bissen21/Marlin_Firmware
1
0
Fork 0
Code Issues Pull Requests Projects Releases 4 Wiki Activity

Clarify TMC2209 Sensitivity vs. Others (#15092)

Browse Source
This commit is contained in:
thisiskeithb 2019-08-29 14:57:56 -07:00 committed by Scott Lahteine
parent 3f77d6a551
commit f5a1fabd38
100 changed files with 600 additions and 400 deletions
Show Stats Download Patch File Download Diff File Expand all files Collapse all files

10
Marlin/Configuration_adv.h
View File

@ -1940,10 +1940,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/default/Configuration_adv.h
View File

@ -1940,10 +1940,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/3DFabXYZ/Migbot/Configuration_adv.h
View File

@ -1940,10 +1940,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/ADIMLab/Gantry v1/Configuration_adv.h
View File

@ -1926,10 +1926,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/ADIMLab/Gantry v2/Configuration_adv.h
View File

@ -1940,10 +1940,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/AlephObjects/TAZ4/Configuration_adv.h
View File

@ -1940,10 +1940,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/Alfawise/U20/Configuration_adv.h
View File

@ -1943,10 +1943,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/AliExpress/UM2pExt/Configuration_adv.h
View File

@ -1942,10 +1942,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/Anet/A2/Configuration_adv.h
View File

@ -1940,10 +1940,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/Anet/A2plus/Configuration_adv.h
View File

@ -1940,10 +1940,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/Anet/A6/Configuration_adv.h
View File

@ -1940,10 +1940,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/Anet/A8/Configuration_adv.h
View File

@ -1940,10 +1940,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/Anet/A8plus/Configuration_adv.h
View File

@ -1940,10 +1940,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/Anet/E16/Configuration_adv.h
View File

@ -1940,10 +1940,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/AnyCubic/i3/Configuration_adv.h
View File

@ -1940,10 +1940,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/ArmEd/Configuration_adv.h
View File

@ -1944,10 +1944,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/BIBO/TouchX/cyclops/Configuration_adv.h
View File

@ -1940,10 +1940,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/BIBO/TouchX/default/Configuration_adv.h
View File

@ -1940,10 +1940,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/BQ/Hephestos/Configuration_adv.h
View File

@ -1940,10 +1940,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/BQ/Hephestos_2/Configuration_adv.h
View File

@ -1948,10 +1948,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/BQ/WITBOX/Configuration_adv.h
View File

@ -1940,10 +1940,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/Cartesio/Configuration_adv.h
View File

@ -1940,10 +1940,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/Creality/CR-10/Configuration_adv.h
View File

@ -1940,10 +1940,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/Creality/CR-10S/Configuration_adv.h
View File

@ -1940,10 +1940,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/Creality/CR-10_5S/Configuration_adv.h
View File

@ -1940,10 +1940,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/Creality/CR-10mini/Configuration_adv.h
View File

@ -1940,10 +1940,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/Creality/CR-20 Pro/Configuration_adv.h
View File

@ -1940,10 +1940,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/Creality/CR-20/Configuration_adv.h
View File

@ -1940,10 +1940,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/Creality/CR-8/Configuration_adv.h
View File

@ -1940,10 +1940,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/Creality/Ender-2/Configuration_adv.h
View File

@ -1940,10 +1940,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/Creality/Ender-3/Configuration_adv.h
View File

@ -1940,10 +1940,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/Creality/Ender-4/Configuration_adv.h
View File

@ -1940,10 +1940,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/Creality/Ender-5/Configuration_adv.h
View File

@ -1940,10 +1940,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/Dagoma/Disco Ultimate/Configuration_adv.h
View File

@ -1940,10 +1940,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/EVNOVO (Artillery)/Sidewinder X1/Configuration_adv.h
View File

@ -1940,10 +1940,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/Einstart-S/Configuration_adv.h
View File

@ -1940,10 +1940,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/FYSETC/AIO_II/Configuration_adv.h
View File

@ -1940,10 +1940,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/FYSETC/Cheetah 1.2/BLTouch/Configuration_adv.h
View File

@ -1940,10 +1940,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/FYSETC/Cheetah 1.2/base/Configuration_adv.h
View File

@ -1939,10 +1939,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/FYSETC/Cheetah/BLTouch/Configuration_adv.h
View File

@ -1939,10 +1939,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/FYSETC/Cheetah/base/Configuration_adv.h
View File

@ -1939,10 +1939,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/FYSETC/F6_13/Configuration_adv.h
View File

@ -1926,10 +1926,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/Felix/Configuration_adv.h
View File

@ -1940,10 +1940,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/FlashForge/CreatorPro/Configuration_adv.h
View File

@ -1939,10 +1939,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/FolgerTech/i3-2020/Configuration_adv.h
View File

@ -1940,10 +1940,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/Formbot/Raptor/Configuration_adv.h
View File

