216 lines
4.5 KiB
INI
216 lines
4.5 KiB
INI
[stepper_x]
|
|
step_pin: P2.2
|
|
dir_pin: !P2.6
|
|
enable_pin: !P2.1
|
|
microsteps: 16
|
|
rotation_distance: 40
|
|
#endstop_pin: P1.29 # P1.28 for X-max
|
|
endstop_pin: tmc2130_stepper_x:virtual_endstop
|
|
position_endstop: 0
|
|
position_max: 200
|
|
homing_speed: 20
|
|
homing_retract_dist: 0
|
|
|
|
|
|
[stepper_y]
|
|
step_pin: P0.19
|
|
dir_pin: !P0.20
|
|
enable_pin: !P2.8
|
|
microsteps: 16
|
|
rotation_distance: 40
|
|
#endstop_pin: P1.27 # P1.26 for Y-max
|
|
endstop_pin: tmc2130_stepper_y:virtual_endstop
|
|
position_endstop: 0
|
|
position_max: 200
|
|
homing_speed: 20
|
|
homing_retract_dist: 0
|
|
homing_positive_dir: false
|
|
|
|
[stepper_z]
|
|
step_pin: P0.22
|
|
dir_pin: P2.11
|
|
enable_pin: !P0.21
|
|
microsteps: 16
|
|
rotation_distance: 8
|
|
#endstop_pin: P1.25 # P1.24 for Z-max
|
|
endstop_pin: probe:z_virtual_endstop
|
|
position_min: 0
|
|
position_max: 180
|
|
|
|
[stepper_z1]
|
|
step_pin: P0.1
|
|
dir_pin: P0.0
|
|
enable_pin: !P0.10
|
|
microsteps: 16
|
|
rotation_distance: 8
|
|
|
|
[extruder]
|
|
step_pin: P2.13
|
|
dir_pin: !P0.11
|
|
enable_pin: !P2.12
|
|
microsteps: 16
|
|
rotation_distance: 29.888
|
|
nozzle_diameter: 0.400
|
|
filament_diameter: 1.750
|
|
heater_pin: P2.7
|
|
sensor_type: Generic 3950
|
|
sensor_pin: P0.24
|
|
#control: pid
|
|
#pid_Kp: 22.2
|
|
#pid_Ki: 1.08
|
|
#pid_Kd: 114
|
|
min_temp: 0
|
|
max_temp: 280
|
|
|
|
[heater_bed]
|
|
heater_pin: P2.5
|
|
sensor_type: Generic 3950
|
|
sensor_pin: P0.23
|
|
#control: pid
|
|
#pid_Kp: 148.74
|
|
#pid_Ki: 29.72
|
|
#pid_Kd: 496.3
|
|
min_temp: 0
|
|
max_temp: 80
|
|
|
|
[fan]
|
|
pin: P2.3
|
|
max_power: 0.60
|
|
|
|
[mcu]
|
|
serial: /dev/serial/by-id/usb-Klipper_lpc1768_0A30000407083DAF4C46665CC22000F5-if00
|
|
|
|
[printer]
|
|
kinematics: cartesian
|
|
max_velocity: 200
|
|
max_accel: 1500
|
|
max_z_velocity: 4
|
|
max_z_accel: 100
|
|
|
|
[safe_z_home]
