bissen21/Marlin_Firmware
1
0
Fork 0
Code Issues Pull Requests Projects Releases 4 Wiki Activity

Add M851 X Y probe offsets (#15202)

Browse Source
This commit is contained in:
InsanityAutomation 2019-09-24 22:29:21 -04:00 committed by Scott Lahteine
parent ebc9a8a0b0
commit df1e51258a
151 changed files with 1009 additions and 1878 deletions
Show Stats Download Patch File Download Diff File Expand all files Collapse all files

19
Marlin/Configuration.h
View File

@ -888,11 +888,10 @@
/**
* Z Probe to nozzle (X,Y) offset, relative to (0, 0).
* X and Y offsets must be integers.
*
* In the following example the X and Y offsets are both positive:
* #define X_PROBE_OFFSET_FROM_EXTRUDER 10
* #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
*
* #define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
*
* +-- BACK ---+
* | |
@ -904,10 +903,10 @@
* | |
* O-- FRONT --+
* (0,0)
*
* Specify a Probe position as { X, Y, Z }
*/
#define X_PROBE_OFFSET_FROM_EXTRUDER 10 // X offset: -left +right [of the nozzle]
#define Y_PROBE_OFFSET_FROM_EXTRUDER 10 // Y offset: -front +behind [the nozzle]
#define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle]
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
// Certain types of probes need to stay away from edges
#define MIN_PROBE_EDGE 10
@ -941,7 +940,7 @@
*
* Use these settings to specify the distance (mm) to raise the probe (or
* lower the bed). The values set here apply over and above any (negative)
* probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
* probe Z Offset set with NOZZLE_TO_PROBE_OFFSET, M851, or the LCD.
* Only integer values >= 1 are valid here.
*
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
@ -1199,12 +1198,6 @@
#define GRID_MAX_POINTS_X 3
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
// Set the boundaries for probing (where the probe can reach).
//#define LEFT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define RIGHT_PROBE_BED_POSITION (X_BED_SIZE - (MIN_PROBE_EDGE))
//#define FRONT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define BACK_PROBE_BED_POSITION (Y_BED_SIZE - (MIN_PROBE_EDGE))
// Probe along the Y axis, advancing X after each column
//#define PROBE_Y_FIRST

2
Marlin/src/HAL/HAL_AVR/Servo.cpp
View File

@ -131,7 +131,7 @@ void initISR(timer16_Sequence_t timer) {
TCCR1A = 0; // normal counting mode
TCCR1B = _BV(CS11); // set prescaler of 8
TCNT1 = 0; // clear the timer count
#if defined(__AVR_ATmega8__)|| defined(__AVR_ATmega128__)
#if defined(__AVR_ATmega8__) || defined(__AVR_ATmega128__)
SBI(TIFR, OCF1A); // clear any pending interrupts;
SBI(TIMSK, OCIE1A); // enable the output compare interrupt
#else

2
Marlin/src/core/language.h
View File

@ -198,7 +198,7 @@
#define MSG_Z3_MAX "z3_max"
#define MSG_Z_PROBE "z_probe"
#define MSG_FILAMENT_RUNOUT_SENSOR "filament"
#define MSG_PROBE_Z_OFFSET "Probe Z Offset"
#define MSG_PROBE_OFFSET "Probe Offset"
#define MSG_SKEW_MIN "min_skew_factor: "
#define MSG_SKEW_MAX "max_skew_factor: "
#define MSG_ERR_MATERIAL_INDEX "M145 S<index> out of range (0-1)"

22
Marlin/src/core/utility.cpp
View File

@ -79,40 +79,36 @@ void safe_delay(millis_t ms) {
);
#if HAS_BED_PROBE
SERIAL_ECHOPAIR(
"Probe Offset X:" STRINGIFY(X_PROBE_OFFSET_FROM_EXTRUDER)
" Y:" STRINGIFY(Y_PROBE_OFFSET_FROM_EXTRUDER)
" Z:", zprobe_zoffset
);
if ((X_PROBE_OFFSET_FROM_EXTRUDER) > 0)
SERIAL_ECHOPAIR("Probe Offset X:", zprobe_offset[X_AXIS], " Y:", zprobe_offset[Y_AXIS], " Z:", zprobe_offset[Z_AXIS]);
if (zprobe_offset[X_AXIS] > 0)
SERIAL_ECHOPGM(" (Right");
else if ((X_PROBE_OFFSET_FROM_EXTRUDER) < 0)
else if (zprobe_offset[X_AXIS] < 0)
SERIAL_ECHOPGM(" (Left");
else if ((Y_PROBE_OFFSET_FROM_EXTRUDER) != 0)
else if (zprobe_offset[Y_AXIS] != 0)
SERIAL_ECHOPGM(" (Middle");
else
SERIAL_ECHOPGM(" (Aligned With");
if ((Y_PROBE_OFFSET_FROM_EXTRUDER) > 0) {
if (zprobe_offset[Y_AXIS] > 0) {
#if IS_SCARA
SERIAL_ECHOPGM("-Distal");
#else
SERIAL_ECHOPGM("-Back");
#endif
}
else if ((Y_PROBE_OFFSET_FROM_EXTRUDER) < 0) {
else if (zprobe_offset[Y_AXIS] < 0) {
#if IS_SCARA
SERIAL_ECHOPGM("-Proximal");
#else
SERIAL_ECHOPGM("-Front");
#endif
}
else if ((X_PROBE_OFFSET_FROM_EXTRUDER) != 0)
else if (zprobe_offset[X_AXIS] != 0)
SERIAL_ECHOPGM("-Center");
if (zprobe_zoffset < 0)
if (zprobe_offset[Z_AXIS] < 0)
SERIAL_ECHOPGM(" & Below");
else if (zprobe_zoffset > 0)
else if (zprobe_offset[Z_AXIS] > 0)
SERIAL_ECHOPGM(" & Above");
else
SERIAL_ECHOPGM(" & Same Z as");

6
Marlin/src/feature/bedlevel/ubl/ubl.cpp
View File

@ -177,11 +177,11 @@
serialprintPGM(csv ? PSTR("CSV:\n") : PSTR("LCD:\n"));
}
// Add XY_PROBE_OFFSET_FROM_EXTRUDER because probe_pt() subtracts these when
// Add XY probe offset from extruder because probe_pt() subtracts them when
// moving to the xy position to be measured. This ensures better agreement between
// the current Z position after G28 and the mesh values.
const float current_xi = find_closest_x_index(current_position[X_AXIS] + X_PROBE_OFFSET_FROM_EXTRUDER),
current_yi = find_closest_y_index(current_position[Y_AXIS] + Y_PROBE_OFFSET_FROM_EXTRUDER);
const float current_xi = find_closest_x_index(current_position[X_AXIS] + zprobe_offset[X_AXIS]),
current_yi = find_closest_y_index(current_position[Y_AXIS] + zprobe_offset[Y_AXIS]);
if (!lcd) SERIAL_EOL();
for (int8_t j = GRID_MAX_POINTS_Y - 1; j >= 0; j--) {

43
Marlin/src/feature/bedlevel/ubl/ubl_G29.cpp
View File

@ -290,7 +290,7 @@
* especially better for Delta printers, since it populates the center of the mesh first, allowing for
* a quicker test print to verify settings. You don't need to populate the entire mesh to use it.
* After all, you don't want to spend a lot of time generating a mesh only to realize the resolution
* or zprobe_zoffset are incorrect. Mesh-generation gathers points starting closest to the nozzle unless
* or probe offsets are incorrect. Mesh-generation gathers points starting closest to the nozzle unless
* an (X,Y) coordinate pair is given.
*
* Unified Bed Leveling uses a lot of EEPROM storage to hold its data, and it takes some effort to get
@ -453,7 +453,7 @@
SERIAL_ECHO(g29_y_pos);
SERIAL_ECHOLNPGM(").\n");
}
probe_entire_mesh(g29_x_pos + X_PROBE_OFFSET_FROM_EXTRUDER, g29_y_pos + Y_PROBE_OFFSET_FROM_EXTRUDER,
probe_entire_mesh(g29_x_pos + zprobe_offset[X_AXIS], g29_y_pos + zprobe_offset[Y_AXIS],
parser.seen('T'), parser.seen('E'), parser.seen('U'));
report_current_position();
@ -482,8 +482,8 @@
g29_x_pos = X_HOME_POS;
g29_y_pos = Y_HOME_POS;
#else // cartesian
g29_x_pos = X_PROBE_OFFSET_FROM_EXTRUDER > 0 ? X_BED_SIZE : 0;
g29_y_pos = Y_PROBE_OFFSET_FROM_EXTRUDER < 0 ? Y_BED_SIZE : 0;
g29_x_pos = zprobe_offset[X_AXIS] > 0 ? X_BED_SIZE : 0;
g29_y_pos = zprobe_offset[Y_AXIS] < 0 ? Y_BED_SIZE : 0;
#endif
}
@ -800,8 +800,8 @@
restore_ubl_active_state_and_leave();
do_blocking_move_to_xy(
constrain(rx - (X_PROBE_OFFSET_FROM_EXTRUDER), MESH_MIN_X, MESH_MAX_X),
constrain(ry - (Y_PROBE_OFFSET_FROM_EXTRUDER), MESH_MIN_Y, MESH_MAX_Y)
constrain(rx - zprobe_offset[X_AXIS], MESH_MIN_X, MESH_MAX_X),
constrain(ry - zprobe_offset[Y_AXIS], MESH_MIN_Y, MESH_MAX_Y)
);
}
@ -1281,8 +1281,8 @@
out_mesh.distance = -99999.9f;
// Get our reference position. Either the nozzle or probe location.
const float px = rx + (probe_as_reference == USE_PROBE_AS_REFERENCE ? X_PROBE_OFFSET_FROM_EXTRUDER : 0),
py = ry + (probe_as_reference == USE_PROBE_AS_REFERENCE ? Y_PROBE_OFFSET_FROM_EXTRUDER : 0);
const float px = rx + (probe_as_reference == USE_PROBE_AS_REFERENCE ? zprobe_offset[X_AXIS] : 0),
py = ry + (probe_as_reference == USE_PROBE_AS_REFERENCE ? zprobe_offset[Y_AXIS] : 0);
float best_so_far = 99999.99f;
@ -1384,22 +1384,17 @@
#include "../../../libs/vector_3.h"
void unified_bed_leveling::tilt_mesh_based_on_probed_grid(const bool do_3_pt_leveling) {
constexpr int16_t x_min = _MAX(MIN_PROBE_X, MESH_MIN_X),
x_max = _MIN(MAX_PROBE_X, MESH_MAX_X),
y_min = _MAX(MIN_PROBE_Y, MESH_MIN_Y),
y_max = _MIN(MAX_PROBE_Y, MESH_MAX_Y);
bool abort_flag = false;
const float x_min = probe_min_x(), x_max = probe_max_x(),
y_min = probe_min_y(), y_max = probe_max_y(),
dx = (x_max - x_min) / (g29_grid_size - 1),
dy = (y_max - y_min) / (g29_grid_size - 1);
float measured_z;
bool abort_flag = false;
const float dx = float(x_max - x_min) / (g29_grid_size - 1),
dy = float(y_max - y_min) / (g29_grid_size - 1);
//float z1, z2, z3; // Needed for algorithm validation below
struct linear_fit_data lsf_results;
//float z1, z2, z3; // Needed for algorithm validation down below.
incremental_LSF_reset(&lsf_results);
if (do_3_pt_leveling) {
@ -1478,9 +1473,9 @@
uint16_t total_points = g29_grid_size * g29_grid_size, point_num = 1;
for (uint8_t ix = 0; ix < g29_grid_size; ix++) {
const float rx = float(x_min) + ix * dx;
const float rx = x_min + ix * dx;
for (int8_t iy = 0; iy < g29_grid_size; iy++) {
const float ry = float(y_min) + dy * (zig_zag ? g29_grid_size - 1 - iy : iy);
const float ry = y_min + dy * (zig_zag ? g29_grid_size - 1 - iy : iy);
if (!abort_flag) {
SERIAL_ECHOLNPAIR("Tilting mesh point ", point_num, "/", total_points, "\n");
@ -1505,7 +1500,7 @@
DEBUG_ECHOPAIR_F(" correction: ", get_z_correction(rx, ry), 7);
}
measured_z -= get_z_correction(rx, ry) /* + zprobe_zoffset */ ;
measured_z -= get_z_correction(rx, ry) /* + zprobe_offset[Z_AXIS] */ ;
if (DEBUGGING(LEVELING)) DEBUG_ECHOLNPAIR_F(" final >>>---> ", measured_z, 7);
@ -1711,13 +1706,13 @@
serial_delay(50);
#if ENABLED(ENABLE_LEVELING_FADE_HEIGHT)
SERIAL_ECHOLNPAIR_F("planner.z_fade_height : ", planner.z_fade_height, 4);
SERIAL_ECHOLNPAIR_F("Fade Height M420 Z", planner.z_fade_height, 4);
#endif
adjust_mesh_to_mean(g29_c_flag, g29_constant);
#if HAS_BED_PROBE
SERIAL_ECHOLNPAIR_F("zprobe_zoffset: ", zprobe_zoffset, 7);
SERIAL_ECHOLNPAIR_F("Probe Offset M851 Z", zprobe_offset[Z_AXIS], 7);
#endif
SERIAL_ECHOLNPAIR("MESH_MIN_X " STRINGIFY(MESH_MIN_X) "=", MESH_MIN_X); serial_delay(50);

10
Marlin/src/gcode/bedlevel/G42.cpp
View File

@ -47,10 +47,12 @@ void GcodeSuite::G42() {
set_destination_from_current();
if (hasI) destination[X_AXIS] = _GET_MESH_X(ix);
if (hasJ) destination[Y_AXIS] = _GET_MESH_Y(iy);
if (parser.boolval('P')) {
if (hasI) destination[X_AXIS] -= X_PROBE_OFFSET_FROM_EXTRUDER;
if (hasJ) destination[Y_AXIS] -= Y_PROBE_OFFSET_FROM_EXTRUDER;
}
#if HAS_BED_PROBE
if (parser.boolval('P')) {
if (hasI) destination[X_AXIS] -= zprobe_offset[X_AXIS];
if (hasJ) destination[Y_AXIS] -= zprobe_offset[Y_AXIS];
}
#endif
const float fval = parser.linearval('F');
if (fval > 0.0) feedrate_mm_s = MMM_TO_MMS(fval);

20
Marlin/src/gcode/bedlevel/M420.cpp
View File

@ -64,10 +64,12 @@ void GcodeSuite::M420() {
#if ENABLED(MARLIN_DEV_MODE)
if (parser.intval('S') == 2) {
#if ENABLED(AUTO_BED_LEVELING_BILINEAR)
bilinear_start[X_AXIS] = MIN_PROBE_X;
bilinear_start[Y_AXIS] = MIN_PROBE_Y;
bilinear_grid_spacing[X_AXIS] = (MAX_PROBE_X - (MIN_PROBE_X)) / (GRID_MAX_POINTS_X - 1);
bilinear_grid_spacing[Y_AXIS] = (MAX_PROBE_Y - (MIN_PROBE_Y)) / (GRID_MAX_POINTS_Y - 1);
const float x_min = probe_min_x(), x_max = probe_max_x(),
y_min = probe_min_y(), y_max = probe_max_y();
bilinear_start[X_AXIS] = x_min;
bilinear_start[Y_AXIS] = y_min;
bilinear_grid_spacing[X_AXIS] = (x_max - x_min) / (GRID_MAX_POINTS_X - 1);
bilinear_grid_spacing[Y_AXIS] = (y_max - y_min) / (GRID_MAX_POINTS_Y - 1);
#endif
for (uint8_t x = 0; x < GRID_MAX_POINTS_X; x++)
for (uint8_t y = 0; y < GRID_MAX_POINTS_Y; y++) {
@ -76,11 +78,11 @@ void GcodeSuite::M420() {
ExtUI::onMeshUpdate(x, y, Z_VALUES(x, y));
#endif
}
SERIAL_ECHOPGM("Simulated " STRINGIFY(GRID_MAX_POINTS_X) "x" STRINGIFY(GRID_MAX_POINTS_X) " mesh ");
SERIAL_ECHOPAIR(" (", MIN_PROBE_X);
SERIAL_CHAR(','); SERIAL_ECHO(MIN_PROBE_Y);
SERIAL_ECHOPAIR(")-(", MAX_PROBE_X);
SERIAL_CHAR(','); SERIAL_ECHO(MAX_PROBE_Y);
SERIAL_ECHOPGM("Simulated " STRINGIFY(GRID_MAX_POINTS_X) "x" STRINGIFY(GRID_MAX_POINTS_Y) " mesh ");
SERIAL_ECHOPAIR(" (", x_min);
SERIAL_CHAR(','); SERIAL_ECHO(y_min);
SERIAL_ECHOPAIR(")-(", x_max);
SERIAL_CHAR(','); SERIAL_ECHO(y_max);
SERIAL_ECHOLNPGM(")");
}
#endif

20
Marlin/src/gcode/bedlevel/abl/G29.cpp
View File

@ -393,16 +393,16 @@ G29_TYPE GcodeSuite::G29() {
if (parser.seen('H')) {
const int16_t size = (int16_t)parser.value_linear_units();
left_probe_bed_position = _MAX(X_CENTER - size / 2, MIN_PROBE_X);
right_probe_bed_position = _MIN(left_probe_bed_position + size, MAX_PROBE_X);
front_probe_bed_position = _MAX(Y_CENTER - size / 2, MIN_PROBE_Y);
back_probe_bed_position = _MIN(front_probe_bed_position + size, MAX_PROBE_Y);
left_probe_bed_position = _MAX(X_CENTER - size / 2, probe_min_x());
right_probe_bed_position = _MIN(left_probe_bed_position + size, probe_max_x());
front_probe_bed_position = _MAX(Y_CENTER - size / 2, probe_min_y());
back_probe_bed_position = _MIN(front_probe_bed_position + size, probe_max_y());
}
else {
left_probe_bed_position = parser.seenval('L') ? (int)RAW_X_POSITION(parser.value_linear_units()) : LEFT_PROBE_BED_POSITION;
right_probe_bed_position = parser.seenval('R') ? (int)RAW_X_POSITION(parser.value_linear_units()) : RIGHT_PROBE_BED_POSITION;
front_probe_bed_position = parser.seenval('F') ? (int)RAW_Y_POSITION(parser.value_linear_units()) : FRONT_PROBE_BED_POSITION;
back_probe_bed_position = parser.seenval('B') ? (int)RAW_Y_POSITION(parser.value_linear_units()) : BACK_PROBE_BED_POSITION;
left_probe_bed_position = parser.seenval('L') ? (int)RAW_X_POSITION(parser.value_linear_units()) : _MAX(X_CENTER - X_BED_SIZE / 2, probe_min_x());
right_probe_bed_position = parser.seenval('R') ? (int)RAW_X_POSITION(parser.value_linear_units()) : _MIN(left_probe_bed_position + X_BED_SIZE, probe_max_x());
front_probe_bed_position = parser.seenval('F') ? (int)RAW_Y_POSITION(parser.value_linear_units()) : _MAX(Y_CENTER - Y_BED_SIZE / 2, probe_min_y());
back_probe_bed_position = parser.seenval('B') ? (int)RAW_Y_POSITION(parser.value_linear_units()) : _MIN(front_probe_bed_position + Y_BED_SIZE, probe_max_y());
}
if (
@ -947,8 +947,8 @@ G29_TYPE GcodeSuite::G29() {
planner.leveling_active = false;
// Use the last measured distance to the bed, if possible
if ( NEAR(current_position[X_AXIS], xProbe - (X_PROBE_OFFSET_FROM_EXTRUDER))
&& NEAR(current_position[Y_AXIS], yProbe - (Y_PROBE_OFFSET_FROM_EXTRUDER))
if ( NEAR(current_position[X_AXIS], xProbe - zprobe_offset[X_AXIS])
&& NEAR(current_position[Y_AXIS], yProbe - zprobe_offset[Y_AXIS])
) {
const float simple_z = current_position[Z_AXIS] - measured_z;
if (DEBUGGING(LEVELING)) DEBUG_ECHOLNPAIR("Probed Z", simple_z, " Matrix Z", converted[Z_AXIS], " Discrepancy ", simple_z - converted[Z_AXIS]);

4
Marlin/src/gcode/calibrate/G28.cpp
View File

@ -136,8 +136,8 @@
destination[Z_AXIS] = current_position[Z_AXIS]; // Z is already at the right height
#if HOMING_Z_WITH_PROBE
destination[X_AXIS] -= X_PROBE_OFFSET_FROM_EXTRUDER;
destination[Y_AXIS] -= Y_PROBE_OFFSET_FROM_EXTRUDER;
destination[X_AXIS] -= zprobe_offset[X_AXIS];
destination[Y_AXIS] -= zprobe_offset[Y_AXIS];
#endif
if (position_is_reachable(destination[X_AXIS], destination[Y_AXIS])) {

8
Marlin/src/gcode/calibrate/M48.cpp
View File

@ -77,8 +77,8 @@ void GcodeSuite::M48() {
float X_current = current_position[X_AXIS],
Y_current = current_position[Y_AXIS];
const float X_probe_location = parser.linearval('X', X_current + X_PROBE_OFFSET_FROM_EXTRUDER),
Y_probe_location = parser.linearval('Y', Y_current + Y_PROBE_OFFSET_FROM_EXTRUDER);
const float X_probe_location = parser.linearval('X', X_current + zprobe_offset[X_AXIS]),
Y_probe_location = parser.linearval('Y', Y_current + zprobe_offset[Y_AXIS]);
if (!position_is_reachable_by_probe(X_probe_location, Y_probe_location)) {
SERIAL_ECHOLNPGM("? (X,Y) out of bounds.");
@ -165,8 +165,8 @@ void GcodeSuite::M48() {
while (angle < 0.0) angle += 360.0; // outside of this range. It looks like they behave correctly with
// numbers outside of the range, but just to be safe we clamp them.
X_current = X_probe_location - (X_PROBE_OFFSET_FROM_EXTRUDER) + cos(RADIANS(angle)) * radius;
Y_current = Y_probe_location - (Y_PROBE_OFFSET_FROM_EXTRUDER) + sin(RADIANS(angle)) * radius;
X_current = X_probe_location - zprobe_offset[X_AXIS] + cos(RADIANS(angle)) * radius;
Y_current = Y_probe_location - zprobe_offset[Y_AXIS] + sin(RADIANS(angle)) * radius;
#if DISABLED(DELTA)
LIMIT(X_current, X_MIN_POS, X_MAX_POS);

2
Marlin/src/gcode/gcode.h
View File

@ -229,7 +229,7 @@
* M701 - Load filament (Requires FILAMENT_LOAD_UNLOAD_GCODES)
* M702 - Unload filament (Requires FILAMENT_LOAD_UNLOAD_GCODES)
* M810-M819 - Define/execute a G-code macro (Requires GCODE_MACROS)
* M851 - Set Z probe's Z offset in current units. (Negative = below the nozzle.)
* M851 - Set Z probe's XYZ offsets in current units. (Negative values: X=left, Y=front, Z=below)
* M852 - Set skew factors: "M852 [I<xy>] [J<xz>] [K<yz>]". (Requires SKEW_CORRECTION_GCODE, and SKEW_CORRECTION_FOR_Z for IJ)
* M860 - Report the position of position encoder modules.
* M861 - Report the status of position encoder modules.

