19f189b4e5
Add UBL support for G2/G3 and G5 ( #10648 )
2018-05-08 11:10:45 -05:00
4e16e699c1
Fix sanity checks for dual axes ( #10633 )
2018-05-07 03:34:26 -05:00
e978e6e782
[2.0.x] Arrange LCD options by type ( #10630 )
2018-05-06 19:16:55 -05:00
8c5bc77fb9
Fix the sanity-check for config versions
2018-05-06 09:37:00 -05:00
81b632c255
Additional temp-oriented improvements
2018-05-02 08:43:22 -05:00
e911635fb1
Add thermocouple with AD8495 support
2018-05-02 08:43:16 -05:00
b7e938a9fb
LCD_BED_LEVELING enables a sub-menu for ABL
2018-05-01 07:13:56 -05:00
05c33833e7
[2.0.x] Add NO_LCD_MENUS option ( #10582 )
2018-04-30 21:16:31 -05:00
616651ff23
Add sanity check for LED_CONTROL_MENU
...
Addressing #10569
2018-04-29 18:34:57 -05:00
f790b4bc0a
Reorganize some conditionals
2018-04-27 02:23:11 -05:00
df6bc812b5
Fix disable of Z_HOMING_SENSITIVITY for HOMING_Z_WITH_PROBE
...
As pointed out in #10532
2018-04-27 02:23:10 -05:00
299c4fed42
Undefine PIDTEMPBED without a bed heater
2018-04-26 01:30:10 -05:00
cb46cb8480
Add HAS_HEATED_BED conditional ( #10495 )
2018-04-23 17:13:01 -05:00
9e07df5c1b
Extra options for LEVEL_BED_CORNERS ( #10483 )
2018-04-22 02:50:48 -05:00
11ab017dd0
Creality3D Power-Loss Recovery
2018-04-21 21:56:50 -05:00
a0dac95d25
Merge pull request #10460 from thinkyhead/bf2_trigorilla_14
...
[2.0.x] Split TRIGORILLA into 1.3 and 1.4
2018-04-20 18:25:40 -05:00
f0cbf3d432
Correction to sanity check
2018-04-20 18:16:27 -05:00
80e29492c6
TRIGORILLA => TRIGORILLA_13
2018-04-20 16:12:25 -05:00
5cc7916e69
Add G29_RETRY_AND_RECOVER feature
...
- Add an option to retry G29, optionally executing a G-code procedure after each failed probe.
2018-04-19 19:45:53 -05:00
4f184ba5da
[2.0.x] Add BOARD_MKS_BASE_15 with digital micro-stepping ( #10454 )
...
* Add BOARD_MKS_BASE_15 with digital micro-stepping
* Rename MKS_13 to MKS_GEN_13
2018-04-18 22:58:43 -05:00
39c6f65ce7
Ignore LCD_BED_LEVELING with UBL
2018-04-17 15:57:44 -05:00
c9aed73987
Fix missed includes from HAL macro patch ( #10416 )
2018-04-15 18:27:34 -05:00
cc6d41e1d3
Use a macro for HAL header redirection ( #10380 )
2018-04-12 20:25:08 -05:00
12785583d0
[2.0.x] G33 MIN_STEPS_PER_SEGMENT ( #10386 )
2018-04-12 20:22:29 -05:00
c96412a78f
[2.0.x] UTF-8 language translation support ( #10213 )
2018-04-12 20:14:01 -05:00
57a899a412
[2.0.x] 6th-order jerk-controlled motion planning in real-time for AVR ( #10373 )
2018-04-11 18:13:42 -05:00
2d9b0a66fe
Add Filament Change accelerations
2018-04-09 23:57:27 -05:00
8b8ad14178
Add Z_PROBE_LOW_POINT to prevent damage
2018-04-09 17:23:03 -05:00
e02fc4f1d6
Better RESTORE_LEVELING_AFTER_G28 sanity-check
...
