New board variant, Open Motion Controller
Open Hardware board currently used by the group build of http://tvrrug.org.uk The board can be found at http://solderpad.com/folknology/open-motion-controller/ Signed-off-by: Michel Pollet <buserror@gmail.com>
This commit is contained in:
Michel Pollet
parent
aa6e6e914e
commit
5550e893d5
155
Marlin/pins.h
155
Marlin/pins.h
@ -934,6 +934,161 @@
|
||||
|
||||
|
||||
|
||||
/****************************************************************************************
|
||||
* Open Motion controller with enable based extruders
|
||||
*
|
||||
* ATMega644
|
||||
*
|
||||
* +---\/---+
|
||||
* (D 0) PB0 1| |40 PA0 (AI 0 / D31)
|
||||
* (D 1) PB1 2| |39 PA1 (AI 1 / D30)
|
||||
* INT2 (D 2) PB2 3| |38 PA2 (AI 2 / D29)
|
||||
* PWM (D 3) PB3 4| |37 PA3 (AI 3 / D28)
|
||||
* PWM (D 4) PB4 5| |36 PA4 (AI 4 / D27)
|
||||
* MOSI (D 5) PB5 6| |35 PA5 (AI 5 / D26)
|
||||
* MISO (D 6) PB6 7| |34 PA6 (AI 6 / D25)
|
||||
* SCK (D 7) PB7 8| |33 PA7 (AI 7 / D24)
|
||||
* RST 9| |32 AREF
|
||||
* VCC 10| |31 GND
|
||||
* GND 11| |30 AVCC
|
||||
* XTAL2 12| |29 PC7 (D 23)
|
||||
* XTAL1 13| |28 PC6 (D 22)
|
||||
* RX0 (D 8) PD0 14| |27 PC5 (D 21) TDI
|
||||
* TX0 (D 9) PD1 15| |26 PC4 (D 20) TDO
|
||||
* INT0 RX1 (D 10) PD2 16| |25 PC3 (D 19) TMS
|
||||
* INT1 TX1 (D 11) PD3 17| |24 PC2 (D 18) TCK
|
||||
* PWM (D 12) PD4 18| |23 PC1 (D 17) SDA
|
||||
* PWM (D 13) PD5 19| |22 PC0 (D 16) SCL
|
||||
* PWM (D 14) PD6 20| |21 PD7 (D 15) PWM
|
||||
* +--------+
|
||||
*
|
||||
****************************************************************************************/
|
||||
#if MOTHERBOARD == 90 //Alpha OMCA board
|
||||
#define KNOWN_BOARD 1
|
||||
|
||||
#ifndef __AVR_ATmega644__
|
||||
#error Oops! Make sure you have 'SanguinoA' selected from the 'Tools -> Boards' menu.
|
||||
#endif
|
||||
|
||||
#define X_STEP_PIN 21
|
||||
#define X_DIR_PIN 20
|
||||
#define X_ENABLE_PIN 24
|
||||
#define X_MIN_PIN 0
|
||||
#define X_MAX_PIN -1
|
||||
|
||||
#define Y_STEP_PIN 23
|
||||
#define Y_DIR_PIN 22
|
||||
#define Y_ENABLE_PIN 24
|
||||
#define Y_MIN_PIN 1
|
||||
#define Y_MAX_PIN -1
|
||||
|
||||
#define Z_STEP_PIN 26
|
||||
#define Z_DIR_PIN 25
|
||||
#define Z_ENABLE_PIN 24
|
||||
#define Z_MIN_PIN 2
|
||||
#define Z_MAX_PIN -1
|
||||
|
||||
#define E0_STEP_PIN 28
|
||||
#define E0_DIR_PIN 27
|
||||
#define E0_ENABLE_PIN 24
|
||||
|
||||
#define E1_STEP_PIN -1 // 19
|
||||
#define E1_DIR_PIN -1 // 18
|
||||
#define E1_ENABLE_PIN 24
|
||||
|
||||
#define E2_STEP_PIN -1 // 17
|
||||
#define E2_DIR_PIN -1 // 16
|
||||
#define E2_ENABLE_PIN 24
|
||||
|
||||
#define SDPOWER -1
|
||||
#define SDSS 11
|
||||
#define SDCARDDETECT -1 // 10 optional also used as mode pin
|
||||
#define LED_PIN -1
|
||||
#define FAN_PIN 3
|
||||
#define PS_ON_PIN -1
|
||||
#define KILL_PIN -1
|
||||
|
||||
#define HEATER_0_PIN 4
|
||||
#define HEATER_1_PIN -1 // 12
|
||||
#define HEATER_2_PIN -1 // 13
|
||||
#define TEMP_0_PIN 0 //D27 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!!