4
Marlin/src/gcode/motion/M290.cpp
View File

@ -42,9 +42,9 @@
&& active_extruder == 0
#endif
) {
zprobe_zoffset += offs;
zprobe_offset[Z_AXIS] += offs;
SERIAL_ECHO_START();
SERIAL_ECHOLNPAIR(MSG_PROBE_Z_OFFSET ": ", zprobe_zoffset);
SERIAL_ECHOLNPAIR(MSG_PROBE_OFFSET MSG_Z ": ", zprobe_offset[Z_AXIS]);
}
#if ENABLED(BABYSTEP_HOTEND_Z_OFFSET)
else {

4
Marlin/src/gcode/probe/G30.cpp
View File

@ -39,8 +39,8 @@
* E Engage the probe for each probe (default 1)
*/
void GcodeSuite::G30() {
const float xpos = parser.linearval('X', current_position[X_AXIS] + X_PROBE_OFFSET_FROM_EXTRUDER),
ypos = parser.linearval('Y', current_position[Y_AXIS] + Y_PROBE_OFFSET_FROM_EXTRUDER);
const float xpos = parser.linearval('X', current_position[X_AXIS] + zprobe_offset[X_AXIS]),
ypos = parser.linearval('Y', current_position[Y_AXIS] + zprobe_offset[Y_AXIS]);
if (!position_is_reachable_by_probe(xpos, ypos)) return;

42
Marlin/src/gcode/probe/M851.cpp
View File

@ -28,17 +28,43 @@
#include "../../feature/bedlevel/bedlevel.h"
#include "../../module/probe.h"
/**
* M851: Set the nozzle-to-probe offsets in current units
*/
void GcodeSuite::M851() {
if (parser.seenval('Z')) {
const float value = parser.value_linear_units();
if (WITHIN(value, Z_PROBE_OFFSET_RANGE_MIN, Z_PROBE_OFFSET_RANGE_MAX))
zprobe_zoffset = value;
else
SERIAL_ERROR_MSG("?Z out of range (" STRINGIFY(Z_PROBE_OFFSET_RANGE_MIN) " to " STRINGIFY(Z_PROBE_OFFSET_RANGE_MAX) ")");
// Show usage with no parameters
if (!parser.seen("XYZ")) {
SERIAL_ECHO_START();
SERIAL_ECHOLNPAIR(MSG_PROBE_OFFSET " X", zprobe_offset[X_AXIS],
" Y", zprobe_offset[Y_AXIS],
" Z", zprobe_offset[Z_AXIS]);
return;
}
SERIAL_ECHO_START();
SERIAL_ECHOLNPAIR(MSG_PROBE_Z_OFFSET ": ", zprobe_zoffset);
// Get the modified offsets
const float offs[] = {
parser.floatval('X', zprobe_offset[X_AXIS]),
parser.floatval('Y', zprobe_offset[Y_AXIS]),
parser.floatval('Z', zprobe_offset[Z_AXIS])
};
// Error-check
if (!WITHIN(offs[X_AXIS], -(X_BED_SIZE), X_BED_SIZE)) {
SERIAL_ERROR_MSG("?X out of range (-" STRINGIFY(X_BED_SIZE) " to " STRINGIFY(X_BED_SIZE) ")");
return;
}
if (!WITHIN(offs[Y_AXIS], -(Y_BED_SIZE), Y_BED_SIZE)) {
SERIAL_ERROR_MSG("?Y out of range (-" STRINGIFY(Y_BED_SIZE) " to " STRINGIFY(Y_BED_SIZE) ")");
return;
}
if (!WITHIN(offs[Z_AXIS], Z_PROBE_OFFSET_RANGE_MIN, Z_PROBE_OFFSET_RANGE_MAX)) {
SERIAL_ERROR_MSG("?Z out of range (" STRINGIFY(Z_PROBE_OFFSET_RANGE_MIN) " to " STRINGIFY(Z_PROBE_OFFSET_RANGE_MAX) ")");
return;
}
// Save the new offsets
LOOP_XYZ(a) zprobe_offset[a] = offs[a];
}
#endif // HAS_BED_PROBE

95
Marlin/src/inc/Conditionals_post.h
View File

@ -1348,12 +1348,7 @@
#endif
#endif
#else
#undef X_PROBE_OFFSET_FROM_EXTRUDER
#undef Y_PROBE_OFFSET_FROM_EXTRUDER
#undef Z_PROBE_OFFSET_FROM_EXTRUDER
#define X_PROBE_OFFSET_FROM_EXTRUDER 0
#define Y_PROBE_OFFSET_FROM_EXTRUDER 0
#define Z_PROBE_OFFSET_FROM_EXTRUDER 0
#undef NOZZLE_TO_PROBE_OFFSET
#endif
/**
@ -1446,10 +1441,13 @@
* Bed Probing rectangular bounds
* These can be further constrained in code for Delta and SCARA
*/
#ifndef MIN_PROBE_EDGE
#define MIN_PROBE_EDGE 0
#endif
#ifndef NOZZLE_TO_PROBE_OFFSET
#define NOZZLE_TO_PROBE_OFFSET { 0, 0, 0 }
#endif
constexpr float nozzle_to_probe_offset[XYZ] = NOZZLE_TO_PROBE_OFFSET;
#if ENABLED(DELTA)
/**
@ -1457,8 +1455,8 @@
*/
#define _PROBE_RADIUS (DELTA_PRINTABLE_RADIUS - (MIN_PROBE_EDGE))
#ifndef DELTA_CALIBRATION_RADIUS
#ifdef X_PROBE_OFFSET_FROM_EXTRUDER
#define DELTA_CALIBRATION_RADIUS (DELTA_PRINTABLE_RADIUS - _MAX(ABS(X_PROBE_OFFSET_FROM_EXTRUDER), ABS(Y_PROBE_OFFSET_FROM_EXTRUDER), ABS(MIN_PROBE_EDGE)))
#ifdef NOZZLE_TO_PROBE_OFFSET
#define DELTA_CALIBRATION_RADIUS (DELTA_PRINTABLE_RADIUS - _MAX(ABS(nozzle_to_probe_offset[X_AXIS]), ABS(nozzle_to_probe_offset[Y_AXIS]), ABS(MIN_PROBE_EDGE)))
#else
#define DELTA_CALIBRATION_RADIUS _PROBE_RADIUS
#endif
@ -1467,39 +1465,39 @@
#define DELTA_ENDSTOP_ADJ { 0, 0, 0 }
#endif
#ifndef DELTA_TOWER_ANGLE_TRIM
#define DELTA_TOWER_ANGLE_TRIM {0, 0, 0}
#define DELTA_TOWER_ANGLE_TRIM { 0, 0, 0 }
#endif
#ifndef DELTA_RADIUS_TRIM_TOWER
#define DELTA_RADIUS_TRIM_TOWER {0, 0, 0}
#define DELTA_RADIUS_TRIM_TOWER { 0, 0, 0 }
#endif
#ifndef DELTA_DIAGONAL_ROD_TRIM_TOWER
#define DELTA_DIAGONAL_ROD_TRIM_TOWER {0, 0, 0}
#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0, 0, 0 }
#endif
// Probing points may be verified at compile time within the radius
// using static_assert(HYPOT2(X2-X1,Y2-Y1)<=sq(DELTA_PRINTABLE_RADIUS),"bad probe point!")
// so that may be added to SanityCheck.h in the future.
#define _MIN_PROBE_X (X_CENTER - (_PROBE_RADIUS))
#define _MIN_PROBE_Y (Y_CENTER - (_PROBE_RADIUS))
#define _MAX_PROBE_X (X_CENTER + _PROBE_RADIUS)
#define _MAX_PROBE_Y (Y_CENTER + _PROBE_RADIUS)
#define PROBE_X_MIN (X_CENTER - (_PROBE_RADIUS))
#define PROBE_Y_MIN (Y_CENTER - (_PROBE_RADIUS))
#define PROBE_X_MAX (X_CENTER + _PROBE_RADIUS)
#define PROBE_Y_MAX (Y_CENTER + _PROBE_RADIUS)
#elif IS_SCARA
#define SCARA_PRINTABLE_RADIUS (SCARA_LINKAGE_1 + SCARA_LINKAGE_2)
#define _PROBE_RADIUS (SCARA_PRINTABLE_RADIUS - (MIN_PROBE_EDGE))
#define _MIN_PROBE_X (X_CENTER - (SCARA_PRINTABLE_RADIUS) + MIN_PROBE_EDGE)
#define _MIN_PROBE_Y (Y_CENTER - (SCARA_PRINTABLE_RADIUS) + MIN_PROBE_EDGE)
#define _MAX_PROBE_X (X_CENTER + SCARA_PRINTABLE_RADIUS - (MIN_PROBE_EDGE))
#define _MAX_PROBE_Y (Y_CENTER + SCARA_PRINTABLE_RADIUS - (MIN_PROBE_EDGE))
#define PROBE_X_MIN (X_CENTER - (SCARA_PRINTABLE_RADIUS) + MIN_PROBE_EDGE)
#define PROBE_Y_MIN (Y_CENTER - (SCARA_PRINTABLE_RADIUS) + MIN_PROBE_EDGE)
#define PROBE_X_MAX (X_CENTER + SCARA_PRINTABLE_RADIUS - (MIN_PROBE_EDGE))
#define PROBE_Y_MAX (Y_CENTER + SCARA_PRINTABLE_RADIUS - (MIN_PROBE_EDGE))
#else
// Boundaries for Cartesian probing based on bed limits
#define _MIN_PROBE_X (_MAX(X_MIN_BED + MIN_PROBE_EDGE, X_MIN_POS + X_PROBE_OFFSET_FROM_EXTRUDER))
#define _MIN_PROBE_Y (_MAX(Y_MIN_BED + MIN_PROBE_EDGE, Y_MIN_POS + Y_PROBE_OFFSET_FROM_EXTRUDER))
#define _MAX_PROBE_X (_MIN(X_MAX_BED - (MIN_PROBE_EDGE), X_MAX_POS + X_PROBE_OFFSET_FROM_EXTRUDER))
#define _MAX_PROBE_Y (_MIN(Y_MAX_BED - (MIN_PROBE_EDGE), Y_MAX_POS + Y_PROBE_OFFSET_FROM_EXTRUDER))
#define PROBE_X_MIN (_MAX(X_MIN_BED + MIN_PROBE_EDGE, X_MIN_POS + nozzle_to_probe_offset[X_AXIS]))
#define PROBE_Y_MIN (_MAX(Y_MIN_BED + MIN_PROBE_EDGE, Y_MIN_POS + nozzle_to_probe_offset[Y_AXIS]))
#define PROBE_X_MAX (_MIN(X_MAX_BED - (MIN_PROBE_EDGE), X_MAX_POS + nozzle_to_probe_offset[X_AXIS]))
#define PROBE_Y_MAX (_MIN(Y_MAX_BED - (MIN_PROBE_EDGE), Y_MAX_POS + nozzle_to_probe_offset[Y_AXIS]))
#endif
@ -1507,20 +1505,6 @@
#define LEVELED_SEGMENT_LENGTH 5
#endif
// These may be overridden in Configuration.h if a smaller area is desired
#ifndef MIN_PROBE_X
#define MIN_PROBE_X _MIN_PROBE_X
#endif
#ifndef MIN_PROBE_Y
#define MIN_PROBE_Y _MIN_PROBE_Y
#endif
#ifndef MAX_PROBE_X
#define MAX_PROBE_X _MAX_PROBE_X
#endif
#ifndef MAX_PROBE_Y
#define MAX_PROBE_Y _MAX_PROBE_Y
#endif
/**
* Default mesh area is an area with an inset margin on the print area.
*/
@ -1537,14 +1521,14 @@
// Boundaries for Cartesian probing based on set limits
#if ENABLED(AUTO_BED_LEVELING_UBL)
#define _MESH_MIN_X (_MAX(X_MIN_BED + MESH_INSET, X_MIN_POS)) // UBL is careful not to probe off the bed. It does not
#define _MESH_MIN_Y (_MAX(Y_MIN_BED + MESH_INSET, Y_MIN_POS)) // need *_PROBE_OFFSET_FROM_EXTRUDER in the mesh dimensions
#define _MESH_MIN_Y (_MAX(Y_MIN_BED + MESH_INSET, Y_MIN_POS)) // need NOZZLE_TO_PROBE_OFFSET in the mesh dimensions
#define _MESH_MAX_X (_MIN(X_MAX_BED - (MESH_INSET), X_MAX_POS))
#define _MESH_MAX_Y (_MIN(Y_MAX_BED - (MESH_INSET), Y_MAX_POS))
#else
#define _MESH_MIN_X (_MAX(X_MIN_BED + MESH_INSET, X_MIN_POS + X_PROBE_OFFSET_FROM_EXTRUDER))
#define _MESH_MIN_Y (_MAX(Y_MIN_BED + MESH_INSET, Y_MIN_POS + Y_PROBE_OFFSET_FROM_EXTRUDER))
#define _MESH_MAX_X (_MIN(X_MAX_BED - (MESH_INSET), X_MAX_POS + X_PROBE_OFFSET_FROM_EXTRUDER))
#define _MESH_MAX_Y (_MIN(Y_MAX_BED - (MESH_INSET), Y_MAX_POS + Y_PROBE_OFFSET_FROM_EXTRUDER))
#define _MESH_MIN_X (_MAX(X_MIN_BED + MESH_INSET, X_MIN_POS + nozzle_to_probe_offset[X_AXIS]))
#define _MESH_MIN_Y (_MAX(Y_MIN_BED + MESH_INSET, Y_MIN_POS + nozzle_to_probe_offset[Y_AXIS]))
#define _MESH_MAX_X (_MIN(X_MAX_BED - (MESH_INSET), X_MAX_POS + nozzle_to_probe_offset[X_AXIS]))
#define _MESH_MAX_Y (_MIN(Y_MAX_BED - (MESH_INSET), Y_MAX_POS + nozzle_to_probe_offset[Y_AXIS]))
#endif
#endif
@ -1592,41 +1576,26 @@
#endif
#else
#ifndef PROBE_PT_1_X
#define PROBE_PT_1_X MIN_PROBE_X
#define PROBE_PT_1_X PROBE_X_MIN
#endif
#ifndef PROBE_PT_1_Y
#define PROBE_PT_1_Y MIN_PROBE_Y
#define PROBE_PT_1_Y PROBE_Y_MIN
#endif
#ifndef PROBE_PT_2_X
#define PROBE_PT_2_X MAX_PROBE_X
#define PROBE_PT_2_X PROBE_X_MAX
#endif
#ifndef PROBE_PT_2_Y
#define PROBE_PT_2_Y MIN_PROBE_Y
#define PROBE_PT_2_Y PROBE_Y_MIN
#endif
#ifndef PROBE_PT_3_X
#define PROBE_PT_3_X X_CENTER
#endif
#ifndef PROBE_PT_3_Y
#define PROBE_PT_3_Y MAX_PROBE_Y
#define PROBE_PT_3_Y PROBE_Y_MAX
#endif
#endif
#endif
#if EITHER(AUTO_BED_LEVELING_LINEAR, AUTO_BED_LEVELING_BILINEAR)
#ifndef LEFT_PROBE_BED_POSITION
#define LEFT_PROBE_BED_POSITION MIN_PROBE_X
#endif
#ifndef RIGHT_PROBE_BED_POSITION
#define RIGHT_PROBE_BED_POSITION MAX_PROBE_X
#endif
#ifndef FRONT_PROBE_BED_POSITION
#define FRONT_PROBE_BED_POSITION MIN_PROBE_Y
#endif
#ifndef BACK_PROBE_BED_POSITION
#define BACK_PROBE_BED_POSITION MAX_PROBE_Y
#endif
#endif
/**
* Buzzer/Speaker
*/

48
Marlin/src/inc/SanityCheck.h
View File

@ -390,6 +390,10 @@
#error "STRING_SPLASH_LINE[12] are now obsolete. Please remove them from Configuration.h."
#elif defined(Z_PROBE_ALLEN_KEY_DEPLOY_1_X) || defined(Z_PROBE_ALLEN_KEY_STOW_1_X)
#error "Z_PROBE_ALLEN_KEY_(DEPLOY|STOW) coordinates are now a single setting. Please update your configuration."
#elif defined(X_PROBE_OFFSET_FROM_EXTRUDER) || defined(Y_PROBE_OFFSET_FROM_EXTRUDER) || defined(Z_PROBE_OFFSET_FROM_EXTRUDER)
#error "[XYZ]_PROBE_OFFSET_FROM_EXTRUDER is now NOZZLE_TO_PROBE_OFFSET. Please update your configuration."
#elif defined(MIN_PROBE_X) || defined(MIN_PROBE_Y) || defined(MAX_PROBE_X) || defined(MAX_PROBE_Y)
#error "(MIN|MAX)_PROBE_[XY] are now calculated at runtime. Please remove them from Configuration.h."
#endif
#define BOARD_MKS_13 -1000
@ -1051,9 +1055,6 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS
#if HAS_BED_PROBE
static_assert(FLOOR(float(X_PROBE_OFFSET_FROM_EXTRUDER)) == float(X_PROBE_OFFSET_FROM_EXTRUDER), "X_PROBE_OFFSET_FROM_EXTRUDER must be an integer!");
static_assert(FLOOR(float(Y_PROBE_OFFSET_FROM_EXTRUDER)) == float(Y_PROBE_OFFSET_FROM_EXTRUDER), "Y_PROBE_OFFSET_FROM_EXTRUDER must be an integer!");
/**
* Z_PROBE_SLED is incompatible with DELTA
*/
@ -1205,14 +1206,18 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS
* Bed Leveling Requirements
*/
#if EITHER(AUTO_BED_LEVELING_UBL, AUTO_BED_LEVELING_3POINT)
static_assert(WITHIN(PROBE_PT_1_X, MIN_PROBE_X, MAX_PROBE_X), "PROBE_PT_1_X is outside the probe region.");
static_assert(WITHIN(PROBE_PT_2_X, MIN_PROBE_X, MAX_PROBE_X), "PROBE_PT_2_X is outside the probe region.");
static_assert(WITHIN(PROBE_PT_3_X, MIN_PROBE_X, MAX_PROBE_X), "PROBE_PT_3_X is outside the probe region.");
static_assert(WITHIN(PROBE_PT_1_Y, MIN_PROBE_Y, MAX_PROBE_Y), "PROBE_PT_1_Y is outside the probe region.");
static_assert(WITHIN(PROBE_PT_2_Y, MIN_PROBE_Y, MAX_PROBE_Y), "PROBE_PT_2_Y is outside the probe region.");
static_assert(WITHIN(PROBE_PT_3_Y, MIN_PROBE_Y, MAX_PROBE_Y), "PROBE_PT_3_Y is outside the probe region.");
#endif
//
// !! TODO: REPLACE WITH TESTS IN THE 3-POINT LEVELING CODE !!
//
//#if EITHER(AUTO_BED_LEVELING_UBL, AUTO_BED_LEVELING_3POINT)
// static_assert(WITHIN(PROBE_PT_1_X, PROBE_X_MIN, PROBE_X_MAX), "PROBE_PT_1_X is outside the probe region.");
// static_assert(WITHIN(PROBE_PT_2_X, PROBE_X_MIN, PROBE_X_MAX), "PROBE_PT_2_X is outside the probe region.");
// static_assert(WITHIN(PROBE_PT_3_X, PROBE_X_MIN, PROBE_X_MAX), "PROBE_PT_3_X is outside the probe region.");
// static_assert(WITHIN(PROBE_PT_1_Y, PROBE_Y_MIN, PROBE_Y_MAX), "PROBE_PT_1_Y is outside the probe region.");
// static_assert(WITHIN(PROBE_PT_2_Y, PROBE_Y_MIN, PROBE_Y_MAX), "PROBE_PT_2_Y is outside the probe region.");
// static_assert(WITHIN(PROBE_PT_3_Y, PROBE_Y_MIN, PROBE_Y_MAX), "PROBE_PT_3_Y is outside the probe region.");
//#endif
#if ENABLED(AUTO_BED_LEVELING_UBL)
@ -1246,20 +1251,6 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS
#error "SCARA machines can only use the AUTO_BED_LEVELING_BILINEAR leveling option."
#endif
/**
* Check auto bed leveling probe points
*/
#if ABL_GRID
static_assert(LEFT_PROBE_BED_POSITION < RIGHT_PROBE_BED_POSITION, "LEFT_PROBE_BED_POSITION must be less than RIGHT_PROBE_BED_POSITION.");
static_assert(FRONT_PROBE_BED_POSITION < BACK_PROBE_BED_POSITION, "FRONT_PROBE_BED_POSITION must be less than BACK_PROBE_BED_POSITION.");
static_assert(LEFT_PROBE_BED_POSITION >= MIN_PROBE_X, "LEFT_PROBE_BED_POSITION is outside the probe region.");
static_assert(RIGHT_PROBE_BED_POSITION <= MAX_PROBE_X, "RIGHT_PROBE_BED_POSITION is outside the probe region.");
static_assert(FRONT_PROBE_BED_POSITION >= MIN_PROBE_Y, "FRONT_PROBE_BED_POSITION is outside the probe region.");
static_assert(BACK_PROBE_BED_POSITION <= MAX_PROBE_Y, "BACK_PROBE_BED_POSITION is outside the probe region.");
#endif
#elif ENABLED(MESH_BED_LEVELING)
// Hide PROBE_MANUALLY from the rest of the code
@ -1328,8 +1319,11 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS
*/
#if ENABLED(Z_SAFE_HOMING)
#if HAS_BED_PROBE
static_assert(WITHIN(Z_SAFE_HOMING_X_POINT, MIN_PROBE_X, MAX_PROBE_X), "Z_SAFE_HOMING_X_POINT is outside the probe region.");
static_assert(WITHIN(Z_SAFE_HOMING_Y_POINT, MIN_PROBE_Y, MAX_PROBE_Y), "Z_SAFE_HOMING_Y_POINT is outside the probe region.");
//
// !! TODO: REPLACE WITH TESTS IN THE Z_SAFE_HOMING CODE !!
//
//static_assert(WITHIN(Z_SAFE_HOMING_X_POINT, PROBE_X_MIN, PROBE_X_MAX), "Z_SAFE_HOMING_X_POINT is outside the probe region.");
//static_assert(WITHIN(Z_SAFE_HOMING_Y_POINT, PROBE_Y_MIN, PROBE_Y_MAX), "Z_SAFE_HOMING_Y_POINT is outside the probe region.");
#else
static_assert(WITHIN(Z_SAFE_HOMING_X_POINT, X_MIN_POS, X_MAX_POS), "Z_SAFE_HOMING_X_POINT can't be reached by the nozzle.");
static_assert(WITHIN(Z_SAFE_HOMING_Y_POINT, Y_MIN_POS, Y_MAX_POS), "Z_SAFE_HOMING_Y_POINT can't be reached by the nozzle.");

6
Marlin/src/lcd/extensible_ui/ui_api.cpp
View File

@ -708,7 +708,7 @@ namespace ExtUI {
#if EXTRUDERS > 1
&& (linked_nozzles || active_extruder == 0)
#endif
) zprobe_zoffset += mm;
) zprobe_offset[Z_AXIS] += mm;
#else
UNUSED(mm);
#endif
@ -746,7 +746,7 @@ namespace ExtUI {
float getZOffset_mm() {
#if HAS_BED_PROBE
return zprobe_zoffset;
return zprobe_offset[Z_AXIS];
#elif ENABLED(BABYSTEP_DISPLAY_TOTAL)
return babystep.axis_total[BS_TOTAL_AXIS(Z_AXIS) + 1];
#else
@ -757,7 +757,7 @@ namespace ExtUI {
void setZOffset_mm(const float value) {
#if HAS_BED_PROBE
if (WITHIN(value, Z_PROBE_OFFSET_RANGE_MIN, Z_PROBE_OFFSET_RANGE_MAX))
zprobe_zoffset = value;
zprobe_offset[Z_AXIS] = value;
#elif ENABLED(BABYSTEP_DISPLAY_TOTAL)
babystep.add_mm(Z_AXIS, (value - babystep.axis_total[BS_TOTAL_AXIS(Z_AXIS) + 1]));
#else

8
Marlin/src/lcd/menu/menu.cpp
View File

@ -402,7 +402,7 @@ void scroll_screen(const uint8_t limit, const bool is_menu) {
ui.encoderPosition = 0;
const float diff = planner.steps_to_mm[Z_AXIS] * babystep_increment,
new_probe_offset = zprobe_zoffset + diff,
new_probe_offset = zprobe_offset[Z_AXIS] + diff,
new_offs =
#if ENABLED(BABYSTEP_HOTEND_Z_OFFSET)
do_probe ? new_probe_offset : hotend_offset[Z_AXIS][active_extruder] - diff
@ -414,7 +414,7 @@ void scroll_screen(const uint8_t limit, const bool is_menu) {
babystep.add_steps(Z_AXIS, babystep_increment);
if (do_probe) zprobe_zoffset = new_offs;
if (do_probe) zprobe_offset[Z_AXIS] = new_offs;
#if ENABLED(BABYSTEP_HOTEND_Z_OFFSET)
else hotend_offset[Z_AXIS][active_extruder] = new_offs;
#endif
@ -428,10 +428,10 @@ void scroll_screen(const uint8_t limit, const bool is_menu) {
draw_edit_screen(PSTR(MSG_Z_OFFSET), ftostr43sign(hotend_offset[Z_AXIS][active_extruder]));
else
#endif
draw_edit_screen(PSTR(MSG_ZPROBE_ZOFFSET), ftostr43sign(zprobe_zoffset));
draw_edit_screen(PSTR(MSG_ZPROBE_ZOFFSET), ftostr43sign(zprobe_offset[Z_AXIS]));
#if ENABLED(BABYSTEP_ZPROBE_GFX_OVERLAY)
if (do_probe) _lcd_zoffset_overlay_gfx(zprobe_zoffset);
if (do_probe) _lcd_zoffset_overlay_gfx(zprobe_offset[Z_AXIS]);
#endif
}
}