|
|
home_xy_position: 125, 125
|
|
speed: 30
|
|
z_hop: 5
|
|
|
|
########################################
|
|
# TMC2130 configuration
|
|
########################################
|
|
|
|
# For TMC SPI
|
|
# 1) Place jumpers on all the red pin headers under the stepper drivers
|
|
# 2) Remove jumpers from the red pin headers labeled XUART (XUART, YUART etc.)
|
|
|
|
[tmc2130 stepper_x]
|
|
cs_pin: P1.17
|
|
spi_software_miso_pin: P0.5
|
|
spi_software_mosi_pin: P4.28
|
|
spi_software_sclk_pin: P0.4
|
|
diag1_pin: !P1.29
|
|
run_current: 0.800
|
|
stealthchop_threshold: 0
|
|
driver_SGT: 25 # -64 is most sensitive value, 63 is least sensitive
|
|
|
|
[tmc2130 stepper_y]
|
|
cs_pin: P1.15
|
|
spi_software_miso_pin: P0.5
|
|
spi_software_mosi_pin: P4.28
|
|
spi_software_sclk_pin: P0.4
|
|
diag1_pin: !P1.27
|
|
run_current: 0.800
|
|
stealthchop_threshold: 0
|
|
driver_SGT: 22 # -64 is most sensitive value, 63 is least sensitive
|
|
|
|
[tmc2130 stepper_z]
|
|
cs_pin: P1.10
|
|
spi_software_miso_pin: P0.5
|
|
spi_software_mosi_pin: P4.28
|
|
spi_software_sclk_pin: P0.4
|
|
#diag1_pin: P1.25
|
|
run_current: 0.650
|
|
stealthchop_threshold: 999999
|
|
|
|
[tmc2130 stepper_z1]
|
|
cs_pin: P1.1
|
|
spi_software_miso_pin: P0.5
|
|
spi_software_mosi_pin: P4.28
|
|
spi_software_sclk_pin: P0.4
|
|
#diag1_pin: P1.25
|
|
run_current: 0.650
|
|
stealthchop_threshold: 999999
|
|
|
|
[tmc2130 extruder]
|
|
cs_pin: P1.8
|
|
spi_software_miso_pin: P0.5
|
|
spi_software_mosi_pin: P4.28
|
|
spi_software_sclk_pin: P0.4
|
|
#diag1_pin: P1.28
|
|
run_current: 0.800
|
|
stealthchop_threshold: 0
|
|
|
|
########################################
|
|
# EXP1 / EXP2 (display) pins
|
|
########################################
|
|
|
|
[board_pins]
|
|
aliases:
|
|
# EXP1 header
|
|
EXP1_1=P1.30, EXP1_3=P1.18, EXP1_5=P1.20, EXP1_7=P1.22, EXP1_9=<GND>,
|
|
EXP1_2=P0.28, EXP1_4=P1.19, EXP1_6=P1.21, EXP1_8=P1.23, EXP1_10=<5V>,
|
|
# EXP2 header
|
|
EXP2_1=P0.17, EXP2_3=P3.26, EXP2_5=P3.25, EXP2_7=P1.31, EXP2_9=<GND>,
|
|
EXP2_2=P0.15, EXP2_4=P0.16, EXP2_6=P0.18, EXP2_8=<RST>, EXP2_10=<NC>
|
|
# Pins EXP2_1, EXP2_6, EXP2_2 are also MISO, MOSI, SCK of bus "ssp0"
|
|
|
|
# See the sample-lcd.cfg file for definitions of common LCD displays.
|
|
|
|
######################################################################
|
|
# "RepRapDiscount 128x64 Full Graphic Smart Controller" type displays
|
|
######################################################################
|
|
|
|
[display]
|
|
lcd_type: st7920
|
|
cs_pin: EXP1_4
|
|
sclk_pin: EXP1_5
|
|
sid_pin: EXP1_3
|
|
encoder_pins: ^EXP2_3, ^EXP2_5
|
|
click_pin: ^!EXP1_2
|
|
#kill_pin: ^!EXP2_8
|
|
|
|
[output_pin beeper]
|
|
pin: EXP1_1
|
|
|
|
|
|
[bltouch]
|
|
sensor_pin: ^P1.25 # Pull-up (^ symbol) needed in open drain mode
|
|
control_pin: P2.0
|
|
# Some BLTouch V3 and many clones apparently require this, though mine didnt:
|
|
#pin_up_touch_mode_reports_triggered: False
|
|
x_offset: -33.0
|
|
y_offset: -37.0
|
|
z_offset: 1.5
|
|
speed: 3.0
|
|
samples: 2
|
|
|
|
[force_move]
|
|
enable_force_move: True
|
|
|
|
[verify_heater extruder]
|
|
max_error: 150
|
|
|
|
[include mainsail.cfg]
|
|
|
|
#*# <---------------------- SAVE_CONFIG ---------------------->
|
|
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
|
|
#*#
|
|
#*# [extruder]
|
|
#*# control = pid
|
|
#*# pid_kp = 28.258
|
|
#*# pid_ki = 1.095
|
|
#*# pid_kd = 182.267
|
|
#*#
|
|
#*# [heater_bed]
|
|
#*# control = pid
|
|
#*# pid_kp = 74.602
|
|
#*# pid_ki = 1.559
|
|
#*# pid_kd = 892.424
|