23:30:34 +01:00
C-o-r-E
99fb1bc3e8 Attempt to resolve #1568 and add basic escape character support 2015-03-05 15:22:37 -05:00
Scott Lahteine
cdc38aa783 Move gcode handlers into inline functions 2015-03-05 04:27:24 -08:00
Scott Lahteine
6d9e9a6bef Merge branch 'Development' into enhanced_g29 
Latest upstream changes
 2015-03-05 02:49:18 -08:00
Scott Lahteine
4db2179f5c Include 4th extruder support 2015-03-05 02:37:36 -08:00
OhmEye
f90a947e65 Fix autoretract 
Autoretract was broken, looks like it was overlooked when the retracted flag was updated for multi extruders.
 2015-03-04 20:28:08 -10:00
Scott Lahteine
2ef6b3d57a Fix wrong defines, broken syntax 2015-03-04 22:24:44 -08:00
Scott Lahteine
32744d41a9 Do sanity checking on LRFB values 
- Setting boundaries based on configured limits, contrasting with G28
(which forgets these limits?)
 2015-03-04 21:32:11 -08:00
domonoky
075507fb9a missed one X_ENABLE_PIN 2015-03-03 11:09:56 +01:00
Scott Lahteine
dfb38874f8 Some suggested changes for #1555 2015-03-03 00:48:20 -08:00
Scott Lahteine
7f8ea7105f Arrange ProbeAction values bitwise 2015-03-02 20:14:37 -08:00
Scott Lahteine
7684721977 Enhanced G29 
- Adapted “Enhanced G29” code referred to in #1499 and posted at
[3dprintboard.com](http://3dprintboard.com/showthread.php?3105-Auto_Bed_
Leveling-Enhanced-G29-command)
- Compatible with current G29 while adding some new arguments
  - `V` sets the verbose level for serial out
  - `T` (or `V` > 2) send a Topology report to serial out
  - `E` works the same way as before
  - `P` works as before (source used `n` or `U`/`u`)
  - `L`, `R`, `B`, `F` work as before
- Still needs sanity checking for `LRBF`
 2015-03-02 20:00:17 -08:00
C-o-r-E
874d3d3fc5 Add support for solenoid articulated extruders 2015-03-02 20:07:12 -05:00
domonoky
4a7aca2736 Merge remote-tracking branch 'remotes/upstream/Development' into Development 2015-03-02 17:52:12 +01:00
Scott Lahteine
e30bfedce4 Fix undefined *_PROBE_BED_POSITION error 2015-03-01 19:57:35 -08:00
alexborro
227ab8c665 Merge pull request #1503 from MarcelMo/patch-2 
Support for simple customisable AutoZProbing area
 2015-02-25 13:22:42 -03:00
Scott Lahteine
c9a3eb0c1a Spacing in calculate_volumetric_multiplier(s) 2015-02-23 20:35:18 -08:00
Scott Lahteine
0cf0c20532 Optimize calculate_volumetric_multiplier 2015-02-23 18:10:35 -08:00
domonoky
b55995aae8 Introduce a layer of macro indirection to all stepper pins. This allows other stepper drivers to redefine them, so they can use SPI/I2C instead of direct pin manipulation. 2015-02-23 16:12:35 +01:00
Scott Lahteine
08c236059e Merge pull request #1505 from thinkyhead/issue_1499 
Bed leveling probe behavior issue?
 2015-02-19 01:24:17 -08:00
MagoKimbra
159196d1e9 Reset Alert message when finish M600 command 2015-02-18 21:33:38 +01:00
Scott Lahteine
978d114c73 Bed leveling probe behavior issue? 
The `float` keyword should not be on these vars because they conceal
the outer vars, preventing them from obtaining known values before
being passed in `set_bed_level_equation_3pts`. Possibly related to
`Z_RAISE_BETWEEN_PROBING` not functioning.
 2015-02-15 20:51:27 -08:00
MarcelMo
d28f5b9e82 Support for simple customisable AutoZProbing area 
When probing PCB´s I had the problem that i needed auto-leveling for specific areas (it´s never the same size).
Not much code, but very useful.
Now I use simply G29 L5 R55 F5 B35 P3 to probe a 4x6cm PCB before milling.
I used int for values... might be wrong...
I hope this time I got the right development tree. (tried first with https://github.com/MarlinFirmware/Marlin/pull/1130/commits)
 2015-02-15 15:58:29 +01:00
Scott Lahteine
7866fa161f Merge pull request #1476 from Natealus/Development 
Compiling errors with 4 Extruders defined and Viki 2 Implementation
 2015-02-12 16:56:55 -08:00
Jérémie FRANCOIS
9d75a56b56 Merge remote-tracking branch 'upstream/Development' into Development 
Conflicts:
	Marlin/Configuration.h
	Marlin/Marlin_main.cpp
 2015-02-11 06:38:36 +01:00
Natealus
38a500d05c Viki 2 Implementation 
I've insert the define and pointer entries for the Viki 2 and miniViki
from Panucatt in all of the example configs and main config. With these
additions and with pins done in the old single pin.h style...I was able
to get the display working fine save for needing to turn Delta Segments
per Second down. But that's a common graphics lcd issue being looked
into right now.

I need assistance in understanding how the new divided pins files fit
together because my previous attempts at trying to get it to work
appropriately didn't seem successful. This originally came from trying
to find out how to swap the XYZ Min and Max Endstop pins in the Azteeg
X3 Pro. It only comes with one set of connectors and they're Min
Endstops. My previous experience didn't turn out well trying to tell the
firmware to home to the Min Endstops so the best solution I found was to
swap the pins in the firmware. If I'm missing a conflict with a setup
other than delta please let me know, but it makes sense in my setup.
 2015-02-08 03:14:59 -07:00
Jérémie FRANCOIS
85e5aa4011 Generalized enqueue_commands_P, and moved them to Marlin_main as they should 2015-02-07 23:24:20 +01:00
Scott Lahteine
0cb1029311 remove extra plan_buffer_line 2015-02-03 11:26:36 -08:00
Scott Lahteine
b97a950f53 Apply fix for M600 filament change 
- Patch from #1453 for delta movement plan
- Fix: Set X with code X instead of adding to X
 2015-02-03 09:57:16 -08:00
Scott Lahteine
9dc5de6166 Hide code that makes veteran geeks go "aha!" 2015-02-02 05:55:55 -08:00
Scott Lahteine
bd387068bb Apply loops for extruders elsewhere also 2015-02-02 05:27:27 -08:00
Scott Lahteine
4a146d584b Loop, since the pending feature can use an array 2015-02-02 05:16:17 -08:00
Scott Lahteine
bca884bf72 Realized it's not a bug, but cleanup code anyway 2015-02-02 04:41:31 -08:00
Philip Schell
fb7c636ecf Avoid compiling error 
Only a missing ","... now it will compile again
 2015-02-01 01:33:04 +01:00
Scott Lahteine
073c59c50a Clean up some formatting 
- Also partial cleanup of Marlin_main.cpp with a smidgen of Doxygen.
 2015-01-29 18:52:21 -08:00
Scott Lahteine
093fedfde8 Make EEPROM storage consistent 
Update ConfigurationStore to always write dummy values for disabled
options, including FWRETRACT, DELTA, and SCARA. Update the EEPROM
version to “V15.” Also fixes a buffer overrun with axis_scaling in
Config_ResetDefault.
 2015-01-28 01:08:48 -08:00
Jérémie FRANCOIS
dd301be52d Added suport for multiline G-code commands in the LCD menus 2015-01-26 18:50:29 +01:00
AnHardt
59315330dd Remove definition of VERSION_STRING and replace where usend with STRING_VERSION 2015-01-26 15:52:01 +01:00
MagoKimbra
986e723eeb Add 4th extruder 2015-01-24 13:37:58 +01:00
daid
53f971095d Revert "Reduce PROGMEM warnings" 2015-01-16 16:48:22 +01:00
Bo Herrmannsen
5151db5c2f Merge pull request #1349 from msutas/patch-2 
Improvement - G29 Option for Not Retracting Servo
 2015-01-15 10:56:31 +01:00
Bo Herrmannsen
ab074dac17 Merge pull request #1344 from grob6000/independent_pid 
Independent PID parameters for each extruder
 2015-01-13 12:10:37 +01:00
Bo Herrmannsen
d4a665694a Merge pull request #1350 from odewdney/Development 
Reduce PROGMEM warnings
 2015-01-13 11:26:50 +01:00
msutas
3a5a6f42fb Corrected the ABL grid option 
G29 E was not retracting the probe on the last probe point when used with ABL grid. Corrected.
 2015-01-12 11:07:46 +02:00
odewdney
538859669d Removing compiler warnings for progmem 2015-01-11 18:14:21 +00:00
grob6000
bf2c923db5 Make multiple PID parameters a config option 
* Adds config parameter `PID_PARAMS_PER_EXTRUDER` - allows single PID
parameters to be used where this would be preferable (e.g. dual
identical extruders)
* When disabled, will use `float Kp, Ki, Kd, Kc;` as before.
Preprocessor macros used to switch between.
* ultralcd.cpp defines extra menus for extra parameters only where
required
* M301 reports `e:xx` only if independent pid parameters enabled
* EEPROM structure still leaves space for 3 extruders worth, when undef
will save single parameter to all extruder positions, but only read the
first
* Switching off saves approx 330 B with no LCD enabled, 2634B with LCD
(RRD) enabled: this is significant.
* LCD modifications should be tested.
 2015-01-11 13:50:17 +11:00
msutas
e0beb98fd3 Improvement - G29 Option for Not Retracting Servo 
This change introduces an improvement to G29 command on Marlin.

Auto bed leveling operation's reliability is based on the repeatability of the Z-probe switch and the servo. This change introduces an option to G29 command. When the G29 command is sent with an "e" option, during auto bed levelling the servo is not retracted between probes which decreases the bias on auto bed levelling resulting from servo.

G29 command does the auto bed probing as it is.

G29 E command engages the servo on first probing point, probes all points and retracts the servo after probing the last point.

