Commit Graph

2990 Commits

Author SHA1 Message Date
Christian Lefrançois
8347a9d6e4 Fix HOMING_BUMP_DIVISOR for deltas configuration
* Re-bump speed divisor should be the same for delta printer.
2015-09-03 09:26:28 -05:00
Scott Lahteine
703df2cb6c Fix error message for probe region sanity check 2015-09-03 03:27:47 -05:00
Shane Francis
4c8330c15c Trim Adjustments for Delta Configurations 2015-09-03 01:05:33 -05:00
Scott Lahteine
962120d1d2 Fix spacing in some conditional blocks 2015-08-27 20:59:09 -05:00
Richard Wackerbarth
20b4772155 Create DEBUG_LEVELING_FEATURE 2015-08-27 20:52:08 -05:00
Scott Lahteine
194f98ff95 Debug messages for homing and leveling 2015-08-27 20:52:08 -05:00
Richard Wackerbarth
6292d9e815 Rename ENABLE_AUTO_BED_LEVELING
With the introduction of the #if ENABLED(…)

reads better than
2015-08-27 20:52:08 -05:00
Richard Marko
91fd66ffba add Lulzbot TAZ4 example configuration (PR#104) 2015-08-27 08:36:43 -05:00
Wurstnase
7a275773ee remove colon in utf_mapper.h (PR#106) 2015-08-27 07:15:23 -05:00
Chris Bruner
6b4b6fa315 update for newest version of U8glib_Arduino 2015-08-26 19:52:59 -05:00
Christian Lefrançois
9897a9147c Update ABL comments (PR#95)
* Updates the auto bed leveling comments ONLY.
* Renames "Z probe" word usage in //comments and #errors properly.
2015-08-26 05:51:38 -05:00
Christian Lefrançois
a7822e3ff7 Some renaming of Z_PROBE to Z_MIN_PROBE (PR#91)
* Fix a couple of renames omission and macro expansion errors.
2015-08-20 06:04:46 -05:00
Richard Wackerbarth
ad90e851b3 Use a small unsigned integer type 2015-08-16 06:56:47 -05:00
Richard Wackerbarth
29b456ae07 Suppress some compiler warnings 2015-08-16 06:56:47 -05:00
Scott Lahteine
23d742bf06 Don't free the stack array plane_equation_coefficients (PR#83) 2015-08-16 06:53:24 -05:00
Scott Lahteine
e3b1e08777 Patch G30 to use raise_z_for_servo (PR#73) 2015-08-15 21:47:04 -05:00
Scott Lahteine
a1eb90d5c0 Save another 30 bytes in gcode_SET_Z_PROBE_OFFSET 2015-08-12 21:26:32 -05:00
Scott Lahteine
91122277f4 Reduce gcode_SET_Z_PROBE_OFFSET by 88 bytes 2015-08-12 21:26:25 -05:00
AnHardt
5707a2c3d5 indexindexIntoAB is only vald for !DELTA 2015-08-11 17:32:11 -05:00
AnHardt
d8860f9ad9 Alway end at the same point
Always end at [RIGHT_PROBE_BED_POSITION, BACK_PROBE_BED_POSITION]
Regardles the evennes of auto_bed_leveling_grid_points.
2015-08-11 17:32:11 -05:00
AnHardt
4ca8f4a9a7 Always zigzag
Use the shortest way between probing-points.
2015-08-11 17:32:11 -05:00
AnHardt
3d23424121 Add array indexIntoAB[xx][yy]
and use it.
2015-08-11 17:32:11 -05:00
AnHardt
e2d69f66b2 Make Z_PROBE a Z_MIN_PROBE (PR#65)
Currently we use the probe exclusively as a device to find the build platform(bed).
For the currently supported setups this means, we use it as a additional min-endstop.
A triggered when not deployed probe disturbs the homing process for max-endstops.

Rename ENDSTOPPULLUP_ZPROBE to ENDSTOPPULLUP_ZMIN_PROBE
Rename Z_PROBE_ENDSTOP_INVERTING to Z_MIN_PROBE_ENDSTOP_INVERTING
Rename Z_PROBE_ENDSTOP to Z_MIN_PROBE_ENDSTOP
Rename DISABLE_Z_PROBE_ENDSTOP to DISABLE_Z_MIN_PROBE_ENDSTOP
Rename Z_PROBE_REPEATABILITY_TEST to Z_MIN_PROBE_REPEATABILITY_TEST
Rename Z_PROBE_ENDSTOP to Z_MIN_PROBE_ENDSTOP
Adjust comments accordingly
Remove Z_MAX  check for the probe in update_endstops().

