6f14bcaa3e
Add MAXIMUM_STEPPER_RATE, enforce in multi-stepping
...
The timing value should be properly set for ALL boards. The compiler will check and set maximum step rate calculations based on those values.
2018-06-10 16:02:47 -05:00
f74278b8b1
Add -4 thermocouple to list in configs
2018-06-07 21:04:06 -05:00
aaaf09bda2
BEZIER_JERK_CONTROL => S_CURVE_ACCELERATION
2018-05-26 18:33:51 -05:00
4b2f6e3b2b
[2.0.x] Add endstop noise filter ( #10796 )
2018-05-21 15:51:38 -05:00
b7dfc79988
Disable SERIAL_PORT_2 by default and sanity-check it ( #10748 )
2018-05-14 21:38:24 -05:00
e978e6e782
[2.0.x] Arrange LCD options by type ( #10630 )
2018-05-06 19:16:55 -05:00
e911635fb1
Add thermocouple with AD8495 support
2018-05-02 08:43:16 -05:00
b7e938a9fb
LCD_BED_LEVELING enables a sub-menu for ABL
2018-05-01 07:13:56 -05:00
c87b0e21be
Add units to probe speed comments
2018-04-30 23:50:28 -05:00
05c33833e7
[2.0.x] Add NO_LCD_MENUS option ( #10582 )
2018-04-30 21:16:31 -05:00
9e07df5c1b
Extra options for LEVEL_BED_CORNERS ( #10483 )
2018-04-22 02:50:48 -05:00
a90cbc6339
[2.0.x] Wait for bed heaters between probing ( #10472 )
2018-04-21 15:43:21 -05:00
6c535081ec
[2.0.x] Add optional menu item to toggle software endstops ( #10389 )
2018-04-13 00:24:09 -05:00
c96412a78f
[2.0.x] UTF-8 language translation support ( #10213 )
2018-04-12 20:14:01 -05:00
82dafbba33
Add Z_PROBE_LOW_POINT to example configs
2018-04-09 01:55:05 -05:00
dca69efc11
Update Bed PID comments
2018-04-08 06:44:47 -05:00
5932df7ea1
Add BEZIER_JERK_CONTROL to example configs
2018-04-07 21:03:22 -05:00
5b3bda1c16
Add Chamber Temp options to example configs
2018-04-06 23:09:06 -05:00
adcb87f0db
Z Endstop Servo => Z Probe Servo
2018-04-01 23:54:21 -05:00
dd2949922b
Consolidate 3-point leveling point options
2018-03-19 04:12:20 -05:00
14c03cb6f4
[2.0.x] Make MIN_PROBE_EDGE a general option (for electronic probes) ( #10069 )
...
Some probes don't work near the edges of the bed. This change promotes MIN_PROBE_EDGE to a general setting that applies to all probing functions.
2018-03-13 01:15:22 -05:00
28f1276286
[2.0.x] Add Z_AFTER_PROBING option ( #10058 )
...
Some "fix-mounted" probes need manual stowing. And after probing some may prefer to raise or lower the nozzle. This restores an old option but tailors it to allow raise or lower as preferred.
2018-03-11 13:07:55 -05:00
79e6d890d5
Add UNKNOWN_Z_NO_RAISE to example configs
2018-03-10 00:17:34 -06:00
a2a672449a
Updated boot screen description
2018-03-03 20:04:17 -06:00
4953fb1c88
Standardize encoder defaults
2018-02-24 22:34:45 -06:00
5684beae90
Bring some configs up to speed
2018-02-24 21:56:27 -06:00
2024775e07
Spanish (UTF8) Language ( #9786 )
...
From #7314 by @MrAmericanMike
2018-02-23 20:24:02 -06:00
17d984eab3
Add RESTORE_LEVELING_AFTER_G28 to example configs
2018-02-23 13:38:54 -06:00
7d8c6b3f3c
Add 20x4 option for Sainsmart LCD ( #9740 )
2018-02-21 00:46:25 -06:00
8733d5a296
Add NUM_RUNOUT_SENSORS to example configs
2018-02-19 07:02:50 -06:00
ca55f2927a
Pulldown pin mode support ( #9701 )
...
Implemented for LPC1768.
2018-02-18 19:26:23 -06:00
21e60fd3ed
Allow user to control Z-Height correction for off mesh movements ( #9661 )
2018-02-15 15:07:42 -06:00
2ec65051fd
Fix serial comment sp.
2018-02-13 22:40:56 -06:00
38c7d53bf7
Repair some spacing
2018-02-10 19:33:26 -06:00
b5e92f4f90
[2.0.x] Enable / disable PSU automatically ( #9503 )
2018-02-06 00:22:30 -06:00
eecb0188c0
Add ULTI_CONTROLLER to example configs
2018-02-05 22:30:03 -06:00
4925f60cff
Add MALYAN_LCD to configs
2018-02-04 18:52:44 -06:00
7d6c009104
Add thermistor 15 tuned for JGAurora A5
2018-01-22 01:27:11 -06:00
348b454401
Probe bounds based on bed size
2018-01-22 01:05:11 -06:00
fa432508b0
Followup to Ender config
2018-01-15 06:00:21 -06:00
dabb75034c
Update example configurations
2018-01-10 00:01:20 -06:00
5295b4713d
[2.0.x] add semitec 104NT-4 ( #9119 )
...
Table is very very similar to old 104-GT2 so I added only the name and recycled old ID
2018-01-09 16:53:12 -06:00
0b4a46fa6c
Bring configs up to date with 1.1.x
2017-12-30 23:28:53 -06:00
f0a8a1a853
[2.0.x] Use NOZZLE_PARK_FEATURE for ADVANCED_PAUSE_FEATURE ( #8866 )
...
* Use NOZZLE_PARK_FEATURE for ADVANCED_PAUSE_FEATURE
2017-12-25 01:38:06 -06:00
1cf1cf8759
Add RADDS_DISPLAY to example configs
2017-12-24 19:00:23 -06:00
f79026acc1
Apply MKS_12864OLED_SSD1306 to examples
...
Followup to #8814
2017-12-16 20:15:36 -06:00
9abbcc3ee0
Apply ZONESTAR_LCD to example configs
2017-12-15 19:11:02 -06:00
69d49a2438
Shorter segments may be better
2017-12-09 06:29:14 -06:00
d7800e7975
Apply MULTIPLE_PROBING to example configs
2017-12-07 16:44:12 -06:00
c1184552ac
Change K1 to required option PID_K1
2017-12-05 19:59:59 -06:00