Please comment your opinions, test on your printer and check the code on a programmer's perspective. (I am not a good programmer.)
 2015-01-10 17:25:39 +02:00
grob6000
37c7e8300f Independent PID parameters for each extruder 
* Variables Kp, Ki, Kd, Kc now arrays of size EXTRUDERS
* M301 gains (optional, default=0) E parameter to define which
extruder's settings to modify. Tested, works with Repetier Host's EEPROM
config window, albeit only reads/updates settings for E0.
* All Kp, Ki, Kd, Kc parameters saved in EEPROM (version now v14), up to
3 extruders supported (same as Marlin in general)
 2015-01-10 16:35:12 +11:00
Erik van der Zalm
1aade4a8e2 Merge branch 'Development' of https://github.com/MarlinFirmware/Marlin into Development 2015-01-09 21:33:29 +01:00
Erik van der Zalm
8a2e84e3f1 Possible fix for FWRETRACT with 0 zlift. 2015-01-09 21:33:02 +01:00
Erik van der Zalm
3a30d45c2e Revert "issue 968 for dev branch" 2015-01-07 23:40:17 +01:00
Dan Royer
9472bbe51d issue 968 for dev branch 
try, try again.

If 'OK' is garbled on sending PC won't receive it.  Both machines will
wait on each other forever.  This resends OK if nothing is heard from PC
for a while to avoid this bad case.
 2015-01-04 12:17:46 -08:00
Bo Herrmannsen
a18b625534 Merge pull request #1261 from wgm4321/Development 
Add Filament menu and add Filament/Retract settings to config store.
 2015-01-02 15:35:29 +01:00
bkubicek
d02daec08f fixed compilation 2014-12-30 08:04:06 +01:00
Bernhard Kubicek
f24c5d82e3 Update Marlin_main.cpp 
fixed minor typo
 2014-12-29 17:17:30 +01:00
Wurstnase
8a6f098cc6 Expand manage_inactivity #1264 
void manage_inactivity(bool ignore_stepper_queue=false)

standard is false so it is not necessary to change additional code. this
change should be better, hopefully nophead like this :)
 2014-12-29 17:07:22 +01:00
Wurstnase
d1995aec7a Rename ignore_blocks_queued 
more speaking name
 2014-12-29 16:47:08 +01:00
Wurstnase
4122de9d17 change filament issue 
make a more general solution
 2014-12-29 16:31:00 +01:00
wgm4321
cb12161191 Add Filament menu and add Filament/Retract settings to config store. 2014-12-28 20:43:14 -05:00
fmalpartida
ec33df0554 Merge branch 'SAV-MkI_merge' into Development 
Tested for SAV MKI and SAV 3D LCD on lewihe.
 2014-12-28 19:54:06 +01:00
alexborro
3afe66bb0c Fix issues #1248, #1240 
- Fixed issue when BAL area probing is shorter than it should be for
grid probing
- Warning when BAL activated with Delta Kinematics
- Fix XY_TRAVEL_SPEED when homing Z axis
 2014-12-28 13:27:39 -02:00
Lukas Obermann
9eb6df17a7 Consider negative Z Offsets when auto bed leveling is active 2014-12-28 12:46:35 +01:00
Denis Chertykov
050ca9ca13 Move initialization of errormagic[] and echomagic[] to Marlin_main.cpp 2014-12-28 09:09:42 +03:00
alexborro
d74aabf259 Revert "Change Auto_Bed_Leveling to Auto_Bed_Compensation" 2014-12-21 10:06:05 -02:00
Bo Herrmannsen
60628864ca Merge pull request #1167 from thinkyhead/sd_freemem 
Use SdFatUtil::FreeRam() for freeMemory() if there
 2014-12-20 18:31:21 +01:00
Bo Herrmannsen
889d7ba218 Merge pull request #1177 from martin-pr/probing_z_speed 
Split do_blocking_move() to XY and Z sections
 2014-12-20 18:30:35 +01:00
Bo Herrmannsen
5e7bd2dc87 Merge pull request #1200 from chertykov/Marlin_v1 
Fix syntax errors in #ifdef
 2014-12-20 18:29:39 +01:00
Denis Chertykov
b086394178 Fix syntax errors in #ifdef. 2014-12-20 19:33:43 +03:00
John Davis
4315c2547a Update Marlin_main.cpp 
Changed level and leveling to compensation (except with "verbose_level" and "lcd_reset_alert_level").
 2014-12-19 17:41:29 -05:00
Bo Herrmannsen
03e489aaad Merge pull request #1197 from foosel/fix/issue_1147 
Fixes commands not being acknowledged in the same order they are received in
 2014-12-19 14:39:05 +01:00
Gina Häußge
acc0e75279 Fixes commands not being acknowledged in the same order they are received 
in

G0 to G3 were previously acknowledged in the get_command method, causing
them to be possibly acknowledged before commands coming after them that
were acknowledged in process_commands.

This patch fixes this, moving the acknowledgement of G0 to G3 to the
process_commands method as well. These commands are therefore no
longer acknowledged when the enter the cmd_buffer but instead only
acknowledged when the enter the plan_buffer.

Guaranteeing that commands are acknowledged in the same order in which
they were received by the firmware allows host software to be able to
track the life cycle of commands and such a better management of the
firmware's serial buffers as well as better internal command processing
and response parsing without having to depend on throwing an epic
amount of regular expressions against each line received back from the
firmware.

Fixes ErikZalm/Marlin#1147
 2014-12-19 14:20:36 +01:00
Scott Lahteine
07c6b5ab71 Using axis constants 2014-12-18 08:13:08 -08:00
Scott Lahteine
0450e83fa5 Use SdFatUtil::FreeRam() for freeMemory() if there 2014-12-17 23:26:52 -08:00
Scott Lahteine
60598b4cdd A few constants where they belong 2014-12-17 23:01:24 -08:00
Martin Prazak
2ef0669b19 Split do_blocking_move() to XY and Z sections to make sure that the Z homing feedrate is not exceeded 2014-12-07 15:31:46 +00:00
Neil Darlow
64139f5e5a Merge https://github.com/ErikZalm/Marlin into Marlin_v1 2014-12-04 21:09:03 +00:00
Scott Lahteine
7562183efc Skip over spaces first 2014-11-28 08:09:28 -08:00
Scott Lahteine
12b51d6060 Ignore S and P if no value >0 is included. 2014-11-26 21:05:11 -08:00
Scott Lahteine
d12b24758a Clear LCD to welcome_msg if not printing 
The welcome message is more appropriate than “resuming print” if
nothing is printing.
 2014-11-26 21:05:11 -08:00
Scott Lahteine
92e21d3ee2 M0-M1 Enhancements 
Allow M0 and M1 to include a message string. Ignore clicks on “Wait for
user” so that the Info Screen stays up.
 2014-11-26 21:05:10 -08:00
Neil Darlow
b81021f475 Merge https://github.com/ErikZalm/Marlin into Marlin_v1 2014-10-21 12:06:56 +01:00
Erik van der Zalm
058e446531 Merge pull request #1037 from filipmu/Filament-Sensor 
Support for a filament diameter sensor
 2014-10-11 22:56:01 +02:00
Erik van der Zalm
b360306881 Merge pull request #1073 from WingTangWong/wing-fix-float-delta 
Wing fix float delta
 2014-10-06 13:41:01 +02:00
Scott Lahteine
f989bd5435 Simple code cleanup. Rename "homeing" to homing. 2014-10-05 13:20:53 -07:00
Neil Darlow
6c5a460e65 Merge branch 'Marlin_v1' of https://github.com/ErikZalm/Marlin into Marlin_v1 2014-10-05 12:54:54 +01:00
galexander1
cb4a6dd2dc Merge pull request #1065 from oliasmage/Marlin_v1 
Corrected retract() call for use of auto probe without sled enabled.
 2014-09-19 15:12:09 -04:00
Bracken Dawson
01e9b536cb Fix build for non-sled bed auto levelling 
This function should only be used with sled, not all bed auto
levelling.
 2014-09-19 19:42:32 +01:00
Wing Tang Wong
58eabd21fb Added ifndef 2014-09-16 14:31:58 -07:00
Wing Tang Wong
88d12a762a Added #ifndef DELTA wrapper to float delta 2014-09-16 14:29:44 -07:00
Charles Bell
3b8216bdd1 Corrected #endif and ifdef for Z_PROBE_SLED code. 2014-09-04 16:40:22 -04:00
Charles Bell
37799f70ba Corrected retract() call for use of auto probe without sled enabled. 2014-09-04 14:36:39 -04:00
Neil Darlow
1632e5e38a Merge branch 'Marlin_v1' of https://github.com/ErikZalm/Marlin into Marlin_v1 2014-09-04 12:21:35 +01:00
Erik van der Zalm
018b68a5c4 Merge pull request #976 from cocktailyogi/SCARA_by_Yogi 
Implemented SCARA-Maths
 2014-08-28 16:32:52 +02:00
Erik van der Zalm
9887555192 Merge pull request #998 from darconeous/pull-requests/fwretract 
FWRETRACT fixes
 2014-08-28 16:24:51 +02:00
Erik van der Zalm
68dd5e635e Merge pull request #1024 from oliasmage/Marlin_v1 
Adding Z Probe via sled mounted endstop
 2014-08-28 16:15:54 +02:00
Erik van der Zalm
25069ed4e9 Merge pull request #1031 from Roxy-3DPrintBoard/Z_PROBE_REPEATABILITY-with-correct-Defaults 
Z probe repeatability with correct defaults
 2014-08-28 16:14:10 +02:00
Filip Mulier
62db9848d3 Improvements and bug fixes in sensor delay buffer for filament sensor code 
Improvement to avoid reinitializing delay buffer with every print. Fixed
issues in buffer indexing and memory out of bounds due to floating point
imprecision.  Simplified the code by avoiding conversion to standard
diameter and 1cu mm extrusion, which caused complications in determining
mm extruded.
 2014-08-16 06:50:13 -05:00
Florian Baumann
5908fd5cec Fix reseting CHDK pin to LOW 
chdkActive was set to false regardless of (millis() - chdkHigh) being bigger than the CHDK_DELAY or not. So if (millis() - chdkHigh) wasn't bigger than the delay the first time, the CHDK would never be set back to LOW.

