ErikZalm
36a746d7d5
Merge pull request #244 from markfinn/pidbed
...
PID for heated bed
2012-10-08 11:15:16 -07:00
Mark Finn
04631d2250
cleanup for pull
2012-09-17 14:17:24 -05:00
ZetaPhoenix
c6caa45ae2
Limit Switch locations based on MIN/MAX limits and homing direction
...
fixes #246
Added statements to set the limit switch positions to the maximum travel if homing in the positive direction as well as bed center at (0,0) if defined.
Relocated code based on feedback.
2012-09-15 15:25:49 -07:00
tonokip
1c1fddc7ac
Added support for the Rambo reprap electronics board. Added Mcodes to set
...
motor current and microstepping pins.
2012-08-30 00:16:57 -07:00
Enchiridion
50cde90324
Added support for dual Z axis stepper drivers
2012-08-04 00:32:26 -06:00
daid
12de8fff81
Support step motor controllers with active low step pins.
2012-06-29 16:27:47 +02:00
Bernhard
0c123950e9
__ header file replace
2012-06-02 20:44:17 +02:00
Bernhard
bf077125b9
added firmware retract. disabled by default
2012-06-02 20:32:28 +02:00
Erik van der Zalm
67cf105bc6
Fixed AUTOTEMP (M109 S215 B260 F1 starts autotemp)
...
Changed SLOWDOWN. IF this does not work ok OLD_SLOWDOWN is the old algo.
2012-04-15 19:17:33 +02:00
Erik van der Zalm
4ca2f336f0
Changed default MINIMUM_PLANNER_SPEED -> 0.05
...
Fixed small bug in arcs
M105 prints now actual_temp/target_temp
2012-04-01 16:23:40 +02:00
Bernhard
1532200435
found error in filenames.
...
One array was too short. This had nothing to do with long filenames, other than if they were 12 characters exactly, which could only happen if the extension and the text before were filled completely
2012-03-19 20:06:58 +01:00
Erik van der Zalm
87ff2f8867
Added CONTROLLERFAN. (Controlling a fan to cool down the steppper drivers)
2012-03-11 10:44:10 +01:00
Erik van der Zalm
c6f2ec3c82
remove stop_heating_wait
2012-02-27 18:45:45 +01:00
Erik van der Zalm
018c567abf
Moved SLOWDOWN function. (jetty840)
...
Included AD595 calibration options. (daid)
2012-02-26 16:23:47 +01:00
Blair Thompson
d9f2f509d5
Added new menu items under the prepare submenu.
...
Instead of a single pre-heat, now there is pre-heat ABS and PLA options
Added defines to the configuration file to adjust preheat temperatures for both
2012-02-22 22:51:04 +00:00
Erik van der Zalm
8816ef1c64
Small fixes after merge
2012-02-21 20:36:43 +01:00
Erik van der Zalm
13e185d330
removed unused HEATING_EARLY_FINISH_DEG_OFFSET
...
Simplified stepper inactive time
2012-02-11 23:22:16 +01:00
Erik van der Zalm
5113513cb2
RC 1
2012-02-08 18:28:54 +01:00
Erik van der Zalm
d8a0c6450f
Split the configuration file in two parts.
...
One for common settings.
One for advanced settings.
2012-02-07 20:23:43 +01:00
