Added PID autotune. (experimental)
M303 Starts autotune. Wait till the Kp Ki and Kd constants are printed. Put these values in Configuration.h
This commit is contained in:
Erik van der Zalm
parent
116dc86b8a
commit
c077316b2b
@ -109,6 +109,7 @@
|
||||
// M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily).
|
||||
// M502 - reverts to the default "factory settings". You still need to store them in EEPROM afterwards if you want to.
|
||||
// M503 - print the current settings (from memory not from eeprom)
|
||||
// M303 - PID relay autotune S<temperature> sets the target temperature. (default target temperature = 150C)
|
||||
|
||||
//Stepper Movement Variables
|
||||
|
||||
@ -1197,6 +1198,13 @@ void process_commands()
|
||||
allow_cold_extrudes(true);
|
||||
}
|
||||
break;
|
||||
case 303: // M303 PID autotune
|
||||
{
|
||||
float temp = 150.0;
|
||||
if (code_seen('S')) temp=code_value();
|
||||
PID_autotune(temp);
|
||||
}
|
||||
break;
|
||||
case 400: // finish all moves
|
||||
{
|
||||
st_synchronize();
|
||||
|
||||
@ -734,7 +734,7 @@
|
||||
#define encrot2 3
|
||||
#define encrot3 1
|
||||
|
||||
|
||||
#define SDCARDDETECT -1
|
||||
//bits in the shift register that carry the buttons for:
|
||||
// left up center down right red
|
||||
#define BL_LE 7
|
||||
|
||||
@ -62,7 +62,7 @@ int current_raw_bed = 0;
|
||||
//===========================================================================
|
||||
//=============================private variables============================
|
||||
//===========================================================================
|
||||
static bool temp_meas_ready = false;
|
||||
static volatile bool temp_meas_ready = false;
|
||||
|
||||
static unsigned long previous_millis_bed_heater;
|
||||
//static unsigned long previous_millis_heater;
|
||||
@ -132,7 +132,94 @@ static unsigned long previous_millis_bed_heater;
|
||||
//===========================================================================
|
||||
//============================= functions ============================
|
||||
//===========================================================================
|
||||
|
||||
void PID_autotune(float temp)
|
||||
{
|
||||
float input;
|
||||
int cycles=0;
|
||||
bool heating = true;
|
||||
soft_pwm[0] = 255>>1;
|
||||
|
||||
unsigned long temp_millis = millis();
|
||||
unsigned long t1=temp_millis;
|
||||
unsigned long t2=temp_millis;
|
||||
long t_high;
|
||||
long t_low;
|
||||
|
||||
long bias=127;
|
||||
long d = 127;
|
||||
float Ku, Tu;
|
||||
float Kp, Ki, Kd;
|
||||
float max, min;
|
||||
|
||||
SERIAL_ECHOLN("PID Autotune start");
|
||||
|
||||
for(;;) {
|
||||
|
||||
if(temp_meas_ready == true) { // temp sample ready
|
||||
CRITICAL_SECTION_START;
|
||||
temp_meas_ready = false;
|
||||
CRITICAL_SECTION_END;
|
||||
input = analog2temp(current_raw[0], 0);
|
||||
|
||||
max=max(max,input);
|