Also, don't return from the function, as there might be other stuff to do, after the CHDK check.
 2014-08-11 14:12:32 +02:00
Roxy-3DPrintBoard
0091865583 Z_PROBE_REPEATABILITY test 
Z_PROBE_REPEATABILITY test for Auto Bed Leveling.
Implemented as M48 with extra user specified options.
Full support at
http://3dprintboard.com/showthread.php?2802-Auto_Bed_Leveling-Z-Probe-Repeatability-code
 2014-08-09 15:37:23 -05:00
Filip Mulier
85649a4549 Real-time filament diameter measurement and control 
This feature allows the printer to read the filament diameter
automatically and adjust the printer in real time.  Added code to read
an analog voltage that represents a filament diameter measurement.  This
measurement is delayed in a ring buffer to compensate for sensors that
are a distance away from the extruder.  The measurement is used to
adjust the volumetric_multiplier for the extruder.  Some additional g
codes (M404, M405, M406, M407) are used to set parameters and turn
on/off the control. g code M221 is updated.  Pins for RAMPS1.4, RAMBO,
and Printrboard are identified for analog input.  The configuration file
is updated with relevant user parameters.
 2014-08-06 19:30:57 -05:00
Charles Bell
d2fcb3ee56 CAB: Added code for Z-probe with Z endstop mounted on a sled. 2014-08-01 11:29:59 -04:00
Neil Darlow
3cd7dbcc45 Merge branch 'Marlin_v1' of https://github.com/ErikZalm/Marlin into Marlin_v1 2014-07-30 13:01:52 +01:00
daid
c13a831ea1 Merge pull request #1017 from foosel/fix/checksum_truncation_bug 
Fix for a wrong checksum truncation for certain commands
 2014-07-24 19:41:34 +02:00
Gina Häußge
2d22902d08 Fix for a wrong checksum truncation for certain commands 
Positioning of string terminator to truncate checksum from the commands
M23, M28, M30, M32, M928 and M117 was off by one, causing the last
letter of the actual command to be truncated instead of just the
checksum.

In case of the SD commands this caused checksummed commands targeting
existing files to fail since the last letter of the filename was
truncated.

In case of M117 this caused the last given letter not to be displayed.

This patch fixes the off-by-one error and sets the null terminator
on the exact position of the * starting the checksum instead of the
character before that.
 2014-07-24 12:04:02 +02:00
cocktailyogi
2f4a20257c imported last Marlin changes 2014-07-20 13:49:26 +02:00
daid
aacff0d361 Merge pull request #948 from Dim3nsioneer/Marlin_v1 
Implementation of FW extruder change retract
 2014-07-18 16:10:15 +02:00
Robert Quattlebaum
1fd9a7d476 Fix for FWRETRACT on DELTA printers. 
Fixes #817
 2014-07-09 09:24:26 -07:00
Neil Darlow
3f2c771d90 Merge branch 'Marlin_v1' of https://github.com/ErikZalm/Marlin into Marlin_v1 2014-07-07 18:17:15 +01:00
Pablo Clemente
2242a84218 Changed the declaration of the variable to Marlin_main.cpp to fix issue on commit #965 2014-07-01 16:45:03 +02:00
Neil Darlow
6e3406d228 Merge branch 'Marlin_v1' of https://github.com/ErikZalm/Marlin into Marlin_v1 2014-07-01 10:27:39 +01:00
Pablo Clemente
d86c3cf43c Changed the type of variable to bool, the name to "cancel_heatup", flags implementation and added this fix to M190 gcode too. 2014-06-30 15:12:13 +02:00
cocktailyogi
f0cab611db optimised some math-code 2014-06-24 18:43:36 +02:00
cocktailyogi
fae7d08698 fixed wrong compiler-option 2014-06-23 18:16:42 +02:00
cocktailyogi
512f2a3136 restore Branch from Backup 
sorry for that
 2014-06-23 17:09:57 +02:00
Pablo Clemente
cd3220d055 Inverted state logic for forced_heating_stop variable 2014-06-13 08:39:58 +02:00
Pablo Clemente
86b4b805d2 Fixed stop print LCD function on M104 2014-06-12 18:43:16 +02:00
Dim3nsioneer
3c927901a4 Implementation of FW extruder change retract 
FW retraction is extended onto swap retraction invoked by 'G10 S1'.
Bookkeeping of the retract state of all extruders allows for having one
extruder fw standard retracted while another extruder is swap retracted.
An LCD menu item for the swap retract and recover length was added.
 2014-06-02 17:02:10 +02:00
neildarlow
efb6d61413 Merge branch 'Marlin_v1' of https://github.com/ErikZalm/Marlin into Marlin_v1 2014-05-24 13:08:58 +01:00
nothinman
38192cb5f3 Add M112 description to Marlin_main 2014-05-20 15:20:19 +01:00
nothinman
aed5ec008a Merge pull request #851 from DanNixon/estop 
Implemented M112
 2014-05-19 17:55:34 +01:00
Erik van der Zalm
cfb98ef682 More coverity fixes 2014-05-15 22:09:50 +02:00
Erik van der Zalm
9db9842aea Fixed error found by the free coverity tool (https://scan.coverity.com/) 
===================================================
Hi,

Please find the latest report on new defect(s) introduced to ErikZalm/Marlin found with Coverity Scan.

Defect(s) Reported-by: Coverity Scan
Showing 15 of 15 defect(s)

** CID 59629:  Unchecked return value  (CHECKED_RETURN)
/Marlin_main.cpp: 2154 in process_commands()()

** CID 59630:  Operands don't affect result  (CONSTANT_EXPRESSION_RESULT)
/Applications/Arduino.app/Contents/Resources/Java/hardware/arduino/cores/arduino/Tone.cpp: 319 in tone(unsigned char, unsigned int, unsigned long)()

** CID 59631:  Missing break in switch  (MISSING_BREAK)
/Marlin_main.cpp: 1187 in process_commands()()

** CID 59632:  Missing break in switch  (MISSING_BREAK)
/Marlin_main.cpp: 1193 in process_commands()()

** CID 59633:  Out-of-bounds write  (OVERRUN)
/temperature.cpp: 914 in disable_heater()()

** CID 59634:  Out-of-bounds write  (OVERRUN)
/temperature.cpp: 913 in disable_heater()()

** CID 59635:  Out-of-bounds read  (OVERRUN)
/temperature.cpp: 626 in analog2temp(int, unsigned char)()

** CID 59636:  Out-of-bounds read  (OVERRUN)
/temperature.cpp: 620 in analog2temp(int, unsigned char)()

** CID 59637:  Out-of-bounds write  (OVERRUN)
/temperature.cpp: 202 in PID_autotune(float, int, int)()

** CID 59638:  Out-of-bounds read  (OVERRUN)
/temperature.cpp: 214 in PID_autotune(float, int, int)()

** CID 59639:  Out-of-bounds write  (OVERRUN)
/Marlin_main.cpp: 2278 in process_commands()()

** CID 59640:  Out-of-bounds read  (OVERRUN)
/Marlin_main.cpp: 1802 in process_commands()()

** CID 59641:  Uninitialized scalar field  (UNINIT_CTOR)
/Applications/Arduino.app/Contents/Resources/Java/libraries/LiquidCrystal/LiquidCrystal.cpp: 51 in LiquidCrystal::LiquidCrystal(unsigned char, unsigned char, unsigned char, unsigned char, unsigned char, unsigned char)()

** CID 59642:  Uninitialized scalar field  (UNINIT_CTOR)
/Applications/Arduino.app/Contents/Resources/Java/libraries/LiquidCrystal/LiquidCrystal.cpp: 45 in LiquidCrystal::LiquidCrystal(unsigned char, unsigned char, unsigned char, unsigned char, unsigned char, unsigned char, unsigned char)()

** CID 59643:  Uninitialized scalar field  (UNINIT_CTOR)
/Applications/Arduino.app/Contents/Resources/Java/libraries/LiquidCrystal/LiquidCrystal.cpp: 32 in LiquidCrystal::LiquidCrystal(unsigned char, unsigned char, unsigned char, unsigned char, unsigned char, unsigned char, unsigned char, unsigned char, unsigned char, unsigned char, unsigned char)()

________________________________________________________________________________________________________
*** CID 59629:  Unchecked return value  (CHECKED_RETURN)
/Marlin_main.cpp: 2154 in process_commands()()
2148                 }
2149               #endif
2150             }
2151           }
2152           break;
2153         case 85: // M85
   CID 59629:  Unchecked return value  (CHECKED_RETURN)
   Calling "code_seen" without checking return value (as is done elsewhere 66 out of 67 times).
2154           code_seen('S');
2155           max_inactive_time = code_value() * 1000;
2156           break;
2157         case 92: // M92
2158           for(int8_t i=0; i < NUM_AXIS; i++)
2159           {

________________________________________________________________________________________________________
*** CID 59630:  Operands don't affect result  (CONSTANT_EXPRESSION_RESULT)
/Applications/Arduino.app/Contents/Resources/Java/hardware/arduino/cores/arduino/Tone.cpp: 319 in tone(unsigned char, unsigned int, unsigned long)()
313         else
314         {
315           // two choices for the 16 bit timers: ck/1 or ck/64
316           ocr = F_CPU / frequency / 2 - 1;
317
318           prescalarbits = 0b001;
   CID 59630:  Operands don't affect result  (CONSTANT_EXPRESSION_RESULT)
   "ocr > 65535U" is always false regardless of the values of its operands. This occurs as the logical operand of if.
319           if (ocr > 0xffff)
320           {
321             ocr = F_CPU / frequency / 2 / 64 - 1;
322             prescalarbits = 0b011;
323           }
324

