bissen21/Marlin_Firmware
1
0
Fork 0
Code Issues Pull Requests Projects Releases 4 Wiki Activity
14,270 Commits 1 Branch 4 Tags 151 MiB
2460a3dfbb
Commit Graph

763 Commits

Author SHA1 Message Date
Jacob Jordan
8be91677df Fix Skew factors (#12555) 
- Ensure Skew factors are calculated from test square measurements
 2018-11-29 11:39:31 -06:00
Marcio Teixeira
439a3e8463 Improve runout sensor, fix LIGHTWEIGHT_UI screen size (#12544) 2018-11-27 13:45:25 -06:00
Scott Lahteine
fd2998efd5
Revert ADC_KEYPAD direction behavior (#12508) 2018-11-22 06:00:00 -06:00
Scott Lahteine
d29cb09b3e Fix a minor compile warning 2018-11-22 05:35:38 -06:00
Scott Lahteine
c5642a894f
Fix ADC_KEYPAD middle button (#12493) 2018-11-20 21:39:30 -06:00
Ludy
1f93d2bcf7 Fix LCD compile error, etc. (#12472) 2018-11-18 20:39:49 -06:00
Ludy
93e958f695 Fix compile error with ZONESTAR_LCD+NO_LCD_MENUS (#12466) 2018-11-17 21:21:30 -06:00
Scott Lahteine
7ee5894360 Allow float XY probe offsets 
Responding to #12383