4
Marlin/src/lcd/menu/menu_bed_corners.cpp
View File

@ -62,10 +62,10 @@ static inline void _lcd_goto_next_corner() {
current_position[Y_AXIS] = Y_MIN_BED + LEVEL_CORNERS_INSET;
break;
case 1:
current_position[X_AXIS] = X_MAX_BED - LEVEL_CORNERS_INSET;
current_position[X_AXIS] = X_MAX_BED - (LEVEL_CORNERS_INSET);
break;
case 2:
current_position[Y_AXIS] = Y_MAX_BED - LEVEL_CORNERS_INSET;
current_position[Y_AXIS] = Y_MAX_BED - (LEVEL_CORNERS_INSET);
break;
case 3:
current_position[X_AXIS] = X_MIN_BED + LEVEL_CORNERS_INSET;

2
Marlin/src/lcd/menu/menu_bed_leveling.cpp
View File

@ -279,7 +279,7 @@ void menu_bed_leveling() {
#if ENABLED(BABYSTEP_ZPROBE_OFFSET)
MENU_ITEM(submenu, MSG_ZPROBE_ZOFFSET, lcd_babystep_zoffset);
#elif HAS_BED_PROBE
MENU_ITEM_EDIT(float52, MSG_ZPROBE_ZOFFSET, &zprobe_zoffset, Z_PROBE_OFFSET_RANGE_MIN, Z_PROBE_OFFSET_RANGE_MAX);
MENU_ITEM_EDIT(float52, MSG_ZPROBE_ZOFFSET, &zprobe_offset[Z_AXIS], Z_PROBE_OFFSET_RANGE_MIN, Z_PROBE_OFFSET_RANGE_MAX);
#endif
#if ENABLED(LEVEL_BED_CORNERS)

2
Marlin/src/lcd/menu/menu_configuration.cpp
View File

@ -347,7 +347,7 @@ void menu_configuration() {
#if ENABLED(BABYSTEP_ZPROBE_OFFSET)
MENU_ITEM(submenu, MSG_ZPROBE_ZOFFSET, lcd_babystep_zoffset);
#elif HAS_BED_PROBE
MENU_ITEM_EDIT(float52, MSG_ZPROBE_ZOFFSET, &zprobe_zoffset, Z_PROBE_OFFSET_RANGE_MIN, Z_PROBE_OFFSET_RANGE_MAX);
MENU_ITEM_EDIT(float52, MSG_ZPROBE_ZOFFSET, &zprobe_offset[Z_AXIS], Z_PROBE_OFFSET_RANGE_MIN, Z_PROBE_OFFSET_RANGE_MAX);
#endif
const bool busy = printer_busy();

39
Marlin/src/module/configuration_store.cpp
View File

@ -37,7 +37,7 @@
*/
// Change EEPROM version if the structure changes
#define EEPROM_VERSION "V69"
#define EEPROM_VERSION "V70"
#define EEPROM_OFFSET 100
// Check the integrity of data offsets.
@ -60,6 +60,8 @@
#include "../HAL/shared/persistent_store_api.h"
#endif
#include "probe.h"
#if HAS_LEVELING
#include "../feature/bedlevel/bedlevel.h"
#endif
@ -78,10 +80,6 @@
#define EEPROM_NUM_SERVOS NUM_SERVO_PLUGS
#endif
#if HAS_BED_PROBE
#include "probe.h"
#endif
#include "../feature/fwretract.h"
#if ENABLED(POWER_LOSS_RECOVERY)
@ -178,7 +176,7 @@ typedef struct SettingsDataStruct {
// HAS_BED_PROBE
//
float zprobe_zoffset;
float zprobe_offset[XYZ];
//
// ABL_PLANAR
@ -615,12 +613,8 @@ void MarlinSettings::postprocess() {
// Probe Z Offset
//
{
_FIELD_TEST(zprobe_zoffset);
#if !HAS_BED_PROBE
const float zprobe_zoffset = 0;
#endif
EEPROM_WRITE(zprobe_zoffset);
_FIELD_TEST(zprobe_offset[Z_AXIS]);
EEPROM_WRITE(zprobe_offset);
}
//
@ -1421,12 +1415,14 @@ void MarlinSettings::postprocess() {
// Probe Z Offset
//
{
_FIELD_TEST(zprobe_zoffset);
_FIELD_TEST(zprobe_offset[Z_AXIS]);
#if !HAS_BED_PROBE
float zprobe_zoffset;
#if HAS_BED_PROBE
float (&zpo)[XYZ] = zprobe_offset;
#else
float zpo[XYZ];
#endif
EEPROM_READ(zprobe_zoffset);
EEPROM_READ(zpo);
}
//
@ -2321,7 +2317,12 @@ void MarlinSettings::reset() {
#endif
#if HAS_BED_PROBE
zprobe_zoffset = Z_PROBE_OFFSET_FROM_EXTRUDER;
#ifndef NOZZLE_TO_PROBE_OFFSET
#define NOZZLE_TO_PROBE_OFFSET { 0, 0, 0 }
#endif
constexpr float dpo[XYZ] = NOZZLE_TO_PROBE_OFFSET;
static_assert(COUNT(dpo) == 3, "NOZZLE_TO_PROBE_OFFSET must contain offsets for X, Y, and Z.");
LOOP_XYZ(a) zprobe_offset[a] = dpo[a];
#endif
//
@ -3070,7 +3071,9 @@ void MarlinSettings::reset() {
say_units(true);
}
CONFIG_ECHO_START();
SERIAL_ECHOLNPAIR(" M851 Z", LINEAR_UNIT(zprobe_zoffset));
SERIAL_ECHOLNPAIR(" M851 X", LINEAR_UNIT(zprobe_offset[X_AXIS]),
" Y", LINEAR_UNIT(zprobe_offset[Y_AXIS]),
" Z", LINEAR_UNIT(zprobe_offset[Z_AXIS]));
#endif
/**

2
Marlin/src/module/delta.cpp
View File

@ -233,7 +233,7 @@ void home_delta() {
// Move all carriages together linearly until an endstop is hit.
destination[Z_AXIS] = (delta_height
#if HAS_BED_PROBE
- zprobe_zoffset
- zprobe_offset[Z_AXIS]
#endif
+ 10);
buffer_line_to_destination(homing_feedrate(X_AXIS));

8
Marlin/src/module/motion.cpp
View File

@ -505,7 +505,7 @@ void restore_feedrate_and_scaling() {
soft_endstop[axis].min = base_min_pos(axis);
soft_endstop[axis].max = (axis == Z_AXIS ? delta_height
#if HAS_BED_PROBE
- zprobe_zoffset
- zprobe_offset[Z_AXIS]
#endif
: base_max_pos(axis));
@ -1340,7 +1340,7 @@ void set_axis_is_at_home(const AxisEnum axis) {
#elif ENABLED(DELTA)
current_position[axis] = (axis == Z_AXIS ? delta_height
#if HAS_BED_PROBE
- zprobe_zoffset
- zprobe_offset[Z_AXIS]
#endif
: base_home_pos(axis));
#else
@ -1354,9 +1354,9 @@ void set_axis_is_at_home(const AxisEnum axis) {
if (axis == Z_AXIS) {
#if HOMING_Z_WITH_PROBE
current_position[Z_AXIS] -= zprobe_zoffset;
current_position[Z_AXIS] -= zprobe_offset[Z_AXIS];
if (DEBUGGING(LEVELING)) DEBUG_ECHOLNPAIR("*** Z HOMED WITH PROBE (Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN) ***\n> zprobe_zoffset = ", zprobe_zoffset);
if (DEBUGGING(LEVELING)) DEBUG_ECHOLNPAIR("*** Z HOMED WITH PROBE (Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN) ***\n> zprobe_offset[Z_AXIS] = ", zprobe_offset[Z_AXIS]);
#else

16
Marlin/src/module/motion.h
View File

@ -30,14 +30,14 @@
#include "../inc/MarlinConfig.h"
#if IS_SCARA
#include "scara.h"
#endif
#if HAS_BED_PROBE
#include "probe.h"
#endif
#if IS_SCARA
#include "scara.h"
#endif
// Axis homed and known-position states
extern uint8_t axis_homed, axis_known_position;
constexpr uint8_t xyz_bits = _BV(X_AXIS) | _BV(Y_AXIS) | _BV(Z_AXIS);
@ -284,7 +284,7 @@ void homeaxis(const AxisEnum axis);
// Return true if the both nozzle and the probe can reach the given point.
// Note: This won't work on SCARA since the probe offset rotates with the arm.
inline bool position_is_reachable_by_probe(const float &rx, const float &ry) {
return position_is_reachable(rx - (X_PROBE_OFFSET_FROM_EXTRUDER), ry - (Y_PROBE_OFFSET_FROM_EXTRUDER))
return position_is_reachable(rx - zprobe_offset[X_AXIS], ry - zprobe_offset[Y_AXIS])
&& position_is_reachable(rx, ry, ABS(MIN_PROBE_EDGE));
}
#endif
@ -313,9 +313,9 @@ void homeaxis(const AxisEnum axis);
* nozzle must be be able to reach +10,-10.
*/
inline bool position_is_reachable_by_probe(const float &rx, const float &ry) {
return position_is_reachable(rx - (X_PROBE_OFFSET_FROM_EXTRUDER), ry - (Y_PROBE_OFFSET_FROM_EXTRUDER))
&& WITHIN(rx, MIN_PROBE_X - slop, MAX_PROBE_X + slop)
&& WITHIN(ry, MIN_PROBE_Y - slop, MAX_PROBE_Y + slop);
return position_is_reachable(rx - zprobe_offset[X_AXIS], ry - zprobe_offset[Y_AXIS])
&& WITHIN(rx, probe_min_x() - slop, probe_max_x() + slop)
&& WITHIN(ry, probe_min_y() - slop, probe_max_y() + slop);
}
#endif

51
Marlin/src/module/probe.cpp
View File

@ -56,7 +56,7 @@
#include "../feature/backlash.h"
#endif
float zprobe_zoffset; // Initialized by settings.load()
float zprobe_offset[XYZ]; // Initialized by settings.load()
#if ENABLED(BLTOUCH)
#include "../feature/bltouch.h"
@ -86,6 +86,43 @@ float zprobe_zoffset; // Initialized by settings.load()
#define DEBUG_OUT ENABLED(DEBUG_LEVELING_FEATURE)
#include "../core/debug_out.h"
float probe_min_x() {
return _MAX(
#if ENABLED(DELTA) || IS_SCARA
PROBE_X_MIN, MESH_MIN_X
#else
(X_MIN_BED) + (MIN_PROBE_EDGE), (X_MIN_POS) + zprobe_offset[X_AXIS]
#endif
);
}
float probe_max_x() {
return _MIN(
#if ENABLED(DELTA) || IS_SCARA
PROBE_X_MAX, MESH_MAX_X
#else
(X_MAX_BED) - (MIN_PROBE_EDGE), (X_MAX_POS) + zprobe_offset[X_AXIS]
#endif
);
}
float probe_min_y() {
return _MAX(
#if ENABLED(DELTA) || IS_SCARA
PROBE_Y_MIN, MESH_MIN_Y
#else
(Y_MIN_BED) + (MIN_PROBE_EDGE), (Y_MIN_POS) + zprobe_offset[Y_AXIS]
#endif
);
}
float probe_max_y() {
return _MIN(
#if ENABLED(DELTA) || IS_SCARA
PROBE_Y_MAX, MESH_MAX_Y
#else
(Y_MAX_BED) - (MIN_PROBE_EDGE), (Y_MAX_POS) + zprobe_offset[Y_AXIS]
#endif
);
}
#if ENABLED(Z_PROBE_SLED)
#ifndef SLED_DOCKING_OFFSET
@ -263,7 +300,7 @@ inline void do_probe_raise(const float z_raise) {
if (DEBUGGING(LEVELING)) DEBUG_ECHOLNPAIR("do_probe_raise(", z_raise, ")");
float z_dest = z_raise;
if (zprobe_zoffset < 0) z_dest -= zprobe_zoffset;
if (zprobe_offset[Z_AXIS] < 0) z_dest -= zprobe_offset[Z_AXIS];
NOMORE(z_dest, Z_MAX_POS);
@ -543,7 +580,7 @@ static float run_z_probe() {
// Stop the probe before it goes too low to prevent damage.
// If Z isn't known then probe to -10mm.
const float z_probe_low_point = TEST(axis_known_position, Z_AXIS) ? -zprobe_zoffset + Z_PROBE_LOW_POINT : -10.0;
const float z_probe_low_point = TEST(axis_known_position, Z_AXIS) ? -zprobe_offset[Z_AXIS] + Z_PROBE_LOW_POINT : -10.0;
// Double-probing does a fast probe followed by a slow probe
#if TOTAL_PROBING == 2
@ -568,7 +605,7 @@ static float run_z_probe() {
// If the nozzle is well over the travel height then
// move down quickly before doing the slow probe
const float z = Z_CLEARANCE_DEPLOY_PROBE + 5.0 + (zprobe_zoffset < 0 ? -zprobe_zoffset : 0);
const float z = Z_CLEARANCE_DEPLOY_PROBE + 5.0 + (zprobe_offset[Z_AXIS] < 0 ? -zprobe_offset[Z_AXIS] : 0);
if (current_position[Z_AXIS] > z) {
// Probe down fast. If the probe never triggered, raise for probe clearance
if (!do_probe_move(z, MMM_TO_MMS(Z_PROBE_SPEED_FAST)))
@ -698,8 +735,8 @@ float probe_at_point(const float &rx, const float &ry, const ProbePtRaise raise_
float nx = rx, ny = ry;
if (probe_relative) {
if (!position_is_reachable_by_probe(rx, ry)) return NAN; // The given position is in terms of the probe
nx -= (X_PROBE_OFFSET_FROM_EXTRUDER); // Get the nozzle position
ny -= (Y_PROBE_OFFSET_FROM_EXTRUDER);
nx -= zprobe_offset[X_AXIS]; // Get the nozzle position
ny -= zprobe_offset[Y_AXIS];
}
else if (!position_is_reachable(nx, ny)) return NAN; // The given position is in terms of the nozzle
@ -720,7 +757,7 @@ float probe_at_point(const float &rx, const float &ry, const ProbePtRaise raise_
float measured_z = NAN;
if (!DEPLOY_PROBE()) {
measured_z = run_z_probe() + zprobe_zoffset;
measured_z = run_z_probe() + zprobe_offset[Z_AXIS];
const bool big_raise = raise_after == PROBE_PT_BIG_RAISE;
if (big_raise || raise_after == PROBE_PT_RAISE)

9
Marlin/src/module/probe.h
View File

@ -28,7 +28,8 @@
#include "../inc/MarlinConfig.h"
#if HAS_BED_PROBE
extern float zprobe_zoffset;
extern float zprobe_offset[XYZ];
bool set_probe_deployed(const bool deploy);
#ifdef Z_AFTER_PROBING
void move_z_after_probing();
@ -45,9 +46,15 @@
#if HAS_HEATED_BED && ENABLED(WAIT_FOR_BED_HEATER)
extern const char msg_wait_for_bed_heating[25];
#endif
float probe_min_x(), probe_max_x(), probe_min_y(), probe_max_y();
#else
constexpr float zprobe_offset[XYZ] = { 0 };
#define DEPLOY_PROBE()
#define STOW_PROBE()
#endif
#if HAS_Z_SERVO_PROBE

19
config/default/Configuration.h
View File

@ -888,11 +888,10 @@
/**
* Z Probe to nozzle (X,Y) offset, relative to (0, 0).
* X and Y offsets must be integers.
*
* In the following example the X and Y offsets are both positive:
* #define X_PROBE_OFFSET_FROM_EXTRUDER 10
* #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
*
* #define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
*
* +-- BACK ---+
* | |
@ -904,10 +903,10 @@
* | |
* O-- FRONT --+
* (0,0)
*
* Specify a Probe position as { X, Y, Z }
*/
#define X_PROBE_OFFSET_FROM_EXTRUDER 10 // X offset: -left +right [of the nozzle]
#define Y_PROBE_OFFSET_FROM_EXTRUDER 10 // Y offset: -front +behind [the nozzle]
#define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle]
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
// Certain types of probes need to stay away from edges
#define MIN_PROBE_EDGE 10
@ -941,7 +940,7 @@
*
* Use these settings to specify the distance (mm) to raise the probe (or
* lower the bed). The values set here apply over and above any (negative)
* probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
* probe Z Offset set with NOZZLE_TO_PROBE_OFFSET, M851, or the LCD.
* Only integer values >= 1 are valid here.
*
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
@ -1199,12 +1198,6 @@
#define GRID_MAX_POINTS_X 3
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
// Set the boundaries for probing (where the probe can reach).
//#define LEFT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define RIGHT_PROBE_BED_POSITION (X_BED_SIZE - (MIN_PROBE_EDGE))
//#define FRONT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define BACK_PROBE_BED_POSITION (Y_BED_SIZE - (MIN_PROBE_EDGE))
// Probe along the Y axis, advancing X after each column
//#define PROBE_Y_FIRST

19
config/examples/3DFabXYZ/Migbot/Configuration.h
View File

@ -894,11 +894,10 @@
/**
* Z Probe to nozzle (X,Y) offset, relative to (0, 0).
* X and Y offsets must be integers.
*
* In the following example the X and Y offsets are both positive:
* #define X_PROBE_OFFSET_FROM_EXTRUDER 10
* #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
*
* #define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
*
* +-- BACK ---+
* | |
@ -910,10 +909,10 @@
* | |
* O-- FRONT --+
* (0,0)
*
* Specify a Probe position as { X, Y, Z }
*/
#define X_PROBE_OFFSET_FROM_EXTRUDER 21 // X offset: -left +right [of the nozzle]
#define Y_PROBE_OFFSET_FROM_EXTRUDER 61 // Y offset: -front +behind [the nozzle]
#define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle]
#define NOZZLE_TO_PROBE_OFFSET { 21, 61, 0 }
// Certain types of probes need to stay away from edges
#define MIN_PROBE_EDGE 10
@ -947,7 +946,7 @@
*
* Use these settings to specify the distance (mm) to raise the probe (or
* lower the bed). The values set here apply over and above any (negative)
* probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
* probe Z Offset set with NOZZLE_TO_PROBE_OFFSET, M851, or the LCD.
* Only integer values >= 1 are valid here.
*
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
@ -1205,12 +1204,6 @@
#define GRID_MAX_POINTS_X 3
#define GRID_MAX_POINTS_Y 4
// Set the boundaries for probing (where the probe can reach).
#define LEFT_PROBE_BED_POSITION X_PROBE_OFFSET_FROM_EXTRUDER
#define RIGHT_PROBE_BED_POSITION (X_BED_SIZE - (X_PROBE_OFFSET_FROM_EXTRUDER) + MIN_PROBE_EDGE)
#define FRONT_PROBE_BED_POSITION Y_PROBE_OFFSET_FROM_EXTRUDER
#define BACK_PROBE_BED_POSITION (Y_BED_SIZE - (MIN_PROBE_EDGE))
// Probe along the Y axis, advancing X after each column
//#define PROBE_Y_FIRST

19
config/examples/ADIMLab/Gantry v1/Configuration.h
View File

@ -888,11 +888,10 @@
/**
* Z Probe to nozzle (X,Y) offset, relative to (0, 0).
* X and Y offsets must be integers.
*
* In the following example the X and Y offsets are both positive:
* #define X_PROBE_OFFSET_FROM_EXTRUDER 10
* #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
*
* #define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
*
* +-- BACK ---+
* | |
@ -904,10 +903,10 @@
* | |
* O-- FRONT --+
* (0,0)
*
* Specify a Probe position as { X, Y, Z }
*/
#define X_PROBE_OFFSET_FROM_EXTRUDER 10 // X offset: -left +right [of the nozzle]
#define Y_PROBE_OFFSET_FROM_EXTRUDER 10 // Y offset: -front +behind [the nozzle]
#define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle]
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
// Certain types of probes need to stay away from edges
#define MIN_PROBE_EDGE 10
@ -941,7 +940,7 @@
*
* Use these settings to specify the distance (mm) to raise the probe (or
* lower the bed). The values set here apply over and above any (negative)
* probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
* probe Z Offset set with NOZZLE_TO_PROBE_OFFSET, M851, or the LCD.
* Only integer values >= 1 are valid here.
*
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
@ -1200,12 +1199,6 @@
#define GRID_MAX_POINTS_X 3
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
// Set the boundaries for probing (where the probe can reach).
//#define LEFT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define RIGHT_PROBE_BED_POSITION (X_BED_SIZE - (MIN_PROBE_EDGE))
//#define FRONT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define BACK_PROBE_BED_POSITION (Y_BED_SIZE - (MIN_PROBE_EDGE))
// Probe along the Y axis, advancing X after each column
//#define PROBE_Y_FIRST

19
config/examples/ADIMLab/Gantry v2/Configuration.h
View File

@ -888,11 +888,10 @@
/**
* Z Probe to nozzle (X,Y) offset, relative to (0, 0).
* X and Y offsets must be integers.
*
* In the following example the X and Y offsets are both positive:
* #define X_PROBE_OFFSET_FROM_EXTRUDER 10
* #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
*
* #define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
*
* +-- BACK ---+
* | |
@ -904,10 +903,10 @@
* | |
* O-- FRONT --+
* (0,0)
*
* Specify a Probe position as { X, Y, Z }
*/
#define X_PROBE_OFFSET_FROM_EXTRUDER 10 // X offset: -left +right [of the nozzle]
#define Y_PROBE_OFFSET_FROM_EXTRUDER 10 // Y offset: -front +behind [the nozzle]
#define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle]
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
// Certain types of probes need to stay away from edges
#define MIN_PROBE_EDGE 10
@ -941,7 +940,7 @@
*
* Use these settings to specify the distance (mm) to raise the probe (or
* lower the bed). The values set here apply over and above any (negative)
* probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
* probe Z Offset set with NOZZLE_TO_PROBE_OFFSET, M851, or the LCD.
* Only integer values >= 1 are valid here.
*
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
@ -1200,12 +1199,6 @@
#define GRID_MAX_POINTS_X 3
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
// Set the boundaries for probing (where the probe can reach).
//#define LEFT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define RIGHT_PROBE_BED_POSITION (X_BED_SIZE - (MIN_PROBE_EDGE))
//#define FRONT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define BACK_PROBE_BED_POSITION (Y_BED_SIZE - (MIN_PROBE_EDGE))
// Probe along the Y axis, advancing X after each column
//#define PROBE_Y_FIRST

19
config/examples/AlephObjects/TAZ4/Configuration.h
View File

@ -908,11 +908,10 @@
/**
* Z Probe to nozzle (X,Y) offset, relative to (0, 0).
* X and Y offsets must be integers.
*
* In the following example the X and Y offsets are both positive:
* #define X_PROBE_OFFSET_FROM_EXTRUDER 10
* #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
*
* #define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
*
* +-- BACK ---+
* | |
@ -924,10 +923,10 @@
* | |
* O-- FRONT --+
* (0,0)
*
* Specify a Probe position as { X, Y, Z }
*/
#define X_PROBE_OFFSET_FROM_EXTRUDER -25 // X offset: -left +right [of the nozzle]
#define Y_PROBE_OFFSET_FROM_EXTRUDER -29 // Y offset: -front +behind [the nozzle]
#define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 // Z offset: -below +above [the nozzle]
#define NOZZLE_TO_PROBE_OFFSET { -25, -29, -12.35 }
// Certain types of probes need to stay away from edges
#define MIN_PROBE_EDGE 10
@ -961,7 +960,7 @@
*
* Use these settings to specify the distance (mm) to raise the probe (or
* lower the bed). The values set here apply over and above any (negative)
* probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
* probe Z Offset set with NOZZLE_TO_PROBE_OFFSET, M851, or the LCD.
* Only integer values >= 1 are valid here.
*
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
@ -1219,12 +1218,6 @@
#define GRID_MAX_POINTS_X 3
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
// Set the boundaries for probing (where the probe can reach).
//#define LEFT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define RIGHT_PROBE_BED_POSITION (X_BED_SIZE - (MIN_PROBE_EDGE))
//#define FRONT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define BACK_PROBE_BED_POSITION (Y_BED_SIZE - (MIN_PROBE_EDGE))
// Probe along the Y axis, advancing X after each column
//#define PROBE_Y_FIRST