________________________________________________________________________________________________________
*** CID 59631:  Missing break in switch  (MISSING_BREAK)
/Marlin_main.cpp: 1187 in process_commands()()
1181         case 2: // G2  - CW ARC
1182           if(Stopped == false) {
1183             get_arc_coordinates();
1184             prepare_arc_move(true);
1185             return;
1186           }
   CID 59631:  Missing break in switch  (MISSING_BREAK)
   The above case falls through to this one.
1187         case 3: // G3  - CCW ARC
1188           if(Stopped == false) {
1189             get_arc_coordinates();
1190             prepare_arc_move(false);
1191             return;
1192           }

________________________________________________________________________________________________________
*** CID 59632:  Missing break in switch  (MISSING_BREAK)
/Marlin_main.cpp: 1193 in process_commands()()
1187         case 3: // G3  - CCW ARC
1188           if(Stopped == false) {
1189             get_arc_coordinates();
1190             prepare_arc_move(false);
1191             return;
1192           }
   CID 59632:  Missing break in switch  (MISSING_BREAK)
   The above case falls through to this one.
1193         case 4: // G4 dwell
1194           LCD_MESSAGEPGM(MSG_DWELL);
1195           codenum = 0;
1196           if(code_seen('P')) codenum = code_value(); // milliseconds to wait
1197           if(code_seen('S')) codenum = code_value() * 1000; // seconds to wait
1198

________________________________________________________________________________________________________
*** CID 59633:  Out-of-bounds write  (OVERRUN)
/temperature.cpp: 914 in disable_heater()()
908          WRITE(HEATER_0_PIN,LOW);
909        #endif
910       #endif
911
912       #if defined(TEMP_1_PIN) && TEMP_1_PIN > -1
913         target_temperature[1]=0;
   CID 59633:  Out-of-bounds write  (OVERRUN)
   Overrunning array "soft_pwm" of 1 bytes at byte offset 1 using index "1".
914         soft_pwm[1]=0;
915         #if defined(HEATER_1_PIN) && HEATER_1_PIN > -1
916           WRITE(HEATER_1_PIN,LOW);
917         #endif
918       #endif
919

________________________________________________________________________________________________________
*** CID 59634:  Out-of-bounds write  (OVERRUN)
/temperature.cpp: 913 in disable_heater()()
907        #if defined(HEATER_0_PIN) && HEATER_0_PIN > -1
908          WRITE(HEATER_0_PIN,LOW);
909        #endif
910       #endif
911
912       #if defined(TEMP_1_PIN) && TEMP_1_PIN > -1
   CID 59634:  Out-of-bounds write  (OVERRUN)
   Overrunning array "target_temperature" of 1 2-byte elements at element index 1 (byte offset 2) using index "1".
913         target_temperature[1]=0;
914         soft_pwm[1]=0;
915         #if defined(HEATER_1_PIN) && HEATER_1_PIN > -1
916           WRITE(HEATER_1_PIN,LOW);
917         #endif
918       #endif

________________________________________________________________________________________________________
*** CID 59635:  Out-of-bounds read  (OVERRUN)
/temperature.cpp: 626 in analog2temp(int, unsigned char)()
620       if(heater_ttbl_map[e] != NULL)
621       {
622         float celsius = 0;
623         uint8_t i;
624         short (*tt)[][2] = (short (*)[][2])(heater_ttbl_map[e]);
625
   CID 59635:  Out-of-bounds read  (OVERRUN)
   Overrunning array "heater_ttbllen_map" of 1 bytes at byte offset 1 using index "e" (which evaluates to 1).
626         for (i=1; i<heater_ttbllen_map[e]; i++)
627         {
628           if (PGM_RD_W((*tt)[i][0]) > raw)
629           {
630             celsius = PGM_RD_W((*tt)[i-1][1]) +
631               (raw - PGM_RD_W((*tt)[i-1][0])) *

________________________________________________________________________________________________________
*** CID 59636:  Out-of-bounds read  (OVERRUN)
/temperature.cpp: 620 in analog2temp(int, unsigned char)()
614         if (e == 0)
615         {
616           return 0.25 * raw;
617         }
618       #endif
619
   CID 59636:  Out-of-bounds read  (OVERRUN)
   Overrunning array "heater_ttbl_map" of 1 2-byte elements at element index 1 (byte offset 2) using index "e" (which evaluates to 1).
620       if(heater_ttbl_map[e] != NULL)
621       {
622         float celsius = 0;
623         uint8_t i;
624         short (*tt)[][2] = (short (*)[][2])(heater_ttbl_map[e]);
625

________________________________________________________________________________________________________
*** CID 59637:  Out-of-bounds write  (OVERRUN)
/temperature.cpp: 202 in PID_autotune(float, int, int)()
196       {
197          soft_pwm_bed = (MAX_BED_POWER)/2;
198          bias = d = (MAX_BED_POWER)/2;
199        }
200        else
201        {
   CID 59637:  Out-of-bounds write  (OVERRUN)
   Overrunning array "soft_pwm" of 1 bytes at byte offset 1 using index "extruder" (which evaluates to 1).
202          soft_pwm[extruder] = (PID_MAX)/2;
203          bias = d = (PID_MAX)/2;
204       }
205
206
207

________________________________________________________________________________________________________
*** CID 59638:  Out-of-bounds read  (OVERRUN)
/temperature.cpp: 214 in PID_autotune(float, int, int)()
208
209      for(;;) {
210
211         if(temp_meas_ready == true) { // temp sample ready
212           updateTemperaturesFromRawValues();
213
   CID 59638:  Out-of-bounds read  (OVERRUN)
   Overrunning array "current_temperature" of 1 4-byte elements at element index 1 (byte offset 4) using index "extruder" (which evaluates to 1).
214           input = (extruder<0)?current_temperature_bed:current_temperature[extruder];
215
216           max=max(max,input);
217           min=min(min,input);
218           if(heating == true && input > temp) {
219             if(millis() - t2 > 5000) {

________________________________________________________________________________________________________
*** CID 59639:  Out-of-bounds write  (OVERRUN)
/Marlin_main.cpp: 2278 in process_commands()()
2272               tmp_extruder = code_value();
2273               if(tmp_extruder >= EXTRUDERS) {
2274                 SERIAL_ECHO_START;
2275                 SERIAL_ECHO(MSG_M200_INVALID_EXTRUDER);
2276               }
2277             }
   CID 59639:  Out-of-bounds write  (OVERRUN)
   Overrunning array "volumetric_multiplier" of 1 4-byte elements at element index 1 (byte offset 4) using index "tmp_extruder" (which evaluates to 1).
2278             volumetric_multiplier[tmp_extruder] = 1 / area;
2279           }
2280           break;
2281         case 201: // M201
2282           for(int8_t i=0; i < NUM_AXIS; i++)
2283           {

________________________________________________________________________________________________________
*** CID 59640:  Out-of-bounds read  (OVERRUN)
/Marlin_main.cpp: 1802 in process_commands()()
1796             int pin_status = code_value();
1797             int pin_number = LED_PIN;
1798             if (code_seen('P') && pin_status >= 0 && pin_status <= 255)
1799               pin_number = code_value();
1800             for(int8_t i = 0; i < (int8_t)sizeof(sensitive_pins); i++)
1801             {
   CID 59640:  Out-of-bounds read  (OVERRUN)
   Overrunning array "sensitive_pins" of 28 2-byte elements at element index 55 (byte offset 110) using index "i" (which evaluates to 55).
1802               if (sensitive_pins[i] == pin_number)
1803               {
1804                 pin_number = -1;
1805                 break;
1806               }
1807             }

________________________________________________________________________________________________________
*** CID 59641:  Uninitialized scalar field  (UNINIT_CTOR)
/Applications/Arduino.app/Contents/Resources/Java/libraries/LiquidCrystal/LiquidCrystal.cpp: 51 in LiquidCrystal::LiquidCrystal(unsigned char, unsigned char, unsigned char, unsigned char, unsigned char, unsigned char)()
45     }
46
47     LiquidCrystal::LiquidCrystal(uint8_t rs,  uint8_t enable,
48     			     uint8_t d0, uint8_t d1, uint8_t d2, uint8_t d3)
49     {
50       init(1, rs, 255, enable, d0, d1, d2, d3, 0, 0, 0, 0);
   CID 59641:  Uninitialized scalar field  (UNINIT_CTOR)
   Non-static class member "_initialized" is not initialized in this constructor nor in any functions that it calls.
51     }
52
53     void LiquidCrystal::init(uint8_t fourbitmode, uint8_t rs, uint8_t rw, uint8_t enable,
54     			 uint8_t d0, uint8_t d1, uint8_t d2, uint8_t d3,
55     			 uint8_t d4, uint8_t d5, uint8_t d6, uint8_t d7)
56     {

________________________________________________________________________________________________________
*** CID 59642:  Uninitialized scalar field  (UNINIT_CTOR)
/Applications/Arduino.app/Contents/Resources/Java/libraries/LiquidCrystal/LiquidCrystal.cpp: 45 in LiquidCrystal::LiquidCrystal(unsigned char, unsigned char, unsigned char, unsigned char, unsigned char, unsigned char, unsigned char)()
39     }
40
41     LiquidCrystal::LiquidCrystal(uint8_t rs, uint8_t rw, uint8_t enable,
42     			     uint8_t d0, uint8_t d1, uint8_t d2, uint8_t d3)
43     {
44       init(1, rs, rw, enable, d0, d1, d2, d3, 0, 0, 0, 0);
   CID 59642:  Uninitialized scalar field  (UNINIT_CTOR)
   Non-static class member "_initialized" is not initialized in this constructor nor in any functions that it calls.
45     }
46
47     LiquidCrystal::LiquidCrystal(uint8_t rs,  uint8_t enable,
48     			     uint8_t d0, uint8_t d1, uint8_t d2, uint8_t d3)
49     {
50       init(1, rs, 255, enable, d0, d1, d2, d3, 0, 0, 0, 0);

