Apply indentation to gcode_M303, PID_autotune
This commit is contained in:
Scott Lahteine
parent
ba66336503
commit
a26d70e932
@ -5559,25 +5559,25 @@ inline void gcode_M226() {
|
||||
* U<bool> with a non-zero value will apply the result to current settings
|
||||
*/
|
||||
inline void gcode_M303() {
|
||||
#if ENABLED(PIDTEMP)
|
||||
int e = code_seen('E') ? code_value_short() : 0;
|
||||
int c = code_seen('C') ? code_value_short() : 5;
|
||||
bool u = code_seen('U') && code_value_short() != 0;
|
||||
#if ENABLED(PIDTEMP)
|
||||
int e = code_seen('E') ? code_value_short() : 0;
|
||||
int c = code_seen('C') ? code_value_short() : 5;
|
||||
bool u = code_seen('U') && code_value_short() != 0;
|
||||
|
||||
float temp = code_seen('S') ? code_value() : (e < 0 ? 70.0 : 150.0);
|
||||
float temp = code_seen('S') ? code_value() : (e < 0 ? 70.0 : 150.0);
|
||||
|
||||
if (e >= 0 && e < EXTRUDERS)
|
||||
target_extruder = e;
|
||||
if (e >= 0 && e < EXTRUDERS)
|
||||
target_extruder = e;
|
||||
|
||||
KEEPALIVE_STATE(NOT_BUSY); // don't send "busy: processing" messages during autotune output
|
||||
KEEPALIVE_STATE(NOT_BUSY); // don't send "busy: processing" messages during autotune output
|
||||
|
||||
PID_autotune(temp, e, c, u);
|
||||
PID_autotune(temp, e, c, u);
|
||||
|
||||
KEEPALIVE_STATE(IN_HANDLER);
|
||||
#else
|
||||
SERIAL_ERROR_START;
|
||||
SERIAL_ERRORLNPGM(MSG_ERR_M303_DISABLED);
|
||||
#endif
|
||||
KEEPALIVE_STATE(IN_HANDLER);
|
||||
#else
|
||||
SERIAL_ERROR_START;
|
||||
SERIAL_ERRORLNPGM(MSG_ERR_M303_DISABLED);
|
||||
#endif
|
||||
}
|
||||
|
||||
#if ENABLED(SCARA)
|
||||
|
||||
@ -223,176 +223,176 @@ static void updateTemperaturesFromRawValues();
|
||||
|
||||
#if ENABLED(PIDTEMP)
|
||||
|
||||
void PID_autotune(float temp, int extruder, int ncycles, bool set_result/*=false*/) {
|
||||
float input = 0.0;
|
||||
int cycles = 0;
|
||||
bool heating = true;
|
||||
void PID_autotune(float temp, int extruder, int ncycles, bool set_result/*=false*/) {
|
||||
float input = 0.0;
|
||||
int cycles = 0;
|
||||
bool heating = true;
|
||||
|
||||
millis_t temp_ms = millis(), t1 = temp_ms, t2 = temp_ms;
|
||||
long t_high = 0, t_low = 0;
|
||||
millis_t temp_ms = millis(), t1 = temp_ms, t2 = temp_ms;
|
||||
long t_high = 0, t_low = 0;
|
||||
|
||||
long bias, d;
|
||||
float Ku, Tu;
|
||||
float workKp = 0, workKi = 0, workKd = 0;
|
||||
float max = 0, min = 10000;
|
||||
long bias, d;
|
||||
float Ku, Tu;
|
||||
float workKp = 0, workKi = 0, workKd = 0;
|
||||
float max = 0, min = 10000;
|
||||
|
||||
#if HAS_AUTO_FAN
|
||||
millis_t next_auto_fan_check_ms = temp_ms + 2500UL;
|
||||
#endif
|
||||
|
||||
if (extruder >= EXTRUDERS
|
||||
#if !HAS_TEMP_BED
|
||||
|| extruder < 0
|
||||
#if HAS_AUTO_FAN
|
||||
millis_t next_auto_fan_check_ms = temp_ms + 2500UL;
|
||||
#endif
|
||||
) {
|
||||
SERIAL_ECHOLN(MSG_PID_BAD_EXTRUDER_NUM);
|
||||
return;
|
||||
}
|
||||
|
||||
SERIAL_ECHOLN(MSG_PID_AUTOTUNE_START);
|
||||
|
||||
disable_all_heaters(); // switch off all heaters.