21
config/examples/Alfawise/U20-bltouch/Configuration.h
View File

@ -953,11 +953,10 @@
/**
* Z Probe to nozzle (X,Y) offset, relative to (0, 0).
* X and Y offsets must be integers.
*
* In the following example the X and Y offsets are both positive:
* #define X_PROBE_OFFSET_FROM_EXTRUDER 10
* #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
*
* #define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
*
* +-- BACK ---+
* | |
@ -969,10 +968,10 @@
* | |
* O-- FRONT --+
* (0,0)
*
* Specify a Probe position as { X, Y, Z }
*/
#define X_PROBE_OFFSET_FROM_EXTRUDER -35 // X offset: -left +right [of the nozzle]
#define Y_PROBE_OFFSET_FROM_EXTRUDER -6 // Y offset: -front +behind [the nozzle]
#define Z_PROBE_OFFSET_FROM_EXTRUDER -0.5 // Z offset: -below +above [the nozzle]
#define NOZZLE_TO_PROBE_OFFSET { -35, -6, -0.5 }
// Certain types of probes need to stay away from edges
#define MIN_PROBE_EDGE 10
@ -1006,7 +1005,7 @@
*
* Use these settings to specify the distance (mm) to raise the probe (or
* lower the bed). The values set here apply over and above any (negative)
* probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
* probe Z Offset set with NOZZLE_TO_PROBE_OFFSET, M851, or the LCD.
* Only integer values >= 1 are valid here.
*
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
@ -1278,12 +1277,6 @@
#define GRID_MAX_POINTS_X 4
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
// Set the boundaries for probing (where the probe can reach).
//#define LEFT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define RIGHT_PROBE_BED_POSITION (X_BED_SIZE - (MIN_PROBE_EDGE))
//#define FRONT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define BACK_PROBE_BED_POSITION (Y_BED_SIZE - (MIN_PROBE_EDGE))
// Probe along the Y axis, advancing X after each column
//#define PROBE_Y_FIRST
@ -1404,7 +1397,7 @@
#if ENABLED(Z_SAFE_HOMING)
#define Z_SAFE_HOMING_X_POINT ((X_BED_SIZE) / 2) // X point for Z homing when homing all axes (G28).
//#define Z_SAFE_HOMING_Y_POINT ((Y_BED_SIZE) / 2) // Y point for Z homing when homing all axes (G28).
#define Z_SAFE_HOMING_Y_POINT MIN_PROBE_Y
#define Z_SAFE_HOMING_Y_POINT 4
#endif
// Homing speeds (mm/m)

21
config/examples/Alfawise/U20/Configuration.h
View File

@ -953,11 +953,10 @@
/**
* Z Probe to nozzle (X,Y) offset, relative to (0, 0).
* X and Y offsets must be integers.
*
* In the following example the X and Y offsets are both positive:
* #define X_PROBE_OFFSET_FROM_EXTRUDER 10
* #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
*
* #define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
*
* +-- BACK ---+
* | |
@ -969,10 +968,10 @@
* | |
* O-- FRONT --+
* (0,0)
*
* Specify a Probe position as { X, Y, Z }
*/
#define X_PROBE_OFFSET_FROM_EXTRUDER 10 // X offset: -left +right [of the nozzle]
#define Y_PROBE_OFFSET_FROM_EXTRUDER 10 // Y offset: -front +behind [the nozzle]
#define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle]
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
// Certain types of probes need to stay away from edges
#define MIN_PROBE_EDGE 10
@ -1006,7 +1005,7 @@
*
* Use these settings to specify the distance (mm) to raise the probe (or
* lower the bed). The values set here apply over and above any (negative)
* probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
* probe Z Offset set with NOZZLE_TO_PROBE_OFFSET, M851, or the LCD.
* Only integer values >= 1 are valid here.
*
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
@ -1278,12 +1277,6 @@
#define GRID_MAX_POINTS_X 3
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
// Set the boundaries for probing (where the probe can reach).
//#define LEFT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define RIGHT_PROBE_BED_POSITION (X_BED_SIZE - (MIN_PROBE_EDGE))
//#define FRONT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define BACK_PROBE_BED_POSITION (Y_BED_SIZE - (MIN_PROBE_EDGE))
// Probe along the Y axis, advancing X after each column
//#define PROBE_Y_FIRST
@ -1403,7 +1396,7 @@
#if ENABLED(Z_SAFE_HOMING)
#define Z_SAFE_HOMING_X_POINT ((X_BED_SIZE) / 2) // X point for Z homing when homing all axes (G28).
#define Z_SAFE_HOMING_Y_POINT ((Y_BED_SIZE) / 2) // Y point for Z homing when homing all axes (G28).
#define Z_SAFE_HOMING_Y_POINT 4 // Y point for Z homing when homing all axes (G28).
#endif
// Homing speeds (mm/m)

19
config/examples/AliExpress/CL-260/Configuration.h
View File

@ -888,11 +888,10 @@
/**
* Z Probe to nozzle (X,Y) offset, relative to (0, 0).
* X and Y offsets must be integers.
*
* In the following example the X and Y offsets are both positive:
* #define X_PROBE_OFFSET_FROM_EXTRUDER 10
* #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
*
* #define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
*
* +-- BACK ---+
* | |
@ -904,10 +903,10 @@
* | |
* O-- FRONT --+
* (0,0)
*
* Specify a Probe position as { X, Y, Z }
*/
#define X_PROBE_OFFSET_FROM_EXTRUDER 10 // X offset: -left +right [of the nozzle]
#define Y_PROBE_OFFSET_FROM_EXTRUDER 10 // Y offset: -front +behind [the nozzle]
#define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle]
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
// Certain types of probes need to stay away from edges
#define MIN_PROBE_EDGE 10
@ -941,7 +940,7 @@
*
* Use these settings to specify the distance (mm) to raise the probe (or
* lower the bed). The values set here apply over and above any (negative)
* probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
* probe Z Offset set with NOZZLE_TO_PROBE_OFFSET, M851, or the LCD.
* Only integer values >= 1 are valid here.
*
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
@ -1199,12 +1198,6 @@
#define GRID_MAX_POINTS_X 3
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
// Set the boundaries for probing (where the probe can reach).
//#define LEFT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define RIGHT_PROBE_BED_POSITION (X_BED_SIZE - (MIN_PROBE_EDGE))
//#define FRONT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define BACK_PROBE_BED_POSITION (Y_BED_SIZE - (MIN_PROBE_EDGE))
// Probe along the Y axis, advancing X after each column
//#define PROBE_Y_FIRST

19
config/examples/AliExpress/UM2pExt/Configuration.h
View File

@ -899,11 +899,10 @@
/**
* Z Probe to nozzle (X,Y) offset, relative to (0, 0).
* X and Y offsets must be integers.
*
* In the following example the X and Y offsets are both positive:
* #define X_PROBE_OFFSET_FROM_EXTRUDER 10
* #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
*
* #define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
*
* +-- BACK ---+
* | |
@ -915,10 +914,10 @@
* | |
* O-- FRONT --+
* (0,0)
*
* Specify a Probe position as { X, Y, Z }
*/
#define X_PROBE_OFFSET_FROM_EXTRUDER 10 // X offset: -left +right [of the nozzle]
#define Y_PROBE_OFFSET_FROM_EXTRUDER 10 // Y offset: -front +behind [the nozzle]
#define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle]
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
// Certain types of probes need to stay away from edges
#define MIN_PROBE_EDGE 10
@ -952,7 +951,7 @@
*
* Use these settings to specify the distance (mm) to raise the probe (or
* lower the bed). The values set here apply over and above any (negative)
* probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
* probe Z Offset set with NOZZLE_TO_PROBE_OFFSET, M851, or the LCD.
* Only integer values >= 1 are valid here.
*
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
@ -1210,12 +1209,6 @@
#define GRID_MAX_POINTS_X 3
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
// Set the boundaries for probing (where the probe can reach).
//#define LEFT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define RIGHT_PROBE_BED_POSITION (X_BED_SIZE - (MIN_PROBE_EDGE))
//#define FRONT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define BACK_PROBE_BED_POSITION (Y_BED_SIZE - (MIN_PROBE_EDGE))
// Probe along the Y axis, advancing X after each column
//#define PROBE_Y_FIRST

19
config/examples/Anet/A2/Configuration.h
View File

@ -888,11 +888,10 @@
/**
* Z Probe to nozzle (X,Y) offset, relative to (0, 0).
* X and Y offsets must be integers.
*
* In the following example the X and Y offsets are both positive:
* #define X_PROBE_OFFSET_FROM_EXTRUDER 10
* #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
*
* #define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
*
* +-- BACK ---+
* | |
@ -904,10 +903,10 @@
* | |
* O-- FRONT --+
* (0,0)
*
* Specify a Probe position as { X, Y, Z }
*/
//#define X_PROBE_OFFSET_FROM_EXTRUDER 10 // X offset: -left +right [of the nozzle]
//#define Y_PROBE_OFFSET_FROM_EXTRUDER 10 // Y offset: -front +behind [the nozzle]
//#define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle]
//#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
// Certain types of probes need to stay away from edges
//#define MIN_PROBE_EDGE 10
@ -941,7 +940,7 @@
*
* Use these settings to specify the distance (mm) to raise the probe (or
* lower the bed). The values set here apply over and above any (negative)
* probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
* probe Z Offset set with NOZZLE_TO_PROBE_OFFSET, M851, or the LCD.
* Only integer values >= 1 are valid here.
*
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
@ -1199,12 +1198,6 @@
#define GRID_MAX_POINTS_X 3
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
// Set the boundaries for probing (where the probe can reach).
//#define LEFT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define RIGHT_PROBE_BED_POSITION (X_BED_SIZE - (MIN_PROBE_EDGE))
//#define FRONT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define BACK_PROBE_BED_POSITION (Y_BED_SIZE - (MIN_PROBE_EDGE))
// Probe along the Y axis, advancing X after each column
//#define PROBE_Y_FIRST

19
config/examples/Anet/A2plus/Configuration.h
View File

@ -888,11 +888,10 @@
/**
* Z Probe to nozzle (X,Y) offset, relative to (0, 0).
* X and Y offsets must be integers.
*
* In the following example the X and Y offsets are both positive:
* #define X_PROBE_OFFSET_FROM_EXTRUDER 10
* #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
*
* #define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
*
* +-- BACK ---+
* | |
@ -904,10 +903,10 @@
* | |
* O-- FRONT --+
* (0,0)
*
* Specify a Probe position as { X, Y, Z }
*/
//#define X_PROBE_OFFSET_FROM_EXTRUDER 10 // X offset: -left +right [of the nozzle]
//#define Y_PROBE_OFFSET_FROM_EXTRUDER 10 // Y offset: -front +behind [the nozzle]
//#define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle]
//#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
// Certain types of probes need to stay away from edges
//#define MIN_PROBE_EDGE 10
@ -941,7 +940,7 @@
*
* Use these settings to specify the distance (mm) to raise the probe (or
* lower the bed). The values set here apply over and above any (negative)
* probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
* probe Z Offset set with NOZZLE_TO_PROBE_OFFSET, M851, or the LCD.
* Only integer values >= 1 are valid here.
*
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
@ -1199,12 +1198,6 @@
#define GRID_MAX_POINTS_X 3
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
// Set the boundaries for probing (where the probe can reach).
//#define LEFT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define RIGHT_PROBE_BED_POSITION (X_BED_SIZE - (MIN_PROBE_EDGE))
//#define FRONT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define BACK_PROBE_BED_POSITION (Y_BED_SIZE - (MIN_PROBE_EDGE))
// Probe along the Y axis, advancing X after each column
//#define PROBE_Y_FIRST

59
config/examples/Anet/A6/Configuration.h
View File

@ -935,11 +935,10 @@
/**
* Z Probe to nozzle (X,Y) offset, relative to (0, 0).
* X and Y offsets must be integers.
*
* In the following example the X and Y offsets are both positive:
* #define X_PROBE_OFFSET_FROM_EXTRUDER 10
* #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
*
* #define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
*
* +-- BACK ---+
* | |
@ -951,31 +950,23 @@
* | |
* O-- FRONT --+
* (0,0)
*
* Specify a Probe position as { X, Y, Z }
*/
//#define X_PROBE_OFFSET_FROM_EXTRUDER 10 // X offset: -left +right [of the nozzle]
//#define Y_PROBE_OFFSET_FROM_EXTRUDER 10 // Y offset: -front +behind [the nozzle]
//#define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle]
//#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
// ANET A8: FRONT-MOUNTED SENSOR WITH 3D PRINTED MOUNT
//#define X_PROBE_OFFSET_FROM_EXTRUDER -28 // X offset: -left +right [of the nozzle]
//#define Y_PROBE_OFFSET_FROM_EXTRUDER -45 // Y offset: -front +behind [the nozzle]
//#define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle]
//#define NOZZLE_TO_PROBE_OFFSET { -28, -45, 0 }
// THESE ARE FOR THE OFFICIAL ANET REAR-MOUNTED SENSOR
//#define X_PROBE_OFFSET_FROM_EXTRUDER -1 // X offset: -left +right [of the nozzle]
//#define Y_PROBE_OFFSET_FROM_EXTRUDER 3 // Y offset: -front +behind [the nozzle]
//#define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle]
//#define NOZZLE_TO_PROBE_OFFSET { -1, 3, 0 }
// ANET A6 with BLTouch/3D-Touch mounted right to the nozzle
#define X_PROBE_OFFSET_FROM_EXTRUDER 39 // X offset: -left +right [of the nozzle]
#define Y_PROBE_OFFSET_FROM_EXTRUDER 0 // Y offset: -front +behind [the nozzle]
#define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle]
#define NOZZLE_TO_PROBE_OFFSET { 39, 0, 0 }
//ANET A6 with BLTouch/3D-Touch betwen Fan and Belt
// (mount: https://github.com/ralf-e/ANET_A6_modifications/tree/master/A6_X-Axis)
//#define X_PROBE_OFFSET_FROM_EXTRUDER -30 // X offset: -left +right [of the nozzle]
//#define Y_PROBE_OFFSET_FROM_EXTRUDER 15 // Y offset: -front +behind [the nozzle]
//#define Z_PROBE_OFFSET_FROM_EXTRUDER 0.75 // Z offset: -below +above [the nozzle]
//#define NOZZLE_TO_PROBE_OFFSET { -30, 15, 0.75 }
// Certain types of probes need to stay away from edges
#define MIN_PROBE_EDGE 10
@ -1010,7 +1001,7 @@
*
* Use these settings to specify the distance (mm) to raise the probe (or
* lower the bed). The values set here apply over and above any (negative)
* probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
* probe Z Offset set with NOZZLE_TO_PROBE_OFFSET, M851, or the LCD.
* Only integer values >= 1 are valid here.
*
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
@ -1312,36 +1303,6 @@
#define GRID_MAX_POINTS_X 4
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
// Set the boundaries for probing (where the probe can reach).
//#define LEFT_PROBE_BED_POSITION 15
//#define RIGHT_PROBE_BED_POSITION (X_BED_SIZE - 15)
//#define FRONT_PROBE_BED_POSITION 15
//#define BACK_PROBE_BED_POSITION (Y_BED_SIZE - 15)
// ANET A6
//#define LEFT_PROBE_BED_POSITION 20
//#define RIGHT_PROBE_BED_POSITION 190
//#define FRONT_PROBE_BED_POSITION 20
//#define BACK_PROBE_BED_POSITION 190
// ANET A6 BLTOUCH right (39mm) to the nozzle
//#define LEFT_PROBE_BED_POSITION 36
//#define RIGHT_PROBE_BED_POSITION 190
//#define FRONT_PROBE_BED_POSITION 20
//#define BACK_PROBE_BED_POSITION 190
// ANET A6 with new X-Axis and modded Y-Axis
//#define LEFT_PROBE_BED_POSITION 20
//#define RIGHT_PROBE_BED_POSITION 205
//#define FRONT_PROBE_BED_POSITION 20
//#define BACK_PROBE_BED_POSITION 205
// ANET A6 with new X-Axis and modded Y-Axis, X0/Y0 front left bed edge
//#define LEFT_PROBE_BED_POSITION 20
//#define RIGHT_PROBE_BED_POSITION 194
//#define FRONT_PROBE_BED_POSITION 20
//#define BACK_PROBE_BED_POSITION 194
// Probe along the Y axis, advancing X after each column
//#define PROBE_Y_FIRST

19
config/examples/Anet/A8/Configuration.h
View File

@ -901,11 +901,10 @@
/**
* Z Probe to nozzle (X,Y) offset, relative to (0, 0).
* X and Y offsets must be integers.
*
* In the following example the X and Y offsets are both positive:
* #define X_PROBE_OFFSET_FROM_EXTRUDER 10
* #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
*
* #define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
*
* +-- BACK ---+
* | |
@ -917,10 +916,10 @@
* | |
* O-- FRONT --+
* (0,0)
*
* Specify a Probe position as { X, Y, Z }
*/
#define X_PROBE_OFFSET_FROM_EXTRUDER 0 // X offset: -left +right [of the nozzle]
#define Y_PROBE_OFFSET_FROM_EXTRUDER 0 // Y offset: -front +behind [the nozzle]
#define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle]
#define NOZZLE_TO_PROBE_OFFSET { 0, 0, 0 }
// Certain types of probes need to stay away from edges
#define MIN_PROBE_EDGE 10
@ -954,7 +953,7 @@
*
* Use these settings to specify the distance (mm) to raise the probe (or
* lower the bed). The values set here apply over and above any (negative)
* probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
* probe Z Offset set with NOZZLE_TO_PROBE_OFFSET, M851, or the LCD.
* Only integer values >= 1 are valid here.
*
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
@ -1212,12 +1211,6 @@
#define GRID_MAX_POINTS_X 3
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
// Set the boundaries for probing (where the probe can reach).
//#define LEFT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define RIGHT_PROBE_BED_POSITION (X_BED_SIZE - (MIN_PROBE_EDGE))
//#define FRONT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define BACK_PROBE_BED_POSITION (Y_BED_SIZE - (MIN_PROBE_EDGE))
// Probe along the Y axis, advancing X after each column
//#define PROBE_Y_FIRST

19
config/examples/Anet/A8plus/Configuration.h
View File

@ -899,11 +899,10 @@
/**
* Z Probe to nozzle (X,Y) offset, relative to (0, 0).
* X and Y offsets must be integers.
*
* In the following example the X and Y offsets are both positive:
* #define X_PROBE_OFFSET_FROM_EXTRUDER 10
* #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
*
* #define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
*
* +-- BACK ---+
* | |
@ -915,10 +914,10 @@
* | |
* O-- FRONT --+
* (0,0)
*
* Specify a Probe position as { X, Y, Z }
*/
#define X_PROBE_OFFSET_FROM_EXTRUDER 10 // X offset: -left +right [of the nozzle]
#define Y_PROBE_OFFSET_FROM_EXTRUDER 10 // Y offset: -front +behind [the nozzle]
#define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle]
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
// Certain types of probes need to stay away from edges
#define MIN_PROBE_EDGE 10
@ -952,7 +951,7 @@
*
* Use these settings to specify the distance (mm) to raise the probe (or
* lower the bed). The values set here apply over and above any (negative)
* probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
* probe Z Offset set with NOZZLE_TO_PROBE_OFFSET, M851, or the LCD.
* Only integer values >= 1 are valid here.
*
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
@ -1210,12 +1209,6 @@
#define GRID_MAX_POINTS_X 3
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
// Set the boundaries for probing (where the probe can reach).
//#define LEFT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define RIGHT_PROBE_BED_POSITION (X_BED_SIZE - (MIN_PROBE_EDGE))
//#define FRONT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define BACK_PROBE_BED_POSITION (Y_BED_SIZE - (MIN_PROBE_EDGE))
// Probe along the Y axis, advancing X after each column
//#define PROBE_Y_FIRST

19
config/examples/Anet/E16/Configuration.h
View File

@ -900,11 +900,10 @@
/**
* Z Probe to nozzle (X,Y) offset, relative to (0, 0).
* X and Y offsets must be integers.
*
* In the following example the X and Y offsets are both positive:
* #define X_PROBE_OFFSET_FROM_EXTRUDER 10
* #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
*
* #define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
*
* +-- BACK ---+
* | |
@ -916,10 +915,10 @@
* | |
* O-- FRONT --+
* (0,0)
*
* Specify a Probe position as { X, Y, Z }
*/
#define X_PROBE_OFFSET_FROM_EXTRUDER 10 // X offset: -left +right [of the nozzle]
#define Y_PROBE_OFFSET_FROM_EXTRUDER 10 // Y offset: -front +behind [the nozzle]
#define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle]
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
// Certain types of probes need to stay away from edges
#define MIN_PROBE_EDGE 10
@ -953,7 +952,7 @@
*
* Use these settings to specify the distance (mm) to raise the probe (or
* lower the bed). The values set here apply over and above any (negative)
* probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
* probe Z Offset set with NOZZLE_TO_PROBE_OFFSET, M851, or the LCD.
* Only integer values >= 1 are valid here.
*
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
@ -1211,12 +1210,6 @@
#define GRID_MAX_POINTS_X 3
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
// Set the boundaries for probing (where the probe can reach).
//#define LEFT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define RIGHT_PROBE_BED_POSITION (X_BED_SIZE - (MIN_PROBE_EDGE))
//#define FRONT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define BACK_PROBE_BED_POSITION (Y_BED_SIZE - (MIN_PROBE_EDGE))
// Probe along the Y axis, advancing X after each column
//#define PROBE_Y_FIRST

19
config/examples/AnyCubic/i3/Configuration.h
View File

@ -898,11 +898,10 @@
/**
* Z Probe to nozzle (X,Y) offset, relative to (0, 0).
* X and Y offsets must be integers.
*
* In the following example the X and Y offsets are both positive:
* #define X_PROBE_OFFSET_FROM_EXTRUDER 10
* #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
*
* #define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
*
* +-- BACK ---+
* | |
@ -914,10 +913,10 @@
* | |
* O-- FRONT --+
* (0,0)
*
* Specify a Probe position as { X, Y, Z }
*/
#define X_PROBE_OFFSET_FROM_EXTRUDER 75 // X offset: -left +right [of the nozzle]
#define Y_PROBE_OFFSET_FROM_EXTRUDER 5 // Y offset: -front +behind [the nozzle]
#define Z_PROBE_OFFSET_FROM_EXTRUDER -2 // Z offset: -below +above [the nozzle]
#define NOZZLE_TO_PROBE_OFFSET { 75, 5, -2 }
// Certain types of probes need to stay away from edges
#define MIN_PROBE_EDGE 10
@ -951,7 +950,7 @@
*
* Use these settings to specify the distance (mm) to raise the probe (or
* lower the bed). The values set here apply over and above any (negative)
* probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
* probe Z Offset set with NOZZLE_TO_PROBE_OFFSET, M851, or the LCD.
* Only integer values >= 1 are valid here.
*
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
@ -1209,12 +1208,6 @@
#define GRID_MAX_POINTS_X 3
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
// Set the boundaries for probing (where the probe can reach).
//#define LEFT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define RIGHT_PROBE_BED_POSITION (X_BED_SIZE - (MIN_PROBE_EDGE))
//#define FRONT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define BACK_PROBE_BED_POSITION (Y_BED_SIZE - (MIN_PROBE_EDGE))
// Probe along the Y axis, advancing X after each column
//#define PROBE_Y_FIRST

19
config/examples/ArmEd/Configuration.h
View File

@ -889,11 +889,10 @@
/**
* Z Probe to nozzle (X,Y) offset, relative to (0, 0).
* X and Y offsets must be integers.
*
* In the following example the X and Y offsets are both positive:
* #define X_PROBE_OFFSET_FROM_EXTRUDER 10
* #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
*
* #define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
*
* +-- BACK ---+
* | |
@ -905,10 +904,10 @@
* | |
* O-- FRONT --+
* (0,0)
*
* Specify a Probe position as { X, Y, Z }
*/
#define X_PROBE_OFFSET_FROM_EXTRUDER 10 // X offset: -left +right [of the nozzle]
#define Y_PROBE_OFFSET_FROM_EXTRUDER 10 // Y offset: -front +behind [the nozzle]
#define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle]
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
// Certain types of probes need to stay away from edges
#define MIN_PROBE_EDGE 10
@ -942,7 +941,7 @@
*
* Use these settings to specify the distance (mm) to raise the probe (or
* lower the bed). The values set here apply over and above any (negative)
* probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
* probe Z Offset set with NOZZLE_TO_PROBE_OFFSET, M851, or the LCD.
* Only integer values >= 1 are valid here.
*
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
@ -1200,12 +1199,6 @@
#define GRID_MAX_POINTS_X 3
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
// Set the boundaries for probing (where the probe can reach).
//#define LEFT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define RIGHT_PROBE_BED_POSITION (X_BED_SIZE - (MIN_PROBE_EDGE))
//#define FRONT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define BACK_PROBE_BED_POSITION (Y_BED_SIZE - (MIN_PROBE_EDGE))
// Probe along the Y axis, advancing X after each column
//#define PROBE_Y_FIRST