________________________________________________________________________________________________________
*** CID 59643:  Uninitialized scalar field  (UNINIT_CTOR)
/Applications/Arduino.app/Contents/Resources/Java/libraries/LiquidCrystal/LiquidCrystal.cpp: 32 in LiquidCrystal::LiquidCrystal(unsigned char, unsigned char, unsigned char, unsigned char, unsigned char, unsigned char, unsigned char, unsigned char, unsigned char, unsigned char, unsigned char)()
26
27     LiquidCrystal::LiquidCrystal(uint8_t rs, uint8_t rw, uint8_t enable,
28     			     uint8_t d0, uint8_t d1, uint8_t d2, uint8_t d3,
29     			     uint8_t d4, uint8_t d5, uint8_t d6, uint8_t d7)
30     {
31       init(0, rs, rw, enable, d0, d1, d2, d3, d4, d5, d6, d7);
   CID 59643:  Uninitialized scalar field  (UNINIT_CTOR)
   Non-static class member "_initialized" is not initialized in this constructor nor in any functions that it calls.
32     }
33
34     LiquidCrystal::LiquidCrystal(uint8_t rs, uint8_t enable,
35     			     uint8_t d0, uint8_t d1, uint8_t d2, uint8_t d3,
36     			     uint8_t d4, uint8_t d5, uint8_t d6, uint8_t d7)
37     {

________________________________________________________________________________________________________
To view the defects in Coverity Scan visit, http://scan.coverity.com/projects/2224?tab=overview
 2014-05-14 21:59:48 +02:00
Neil Darlow
e541323741 Merge https://github.com/ErikZalm/Marlin into Marlin_v1 2014-05-09 15:02:50 +01:00
MyMakibox
21ec6b88c3 Update Marlin_main.cpp 
Added description of autotemp flags to M109
 2014-04-23 17:33:26 +08:00
Neil Darlow
6adbdf42e0 Merge branch 'Marlin_v1' of https://github.com/ErikZalm/Marlin into Marlin_v1 2014-04-21 15:10:57 +01:00
whosawhatsis
27d544ac25 Speed up QUICK_HOME feedrate for diagonal move 
Speed up the diagonal move while still keeping each individual axis at
or below its homing feedrate.
 2014-04-19 17:29:20 -07:00
neildarlow
95ad6ec9a1 Merge branch 'Marlin_v1' of https://github.com/ErikZalm/Marlin into Marlin_v1 2014-04-12 22:20:45 +01:00
Gabe Rosenhouse
27a7cf9fcf use existing strings 2014-04-07 05:01:48 -05:00
Gabe Rosenhouse
b0aeac117f Adjustable Z probe offset, via custom M-code 2014-04-06 19:45:56 -05:00
Neil Darlow
73b380d8d2 Merge branch 'Marlin_v1' of https://github.com/ErikZalm/Marlin into Marlin_v1 2014-04-06 19:15:29 +01:00
nothinman
c23376f2e7 Merge pull request #837 from whosawhatsis/fwretract 
FWRETRACT in mm/s
 2014-04-04 11:47:58 +01:00
nothinman
9a5d23d96f Merge pull request #866 from sakunamary/Marlin_v1 
fix bug for dual extruders not working
 2014-04-02 18:27:42 +01:00
nothinman
303ee67896 Merge pull request #864 from whosawhatsis/M200 
fix bug in M200 with multiple extruders
 2014-04-02 18:26:15 +01:00
Tim
8759508319 fix bug for dual extruders not working 
some guy find that marlin not working good for dual extruders delta .
when type T0 or T1 to active extruder and  E0 or E1  move causing XYZ
motion . so i locales the bugs and fix it , I have dry run the fix.
 2014-04-01 09:26:19 +08:00
whosawhatsis
a65564eef6 fix bug in M200 with multiple extruders 2014-03-30 11:42:22 -07:00
whosawhatsis
aeaf9b9312 fix bug in M200 with multiple extruders 2014-03-30 11:41:57 -07:00
Dan Nixon
f643f4d674 Test and refactor 2014-03-21 20:42:00 +00:00
neildarlow
bbe8fbe13d Merge branch 'Marlin_v1' of https://github.com/ErikZalm/Marlin into Marlin_v1 2014-03-21 18:27:14 +00:00
Dim3nsioneer
3906f27c46 Individual extruder flow rate 
Extension of M221, Tune menu
 2014-03-15 18:09:46 +01:00
Dan Nixon
a38c90ee84 Added estop handling 2014-03-15 15:56:15 +00:00
Dan Nixon
272072fa20 Added M112 2014-03-14 23:19:43 +00:00
whosawhatsis
aab61e63c3 FWRETRACT in mm/s 
Firmware retraction now stores the retract and recover speeds in mm/s
instead of mm/min. This makes it match the units of the maximum
feedrate, and fixes problems with modifying the value via LCD control
panel. From gcode, the values are still taken in mm/min to match the
units of G1 and similar, and they are converted to mm/s before they are
stored.

I also lowered the default retract feedrate to make it less likely to
cause problems for geared extruders when the user hasn’t bothered to
set a reasonable maximum feedrate, though users should be setting both
of these values to suit their hardware.
 2014-03-14 15:17:28 -07:00
blddk
09af1b90b8 Added CHDK support 
Added CHDK support to take pictures instead of doing an IR command, see more about how to use it here http://captain-slow.dk/2014/03/09/3d-printing-timelapses/
 2014-03-10 21:57:08 +01:00
neildarlow
7325d7102e Activate LiquidTWI2 device detection and space-pad LCD status line. 2014-03-03 21:01:27 +00:00
Jim Morris
8ea5665ee2 Merge remote-tracking branch 'origin/Marlin_v1' into add/M665-set-delta-configuration 
Conflicts:
	Marlin/Marlin_main.cpp
 2014-02-26 00:19:28 -08:00
Cylindric
fdce91192e Various typo fixes - only in comments, no code changes. 2014-02-25 10:01:15 +00:00
whosawhatsis
77df0d689a autretract fix 
I made these changes previously, but I can’t find the commit now. This
reapplies the changes to get auto retract working again.

Conflicts:
	Marlin/Configuration_adv.h
	Marlin/Marlin_main.cpp
 2014-02-24 13:24:38 -08:00
Gabe Rosenhouse
174b8d99d5 Simplify 3-point probing using new code only 2014-02-19 21:48:05 -08:00
Gabe Rosenhouse
3b718b816c better documentation 2014-02-19 14:04:37 -08:00
Gabe Rosenhouse
34fd59c370 ABL at any points 2014-02-19 13:18:21 -08:00
alexborro
9fa328e5c8 Merge pull request #793 from MissionSt/use_axis_enums 
Use constants instead of numeric literals
 2014-02-19 10:15:57 -03:00
Gabe Rosenhouse
f308a8af91 update comment 2014-02-19 01:06:24 -08:00
Gabe Rosenhouse
357e31270a Prevent G29 without first homing in X and Y 
If position is unknown, then G29 can be dangerous.
 2014-02-19 00:51:43 -08:00
Gabe Rosenhouse
d2d7d186b5 Use descriptive constants, more 2014-02-19 00:10:17 -08:00
Gabe Rosenhouse
2ccdf4f36d Use descriptive constants instead of numeric literals 2014-02-19 00:02:59 -08:00
daid
46bae30573 Merge pull request #776 from whosawhatsis/fwretract 
Fwretract fixes, cleanup
 2014-02-18 10:39:28 +01:00
Jim Morris
af9395ac2e Add M605 to dynamically set delta configuration 
Save above configs in eeprom
fix docs in createTemperatureLookupMarlin.py
add missing azteegX3pro digipot settings in delta example config
 2014-02-17 20:50:59 -08:00
nothinman
fd42f0d226 Merge pull request #783 from MissionSt/fix/syntax-error 
Fix compile error
 2014-02-17 20:59:43 +00:00
nothinman
96217bf36a Merge pull request #777 from PxT/M114 
Add whitespace to M114 output
 2014-02-17 18:07:47 +00:00
Gabe Rosenhouse
d1c64b9dc4 Fix syntax error introduced in 477b6fa1d 2014-02-17 07:56:19 -08:00
nothinman
d4ba23bc28 Merge pull request #770 from josefpavlik/Marlin_v1 
Marlin v1
 2014-02-17 11:27:05 +00:00
Paul Telford
306588925d Add whitespace to M114 output 2014-02-16 21:01:19 -08:00
whosawhatsis
c43838bb1e disable auto retract by default 
This should make it safe to enable FWRETRACT by default, with
autoretract (which should now be fixed) only enabled by M209. FWRETRACT
should probably now default to enabled (to make G10/G11 and M207-209
available, without changing functionality when they are not used), but
I’ll save that for another pull request/discussion.
 2014-02-16 19:04:54 -08:00
whosawhatsis
99f0e44864 Move FWRETRACT defaults to configuration_adv.h 2014-02-16 19:00:28 -08:00
whosawhatsis
66e3869138 Fix autoretract 
This takes the (now working) G10/G11 code and moves it to a function,
which is called by G10 and G11, and also called by G1 if autoretract is
enabled and a retract/recover move is detected.
 2014-02-16 18:59:04 -08:00
whosawhatsis
2f2459c0db Fix G10/G11 Z-lift 2014-02-16 18:15:34 -08:00
Gabe Rosenhouse
8c5675c290 Use language.h instead of English literals for "bed" 2014-02-16 17:16:00 -08:00
Gabe Rosenhouse
0f7393a13e Refactor 'accurate' auto bed leveling to use probe_pt() 2014-02-16 10:44:15 -08:00
Gabe Rosenhouse
c4fbb44d6d Refactor 3-point auto bed leveling to use probe_pt() 2014-02-16 10:44:08 -08:00
Gabe Rosenhouse
ad2c6488c7 Add probe_pt(), useful for auto bed leveling 2014-02-16 10:38:29 -08:00
Josef Pavlik
477b6fa1df move engaged from lcd console refreshes power off timeout 2014-02-14 12:37:21 +01:00
whosawhatsis
6e43398509 G10/G11 bugfixes 
Previous version was broken by using G92 E0 between retract and recover.
 2014-02-12 13:03:00 -08:00
whosawhatsis
d6c5c503d4 correct feedrate units in comments for M207/M208 2014-02-12 13:02:47 -08:00
whosawhatsis
b5ba5c1465 Merge branch 'Marlin_v1' of https://github.com/whosawhatsis/Marlin into Marlin_v1 2014-02-11 19:06:03 -08:00
whosawhatsis
78e7654601 Keep FWRETRACT values in terms of millimeters when using M200 
for volumetric E units
 2014-02-11 19:05:35 -08:00
whosawhatsis
3f6d44d40b Keep FWRETRACT values in terms of millimeters when using M200 for volumetric E units 2014-02-11 18:50:11 -08:00
Jim Morris
b819fc53ca Add Azteeg X3 Pro as motherboard 68 
Add digipot i2c control for MCP4451
Allow M907 to set i2c digipot currents in amps
Fix Makefile to allow Azteeg motherboards
Fix Makefile to allow Wire libraries only
Add beeper pin for Azteeg X3 Pro
 2014-02-05 01:47:12 -08:00
ErikZalm
e1ae7952eb Merge pull request #743 from Opticalworm/Marlin_v1 
Improved support for panelolu2 encoder and buzzer
 2014-02-03 12:33:10 -08:00
David Forrest
a5f53f0cf3 Heater wattage reporting for M105 using EXTRUDER_WATTS and BED_WATTS 2014-02-03 14:50:28 -05:00
Ronald
8d162e5bd7 Improved support for panelolu2 encoder and buzzer 
I added #define for LCD_FEEDBACK_FREQUENCY_HZ and
LCD_FEEDBACK_FREQUENCY_DURATION_MS  which is used to alter the default
buzzer sound.

