Scott Lahteine
b402040059
Split bed size sanity check into two
2019-01-11 15:49:57 -06:00
jmz52
813a4ea107
Add support for Mks Robin TFT display ( #12706 )
...
* Add support for MKS Robin TFT display
- Add support for MKS Robin TFT display and encoder for MKS Robin board.
- Generic 128x64 UI with x2 upscale is used (for now).
- Tested on MKS Robin TFT V2.0 with ST7789V controller.
2019-01-03 10:38:39 -06:00
Giuliano Zaro
54ba44ee37
Fix bad sanitycheck ( #12748 )
2018-12-30 10:44:15 -06:00
Ludy
cfc5e96b4b
Move JD to Config.h (and fix jerk->eeprom bug) ( #12720 )
2018-12-27 15:29:39 -06:00
Marcio Teixeira
902d5b0f8b
Allow ExtUI to use LCD_SET_PROGRESS_MANUALLY ( #12628 )
2018-12-12 17:21:37 -06:00
Dave Johnson
9a4a463ec4
Sanity-check LIGHTWEIGHT_UI, move comment up ( #12630 )
2018-12-12 16:59:20 -06:00
Marcio Teixeira
b22716e938
M425 Backlash Correction ( #11061 )
2018-12-08 14:36:46 -06:00
Scott Lahteine
fa47ce369a
Sanity-check for negative steps, feedrate, accel
2018-12-07 19:38:15 -06:00
teemuatlut
50b2fbd031
Trinamic: Split stealthChop, improve driver monitoring, etc. ( #12582 )
2018-12-07 15:34:21 -06:00
Scott Lahteine
aaf862aef2
Fix angles for disabled EDITABLE_SERVO_ANGLES ( #12559 )
2018-11-30 12:31:42 -06:00
Jacob Jordan
8be91677df
Fix Skew factors ( #12555 )
...
- Ensure Skew factors are calculated from test square measurements
2018-11-29 11:39:31 -06:00
Marcio Teixeira
439a3e8463
Improve runout sensor, fix LIGHTWEIGHT_UI screen size ( #12544 )
2018-11-27 13:45:25 -06:00
Scott Lahteine
fd2998efd5
Revert ADC_KEYPAD direction behavior ( #12508 )
2018-11-22 06:00:00 -06:00
Scott Lahteine
d29cb09b3e
Fix a minor compile warning
2018-11-22 05:35:38 -06:00
Scott Lahteine
c5642a894f
Fix ADC_KEYPAD middle button ( #12493 )
2018-11-20 21:39:30 -06:00
Ludy
1f93d2bcf7
Fix LCD compile error, etc. ( #12472 )
2018-11-18 20:39:49 -06:00
Ludy
93e958f695
Fix compile error with ZONESTAR_LCD+NO_LCD_MENUS ( #12466 )
2018-11-17 21:21:30 -06:00
Scott Lahteine
7ee5894360
Allow float XY probe offsets
...
Responding to #12383
XY probe offsets should be integers because adding decimal points makes the code larger. But if decimals are very much wanted, this commit removes the old restriction.
2018-11-17 07:44:47 -06:00
Scott Lahteine
d97e31db4c
Optimize Power-Loss Recovery ( #12440 )
2018-11-16 20:47:07 -06:00
Mateusz Krawczuk
ca21ac6b9b
Support two MAX6675 thermocouples ( #8686 )
2018-11-16 18:20:33 -06:00
Scott Lahteine
d82c350de7
Miscellaneous LCD code renaming, reordering ( #12430 )
...
* Move special characters to language.h
* Apply some naming standards
* Clean up menu item draw functions
* Rename some Temperature methods
* UI => ExtUI
2018-11-14 13:13:51 -06:00
Scott Lahteine
ebf585b673
Fix an old sanity check
2018-11-14 01:15:35 -06:00
Scott Lahteine
0ee1a92971
Group status methods, share reset_status with Extensible UI ( #12414 )
...
* Group status methods, share reset_status with Extensible UI
* Move common DOGM code to headers
2018-11-13 01:47:45 -06:00
Scott Lahteine
a3923424c7
Clean up LCD width/height determination
2018-11-12 02:37:40 -06:00
Scott Lahteine
a0c795b097
Encapsulate common display code in a singleton ( #12395 )
...
