🧑‍💻 IS_ULTRA_LCD => HAS_WIRED_LCD

This commit is contained in:
Scott Lahteine 2022-04-21 07:16:52 -05:00 committed by Scott Lahteine
parent 2f3960904e
commit f6f31434b8
10 changed files with 20 additions and 21 deletions

View File

@ -41,13 +41,13 @@
*
* DOGLCD : Run a Graphical LCD through U8GLib (with MarlinUI)
* IS_ULTIPANEL : Define LCD_PINS_D5/6/7 for direct-connected "Ultipanel" LCDs
* IS_ULTRA_LCD : Ultra LCD, not necessarily Ultipanel.
* HAS_WIRED_LCD : Ultra LCD, not necessarily Ultipanel.
* IS_RRD_SC : Common RRD Smart Controller digital interface pins
* IS_RRD_FG_SC : Common RRD Full Graphical Smart Controller digital interface pins
* IS_U8GLIB_ST7920 : Most common DOGM display SPI interface, supporting a "lightweight" display mode.
* U8GLIB_SH1106 : SH1106 OLED with I2C interface via U8GLib
* IS_U8GLIB_SSD1306 : SSD1306 OLED with I2C interface via U8GLib (U8GLIB_SSD1306)
* U8GLIB_SSD1309 : SSD1309 OLED with I2C interface via U8GLib (HAS_U8GLIB_I2C_OLED, IS_ULTRA_LCD, DOGLCD)
* U8GLIB_SSD1309 : SSD1309 OLED with I2C interface via U8GLib (HAS_U8GLIB_I2C_OLED, HAS_WIRED_LCD, DOGLCD)
* IS_U8GLIB_ST7565_64128N : ST7565 128x64 LCD with SPI interface via U8GLib
* IS_U8GLIB_LM6059_AF : LM6059 with Hardware SPI via U8GLib
*/
@ -287,7 +287,7 @@
// 128x64 I2C OLED LCDs - SSD1306/SSD1309/SH1106
#if ANY(U8GLIB_SSD1306, U8GLIB_SSD1309, U8GLIB_SH1106)
#define HAS_U8GLIB_I2C_OLED 1
#define IS_ULTRA_LCD 1
#define HAS_WIRED_LCD 1
#define DOGLCD
#endif
@ -443,7 +443,7 @@
#endif
#if EITHER(IS_ULTIPANEL, ULTRA_LCD)
#define IS_ULTRA_LCD 1
#define HAS_WIRED_LCD 1
#endif
#if EITHER(IS_ULTIPANEL, REPRAPWORLD_KEYPAD)
@ -502,8 +502,7 @@
#endif
#endif
#if IS_ULTRA_LCD
#define HAS_WIRED_LCD 1
#if HAS_WIRED_LCD
#if ENABLED(DOGLCD)
#define HAS_MARLINUI_U8GLIB 1
#elif IS_TFTGLCD_PANEL

View File

@ -106,7 +106,7 @@
//
#define BEEPER_PIN 33
#if IS_ULTRA_LCD && IS_NEWPANEL
#if HAS_WIRED_LCD && IS_NEWPANEL
#define LCD_PINS_RS 16
#define LCD_PINS_ENABLE 17
@ -122,7 +122,7 @@
#define SD_DETECT_PIN -1 // RAMPS doesn't use this
#endif // IS_ULTRA_LCD && IS_NEWPANEL
#endif // HAS_WIRED_LCD && IS_NEWPANEL
//
// M3/M4/M5 - Spindle/Laser Control

View File

@ -61,7 +61,7 @@
#endif
#endif
#if !(BOTH(IS_ULTRA_LCD, IS_NEWPANEL) && ANY(PANEL_ONE, VIKI2, miniVIKI, WYH_L12864, MINIPANEL, REPRAPWORLD_KEYPAD))
#if !(BOTH(HAS_WIRED_LCD, IS_NEWPANEL) && ANY(PANEL_ONE, VIKI2, miniVIKI, WYH_L12864, MINIPANEL, REPRAPWORLD_KEYPAD))
#define HAS_FREE_AUX2_PINS 1
#endif