When selecting Panelolu2 in configuration.h:
- it automatically sets the correct ENCODER_PULSES_PER_STEP and
ENCODER_STEPS_PER_MENU_ITEM.
- if LCD_USE_I2C_BUZZER is defined it will also set the default
LCD_FEEDBACK_FREQUENCY_HZ and LCD_FEEDBACK_FREQUENCY_DURATION_MS

When selecting the sanguinololu 1284p the following is true:
- its now enables  LARGE_FLASH
- It enables the gcode M300 when the panelolu2 LCD_USE_I2C_BUZZER is
defined
 2014-02-03 07:45:03 +00:00
whosawhatsis
b2c11ba980 Change diameter code to 'D' 
For some reason that I can’t figure out, the decimal is dropped when
using ’S’ for the code.

Also some minor code improvements to M200.
 2014-02-01 18:49:25 -08:00
whosawhatsis
856edfcc0d Fixed math 
This is why I wanted to sleep on the code I wrote while falling asleep
rather than immediately submitting a pull request.
 2014-01-31 08:43:11 -08:00
whosawhatsis
d24df7af2c M200 implementation 2014-01-31 00:54:19 -08:00
whosawhatsis
f08bb8bb6a Previous commit borked. 2014-01-19 22:06:45 -08:00
whosawhatsis
b1f8f492c6 Remove previous_millis_cmd update from extruder runout prevention code 
This seems to defeat the purpose of previous_millis_cmd, preventing the
time elapsed from previous_millis_cmd from ever reaching
max_inactive_time or stepper_inactive_time while the heat was on.
 2014-01-19 19:22:08 -08:00
whosawhatsis
8a5eaa3c9b Fix crash after home bug 
Fixes a bug in the Extruder Runout Prevention feature that caused the
extruder to move back to “current_position” after a move if it was
activated while the move was in progress. For long home moves (which
are longer than the dimensions of the machine’s working area), this
would cause the machine to crash into the far end of its travel after
homing. This usually occurred on the Z axis, which could result in
damage to the machine if you don’t hit the reset button in time.
 2014-01-19 19:11:51 -08:00
Alex Borro
05932e4458 Add Z Probe Offset to EEPROM and Ultra LCD 2014-01-16 18:13:46 -02:00
daid
380144c20f Add Ultiboard2 electronics. With PWM current settings. For the few people that have this new board as experiment in their UM-Original. 2014-01-06 11:05:02 +01:00
fsantini
6ae7f7870d Merge branch 'Marlin_v1' of https://github.com/ErikZalm/Marlin into ErikZalm 
Conflicts:
	Marlin/Configuration.h
	Marlin/Marlin_main.cpp
 2013-12-23 12:20:32 +01:00
Francesco Santini
da2a6f9a31 Accurate bed leveling: x loop inside y and zigzag motion 2013-12-13 10:31:19 +01:00
fsantini
5bde7fcb28 Minor code and comment polishing 2013-12-11 21:27:43 +01:00
-
20faff5935 Incorporate PS_DEFAULT_OFF for starting state on LCD menu entry 2013-12-08 21:35:57 +01:00
fsantini
cc2925b705 Implemented a least squares fit of the bed equation for auto bed leveling. 
The code for the LSQ solver (qr_solve) is copyrighted by John Burkardt and released under LGPL here:
http://people.sc.fsu.edu/~%20jburkardt/c_src/qr_solve/qr_solve.html
(see qr_solve.cpp for further copyright information)
 2013-12-06 21:46:25 +01:00
fsantini
b64661070e Fixed the plane vector equation to a simpler one (only dependent on the normal) 
Removed the calculation of the inverse matrix since the rotation matrix is orthogonal, therefore inverted == transposed.
Much simpler and mathematically robust.
 2013-12-06 21:32:21 +01:00
Alex Borro
5c44f6c434 Bed Heater monitoring in Controller Fan 
In some cases the Bed Heater FET heats up more then stepper drivers, so
this change add the bed monitoring to the controller fan. As soon as the
bed heater is turned on, the controller fan will run as well.
 2013-11-27 23:23:06 -02:00
Alex Borro
b33375d438 Z Axis Safe Homing when using Z Probe 
Recommended for those who are using the Z Probe for Z Homing (as
Z-Endstop)

This feature has two changes:

1) Allow user to choose where the Z Probe will touch the bed when homing
all axis together (G28) by setting below defines:

Z_SAFE_HOMING_X_POINT
Z_SAFE_HOMING_Y_POINT

2) Prevents the user to perform Z Axis Homing when the Z Probe is
outsite bed.
 2013-11-27 22:37:35 -02:00
ErikZalm
24d1f480b6 Merge pull request #647 from shaggythesheep/newfeature-M226 
Implement M226 - GCode Initiated Pause
 2013-11-10 07:27:01 -08:00
Richard Miles
dc887ef99b Implement M226 - GCode Initiated Pause 
Implemented M226 as described here:
http://reprap.org/wiki/G-code#M226:_Gcode_Initiated_Pause

Waits for pin to be become either HIGH, LOW or the inverse of what it
was before. Allows printing to pause until user interaction
 2013-11-09 15:11:58 +00:00
Charles R
c244eb860c If you have a switch on suicide pin, this is useful if you want to 
start another print with suicide feature after a print without
suicide...
 2013-11-04 12:04:04 +01:00
dumle29
f941203172 PS_ON configurable boot state 
Allows the user to select wheter or not the PSU should be turned on or
kept in standby when marlin boots
 2013-10-29 18:44:56 +01:00
whosawhatsis
c79e3967b3 Make G11 not horribly broken 2013-10-24 18:58:42 -07:00
bkubicek
d69822ed51 Fix '#' 
since it can occure in comments.
 2013-10-22 10:34:51 +02:00
bkubicek
2fb2a0a119 Merge branch 'Marlin_v1' of https://github.com/ErikZalm/Marlin into Marlin_v1 2013-10-22 10:08:21 +02:00
bkubicek
ab965376ff Sub-file calls. 
by overloading M32 it is now possible to execute gcode files from other gcode files, with a fixed recursion level.
This can be used e.g. for having a real start.g and end.g somewhere on the sd card, which are then called from the normal print file.
Another usecase would be to have macro-files for nozzle-change and layerchange.
I have not tested the speedwise performance. The testing was done with pronterface.

syntax:
normal call from sd card will open the new file and continue executing there.
M32 !/path/filename#
this however will call the new file and return to the caller file.
M32 P !/path/filename#
with the optional "S<position>" the  file starting position can be set.
this is for continuing prints from a previous location.
 2013-10-22 10:02:18 +02:00
bkubicek
b2cc27e5ea Added a magic character for sd buffering. 
if a '#' is read now the buffer will be emptied before reading ahead.
This is so one can execute files from within gcode files, without messing the buffer with preread characters from the caller file.
# can not occure in sd files imho, because it should only occure within checksums in ther serial communication.
Yes, thats a lame argument. If you have a better idea please tell me. It has to be a character that one can type
on a keyboard manually.
 2013-10-22 09:54:13 +02:00
Erik van der Zalm
8a08cca0f2 Added temperature status less. 
Hopefully fixed viky button handling without braking other boards
 2013-10-20 12:12:35 +02:00
Erik van der Zalm
87e28c0599 Added ifdefs to blinkm 2013-10-20 09:55:15 +02:00
ErikZalm
6a803ba9c5 Merge pull request #590 from timkoster/Marlin_v1 
Added BlinkM support over i2c
 2013-10-20 00:51:35 -07:00
Alex Borro
6f85a8c7aa Bed auto Leveling change: Raise Z before homing 
- Added "Z_RAISE_BEFORE_HOMING" for raising Z the defined distance
before homing. This is useful to avoid Z-Probe collision when hotend is
near bed.

- Fixed the issue of Z not going bellow Z_PROBE_OFFSET when
"min_software_endstops" is true.
Now the Z_PROBE_OFFSET is not set in Z_MIN_POS, it is added after
homing.
 2013-10-12 17:28:11 -03:00
Alex Borro
dd3086d3f2 Show Temperature ADC values 
If "SHOW_TEMP_ADC_VALUES" is defined in Configuration_adv.h, the M105
command will present, after tradicional temperatures, the ADC value read
from temp sensors. This is great for adjusting thermistor tables with
thermocouple.

From Pronterface you can see the ADC value and compare with a
thermocouple reading.. then you just need to create your own thermistor
table.