As suggested by @GMagician
2018-04-08 03:24:15 -05:00
a29adde5c0
Implement BEZIER_JERK_CONTROL
...
Enable 6th-order jerk-controlled motion planning in real-time.
Only for 32bit MCUs. (AVR simply does not have enough processing power for this!)
2018-04-07 21:03:28 -05:00
0e8242180d
Chamber temperature monitoring and auto fan control.
...
This is an initial cut for feedback, updated for 2.0.x.
Chamber temperature is currently reported along with hot end and bed
temperatures to serial. The format is just like that used for hot end
and bed temperatures, but using 'C' prefix. As there is no heater,
target is always 0. Is this appropriate, is there a better way to report
chamber temperatures?
Chamber temperatures are not reported on the LCD in any way.
When auto chamber fan is enabled, it currently just uses the same
temperature threshold as the other auto controlled fans.
As the chamber temperature is not connected to any heater, it doesn't
undergo mintemp/maxtemp monitoring. This would need to change in the
future if chamber heating became a feature.
2018-04-06 23:09:06 -05:00
75037493fa
Default active low for TMC2130 DIAG1 ( #10294 )
...
- Added sanity check to inform users to set the endstop to inverting
when using SENSORLESS_HOMING
2018-04-06 19:48:46 -05:00
7cbbc2af7a
[2.0.x] Optional heater signal inversion ( #10260 )
2018-04-02 19:37:41 -05:00
adcb87f0db
Z Endstop Servo => Z Probe Servo
2018-04-01 23:54:21 -05:00
49f384a2ab
Note about MKS_MINI_12864 in sanitycheck
2018-03-31 22:52:23 -05:00
f6d13e2295
Allow Z_SAFE_HOMING sanity checks to handle floats
2018-03-31 19:01:56 -05:00
1be955e52a
Alert users about low Z jerk values
2018-03-28 23:08:33 -05:00
a891af2f7a
Enforce minimum TMC2130 / TMC2208 libs
2018-03-24 15:57:22 -04:00
433e984d1f
move comment to fix compile error
2018-03-24 13:44:54 -05:00
b756a15aba
another needs to be deleted
2018-03-24 10:22:03 -05:00
50c81ebe0d
remove check that always fails
2018-03-24 09:36:50 -05:00
3ac135cef3
Enforce minimum TMC2130 / TMC2208 libs
2018-03-23 18:05:23 -04:00
97e8a6ebd9
Various fixes for DUE... ( #10152 )
...
- Watchdog reset during SD Card initialization.
- Move `DebugMonitor` to `DebugMonitor_Due.cpp`.
- Since the watchdog is enabled on boot do extra resets during init.
- Have `thermalManager` do watchdog reset before its ISR starts to prevent reset.
- Ensure that timers are stopped before reprogramming them to address tone issues.
- Improve SAM3XE reset when reflashed through the native port.
2018-03-21 19:04:45 -05:00
987597532c
For MK2_MULTIPLEXER undef DISABLE_INACTIVE_EXTRUDER
...
Fix #10098
2018-03-21 04:34:50 -05:00
dd2949922b
Consolidate 3-point leveling point options
2018-03-19 04:12:20 -05:00
1d22609473
MIN_PROBE_EDGE replaces DELTA_PROBEABLE_RADIUS
2018-03-19 04:11:46 -05:00
d603e655d3
Fix SWITCHING_EXTRUDER manual movement
2018-03-16 03:22:56 -05:00
5f77816772
Reduce size of "only one" sanity checks
2018-03-16 02:43:02 -05:00
e7570f3195
Improve TMC config organization, naming
2018-03-14 00:18:41 -05:00
14c03cb6f4
[2.0.x] Make MIN_PROBE_EDGE a general option (for electronic probes) ( #10069 )
...
Some probes don't work near the edges of the bed. This change promotes MIN_PROBE_EDGE to a general setting that applies to all probing functions.
2018-03-13 01:15:22 -05:00