XY probe offsets should be integers because adding decimal points makes the code larger. But if decimals are very much wanted, this commit removes the old restriction.
 2018-11-17 07:44:47 -06:00
Scott Lahteine
d97e31db4c
Optimize Power-Loss Recovery (#12440) 2018-11-16 20:47:07 -06:00
Mateusz Krawczuk
ca21ac6b9b Support two MAX6675 thermocouples (#8686) 2018-11-16 18:20:33 -06:00
Scott Lahteine
d82c350de7
Miscellaneous LCD code renaming, reordering (#12430) 
* Move special characters to language.h
* Apply some naming standards
* Clean up menu item draw functions
* Rename some Temperature methods
* UI => ExtUI
 2018-11-14 13:13:51 -06:00
Scott Lahteine
ebf585b673 Fix an old sanity check 2018-11-14 01:15:35 -06:00
Scott Lahteine
0ee1a92971
Group status methods, share reset_status with Extensible UI (#12414) 
* Group status methods, share reset_status with Extensible UI
* Move common DOGM code to headers
 2018-11-13 01:47:45 -06:00
Scott Lahteine
a3923424c7 Clean up LCD width/height determination 2018-11-12 02:37:40 -06:00
Scott Lahteine
a0c795b097
Encapsulate common display code in a singleton (#12395) 
* Encapsulate common LCD code in a singleton
* Depend more UBL code on UBL_DEVEL_DEBUGGING
  - Since most users don't need the debugging on at all times, this helps reduce the default build size for UBL by over 2K, a little closer to fitting on 128K boards.
 2018-11-11 12:16:24 -06:00
revilor
b60abc7c37 [2.0.x] Macro G-codes (#9365) 2018-11-09 05:25:08 -06:00
Scott Lahteine
4ed6397e5d
More comprehensive NO_LCD_MENUS (#12367) 2018-11-09 00:07:16 -06:00
Scott Lahteine
b169320a03 Clean trailing whitespace 2018-11-07 02:40:18 -06:00
InsanityAutomation
6471a75a22 Combine more tool-change variables (#12137) 2018-11-06 22:22:20 -06:00
Scott Lahteine
e574f01568
More advanced pause tweaks (#12356) 
* Followup to LCD_TIMEOUT_TO_STATUS=0
* Make continuous purge screen fit 20x4
* Unify purge message modes
* Preserve last-set pause header mode
 2018-11-06 19:25:57 -06:00
Scott Lahteine
427bc64ba1 G28 O respects HOME_AFTER_DEACTIVATE 
Addressing #11271
 2018-11-05 04:17:37 -06:00
Scott Lahteine
498dfa291e Update and fix CHDK 2018-11-05 04:17:37 -06:00
Scott Lahteine
d5ab4cd22a Provide a default for Z_PROBE_LOW_POINT 2018-11-05 04:17:37 -06:00
KangDroid
82ff7c6542 Add a mesh edit menu for MBL / ABL-Bilinear 2018-11-04 19:07:47 -06:00
Scott Lahteine
44fa7fb18c Cleanups for leveling-related code 2018-11-04 19:07:47 -06:00
Scott Lahteine
cd066bfeba Extend error messages for E factors sanity-checks 2018-11-04 18:42:56 -06:00
Ludy
c10edb0998 Update, correct sanity-checks for up to 6 extruders (#12333) 2018-11-04 18:36:45 -06:00
Scott Lahteine
f5eab912ed
Apply #pragma once, misc cleanup (#12322) 
* Apply #pragma once in headers
* Adjust some thermistors formatting
* Misc cleanup and formatting
 2018-11-04 02:25:55 -06:00
Scott Lahteine
d1ff22b983 Revive SCARA's home offset (unimplemented) 2018-11-03 06:24:41 -05:00
Scott Lahteine
2c9586be0c Clear up HAS_WORKSPACE_OFFSET meaning 2018-11-03 04:06:37 -05:00
Ludy
5ba6607181 Fix keypad-related compile error (#12306) 2018-11-02 22:29:32 -05:00
Scott Lahteine
3eb9838dca Simplify TMC sanity-checks 2018-11-02 01:15:49 -05:00
Scott Lahteine
31c28d0dd2
Drop pgm_read_*_near and let headers choose (#12301) 
- Drop `pgm_read_*_near` and let headers choose.
- Define `USE_EXECUTE_COMMANDS_IMMEDIATE` as a conditional.
- Add `process_subcommands_now` for SRAM-based commands.
 2018-11-02 00:42:16 -05:00
Ludy
9f77df2590 Followup to menu refactor. TMC warnings, sanity. (#12288) 
- Followup fixes for menu refactor
- Fix TMC sanity checks, unused var warnings
 2018-11-01 16:13:33 -05:00
Scott Lahteine
3583e2b449
Followup to Menu Refactor (#12275) 2018-10-30 16:34:45 -05:00
TheLongAndOnly
5536228359 G34 Auto-align multi-stepper Z axis (#11302) 2018-10-29 14:01:36 -05:00
Scott Lahteine
182b1405d9 LCD conditionals in configurations 2018-10-28 15:46:45 -05:00
Scott Lahteine
2bf18950ab Refactor LCD menus 2018-10-28 15:46:45 -05:00
Scott Lahteine
ab8425f1b5
Clean up PROBE_TRIGGERED_WHEN_STOWED_TEST (#12232) 2018-10-26 19:18:20 -05:00
Chris Rigter
3028a620af Add RACK_AND_PINION_PROBE (#12218) 2018-10-26 18:24:24 -05:00
Scott Lahteine
e8031b1152 Add Custom Microstepping options 2018-10-25 11:26:32 -05:00
TheSFReader
a07ac6312f G0 feedrate may be fixed or variable (#12172) 2018-10-25 10:35:16 -05:00
Ludy
a93e9e6e9b Use preheat labels in place of PLA/ABS (#12194) 2018-10-23 15:38:17 -05:00
Scott Lahteine
e229b831fa Customizable preheat labels 2018-10-23 00:57:50 -05:00
Scott Lahteine
b641571098 Replace types.h with millis_t.h 2018-10-20 23:07:12 -05:00
Scott Lahteine
67a3c5a16a
Alternative info screen (Prusa-style) (#12132) 
* Fix Z value display
* Add HAS_PRINT_PROGRESS
* Alternative Info Screen option
* Add LCD_INFO_SCREEN_STYLE to example configs
 2018-10-18 11:34:52 -05:00
Hannes Brandstätter-Müller
c36773bffb Update the Ender-4 example config (#12131) 
- Enable filament change menu
- Enable bed-PID
- Enable s-curve acceleration
- Enable some menu items
- Update from Skorpi's new version
- Fix extruder steps, deactivate nozzle clean feature
 2018-10-17 15:49:52 -05:00
InsanityAutomation
3ec3872730 Single Z raise value for all tool-changing / parking (#12090) 
* Universal tool-change Z lift
* Add TOOLCHANGE_ZRAISE to example configs
* Park/unpark changes to example configs
* Implement DEBUG_DXC_MODE
 2018-10-17 11:11:41 -05:00
Scott Lahteine
8bf596bd4c RETRACT_ZLIFT => RETRACT_ZRAISE 2018-10-16 16:46:40 -05:00
Scott Lahteine
0139762a96 Fix a sanity check 2018-10-16 05:46:33 -05:00
AnHardt
f56968ba0b New Continuous Filament Mixer (#12098) 2018-10-16 03:38:57 -05:00
Scott Lahteine
951b25163e
Extend M217 with configurable park/raise (#12076) 2018-10-13 23:08:20 -05:00
Scott Lahteine
1407afad73 Move SENSITIVE_PINS to its own file 2018-10-11 01:10:11 -05:00
Scott Lahteine
45e738876a Add stepper MS3 support 
Co-Authored-By: TheLongAndOnly <thelongandonly@users.noreply.github.com>
 2018-10-11 01:10:11 -05:00
Giuliano Zaro
d43d4e4219 Refactor PRINTER_EVENT_LEDS, apply to M303 (#12038) 
Co-Authored-By: Giuliano Zaro <gmagician@users.noreply.github.com>
 2018-10-10 21:25:43 -05:00
Scott Lahteine
cf5284cdf2
Add SD Firmware Update capability (#12043) 
Co-Authored-By: timoxd7 <timoxd7@users.noreply.github.com>
 2018-10-09 20:00:47 -05:00
Marcio Teixeira
906a24fa81 Extensible user interface API (#11193) 2018-10-08 15:44:05 -05:00
InsanityAutomation
ee253991d4 Various fixups for single-nozzle filament swap (#12036) 2018-10-08 15:39:55 -05:00
Scott Lahteine
7db0113b53 Improve E_AXIS_N macro 2018-10-07 18:22:05 -05:00
InsanityAutomation
74cd6cb4fc Single nozzle filament change (#11994) 2018-10-07 17:06:14 -05:00
teemuatlut
c447d75916 Add support for TMC2660 (#11998) 2018-10-06 17:18:10 -05:00
Marcio Teixeira
2067619a26 Add USB_FLASH_DRIVE_SUPPORT 2018-10-04 19:54:12 -05:00
teemuatlut
c3229e1b34 Migrate to a new TMC library (#11943) 2018-10-03 02:48:49 -05:00
Scott Lahteine
ee53f7d813 Revert header reorg. 2018-10-02 22:09:41 -05:00