19
config/examples/Azteeg/X5GT/Configuration.h
View File

@ -888,11 +888,10 @@
/**
* Z Probe to nozzle (X,Y) offset, relative to (0, 0).
* X and Y offsets must be integers.
*
* In the following example the X and Y offsets are both positive:
* #define X_PROBE_OFFSET_FROM_EXTRUDER 10
* #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
*
* #define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
*
* +-- BACK ---+
* | |
@ -904,10 +903,10 @@
* | |
* O-- FRONT --+
* (0,0)
*
* Specify a Probe position as { X, Y, Z }
*/
#define X_PROBE_OFFSET_FROM_EXTRUDER 10 // X offset: -left +right [of the nozzle]
#define Y_PROBE_OFFSET_FROM_EXTRUDER 10 // Y offset: -front +behind [the nozzle]
#define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle]
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
// Certain types of probes need to stay away from edges
#define MIN_PROBE_EDGE 10
@ -941,7 +940,7 @@
*
* Use these settings to specify the distance (mm) to raise the probe (or
* lower the bed). The values set here apply over and above any (negative)
* probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
* probe Z Offset set with NOZZLE_TO_PROBE_OFFSET, M851, or the LCD.
* Only integer values >= 1 are valid here.
*
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
@ -1199,12 +1198,6 @@
#define GRID_MAX_POINTS_X 3
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
// Set the boundaries for probing (where the probe can reach).
//#define LEFT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define RIGHT_PROBE_BED_POSITION (X_BED_SIZE - (MIN_PROBE_EDGE))
//#define FRONT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define BACK_PROBE_BED_POSITION (Y_BED_SIZE - (MIN_PROBE_EDGE))
// Probe along the Y axis, advancing X after each column
//#define PROBE_Y_FIRST

19
config/examples/BIBO/TouchX/cyclops/Configuration.h
View File

@ -888,11 +888,10 @@
/**
* Z Probe to nozzle (X,Y) offset, relative to (0, 0).
* X and Y offsets must be integers.
*
* In the following example the X and Y offsets are both positive:
* #define X_PROBE_OFFSET_FROM_EXTRUDER 10
* #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
*
* #define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
*
* +-- BACK ---+
* | |
@ -904,10 +903,10 @@
* | |
* O-- FRONT --+
* (0,0)
*
* Specify a Probe position as { X, Y, Z }
*/
#define X_PROBE_OFFSET_FROM_EXTRUDER 10 // X offset: -left +right [of the nozzle]
#define Y_PROBE_OFFSET_FROM_EXTRUDER 10 // Y offset: -front +behind [the nozzle]
#define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle]
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
// Certain types of probes need to stay away from edges
#define MIN_PROBE_EDGE 10
@ -941,7 +940,7 @@
*
* Use these settings to specify the distance (mm) to raise the probe (or
* lower the bed). The values set here apply over and above any (negative)
* probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
* probe Z Offset set with NOZZLE_TO_PROBE_OFFSET, M851, or the LCD.
* Only integer values >= 1 are valid here.
*
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
@ -1199,12 +1198,6 @@
#define GRID_MAX_POINTS_X 3
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
// Set the boundaries for probing (where the probe can reach).
//#define LEFT_PROBE_BED_POSITION 15
//#define RIGHT_PROBE_BED_POSITION 170
//#define FRONT_PROBE_BED_POSITION 20
//#define BACK_PROBE_BED_POSITION 170
// Probe along the Y axis, advancing X after each column
//#define PROBE_Y_FIRST

19
config/examples/BIBO/TouchX/default/Configuration.h
View File

@ -888,11 +888,10 @@
/**
* Z Probe to nozzle (X,Y) offset, relative to (0, 0).
* X and Y offsets must be integers.
*
* In the following example the X and Y offsets are both positive:
* #define X_PROBE_OFFSET_FROM_EXTRUDER 10
* #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
*
* #define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
*
* +-- BACK ---+
* | |
@ -904,10 +903,10 @@
* | |
* O-- FRONT --+
* (0,0)
*
* Specify a Probe position as { X, Y, Z }
*/
#define X_PROBE_OFFSET_FROM_EXTRUDER 10 // X offset: -left +right [of the nozzle]
#define Y_PROBE_OFFSET_FROM_EXTRUDER 10 // Y offset: -front +behind [the nozzle]
#define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle]
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
// Certain types of probes need to stay away from edges
#define MIN_PROBE_EDGE 10
@ -941,7 +940,7 @@
*
* Use these settings to specify the distance (mm) to raise the probe (or
* lower the bed). The values set here apply over and above any (negative)
* probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
* probe Z Offset set with NOZZLE_TO_PROBE_OFFSET, M851, or the LCD.
* Only integer values >= 1 are valid here.
*
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
@ -1199,12 +1198,6 @@
#define GRID_MAX_POINTS_X 3
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
// Set the boundaries for probing (where the probe can reach).
//#define LEFT_PROBE_BED_POSITION 15
//#define RIGHT_PROBE_BED_POSITION 170
//#define FRONT_PROBE_BED_POSITION 20
//#define BACK_PROBE_BED_POSITION 170
// Probe along the Y axis, advancing X after each column
//#define PROBE_Y_FIRST

19
config/examples/BQ/Hephestos/Configuration.h
View File

@ -876,11 +876,10 @@
/**
* Z Probe to nozzle (X,Y) offset, relative to (0, 0).
* X and Y offsets must be integers.
*
* In the following example the X and Y offsets are both positive:
* #define X_PROBE_OFFSET_FROM_EXTRUDER 10
* #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
*
* #define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
*
* +-- BACK ---+
* | |
@ -892,10 +891,10 @@
* | |
* O-- FRONT --+
* (0,0)
*
* Specify a Probe position as { X, Y, Z }
*/
#define X_PROBE_OFFSET_FROM_EXTRUDER -25 // X offset: -left +right [of the nozzle]
#define Y_PROBE_OFFSET_FROM_EXTRUDER -29 // Y offset: -front +behind [the nozzle]
#define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 // Z offset: -below +above [the nozzle]
#define NOZZLE_TO_PROBE_OFFSET { -25, -29, -12.35 }
// Certain types of probes need to stay away from edges
#define MIN_PROBE_EDGE 10
@ -929,7 +928,7 @@
*
* Use these settings to specify the distance (mm) to raise the probe (or
* lower the bed). The values set here apply over and above any (negative)
* probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
* probe Z Offset set with NOZZLE_TO_PROBE_OFFSET, M851, or the LCD.
* Only integer values >= 1 are valid here.
*
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
@ -1187,12 +1186,6 @@
#define GRID_MAX_POINTS_X 3
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
// Set the boundaries for probing (where the probe can reach).
//#define LEFT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define RIGHT_PROBE_BED_POSITION (X_BED_SIZE - (MIN_PROBE_EDGE))
//#define FRONT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define BACK_PROBE_BED_POSITION (Y_BED_SIZE - (MIN_PROBE_EDGE))
// Probe along the Y axis, advancing X after each column
//#define PROBE_Y_FIRST

19
config/examples/BQ/Hephestos_2/Configuration.h
View File

@ -889,11 +889,10 @@
/**
* Z Probe to nozzle (X,Y) offset, relative to (0, 0).
* X and Y offsets must be integers.
*
* In the following example the X and Y offsets are both positive:
* #define X_PROBE_OFFSET_FROM_EXTRUDER 10
* #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
*
* #define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
*
* +-- BACK ---+
* | |
@ -905,10 +904,10 @@
* | |
* O-- FRONT --+
* (0,0)
*
* Specify a Probe position as { X, Y, Z }
*/
#define X_PROBE_OFFSET_FROM_EXTRUDER 34 // X offset: -left +right [of the nozzle]
#define Y_PROBE_OFFSET_FROM_EXTRUDER 15 // Y offset: -front +behind [the nozzle]
#define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle]
#define NOZZLE_TO_PROBE_OFFSET { 34, 15, 0 }
// Certain types of probes need to stay away from edges
#define MIN_PROBE_EDGE 10
@ -942,7 +941,7 @@
*
* Use these settings to specify the distance (mm) to raise the probe (or
* lower the bed). The values set here apply over and above any (negative)
* probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
* probe Z Offset set with NOZZLE_TO_PROBE_OFFSET, M851, or the LCD.
* Only integer values >= 1 are valid here.
*
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
@ -1199,12 +1198,6 @@
#define GRID_MAX_POINTS_X 5
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
// Set the boundaries for probing (where the probe can reach).
//#define LEFT_PROBE_BED_POSITION X_MIN_POS + (X_PROBE_OFFSET_FROM_EXTRUDER)
//#define RIGHT_PROBE_BED_POSITION X_MAX_POS - (X_PROBE_OFFSET_FROM_EXTRUDER)
//#define FRONT_PROBE_BED_POSITION Y_MIN_POS + (Y_PROBE_OFFSET_FROM_EXTRUDER)
//#define BACK_PROBE_BED_POSITION Y_MAX_POS - (Y_PROBE_OFFSET_FROM_EXTRUDER)
// Probe along the Y axis, advancing X after each column
//#define PROBE_Y_FIRST

19
config/examples/BQ/WITBOX/Configuration.h
View File

@ -876,11 +876,10 @@
/**
* Z Probe to nozzle (X,Y) offset, relative to (0, 0).
* X and Y offsets must be integers.
*
* In the following example the X and Y offsets are both positive:
* #define X_PROBE_OFFSET_FROM_EXTRUDER 10
* #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
*
* #define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
*
* +-- BACK ---+
* | |
@ -892,10 +891,10 @@
* | |
* O-- FRONT --+
* (0,0)
*
* Specify a Probe position as { X, Y, Z }
*/
#define X_PROBE_OFFSET_FROM_EXTRUDER -25 // X offset: -left +right [of the nozzle]
#define Y_PROBE_OFFSET_FROM_EXTRUDER -29 // Y offset: -front +behind [the nozzle]
#define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 // Z offset: -below +above [the nozzle]
#define NOZZLE_TO_PROBE_OFFSET { -25, -29, -12.35 }
// Certain types of probes need to stay away from edges
#define MIN_PROBE_EDGE 10
@ -929,7 +928,7 @@
*
* Use these settings to specify the distance (mm) to raise the probe (or
* lower the bed). The values set here apply over and above any (negative)
* probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
* probe Z Offset set with NOZZLE_TO_PROBE_OFFSET, M851, or the LCD.
* Only integer values >= 1 are valid here.
*
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
@ -1187,12 +1186,6 @@
#define GRID_MAX_POINTS_X 3
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
// Set the boundaries for probing (where the probe can reach).
//#define LEFT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define RIGHT_PROBE_BED_POSITION (X_BED_SIZE - (MIN_PROBE_EDGE))
//#define FRONT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define BACK_PROBE_BED_POSITION (Y_BED_SIZE - (MIN_PROBE_EDGE))
// Probe along the Y axis, advancing X after each column
//#define PROBE_Y_FIRST

19
config/examples/Cartesio/Configuration.h
View File

@ -887,11 +887,10 @@
/**
* Z Probe to nozzle (X,Y) offset, relative to (0, 0).
* X and Y offsets must be integers.
*
* In the following example the X and Y offsets are both positive:
* #define X_PROBE_OFFSET_FROM_EXTRUDER 10
* #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
*
* #define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
*
* +-- BACK ---+
* | |
@ -903,10 +902,10 @@
* | |
* O-- FRONT --+
* (0,0)
*
* Specify a Probe position as { X, Y, Z }
*/
#define X_PROBE_OFFSET_FROM_EXTRUDER 10 // X offset: -left +right [of the nozzle]
#define Y_PROBE_OFFSET_FROM_EXTRUDER 10 // Y offset: -front +behind [the nozzle]
#define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle]
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
// Certain types of probes need to stay away from edges
#define MIN_PROBE_EDGE 10
@ -940,7 +939,7 @@
*
* Use these settings to specify the distance (mm) to raise the probe (or
* lower the bed). The values set here apply over and above any (negative)
* probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
* probe Z Offset set with NOZZLE_TO_PROBE_OFFSET, M851, or the LCD.
* Only integer values >= 1 are valid here.
*
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
@ -1198,12 +1197,6 @@
#define GRID_MAX_POINTS_X 3
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
// Set the boundaries for probing (where the probe can reach).
//#define LEFT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define RIGHT_PROBE_BED_POSITION (X_BED_SIZE - (MIN_PROBE_EDGE))
//#define FRONT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define BACK_PROBE_BED_POSITION (Y_BED_SIZE - (MIN_PROBE_EDGE))
// Probe along the Y axis, advancing X after each column
//#define PROBE_Y_FIRST

19
config/examples/Creality/CR-10/Configuration.h
View File

@ -898,11 +898,10 @@
/**
* Z Probe to nozzle (X,Y) offset, relative to (0, 0).
* X and Y offsets must be integers.
*
* In the following example the X and Y offsets are both positive:
* #define X_PROBE_OFFSET_FROM_EXTRUDER 10
* #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
*
* #define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
*
* +-- BACK ---+
* | |
@ -914,10 +913,10 @@
* | |
* O-- FRONT --+
* (0,0)
*
* Specify a Probe position as { X, Y, Z }
*/
#define X_PROBE_OFFSET_FROM_EXTRUDER 10 // X offset: -left +right [of the nozzle]
#define Y_PROBE_OFFSET_FROM_EXTRUDER 10 // Y offset: -front +behind [the nozzle]
#define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle]
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
// Certain types of probes need to stay away from edges
#define MIN_PROBE_EDGE 10
@ -951,7 +950,7 @@
*
* Use these settings to specify the distance (mm) to raise the probe (or
* lower the bed). The values set here apply over and above any (negative)
* probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
* probe Z Offset set with NOZZLE_TO_PROBE_OFFSET, M851, or the LCD.
* Only integer values >= 1 are valid here.
*
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
@ -1209,12 +1208,6 @@
#define GRID_MAX_POINTS_X 3
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
// Set the boundaries for probing (where the probe can reach).
//#define LEFT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define RIGHT_PROBE_BED_POSITION (X_BED_SIZE - (MIN_PROBE_EDGE))
//#define FRONT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define BACK_PROBE_BED_POSITION (Y_BED_SIZE - (MIN_PROBE_EDGE))
// Probe along the Y axis, advancing X after each column
//#define PROBE_Y_FIRST

19
config/examples/Creality/CR-10S/Configuration.h
View File

@ -888,11 +888,10 @@
/**
* Z Probe to nozzle (X,Y) offset, relative to (0, 0).
* X and Y offsets must be integers.
*
* In the following example the X and Y offsets are both positive:
* #define X_PROBE_OFFSET_FROM_EXTRUDER 10
* #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
*
* #define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
*
* +-- BACK ---+
* | |
@ -904,10 +903,10 @@
* | |
* O-- FRONT --+
* (0,0)
*
* Specify a Probe position as { X, Y, Z }
*/
#define X_PROBE_OFFSET_FROM_EXTRUDER 10 // X offset: -left +right [of the nozzle]
#define Y_PROBE_OFFSET_FROM_EXTRUDER 10 // Y offset: -front +behind [the nozzle]
#define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle]
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
// Certain types of probes need to stay away from edges
#define MIN_PROBE_EDGE 10
@ -941,7 +940,7 @@
*
* Use these settings to specify the distance (mm) to raise the probe (or
* lower the bed). The values set here apply over and above any (negative)
* probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
* probe Z Offset set with NOZZLE_TO_PROBE_OFFSET, M851, or the LCD.
* Only integer values >= 1 are valid here.
*
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
@ -1200,12 +1199,6 @@
#define GRID_MAX_POINTS_X 3
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
// Set the boundaries for probing (where the probe can reach).
//#define LEFT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define RIGHT_PROBE_BED_POSITION (X_BED_SIZE - (MIN_PROBE_EDGE))
//#define FRONT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define BACK_PROBE_BED_POSITION (Y_BED_SIZE - (MIN_PROBE_EDGE))
// Probe along the Y axis, advancing X after each column
//#define PROBE_Y_FIRST

19
config/examples/Creality/CR-10_5S/Configuration.h
View File

@ -889,11 +889,10 @@
/**
* Z Probe to nozzle (X,Y) offset, relative to (0, 0).
* X and Y offsets must be integers.
*
* In the following example the X and Y offsets are both positive:
* #define X_PROBE_OFFSET_FROM_EXTRUDER 10
* #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
*
* #define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
*
* +-- BACK ---+
* | |
@ -905,10 +904,10 @@
* | |
* O-- FRONT --+
* (0,0)
*
* Specify a Probe position as { X, Y, Z }
*/
#define X_PROBE_OFFSET_FROM_EXTRUDER 10 // X offset: -left +right [of the nozzle]
#define Y_PROBE_OFFSET_FROM_EXTRUDER 10 // Y offset: -front +behind [the nozzle]
#define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle]
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
// Certain types of probes need to stay away from edges
#define MIN_PROBE_EDGE 10
@ -942,7 +941,7 @@
*
* Use these settings to specify the distance (mm) to raise the probe (or
* lower the bed). The values set here apply over and above any (negative)
* probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
* probe Z Offset set with NOZZLE_TO_PROBE_OFFSET, M851, or the LCD.
* Only integer values >= 1 are valid here.
*
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
@ -1202,12 +1201,6 @@
#define GRID_MAX_POINTS_X 3
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
// Set the boundaries for probing (where the probe can reach).
//#define LEFT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define RIGHT_PROBE_BED_POSITION (X_BED_SIZE - (MIN_PROBE_EDGE))
//#define FRONT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define BACK_PROBE_BED_POSITION (Y_BED_SIZE - (MIN_PROBE_EDGE))
// Probe along the Y axis, advancing X after each column
//#define PROBE_Y_FIRST

19
config/examples/Creality/CR-10mini/Configuration.h
View File

@ -907,11 +907,10 @@
/**
* Z Probe to nozzle (X,Y) offset, relative to (0, 0).
* X and Y offsets must be integers.
*
* In the following example the X and Y offsets are both positive:
* #define X_PROBE_OFFSET_FROM_EXTRUDER 10
* #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
*
* #define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
*
* +-- BACK ---+
* | |
@ -923,10 +922,10 @@
* | |
* O-- FRONT --+
* (0,0)
*
* Specify a Probe position as { X, Y, Z }
*/
#define X_PROBE_OFFSET_FROM_EXTRUDER 10 // X offset: -left +right [of the nozzle]
#define Y_PROBE_OFFSET_FROM_EXTRUDER 10 // Y offset: -front +behind [the nozzle]
#define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle]
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
// Certain types of probes need to stay away from edges
#define MIN_PROBE_EDGE 10
@ -960,7 +959,7 @@
*
* Use these settings to specify the distance (mm) to raise the probe (or
* lower the bed). The values set here apply over and above any (negative)
* probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
* probe Z Offset set with NOZZLE_TO_PROBE_OFFSET, M851, or the LCD.
* Only integer values >= 1 are valid here.
*
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
@ -1218,12 +1217,6 @@
#define GRID_MAX_POINTS_X 3
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
// Set the boundaries for probing (where the probe can reach).
//#define LEFT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define RIGHT_PROBE_BED_POSITION (X_BED_SIZE - (MIN_PROBE_EDGE))
//#define FRONT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define BACK_PROBE_BED_POSITION (Y_BED_SIZE - (MIN_PROBE_EDGE))
// Probe along the Y axis, advancing X after each column
//#define PROBE_Y_FIRST

19
config/examples/Creality/CR-20 Pro/Configuration.h
View File

@ -891,11 +891,10 @@
/**
* Z Probe to nozzle (X,Y) offset, relative to (0, 0).
* X and Y offsets must be integers.
*
* In the following example the X and Y offsets are both positive:
* #define X_PROBE_OFFSET_FROM_EXTRUDER 10
* #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
*
* #define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
*
* +-- BACK ---+
* | |
@ -907,10 +906,10 @@
* | |
* O-- FRONT --+
* (0,0)
*
* Specify a Probe position as { X, Y, Z }
*/
#define X_PROBE_OFFSET_FROM_EXTRUDER 10 // X offset: -left +right [of the nozzle]
#define Y_PROBE_OFFSET_FROM_EXTRUDER 10 // Y offset: -front +behind [the nozzle]
#define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle]
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
// Certain types of probes need to stay away from edges
#define MIN_PROBE_EDGE 10
@ -944,7 +943,7 @@
*
* Use these settings to specify the distance (mm) to raise the probe (or
* lower the bed). The values set here apply over and above any (negative)
* probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
* probe Z Offset set with NOZZLE_TO_PROBE_OFFSET, M851, or the LCD.
* Only integer values >= 1 are valid here.
*
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
@ -1202,12 +1201,6 @@
#define GRID_MAX_POINTS_X 3
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
// Set the boundaries for probing (where the probe can reach).
//#define LEFT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define RIGHT_PROBE_BED_POSITION (X_BED_SIZE - (MIN_PROBE_EDGE))
//#define FRONT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define BACK_PROBE_BED_POSITION (Y_BED_SIZE - (MIN_PROBE_EDGE))
// Probe along the Y axis, advancing X after each column
//#define PROBE_Y_FIRST

19
config/examples/Creality/CR-20/Configuration.h
View File

@ -891,11 +891,10 @@
/**
* Z Probe to nozzle (X,Y) offset, relative to (0, 0).
* X and Y offsets must be integers.
*
* In the following example the X and Y offsets are both positive:
* #define X_PROBE_OFFSET_FROM_EXTRUDER 10
* #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
*
* #define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
*
* +-- BACK ---+
* | |
@ -907,10 +906,10 @@
* | |
* O-- FRONT --+
* (0,0)
*
* Specify a Probe position as { X, Y, Z }
*/
#define X_PROBE_OFFSET_FROM_EXTRUDER 10 // X offset: -left +right [of the nozzle]
#define Y_PROBE_OFFSET_FROM_EXTRUDER 10 // Y offset: -front +behind [the nozzle]
#define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle]
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
// Certain types of probes need to stay away from edges
#define MIN_PROBE_EDGE 10
@ -944,7 +943,7 @@
*
* Use these settings to specify the distance (mm) to raise the probe (or
* lower the bed). The values set here apply over and above any (negative)
* probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
* probe Z Offset set with NOZZLE_TO_PROBE_OFFSET, M851, or the LCD.
* Only integer values >= 1 are valid here.
*
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
@ -1202,12 +1201,6 @@
#define GRID_MAX_POINTS_X 3
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
// Set the boundaries for probing (where the probe can reach).
//#define LEFT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define RIGHT_PROBE_BED_POSITION (X_BED_SIZE - (MIN_PROBE_EDGE))
//#define FRONT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define BACK_PROBE_BED_POSITION (Y_BED_SIZE - (MIN_PROBE_EDGE))
// Probe along the Y axis, advancing X after each column
//#define PROBE_Y_FIRST

19
config/examples/Creality/CR-8/Configuration.h
View File

@ -898,11 +898,10 @@
/**
* Z Probe to nozzle (X,Y) offset, relative to (0, 0).
* X and Y offsets must be integers.
*
* In the following example the X and Y offsets are both positive:
* #define X_PROBE_OFFSET_FROM_EXTRUDER 10
* #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
*
* #define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
*
* +-- BACK ---+
* | |
@ -914,10 +913,10 @@
* | |
* O-- FRONT --+
* (0,0)
*
* Specify a Probe position as { X, Y, Z }
*/
#define X_PROBE_OFFSET_FROM_EXTRUDER 10 // X offset: -left +right [of the nozzle]
#define Y_PROBE_OFFSET_FROM_EXTRUDER 10 // Y offset: -front +behind [the nozzle]
#define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle]
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
// Certain types of probes need to stay away from edges
#define MIN_PROBE_EDGE 10
@ -951,7 +950,7 @@
*
* Use these settings to specify the distance (mm) to raise the probe (or
* lower the bed). The values set here apply over and above any (negative)
* probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
* probe Z Offset set with NOZZLE_TO_PROBE_OFFSET, M851, or the LCD.
* Only integer values >= 1 are valid here.
*
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
@ -1209,12 +1208,6 @@
#define GRID_MAX_POINTS_X 3
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
// Set the boundaries for probing (where the probe can reach).
//#define LEFT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define RIGHT_PROBE_BED_POSITION (X_BED_SIZE - (MIN_PROBE_EDGE))
//#define FRONT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define BACK_PROBE_BED_POSITION (Y_BED_SIZE - (MIN_PROBE_EDGE))
// Probe along the Y axis, advancing X after each column
//#define PROBE_Y_FIRST