* Encapsulate common LCD code in a singleton
* Depend more UBL code on UBL_DEVEL_DEBUGGING
- Since most users don't need the debugging on at all times, this helps reduce the default build size for UBL by over 2K, a little closer to fitting on 128K boards.
2018-11-11 12:16:24 -06:00
revilor
b60abc7c37
[2.0.x] Macro G-codes ( #9365 )
2018-11-09 05:25:08 -06:00
Scott Lahteine
4ed6397e5d
More comprehensive NO_LCD_MENUS ( #12367 )
2018-11-09 00:07:16 -06:00
Scott Lahteine
b169320a03
Clean trailing whitespace
2018-11-07 02:40:18 -06:00
InsanityAutomation
6471a75a22
Combine more tool-change variables ( #12137 )
2018-11-06 22:22:20 -06:00
Scott Lahteine
e574f01568
More advanced pause tweaks ( #12356 )
...
* Followup to LCD_TIMEOUT_TO_STATUS=0
* Make continuous purge screen fit 20x4
* Unify purge message modes
* Preserve last-set pause header mode
2018-11-06 19:25:57 -06:00
Scott Lahteine
427bc64ba1
G28 O respects HOME_AFTER_DEACTIVATE
...
Addressing #11271
2018-11-05 04:17:37 -06:00
Scott Lahteine
498dfa291e
Update and fix CHDK
2018-11-05 04:17:37 -06:00
Scott Lahteine
d5ab4cd22a
Provide a default for Z_PROBE_LOW_POINT
2018-11-05 04:17:37 -06:00
KangDroid
82ff7c6542
Add a mesh edit menu for MBL / ABL-Bilinear
2018-11-04 19:07:47 -06:00
Scott Lahteine
44fa7fb18c
Cleanups for leveling-related code
2018-11-04 19:07:47 -06:00
Scott Lahteine
cd066bfeba
Extend error messages for E factors sanity-checks
2018-11-04 18:42:56 -06:00
Ludy
c10edb0998
Update, correct sanity-checks for up to 6 extruders ( #12333 )
2018-11-04 18:36:45 -06:00
Scott Lahteine
f5eab912ed
Apply #pragma once, misc cleanup ( #12322 )
...
* Apply #pragma once in headers
* Adjust some thermistors formatting
* Misc cleanup and formatting
2018-11-04 02:25:55 -06:00
Scott Lahteine
d1ff22b983
Revive SCARA's home offset (unimplemented)
2018-11-03 06:24:41 -05:00
Scott Lahteine
2c9586be0c
Clear up HAS_WORKSPACE_OFFSET meaning
2018-11-03 04:06:37 -05:00
Ludy
5ba6607181
Fix keypad-related compile error ( #12306 )
2018-11-02 22:29:32 -05:00
Scott Lahteine
3eb9838dca
Simplify TMC sanity-checks
2018-11-02 01:15:49 -05:00
Scott Lahteine
31c28d0dd2
Drop pgm_read_*_near and let headers choose ( #12301 )
...
- Drop `pgm_read_*_near` and let headers choose.
- Define `USE_EXECUTE_COMMANDS_IMMEDIATE` as a conditional.
- Add `process_subcommands_now` for SRAM-based commands.
2018-11-02 00:42:16 -05:00
Ludy
9f77df2590
Followup to menu refactor. TMC warnings, sanity. ( #12288 )
...
- Followup fixes for menu refactor
- Fix TMC sanity checks, unused var warnings
2018-11-01 16:13:33 -05:00
Scott Lahteine
3583e2b449
Followup to Menu Refactor ( #12275 )
2018-10-30 16:34:45 -05:00
TheLongAndOnly
5536228359
G34 Auto-align multi-stepper Z axis ( #11302 )
2018-10-29 14:01:36 -05:00
Scott Lahteine
182b1405d9
LCD conditionals in configurations
2018-10-28 15:46:45 -05:00
Scott Lahteine
2bf18950ab
Refactor LCD menus
2018-10-28 15:46:45 -05:00
Scott Lahteine
ab8425f1b5
Clean up PROBE_TRIGGERED_WHEN_STOWED_TEST ( #12232 )
2018-10-26 19:18:20 -05:00
Chris Rigter
3028a620af
Add RACK_AND_PINION_PROBE ( #12218 )
2018-10-26 18:24:24 -05:00