Since this merge doesnt change the original information, it doesnt mess
with PC software parsing (tested under Pronterface and Repetier-Host).
 2013-10-12 10:41:23 -03:00
Alex Borro
253dfc4bc1 Bed Auto Leveling feature 
Check the Readme for instruction how to enable and configure the feature
 2013-09-29 13:20:06 -03:00
Tim Koster
61db046b32 Added #ifdef BLINKM around new code. Also refined BlinkM.h. 2013-09-20 10:57:42 +03:00
GDV0
f17506c504 FIx compilation error when enabling SERVO_ENDSTOPS (#591) 2013-09-11 23:09:37 +02:00
Tim Koster
7016cc9511 Added BlinkM support over i2c 2013-09-10 12:18:29 +03:00
Peter Hercek
9aa2229077 add command M666 for adjusting delta printer endstop position 2013-08-28 01:15:20 +02:00
Robert F-C
9547fb9dfb Add duplication and auto-park mode for dual x-carriage support. 2013-08-08 00:10:26 +10:00
Nicolas Rossi
a54fe2d73c Merge branch 'Marlin_v1' of https://github.com/ErikZalm/Marlin.git into Marlin_v1 
Conflicts:
	Marlin/Marlin_main.cpp
 2013-08-03 13:05:56 +02:00
hg42@gmx.net
2ca983568d separate INVERTING for MIN and MAX endstops (6 #defines instead of 3) 2013-08-01 15:06:39 +02:00
Nicolas Rossi
9bf1cf1b22 Pre-calculate diagonal rod length squared 2013-07-30 14:09:21 +02:00
Guillaume Seguin
6c42a3a339 Woops, fix logic 2013-07-30 14:02:04 +02:00
Guillaume Seguin
376d8af2c8 Report temperatures for all extruders 2013-07-30 14:02:01 +02:00
ErikZalm
434b6a05c1 Merge pull request #552 from iXce/Marlin_v1 
Report temperatures for all extruders in reply to M105
 2013-07-29 10:39:21 -07:00
Nicolas Rossi
55c287a69e Fixed move from panel for delta bot #557 2013-07-28 22:54:37 +02:00
Jim Morris
b9d7ccf1cd Merge remote-tracking branch 'upstream/Marlin_v1' into delta-configuration 
Conflicts:
	Marlin/Marlin_main.cpp
 2013-07-24 02:49:25 -07:00
Guillaume Seguin
01ed99143c Woops, fix logic 2013-07-23 23:34:42 +02:00
Guillaume Seguin
34da3a0a3f Merge github.com:ErikZalm/Marlin into Marlin_v1 
Conflicts:
	Marlin/language.h
 2013-07-23 21:46:41 +02:00
Guillaume Seguin
18199ff960 Merge github.com:ErikZalm/Marlin into Marlin_v1 2013-07-23 21:33:52 +02:00
Robert F-C
fb5334f428 Fixed compile error when QUICK_HOME is defined. 
As well a couple of minor changes to handling of extruder offset for
dual x-carriage mode.
 2013-07-22 22:46:14 +10:00
Robert F-C
39cd3dbdbe Remove dual x-carriage functionality that could/should be implemented in slicer 
Also added a couple of missed merge lines in homeaxis() from previous
commit.
 2013-07-20 13:07:50 +10:00
Jim Morris
d01ee7e7b5 fix zjerk being the same for delta as xy jerk 
add more delta defaults
on delta make second home even slower
 2013-07-17 16:14:07 -07:00
Robert F-C
d7390e13d9 Support dual x-carriage printers 
Dual x-carriage designs offer some substantial improvements for dual
extruder printing.
 2013-07-17 22:44:45 +10:00
Erik van der Zalm
59004023fd Fixed typo 2013-07-15 17:22:56 +02:00
Erik van der Zalm
461dad6e05 Added : M32 - Select file and start SD print (Can be used when printing from SD card) 
Untested
 2013-07-14 22:39:59 +02:00
Erik van der Zalm
c4a2077951 M109 and M190 now wait when cooling down if R is used instead of S. 
M109 S180 waits only when heating.
M109 R180 also waits when cooling.
 2013-07-14 21:10:24 +02:00
Michael Mayer
e509cdbeb0 added contrast control function for gLCDs 2013-07-14 15:28:26 +07:00
Gord Christmas
fde17d5720 Fix for ugly code compilation errors in SERVO_ENDSTOP checks 2013-06-28 08:02:04 -07:00
Nicolas Rossi
2daa85918e Merge branch 'Marlin_v1' of https://github.com/ErikZalm/Marlin.git into Marlin_v1 
Conflicts:
	Marlin/Configuration.h
	Marlin/Marlin_main.cpp
	Marlin/language.h
	Marlin/pins.h
	Marlin/ultralcd.cpp
 2013-06-20 23:59:56 +02:00
Erik van der Zalm
ac975ed8c2 Merge branch 'deltabot' into Marlin_v1 2013-06-10 18:20:29 +02:00
Jim Morris
caa848f943 fix homing for deltas 2013-06-09 21:10:00 -07:00
Erik van der Zalm
bd96d22bfb Merge branch 'Marlin_v1' into thinkyhead 
Conflicts:
	Marlin/Configuration.h
	Marlin/Configuration_adv.h
	Marlin/Marlin.h
	Marlin/Marlin_main.cpp
	Marlin/Servo.cpp
	Marlin/language.h
	Marlin/pins.h
	Marlin/planner.cpp
	Marlin/ultralcd_implementation_hitachi_HD44780.h
	README.md
 2013-06-09 22:26:47 +02:00
Erik van der Zalm
01edf22a10 Fix home_all_axis to make QUICK_HOME work with Repetier-Host which sends G28 X0 Y0 Z0 instead of G28. Thanks to Matt Schoenholz for reporting this issue. 2013-06-09 13:54:19 +02:00
Erik van der Zalm
373f3ecab3 Merge branch 'deltabot' of https://github.com/jcrocholl/Marlin into deltabot 
Conflicts:
	Marlin/Configuration.h
	Marlin/Marlin_main.cpp
	Marlin/pins.h
 2013-06-09 00:51:58 +02:00
Scott Lahteine
5dabc95409 Apply all changes from latest Marlin_V1 
Diffed and merged, preserving my updates
 2013-06-06 15:49:25 -07:00
Gord Christmas
a733537ddd Missed some variable declarations 
Integrated fixes from henrikbrixandersen pull request #504
 2013-06-06 09:18:03 -07:00
Gord Christmas
f4f30c9d64 Added servo actuated enstop coding to allow G28 command to engage and retract a servo to specified angles. 2013-06-06 07:36:52 -07:00
Erik van der Zalm
79374f0b93 Merge branch 'reisnyderb' of https://github.com/ErikZalm/Marlin into Marlin_v1 2013-06-05 17:44:48 +02:00
Erik van der Zalm
971ec35135 Expanded M302 to allow setting the temp 2013-06-02 17:36:23 +02:00
Erik van der Zalm
5090c56651 More redundant temp sensor changes. (After testing and debugging by reifsnderb) 2013-05-29 19:29:30 +02:00
Guillaume Seguin
16b9239a26 Report temperatures for all extruders 2013-05-29 18:06:12 +02:00
Robert F-C
40eb07bad4 Revert and extend previous change pin check change 
Reviert previous change of #if BLAH_PIN > 0 to #if defined(BLAH_PIN) &&
BLAH_PIN > -1. Unfortunately some times pin 0 is used. For my sins I've
gone through and replaced all unsafe checks of #if BLAH_PIN > -1 with
the safe version.
 2013-05-22 21:33:23 +10:00
Robert F-C
0d4a9444c4 Merge remote-tracking branch 'upstream/Marlin_v1' into Marlin_v1 2013-05-19 08:50:58 +10:00
Robert F-C
dfa549f268 Merge remote-tracking branch 'upstream/Marlin_v1' into Marlin_v1 2013-05-18 21:59:39 +10:00
Gord Christmas
dc59f07d24 First attempt at refactoring of original servo code. Only adding servo support as a start to keep things simple. 2013-05-16 07:03:01 -07:00
Erik van der Zalm
bd2cd4903e Added #ifdef BARICUDA around the BariCUDA changes 2013-05-14 23:56:32 +02:00
Jordan Miller
fbd899a37d Support for BariCUDA Paste Extruder derived from MakerBot Frostruder. Using Ultimachine RAMBo board. M126/M127 and M128/M129. 2013-05-14 23:34:45 +02:00
midopple
db2f157a22 Replace the <= to < in the Command M907, M350 and M351. 
The for loop for Axis count over the Array.
Add a break after M907
 2013-05-05 19:19:55 +02:00
Arnoud
fc4ab05157 Solved minor bug in controllerFan() 
Extruder 2 was checked where extruder 1 should be checked.
 2013-05-03 21:32:34 +02:00
Scott Lahteine
0ef54f2f85 Make M303 silent when "S0" is sent 
If S is left out perhaps it should be silent, but check the spec for
this M code.
 2013-05-02 09:55:15 -07:00
Robert F-C
d5ad7a0814 Rework change to incorporate CONTROLLERFAN 
Also refactor extruder auto fan logic to simplify further and now only
check every 2.5 seconds
 2013-04-30 01:08:29 +10:00
Robert F-C
c3cdaceab3 Merge remote-tracking branch 'upstream/Marlin_v1' into Marlin_v1 2013-04-29 22:13:55 +10:00
Robert F-C
7f57f28ccc Add lcd_buzz function to ultralcd.h so that non-LCD code can make use of lcd's buzzer. 
Argument order of lcd_buzz was set to mirror that on tone(). Change
default M300 frequency to something audible.
 2013-04-29 21:50:52 +10:00
Robert F-C
788d62bcc4 Merge remote-tracking branch 'upstream/Marlin_v1' into Marlin_v1 
Conflicts:
	Marlin/Marlin.pde
	Marlin/ultralcd.cpp
	Marlin/ultralcd_implementation_hitachi_HD44780.h
 2013-04-29 21:13:46 +10:00
Simon Oliver
5d5909fc25 Fix failure to compile with heated bed: remove call to non-existant scaleBedPID(). 2013-04-12 13:32:47 +02:00
Simon Oliver
93f0463b21 Allow Edit menu to call fn after edit; Fix PID Ki and Kd display in menus; Actually use changed PID and Max Accel values 
Add new 'callback' edit-menu types that call a function after the edit is done. Use this to display and edit Ki and Kd correctly (removing the scaling first and reapplying it after). Also use it to reset maximum stepwise acceleration rates, after updating mm/s^2 rates via menus. (Previously, changes did nothing to affect planner unless saved back to EEPROM, and the machine reset).