Using an delta related idea of @clefranc from #61,
extended to the general change for all setups.

Tested with Prusa i3, max-z-endstop and permanently triggered z-probe.
Worked for @clefranc's delta.
2015-08-11 14:41:36 -05:00
AnHardt
6a6e863a47 Resolve #2581 by adding a missed ';' (PR#67) 2015-08-10 12:51:59 -05:00
RicardoGA
e09ff79635 Update pins_RAMPS_13.h (PR#64)
Now all ramps configuration can enable Filament sensor not only EEB
2015-08-10 05:53:01 -05:00
Fourmi
e6aed7bb4e Update thermistortables for Hisens Thermistor (PR#2588) 2015-08-09 18:11:14 -05:00
Richard Wackerbarth
9d8cc24abf Continue from the line following the M999 (PR#60)
If the printer is going to accept the M999,
then it should continue from that line number.
2015-08-08 08:08:02 -05:00
wurstnase
f3ab1dba54 Z babystepping for coreXY (PR#47)
only X and Y were not implemented
2015-08-04 20:10:09 -05:00
Richard Wackerbarth
35afea1c0e Restore test
PR#2572 Changed this because of faulty Boolean Logic

NOT(A OR (NOT B) OR (NOT C)) !=

(NOT A) AND ((NOT B) OR C))


Besides, the compiler should be smart enough to
optimize this without help from the programmer
2015-08-04 15:22:56 -05:00
Scott Lahteine
6af75f4b5d Squish down deprecated tests in sanity check 2015-08-03 16:04:48 -05:00
Scott Lahteine
edeb58288e Use PIN_EXISTS in sanity check 2015-08-03 16:04:48 -05:00
Scott Lahteine
c30b7693e0 Clean up RUMBA pins conditions 2015-08-03 16:04:48 -05:00
Scott Lahteine
46453905d6 Apply remaining ENABLED/DISABLED conditionals 2015-08-03 16:04:48 -05:00
Richard Wackerbarth
b227d8c128 Supply a VERSION in a short form for displays
The long descriptor will still be available in M115
2015-08-03 08:21:09 -05:00
Richard Wackerbarth
cd7828a928 This will be the 1.1.0 Release rather than 1.0.3 2015-08-03 08:08:38 -05:00
Richard Wackerbarth
4e2f5618c1 Pick up Default_version when needed 2015-08-03 08:08:37 -05:00
Richard Wackerbarth
329acc852e Canonize Option flag USE_AUTOMATIC_VERSION 2015-08-03 08:08:37 -05:00
Richard Wackerbarth
5a11d32a85 Move deprecation test to SanityCheck.h 2015-08-03 08:08:37 -05:00
Richard Wackerbarth
7bb7a52940 Bring config up-to-date 2015-08-03 07:35:33 -05:00
AnHardt
244ea2014a Boot-screen for text-displays improvements
Centred the logo for 16x4 and 20 x4.
Moved version to the bottom line
Code shrink to 704 bytes.
2015-08-03 07:13:00 -05:00
AnHardt
80f2a20842 Enable bootscreen in all Configurations 2015-08-03 07:13:00 -05:00
AnHardt
2684d061ed Scroll too long strings on bootscreen 2015-08-03 07:13:00 -05:00
AnHardt
4f46df5dab Make bootscreen configurable for the graphic displays
Saves about 473 byte of progmem and 28 bytes of RAM.
2015-08-03 07:13:00 -05:00
AnHardt
09571b7753 Boot-screen for the character displays
Uses about 488 byte of progmem and 32 byte of RAM.
For that configurable.
2015-08-03 07:13:00 -05:00
Richard Wackerbarth
866efc14fe Add Danish translations 2015-08-03 07:06:17 -05:00
Scott Lahteine
267f3479d7 Adjust spacing in pins_RAMPS_13.h 2015-08-02 23:26:58 -05:00
Scott Lahteine
56702e7bb9 Define servo pins just like other pins 2015-08-02 23:26:58 -05:00
Richard Wackerbarth
4b9d5cd352 Use lowercase names for serial instances 2015-08-02 23:01:39 -05:00
Scott Lahteine
1e2deff4fd Rename BTENABLED to BLUETOOTH
- For some reason it’s easy to forget what BT stands for, but it
doesn’t need an abbreviation.
2015-08-02 22:56:50 -05:00
Scott Lahteine
68055a5959 Include RIGIDBOT_PANEL in Conditionals 2015-08-02 22:26:41 -05:00