|
||||
#define TEMP_1_PIN -1 // 1
|
||||
#define TEMP_2_PIN -1 // 2
|
||||
#define HEATER_BED_PIN -1 // 14/15
|
||||
#define TEMP_BED_PIN -1 // 1,2 or I2C
|
||||
/* Unused (1) (2) (3) 4 5 6 7 8 9 10 11 12 13 (14) (15) (16) 17 (18) (19) (20) (21) (22) (23) 24 (25) (26) (27) 28 (29) (30) (31) */
|
||||
|
||||
#endif
|
||||
|
||||
#if MOTHERBOARD == 91 // Final OMCA board -- REF http://sanguino.cc/hardware
|
||||
#define KNOWN_BOARD 1
|
||||
|
||||
#if !defined(__AVR_ATmega644P__) && !defined(__AVR_ATmega644__)
|
||||
#error Oops! Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu. (Final OMCA board)
|
||||
#endif
|
||||
|
||||
#define X_STEP_PIN 26
|
||||
#define X_DIR_PIN 25
|
||||
#define X_ENABLE_PIN 10
|
||||
#define X_MIN_PIN 0
|
||||
#define X_MAX_PIN -1
|
||||
|
||||
#define Y_STEP_PIN 28
|
||||
#define Y_DIR_PIN 27
|
||||
#define Y_ENABLE_PIN 10
|
||||
#define Y_MIN_PIN 1
|
||||
#define Y_MAX_PIN -1
|
||||
|
||||
#define Z_STEP_PIN 23
|
||||
#define Z_DIR_PIN 22
|
||||
#define Z_ENABLE_PIN 10
|
||||
#define Z_MIN_PIN 2
|
||||
#define Z_MAX_PIN -1
|
||||
|
||||
#define E0_STEP_PIN 24
|
||||
#define E0_DIR_PIN 21
|
||||
#define E0_ENABLE_PIN 10
|
||||
|
||||
/* future proofing */
|
||||
#define __FS 20
|
||||
#define __FD 19
|
||||
#define __GS 18
|
||||
#define __GD 13
|
||||
|
||||
#define UNUSED_PWM 14 /* PWM on LEFT connector */
|
||||
|
||||
#define E1_STEP_PIN -1 // 21
|
||||
#define E1_DIR_PIN -1 // 20
|
||||
#define E1_ENABLE_PIN -1 // 19
|
||||
|
||||
#define E2_STEP_PIN -1 // 21
|
||||
#define E2_DIR_PIN -1 // 20
|
||||
#define E2_ENABLE_PIN -1 // 18
|
||||
|
||||
#define SDPOWER -1
|
||||
#define SDSS 11
|
||||
#define SDCARDDETECT -1 // 10 optional also used as mode pin
|
||||
#define LED_PIN -1
|
||||
#define FAN_PIN 14 /* PWM on MIDDLE connector */
|
||||
#define PS_ON_PIN -1
|
||||
#define KILL_PIN -1
|
||||
|
||||
#define HEATER_0_PIN 3 /*DONE PWM on RIGHT connector */
|
||||
#define HEATER_1_PIN -1
|
||||
#define HEATER_2_PIN -1
|
||||
#define HEATER_1_PIN -1
|
||||
#define HEATER_2_PIN -1
|
||||
#define TEMP_0_PIN 0 // ANALOG INPUT NUMBERING
|
||||
#define TEMP_1_PIN 1 // ANALOG
|
||||
#define TEMP_2_PIN -1 // 2
|
||||
#define HEATER_BED_PIN 4
|
||||
#define TEMP_BED_PIN 2 // 1,2 or I2C
|
||||
|
||||
#define I2C_SCL 16
|
||||
#define I2C_SDA 17
|
||||
|
||||
#endif
|
||||
|
||||
|
||||
#ifndef KNOWN_BOARD
|
||||
#error Unknown MOTHERBOARD value in configuration.h
|
||||
|
||||
Loading…
Reference in New Issue
Block a user