Add calls to updatePID() so that PID loop uses updated values whether set by gcode (it already did this), or by restoring defaults, or loading from EEPROM (it didn't do those last two). Similarly, update the maximum step/s^2 accel rates when the mm/s^2 values are changed - whether by menu edits, restore defaults, or EEPROM read.

Refactor the acceleration rate update logic, and the PID scaling logic, into new functions that can be called from wherever, including the callbacks.

Add menu items to allow the z jerk and e jerk to be viewed/edited in the Control->Motion menu, as per xy jerk.

Conflicts:
	Marlin/language.h
 2013-04-12 13:31:30 +02:00
ErikZalm
7f622467fc Merge pull request #425 from kefir-/m928_logging 
M928 logging
 2013-03-30 08:50:34 -07:00
ErikZalm
86867928ac Merge pull request #434 from DDRBoxman/Marlin_v1 
Add support for M300: Play beep sound
 2013-03-30 08:49:54 -07:00
Dirk Eichel
4e448b700a Merged fetched files from Marlin_v1 branch 
Pull requests: #414 #433 #432 #428
 2013-03-26 21:43:04 +01:00
Colin Edwards
0d075378d5 Add LARGE_FLASH define and enable it for some of the beefier boards 
The LARGE_FLASH flag allows superfluous features to be excluded
on boards with less memory
 2013-03-25 10:42:27 -05:00
Colin Edwards
9a1c90471f Ignore unused beeper pins 2013-03-25 10:28:15 -05:00
Colin Edwards
1a0f889803 Add support for M300: Play beep sound 2013-03-24 23:35:05 -05:00
blddk
e5a853a3d0 Added automated extruder fan function 2013-03-22 18:49:05 +01:00
Ketil Froyn
f036be7c4e Clean up tab/whitespace from last commit 2013-03-16 23:11:58 +01:00
Ketil Froyn
07e11c7cf5 Add command M928 to enable logging to file of received gcode commands 2013-03-16 23:02:57 +01:00
Nicolas Rossi
6504e96165 Turn off power supply off-load 
Disable the high current output and wait a little before to turn off,
because the interrupting capacity of the PSU is unknown.
Could be a function if needed by other.
 2013-03-05 15:03:48 +01:00
Nicolas Rossi
86bf911139 Toggle menu for PSU from LCD pannel 
From the prepare menu, accessible when is not printing, you have the
possibility to turn off the PSU when is on et vice versa.
From the host, you can turn off or turn on the PSU then the menu is
updated accordingly.
From the LCD message, the printer status is reported ready or off
respectively when the PSU is on or off.
 2013-03-05 14:52:51 +01:00
Robert F-C
372e12f83f Implement automatic extruder/cold-end fan control based on temperature 
This change allows fan outputs to automatically turn on/off when the
associated nozzle temperature of an extruder is above/below a threshold
temperature.
Multiple extruders can be assigned to the same pin in which case the fan
will turn on when any selected extruder is above the threshold.
It also makes the M42 command compatible with the M106/M107 command.
The majority of the logic in this change will be evaluated by the
compiler at build time (i.e, low code space requirements).
 2013-03-01 21:57:23 +11:00
Robert F-C
1292d735ba Converge all I2C LCD branches (PANELOLU2, VIKI & PCF8575) 
This includes refactoring the buttons code to remove a large amount of
non-pin dependent duplication from pins.h.
 2013-02-28 02:04:51 +11:00
daid303
4eb81a69e6 Only compile the new extruder offset code if you have multiple extruders. 2013-02-27 12:32:07 +01:00
Denis B
70871715e4 Added support for extruder offset handling 
The extruder offset can be specified in the configuration
file or adjusted on the fly using the "M218 T# X# Y#" command.
The EEPROM support is not yet merged in.
The "T#" command can take option "F#" that specifies the feedrate
at which the printing head should be re-positioned. If not
specified the re-positioning move is not preformed immediately,
but the coordinates are adjusted for the printer to properly
position the head when the next movement happens.
 2013-02-04 23:05:45 -05:00
Denis B
49b2ddc8c1 Cleaned up non-standard characters 2013-02-04 01:41:40 -05:00
Bas Spaans
19ce90fe02 Added comment about M42 usage (clean) 2013-01-31 18:20:23 +01:00
Bas Spaans
00fed0a703 Revert "Extended comment explaining M42 usage" 
This reverts commit 01541ee64c.
 2013-01-31 18:11:13 +01:00
Bas Spaans
01541ee64c Extended comment explaining M42 usage 2013-01-31 18:00:25 +01:00
Bernhard
1d06b10962 Added a feature to have filament change by gcode or display trigger. 
[default off for now]
syntax: M600  X[pos] Y[pos] Z[relative lift] E[initial retract] L[later retract distance for removal]

if enabled, after a M600, the printer will retract by E, lift by Z, move to XY, retract even more filament.
Oh, and it will display "remove filament" and beep like crazy.

You are then supposed to insert a new filament (other color, e.g.) and click the display to continue.
After having the nozzle cleaned manually, aided by the disabled e-steppers.
After clicking, the printer will then go back the whole shebang, and continue printing with a fancy new color.
 2013-01-27 13:21:34 +01:00
daid
27843388c6 Merge pull request #360 from njprossi/Marlin_v1 
Power signal control definitions for other power supplies
 2013-01-08 02:58:02 -08:00
daid303
921273baa0 Added optional feature to stop printing when an endstop is hit. Made the Z display on the LCD in 3.2 format instead of 3.1. Added LCD message when and endstop is hit. 2013-01-08 11:53:18 +01:00
Nicolas Rossi
437eb3bafc Initialize PS_ON at startup 2013-01-07 14:57:51 +01:00
Nicolas Rossi
f3c1fc70a9 Power signal control definitions for ATX and others 2013-01-07 14:33:30 +01:00
Johann Rocholl
9e7b5056a0 {X,Y,Z}_{MIN,MAX}_POS are actually in Gcode coordinates. 2012-12-28 16:20:10 -08:00
daid303
01aac2a142 Small changes on the LCD panel, let the speed control work better, line up the parameter edit the same as the menu, remove some unused defines, and remove the Z from the 10mm move menu. 2012-12-21 16:14:47 +01:00
daid303
b69cb9fbd9 Change the end of SD cart print message from minutes/seconds to hours/minutes. 2012-12-19 12:26:40 +01:00
Johann Rocholl
6dfb8a2187 Fix home_all_axis to make QUICK_HOME work with Repetier-Host which sends G28 X0 Y0 Z0 instead of G28. Thanks to Matt Schoenholz for reporting this issue. 2012-12-16 12:30:33 -08:00
Johann Rocholl
3b2e5027e5 Merged updates from Marlin_v1. 2012-12-16 12:19:24 -08:00
daid303
1a8f54cea1 The big LCD code update. This splits the display and menu implementation. Paving the way for future different displays. It also makes it easier to modify the menu structures while keeping everything consistant. Note that this most likely breaks the translations, which need to be updated. 2012-12-12 11:47:03 +01:00
daid303
6731c094ee Fix compiling with just an 16x2 LCD and no buttons. 2012-12-12 11:32:33 +01:00
daid303
b99a928a80 Fix the M117 (display message on LCD) when used over USB with checksums. 2012-12-12 09:35:32 +01:00
daid303
5ff5cee8ce Fix the sensitive pin definitions, there where analogue numbers in the digital pin list. Also made M42 without a P function on the LED_PIN (which was otherwise a useless pin definition) 2012-12-11 14:53:53 +01:00
daid303
46ec4b648c Added some missing Mxxx comments to M commands. Fixed the unsetting of the timer dividers for the fast PWM fan. 2012-12-11 10:21:44 +01:00
Johann Rocholl
8e2519e88b Add realtime delta geometry in Marlin_main.cpp. 2012-12-10 01:04:12 -08:00
daid303
c421774422 The Partial release message (which does not really tell you anything) overwrites the final print time on the LCD, which is a real shame. So I removed the message. 2012-12-05 19:32:02 +01:00
daid303
6a9bee27cc Changed the naming of some LCD functions, so the names match better what the function does. Also moved around some prototypes for general cleanup. 2012-12-03 12:52:00 +01:00
daid303
94ea26ff46 Some minor changes on code style. And a bugfix where the counters for positioning in the stepper where wrong depending on compiler settings. (Caused strange values to reported back with M114 and endstop triggers). Also fixed compiling with FWRETRACT enabled. 2012-12-03 12:13:20 +01:00
daid303
97fa2a9c30 Few simple fixes that save RAM, as static strings are stored in RAM by default. 2012-11-28 10:30:34 +01:00
Erik vd Zalm
dbbf050005 More rambo fixes 2012-11-21 20:53:56 +01:00
Erik vd Zalm
f934d0ef5b Merge remote-tracking branch 'tonokip/Marlin_v1' into Marlin_v1 
Conflicts:
	Marlin/Configuration.h
 2012-11-21 20:36:30 +01:00
daid303
43018a48c4 Fix for a few -Wextra warnings. 2012-11-12 15:35:28 +01:00
daid303
12a4d60e18 Fix the EEPROM storage, no longer inline it at multiple locations, and remove the template. 2012-11-07 10:02:45 +01:00
daid303
06b58a9c4f First cleanup. Moved all code to cpp files, so there are no dependencies on pde files. And no more odd requirement to cat files together. (Still need to fix the Makefile). Also cleaned up some defines and made defines upper case as by C coding conventions. 2012-11-06 12:06:41 +01:00