Balance CI tests (#20485)

This commit is contained in:
Jason Smith 2020-12-17 04:18:07 -08:00 committed by Scott Lahteine
parent e5d094d2bd
commit c3a1cd10ab
10 changed files with 125 additions and 149 deletions

View File

@ -1916,7 +1916,7 @@ static_assert(hbm[Z_AXIS] >= 0, "HOMING_BUMP_MM.Z must be greater than or equal
/**
* LED Backlight Timeout
*/
#if defined(LED_BACKLIGHT_TIMEOUT) && !(ENABLED(PSU_CONTROL) && EITHER(FYSETC_MINI_12864_2_0, FYSETC_MINI_12864_2_1))
#if defined(LED_BACKLIGHT_TIMEOUT) && !(ENABLED(PSU_CONTROL) && ANY(FYSETC_MINI_12864_2_0, FYSETC_MINI_12864_2_1, FYSETC_242_OLED_12864))
#error "LED_BACKLIGHT_TIMEOUT requires a FYSETC Mini Panel and a Power Switch."
#endif

View File

@ -226,7 +226,7 @@
#define DOGLCD_SCK 17
#define DOGLCD_A0 LCD_PINS_DC
#define KILL_PIN -1 // NC
#undef KILL_PIN
#define NEOPIXEL_PIN 27
#else
@ -243,7 +243,6 @@
#define LCD_BACKLIGHT_PIN 27
#endif
#define KILL_PIN 41
#define LCD_RESET_PIN 23 // Must be high or open for LCD to operate normally.
// Seems to work best if left open.

View File

@ -14,5 +14,66 @@ opt_set MOTHERBOARD BOARD_FYSETC_F6_13
opt_enable DGUS_LCD_UI_FYSETC
exec_test $1 $2 "FYSETC F6 1.3 with DGUS" "$3"
#
# Delta Config (generic) + UBL + ALLEN_KEY + EEPROM_SETTINGS + OLED_PANEL_TINYBOY2
#
use_example_configs delta/generic
opt_set MOTHERBOARD BOARD_FYSETC_F6_13
opt_enable RESTORE_LEVELING_AFTER_G28 EEPROM_SETTINGS EEPROM_CHITCHAT \
Z_PROBE_ALLEN_KEY AUTO_BED_LEVELING_UBL \
OLED_PANEL_TINYBOY2 MESH_EDIT_GFX_OVERLAY DELTA_CALIBRATION_MENU
opt_set LCD_LANGUAGE ko_KR
opt_set X_DRIVER_TYPE L6470
opt_set Y_DRIVER_TYPE L6470
opt_set Z_DRIVER_TYPE L6470
opt_add L6470_CHAIN_SCK_PIN 53
opt_add L6470_CHAIN_MISO_PIN 49
opt_add L6470_CHAIN_MOSI_PIN 40
opt_add L6470_CHAIN_SS_PIN 42
opt_add "ENABLE_RESET_L64XX_CHIPS(V) NOOP"
exec_test $1 $2 "DELTA, RAMPS, L6470, UBL, Allen Key, EEPROM, OLED_PANEL_TINYBOY2..." "$3"
#
# Test mixed TMC config
#
restore_configs
opt_set MOTHERBOARD BOARD_FYSETC_F6_13
opt_set LCD_LANGUAGE vi
opt_set X_DRIVER_TYPE TMC2160
opt_set Y_DRIVER_TYPE TMC5160
opt_set Z_DRIVER_TYPE TMC2208_STANDALONE
opt_set E0_DRIVER_TYPE TMC2130
opt_set X_MIN_ENDSTOP_INVERTING true
opt_set Y_MIN_ENDSTOP_INVERTING true
opt_enable REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER \
MARLIN_BRICKOUT MARLIN_INVADERS MARLIN_SNAKE \
MONITOR_DRIVER_STATUS STEALTHCHOP_XY STEALTHCHOP_Z STEALTHCHOP_E HYBRID_THRESHOLD \
USE_ZMIN_PLUG SENSORLESS_HOMING TMC_DEBUG M114_DETAIL
exec_test $1 $2 "RAMPS | Mixed TMC | Sensorless | RRDFGSC | Games" "$3"
#
# Delta Config (FLSUN AC because it's complex)
#
use_example_configs delta/FLSUN/auto_calibrate
opt_set MOTHERBOARD BOARD_FYSETC_F6_13
exec_test $1 $2 "RAMPS 1.3 | DELTA | FLSUN AC Config" "$3"
#
# SCARA with Mixed TMC
#
use_example_configs SCARA/Morgan
opt_set MOTHERBOARD BOARD_FYSETC_F6_13
opt_set LCD_LANGUAGE es
opt_enable USE_ZMIN_PLUG FIX_MOUNTED_PROBE AUTO_BED_LEVELING_BILINEAR PAUSE_BEFORE_DEPLOY_STOW \
FYSETC_242_OLED_12864 EEPROM_SETTINGS EEPROM_CHITCHAT M114_DETAIL Z_SAFE_HOMING \
STEALTHCHOP_XY STEALTHCHOP_Z STEALTHCHOP_E HYBRID_THRESHOLD SENSORLESS_HOMING SQUARE_WAVE_STEPPING
opt_set X_MAX_ENDSTOP_INVERTING false
opt_set X_DRIVER_TYPE TMC2209
opt_set Y_DRIVER_TYPE TMC2130
opt_set Z_DRIVER_TYPE TMC2130_STANDALONE
opt_set E0_DRIVER_TYPE TMC2660
opt_add X_HARDWARE_SERIAL Serial2
exec_test $1 $2 "FYSETC_F6 | SCARA | Mixed TMC | EEPROM" "$3"
# clean up
restore_configs