||||
min=min(min,input);
|
||||
if(heating == true && input > temp) {
|
||||
if(millis() - t2 > 5000) {
|
||||
heating=false;
|
||||
soft_pwm[0] = (bias - d) >> 1;
|
||||
t1=millis();
|
||||
t_high=t1 - t2;
|
||||
max=temp;
|
||||
}
|
||||
}
|
||||
if(heating == false && input < temp) {
|
||||
if(millis() - t1 > 5000) {
|
||||
heating=true;
|
||||
t2=millis();
|
||||
t_low=t2 - t1;
|
||||
if(cycles > 0) {
|
||||
bias += (d*(t_high - t_low))/(t_low + t_high);
|
||||
bias = constrain(bias, 20 ,235);
|
||||
if(bias > 127) d = 254 - bias;
|
||||
else d = bias;
|
||||
|
||||
SERIAL_PROTOCOLPGM(" bias: "); SERIAL_PROTOCOL(bias);
|
||||
SERIAL_PROTOCOLPGM(" d: "); SERIAL_PROTOCOL(d);
|
||||
SERIAL_PROTOCOLPGM(" min: "); SERIAL_PROTOCOL(min);
|
||||
SERIAL_PROTOCOLPGM(" max: "); SERIAL_PROTOCOLLN(max);
|
||||
if(cycles > 2) {
|
||||
Ku = (4.0*d)/(3.14159*(max-min)/2.0);
|
||||
Tu = ((float)(t_low + t_high)/1000.0);
|
||||
Kp = 0.6*Ku;
|
||||
Ki = 2*Kp/Tu;
|
||||
Kd = Kp*Tu/8;
|
||||
SERIAL_PROTOCOLPGM(" Kp: "); SERIAL_PROTOCOLLN(Kp);
|
||||
SERIAL_PROTOCOLPGM(" Ki: "); SERIAL_PROTOCOLLN(Ki);
|
||||
SERIAL_PROTOCOLPGM(" Kd: "); SERIAL_PROTOCOLLN(Kd);
|
||||
}
|
||||
}
|
||||
soft_pwm[0] = (bias + d) >> 1;
|
||||
cycles++;
|
||||
min=temp;
|
||||
}
|
||||
}
|
||||
}
|
||||
if(input > (temp + 20)) {
|
||||
SERIAL_PROTOCOLLNPGM("PID Autotune failed !!!, Temperature to high");
|
||||
return;
|
||||
}
|
||||
if(millis() - temp_millis > 2000) {
|
||||
temp_millis = millis();
|
||||
SERIAL_PROTOCOLPGM("ok T:");
|
||||
SERIAL_PROTOCOL(degHotend(0));
|
||||
SERIAL_PROTOCOLPGM(" @:");
|
||||
SERIAL_PROTOCOLLN(getHeaterPower(0));
|
||||
}
|
||||
LCD_STATUS;
|
||||
}
|
||||
}
|
||||
|
||||
void updatePID()
|
||||
{
|
||||
#ifdef PIDTEMP
|
||||
|
||||
@ -1,162 +1,165 @@
|
||||
/*
|
||||
temperature.h - temperature controller
|
||||
Part of Marlin
|
||||
|
||||
Copyright (c) 2011 Erik van der Zalm
|
||||
|
||||
Grbl is free software: you can redistribute it and/or modify
|
||||
it under the terms of the GNU General Public License as published by
|
||||
the Free Software Foundation, either version 3 of the License, or
|
||||
(at your option) any later version.
|
||||
|
||||
Grbl is distributed in the hope that it will be useful,
|
||||
but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||||
GNU General Public License for more details.
|
||||
|
||||
You should have received a copy of the GNU General Public License
|
||||
along with Grbl. If not, see <http://www.gnu.org/licenses/>.
|
||||
*/
|
||||
|
||||
#ifndef temperature_h
|
||||
#define temperature_h
|
||||
|
||||
#include "Marlin.h"
|
||||
#include "planner.h"
|
||||
#ifdef PID_ADD_EXTRUSION_RATE
|
||||
#include "stepper.h"
|
||||
#endif
|
||||
|
||||
// public functions
|
||||
void tp_init(); //initialise the heating
|
||||
void manage_heater(); //it is critical that this is called periodically.