19
config/examples/Creality/Ender-2/Configuration.h
View File

@ -892,11 +892,10 @@
/**
* Z Probe to nozzle (X,Y) offset, relative to (0, 0).
* X and Y offsets must be integers.
*
* In the following example the X and Y offsets are both positive:
* #define X_PROBE_OFFSET_FROM_EXTRUDER 10
* #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
*
* #define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
*
* +-- BACK ---+
* | |
@ -908,10 +907,10 @@
* | |
* O-- FRONT --+
* (0,0)
*
* Specify a Probe position as { X, Y, Z }
*/
#define X_PROBE_OFFSET_FROM_EXTRUDER 10 // X offset: -left +right [of the nozzle]
#define Y_PROBE_OFFSET_FROM_EXTRUDER 10 // Y offset: -front +behind [the nozzle]
#define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle]
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
// Certain types of probes need to stay away from edges
#define MIN_PROBE_EDGE 10
@ -945,7 +944,7 @@
*
* Use these settings to specify the distance (mm) to raise the probe (or
* lower the bed). The values set here apply over and above any (negative)
* probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
* probe Z Offset set with NOZZLE_TO_PROBE_OFFSET, M851, or the LCD.
* Only integer values >= 1 are valid here.
*
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
@ -1203,12 +1202,6 @@
#define GRID_MAX_POINTS_X 3
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
// Set the boundaries for probing (where the probe can reach).
//#define LEFT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define RIGHT_PROBE_BED_POSITION (X_BED_SIZE - (MIN_PROBE_EDGE))
//#define FRONT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define BACK_PROBE_BED_POSITION (Y_BED_SIZE - (MIN_PROBE_EDGE))
// Probe along the Y axis, advancing X after each column
//#define PROBE_Y_FIRST

19
config/examples/Creality/Ender-3/Configuration.h
View File

@ -892,11 +892,10 @@
/**
* Z Probe to nozzle (X,Y) offset, relative to (0, 0).
* X and Y offsets must be integers.
*
* In the following example the X and Y offsets are both positive:
* #define X_PROBE_OFFSET_FROM_EXTRUDER 10
* #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
*
* #define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
*
* +-- BACK ---+
* | |
@ -908,10 +907,10 @@
* | |
* O-- FRONT --+
* (0,0)
*
* Specify a Probe position as { X, Y, Z }
*/
#define X_PROBE_OFFSET_FROM_EXTRUDER 10 // X offset: -left +right [of the nozzle]
#define Y_PROBE_OFFSET_FROM_EXTRUDER 10 // Y offset: -front +behind [the nozzle]
#define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle]
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
// Certain types of probes need to stay away from edges
#define MIN_PROBE_EDGE 10
@ -945,7 +944,7 @@
*
* Use these settings to specify the distance (mm) to raise the probe (or
* lower the bed). The values set here apply over and above any (negative)
* probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
* probe Z Offset set with NOZZLE_TO_PROBE_OFFSET, M851, or the LCD.
* Only integer values >= 1 are valid here.
*
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
@ -1203,12 +1202,6 @@
#define GRID_MAX_POINTS_X 3
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
// Set the boundaries for probing (where the probe can reach).
//#define LEFT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define RIGHT_PROBE_BED_POSITION (X_BED_SIZE - (MIN_PROBE_EDGE))
//#define FRONT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define BACK_PROBE_BED_POSITION (Y_BED_SIZE - (MIN_PROBE_EDGE))
// Probe along the Y axis, advancing X after each column
//#define PROBE_Y_FIRST

19
config/examples/Creality/Ender-4/Configuration.h
View File

@ -898,11 +898,10 @@
/**
* Z Probe to nozzle (X,Y) offset, relative to (0, 0).
* X and Y offsets must be integers.
*
* In the following example the X and Y offsets are both positive:
* #define X_PROBE_OFFSET_FROM_EXTRUDER 10
* #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
*
* #define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
*
* +-- BACK ---+
* | |
@ -914,10 +913,10 @@
* | |
* O-- FRONT --+
* (0,0)
*
* Specify a Probe position as { X, Y, Z }
*/
#define X_PROBE_OFFSET_FROM_EXTRUDER 10 // X offset: -left +right [of the nozzle]
#define Y_PROBE_OFFSET_FROM_EXTRUDER 10 // Y offset: -front +behind [the nozzle]
#define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle]
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
// Certain types of probes need to stay away from edges
#define MIN_PROBE_EDGE 10
@ -951,7 +950,7 @@
*
* Use these settings to specify the distance (mm) to raise the probe (or
* lower the bed). The values set here apply over and above any (negative)
* probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
* probe Z Offset set with NOZZLE_TO_PROBE_OFFSET, M851, or the LCD.
* Only integer values >= 1 are valid here.
*
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
@ -1209,12 +1208,6 @@
#define GRID_MAX_POINTS_X 3
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
// Set the boundaries for probing (where the probe can reach).
//#define LEFT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define RIGHT_PROBE_BED_POSITION (X_BED_SIZE - (MIN_PROBE_EDGE))
//#define FRONT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define BACK_PROBE_BED_POSITION (Y_BED_SIZE - (MIN_PROBE_EDGE))
// Probe along the Y axis, advancing X after each column
//#define PROBE_Y_FIRST

19
config/examples/Creality/Ender-5/Configuration.h
View File

@ -891,11 +891,10 @@
/**
* Z Probe to nozzle (X,Y) offset, relative to (0, 0).
* X and Y offsets must be integers.
*
* In the following example the X and Y offsets are both positive:
* #define X_PROBE_OFFSET_FROM_EXTRUDER 10
* #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
*
* #define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
*
* +-- BACK ---+
* | |
@ -907,10 +906,10 @@
* | |
* O-- FRONT --+
* (0,0)
*
* Specify a Probe position as { X, Y, Z }
*/
#define X_PROBE_OFFSET_FROM_EXTRUDER 10 // X offset: -left +right [of the nozzle]
#define Y_PROBE_OFFSET_FROM_EXTRUDER 10 // Y offset: -front +behind [the nozzle]
#define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle]
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
// Certain types of probes need to stay away from edges
#define MIN_PROBE_EDGE 10
@ -944,7 +943,7 @@
*
* Use these settings to specify the distance (mm) to raise the probe (or
* lower the bed). The values set here apply over and above any (negative)
* probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
* probe Z Offset set with NOZZLE_TO_PROBE_OFFSET, M851, or the LCD.
* Only integer values >= 1 are valid here.
*
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
@ -1202,12 +1201,6 @@
#define GRID_MAX_POINTS_X 3
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
// Set the boundaries for probing (where the probe can reach).
//#define LEFT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define RIGHT_PROBE_BED_POSITION (X_BED_SIZE - (MIN_PROBE_EDGE))
//#define FRONT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define BACK_PROBE_BED_POSITION (Y_BED_SIZE - (MIN_PROBE_EDGE))
// Probe along the Y axis, advancing X after each column
//#define PROBE_Y_FIRST

19
config/examples/Dagoma/Disco Ultimate/Configuration.h
View File

@ -888,11 +888,10 @@
/**
* Z Probe to nozzle (X,Y) offset, relative to (0, 0).
* X and Y offsets must be integers.
*
* In the following example the X and Y offsets are both positive:
* #define X_PROBE_OFFSET_FROM_EXTRUDER 10
* #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
*
* #define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
*
* +-- BACK ---+
* | |
@ -904,10 +903,10 @@
* | |
* O-- FRONT --+
* (0,0)
*
* Specify a Probe position as { X, Y, Z }
*/
#define X_PROBE_OFFSET_FROM_EXTRUDER 0 // X offset: -left +right [of the nozzle]
#define Y_PROBE_OFFSET_FROM_EXTRUDER 21 // Y offset: -front +behind [the nozzle]
#define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle]
#define NOZZLE_TO_PROBE_OFFSET { 0, 21, 0 }
// Certain types of probes need to stay away from edges
#define MIN_PROBE_EDGE 10
@ -941,7 +940,7 @@
*
* Use these settings to specify the distance (mm) to raise the probe (or
* lower the bed). The values set here apply over and above any (negative)
* probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
* probe Z Offset set with NOZZLE_TO_PROBE_OFFSET, M851, or the LCD.
* Only integer values >= 1 are valid here.
*
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
@ -1199,12 +1198,6 @@
#define GRID_MAX_POINTS_X 3
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
// Set the boundaries for probing (where the probe can reach).
//#define LEFT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define RIGHT_PROBE_BED_POSITION (X_BED_SIZE - (MIN_PROBE_EDGE))
//#define FRONT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define BACK_PROBE_BED_POSITION (Y_BED_SIZE - (MIN_PROBE_EDGE))
// Probe along the Y axis, advancing X after each column
//#define PROBE_Y_FIRST

19
config/examples/EVNOVO (Artillery)/Sidewinder X1/Configuration.h
View File

@ -893,11 +893,10 @@
/**
* Z Probe to nozzle (X,Y) offset, relative to (0, 0).
* X and Y offsets must be integers.
*
* In the following example the X and Y offsets are both positive:
* #define X_PROBE_OFFSET_FROM_EXTRUDER 10
* #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
*
* #define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
*
* +-- BACK ---+
* | |
@ -909,10 +908,10 @@
* | |
* O-- FRONT --+
* (0,0)
*
* Specify a Probe position as { X, Y, Z }
*/
#define X_PROBE_OFFSET_FROM_EXTRUDER 10 // X offset: -left +right [of the nozzle]
#define Y_PROBE_OFFSET_FROM_EXTRUDER 10 // Y offset: -front +behind [the nozzle]
#define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle]
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
// Certain types of probes need to stay away from edges
#define MIN_PROBE_EDGE 10
@ -946,7 +945,7 @@
*
* Use these settings to specify the distance (mm) to raise the probe (or
* lower the bed). The values set here apply over and above any (negative)
* probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
* probe Z Offset set with NOZZLE_TO_PROBE_OFFSET, M851, or the LCD.
* Only integer values >= 1 are valid here.
*
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
@ -1204,12 +1203,6 @@
#define GRID_MAX_POINTS_X 3
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
// Set the boundaries for probing (where the probe can reach).
//#define LEFT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define RIGHT_PROBE_BED_POSITION (X_BED_SIZE - (MIN_PROBE_EDGE))
//#define FRONT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define BACK_PROBE_BED_POSITION (Y_BED_SIZE - (MIN_PROBE_EDGE))
// Probe along the Y axis, advancing X after each column
//#define PROBE_Y_FIRST

19
config/examples/Einstart-S/Configuration.h
View File

@ -898,11 +898,10 @@
/**
* Z Probe to nozzle (X,Y) offset, relative to (0, 0).
* X and Y offsets must be integers.
*
* In the following example the X and Y offsets are both positive:
* #define X_PROBE_OFFSET_FROM_EXTRUDER 10
* #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
*
* #define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
*
* +-- BACK ---+
* | |
@ -914,10 +913,10 @@
* | |
* O-- FRONT --+
* (0,0)
*
* Specify a Probe position as { X, Y, Z }
*/
#define X_PROBE_OFFSET_FROM_EXTRUDER 10 // X offset: -left +right [of the nozzle]
#define Y_PROBE_OFFSET_FROM_EXTRUDER 10 // Y offset: -front +behind [the nozzle]
#define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle]
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
// Certain types of probes need to stay away from edges
#define MIN_PROBE_EDGE 10
@ -951,7 +950,7 @@
*
* Use these settings to specify the distance (mm) to raise the probe (or
* lower the bed). The values set here apply over and above any (negative)
* probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
* probe Z Offset set with NOZZLE_TO_PROBE_OFFSET, M851, or the LCD.
* Only integer values >= 1 are valid here.
*
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
@ -1209,12 +1208,6 @@
#define GRID_MAX_POINTS_X 3
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
// Set the boundaries for probing (where the probe can reach).
//#define LEFT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define RIGHT_PROBE_BED_POSITION (X_BED_SIZE - (MIN_PROBE_EDGE))
//#define FRONT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define BACK_PROBE_BED_POSITION (Y_BED_SIZE - (MIN_PROBE_EDGE))
// Probe along the Y axis, advancing X after each column
//#define PROBE_Y_FIRST

19
config/examples/FYSETC/AIO_II/Configuration.h
View File

@ -893,11 +893,10 @@
/**
* Z Probe to nozzle (X,Y) offset, relative to (0, 0).
* X and Y offsets must be integers.
*
* In the following example the X and Y offsets are both positive:
* #define X_PROBE_OFFSET_FROM_EXTRUDER 10
* #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
*
* #define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
*
* +-- BACK ---+
* | |
@ -909,10 +908,10 @@
* | |
* O-- FRONT --+
* (0,0)
*
* Specify a Probe position as { X, Y, Z }
*/
#define X_PROBE_OFFSET_FROM_EXTRUDER 10 // X offset: -left +right [of the nozzle]
#define Y_PROBE_OFFSET_FROM_EXTRUDER 10 // Y offset: -front +behind [the nozzle]
#define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle]
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
// Certain types of probes need to stay away from edges
#define MIN_PROBE_EDGE 10
@ -946,7 +945,7 @@
*
* Use these settings to specify the distance (mm) to raise the probe (or
* lower the bed). The values set here apply over and above any (negative)
* probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
* probe Z Offset set with NOZZLE_TO_PROBE_OFFSET, M851, or the LCD.
* Only integer values >= 1 are valid here.
*
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
@ -1204,12 +1203,6 @@
#define GRID_MAX_POINTS_X 3
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
// Set the boundaries for probing (where the probe can reach).
//#define LEFT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define RIGHT_PROBE_BED_POSITION (X_BED_SIZE - (MIN_PROBE_EDGE))
//#define FRONT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define BACK_PROBE_BED_POSITION (Y_BED_SIZE - (MIN_PROBE_EDGE))
// Probe along the Y axis, advancing X after each column
//#define PROBE_Y_FIRST

19
config/examples/FYSETC/Cheetah 1.2/BLTouch/Configuration.h
View File

@ -893,11 +893,10 @@
/**
* Z Probe to nozzle (X,Y) offset, relative to (0, 0).
* X and Y offsets must be integers.
*
* In the following example the X and Y offsets are both positive:
* #define X_PROBE_OFFSET_FROM_EXTRUDER 10
* #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
*
* #define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
*
* +-- BACK ---+
* | |
@ -909,10 +908,10 @@
* | |
* O-- FRONT --+
* (0,0)
*
* Specify a Probe position as { X, Y, Z }
*/
#define X_PROBE_OFFSET_FROM_EXTRUDER -44 // X offset: -left +right [of the nozzle]
#define Y_PROBE_OFFSET_FROM_EXTRUDER -6 // Y offset: -front +behind [the nozzle]
#define Z_PROBE_OFFSET_FROM_EXTRUDER -3.9 // Z offset: -below +above [the nozzle]
#define NOZZLE_TO_PROBE_OFFSET { -44, -6, -3.9 }
// Certain types of probes need to stay away from edges
#define MIN_PROBE_EDGE 10
@ -946,7 +945,7 @@
*
* Use these settings to specify the distance (mm) to raise the probe (or
* lower the bed). The values set here apply over and above any (negative)
* probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
* probe Z Offset set with NOZZLE_TO_PROBE_OFFSET, M851, or the LCD.
* Only integer values >= 1 are valid here.
*
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
@ -1204,12 +1203,6 @@
#define GRID_MAX_POINTS_X 3
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
// Set the boundaries for probing (where the probe can reach).
//#define LEFT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define RIGHT_PROBE_BED_POSITION (X_BED_SIZE - (MIN_PROBE_EDGE))
//#define FRONT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define BACK_PROBE_BED_POSITION (Y_BED_SIZE - (MIN_PROBE_EDGE))
// Probe along the Y axis, advancing X after each column
//#define PROBE_Y_FIRST

19
config/examples/FYSETC/Cheetah 1.2/base/Configuration.h
View File

@ -893,11 +893,10 @@
/**
* Z Probe to nozzle (X,Y) offset, relative to (0, 0).
* X and Y offsets must be integers.
*
* In the following example the X and Y offsets are both positive:
* #define X_PROBE_OFFSET_FROM_EXTRUDER 10
* #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
*
* #define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
*
* +-- BACK ---+
* | |
@ -909,10 +908,10 @@
* | |
* O-- FRONT --+
* (0,0)
*
* Specify a Probe position as { X, Y, Z }
*/
#define X_PROBE_OFFSET_FROM_EXTRUDER 10 // X offset: -left +right [of the nozzle]
#define Y_PROBE_OFFSET_FROM_EXTRUDER 10 // Y offset: -front +behind [the nozzle]
#define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle]
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
// Certain types of probes need to stay away from edges
#define MIN_PROBE_EDGE 10
@ -946,7 +945,7 @@
*
* Use these settings to specify the distance (mm) to raise the probe (or
* lower the bed). The values set here apply over and above any (negative)
* probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
* probe Z Offset set with NOZZLE_TO_PROBE_OFFSET, M851, or the LCD.
* Only integer values >= 1 are valid here.
*
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
@ -1204,12 +1203,6 @@
#define GRID_MAX_POINTS_X 3
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
// Set the boundaries for probing (where the probe can reach).
//#define LEFT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define RIGHT_PROBE_BED_POSITION (X_BED_SIZE - (MIN_PROBE_EDGE))
//#define FRONT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define BACK_PROBE_BED_POSITION (Y_BED_SIZE - (MIN_PROBE_EDGE))
// Probe along the Y axis, advancing X after each column
//#define PROBE_Y_FIRST

19
config/examples/FYSETC/Cheetah/BLTouch/Configuration.h
View File

@ -893,11 +893,10 @@
/**
* Z Probe to nozzle (X,Y) offset, relative to (0, 0).
* X and Y offsets must be integers.
*
* In the following example the X and Y offsets are both positive:
* #define X_PROBE_OFFSET_FROM_EXTRUDER 10
* #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
*
* #define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
*
* +-- BACK ---+
* | |
@ -909,10 +908,10 @@
* | |
* O-- FRONT --+
* (0,0)
*
* Specify a Probe position as { X, Y, Z }
*/
#define X_PROBE_OFFSET_FROM_EXTRUDER -44 // X offset: -left +right [of the nozzle]
#define Y_PROBE_OFFSET_FROM_EXTRUDER -6 // Y offset: -front +behind [the nozzle]
#define Z_PROBE_OFFSET_FROM_EXTRUDER -3.9 // Z offset: -below +above [the nozzle]
#define NOZZLE_TO_PROBE_OFFSET { -44, -6, -3.9 }
// Certain types of probes need to stay away from edges
#define MIN_PROBE_EDGE 10
@ -946,7 +945,7 @@
*
* Use these settings to specify the distance (mm) to raise the probe (or
* lower the bed). The values set here apply over and above any (negative)
* probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
* probe Z Offset set with NOZZLE_TO_PROBE_OFFSET, M851, or the LCD.
* Only integer values >= 1 are valid here.
*
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
@ -1204,12 +1203,6 @@
#define GRID_MAX_POINTS_X 3
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
// Set the boundaries for probing (where the probe can reach).
//#define LEFT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define RIGHT_PROBE_BED_POSITION (X_BED_SIZE - (MIN_PROBE_EDGE))
//#define FRONT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define BACK_PROBE_BED_POSITION (Y_BED_SIZE - (MIN_PROBE_EDGE))
// Probe along the Y axis, advancing X after each column
//#define PROBE_Y_FIRST

19
config/examples/FYSETC/Cheetah/base/Configuration.h
View File

@ -893,11 +893,10 @@
/**
* Z Probe to nozzle (X,Y) offset, relative to (0, 0).
* X and Y offsets must be integers.
*
* In the following example the X and Y offsets are both positive:
* #define X_PROBE_OFFSET_FROM_EXTRUDER 10
* #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
*
* #define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
*
* +-- BACK ---+
* | |
@ -909,10 +908,10 @@
* | |
* O-- FRONT --+
* (0,0)
*
* Specify a Probe position as { X, Y, Z }
*/
#define X_PROBE_OFFSET_FROM_EXTRUDER 10 // X offset: -left +right [of the nozzle]
#define Y_PROBE_OFFSET_FROM_EXTRUDER 10 // Y offset: -front +behind [the nozzle]
#define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle]
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
// Certain types of probes need to stay away from edges
#define MIN_PROBE_EDGE 10
@ -946,7 +945,7 @@
*
* Use these settings to specify the distance (mm) to raise the probe (or
* lower the bed). The values set here apply over and above any (negative)
* probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
* probe Z Offset set with NOZZLE_TO_PROBE_OFFSET, M851, or the LCD.
* Only integer values >= 1 are valid here.
*
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
@ -1204,12 +1203,6 @@
#define GRID_MAX_POINTS_X 3
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
// Set the boundaries for probing (where the probe can reach).
//#define LEFT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define RIGHT_PROBE_BED_POSITION (X_BED_SIZE - (MIN_PROBE_EDGE))
//#define FRONT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define BACK_PROBE_BED_POSITION (Y_BED_SIZE - (MIN_PROBE_EDGE))
// Probe along the Y axis, advancing X after each column
//#define PROBE_Y_FIRST

19
config/examples/FYSETC/F6_13/Configuration.h
View File

@ -890,11 +890,10 @@
/**
* Z Probe to nozzle (X,Y) offset, relative to (0, 0).
* X and Y offsets must be integers.
*
* In the following example the X and Y offsets are both positive:
* #define X_PROBE_OFFSET_FROM_EXTRUDER 10
* #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
*
* #define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
*
* +-- BACK ---+
* | |
@ -906,10 +905,10 @@
* | |
* O-- FRONT --+
* (0,0)
*
* Specify a Probe position as { X, Y, Z }
*/
#define X_PROBE_OFFSET_FROM_EXTRUDER 10 // X offset: -left +right [of the nozzle]
#define Y_PROBE_OFFSET_FROM_EXTRUDER 10 // Y offset: -front +behind [the nozzle]
#define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle]
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
// Certain types of probes need to stay away from edges
#define MIN_PROBE_EDGE 10
@ -943,7 +942,7 @@
*
* Use these settings to specify the distance (mm) to raise the probe (or
* lower the bed). The values set here apply over and above any (negative)
* probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
* probe Z Offset set with NOZZLE_TO_PROBE_OFFSET, M851, or the LCD.
* Only integer values >= 1 are valid here.
*
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
@ -1201,12 +1200,6 @@
#define GRID_MAX_POINTS_X 3
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
// Set the boundaries for probing (where the probe can reach).
//#define LEFT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define RIGHT_PROBE_BED_POSITION (X_BED_SIZE - (MIN_PROBE_EDGE))
//#define FRONT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define BACK_PROBE_BED_POSITION (Y_BED_SIZE - (MIN_PROBE_EDGE))
// Probe along the Y axis, advancing X after each column
//#define PROBE_Y_FIRST

19
config/examples/Felix/Configuration.h
View File

@ -870,11 +870,10 @@
/**
* Z Probe to nozzle (X,Y) offset, relative to (0, 0).
* X and Y offsets must be integers.
*
* In the following example the X and Y offsets are both positive:
* #define X_PROBE_OFFSET_FROM_EXTRUDER 10
* #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
*
* #define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
*
* +-- BACK ---+
* | |
@ -886,10 +885,10 @@
* | |
* O-- FRONT --+
* (0,0)
*
* Specify a Probe position as { X, Y, Z }
*/
#define X_PROBE_OFFSET_FROM_EXTRUDER -25 // X offset: -left +right [of the nozzle]
#define Y_PROBE_OFFSET_FROM_EXTRUDER -29 // Y offset: -front +behind [the nozzle]
#define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 // Z offset: -below +above [the nozzle]
#define NOZZLE_TO_PROBE_OFFSET { -25, -29, -12.35 }
// Certain types of probes need to stay away from edges
#define MIN_PROBE_EDGE 10
@ -923,7 +922,7 @@
*
* Use these settings to specify the distance (mm) to raise the probe (or
* lower the bed). The values set here apply over and above any (negative)
* probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
* probe Z Offset set with NOZZLE_TO_PROBE_OFFSET, M851, or the LCD.
* Only integer values >= 1 are valid here.
*
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
@ -1181,12 +1180,6 @@
#define GRID_MAX_POINTS_X 3
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
// Set the boundaries for probing (where the probe can reach).
//#define LEFT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define RIGHT_PROBE_BED_POSITION (X_BED_SIZE - (MIN_PROBE_EDGE))
//#define FRONT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define BACK_PROBE_BED_POSITION (Y_BED_SIZE - (MIN_PROBE_EDGE))
// Probe along the Y axis, advancing X after each column
//#define PROBE_Y_FIRST