View File

@ -12,22 +12,6 @@ set -e
use_example_configs Azteeg/X5GT
exec_test $1 $2 "Azteeg X5GT Example Configuration" "$3"
restore_configs
opt_set MOTHERBOARD BOARD_SMOOTHIEBOARD
opt_set EXTRUDERS 2
opt_set TEMP_SENSOR_1 -1
opt_set TEMP_SENSOR_BED 5
opt_enable VIKI2 SDSUPPORT ADAPTIVE_FAN_SLOWING NO_FAN_SLOWING_IN_PID_TUNING \
FIX_MOUNTED_PROBE AUTO_BED_LEVELING_BILINEAR G29_RETRY_AND_RECOVER Z_MIN_PROBE_REPEATABILITY_TEST DEBUG_LEVELING_FEATURE \
LEVEL_BED_CORNERS LEVEL_CORNERS_USE_PROBE LEVEL_CORNERS_VERIFY_RAISED \
BABYSTEPPING BABYSTEP_XY BABYSTEP_ZPROBE_OFFSET BABYSTEP_ZPROBE_GFX_OVERLAY \
PRINTCOUNTER NOZZLE_PARK_FEATURE NOZZLE_CLEAN_FEATURE SLOW_PWM_HEATERS PIDTEMPBED EEPROM_SETTINGS INCH_MODE_SUPPORT TEMPERATURE_UNITS_SUPPORT \
Z_SAFE_HOMING ADVANCED_PAUSE_FEATURE PARK_HEAD_ON_PAUSE \
LCD_INFO_MENU ARC_SUPPORT BEZIER_CURVE_SUPPORT EXTENDED_CAPABILITIES_REPORT AUTO_REPORT_TEMPERATURES SDCARD_SORT_ALPHA EMERGENCY_PARSER
opt_disable SD_PROCEDURE_DEPTH
opt_set GRID_MAX_POINTS_X 16
exec_test $1 $2 "Smoothieboard with many features" "$3"
restore_configs
opt_set MOTHERBOARD BOARD_SMOOTHIEBOARD
opt_set EXTRUDERS 2
@ -35,12 +19,12 @@ opt_set TEMP_SENSOR_1 -1
opt_set TEMP_SENSOR_BED 5
opt_enable TFTGLCD_PANEL_SPI SDSUPPORT ADAPTIVE_FAN_SLOWING NO_FAN_SLOWING_IN_PID_TUNING \
FIX_MOUNTED_PROBE AUTO_BED_LEVELING_BILINEAR G29_RETRY_AND_RECOVER Z_MIN_PROBE_REPEATABILITY_TEST DEBUG_LEVELING_FEATURE \
BABYSTEPPING BABYSTEP_XY BABYSTEP_ZPROBE_OFFSET \
BABYSTEPPING BABYSTEP_XY BABYSTEP_ZPROBE_OFFSET LEVEL_CORNERS_USE_PROBE LEVEL_CORNERS_VERIFY_RAISED \
PRINTCOUNTER NOZZLE_PARK_FEATURE NOZZLE_CLEAN_FEATURE SLOW_PWM_HEATERS PIDTEMPBED EEPROM_SETTINGS INCH_MODE_SUPPORT TEMPERATURE_UNITS_SUPPORT \
Z_SAFE_HOMING ADVANCED_PAUSE_FEATURE PARK_HEAD_ON_PAUSE \
LCD_INFO_MENU ARC_SUPPORT BEZIER_CURVE_SUPPORT EXTENDED_CAPABILITIES_REPORT AUTO_REPORT_TEMPERATURES SDCARD_SORT_ALPHA EMERGENCY_PARSER
opt_set GRID_MAX_POINTS_X 16
exec_test $1 $2 "Smoothieboard with TFTGLCD_PANEL_SPI" "$3"
exec_test $1 $2 "Smoothieboard with TFTGLCD_PANEL_SPI and many features" "$3"
#restore_configs
#opt_set MOTHERBOARD BOARD_AZTEEG_X5_MINI_WIFI