Scott Lahteine
0dedb3e139
Reorganize some core headers (#11983) 2018-10-02 04:25:46 -05:00
Scott Lahteine
f4c625d3a1 Ensure MIN/MAX overrides 2018-10-01 05:32:55 -05:00
AnoNymous
b30ca652ae Replace MIN# / MAX# with variadic MIN / MAX (#11960) 2018-09-30 04:59:14 -05:00
Scott Lahteine
e2ab78d876 Fix SERIAL_PORT_2 sanity check 2018-09-30 00:24:10 -05:00
Thomas Moore
3286325044 Add TMC2130 sensorless probing 2018-09-29 18:54:14 -05:00
Scott Lahteine
bdc9889d3a Fix a sanity check 2018-09-29 00:24:25 -05:00
Scott Lahteine
5490a664f5
Expose: Homing Validation and Endstop Noise Threshold (#11912) 2018-09-24 21:59:12 -04:00
Scott Lahteine
cee34f7290
Followup for BABYSTEP_HOTEND_Z_OFFSET (#11916) 2018-09-24 21:46:56 -04:00
Scott Lahteine
10590c2f80 Fix some fan conditionals 2018-09-18 21:23:33 -05:00
Scott Lahteine
1718eff54a Code changes supporting up to 6 extruders 2018-09-16 22:32:53 -05:00
Thomas Moore
c437bb08f1 Overhaul of the planner (#11578) 
- Move FWRETRACT to the planner
- Combine leveling, skew, etc. in a single modifier method
- Have kinematic and non-kinematic moves call one planner method
 2018-09-16 21:24:15 -05:00
Holger Müller
1a6f2b29b8 Add support for Triple-Z steppers/endstops 2018-09-16 00:35:58 -05:00
Scott Lahteine
8584d3697d Fix servo count define conflict 
`MAX_SERVOS` => `NUM_SERVO_PLUGS`
 2018-09-11 16:20:31 -05:00
Scott Lahteine
eafd62308e
Use TMC2208Stepper v0.2.5 (#11714) 2018-09-08 20:41:21 -05:00
Kevin
e25d2ae4a2 [2.0.x] SWITCHING_TOOLHEAD (#11623) 2018-09-08 01:43:24 -05:00
Scott Lahteine
b213a89ef5 Sanity-check NOZZLE_PARK_POINT 2018-09-05 06:18:08 -05:00
Scott Lahteine
8e18e48d49
Merge pull request #11610 from Freeviv/bugfix-2.0.x 
[2.0.x] Editable servo angles
 2018-09-03 03:55:38 -05:00
teemuatlut
49e107cea9 Restrict SW serial to AVR (#11696) 2018-09-01 15:24:44 -05:00
Scott Lahteine
18f1af2dca Fix up Teensy tests, servo sanity 2018-09-01 01:10:20 -05:00
Scott Lahteine
d55f44edba
Printcounter improvements (#11689) 2018-08-31 17:40:39 -05:00
Scott Lahteine
136860e8bb Sanity-check SERVO pin for servo probes 2018-08-31 15:47:47 -05:00
Scott Lahteine
3e81745e81 Fix issues, make optional 2018-08-29 17:58:02 -05:00
Scott Lahteine
d1c9517903 Followup to hotend_offset[Z] patch 2018-08-24 21:32:00 -05:00
Scott Lahteine
acf5ae3083 !ENABLED => DISABLED 2018-08-24 16:36:37 -05:00
Chris Pepper
5573ef62c6 [2.0.x] PersistentStore update followup (#11549) 2018-08-14 17:54:12 -05:00
Dave Johnson
c64199941e Compile only selected PIO environment (#11519) 2018-08-14 03:28:52 -05:00
Scott Lahteine
6964e1a95a Clean up trailing whitespace 2018-08-14 00:55:37 -05:00
Scott Lahteine
b328fb4dc9
Treat TMC2660 like non-TMC (#11508) 2018-08-10 00:30:28 -05:00
Greg Nutt
a1a5367380 Smoothieboard V1.0/1.1 and A5984 support 2018-08-09 23:03:17 -05:00
Scott Lahteine
131d216afa
Fix drivers.h dependency, defer macro evaluation (#11450) 2018-08-03 21:49:04 -05:00
Scott Lahteine
9c62c47579
[2.0.x] Fix Dual X Carriage tool change crash (#11447) 2018-08-03 20:47:29 -05:00
Lee Olivares
094e6d81a5 Add Einstart-S support (#11219) 
Indeed the HAL does not need to be mucked around with to expose ATmega2560 pins not available as numbers on the MEGA board, I'll need to update the wiki with that tidbit and a reference to the pin-mapping comment in `fastio_1280.h`.
 2018-07-26 05:52:22 -05:00
Bo Herrmannsen
67b205fd45 Add support for board RuRAMPS4D v1.3 (#11363) 2018-07-25 19:32:27 -05:00
teemuatlut
fbcdf5eaeb Simplify stepper driver per-axis selection 2018-07-25 02:47:43 -05:00
Scott Lahteine
bf7d0ba859 Assert that XY probe offsets are integers 2018-07-12 22:48:07 -05:00
Scott Lahteine
25e2ca8896 Add Z_CLEARANCE_MULTI_PROBE 
Co-Authored-By: nightgryphon <ngryph@gmail.com>
 2018-07-12 22:46:34 -05:00
Scott Lahteine
68e6650df7 Remove Quake Fast Inverse SQRT (it isn't faster) 2018-07-04 22:22:10 -05:00
Scott Lahteine
480a3d3d0c Apply sensorless homing requirements only for specified axes 2018-07-03 19:16:09 -05:00
Scott Lahteine
1ea222e6fc Turn off DISABLE_INACTIVE_EXTRUDER with SWITCHING_NOZZLE 
Fix #11183
 2018-07-02 17:26:53 -05:00
Scott Lahteine
8eaac0dab3
Add delta feedrate scaling (#11153) 2018-06-30 13:44:27 -05:00
Colin Gilgenbach
0fff79c24b Fixes G29_with_retry behavior (#11045) 
* Fix G29 (ABL) retry behavior
 2018-06-29 20:48:11 -05:00
Scott Lahteine
1b8973eb1c Fix up microsteps conditionals 2018-06-27 23:41:32 -05:00
Scott Lahteine
053438a3aa
Poll all endstops, even when stationary (#11123) 2018-06-27 04:18:57 -04:00
Scott Lahteine
7a84b03796 Use MIN/MAX in post-conditionals 2018-06-20 03:15:19 -05:00
Scott Lahteine
d4795e5b8e
[2.0.x] Tweaks and additions for MAX7219 (#11034) 2018-06-18 22:04:03 -05:00
Scott Lahteine
0d79128c8d Localize stepper-specific defines 2018-06-12 21:16:54 -05:00
etagle
6f14bcaa3e Add MAXIMUM_STEPPER_RATE, enforce in multi-stepping 
The timing value should be properly set for ALL boards. The compiler will check and set maximum step rate calculations based on those values.
 2018-06-10 16:02:47 -05:00
etagle
39a7e7720d Adaptive multiaxis step smoothing 
- Stepper bugs fixed
- Support MIXING_EXTRUDER with Linear Advance
- Miscellaneous cleanup
 2018-06-10 16:02:47 -05:00
Scott Lahteine
bbf80440bf Add sanity-check for MOTHERBOARD 2018-06-10 04:03:33 -05:00
Scott Lahteine
2deff0d9b9 Fix/Improve junction deviation 
- Respect axis max acceleration limits instead of forcing a fixed acceleration value.
- The `junction_unit_vec` ensures proper handling of entry and exit speeds even when the axes involved have different limits.
 2018-05-31 20:09:53 -05:00
Scott Lahteine
9713538427 HOTENDS for Switching Nozzle with Switching Extruder 2018-05-29 11:05:52 -05:00
Scott Lahteine
0ca9db7051 Correct HOTENDS for SWITCHING_EXTRUDER 2018-05-27 23:22:48 -05:00
Scott Lahteine
1b200f3312 Sanity check SWITCHING_EXTRUDER with SINGLENOZZLE 2018-05-26 23:26:23 -05:00
Scott Lahteine
931ab4ec40 Rename Junction Deviation options 2018-05-26 18:33:51 -05:00
Scott Lahteine
aaaf09bda2 BEZIER_JERK_CONTROL => S_CURVE_ACCELERATION 2018-05-26 18:33:51 -05:00
Scott Lahteine
cf7d5a642a
Fix manual moves for switching tools (#10868) 2018-05-26 18:30:53 -05:00
Scott Lahteine
4118199ddd Tweaks to core headers 2018-05-21 20:32:18 -05:00
Bob Kuhn
d557c84a71 [2.0.x] Error for FAST_PWM_FAN with 32 bit CPU (#10798) 2018-05-20 11:37:55 -05:00
Scott Lahteine
83d42f33e1 Add HAS_HOTEND_OFFSET_Z conditional 2018-05-19 17:05:15 -05:00
GMagician
3c76bda2d8 Fix switching extruder 
`DONT_SWITCH` got lost along the way. Replace it with `DO_SWITCH_EXTRUDER` and adjust the code.
 2018-05-19 17:05:15 -05:00
Jiri Jaburek
43ddb29f9e Add FAN_MAX_PWM for M106-controlled fans 2018-05-15 21:18:46 -05:00
Scott Lahteine
b7dfc79988
Disable SERIAL_PORT_2 by default and sanity-check it (#10748) 2018-05-14 21:38:24 -05:00
Scott Lahteine
99ecdf59af Smarter MIN, MAX, ABS macros 
Use macros that explicitly avoid double-evaluation and can be used for any datatype, replacing `min`, `max`, `abs`, `fabs`, `labs`, and `FABS`.

