Commit Graph

51 Commits

Author SHA1 Message Date
Scott Lahteine
3ea6745b36 Pretty up TMC current write 2018-01-05 10:29:49 -06:00
Scott Lahteine
1c41de16d4 Trailing whitespace clean 2018-01-05 10:11:31 -06:00
Scott Lahteine
1746a7352e
Merge pull request #9042 from thinkyhead/bf2_M701_M702
[2.0.x] Improved Pause/Load/Unload, M701-M702
2018-01-04 19:41:58 -06:00
Roxy-3D
3a4e107b6b
use SERIAL_EOL(); instead of new line string 2018-01-04 16:20:18 -06:00
Roxy-3D
19e75ccf86
Add enough precision so planner.xy_skew_factor doesn't print as 0.00 2018-01-04 16:02:22 -06:00
Scott Lahteine
7541316bb4 Add M701/M702 Filament Load/Unload, M603 2018-01-04 15:07:37 -06:00
Scott Lahteine
a80f2eea23 Group leveling reports for folding 2018-01-04 03:56:36 -06:00
Thomas Moore
8afc4f8d9d Fix UBL compilation warnings 2018-01-02 21:00:06 -06:00
Scott Lahteine
5effe1590c Fix NO_VOLUMETRICS bug 2017-12-26 20:04:44 -06:00
Scott Lahteine
4b49ea1e92 General cleanup of config-store, reset_bed_level 2017-12-25 05:16:01 -06:00
Scott Lahteine
933f76fda3 Option to disable all volumetric extrusion 2017-12-19 19:51:25 -06:00
Scott Lahteine
fc9ee1a4de Fix up serial sanity check 2017-12-19 19:11:43 -06:00
teemuatlut
0cd1e91056 [2.0.x] TMC driver update (#8769) 2017-12-15 15:03:14 -06:00
victorpv
a5150c83a2 [2.0.x] Multiple updates to STM32F1 HAL (#8733)
* STM32F1 HAL

Adding files for STM32F1 HAL based on libmaple/stm32duino core.
Current persistent_store uses cardreader changes to be sent in separate
commit, but could be changed to use i2c eeprom.
There is another persistent_store implementation that uses the MCU flash memory
to emulate eeprom
Adding readme with some information about the stm32 HAL.

* Switch to Timer4 to avoid a hard reset on STM32F103C6 boards

On bluepill STM32F103C6 boards, using Timer5 results in a error() vector call. Switch to 4 since these are both general purpose, 16 bit timers.

* Add support for EEPROM emulation using Flash

Some low end machines doe not have EEPROM support. Simulate it using the last two pages of flash. Flash does not allow rewrite between erases, so skip writing the working version if that's enabled.

* Basic Pins for a malyan M200

This is a work in progress to go hand in hand with the STM32 work.

* Add support for ADC with DMA. This work has exposed a problem with the pin enumerations in STM boards vs what marlin expects (i.e, try defining PA0 as a temp pin). The hack can be removed with we go to fastio completely. To see this work, set something in adc_pins to a value like PA0 and connect your pullup resistor'd thermistor.

* Missing file - change HAL_adc_init to actually do something

We have an actual ADC init function now.

* Remove pinmode hack

Remove the pin mode hack that I was using to init PA0.

Updated Readme.md

* Several changes to timers and GPIO

Faster GPIO, and faster timer functions by accesing registers and
libmaple.
Still more changes pending for the Timer's code to skip using the
HardwareTimer class altogether.

Switch all enums to be within #defines

This change allows a user to have, for instance, TEMP_4 and TEMP_BED definied but nothing else. The enums which are not defined move "out", allowing the first ones to take the slots in the enum, and since the array is sized on ADC_PIN_COUNT, we always have the right size data and in order.

* Update Malyan M200 pins

Update Malyan M200 pins with correct fan values.

* Test all pins on actual hardware, update definitions

Some of the pin definitions were from knowlege base/pdfs. Now they've been tested against actual hardware. This should be very close to final.

* Update HAL_timers_Stm32f1.cpp

* Add sample configurations for Malyan M200

Add sample configuration for Malyan M200 without bed leveling, and move fan to auto cool E0 since this printer by default has only one fan.


Choose the timer based on MCU defintion. Timer5 is not valid on C8/CB class boards, so use Timer4 for the step timer.


readme.md update

* Updates to timers, and some stm32 boards definitiions

* Correct pin toggle macro.

* Remove duplicated Malyan M200 entry from pins.h

* Update configuration_store.cpp

* Formatting, indentation

* Formatting in HAL_Stm32f1.cpp
2017-12-10 23:12:45 -06:00
Scott Lahteine
204199e1ce Only compare XYZ to check motion 2017-12-10 23:00:00 -06:00
Scott Lahteine
6686d937fb Always report position on config load/reset 2017-12-10 21:47:14 -06:00
Scott Lahteine
a4e1d83599 Fix M503 S parameter 2017-12-06 21:23:37 -06:00
Jonathan Barchi
05f8e98c4a Fix for issue #8629 - mismatch between number of stored and loaded dummy items on non-delta machines. (#8631) 2017-12-02 19:04:58 -06:00
Scott Lahteine
0154e3480c New feature: BED_SKEW_CORRECTION 2017-12-01 19:39:49 -06:00
Scott Lahteine
91fb6231b2 Fix EEPROM V45 header, layout 2017-11-30 22:45:17 -06:00
Scott Lahteine
a9ecb975b2 Apply LINEAR_UNIT to M503 output for M200 2017-11-24 17:32:48 -06:00
Scott Lahteine
3bba7d60f3 No retroactive changes with M851 Z
If using babystep to adjust the Z probe offset, the axis will move and the mesh will be updated at the same time, causing a doubling of the Z offset over the rest of the print.