View File

@ -111,7 +111,7 @@
#define SPINDLE_LASER_PWM_PIN 46 // Hardware PWM
#define SPINDLE_LASER_ENA_PIN 62 // Pullup!
#define SPINDLE_DIR_PIN 48
#elif !BOTH(IS_ULTRA_LCD, IS_NEWPANEL) // Use expansion header if no LCD in use
#elif !BOTH(HAS_WIRED_LCD, IS_NEWPANEL) // Use expansion header if no LCD in use
#define SPINDLE_LASER_ENA_PIN 16 // Pullup or pulldown!
#define SPINDLE_DIR_PIN 17
#if !NUM_SERVOS // Use servo connector if possible
@ -135,7 +135,7 @@
//
// LCD / Controller
//
#if IS_ULTRA_LCD && IS_NEWPANEL
#if HAS_WIRED_LCD && IS_NEWPANEL
#undef BEEPER_PIN
// TODO: Remap EXP1/2 based on adapter
@ -164,7 +164,7 @@
#define BEEPER_PIN 33
#endif // IS_ULTRA_LCD && IS_NEWPANEL
#endif // HAS_WIRED_LCD && IS_NEWPANEL
#if IS_U8GLIB_ST7920
#define BOARD_ST7920_DELAY_1 0

View File

@ -49,7 +49,7 @@
//
// LCD / Controller
//
#if IS_ULTRA_LCD && IS_NEWPANEL
#if HAS_WIRED_LCD && IS_NEWPANEL
#define SD_DETECT_PIN 6

View File

@ -69,7 +69,7 @@
//
// LCD / Controller
//
#if IS_ULTRA_LCD && IS_NEWPANEL
#if HAS_WIRED_LCD && IS_NEWPANEL
#undef BEEPER_PIN
#undef LCD_PINS_RS

View File

@ -172,7 +172,7 @@
#define LCD_PINS_D6 32
#define LCD_PINS_D7 30
#elif BOTH(BOARD_REV_1_5, IS_ULTRA_LCD)
#elif BOTH(BOARD_REV_1_5, HAS_WIRED_LCD)
#define BEEPER_PIN 18

View File

@ -135,7 +135,7 @@
#define LCD_BACKLIGHT_PIN 17 // LCD backlight LED
#endif
#if !HAS_CUTTER && ENABLED(SANGUINOLOLU_V_1_2) && !BOTH(IS_ULTRA_LCD, IS_NEWPANEL) // try to use IO Header
#if !HAS_CUTTER && ENABLED(SANGUINOLOLU_V_1_2) && !BOTH(HAS_WIRED_LCD, IS_NEWPANEL) // try to use IO Header
#define CASE_LIGHT_PIN 4 // Hardware PWM - see if IO Header is available
#endif
@ -268,7 +268,7 @@
// M3/M4/M5 - Spindle/Laser Control
//
#if HAS_CUTTER
#if !MB(AZTEEG_X1) && ENABLED(SANGUINOLOLU_V_1_2) && !BOTH(IS_ULTRA_LCD, IS_NEWPANEL) // try to use IO Header
#if !MB(AZTEEG_X1) && ENABLED(SANGUINOLOLU_V_1_2) && !BOTH(HAS_WIRED_LCD, IS_NEWPANEL) // try to use IO Header
#define SPINDLE_LASER_ENA_PIN 10 // Pullup or pulldown!
#define SPINDLE_LASER_PWM_PIN 4 // Hardware PWM

View File

@ -121,7 +121,7 @@
//
// LCD / Controller
//
#if IS_ULTRA_LCD && IS_NEWPANEL
#if HAS_WIRED_LCD && IS_NEWPANEL
#define LCD_PINS_RS 9 // E1 JP11-11
#define LCD_PINS_ENABLE 8 // E0 JP11-10
@ -163,7 +163,7 @@
#endif
#endif // IS_ULTRA_LCD && IS_NEWPANEL
#endif // HAS_WIRED_LCD && IS_NEWPANEL
#ifndef SDSS
#define SDSS 26 // B6 SDCS

View File

@ -145,7 +145,7 @@
//
// LCD / Controller
//
#if IS_ULTRA_LCD && IS_NEWPANEL
#if HAS_WIRED_LCD && IS_NEWPANEL
#define BEEPER_PIN -1
@ -158,7 +158,7 @@
#define SD_DETECT_PIN -1
#endif // IS_ULTRA_LCD && IS_NEWPANEL
#endif // HAS_WIRED_LCD && IS_NEWPANEL
//
// M3/M4/M5 - Spindle/Laser Control