Co-Authored-By: ejtagle <ejtagle@hotmail.com>
 2018-05-13 04:52:56 -05:00
Scott Lahteine
a1062eec5b
Better handling of DELAY_NS and DELAY_US (#10716) 
Co-Authored-By: ejtagle <ejtagle@hotmail.com>
 2018-05-12 08:34:04 -05:00
Scott Lahteine
325bbbc8c2
[2.0.x] Enable AD595 and AD8495 in concert (#10693) 
* Allow both AD595 and AD8495 in concert
* General temperature code tweaks
 2018-05-11 01:01:51 -05:00
Scott Lahteine
19f189b4e5
Add UBL support for G2/G3 and G5 (#10648) 2018-05-08 11:10:45 -05:00
Giuliano
4e16e699c1 Fix sanity checks for dual axes (#10633) 2018-05-07 03:34:26 -05:00
Scott Lahteine
e978e6e782
[2.0.x] Arrange LCD options by type (#10630) 2018-05-06 19:16:55 -05:00
Scott Lahteine
8c5bc77fb9 Fix the sanity-check for config versions 2018-05-06 09:37:00 -05:00
Scott Lahteine
81b632c255 Additional temp-oriented improvements 2018-05-02 08:43:22 -05:00
nightdemonx
e911635fb1 Add thermocouple with AD8495 support 2018-05-02 08:43:16 -05:00
Scott Lahteine
b7e938a9fb LCD_BED_LEVELING enables a sub-menu for ABL 2018-05-01 07:13:56 -05:00
Scott Lahteine
05c33833e7
[2.0.x] Add NO_LCD_MENUS option (#10582) 2018-04-30 21:16:31 -05:00
Scott Lahteine
616651ff23 Add sanity check for LED_CONTROL_MENU 
Addressing #10569
 2018-04-29 18:34:57 -05:00
Scott Lahteine
f790b4bc0a Reorganize some conditionals 2018-04-27 02:23:11 -05:00
Scott Lahteine
df6bc812b5 Fix disable of Z_HOMING_SENSITIVITY for HOMING_Z_WITH_PROBE 
As pointed out in #10532
 2018-04-27 02:23:10 -05:00
Scott Lahteine
299c4fed42 Undefine PIDTEMPBED without a bed heater 2018-04-26 01:30:10 -05:00
Scott Lahteine
cb46cb8480
Add HAS_HEATED_BED conditional (#10495) 2018-04-23 17:13:01 -05:00
Scott Lahteine
9e07df5c1b
Extra options for LEVEL_BED_CORNERS (#10483) 2018-04-22 02:50:48 -05:00
Scott Lahteine
11ab017dd0 Creality3D Power-Loss Recovery 2018-04-21 21:56:50 -05:00
Scott Lahteine
a0dac95d25
Merge pull request #10460 from thinkyhead/bf2_trigorilla_14 
[2.0.x] Split TRIGORILLA into 1.3 and 1.4
 2018-04-20 18:25:40 -05:00
Scott Lahteine
f0cbf3d432 Correction to sanity check 2018-04-20 18:16:27 -05:00
Scott Lahteine
80e29492c6 TRIGORILLA => TRIGORILLA_13 2018-04-20 16:12:25 -05:00
Marcio Teixeira
5cc7916e69 Add G29_RETRY_AND_RECOVER feature 
- Add an option to retry G29, optionally executing a G-code procedure after each failed probe.
 2018-04-19 19:45:53 -05:00
Scott Lahteine
4f184ba5da
[2.0.x] Add BOARD_MKS_BASE_15 with digital micro-stepping (#10454) 
* Add BOARD_MKS_BASE_15 with digital micro-stepping
* Rename MKS_13 to MKS_GEN_13
 2018-04-18 22:58:43 -05:00
Scott Lahteine
39c6f65ce7 Ignore LCD_BED_LEVELING with UBL 2018-04-17 15:57:44 -05:00
Chris Pepper
c9aed73987 Fix missed includes from HAL macro patch (#10416) 2018-04-15 18:27:34 -05:00
Chris Pepper
cc6d41e1d3 Use a macro for HAL header redirection (#10380) 2018-04-12 20:25:08 -05:00
Luc Van Daele
12785583d0 [2.0.x] G33 MIN_STEPS_PER_SEGMENT (#10386) 2018-04-12 20:22:29 -05:00
Yunhui Fu
c96412a78f [2.0.x] UTF-8 language translation support (#10213) 2018-04-12 20:14:01 -05:00
Eduardo José Tagle
57a899a412 [2.0.x] 6th-order jerk-controlled motion planning in real-time for AVR (#10373) 2018-04-11 18:13:42 -05:00
Sean
2d9b0a66fe Add Filament Change accelerations 2018-04-09 23:57:27 -05:00
Scott Lahteine
8b8ad14178 Add Z_PROBE_LOW_POINT to prevent damage 2018-04-09 17:23:03 -05:00
Scott Lahteine
e02fc4f1d6 Better RESTORE_LEVELING_AFTER_G28 sanity-check 
As suggested by @GMagician
 2018-04-08 03:24:15 -05:00
etagle
a29adde5c0 Implement BEZIER_JERK_CONTROL 
Enable 6th-order jerk-controlled motion planning in real-time.
Only for 32bit MCUs. (AVR simply does not have enough processing power for this!)
 2018-04-07 21:03:28 -05:00
Lenbok
0e8242180d Chamber temperature monitoring and auto fan control. 
This is an initial cut for feedback, updated for 2.0.x.