To correct for this, the current Z position would need to be modified in the opposite direction, canceling out the additional Z offset added to the mesh. This would be confusing to users, and moreover it would not be accurate without also taking the current Z fade level and current Z height into account.

It might make sense to change the mesh in the case where no babystepping is taking place, but this could be considered an undesirable side-effect of changing the `zprobe_zoffset`.

One way to remedy this would be to return to storing the mesh with `zprobe_zoffset` included, then subtracting `zprobe_zoffset` from the returned Z value. Thus, a babystep moving the Z axis up 1mm would subtract 1 from `zprobe_zoffset` while adding 1 to all mesh Z values.

Without including the `zprobe_zoffset` in the `z_values` there is no safe way to alter the mesh in conjunction with babystepping, although it's fine without it.
2017-11-18 03:36:39 -06:00
Scott Lahteine
63257dc083 Fix M503 output for M145
Fixes #7978
2017-11-15 04:00:18 -06:00
Scott Lahteine
36426af564
Merge pull request #8356 from tcm0116/2.0.x-M600
[2.0.x] Normalize load/unload length in M600
2017-11-10 19:44:08 -06:00
LVD-AC
e334efb2a7 PROBE_MANUALLY etc. 2017-11-10 19:27:33 -06:00
Scott Lahteine
cba9c1cf9e Add pre-calculated planner.e_factor 2017-11-10 03:14:24 -06:00
Thomas Moore
f34c3597dc Add delta_height variable in lieu of using home_offset 2017-11-08 22:10:08 -06:00
Thomas Moore
73ca5345e1 Fix Delta EEPROM 2017-11-07 16:48:21 +00:00
Scott Lahteine
85a62bbf46 Misc. fixes to compiler warnings, etc. 2017-11-06 22:57:05 -06:00
Roxy-3D
6324b09934
Revert "Fix EEPROM crc (#8284)" (#8292)
This reverts commit 172c36f517.
2017-11-06 19:52:05 -06:00
Rowan Meara
172c36f517 Fix EEPROM crc (#8284) 2017-11-06 19:19:30 -06:00
Scott Lahteine
1b40e9c464 Implement CNC_COORDINATE_SYSTEMS 2017-11-04 22:28:46 -05:00
Scott Lahteine
c07bbd4154 Prettify some EEPROM code 2017-11-04 22:28:46 -05:00
Scott Lahteine
817175613a
Merge pull request #8157 from thinkyhead/bf2_anet_10_servo
[2.0.x] Define a default SERVO0_PIN for Anet 1.0
2017-10-29 19:55:00 -05:00
Scott Lahteine
723f2a77f6 Implement support for Dual X and Y endstops 2017-10-29 18:56:04 -05:00
Scott Lahteine
3e8754a38a Add/correct time units on planner vars / M205 B 2017-10-29 18:47:21 -05:00
Roxy-3D
572cf0ec95 UBL able to generate mesh and save and load it on 32-bit platforms (#8015)
* Get UBL Mesh Generation, Mesh Save & Mesh Load working with 32-Bit platforms

* clean up read_data() and write_data() for non-LPC1768 HAL's

* Get read_data() and write_data() return codes consistent

All HAL's read_data() and write_data() return false if they succeed.

* Get read_data() and write_data() return codes to be consistent

Make read_data() and write_data() return true if an error happens.

* Say UBL is now checked out on machine types in default Configuration.h file.
2017-10-18 14:00:29 -05:00
Scott Lahteine
1344ca4b2f UBL no longer needs ubl_state 2017-10-14 02:18:32 -05:00
Scott Lahteine
3e3911fb81 Use planner.leveling_active for all leveling systems 2017-10-14 02:18:31 -05:00
Scott Lahteine
9a930ebec2 Make leveling_is_active a macro 2017-10-14 02:18:31 -05:00
Scott Lahteine
1adb5a6a48 Remove obsolete UBL z_offset 2017-10-13 08:22:46 -05:00
Thomas Moore
ae2173cd52 Synchronize retractions 2017-09-30 17:28:46 -05:00
Scott Lahteine
6d5fcac54a G33 changes from 1.1.x 2017-09-24 14:16:23 -05:00
GMagician
00b1b33816 Fix compiler warning 2017-09-23 15:31:51 +02:00
Scott Lahteine
64dfb46461 Move z_endstop_adj to Endstops 2017-09-21 16:27:11 -05:00
Scott Lahteine
a10451ceed Move Volumetric methods to Planner 2017-09-21 16:27:11 -05:00
Scott Lahteine
551752eac7 Consolidate "bedlevel" code 2017-09-21 16:26:47 -05:00
Scott Lahteine
63228fc453 Move volumetric flag to GCodeParser 2017-09-21 16:26:47 -05:00
Scott Lahteine
a98e9874db FWRETRACT as a feature 2017-09-21 16:26:46 -05:00
Scott Lahteine
3d8a0ab4b2 Module updates 2017-09-21 16:26:42 -05:00