19
config/examples/Felix/DUAL/Configuration.h
View File

@ -870,11 +870,10 @@
/**
* Z Probe to nozzle (X,Y) offset, relative to (0, 0).
* X and Y offsets must be integers.
*
* In the following example the X and Y offsets are both positive:
* #define X_PROBE_OFFSET_FROM_EXTRUDER 10
* #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
*
* #define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
*
* +-- BACK ---+
* | |
@ -886,10 +885,10 @@
* | |
* O-- FRONT --+
* (0,0)
*
* Specify a Probe position as { X, Y, Z }
*/
#define X_PROBE_OFFSET_FROM_EXTRUDER -25 // X offset: -left +right [of the nozzle]
#define Y_PROBE_OFFSET_FROM_EXTRUDER -29 // Y offset: -front +behind [the nozzle]
#define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 // Z offset: -below +above [the nozzle]
#define NOZZLE_TO_PROBE_OFFSET { -25, -29, -12.35 }
// Certain types of probes need to stay away from edges
#define MIN_PROBE_EDGE 10
@ -923,7 +922,7 @@
*
* Use these settings to specify the distance (mm) to raise the probe (or
* lower the bed). The values set here apply over and above any (negative)
* probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
* probe Z Offset set with NOZZLE_TO_PROBE_OFFSET, M851, or the LCD.
* Only integer values >= 1 are valid here.
*
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
@ -1181,12 +1180,6 @@
#define GRID_MAX_POINTS_X 3
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
// Set the boundaries for probing (where the probe can reach).
//#define LEFT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define RIGHT_PROBE_BED_POSITION (X_BED_SIZE - (MIN_PROBE_EDGE))
//#define FRONT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define BACK_PROBE_BED_POSITION (Y_BED_SIZE - (MIN_PROBE_EDGE))
// Probe along the Y axis, advancing X after each column
//#define PROBE_Y_FIRST

19
config/examples/FlashForge/CreatorPro/Configuration.h
View File

@ -880,11 +880,10 @@
/**
* Z Probe to nozzle (X,Y) offset, relative to (0, 0).
* X and Y offsets must be integers.
*
* In the following example the X and Y offsets are both positive:
* #define X_PROBE_OFFSET_FROM_EXTRUDER 10
* #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
*
* #define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
*
* +-- BACK ---+
* | |
@ -896,10 +895,10 @@
* | |
* O-- FRONT --+
* (0,0)
*
* Specify a Probe position as { X, Y, Z }
*/
#define X_PROBE_OFFSET_FROM_EXTRUDER 10 // X offset: -left +right [of the nozzle]
#define Y_PROBE_OFFSET_FROM_EXTRUDER 10 // Y offset: -front +behind [the nozzle]
#define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle]
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
// Certain types of probes need to stay away from edges
#define MIN_PROBE_EDGE 10
@ -933,7 +932,7 @@
*
* Use these settings to specify the distance (mm) to raise the probe (or
* lower the bed). The values set here apply over and above any (negative)
* probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
* probe Z Offset set with NOZZLE_TO_PROBE_OFFSET, M851, or the LCD.
* Only integer values >= 1 are valid here.
*
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
@ -1192,12 +1191,6 @@
#define GRID_MAX_POINTS_X 3
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
// Set the boundaries for probing (where the probe can reach).
//#define LEFT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define RIGHT_PROBE_BED_POSITION (X_BED_SIZE - (MIN_PROBE_EDGE))
//#define FRONT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define BACK_PROBE_BED_POSITION (Y_BED_SIZE - (MIN_PROBE_EDGE))
// Probe along the Y axis, advancing X after each column
//#define PROBE_Y_FIRST

19
config/examples/FolgerTech/i3-2020/Configuration.h
View File

@ -894,11 +894,10 @@
/**
* Z Probe to nozzle (X,Y) offset, relative to (0, 0).
* X and Y offsets must be integers.
*
* In the following example the X and Y offsets are both positive:
* #define X_PROBE_OFFSET_FROM_EXTRUDER 10
* #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
*
* #define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
*
* +-- BACK ---+
* | |
@ -910,10 +909,10 @@
* | |
* O-- FRONT --+
* (0,0)
*
* Specify a Probe position as { X, Y, Z }
*/
#define X_PROBE_OFFSET_FROM_EXTRUDER 38 // X offset: -left +right [of the nozzle]
#define Y_PROBE_OFFSET_FROM_EXTRUDER -7 // Y offset: -front +behind [the nozzle]
#define Z_PROBE_OFFSET_FROM_EXTRUDER -10.75 // Z offset: -below +above [the nozzle]
#define NOZZLE_TO_PROBE_OFFSET { 38, -7, -10.75 }
// Certain types of probes need to stay away from edges
#define MIN_PROBE_EDGE 0
@ -947,7 +946,7 @@
*
* Use these settings to specify the distance (mm) to raise the probe (or
* lower the bed). The values set here apply over and above any (negative)
* probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
* probe Z Offset set with NOZZLE_TO_PROBE_OFFSET, M851, or the LCD.
* Only integer values >= 1 are valid here.
*
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
@ -1205,12 +1204,6 @@
#define GRID_MAX_POINTS_X 3
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
// Set the boundaries for probing (where the probe can reach).
//#define LEFT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define RIGHT_PROBE_BED_POSITION (X_BED_SIZE - (MIN_PROBE_EDGE))
//#define FRONT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define BACK_PROBE_BED_POSITION (Y_BED_SIZE - (MIN_PROBE_EDGE))
// Probe along the Y axis, advancing X after each column
//#define PROBE_Y_FIRST

19
config/examples/Formbot/Raptor/Configuration.h
View File

@ -971,11 +971,10 @@
/**
* Z Probe to nozzle (X,Y) offset, relative to (0, 0).
* X and Y offsets must be integers.
*
* In the following example the X and Y offsets are both positive:
* #define X_PROBE_OFFSET_FROM_EXTRUDER 10
* #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
*
* #define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
*
* +-- BACK ---+
* | |
@ -987,10 +986,10 @@
* | |
* O-- FRONT --+
* (0,0)
*
* Specify a Probe position as { X, Y, Z }
*/
#define X_PROBE_OFFSET_FROM_EXTRUDER -22 // X offset: -left +right [of the nozzle]
#define Y_PROBE_OFFSET_FROM_EXTRUDER 0 // Y offset: -front +behind [the nozzle]
#define Z_PROBE_OFFSET_FROM_EXTRUDER -1.5 // Z offset: -below +above [the nozzle]
#define NOZZLE_TO_PROBE_OFFSET { -22, 0, -1.5 }
#define MIN_PROBE_EDGE 10
// X and Y axis travel speed (mm/m) between probes
@ -1022,7 +1021,7 @@
*
* Use these settings to specify the distance (mm) to raise the probe (or
* lower the bed). The values set here apply over and above any (negative)
* probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
* probe Z Offset set with NOZZLE_TO_PROBE_OFFSET, M851, or the LCD.
* Only integer values >= 1 are valid here.
*
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
@ -1301,12 +1300,6 @@
#define GRID_MAX_POINTS_X 6
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
// Set the boundaries for probing (where the probe can reach).
#define LEFT_PROBE_BED_POSITION 30
#define RIGHT_PROBE_BED_POSITION 365
#define FRONT_PROBE_BED_POSITION 30
#define BACK_PROBE_BED_POSITION 365
// The Z probe minimum outer margin (to validate G29 parameters).
#define MIN_PROBE_EDGE 10

19
config/examples/Formbot/T_Rex_2+/Configuration.h
View File

@ -917,11 +917,10 @@
/**
* Z Probe to nozzle (X,Y) offset, relative to (0, 0).
* X and Y offsets must be integers.
*
* In the following example the X and Y offsets are both positive:
* #define X_PROBE_OFFSET_FROM_EXTRUDER 10
* #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
*
* #define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
*
* +-- BACK ---+
* | |
@ -933,10 +932,10 @@
* | |
* O-- FRONT --+
* (0,0)
*
* Specify a Probe position as { X, Y, Z }
*/
#define X_PROBE_OFFSET_FROM_EXTRUDER -3 // X offset: -left +right [of the nozzle]
#define Y_PROBE_OFFSET_FROM_EXTRUDER 31 // Y offset: -front +behind [the nozzle]
#define Z_PROBE_OFFSET_FROM_EXTRUDER -1.25 // Z offset: -below +above [the nozzle]
#define NOZZLE_TO_PROBE_OFFSET { -3, 31, -1.25 }
// Certain types of probes need to stay away from edges
#define MIN_PROBE_EDGE 0
@ -970,7 +969,7 @@
*
* Use these settings to specify the distance (mm) to raise the probe (or
* lower the bed). The values set here apply over and above any (negative)
* probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
* probe Z Offset set with NOZZLE_TO_PROBE_OFFSET, M851, or the LCD.
* Only integer values >= 1 are valid here.
*
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
@ -1228,12 +1227,6 @@
#define GRID_MAX_POINTS_X 3
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
// Set the boundaries for probing (where the probe can reach).
//#define LEFT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define RIGHT_PROBE_BED_POSITION (X_BED_SIZE - (MIN_PROBE_EDGE))
//#define FRONT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define BACK_PROBE_BED_POSITION (Y_BED_SIZE - (MIN_PROBE_EDGE))
// Probe along the Y axis, advancing X after each column
//#define PROBE_Y_FIRST

19
config/examples/Formbot/T_Rex_3/Configuration.h
View File

@ -904,11 +904,10 @@
/**
* Z Probe to nozzle (X,Y) offset, relative to (0, 0).
* X and Y offsets must be integers.
*
* In the following example the X and Y offsets are both positive:
* #define X_PROBE_OFFSET_FROM_EXTRUDER 10
* #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
*
* #define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
*
* +-- BACK ---+
* | |
@ -920,10 +919,10 @@
* | |
* O-- FRONT --+
* (0,0)
*
* Specify a Probe position as { X, Y, Z }
*/
#define X_PROBE_OFFSET_FROM_EXTRUDER -3 // X offset: -left +right [of the nozzle]
#define Y_PROBE_OFFSET_FROM_EXTRUDER 31 // Y offset: -front +behind [the nozzle]
#define Z_PROBE_OFFSET_FROM_EXTRUDER -1.25 // Z offset: -below +above [the nozzle]
#define NOZZLE_TO_PROBE_OFFSET { -3, 31, -1.25 }
// Certain types of probes need to stay away from edges
#define MIN_PROBE_EDGE 0
@ -957,7 +956,7 @@
*
* Use these settings to specify the distance (mm) to raise the probe (or
* lower the bed). The values set here apply over and above any (negative)
* probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
* probe Z Offset set with NOZZLE_TO_PROBE_OFFSET, M851, or the LCD.
* Only integer values >= 1 are valid here.
*
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
@ -1224,12 +1223,6 @@
#define GRID_MAX_POINTS_X 3
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
// Set the boundaries for probing (where the probe can reach).
//#define LEFT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define RIGHT_PROBE_BED_POSITION (X_BED_SIZE - MIN_PROBE_EDGE)
//#define FRONT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define BACK_PROBE_BED_POSITION (Y_BED_SIZE - MIN_PROBE_EDGE)
// Probe along the Y axis, advancing X after each column
//#define PROBE_Y_FIRST

19
config/examples/Geeetech/A10/Configuration.h
View File

@ -871,11 +871,10 @@
/**
* Z Probe to nozzle (X,Y) offset, relative to (0, 0).
* X and Y offsets must be integers.
*
* In the following example the X and Y offsets are both positive:
* #define X_PROBE_OFFSET_FROM_EXTRUDER 10
* #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
*
* #define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
*
* +-- BACK ---+
* | |
@ -887,10 +886,10 @@
* | |
* O-- FRONT --+
* (0,0)
*
* Specify a Probe position as { X, Y, Z }
*/
#define X_PROBE_OFFSET_FROM_EXTRUDER -37 // X offset: -left +right [of the nozzle]
#define Y_PROBE_OFFSET_FROM_EXTRUDER 0 // Y offset: -front +behind [the nozzle]
#define Z_PROBE_OFFSET_FROM_EXTRUDER -3.6 // Z offset: -below +above [the nozzle]
#define NOZZLE_TO_PROBE_OFFSET { -37, 0, -3.6 }
// Certain types of probes need to stay away from edges
#define MIN_PROBE_EDGE 10
@ -924,7 +923,7 @@
*
* Use these settings to specify the distance (mm) to raise the probe (or
* lower the bed). The values set here apply over and above any (negative)
* probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
* probe Z Offset set with NOZZLE_TO_PROBE_OFFSET, M851, or the LCD.
* Only integer values >= 1 are valid here.
*
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
@ -1184,12 +1183,6 @@
#define GRID_MAX_POINTS_X 5
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
// Set the boundaries for probing (where the probe can reach).
//#define LEFT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define RIGHT_PROBE_BED_POSITION (X_BED_SIZE - (MIN_PROBE_EDGE))
//#define FRONT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define BACK_PROBE_BED_POSITION (Y_BED_SIZE - (MIN_PROBE_EDGE))
// Probe along the Y axis, advancing X after each column
//#define PROBE_Y_FIRST

19
config/examples/Geeetech/A10M/Configuration.h
View File

@ -871,11 +871,10 @@
/**
* Z Probe to nozzle (X,Y) offset, relative to (0, 0).
* X and Y offsets must be integers.
*
* In the following example the X and Y offsets are both positive:
* #define X_PROBE_OFFSET_FROM_EXTRUDER 10
* #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
*
* #define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
*
* +-- BACK ---+
* | |
@ -887,10 +886,10 @@
* | |
* O-- FRONT --+
* (0,0)
*
* Specify a Probe position as { X, Y, Z }
*/
#define X_PROBE_OFFSET_FROM_EXTRUDER -37 // X offset: -left +right [of the nozzle]
#define Y_PROBE_OFFSET_FROM_EXTRUDER 0 // Y offset: -front +behind [the nozzle]
#define Z_PROBE_OFFSET_FROM_EXTRUDER -3.6 // Z offset: -below +above [the nozzle]
#define NOZZLE_TO_PROBE_OFFSET { -37, 0, -3.6 }
// Certain types of probes need to stay away from edges
#define MIN_PROBE_EDGE 10
@ -924,7 +923,7 @@
*
* Use these settings to specify the distance (mm) to raise the probe (or
* lower the bed). The values set here apply over and above any (negative)
* probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
* probe Z Offset set with NOZZLE_TO_PROBE_OFFSET, M851, or the LCD.
* Only integer values >= 1 are valid here.
*
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
@ -1184,12 +1183,6 @@
#define GRID_MAX_POINTS_X 5
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
// Set the boundaries for probing (where the probe can reach).
//#define LEFT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define RIGHT_PROBE_BED_POSITION (X_BED_SIZE - (MIN_PROBE_EDGE))
//#define FRONT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define BACK_PROBE_BED_POSITION (Y_BED_SIZE - (MIN_PROBE_EDGE))
// Probe along the Y axis, advancing X after each column
//#define PROBE_Y_FIRST

19
config/examples/Geeetech/A20M/Configuration.h
View File

@ -871,11 +871,10 @@
/**
* Z Probe to nozzle (X,Y) offset, relative to (0, 0).
* X and Y offsets must be integers.
*
* In the following example the X and Y offsets are both positive:
* #define X_PROBE_OFFSET_FROM_EXTRUDER 10
* #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
*
* #define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
*
* +-- BACK ---+
* | |
@ -887,10 +886,10 @@
* | |
* O-- FRONT --+
* (0,0)
*
* Specify a Probe position as { X, Y, Z }
*/
#define X_PROBE_OFFSET_FROM_EXTRUDER -37 // X offset: -left +right [of the nozzle]
#define Y_PROBE_OFFSET_FROM_EXTRUDER 0 // Y offset: -front +behind [the nozzle]
#define Z_PROBE_OFFSET_FROM_EXTRUDER -3.6 // Z offset: -below +above [the nozzle]
#define NOZZLE_TO_PROBE_OFFSET { -37, 0, -3.6 }
// Certain types of probes need to stay away from edges
#define MIN_PROBE_EDGE 10
@ -924,7 +923,7 @@
*
* Use these settings to specify the distance (mm) to raise the probe (or
* lower the bed). The values set here apply over and above any (negative)
* probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
* probe Z Offset set with NOZZLE_TO_PROBE_OFFSET, M851, or the LCD.
* Only integer values >= 1 are valid here.
*
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
@ -1184,12 +1183,6 @@
#define GRID_MAX_POINTS_X 5
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
// Set the boundaries for probing (where the probe can reach).
//#define LEFT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define RIGHT_PROBE_BED_POSITION (X_BED_SIZE - (MIN_PROBE_EDGE))
//#define FRONT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define BACK_PROBE_BED_POSITION (Y_BED_SIZE - (MIN_PROBE_EDGE))
// Probe along the Y axis, advancing X after each column
//#define PROBE_Y_FIRST

19
config/examples/Geeetech/GT2560/Configuration.h
View File

@ -903,11 +903,10 @@
/**
* Z Probe to nozzle (X,Y) offset, relative to (0, 0).
* X and Y offsets must be integers.
*
* In the following example the X and Y offsets are both positive:
* #define X_PROBE_OFFSET_FROM_EXTRUDER 10
* #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
*
* #define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
*
* +-- BACK ---+
* | |
@ -919,10 +918,10 @@
* | |
* O-- FRONT --+
* (0,0)
*
* Specify a Probe position as { X, Y, Z }
*/
#define X_PROBE_OFFSET_FROM_EXTRUDER 10 // X offset: -left +right [of the nozzle]
#define Y_PROBE_OFFSET_FROM_EXTRUDER 10 // Y offset: -front +behind [the nozzle]
#define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle]
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
// Certain types of probes need to stay away from edges
#define MIN_PROBE_EDGE 10
@ -956,7 +955,7 @@
*
* Use these settings to specify the distance (mm) to raise the probe (or
* lower the bed). The values set here apply over and above any (negative)
* probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
* probe Z Offset set with NOZZLE_TO_PROBE_OFFSET, M851, or the LCD.
* Only integer values >= 1 are valid here.
*
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
@ -1214,12 +1213,6 @@
#define GRID_MAX_POINTS_X 3
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
// Set the boundaries for probing (where the probe can reach).
//#define LEFT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define RIGHT_PROBE_BED_POSITION (X_BED_SIZE - (MIN_PROBE_EDGE))
//#define FRONT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define BACK_PROBE_BED_POSITION (Y_BED_SIZE - (MIN_PROBE_EDGE))
// Probe along the Y axis, advancing X after each column
//#define PROBE_Y_FIRST

19
config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h
View File

@ -888,11 +888,10 @@
/**
* Z Probe to nozzle (X,Y) offset, relative to (0, 0).
* X and Y offsets must be integers.
*
* In the following example the X and Y offsets are both positive:
* #define X_PROBE_OFFSET_FROM_EXTRUDER 10
* #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
*
* #define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
*
* +-- BACK ---+
* | |
@ -904,10 +903,10 @@
* | |
* O-- FRONT --+
* (0,0)
*
* Specify a Probe position as { X, Y, Z }
*/
#define X_PROBE_OFFSET_FROM_EXTRUDER 10 // X offset: -left +right [of the nozzle]
#define Y_PROBE_OFFSET_FROM_EXTRUDER 10 // Y offset: -front +behind [the nozzle]
#define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle]
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
// Certain types of probes need to stay away from edges
#define MIN_PROBE_EDGE 8
@ -941,7 +940,7 @@
*
* Use these settings to specify the distance (mm) to raise the probe (or
* lower the bed). The values set here apply over and above any (negative)
* probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
* probe Z Offset set with NOZZLE_TO_PROBE_OFFSET, M851, or the LCD.
* Only integer values >= 1 are valid here.
*
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
@ -1199,12 +1198,6 @@
#define GRID_MAX_POINTS_X 3
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
// Set the boundaries for probing (where the probe can reach).
//#define LEFT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define RIGHT_PROBE_BED_POSITION (X_BED_SIZE - (MIN_PROBE_EDGE))
//#define FRONT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define BACK_PROBE_BED_POSITION (Y_BED_SIZE - (MIN_PROBE_EDGE))
// Probe along the Y axis, advancing X after each column
//#define PROBE_Y_FIRST

19
config/examples/Geeetech/MeCreator2/Configuration.h
View File

@ -895,11 +895,10 @@
/**
* Z Probe to nozzle (X,Y) offset, relative to (0, 0).
* X and Y offsets must be integers.
*
* In the following example the X and Y offsets are both positive:
* #define X_PROBE_OFFSET_FROM_EXTRUDER 10
* #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
*
* #define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
*
* +-- BACK ---+
* | |
@ -911,10 +910,10 @@
* | |
* O-- FRONT --+
* (0,0)
*
* Specify a Probe position as { X, Y, Z }
*/
#define X_PROBE_OFFSET_FROM_EXTRUDER 10 // X offset: -left +right [of the nozzle]
#define Y_PROBE_OFFSET_FROM_EXTRUDER 10 // Y offset: -front +behind [the nozzle]
#define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle]
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
// Certain types of probes need to stay away from edges
#define MIN_PROBE_EDGE 10
@ -948,7 +947,7 @@
*
* Use these settings to specify the distance (mm) to raise the probe (or
* lower the bed). The values set here apply over and above any (negative)
* probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
* probe Z Offset set with NOZZLE_TO_PROBE_OFFSET, M851, or the LCD.
* Only integer values >= 1 are valid here.
*
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
@ -1206,12 +1205,6 @@
#define GRID_MAX_POINTS_X 3
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
// Set the boundaries for probing (where the probe can reach).
//#define LEFT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define RIGHT_PROBE_BED_POSITION (X_BED_SIZE - (MIN_PROBE_EDGE))
//#define FRONT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define BACK_PROBE_BED_POSITION (Y_BED_SIZE - (MIN_PROBE_EDGE))
// Probe along the Y axis, advancing X after each column
//#define PROBE_Y_FIRST

19
config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h
View File

@ -909,11 +909,10 @@
/**
* Z Probe to nozzle (X,Y) offset, relative to (0, 0).
* X and Y offsets must be integers.
*
* In the following example the X and Y offsets are both positive:
* #define X_PROBE_OFFSET_FROM_EXTRUDER 10
* #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
*
* #define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
*
* +-- BACK ---+
* | |
@ -925,10 +924,10 @@
* | |
* O-- FRONT --+
* (0,0)
*
* Specify a Probe position as { X, Y, Z }
*/
#define X_PROBE_OFFSET_FROM_EXTRUDER 4 // X offset: -left +right [of the nozzle]
#define Y_PROBE_OFFSET_FROM_EXTRUDER -44 // Y offset: -front +behind [the nozzle]
#define Z_PROBE_OFFSET_FROM_EXTRUDER -1.4 // Z offset: -below +above [the nozzle]
#define NOZZLE_TO_PROBE_OFFSET { 4, -44, -1.4 }
// Certain types of probes need to stay away from edges
#define MIN_PROBE_EDGE 10
@ -962,7 +961,7 @@
*
* Use these settings to specify the distance (mm) to raise the probe (or
* lower the bed). The values set here apply over and above any (negative)
* probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
* probe Z Offset set with NOZZLE_TO_PROBE_OFFSET, M851, or the LCD.
* Only integer values >= 1 are valid here.
*
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
@ -1220,12 +1219,6 @@
#define GRID_MAX_POINTS_X 4
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
// Set the boundaries for probing (where the probe can reach).
//#define LEFT_PROBE_BED_POSITION 10
//#define RIGHT_PROBE_BED_POSITION (X_MAX_POS - X_PROBE_OFFSET_FROM_EXTRUDER - 14)
//#define FRONT_PROBE_BED_POSITION 15
//#define BACK_PROBE_BED_POSITION (Y_MAX_POS + Y_PROBE_OFFSET_FROM_EXTRUDER - 25)
// Probe along the Y axis, advancing X after each column
//#define PROBE_Y_FIRST