Chamber temperature is currently reported along with hot end and bed
temperatures to serial. The format is just like that used for hot end
and bed temperatures, but using 'C' prefix. As there is no heater,
target is always 0. Is this appropriate, is there a better way to report
chamber temperatures?

Chamber temperatures are not reported on the LCD in any way.

When auto chamber fan is enabled, it currently just uses the same
temperature threshold as the other auto controlled fans.

As the chamber temperature is not connected to any heater, it doesn't
undergo mintemp/maxtemp monitoring. This would need to change in the
future if chamber heating became a feature.
 2018-04-06 23:09:06 -05:00
Marcio Teixeira
75037493fa Default active low for TMC2130 DIAG1 (#10294) 
- Added sanity check to inform users to set the endstop to inverting
  when using SENSORLESS_HOMING
 2018-04-06 19:48:46 -05:00
Karl Andersson
7cbbc2af7a [2.0.x] Optional heater signal inversion (#10260) 2018-04-02 19:37:41 -05:00
Scott Lahteine
adcb87f0db Z Endstop Servo => Z Probe Servo 2018-04-01 23:54:21 -05:00
Scott Lahteine
49f384a2ab Note about MKS_MINI_12864 in sanitycheck 2018-03-31 22:52:23 -05:00
Scott Lahteine
f6d13e2295 Allow Z_SAFE_HOMING sanity checks to handle floats 2018-03-31 19:01:56 -05:00
Scott Lahteine
1be955e52a Alert users about low Z jerk values 2018-03-28 23:08:33 -05:00
Scott Lahteine
a891af2f7a Enforce minimum TMC2130 / TMC2208 libs 2018-03-24 15:57:22 -04:00
Bob-the-Kuhn
433e984d1f move comment to fix compile error 2018-03-24 13:44:54 -05:00
Bob-the-Kuhn
b756a15aba another needs to be deleted 2018-03-24 10:22:03 -05:00
Bob-the-Kuhn
50c81ebe0d remove check that always fails 2018-03-24 09:36:50 -05:00
Scott Lahteine
3ac135cef3 Enforce minimum TMC2130 / TMC2208 libs 2018-03-23 18:05:23 -04:00
Eduardo José Tagle
97e8a6ebd9 Various fixes for DUE... (#10152) 
- Watchdog reset during SD Card initialization.
- Move `DebugMonitor` to `DebugMonitor_Due.cpp`.
- Since the watchdog is enabled on boot do extra resets during init.
- Have `thermalManager` do watchdog reset before its ISR starts to prevent reset.
- Ensure that timers are stopped before reprogramming them to address tone issues.
- Improve SAM3XE reset when reflashed through the native port.
 2018-03-21 19:04:45 -05:00
Scott Lahteine
987597532c For MK2_MULTIPLEXER undef DISABLE_INACTIVE_EXTRUDER 
Fix #10098
 2018-03-21 04:34:50 -05:00
Scott Lahteine
dd2949922b Consolidate 3-point leveling point options 2018-03-19 04:12:20 -05:00
Scott Lahteine
1d22609473 MIN_PROBE_EDGE replaces DELTA_PROBEABLE_RADIUS 2018-03-19 04:11:46 -05:00
Scott Lahteine
d603e655d3 Fix SWITCHING_EXTRUDER manual movement 2018-03-16 03:22:56 -05:00
Scott Lahteine
5f77816772 Reduce size of "only one" sanity checks 2018-03-16 02:43:02 -05:00
Scott Lahteine
e7570f3195 Improve TMC config organization, naming 2018-03-14 00:18:41 -05:00
Scott Lahteine
14c03cb6f4
[2.0.x] Make MIN_PROBE_EDGE a general option (for electronic probes) (#10069) 
Some probes don't work near the edges of the bed. This change promotes MIN_PROBE_EDGE to a general setting that applies to all probing functions.
 2018-03-13 01:15:22 -05:00
Scott Lahteine
28f1276286
[2.0.x] Add Z_AFTER_PROBING option (#10058) 
Some "fix-mounted" probes need manual stowing. And after probing some may prefer to raise or lower the nozzle. This restores an old option but tailors it to allow raise or lower as preferred.
 2018-03-11 13:07:55 -05:00
Bob-the-Kuhn
0d8c15c01f restore PR 9661 files & V1 fix 2018-03-10 22:46:32 -06:00
Bob-the-Kuhn
bf59a4a6df
Revert "[2.0.x] DUE compatibility with shared SPI LCDs, USB mass storage, add pin defs & update examples\MakerParts\Configuration.h" 2018-03-10 17:22:20 -06:00
Bob-the-Kuhn
914bb80bde removed SDSS init 
added device & comm drivers for shared SPI LCDs

mistyped some updates in ultralcd_impl_DOGM.h

remove unwanted changes in onfiguration.h

still can't type

Update HAL_LCD_class_defines.h

include USB mass storage & misc
 2018-03-09 23:06:11 -06:00
Scott Lahteine
eb212ae073 Add suspend_auto_report flag to suppress auto-report 2018-03-07 01:57:09 -06:00
Scott Lahteine
ffbf63e6af Add HAS_TEMP_SENSOR conditional 2018-03-07 01:53:50 -06:00
Scott Lahteine
6d7f4f84e2
Add board MKS_BASE_HEROIC (#9926) 
Followup to #9008