|
||||
|
||||
//low leven conversion routines
|
||||
// do not use this routines and variables outsie of temperature.cpp
|
||||
int temp2analog(int celsius, uint8_t e);
|
||||
int temp2analogBed(int celsius);
|
||||
float analog2temp(int raw, uint8_t e);
|
||||
float analog2tempBed(int raw);
|
||||
extern int target_raw[EXTRUDERS];
|
||||
extern int heatingtarget_raw[EXTRUDERS];
|
||||
extern int current_raw[EXTRUDERS];
|
||||
extern int target_raw_bed;
|
||||
extern int current_raw_bed;
|
||||
#ifdef BED_LIMIT_SWITCHING
|
||||
extern int target_bed_low_temp ;
|
||||
extern int target_bed_high_temp ;
|
||||
#endif
|
||||
extern float Kp,Ki,Kd,Kc;
|
||||
|
||||
#ifdef PIDTEMP
|
||||
extern float pid_setpoint[EXTRUDERS];
|
||||
#endif
|
||||
|
||||
// #ifdef WATCHPERIOD
|
||||
extern int watch_raw[EXTRUDERS] ;
|
||||
// extern unsigned long watchmillis;
|
||||
// #endif
|
||||
|
||||
|
||||
//high level conversion routines, for use outside of temperature.cpp
|
||||
//inline so that there is no performance decrease.
|
||||
//deg=degreeCelsius
|
||||
|
||||
FORCE_INLINE float degHotend(uint8_t extruder) {
|
||||
return analog2temp(current_raw[extruder], extruder);
|
||||
};
|
||||
|
||||
FORCE_INLINE float degBed() {
|
||||
return analog2tempBed(current_raw_bed);
|
||||
};
|
||||
|
||||
FORCE_INLINE float degTargetHotend(uint8_t extruder) {
|
||||
return analog2temp(target_raw[extruder], extruder);
|
||||
};
|
||||
|
||||
FORCE_INLINE float degTargetBed() {
|
||||
return analog2tempBed(target_raw_bed);
|
||||
};
|
||||
|
||||
FORCE_INLINE void setTargetHotend(const float &celsius, uint8_t extruder) {
|
||||
target_raw[extruder] = temp2analog(celsius, extruder);
|
||||
#ifdef PIDTEMP
|
||||
pid_setpoint[extruder] = celsius;
|
||||
#endif //PIDTEMP
|
||||
};
|
||||
|
||||
FORCE_INLINE void setTargetBed(const float &celsius) {
|
||||
|
||||
target_raw_bed = temp2analogBed(celsius);
|
||||
#ifdef BED_LIMIT_SWITCHING
|
||||
if(celsius>BED_HYSTERESIS)
|
||||
{
|
||||
target_bed_low_temp= temp2analogBed(celsius-BED_HYSTERESIS);
|
||||
target_bed_high_temp= temp2analogBed(celsius+BED_HYSTERESIS);
|
||||
}
|
||||
else
|
||||
{
|
||||
target_bed_low_temp=0;
|
||||
target_bed_high_temp=0;
|
||||
}
|
||||
#endif
|
||||
};
|
||||
|
||||
FORCE_INLINE bool isHeatingHotend(uint8_t extruder){
|
||||
return target_raw[extruder] > current_raw[extruder];
|
||||
};
|
||||
|
||||
FORCE_INLINE bool isHeatingBed() {
|
||||
return target_raw_bed > current_raw_bed;
|
||||
};
|
||||
|
||||
FORCE_INLINE bool isCoolingHotend(uint8_t extruder) {
|
||||
return target_raw[extruder] < current_raw[extruder];
|
||||
};
|
||||
|
||||
FORCE_INLINE bool isCoolingBed() {
|
||||
return target_raw_bed < current_raw_bed;
|
||||
};
|
||||
|
||||
#define degHotend0() degHotend(0)
|
||||
#define degTargetHotend0() degTargetHotend(0)
|
||||
#define setTargetHotend0(_celsius) setTargetHotend((_celsius), 0)
|
||||
#define isHeatingHotend0() isHeatingHotend(0)
|
||||
#define isCoolingHotend0() isCoolingHotend(0)
|
||||
#if EXTRUDERS > 1
|
||||
#define degHotend1() degHotend(1)
|
||||
#define degTargetHotend1() degTargetHotend(1)
|
||||