19
config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h
View File

@ -908,11 +908,10 @@
/**
* Z Probe to nozzle (X,Y) offset, relative to (0, 0).
* X and Y offsets must be integers.
*
* In the following example the X and Y offsets are both positive:
* #define X_PROBE_OFFSET_FROM_EXTRUDER 10
* #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
*
* #define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
*
* +-- BACK ---+
* | |
@ -924,10 +923,10 @@
* | |
* O-- FRONT --+
* (0,0)
*
* Specify a Probe position as { X, Y, Z }
*/
#define X_PROBE_OFFSET_FROM_EXTRUDER 10 // X offset: -left +right [of the nozzle]
#define Y_PROBE_OFFSET_FROM_EXTRUDER 10 // Y offset: -front +behind [the nozzle]
#define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle]
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
// Certain types of probes need to stay away from edges
#define MIN_PROBE_EDGE 10
@ -961,7 +960,7 @@
*
* Use these settings to specify the distance (mm) to raise the probe (or
* lower the bed). The values set here apply over and above any (negative)
* probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
* probe Z Offset set with NOZZLE_TO_PROBE_OFFSET, M851, or the LCD.
* Only integer values >= 1 are valid here.
*
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
@ -1219,12 +1218,6 @@
#define GRID_MAX_POINTS_X 4
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
// Set the boundaries for probing (where the probe can reach).
//#define LEFT_PROBE_BED_POSITION 10
//#define RIGHT_PROBE_BED_POSITION (X_MAX_POS - X_PROBE_OFFSET_FROM_EXTRUDER - 14)
//#define FRONT_PROBE_BED_POSITION 15
//#define BACK_PROBE_BED_POSITION (Y_MAX_POS + Y_PROBE_OFFSET_FROM_EXTRUDER - 25)
// Probe along the Y axis, advancing X after each column
//#define PROBE_Y_FIRST

19
config/examples/Geeetech/Prusa i3 Pro C/Configuration.h
View File

@ -888,11 +888,10 @@
/**
* Z Probe to nozzle (X,Y) offset, relative to (0, 0).
* X and Y offsets must be integers.
*
* In the following example the X and Y offsets are both positive:
* #define X_PROBE_OFFSET_FROM_EXTRUDER 10
* #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
*
* #define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
*
* +-- BACK ---+
* | |
@ -904,10 +903,10 @@
* | |
* O-- FRONT --+
* (0,0)
*
* Specify a Probe position as { X, Y, Z }
*/
#define X_PROBE_OFFSET_FROM_EXTRUDER 10 // X offset: -left +right [of the nozzle]
#define Y_PROBE_OFFSET_FROM_EXTRUDER 10 // Y offset: -front +behind [the nozzle]
#define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle]
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
// Certain types of probes need to stay away from edges
#define MIN_PROBE_EDGE 10
@ -941,7 +940,7 @@
*
* Use these settings to specify the distance (mm) to raise the probe (or
* lower the bed). The values set here apply over and above any (negative)
* probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
* probe Z Offset set with NOZZLE_TO_PROBE_OFFSET, M851, or the LCD.
* Only integer values >= 1 are valid here.
*
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
@ -1199,12 +1198,6 @@
#define GRID_MAX_POINTS_X 3
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
// Set the boundaries for probing (where the probe can reach).
//#define LEFT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define RIGHT_PROBE_BED_POSITION (X_BED_SIZE - (MIN_PROBE_EDGE))
//#define FRONT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define BACK_PROBE_BED_POSITION (Y_BED_SIZE - (MIN_PROBE_EDGE))
// Probe along the Y axis, advancing X after each column
//#define PROBE_Y_FIRST

19
config/examples/Geeetech/Prusa i3 Pro W/Configuration.h
View File

@ -888,11 +888,10 @@
/**
* Z Probe to nozzle (X,Y) offset, relative to (0, 0).
* X and Y offsets must be integers.
*
* In the following example the X and Y offsets are both positive:
* #define X_PROBE_OFFSET_FROM_EXTRUDER 10
* #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
*
* #define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
*
* +-- BACK ---+
* | |
@ -904,10 +903,10 @@
* | |
* O-- FRONT --+
* (0,0)
*
* Specify a Probe position as { X, Y, Z }
*/
#define X_PROBE_OFFSET_FROM_EXTRUDER 10 // X offset: -left +right [of the nozzle]
#define Y_PROBE_OFFSET_FROM_EXTRUDER 10 // Y offset: -front +behind [the nozzle]
#define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle]
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
// Certain types of probes need to stay away from edges
#define MIN_PROBE_EDGE 10
@ -941,7 +940,7 @@
*
* Use these settings to specify the distance (mm) to raise the probe (or
* lower the bed). The values set here apply over and above any (negative)
* probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
* probe Z Offset set with NOZZLE_TO_PROBE_OFFSET, M851, or the LCD.
* Only integer values >= 1 are valid here.
*
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
@ -1199,12 +1198,6 @@
#define GRID_MAX_POINTS_X 3
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
// Set the boundaries for probing (where the probe can reach).
//#define LEFT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define RIGHT_PROBE_BED_POSITION (X_BED_SIZE - (MIN_PROBE_EDGE))
//#define FRONT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define BACK_PROBE_BED_POSITION (Y_BED_SIZE - (MIN_PROBE_EDGE))
// Probe along the Y axis, advancing X after each column
//#define PROBE_Y_FIRST

19
config/examples/HMS434/Configuration.h
View File

@ -875,11 +875,10 @@
/**
* Z Probe to nozzle (X,Y) offset, relative to (0, 0).
* X and Y offsets must be integers.
*
* In the following example the X and Y offsets are both positive:
* #define X_PROBE_OFFSET_FROM_EXTRUDER 10
* #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
*
* #define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
*
* +-- BACK ---+
* | |
@ -891,10 +890,10 @@
* | |
* O-- FRONT --+
* (0,0)
*
* Specify a Probe position as { X, Y, Z }
*/
#define X_PROBE_OFFSET_FROM_EXTRUDER -21 // X offset: -left +right [of the nozzle]
#define Y_PROBE_OFFSET_FROM_EXTRUDER 22 // Y offset: -front +behind [the nozzle]
#define Z_PROBE_OFFSET_FROM_EXTRUDER -1.54 // Z offset: -below +above [the nozzle]
#define NOZZLE_TO_PROBE_OFFSET { -21, 22, -1.54 }
// Certain types of probes need to stay away from edges
#define MIN_PROBE_EDGE 20
@ -928,7 +927,7 @@
*
* Use these settings to specify the distance (mm) to raise the probe (or
* lower the bed). The values set here apply over and above any (negative)
* probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
* probe Z Offset set with NOZZLE_TO_PROBE_OFFSET, M851, or the LCD.
* Only integer values >= 1 are valid here.
*
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
@ -1186,12 +1185,6 @@
#define GRID_MAX_POINTS_X 5
#define GRID_MAX_POINTS_Y 3
// Set the boundaries for probing (where the probe can reach).
//#define LEFT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define RIGHT_PROBE_BED_POSITION (X_BED_SIZE - (MIN_PROBE_EDGE))
//#define FRONT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define BACK_PROBE_BED_POSITION (Y_BED_SIZE - (MIN_PROBE_EDGE))
// Probe along the Y axis, advancing X after each column
//#define PROBE_Y_FIRST

19
config/examples/Infitary/i3-M508/Configuration.h
View File

@ -892,11 +892,10 @@
/**
* Z Probe to nozzle (X,Y) offset, relative to (0, 0).
* X and Y offsets must be integers.
*
* In the following example the X and Y offsets are both positive:
* #define X_PROBE_OFFSET_FROM_EXTRUDER 10
* #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
*
* #define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
*
* +-- BACK ---+
* | |
@ -908,10 +907,10 @@
* | |
* O-- FRONT --+
* (0,0)
*
* Specify a Probe position as { X, Y, Z }
*/
#define X_PROBE_OFFSET_FROM_EXTRUDER 10 // X offset: -left +right [of the nozzle]
#define Y_PROBE_OFFSET_FROM_EXTRUDER 10 // Y offset: -front +behind [the nozzle]
#define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle]
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
// Certain types of probes need to stay away from edges
#define MIN_PROBE_EDGE 10
@ -945,7 +944,7 @@
*
* Use these settings to specify the distance (mm) to raise the probe (or
* lower the bed). The values set here apply over and above any (negative)
* probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
* probe Z Offset set with NOZZLE_TO_PROBE_OFFSET, M851, or the LCD.
* Only integer values >= 1 are valid here.
*
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
@ -1203,12 +1202,6 @@
#define GRID_MAX_POINTS_X 3
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
// Set the boundaries for probing (where the probe can reach).
//#define LEFT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define RIGHT_PROBE_BED_POSITION (X_BED_SIZE - (MIN_PROBE_EDGE))
//#define FRONT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define BACK_PROBE_BED_POSITION (Y_BED_SIZE - (MIN_PROBE_EDGE))
// Probe along the Y axis, advancing X after each column
//#define PROBE_Y_FIRST

19
config/examples/JGAurora/A1/Configuration.h
View File

@ -895,11 +895,10 @@
/**
* Z Probe to nozzle (X,Y) offset, relative to (0, 0).
* X and Y offsets must be integers.
*
* In the following example the X and Y offsets are both positive:
* #define X_PROBE_OFFSET_FROM_EXTRUDER 10
* #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
*
* #define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
*
* +-- BACK ---+
* | |
@ -911,10 +910,10 @@
* | |
* O-- FRONT --+
* (0,0)
*
* Specify a Probe position as { X, Y, Z }
*/
#define X_PROBE_OFFSET_FROM_EXTRUDER 10 // X offset: -left +right [of the nozzle]
#define Y_PROBE_OFFSET_FROM_EXTRUDER 10 // Y offset: -front +behind [the nozzle]
#define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle]
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
// Certain types of probes need to stay away from edges
#define MIN_PROBE_EDGE 10
@ -948,7 +947,7 @@
*
* Use these settings to specify the distance (mm) to raise the probe (or
* lower the bed). The values set here apply over and above any (negative)
* probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
* probe Z Offset set with NOZZLE_TO_PROBE_OFFSET, M851, or the LCD.
* Only integer values >= 1 are valid here.
*
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
@ -1206,12 +1205,6 @@
#define GRID_MAX_POINTS_X 3
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
// Set the boundaries for probing (where the probe can reach).
//#define LEFT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define RIGHT_PROBE_BED_POSITION (X_BED_SIZE - (MIN_PROBE_EDGE))
//#define FRONT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define BACK_PROBE_BED_POSITION (Y_BED_SIZE - (MIN_PROBE_EDGE))
// Probe along the Y axis, advancing X after each column
//#define PROBE_Y_FIRST

19
config/examples/JGAurora/A5/Configuration.h
View File

@ -900,11 +900,10 @@
/**
* Z Probe to nozzle (X,Y) offset, relative to (0, 0).
* X and Y offsets must be integers.
*
* In the following example the X and Y offsets are both positive:
* #define X_PROBE_OFFSET_FROM_EXTRUDER 10
* #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
*
* #define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
*
* +-- BACK ---+
* | |
@ -916,10 +915,10 @@
* | |
* O-- FRONT --+
* (0,0)
*
* Specify a Probe position as { X, Y, Z }
*/
#define X_PROBE_OFFSET_FROM_EXTRUDER 10 // X offset: -left +right [of the nozzle]
#define Y_PROBE_OFFSET_FROM_EXTRUDER 10 // Y offset: -front +behind [the nozzle]
#define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle]
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
// Certain types of probes need to stay away from edges
#define MIN_PROBE_EDGE 10
@ -953,7 +952,7 @@
*
* Use these settings to specify the distance (mm) to raise the probe (or
* lower the bed). The values set here apply over and above any (negative)
* probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
* probe Z Offset set with NOZZLE_TO_PROBE_OFFSET, M851, or the LCD.
* Only integer values >= 1 are valid here.
*
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
@ -1211,12 +1210,6 @@
#define GRID_MAX_POINTS_X 5
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
// Set the boundaries for probing (where the probe can reach).
//#define LEFT_PROBE_BED_POSITION 15
//#define RIGHT_PROBE_BED_POSITION 170
//#define FRONT_PROBE_BED_POSITION 20
//#define BACK_PROBE_BED_POSITION 170
// Probe along the Y axis, advancing X after each column
//#define PROBE_Y_FIRST

19
config/examples/JGAurora/A5S/Configuration.h
View File

@ -895,11 +895,10 @@
/**
* Z Probe to nozzle (X,Y) offset, relative to (0, 0).
* X and Y offsets must be integers.
*
* In the following example the X and Y offsets are both positive:
* #define X_PROBE_OFFSET_FROM_EXTRUDER 10
* #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
*
* #define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
*
* +-- BACK ---+
* | |
@ -911,10 +910,10 @@
* | |
* O-- FRONT --+
* (0,0)
*
* Specify a Probe position as { X, Y, Z }
*/
#define X_PROBE_OFFSET_FROM_EXTRUDER 10 // X offset: -left +right [of the nozzle]
#define Y_PROBE_OFFSET_FROM_EXTRUDER 10 // Y offset: -front +behind [the nozzle]
#define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle]
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
// Certain types of probes need to stay away from edges
#define MIN_PROBE_EDGE 10
@ -948,7 +947,7 @@
*
* Use these settings to specify the distance (mm) to raise the probe (or
* lower the bed). The values set here apply over and above any (negative)
* probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
* probe Z Offset set with NOZZLE_TO_PROBE_OFFSET, M851, or the LCD.
* Only integer values >= 1 are valid here.
*
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
@ -1206,12 +1205,6 @@
#define GRID_MAX_POINTS_X 3
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
// Set the boundaries for probing (where the probe can reach).
//#define LEFT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define RIGHT_PROBE_BED_POSITION (X_BED_SIZE - (MIN_PROBE_EDGE))
//#define FRONT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define BACK_PROBE_BED_POSITION (Y_BED_SIZE - (MIN_PROBE_EDGE))
// Probe along the Y axis, advancing X after each column
//#define PROBE_Y_FIRST

19
config/examples/MakerParts/Configuration.h
View File

@ -908,11 +908,10 @@
/**
* Z Probe to nozzle (X,Y) offset, relative to (0, 0).
* X and Y offsets must be integers.
*
* In the following example the X and Y offsets are both positive:
* #define X_PROBE_OFFSET_FROM_EXTRUDER 10
* #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
*
* #define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
*
* +-- BACK ---+
* | |
@ -924,10 +923,10 @@
* | |
* O-- FRONT --+
* (0,0)
*
* Specify a Probe position as { X, Y, Z }
*/
#define X_PROBE_OFFSET_FROM_EXTRUDER 10 // X offset: -left +right [of the nozzle]
#define Y_PROBE_OFFSET_FROM_EXTRUDER 10 // Y offset: -front +behind [the nozzle]
#define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle]
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
// Certain types of probes need to stay away from edges
#define MIN_PROBE_EDGE 10
@ -961,7 +960,7 @@
*
* Use these settings to specify the distance (mm) to raise the probe (or
* lower the bed). The values set here apply over and above any (negative)
* probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
* probe Z Offset set with NOZZLE_TO_PROBE_OFFSET, M851, or the LCD.
* Only integer values >= 1 are valid here.
*
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
@ -1219,12 +1218,6 @@
#define GRID_MAX_POINTS_X 3
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
// Set the boundaries for probing (where the probe can reach).
//#define LEFT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define RIGHT_PROBE_BED_POSITION (X_BED_SIZE - (MIN_PROBE_EDGE))
//#define FRONT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define BACK_PROBE_BED_POSITION (Y_BED_SIZE - (MIN_PROBE_EDGE))
// Probe along the Y axis, advancing X after each column
//#define PROBE_Y_FIRST

19
config/examples/Malyan/M150/Configuration.h
View File

@ -908,11 +908,10 @@
/**
* Z Probe to nozzle (X,Y) offset, relative to (0, 0).
* X and Y offsets must be integers.
*
* In the following example the X and Y offsets are both positive:
* #define X_PROBE_OFFSET_FROM_EXTRUDER 10
* #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
*
* #define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
*
* +-- BACK ---+
* | |
@ -924,14 +923,14 @@
* | |
* O-- FRONT --+
* (0,0)
*
* Specify a Probe position as { X, Y, Z }
*/
// Set for HoolyHoo's probe mount
// http://www.thingiverse.com/thing:1960419
// Note: HoolyHoo mount is X=35, Y=-50.
//#define X_PROBE_OFFSET_FROM_EXTRUDER 35 // X offset: -left +right [of the nozzle]
//#define Y_PROBE_OFFSET_FROM_EXTRUDER -50 // Y offset: -front +behind [the nozzle]
//#define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle]
//#define NOZZLE_TO_PROBE_OFFSET { 35, -50, 0 }
// Certain types of probes need to stay away from edges
#define MIN_PROBE_EDGE 10
@ -965,7 +964,7 @@
*
* Use these settings to specify the distance (mm) to raise the probe (or
* lower the bed). The values set here apply over and above any (negative)
* probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
* probe Z Offset set with NOZZLE_TO_PROBE_OFFSET, M851, or the LCD.
* Only integer values >= 1 are valid here.
*
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
@ -1227,12 +1226,6 @@
#define GRID_MAX_POINTS_X 3
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
// Set the boundaries for probing (where the probe can reach).
//#define LEFT_PROBE_BED_POSITION 50
//#define RIGHT_PROBE_BED_POSITION 150
//#define FRONT_PROBE_BED_POSITION 50
//#define BACK_PROBE_BED_POSITION 150
// Probe along the Y axis, advancing X after each column
//#define PROBE_Y_FIRST

19
config/examples/Malyan/M200/Configuration.h
View File

@ -887,11 +887,10 @@
/**
* Z Probe to nozzle (X,Y) offset, relative to (0, 0).
* X and Y offsets must be integers.
*
* In the following example the X and Y offsets are both positive:
* #define X_PROBE_OFFSET_FROM_EXTRUDER 10
* #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
*
* #define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
*
* +-- BACK ---+
* | |
@ -903,10 +902,10 @@
* | |
* O-- FRONT --+
* (0,0)
*
* Specify a Probe position as { X, Y, Z }
*/
#define X_PROBE_OFFSET_FROM_EXTRUDER 10 // X offset: -left +right [of the nozzle]
#define Y_PROBE_OFFSET_FROM_EXTRUDER 10 // Y offset: -front +behind [the nozzle]
#define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle]
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
// Certain types of probes need to stay away from edges
#define MIN_PROBE_EDGE 10
@ -940,7 +939,7 @@
*
* Use these settings to specify the distance (mm) to raise the probe (or
* lower the bed). The values set here apply over and above any (negative)
* probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
* probe Z Offset set with NOZZLE_TO_PROBE_OFFSET, M851, or the LCD.
* Only integer values >= 1 are valid here.
*
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
@ -1198,12 +1197,6 @@
#define GRID_MAX_POINTS_X 3
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
// Set the boundaries for probing (where the probe can reach).
//#define LEFT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define RIGHT_PROBE_BED_POSITION (X_BED_SIZE - (MIN_PROBE_EDGE))
//#define FRONT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define BACK_PROBE_BED_POSITION (Y_BED_SIZE - (MIN_PROBE_EDGE))
// Probe along the Y axis, advancing X after each column
//#define PROBE_Y_FIRST

19
config/examples/Micromake/C1/basic/Configuration.h
View File

@ -892,11 +892,10 @@
/**
* Z Probe to nozzle (X,Y) offset, relative to (0, 0).
* X and Y offsets must be integers.
*
* In the following example the X and Y offsets are both positive:
* #define X_PROBE_OFFSET_FROM_EXTRUDER 10
* #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
*
* #define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
*
* +-- BACK ---+
* | |
@ -908,10 +907,10 @@
* | |
* O-- FRONT --+
* (0,0)
*
* Specify a Probe position as { X, Y, Z }
*/
#define X_PROBE_OFFSET_FROM_EXTRUDER 0 // X offset: -left +right [of the nozzle]
#define Y_PROBE_OFFSET_FROM_EXTRUDER 0 // Y offset: -front +behind [the nozzle]
#define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle]
#define NOZZLE_TO_PROBE_OFFSET { 0, 0, 0 }
// Certain types of probes need to stay away from edges
#define MIN_PROBE_EDGE 10
@ -945,7 +944,7 @@
*
* Use these settings to specify the distance (mm) to raise the probe (or
* lower the bed). The values set here apply over and above any (negative)
* probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
* probe Z Offset set with NOZZLE_TO_PROBE_OFFSET, M851, or the LCD.
* Only integer values >= 1 are valid here.
*
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
@ -1203,12 +1202,6 @@
#define GRID_MAX_POINTS_X 3
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
// Set the boundaries for probing (where the probe can reach).
//#define LEFT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define RIGHT_PROBE_BED_POSITION (X_BED_SIZE - (MIN_PROBE_EDGE))
//#define FRONT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define BACK_PROBE_BED_POSITION (Y_BED_SIZE - (MIN_PROBE_EDGE))
// Probe along the Y axis, advancing X after each column
//#define PROBE_Y_FIRST

19
config/examples/Micromake/C1/enhanced/Configuration.h
View File

@ -892,11 +892,10 @@
/**
* Z Probe to nozzle (X,Y) offset, relative to (0, 0).
* X and Y offsets must be integers.
*
* In the following example the X and Y offsets are both positive:
* #define X_PROBE_OFFSET_FROM_EXTRUDER 10
* #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
*
* #define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
*
* +-- BACK ---+
* | |
@ -908,10 +907,10 @@
* | |
* O-- FRONT --+
* (0,0)
*
* Specify a Probe position as { X, Y, Z }
*/
#define X_PROBE_OFFSET_FROM_EXTRUDER 0 // X offset: -left +right [of the nozzle]
#define Y_PROBE_OFFSET_FROM_EXTRUDER 0 // Y offset: -front +behind [the nozzle]
#define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle]
#define NOZZLE_TO_PROBE_OFFSET { 0, 0, 0 }
// Certain types of probes need to stay away from edges
#define MIN_PROBE_EDGE 10
@ -945,7 +944,7 @@
*
* Use these settings to specify the distance (mm) to raise the probe (or
* lower the bed). The values set here apply over and above any (negative)
* probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
* probe Z Offset set with NOZZLE_TO_PROBE_OFFSET, M851, or the LCD.
* Only integer values >= 1 are valid here.
*
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
@ -1203,12 +1202,6 @@
#define GRID_MAX_POINTS_X 3
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
// Set the boundaries for probing (where the probe can reach).
//#define LEFT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define RIGHT_PROBE_BED_POSITION (X_BED_SIZE - (MIN_PROBE_EDGE))
//#define FRONT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define BACK_PROBE_BED_POSITION (Y_BED_SIZE - (MIN_PROBE_EDGE))
// Probe along the Y axis, advancing X after each column
//#define PROBE_Y_FIRST

19
config/examples/Mks/Robin/Configuration.h
View File

@ -889,11 +889,10 @@
/**
* Z Probe to nozzle (X,Y) offset, relative to (0, 0).
* X and Y offsets must be integers.
*
* In the following example the X and Y offsets are both positive:
* #define X_PROBE_OFFSET_FROM_EXTRUDER 10
* #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
*
* #define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
*
* +-- BACK ---+
* | |
@ -905,10 +904,10 @@
* | |
* O-- FRONT --+
* (0,0)
*
* Specify a Probe position as { X, Y, Z }
*/
#define X_PROBE_OFFSET_FROM_EXTRUDER 10 // X offset: -left +right [of the nozzle]
#define Y_PROBE_OFFSET_FROM_EXTRUDER 10 // Y offset: -front +behind [the nozzle]
#define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle]
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
// Certain types of probes need to stay away from edges
#define MIN_PROBE_EDGE 10
@ -942,7 +941,7 @@
*
* Use these settings to specify the distance (mm) to raise the probe (or
* lower the bed). The values set here apply over and above any (negative)
* probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
* probe Z Offset set with NOZZLE_TO_PROBE_OFFSET, M851, or the LCD.
* Only integer values >= 1 are valid here.
*
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
@ -1200,12 +1199,6 @@
#define GRID_MAX_POINTS_X 3
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
// Set the boundaries for probing (where the probe can reach).
//#define LEFT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define RIGHT_PROBE_BED_POSITION (X_BED_SIZE - (MIN_PROBE_EDGE))
//#define FRONT_PROBE_BED_POSITION MIN_PROBE_EDGE
//#define BACK_PROBE_BED_POSITION (Y_BED_SIZE - (MIN_PROBE_EDGE))
// Probe along the Y axis, advancing X after each column
//#define PROBE_Y_FIRST

Some files were not shown because too many files have changed in this diff Show More