View File

@ -60,21 +60,6 @@ opt_disable SEGMENT_LEVELED_MOVES
opt_enable BABYSTEPPING BABYSTEP_XY BABYSTEP_ZPROBE_OFFSET DOUBLECLICK_FOR_Z_BABYSTEPPING BABYSTEP_HOTEND_Z_OFFSET BABYSTEP_DISPLAY_TOTAL M114_DETAIL
exec_test $1 $2 "Azteeg X3 Pro | EXTRUDERS 5 | RRDFGSC | UBL | LIN_ADVANCE | Sled Probe | Skew | JP-Kana | Babystep offsets ..." "$3"
#
# Test a Servo Probe
# ...with AUTO_BED_LEVELING_3POINT, DEBUG_LEVELING_FEATURE, EEPROM_SETTINGS, EEPROM_CHITCHAT, EXTENDED_CAPABILITIES_REPORT, and AUTO_REPORT_TEMPERATURES
#
restore_configs
opt_set LCD_LANGUAGE zh_CN
opt_set MMU_MODEL PRUSA_MMU2S
opt_set EXTRUDERS 5
opt_set NUM_SERVOS 1
opt_enable ZONESTAR_LCD Z_PROBE_SERVO_NR Z_SERVO_ANGLES DEACTIVATE_SERVOS_AFTER_MOVE BOOT_MARLIN_LOGO_ANIMATED \
AUTO_BED_LEVELING_3POINT DEBUG_LEVELING_FEATURE EEPROM_SETTINGS EEPROM_CHITCHAT M114_DETAIL \
NO_VOLUMETRICS EXTENDED_CAPABILITIES_REPORT AUTO_REPORT_TEMPERATURES AUTOTEMP G38_PROBE_TARGET JOYSTICK \
MMU2_MENUS DIRECT_STEPPING DETECT_BROKEN_ENDSTOP \
FILAMENT_RUNOUT_SENSOR NOZZLE_PARK_FEATURE ADVANCED_PAUSE_FEATURE Z_SAFE_HOMING
exec_test $1 $2 "RAMPS | ZONESTAR + Chinese | MMU2S | Servo | 3-Point + Debug | G38 ..." "$3"
#
# 5 runout sensors with distinct states
@ -100,27 +85,6 @@ opt_set FIL_RUNOUT4_PIN 46
opt_set FIL_RUNOUT5_PIN 47
exec_test $1 $2 "Multiple runout sensors (x5) | Distinct runout states" "$3"
#
# Test MINIRAMBO with PWM_MOTOR_CURRENT and many features
#
restore_configs
opt_set MOTHERBOARD BOARD_MEGACONTROLLER
opt_set LCD_LANGUAGE de
opt_enable EEPROM_SETTINGS EEPROM_CHITCHAT \
MINIPANEL SDSUPPORT PCA9632 LCD_INFO_MENU SOUND_MENU_ITEM GCODE_REPEAT_MARKERS \
AUTO_BED_LEVELING_BILINEAR PROBE_MANUALLY LCD_BED_LEVELING G26_MESH_VALIDATION MESH_EDIT_MENU \
LIN_ADVANCE EXTRA_LIN_ADVANCE_K \
INCH_MODE_SUPPORT TEMPERATURE_UNITS_SUPPORT EXPERIMENTAL_I2CBUS M100_FREE_MEMORY_WATCHER \
NOZZLE_PARK_FEATURE NOZZLE_CLEAN_FEATURE \
ADVANCED_PAUSE_FEATURE PARK_HEAD_ON_PAUSE ADVANCED_PAUSE_CONTINUOUS_PURGE FILAMENT_LOAD_UNLOAD_GCODES \
PRINTCOUNTER SERVICE_NAME_1 SERVICE_INTERVAL_1 M114_DETAIL \
USE_CONTROLLER_FAN CONTROLLER_FAN_EDITABLE
opt_set CONTROLLERFAN_SPEED_IDLE 128
opt_add M100_FREE_MEMORY_DUMPER
opt_add M100_FREE_MEMORY_CORRUPTOR
opt_set PWM_MOTOR_CURRENT "{ 1300, 1300, 1250 }"
opt_set I2C_SLAVE_ADDRESS 63
exec_test $1 $2 "MEGACONTROLLER | Minipanel | M100 | PWM_MOTOR_CURRENT | PRINTCOUNTER | Advanced Pause ..." "$3"
#
# Mixing Extruder with 5 steppers, Greek
@ -150,31 +114,6 @@ exec_test $1 $2 "Azteeg X3 | Mixing Extruder (x5) | Gradient Mix | Greek" "$3"
#opt_enable COREXY
#exec_test $1 $2 "Stuff" "$3"
#
# Test many less common options
#
restore_configs
opt_set MOTHERBOARD BOARD_MIGHTYBOARD_REVE
opt_set TEMP_SENSOR_0 -2
opt_set DIGIPOT_I2C_NUM_CHANNELS 5
opt_set LCD_LANGUAGE it
opt_set MIXING_STEPPERS 2
opt_set SERVO_DELAY "{ 300, 300, 300 }"
opt_enable COREYX USE_XMAX_PLUG MIXING_EXTRUDER GRADIENT_MIX \
BABYSTEPPING BABYSTEP_DISPLAY_TOTAL FILAMENT_LCD_DISPLAY \
REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER MENU_ADDAUTOSTART SDSUPPORT SDCARD_SORT_ALPHA \
ENDSTOP_NOISE_THRESHOLD FAN_SOFT_PWM \