- Don't define micro-stepping pins for boards that lack them.
- Allow setting of 128 microsteps with `M350`.
 2018-03-03 23:14:52 -06:00
Scott Lahteine
c37b3f995a Sanity-check some graphical LCD-only options 2018-03-03 20:31:59 -06:00
Bob-the-Kuhn
c1f4112bdc [2.0.x] Add 1284 support & misc. bug fixes (#9864) 2018-03-01 03:07:39 -06:00
Scott Lahteine
118899357d
Add sanity checks to Linear Advance 1.5 (#9873) 2018-03-01 02:10:43 -06:00
Scott Lahteine
a446433c87
Fix SENSORLESS_HOMING for Core Kinematics (#9868) 2018-03-01 01:37:31 -06:00
Scott Lahteine
8c03ce4d80 Fix Z safe homing sanity check for no probe 
Fix #9851
 2018-02-28 05:28:35 -06:00
Scott Lahteine
3f89bbeab5 Drop a conditional only used once 2018-02-24 16:35:31 -06:00
Scott Lahteine
b2cf253a13 Add RESTORE_LEVELING_AFTER_G28 option 2018-02-23 13:38:54 -06:00
Scott Lahteine
2bd252b501
[2.0.x] LIN_ADVANCE v1.5 (#9712) 2018-02-23 00:53:29 -06:00
Scott Lahteine
7d8c6b3f3c
Add 20x4 option for Sainsmart LCD (#9740) 2018-02-21 00:46:25 -06:00
Scott Lahteine
c4ec01d59b Conditionals for SWITCHING_EXTRUDER 
In reference to #5367. SWITCHING_EXTRUDER was not fully implemented for EXTRUDERS > 2.
 2018-02-19 10:59:47 -06:00
Studiodyne
d3ca82d8c2 Support for multiple filament runout sensors 2018-02-19 07:02:50 -06:00
Scott Lahteine
ca55f2927a
Pulldown pin mode support (#9701) 
Implemented for LPC1768.
 2018-02-18 19:26:23 -06:00
Kevin
9019ea0fce Option to force X or Y to home first when homing the other axis 2018-02-18 01:11:41 -06:00
Scott Lahteine
f6cc89ec7c LCD_PROGRESS_BAR w/out SDSUPPORT for character LCD 2018-02-17 08:17:22 -06:00
Roxy-3D
3d74ff3c87
Cartesian UBL systems should not use SEGMENT_LEVELED_MOVES 
There is significant downside to breaking up the long line segments on UBL Cartesian machines.   It adds a lot of extra computation but worse...  It cuts out all of UBL's off mesh Z-Height correction checks.    There have been a large number of people complaining about the nozzle going to infinity or crashing into the bed lately.   They are being caused by
```
void unified_bed_leveling::line_to_destination_cartesian()
```
not watching over the segments being queued up for movement.
 2018-02-14 14:16:12 -06:00
Scott Lahteine
5dc04c5201 Fix #9361 2018-02-14 07:48:20 -06:00
Scott Lahteine
8e0c107545
Have Kossel Pro use Z_MIN_PROBE_ENDSTOP (#9586) 2018-02-11 01:41:40 -06:00
Scott Lahteine
f64d300cfd
Sanity check SERIAL_PORT 
Addressing #7400
 2018-02-09 00:44:15 -06:00
Thomas Moore
1541224a81 Enable Z axis and delta sensorless homing (#9516) 2018-02-08 04:20:44 -06:00
Scott Lahteine
b2f8b4ada5
I2C position encoders update (#9533) 
Updating I2C position encoders to enable babystepping and Babystep XY when using the ecm microstep correction method. Also changed default method to ECM microstep.
 2018-02-08 03:57:11 -06:00
Scott Lahteine
704d33c374 Special override of LCD_WIDTH 2018-02-08 01:30:56 -06:00
Scott Lahteine
16739264d3 Add UltiController v2.1 support 
Add compatibility with the original screen bord from Ultimaker 2 printer (UltiController v2.1 with the PG-2864ALBP I2C display)
 2018-02-05 22:30:03 -06:00
GMagician
f27c89980a [2.0.x] Simplify bltouch configuration (#9488) 2018-02-05 14:38:09 -06:00
Scott Lahteine
3a1225e438 Sanity check SENSORLESS_HOMING 2018-02-04 18:52:44 -06:00
Scott Lahteine
db031d5d76 Add missing SoftwareSerial begin for TMC2208 
Based on #9299
 2018-01-22 10:43:24 -06:00
Thomas Moore
3db35ba9be [2.0.x] Fix change filament for delta machines (#9295) 2018-01-22 10:21:42 -06:00
Scott Lahteine
2ebf52e57d Fix Skew Correction pre-calculation overflow error 2018-01-22 08:20:21 -06:00
Scott Lahteine
582d073de1 Patch up digital microstepping and SPI CS pins 2018-01-22 01:27:11 -06:00
Scott Lahteine
8190fdb260
[2.0.x] Option to use Neopixel as case light (#9270) 
* Add option to use Neopixel as case light

* Apply CASE_LIGHT_USE_NEOPIXEL to example configs
 2018-01-20 16:58:41 -06:00
Scott Lahteine
4bc4351250
Date refresh 2018-01-20 09:17:57 -06:00
Scott Lahteine
f2ea8a0529
Merge pull request #9197 from p3p/pr_bf2_operation_freemem 
[2.0.x] LPC1768: Free up some RAM
 2018-01-19 22:35:45 -06:00
Roxy-3D
9d0cf02fef
Correct mesh size calculations 2018-01-17 09:36:12 -06:00
Roxy-3D
acb1e31374
Fix UBL Mesh Size regression 2018-01-16 17:58:15 -06:00
Christopher Pepper
6f1bf5d212 LPC1768: Config: default to SDSORT_LIMIT = 64 instead of 256 2018-01-15 22:02:21 +00:00
Scott Lahteine
6a043eee55 Various updates for TMC support 2018-01-10 23:04:48 -06:00
Thomas Moore
f7efac57b7 Multi-host support 2018-01-10 00:14:47 -06:00
Scott Lahteine
a94104dbb5
Merge pull request #9113 from teemuatlut/TMC_followup 
[2.0.x]TMC followup
 2018-01-09 18:46:35 -06:00
Dave Johnson
554e577676 SERIAL_STATS_* features not supported on USBCON targets (#9127) 2018-01-09 18:42:55 -06:00
teemuatlut
9d923c6c03 Fix TMC gcode commands 2018-01-08 18:45:05 +02:00
Scott Lahteine
1c41de16d4 Trailing whitespace clean 2018-01-05 10:11:31 -06:00
Scott Lahteine
7541316bb4 Add M701/M702 Filament Load/Unload, M603 2018-01-04 15:07:37 -06:00
Thomas Moore
f0a8a1a853 [2.0.x] Use NOZZLE_PARK_FEATURE for ADVANCED_PAUSE_FEATURE (#8866) 
* Use NOZZLE_PARK_FEATURE for ADVANCED_PAUSE_FEATURE
 2017-12-25 01:38:06 -06:00
Even
ea1a8d1223 add original RADDS LCD + Controller 
adds setup for the original Radds Display+Controller+SD Card Reader PCB
http://doku.radds.org/dokumentation/lcd-display/
 2017-12-24 19:00:23 -06:00
Scott Lahteine
5bc2acc072 Restore position_float to fix LIN_ADVANCE 2017-12-21 16:45:46 -06:00
Scott Lahteine
fdc5e72720 A single setting to validate filament width 2017-12-19 21:33:25 -06:00
Scott Lahteine
933f76fda3 Option to disable all volumetric extrusion 2017-12-19 19:51:25 -06:00
Scott Lahteine
fc9ee1a4de Fix up serial sanity check 2017-12-19 19:11:43 -06:00
Scott Lahteine
957bbab57f Update inc files for parity with 1.1.x 2017-12-16 20:20:06 -06:00
Dan Delaney
b055d8c39c [2.0.x] Adding support for using the MKS_12864OLED with the SSD1306 controller (#8814) 
* Adding support for using the MKS_12864OLED with the SSD1306 controller