#define setTargetHotend1(_celsius) setTargetHotend((_celsius), 1)
|
||||
#define isHeatingHotend1() isHeatingHotend(1)
|
||||
#define isCoolingHotend1() isCoolingHotend(1)
|
||||
#endif
|
||||
#if EXTRUDERS > 2
|
||||
#define degHotend2() degHotend(2)
|
||||
#define degTargetHotend2() degTargetHotend(2)
|
||||
#define setTargetHotend2(_celsius) setTargetHotend((_celsius), 2)
|
||||
#define isHeatingHotend2() isHeatingHotend(2)
|
||||
#define isCoolingHotend2() isCoolingHotend(2)
|
||||
#endif
|
||||
#if EXTRUDERS > 3
|
||||
#error Invalid number of extruders
|
||||
#endif
|
||||
|
||||
|
||||
|
||||
int getHeaterPower(int heater);
|
||||
void disable_heater();
|
||||
void setWatch();
|
||||
void updatePID();
|
||||
|
||||
FORCE_INLINE void autotempShutdown(){
|
||||
#ifdef AUTOTEMP
|
||||
if(autotemp_enabled)
|
||||
{
|
||||
autotemp_enabled=false;
|
||||
if(degTargetHotend(ACTIVE_EXTRUDER)>autotemp_min)
|
||||
setTargetHotend(0,ACTIVE_EXTRUDER);
|
||||
}
|
||||
#endif
|
||||
}
|
||||
#endif
|
||||
/*
|
||||
temperature.h - temperature controller
|
||||
Part of Marlin
|
||||
|
||||
Copyright (c) 2011 Erik van der Zalm
|
||||
|
||||
Grbl is free software: you can redistribute it and/or modify
|
||||
it under the terms of the GNU General Public License as published by
|
||||
the Free Software Foundation, either version 3 of the License, or
|
||||
(at your option) any later version.
|
||||
|
||||
Grbl is distributed in the hope that it will be useful,
|
||||
but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||||
GNU General Public License for more details.
|
||||
|
||||
You should have received a copy of the GNU General Public License
|
||||
along with Grbl. If not, see <http://www.gnu.org/licenses/>.
|
||||
*/
|
||||
|
||||
#ifndef temperature_h
|
||||
#define temperature_h
|
||||
|
||||
#include "Marlin.h"
|
||||
#include "planner.h"
|
||||
#ifdef PID_ADD_EXTRUSION_RATE
|
||||
#include "stepper.h"
|
||||
#endif
|
||||
|
||||
// public functions
|
||||
void tp_init(); //initialise the heating
|
||||
void manage_heater(); //it is critical that this is called periodically.
|
||||
|
||||
//low leven conversion routines
|
||||
// do not use this routines and variables outsie of temperature.cpp
|
||||
int temp2analog(int celsius, uint8_t e);
|
||||
int temp2analogBed(int celsius);
|
||||
float analog2temp(int raw, uint8_t e);
|
||||
float analog2tempBed(int raw);
|
||||
extern int target_raw[EXTRUDERS];
|
||||
extern int heatingtarget_raw[EXTRUDERS];
|
||||
extern int current_raw[EXTRUDERS];
|
||||
extern int target_raw_bed;
|
||||
extern int current_raw_bed;
|
||||
#ifdef BED_LIMIT_SWITCHING
|
||||
extern int target_bed_low_temp ;
|
||||
extern int target_bed_high_temp ;
|
||||
#endif
|
||||
extern float Kp,Ki,Kd,Kc;
|
||||
|
||||
#ifdef PIDTEMP
|
||||
extern float pid_setpoint[EXTRUDERS];
|
||||
#endif
|
||||
|
||||
// #ifdef WATCHPERIOD
|
||||
extern int watch_raw[EXTRUDERS] ;
|
||||
// extern unsigned long watchmillis;
|
||||
// #endif
|
||||
|
||||
|
||||
//high level conversion routines, for use outside of temperature.cpp
|
||||
//inline so that there is no performance decrease.