FIX_MOUNTED_PROBE AUTO_BED_LEVELING_LINEAR DEBUG_LEVELING_FEATURE FILAMENT_WIDTH_SENSOR PROBE_OFFSET_WIZARD \
Z_SAFE_HOMING SHOW_TEMP_ADC_VALUES HOME_Y_BEFORE_X EMERGENCY_PARSER \
SD_ABORT_ON_ENDSTOP_HIT HOST_ACTION_COMMANDS HOST_PROMPT_SUPPORT ADVANCED_OK M114_DETAIL \
VOLUMETRIC_DEFAULT_ON NO_WORKSPACE_OFFSETS EXTRA_FAN_SPEED FWRETRACT \
USE_CONTROLLER_FAN CONTROLLER_FAN_EDITABLE CONTROLLER_FAN_USE_Z_ONLY
opt_set FAN_MIN_PWM 50
opt_set FAN_KICKSTART_TIME 100
opt_set XY_FREQUENCY_LIMIT 15
opt_add FILWIDTH_PIN 5
exec_test $1 $2 "Mightyboard Rev. E | CoreXY, Gradient Mix | Endstop Int. | Home Y > X | FW Retract ..." "$3"
######## Other Standard LCD/Panels ##############
#
# ULTRA_LCD
@ -277,71 +216,15 @@ exec_test $1 $2 "Formbot/T_Rex_3 example configuration." "$3"
#
# BQ Hephestos 2
#restore_configs
#use_example_configs Hephestos_2
#use_example_configs BQ/Hephestos_2
#exec_test $1 $2 "Stuff" "$3"
#
# Delta Config (generic) + UBL + ALLEN_KEY + EEPROM_SETTINGS + OLED_PANEL_TINYBOY2
#
use_example_configs delta/generic
opt_enable RESTORE_LEVELING_AFTER_G28 EEPROM_SETTINGS EEPROM_CHITCHAT \
Z_PROBE_ALLEN_KEY AUTO_BED_LEVELING_UBL \
OLED_PANEL_TINYBOY2 MESH_EDIT_GFX_OVERLAY DELTA_CALIBRATION_MENU
opt_set LCD_LANGUAGE ko_KR
opt_set X_DRIVER_TYPE L6470
opt_set Y_DRIVER_TYPE L6470
opt_set Z_DRIVER_TYPE L6470
opt_add L6470_CHAIN_SCK_PIN 53
opt_add L6470_CHAIN_MISO_PIN 49
opt_add L6470_CHAIN_MOSI_PIN 40
opt_add L6470_CHAIN_SS_PIN 42
opt_add "ENABLE_RESET_L64XX_CHIPS(V) NOOP"
exec_test $1 $2 "DELTA, RAMPS, L6470, UBL, Allen Key, EEPROM, OLED_PANEL_TINYBOY2..." "$3"
#
# Delta Config (FLSUN AC because it's complex)
#
use_example_configs delta/FLSUN/auto_calibrate
exec_test $1 $2 "RAMPS 1.3 | DELTA | FLSUN AC Config" "$3"
#
# Makibox Config need to check board type for Teensy++ 2.0
#
#use_example_configs makibox
#exec_test $1 $2 "Stuff" "$3"
#
# Test mixed TMC config
#
restore_configs
opt_set LCD_LANGUAGE vi
opt_set X_DRIVER_TYPE TMC2160
opt_set Y_DRIVER_TYPE TMC5160
opt_set Z_DRIVER_TYPE TMC2208_STANDALONE
opt_set E0_DRIVER_TYPE TMC2130
opt_set X_MIN_ENDSTOP_INVERTING true
opt_set Y_MIN_ENDSTOP_INVERTING true
opt_enable REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER \
MARLIN_BRICKOUT MARLIN_INVADERS MARLIN_SNAKE \
MONITOR_DRIVER_STATUS STEALTHCHOP_XY STEALTHCHOP_Z STEALTHCHOP_E HYBRID_THRESHOLD \
USE_ZMIN_PLUG SENSORLESS_HOMING TMC_DEBUG M114_DETAIL
exec_test $1 $2 "RAMPS | Mixed TMC | Sensorless | RRDFGSC | Games" "$3"
#
# SCARA with Mixed TMC
#
use_example_configs SCARA/Morgan
opt_set LCD_LANGUAGE es
opt_enable USE_ZMIN_PLUG FIX_MOUNTED_PROBE AUTO_BED_LEVELING_BILINEAR PAUSE_BEFORE_DEPLOY_STOW \
MKS_12864OLED EEPROM_SETTINGS EEPROM_CHITCHAT M114_DETAIL Z_SAFE_HOMING \
STEALTHCHOP_XY STEALTHCHOP_Z STEALTHCHOP_E HYBRID_THRESHOLD SENSORLESS_HOMING SQUARE_WAVE_STEPPING
opt_set X_MAX_ENDSTOP_INVERTING false
opt_set X_DRIVER_TYPE TMC2209
opt_set Y_DRIVER_TYPE TMC2130
opt_set Z_DRIVER_TYPE TMC2130_STANDALONE
opt_set E0_DRIVER_TYPE TMC2660
exec_test $1 $2 "RAMPS | SCARA | Mixed TMC | EEPROM" "$3"
#
# tvrrug Config need to check board type for sanguino atmega644p
#

