| .. |
|
stepper
|
✨ Extruder with Dual Stepper Drivers (#21403)
|
2021-06-15 00:12:20 -05:00 |
|
thermistor
|
✨ More flexible redundant temp sensor (#22085)
|
2021-06-15 00:09:52 -05:00 |
|
delta.cpp
|
🏗️ Support for up to 6 linear axes (#19112)
|
2021-06-15 00:05:03 -05:00 |
|
delta.h
|
Replace 'const float &' with 'const_float_t' (#21505)
|
2021-04-01 17:59:57 -05:00 |
|
endstops.cpp
|
🐛 Trigger existing endstops on G38 hit
|
2021-06-27 11:24:22 -05:00 |
|
endstops.h
|
✏️ Followup to Six Linear Axes (#22056)
|
2021-06-15 00:05:52 -05:00 |
|
motion.cpp
|
🐛 Fix IJK axis references, E stepper indices (#22176)
|
2021-06-21 16:26:38 -05:00 |
|
motion.h
|
⚡️ Home Z (and maybe XY) at the start of G35 (#22060)
|
2021-06-15 00:12:27 -05:00 |
|
planner_bezier.cpp
|
🏗️ Support for up to 6 linear axes (#19112)
|
2021-06-15 00:05:03 -05:00 |
|
planner_bezier.h
|
Replace 'const float &' with 'const_float_t' (#21505)
|
2021-04-01 17:59:57 -05:00 |
|
planner.cpp
|
✏️ Followup to Six Linear Axes (#22056)
|
2021-06-15 00:05:52 -05:00 |
|
planner.h
|
🏗️ Support for up to 6 linear axes (#19112)
|
2021-06-15 00:05:03 -05:00 |
|
printcounter.cpp
|
Don't display service prompt unless needed (#21654)
|
2021-04-24 00:09:51 -05:00 |
|
printcounter.h
|
Configure / disable PRINTCOUNTER save interval (#20856)
|
2021-01-26 02:30:31 -06:00 |
|
probe.cpp
|
✨ Update/extend Quiet Probing (#22205)
|
2021-06-27 11:25:07 -05:00 |
|
probe.h
|
🏗️ Support for up to 6 linear axes (#19112)
|
2021-06-15 00:05:03 -05:00 |
|
scara.cpp
|
🎨 Flags for homing directions
|
2021-05-22 16:09:18 -05:00 |
|
scara.h
|
Replace 'const float &' with 'const_float_t' (#21505)
|
2021-04-01 17:59:57 -05:00 |
|
servo.cpp
|
More IntelliSense-friendly declarations
|
2021-03-24 05:50:47 -05:00 |
|
servo.h
|
Remove extraneous 'extern' hints (#21516)
|
2021-04-02 14:22:43 -05:00 |
|
settings.cpp
|
🚸 M666: Fix value filter, add report (#22337)
|
2021-07-17 01:54:27 -05:00 |
|
settings.h
|
Optimize MarlinSettings with template methods (#21426)
|
2021-03-24 07:32:08 -05:00 |
|
speed_lookuptable.h
|
Fix links to secure sites (#18745)
|
2020-07-22 22:20:14 -05:00 |
|
stepper.cpp
|
🐛 Fix Z_MULTI_ENDSTOPS + NUM_Z_STEPPER_DRIVERS 4 compile (#22203)
|
2021-06-27 11:25:36 -05:00 |
|
stepper.h
|
🏗️ Support for up to 6 linear axes (#19112)
|
2021-06-15 00:05:03 -05:00 |
|
temperature.cpp
|
🐛 Fix manage_heaters recursion on servo move (#22313)
|
2021-07-08 23:48:51 -05:00 |
|
temperature.h
|
🎨 Check flags without ENABLED
|
2021-07-17 01:54:27 -05:00 |
|
tool_change.cpp
|
🏗️ Support for up to 6 linear axes (#19112)
|
2021-06-15 00:05:03 -05:00 |
|
tool_change.h
|
Tool sensors (#17239)
|
2021-04-16 08:02:31 -05:00 |