* Update comment for correct controller type
 2017-12-16 18:47:04 -06:00
Scott Lahteine
15d05748df Adding support for the Tronxy and Zonestar LCD 2017-12-15 19:13:52 -06:00
teemuatlut
0cd1e91056 [2.0.x] TMC driver update (#8769) 2017-12-15 15:03:14 -06:00
Scott Lahteine
a71d2f3f40 UBL_DELTA => UBL_SEGMENTED 2017-12-11 00:27:06 -06:00
Scott Lahteine
ae663a4198 PROBE_DOUBLE_TOUCH => MULTIPLE_PROBING 2017-12-07 16:44:13 -06:00
Scott Lahteine
f206b81cf7 Sanity check skew+UBL 2017-12-06 22:56:58 -06:00
Scott Lahteine
2fde60da12 Changes for parity with 1.1.x 2017-12-06 21:50:54 -06:00
Richard Wackerbarth
c1184552ac Change K1 to required option PID_K1 2017-12-05 19:59:59 -06:00
Unknown
91b63f6d69 SERIAL_XON_XOFF not supported on USB-native AVR devices 
User could enable SERIAL_XON_XOFF on USB-native devices and it would not be enabled without warning, but M115 would report the capability as available.
 2017-12-04 03:57:01 -08:00
Scott Lahteine
f9327534f8
Merge pull request #8634 from fiveangle/bf2_report_xonxoff 
[2.0.x] Report SERIAL_XON_XOFF in M115
 2017-12-03 02:18:50 -06:00
Scott Lahteine
24437de591 Use custom segment length for UBL Cartesian 2017-12-03 00:10:54 -06:00
Unknown
4c5ffd2349 [2.0.x] Report SERIAL_XON_XOFF in M115 
-Report SERIAL_XON_XOFF in Extended Capabilites M115 report for hosts
-Remove outdated 256 size limitation from comments on RX_BUFFER_SIZE defines
-Update error message conditions
 2017-12-02 21:08:06 -08:00
Scott Lahteine
0154e3480c New feature: BED_SKEW_CORRECTION 2017-12-01 19:39:49 -06:00
Scott Lahteine
8f90642eea LED_CONTROL_MENU config changes 2017-11-29 21:02:56 -06:00
Scott Lahteine
ef2531558c Add an option to segment leveled moves 2017-11-29 16:57:30 -06:00
Scott Lahteine
94cb412e45 Allow override of probe bounds 2017-11-26 20:55:27 -06:00
Scott Lahteine
7be4857ab9 Tweak BLOCK_BUFFER_SIZE description 2017-11-26 17:36:40 -06:00
Scott Lahteine
d06e29846d Loosen HAS_BED_PROBE definition 2017-11-25 20:11:21 -06:00
Scott Lahteine
7576ad7fc2
Merge pull request #8554 from tcm0116/2.0.x-cleanup 
[2.0.x] Fix for #8525 and other cleanup
 2017-11-25 18:19:54 -06:00
Thomas Moore
2ea779e560 Allow bed probe sanity checks to run 2017-11-24 21:59:01 -06:00
Scott Lahteine
d24b1190bd Don't use Z_MIN_PROBE_ENDSTOP on DELTA 2017-11-24 18:24:22 -06:00
oliver
92a0dc552a MK2_MULTIPLEXER does not require E2/E3 stepper pins 2017-11-24 23:56:39 +01:00
Scott Lahteine
5926c9c97b Followup for MESH_EDIT_GFX_OVERLAY 2017-11-24 15:53:25 -06:00
Scott Lahteine
c6b0c104bb Adapt G26 to work for all meshes 2017-11-23 22:31:37 -06:00
Scott Lahteine
5ce7f23afa Config option G26_MESH_VALIDATION for all meshes 2017-11-23 21:43:23 -06:00
Scott Lahteine
3066655727 Try port*100+pin, fix config dependency 2017-11-20 13:58:23 -06:00
Scott Lahteine
b9327a4d16 Misc. general cleanup 2017-11-19 15:43:39 -06:00
Scott Lahteine
1d4571b88d Dependency adjustments 2017-11-19 15:43:38 -06:00
Roxy-3D
9729528d13
Update UBL's Delta Probable locations 
This is a non-intuitive change.   @oldmcg says in this post https://github.com/MarlinFirmware/Marlin/issues/7572#issuecomment-340641207 that using DELTA_PRINTABLE_RADIUS is better than DELTA_PROBABLE_RADIUS for setting the probe limits.   This is because the automatic probe code checks all locations for being reachable by the probe prior to doing the probe.
 2017-11-17 16:44:57 -06:00
Dave Johnson
c009a990e4 [2.0.x] Fix some 8-bit Teensyduino compile warnings (#8385) 
* Fix some 8-bit Teensyduino compile warnings

-Override Teensyduino legacy NOT_A_PIN 127 define
-some fixups for Printrboard_RevF pins

* Proper cleanup of Printrboard Rev.F pins

* Apply LCD fixes to Printrboard v1
 2017-11-13 01:07:59 -06:00
Scott Lahteine
c66696c507
Merge pull request #8344 from tcm0116/2.0.x-delta_height 
[2.0.x] Add delta_height variable in lieu of using home_offset
 2017-11-09 01:21:53 -06:00
Scott Lahteine
0cfb936dd1 Clarify some motion code 2017-11-08 22:15:55 -06:00
Thomas Moore
f34c3597dc Add delta_height variable in lieu of using home_offset 2017-11-08 22:10:08 -06:00
Scott Lahteine
82f45c3e6a Patch G33 misuse of PROBE_MANUALLY 2017-11-08 00:36:06 -06:00
Scott Lahteine
1b40e9c464 Implement CNC_COORDINATE_SYSTEMS 2017-11-04 22:28:46 -05:00
Scott Lahteine
ca7d36d9ed RAMPS pins for ANET_KEYPAD_LCD 2017-11-04 21:22:53 -05:00
Colten Edwards
e0a6ee8da5 [2.0] Fix up G33, LPC1768 + SDCARD_SORT_ALPHA (#8250) 
* Update Conditionals_post.h

* Add a cast to round() to convert to a unsigned int

Add's a cast to round() so that it will compile properly. round() returns a float which must be cast to a integer for the following % operation. Use a unsigned int as a negative index to an array is wrong. Should never be more than 255 points allowing us to use a 8 bit cast.