View File

@ -10,5 +10,13 @@ set -e
use_example_configs Mks/Robin
exec_test $1 $2 "MKS Robin config (FSMC Color UI)" "$3"
#
# MKS Robin LVGL FSMC
#
use_example_configs Mks/Robin
opt_disable TFT_CLASSIC_UI TFT_COLOR_UI TOUCH_SCREEN TFT_RES_320x240
opt_enable TFT_LVGL_UI TFT_RES_480x320
exec_test $1 $2 "MKS Robin nano v1.2 LVGL FSMC" "$3"
# cleanup
restore_configs

View File

@ -24,15 +24,6 @@ opt_disable TFT_INTERFACE_FSMC
opt_enable TFT_INTERFACE_SPI
exec_test $1 $2 "MKS Robin v2 nano Emulated DOGM SPI" "$3"
#
# MKS Robin nano v1.2 LVGL FSMC
#
use_example_configs Mks/Robin
opt_set MOTHERBOARD BOARD_MKS_ROBIN_NANO
opt_disable TFT_CLASSIC_UI TFT_COLOR_UI TOUCH_SCREEN TFT_RES_320x240
opt_enable TFT_LVGL_UI TFT_RES_480x320
exec_test $1 $2 "MKS Robin nano v1.2 LVGL FSMC" "$3"
#
# MKS Robin v2 nano LVGL SPI
# (Robin v2 nano has no FSMC interface)

