bissen21/Marlin_Firmware
1
0
Fork 0
Code Issues Pull Requests Projects Releases 4 Wiki Activity

SPINDLE_LASER_ENABLE => SPINDLE_LASER_ENA

Browse Source
This commit is contained in:
Scott Lahteine
2019-04-08 17:52:33 -05:00
parent 9abe9aff56
commit c8a83fb122
51 changed files with 90 additions and 88 deletions
Download Patch File Download Diff File Expand all files Collapse all files

12
Marlin/src/gcode/control/M3-M5.cpp
View File

@ -53,7 +53,7 @@ uint8_t spindle_laser_power; // = 0
* NOTE: A minimum PWM frequency of 50 Hz is needed. All prescaler
* factors for timers 2, 3, 4, and 5 are acceptable.
*
* SPINDLE_LASER_ENABLE_PIN needs an external pullup or it may power on
* SPINDLE_LASER_ENA_PIN needs an external pullup or it may power on
* the spindle/laser during power-up or when connecting to the host
* (usually goes through a reset which sets all I/O pins to tri-state)
*
@ -73,7 +73,7 @@ inline void delay_for_power_down() { safe_delay(SPINDLE_LASER_POWERDOWN_DELAY);
*/
inline void set_spindle_laser_ocr(const uint8_t ocr) {
WRITE(SPINDLE_LASER_ENABLE_PIN, SPINDLE_LASER_ENABLE_INVERT); // turn spindle on (active low)
WRITE(SPINDLE_LASER_ENA_PIN, SPINDLE_LASER_ENABLE_INVERT); // turn spindle on (active low)
analogWrite(SPINDLE_LASER_PWM_PIN, (SPINDLE_LASER_PWM_INVERT) ? 255 - ocr : ocr);
}
@ -81,7 +81,7 @@ inline void set_spindle_laser_ocr(const uint8_t ocr) {
void update_spindle_laser_power() {
if (spindle_laser_power == 0) {
WRITE(SPINDLE_LASER_ENABLE_PIN, !SPINDLE_LASER_ENABLE_INVERT); // turn spindle off (active low)
WRITE(SPINDLE_LASER_ENA_PIN, !SPINDLE_LASER_ENABLE_INVERT); // turn spindle off (active low)
analogWrite(SPINDLE_LASER_PWM_PIN, SPINDLE_LASER_PWM_INVERT ? 255 : 0); // only write low byte
delay_for_power_down();
}
@ -101,7 +101,7 @@ inline void set_spindle_laser_ocr(const uint8_t ocr) {
#endif // SPINDLE_LASER_PWM
bool spindle_laser_enabled() {
return !!spindle_laser_power; // READ(SPINDLE_LASER_ENABLE_PIN) == SPINDLE_LASER_ENABLE_INVERT;
return !!spindle_laser_power; // READ(SPINDLE_LASER_ENA_PIN) == SPINDLE_LASER_ENABLE_INVERT;
}
void set_spindle_laser_enabled(const bool enable) {
@ -111,11 +111,11 @@ void set_spindle_laser_enabled(const bool enable) {
update_spindle_laser_power();
#else
if (enable) {
WRITE(SPINDLE_LASER_ENABLE_PIN, SPINDLE_LASER_ENABLE_INVERT);
WRITE(SPINDLE_LASER_ENA_PIN, SPINDLE_LASER_ENABLE_INVERT);
delay_for_power_up();
}
else {
WRITE(SPINDLE_LASER_ENABLE_PIN, !SPINDLE_LASER_ENABLE_INVERT);
WRITE(SPINDLE_LASER_ENA_PIN, !SPINDLE_LASER_ENABLE_INVERT);
delay_for_power_down();
}
#endif