|
||||
//deg=degreeCelsius
|
||||
|
||||
FORCE_INLINE float degHotend(uint8_t extruder) {
|
||||
return analog2temp(current_raw[extruder], extruder);
|
||||
};
|
||||
|
||||
FORCE_INLINE float degBed() {
|
||||
return analog2tempBed(current_raw_bed);
|
||||
};
|
||||
|
||||
FORCE_INLINE float degTargetHotend(uint8_t extruder) {
|
||||
return analog2temp(target_raw[extruder], extruder);
|
||||
};
|
||||
|
||||
FORCE_INLINE float degTargetBed() {
|
||||
return analog2tempBed(target_raw_bed);
|
||||
};
|
||||
|
||||
FORCE_INLINE void setTargetHotend(const float &celsius, uint8_t extruder) {
|
||||
target_raw[extruder] = temp2analog(celsius, extruder);
|
||||
#ifdef PIDTEMP
|
||||
pid_setpoint[extruder] = celsius;
|
||||
#endif //PIDTEMP
|
||||
};
|
||||
|
||||
FORCE_INLINE void setTargetBed(const float &celsius) {
|
||||
|
||||
target_raw_bed = temp2analogBed(celsius);
|
||||
#ifdef BED_LIMIT_SWITCHING
|
||||
if(celsius>BED_HYSTERESIS)
|
||||
{
|
||||
target_bed_low_temp= temp2analogBed(celsius-BED_HYSTERESIS);
|
||||
target_bed_high_temp= temp2analogBed(celsius+BED_HYSTERESIS);
|
||||
}
|
||||
else
|
||||
{
|
||||
target_bed_low_temp=0;
|
||||
target_bed_high_temp=0;
|
||||
}
|
||||
#endif
|
||||
};
|
||||
|
||||
FORCE_INLINE bool isHeatingHotend(uint8_t extruder){
|
||||
return target_raw[extruder] > current_raw[extruder];
|
||||
};
|
||||
|
||||
FORCE_INLINE bool isHeatingBed() {
|
||||
return target_raw_bed > current_raw_bed;
|
||||
};
|
||||
|
||||
FORCE_INLINE bool isCoolingHotend(uint8_t extruder) {
|
||||
return target_raw[extruder] < current_raw[extruder];
|
||||
};
|
||||
|
||||
FORCE_INLINE bool isCoolingBed() {
|
||||
return target_raw_bed < current_raw_bed;
|
||||
};
|
||||
|
||||
#define degHotend0() degHotend(0)
|
||||
#define degTargetHotend0() degTargetHotend(0)
|
||||
#define setTargetHotend0(_celsius) setTargetHotend((_celsius), 0)
|
||||
#define isHeatingHotend0() isHeatingHotend(0)
|
||||
#define isCoolingHotend0() isCoolingHotend(0)
|
||||
#if EXTRUDERS > 1
|
||||
#define degHotend1() degHotend(1)
|
||||
#define degTargetHotend1() degTargetHotend(1)
|
||||
#define setTargetHotend1(_celsius) setTargetHotend((_celsius), 1)
|
||||
#define isHeatingHotend1() isHeatingHotend(1)
|
||||
#define isCoolingHotend1() isCoolingHotend(1)
|
||||
#endif
|
||||
#if EXTRUDERS > 2
|
||||
#define degHotend2() degHotend(2)
|
||||
#define degTargetHotend2() degTargetHotend(2)
|
||||
#define setTargetHotend2(_celsius) setTargetHotend((_celsius), 2)
|
||||
#define isHeatingHotend2() isHeatingHotend(2)
|
||||
#define isCoolingHotend2() isCoolingHotend(2)
|
||||
#endif
|
||||
#if EXTRUDERS > 3
|
||||
#error Invalid number of extruders
|
||||