* Update G33.cpp
 2017-11-04 18:04:18 -05:00
Scott Lahteine
93ba72ea83 Add SERIAL_PORT -1, set on SBASE, STM32F103RET6 2017-11-03 15:22:45 -05:00
android444
9cc1d8e312 [2.0.x] Support for SilverGate Board 2017-10-31 15:27:26 -05:00
Scott Lahteine
571ced712d Add SDCARD_SORT_ALPHA options for LPC1768 2017-10-31 14:05:40 -05:00
Scott Lahteine
9f89b5d876 Fix for MAX_VFAT_ENTRIES sanity check 2017-10-30 15:11:47 -05:00
Scott Lahteine
2cdde08339 Apply items specified in code review 
Followup to #8122
 2017-10-30 15:03:07 -05:00
Scott Lahteine
723f2a77f6 Implement support for Dual X and Y endstops 2017-10-29 18:56:04 -05:00
Scott Lahteine
bd78ca0ee3 Add M290 Babystepping 2017-10-26 20:44:43 -05:00
Scott Lahteine
3ac581eac9 Neopixel changes for parity with 1.1.x 2017-10-25 18:40:04 -05:00
Scott Lahteine
f65fc7ffab Merge pull request #8044 from thinkyhead/bf2_mesh_consolidate 
[2.0.x] Simplify mesh bounds config
 2017-10-24 18:56:43 -05:00
Thomas Moore
51fafccc16 [2.0.x] Enable hardware serial ports on LPC1768 (#8004) 
* Enable hardware serial ports on LPC1768

* Fix compilation errors with other HALs

* FIx order of includes in LPC1768 HAL main.cpp

* Add support for RX_BUFFER_SIZE and TX_BUFFER_SIZE options in Configuration_adv.h
 2017-10-24 17:28:33 -05:00
Scott Lahteine
580b6e9089 Apply physical limits to mesh bounds 2017-10-24 16:54:07 -05:00
Scott Lahteine
4e2baeb3e1 Update indentation, file-wrapping for Marlin 2.0.x 2017-10-24 16:54:06 -05:00
Scott Lahteine
60af705e6d Relocate SPI.h to the HAL folder 2017-10-24 16:54:06 -05:00
cdedwards
6296ab2173 Add GFX overlay to UBL mesh edit (#8038) 
* Add GFX overlay to UBL mesh edit

Fixed misplaced HAS_TEMP_BED in dogm_bitmaps.h

rename _lcd_babystep_zoffset_overlay to _lcd_zoffset_overlay_gfx and move it out of BABYSTEP_ZPROBE_OFFSET to we can use it for over things. Add this function into UBL mesh edit screen.

update all Configuration.h to add ENABLE_MESH_EDIT_GFX_OVERLAY

* Add Sanity to UBL  insanity

Need to check for DOGLCD  otherwise error out.
 2017-10-24 14:14:03 -05:00
Scott Lahteine
3d2b2eb1ca Prevent SDCARD_SORT_ALPHA from exploding 2017-10-20 19:13:21 -05:00
Scott Lahteine
9e5cbf0198 BQ should set this in its config, and does 2017-10-18 22:56:03 -05:00
Scott Lahteine
348e5e3109 Simplify Cartesian probing boundaries 
Followup to #8012
 2017-10-18 17:14:32 -05:00
Jeffrey Li
eeb4611606 Add proper support for the AZSMZ 12864 LCD on a SMART RAMPS 2017-10-16 00:33:07 -07:00
Scott Lahteine
e587f0893c Define AVR_ATmega2560_FAMILY_PLUS_70 in Conditionals 2017-10-14 19:05:32 -05:00
Jeff Eberl
b206f70693 Split the software endstop capability by axis. 2017-10-14 18:44:20 -05:00
Scott Lahteine
58abc66c1d Tweak bed leveling conditionals 2017-10-14 02:18:31 -05:00
Slawomir Ciunczyk
a11e6a1022 Different NEOPIXEL types 
Same as #7728 but for 2.0.x,
Lot of cleanup and remove references in whole code to other "LED files" than leds.h. Now will be much easier to add next drivers/libraries. e.g. FastLED. But bad news, currently FastLED is suporting only RGB devices (no RGBW)
 2017-10-10 02:17:36 -05:00
Scott Lahteine
b30b55307c Merge pull request #7909 from thinkyhead/bf2_goodbye_legacy_advance 
[2.0.x] Remove legacy ADVANCE feature
 2017-10-10 00:31:18 -05:00
Scott Lahteine
442669d23c Allow UBL to build without a probe 2017-10-09 18:57:41 -05:00
Scott Lahteine
560d366b80 Move VIKI SCK/MOSI pins fix to Conditionals_POST.h 2017-10-09 16:13:49 -05:00
Scott Lahteine
e9bcb9d048 Add 4 new LCD displays 2017-10-09 15:58:02 -05:00
Scott Lahteine
03f4891fb9 Remove legacy ADVANCE feature 2017-10-09 04:25:18 -05:00
Scott Lahteine
8315a8a716 Apply fixes for DUE 
Alternative to #7882. If F_CPU is greater than 1000 it can be evenly divided by 8. Over 10000, 16; over 100000, 32; over 1 million, 64; etc.
 2017-10-07 14:31:18 -05:00
Scott Lahteine
7fb3343bda [2.0.x] Addressing #7612 
Change "extruder" to HOTEND in sanity error messages
 2017-10-07 02:27:26 -05:00
Scott Lahteine
2aa22c5a5e Merge pull request #7874 from thinkyhead/bf2_anet_encoder_pulses 
[2.0.x] Fixing ANET encoder pulses
 2017-10-07 01:21:23 -05:00
Scott Lahteine
f99d1dedae Fixing #7833 
Derived from #7873
 2017-10-07 00:10:05 -05:00
Scott Lahteine
ef90b49fff Remove extra NEWPANEL settings in Conditionals_LCD.h 2017-10-06 23:56:58 -05:00
Scott Lahteine
965b0ab53e Spacing adjustments 2017-10-01 21:58:50 -05:00
Christopher Pepper
bea3ec2724 M355 S0, S1 fixes & faster LCD, SD card 
fix Travis error
 2017-09-27 19:26:00 -05:00
Scott Lahteine
fdf1b8a7b8 Fix sanity check for LCD_FOR_MELZI 
Comes from #7760
 2017-09-27 03:04:19 -05:00
Scott Lahteine
ce1638e32f Add Babystep Z graphic overlay 
See PR #7593
 2017-09-27 01:25:05 -05:00
Scott Lahteine
7a29f802d0 Fix ENCODER_PULSES_PER_STEP for G3D_PANEL 2017-09-26 23:43:05 -05:00
Dave Johnson
f58ba3a64e Improve AVR arch detection 
Replace ARDUINO_ARCH_AVR with __AVR__ to better detect architecture for non-Arduino dev environments.  Resolves compile failure in PIO for 8-bit Teensduino targets

More info:
https://forum.pjrc.com/threads/33234-Using-Teensyduino-Selecting-Teensy-3-2-3-1-board-has-incorrect-platform-define
http://www.atmel.com/webdoc/avrlibcreferencemanual/using_tools_1using_avr_gcc_mach_opt.html
 2017-09-23 21:36:40 -07:00
Scott Lahteine
f37ed314e0 Friendly layout for Arduino IDE 2017-09-21 16:27:13 -05:00
Scott Lahteine
3d8a0ab4b2 Module updates 2017-09-21 16:26:42 -05:00
Scott Lahteine
34101224c4 Inc updates 2017-09-21 16:26:41 -05:00
Scott Lahteine
5be07b5db2 Move 'inc' files 2017-09-07 07:42:55 -05:00