View File

@ -81,5 +81,51 @@ opt_set Z_DRIVER_TYPE TMC2130
opt_set E0_DRIVER_TYPE TMC2130
exec_test $1 $2 "Einsy RAMBo with TMC2130" "$3"
#
# Test MINIRAMBO with PWM_MOTOR_CURRENT and many features
#
restore_configs
opt_set MOTHERBOARD BOARD_MINIRAMBO
opt_enable EEPROM_SETTINGS EEPROM_CHITCHAT REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER \
SDSUPPORT PCA9632 SOUND_MENU_ITEM GCODE_REPEAT_MARKERS \
AUTO_BED_LEVELING_BILINEAR PROBE_MANUALLY LCD_BED_LEVELING G26_MESH_VALIDATION MESH_EDIT_MENU \
LIN_ADVANCE EXTRA_LIN_ADVANCE_K \
INCH_MODE_SUPPORT TEMPERATURE_UNITS_SUPPORT EXPERIMENTAL_I2CBUS M100_FREE_MEMORY_WATCHER \
NOZZLE_PARK_FEATURE NOZZLE_CLEAN_FEATURE \
ADVANCED_PAUSE_FEATURE PARK_HEAD_ON_PAUSE ADVANCED_PAUSE_CONTINUOUS_PURGE FILAMENT_LOAD_UNLOAD_GCODES \
PRINTCOUNTER SERVICE_NAME_1 SERVICE_INTERVAL_1 M114_DETAIL
opt_set CONTROLLERFAN_SPEED_IDLE 128
opt_add M100_FREE_MEMORY_DUMPER
opt_add M100_FREE_MEMORY_CORRUPTOR
opt_set PWM_MOTOR_CURRENT "{ 1300, 1300, 1250 }"
opt_set I2C_SLAVE_ADDRESS 63
exec_test $1 $2 "MINIRAMBO | RRDGFSC | M100 | PWM_MOTOR_CURRENT | PRINTCOUNTER | Advanced Pause ..." "$3"
#
# Test many less common options
#
restore_configs
opt_set MOTHERBOARD BOARD_RAMBO
opt_set TEMP_SENSOR_0 -2
opt_set DIGIPOT_I2C_NUM_CHANNELS 5
opt_set LCD_LANGUAGE it
opt_set MIXING_STEPPERS 2
opt_set SERVO_DELAY "{ 300, 300, 300 }"
opt_enable COREYX USE_XMAX_PLUG MIXING_EXTRUDER GRADIENT_MIX \
BABYSTEPPING BABYSTEP_DISPLAY_TOTAL FILAMENT_LCD_DISPLAY \
REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER MENU_ADDAUTOSTART SDSUPPORT SDCARD_SORT_ALPHA \
ENDSTOP_NOISE_THRESHOLD FAN_SOFT_PWM \
FIX_MOUNTED_PROBE AUTO_BED_LEVELING_LINEAR DEBUG_LEVELING_FEATURE FILAMENT_WIDTH_SENSOR PROBE_OFFSET_WIZARD \
Z_SAFE_HOMING SHOW_TEMP_ADC_VALUES HOME_Y_BEFORE_X EMERGENCY_PARSER \
SD_ABORT_ON_ENDSTOP_HIT HOST_ACTION_COMMANDS HOST_PROMPT_SUPPORT ADVANCED_OK M114_DETAIL \
VOLUMETRIC_DEFAULT_ON NO_WORKSPACE_OFFSETS EXTRA_FAN_SPEED FWRETRACT \
USE_CONTROLLER_FAN CONTROLLER_FAN_EDITABLE CONTROLLER_FAN_USE_Z_ONLY
opt_set CONTROLLER_FAN_PIN X_MAX_PIN
opt_set FAN_MIN_PWM 50
opt_set FAN_KICKSTART_TIME 100
opt_set XY_FREQUENCY_LIMIT 15
opt_add FILWIDTH_PIN 5
exec_test $1 $2 "Rambo | CoreXY, Gradient Mix | Endstop Int. | Home Y > X | FW Retract ..." "$3"
# clean up
restore_configs

View File

@ -11,7 +11,11 @@ set -e
#
restore_configs
opt_set MOTHERBOARD BOARD_SANGUINOLOLU_12
exec_test $1 $2 "Default Configuration" "$3"
opt_set LCD_LANGUAGE de
opt_enable MINIPANEL USE_CONTROLLER_FAN CONTROLLER_FAN_EDITABLE
opt_set CONTROLLER_FAN_PIN 27
exec_test $1 $2 "Default Configuration | MINIPANAL | CONTROLLER_FAN" "$3"
# clean up
restore_configs

0
get_test_targets.py Normal file → Executable file
View File