@ -1942,10 +1942,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/Formbot/T_Rex_2+/Configuration_adv.h
View File

@ -1944,10 +1944,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/Formbot/T_Rex_3/Configuration_adv.h
View File

@ -1944,10 +1944,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/Geeetech/A10/Configuration_adv.h
View File

@ -1940,10 +1940,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/Geeetech/A10M/Configuration_adv.h
View File

@ -1940,10 +1940,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/Geeetech/A20M/Configuration_adv.h
View File

@ -1940,10 +1940,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/Geeetech/MeCreator2/Configuration_adv.h
View File

@ -1939,10 +1939,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h
View File

@ -1940,10 +1940,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h
View File

@ -1940,10 +1940,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/HMS434/Configuration_adv.h
View File

@ -1876,10 +1876,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/Infitary/i3-M508/Configuration_adv.h
View File

@ -1940,10 +1940,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/JGAurora/A1/Configuration_adv.h
View File

@ -1945,10 +1945,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/JGAurora/A5/Configuration_adv.h
View File

@ -1940,10 +1940,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/JGAurora/A5S/Configuration_adv.h
View File

@ -1945,10 +1945,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/MakerParts/Configuration_adv.h
View File

@ -1940,10 +1940,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/Malyan/M150/Configuration_adv.h
View File

@ -1940,10 +1940,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/Malyan/M200/Configuration_adv.h
View File

@ -1940,10 +1940,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/Micromake/C1/enhanced/Configuration_adv.h
View File

@ -1940,10 +1940,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/Mks/Robin/Configuration_adv.h
View File

@ -1940,10 +1940,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/Mks/Sbase/Configuration_adv.h
View File

@ -1941,10 +1941,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/RapideLite/RL200/Configuration_adv.h
View File

@ -1940,10 +1940,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/RigidBot/Configuration_adv.h
View File

@ -1940,10 +1940,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/SCARA/Configuration_adv.h
View File

@ -1940,10 +1940,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h
View File

@ -1940,10 +1940,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/Sanguinololu/Configuration_adv.h
View File

@ -1940,10 +1940,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/Tevo/Michelangelo/Configuration_adv.h
View File

@ -1939,10 +1939,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/Tevo/Tarantula Pro/Configuration_adv.h
View File

@ -1936,10 +1936,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration_adv.h
View File

@ -1939,10 +1939,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration_adv.h
View File

@ -1939,10 +1939,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/TheBorg/Configuration_adv.h
View File

@ -1940,10 +1940,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/TinyBoy2/Configuration_adv.h
View File

@ -1940,10 +1940,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/Tronxy/X3A/Configuration_adv.h
View File

@ -1940,10 +1940,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/Tronxy/X5S-2E/Configuration_adv.h
View File

@ -1940,10 +1940,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/UltiMachine/Archim1/Configuration_adv.h
View File

@ -1940,10 +1940,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/UltiMachine/Archim2/Configuration_adv.h
View File

@ -1940,10 +1940,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/VORONDesign/Configuration_adv.h
View File

@ -1940,10 +1940,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/Velleman/K8200/Configuration_adv.h
View File

@ -1953,10 +1953,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/Velleman/K8400/Configuration_adv.h
View File

@ -1940,10 +1940,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/WASP/PowerWASP/Configuration_adv.h
View File

@ -1940,10 +1940,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/Wanhao/Duplicator 6/Configuration_adv.h
View File

@ -1942,10 +1942,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/Wanhao/Duplicator i3 Mini/Configuration_adv.h
View File

@ -1940,10 +1940,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/delta/Anycubic/Kossel/Configuration_adv.h
View File

@ -1942,10 +1942,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h
View File

@ -1942,10 +1942,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/delta/FLSUN/kossel/Configuration_adv.h
View File

@ -1942,10 +1942,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h
View File

@ -1942,10 +1942,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/delta/Geeetech/Rostock 301/Configuration_adv.h
View File

@ -1942,10 +1942,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/delta/MKS/SBASE/Configuration_adv.h
View File

@ -1942,10 +1942,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/delta/Tevo Little Monster/Configuration_adv.h
View File

@ -1942,10 +1942,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/delta/generic/Configuration_adv.h
View File

@ -1942,10 +1942,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/delta/kossel_mini/Configuration_adv.h
View File

@ -1942,10 +1942,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/delta/kossel_xl/Configuration_adv.h
View File

@ -1942,10 +1942,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/gCreate/gMax1.5+/Configuration_adv.h
View File

@ -1940,10 +1940,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/makibox/Configuration_adv.h
View File

@ -1940,10 +1940,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/tvrrug/Round2/Configuration_adv.h
View File

@ -1940,10 +1940,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*

10
config/examples/wt150/Configuration_adv.h
View File

@ -1941,10 +1941,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*