#endif
|
||||
|
||||
|
||||
|
||||
int getHeaterPower(int heater);
|
||||
void disable_heater();
|
||||
void setWatch();
|
||||
void updatePID();
|
||||
|
||||
FORCE_INLINE void autotempShutdown(){
|
||||
#ifdef AUTOTEMP
|
||||
if(autotemp_enabled)
|
||||
{
|
||||
autotemp_enabled=false;
|
||||
if(degTargetHotend(ACTIVE_EXTRUDER)>autotemp_min)
|
||||
setTargetHotend(0,ACTIVE_EXTRUDER);
|
||||
}
|
||||
#endif
|
||||
}
|
||||
|
||||
void PID_autotune(float temp);
|
||||
|
||||
#endif
|
||||
|
||||
|
||||
@ -315,19 +315,18 @@ void MainMenu::showStatus()
|
||||
static int olddegHotEnd0=-1;
|
||||
static int oldtargetHotEnd0=-1;
|
||||
//force_lcd_update=true;
|
||||
if(force_lcd_update||feedmultiplychanged) //initial display of content
|
||||
if(force_lcd_update) //initial display of content
|
||||
{
|
||||
feedmultiplychanged=false;
|
||||
encoderpos=feedmultiply;
|
||||
clear();
|
||||
lcd.setCursor(0,0);lcdprintPGM("\002123/567\001 ");
|
||||
lcd.setCursor(0,0);lcdprintPGM("\002---/---\001 ");
|
||||
#if defined BED_USES_THERMISTOR || defined BED_USES_AD595
|
||||
lcd.setCursor(10,0);lcdprintPGM("B123/567\001 ");
|
||||
lcd.setCursor(10,0);lcdprintPGM("B---/---\001 ");
|
||||
#endif
|
||||
}
|
||||
|
||||
int tHotEnd0=intround(degHotend0());
|
||||
if((abs(tHotEnd0-olddegHotEnd0)>1)||force_lcd_update) //>1 because otherwise the lcd is refreshed to often.
|
||||
if((tHotEnd0!=olddegHotEnd0)||force_lcd_update)
|
||||
{
|
||||
lcd.setCursor(1,0);
|
||||
lcd.print(ftostr3(tHotEnd0));
|
||||
@ -379,8 +378,15 @@ void MainMenu::showStatus()
|
||||
lcdprintPGM("Z:");lcd.print(ftostr52(current_position[2]));
|
||||
oldzpos=currentz;
|
||||
}
|
||||
|
||||
static int oldfeedmultiply=0;
|
||||
int curfeedmultiply=feedmultiply;
|
||||
|
||||
if(feedmultiplychanged == true) {
|
||||
feedmultiplychanged == false;
|
||||
encoderpos = curfeedmultiply;
|
||||
}
|
||||
|
||||
if(encoderpos!=curfeedmultiply||force_lcd_update)
|
||||
{
|
||||
curfeedmultiply=encoderpos;
|
||||
@ -391,12 +397,14 @@ void MainMenu::showStatus()
|
||||
feedmultiply=curfeedmultiply;
|
||||
encoderpos=curfeedmultiply;
|
||||
}
|
||||
|
||||
if((curfeedmultiply!=oldfeedmultiply)||force_lcd_update)
|
||||
{
|
||||
oldfeedmultiply=curfeedmultiply;
|
||||
lcd.setCursor(0,2);
|
||||
lcd.print(itostr3(curfeedmultiply));lcdprintPGM("% ");
|
||||
}
|
||||
|
||||
if(messagetext[0]!='\0')
|
||||
{
|
||||
lcd.setCursor(0,LCD_HEIGHT-1);
|
||||
@ -404,7 +412,6 @@ void MainMenu::showStatus()
|
||||
uint8_t n=strlen(messagetext);
|
||||
for(int8_t i=0;i<LCD_WIDTH-n;i++)
|
||||
lcd.print(" ");
|
||||
|
||||
messagetext[0]='\0';
|
||||
}
|
||||
|
||||
|
||||
Loading…
Reference in New Issue
Block a user