|
||||
|
||||
if (extruder < 0)
|
||||
soft_pwm_bed = bias = d = (MAX_BED_POWER) / 2;
|
||||
else
|
||||
soft_pwm[extruder] = bias = d = (PID_MAX) / 2;
|
||||
|
||||
// PID Tuning loop
|
||||
for (;;) {
|
||||
|
||||
millis_t ms = millis();
|
||||
|
||||
if (temp_meas_ready) { // temp sample ready
|
||||
updateTemperaturesFromRawValues();
|
||||
|
||||
input = (extruder < 0) ? current_temperature_bed : current_temperature[extruder];
|
||||
|
||||
max = max(max, input);
|
||||
min = min(min, input);
|
||||
|
||||
#if HAS_AUTO_FAN
|
||||
if (ELAPSED(ms, next_auto_fan_check_ms)) {
|
||||
checkExtruderAutoFans();
|
||||
next_auto_fan_check_ms = ms + 2500UL;
|
||||
}
|
||||
if (extruder >= EXTRUDERS
|
||||
#if !HAS_TEMP_BED
|
||||
|| extruder < 0
|
||||
#endif
|
||||
) {
|
||||
SERIAL_ECHOLN(MSG_PID_BAD_EXTRUDER_NUM);
|
||||
return;
|
||||
}
|
||||
|
||||
if (heating && input > temp) {
|
||||
if (ELAPSED(ms, t2 + 5000UL)) {
|
||||
heating = false;
|
||||
if (extruder < 0)
|
||||
soft_pwm_bed = (bias - d) >> 1;
|
||||
else
|
||||
soft_pwm[extruder] = (bias - d) >> 1;
|
||||
t1 = ms;
|
||||
t_high = t1 - t2;
|
||||
max = temp;
|
||||
}
|
||||
}
|
||||
SERIAL_ECHOLN(MSG_PID_AUTOTUNE_START);
|
||||
|
||||
if (!heating && input < temp) {
|
||||
if (ELAPSED(ms, t1 + 5000UL)) {
|
||||
heating = true;
|
||||
t2 = ms;
|
||||
t_low = t2 - t1;
|
||||
if (cycles > 0) {
|
||||
long max_pow = extruder < 0 ? MAX_BED_POWER : PID_MAX;
|
||||
bias += (d * (t_high - t_low)) / (t_low + t_high);
|
||||
bias = constrain(bias, 20, max_pow - 20);
|
||||
d = (bias > max_pow / 2) ? max_pow - 1 - bias : bias;
|
||||
disable_all_heaters(); // switch off all heaters.
|
||||
|
||||
SERIAL_PROTOCOLPGM(MSG_BIAS); SERIAL_PROTOCOL(bias);
|
||||
SERIAL_PROTOCOLPGM(MSG_D); SERIAL_PROTOCOL(d);
|
||||
SERIAL_PROTOCOLPGM(MSG_T_MIN); SERIAL_PROTOCOL(min);
|
||||
SERIAL_PROTOCOLPGM(MSG_T_MAX); SERIAL_PROTOCOLLN(max);
|
||||
if (cycles > 2) {
|
||||
Ku = (4.0 * d) / (3.14159265 * (max - min) / 2.0);
|
||||
Tu = ((float)(t_low + t_high) / 1000.0);
|
||||
SERIAL_PROTOCOLPGM(MSG_KU); SERIAL_PROTOCOL(Ku);
|
||||
SERIAL_PROTOCOLPGM(MSG_TU); SERIAL_PROTOCOLLN(Tu);
|
||||
workKp = 0.6 * Ku;
|
||||
workKi = 2 * workKp / Tu;
|
||||
workKd = workKp * Tu / 8;
|
||||
SERIAL_PROTOCOLLNPGM(MSG_CLASSIC_PID);
|
||||
SERIAL_PROTOCOLPGM(MSG_KP); SERIAL_PROTOCOLLN(workKp);
|
||||
SERIAL_PROTOCOLPGM(MSG_KI); SERIAL_PROTOCOLLN(workKi);
|
||||
SERIAL_PROTOCOLPGM(MSG_KD); SERIAL_PROTOCOLLN(workKd);
|
||||
/**
|
||||
workKp = 0.33*Ku;
|
||||
workKi = workKp/Tu;
|
||||
workKd = workKp*Tu/3;
|
||||
SERIAL_PROTOCOLLNPGM(" Some overshoot ");
|
||||
SERIAL_PROTOCOLPGM(" Kp: "); SERIAL_PROTOCOLLN(workKp);
|
||||
SERIAL_PROTOCOLPGM(" Ki: "); SERIAL_PROTOCOLLN(workKi);
|
||||
SERIAL_PROTOCOLPGM(" Kd: "); SERIAL_PROTOCOLLN(workKd);
|
||||
workKp = 0.2*Ku;
|
||||
workKi = 2*workKp/Tu;
|
||||
workKd = workKp*Tu/3;
|
||||
SERIAL_PROTOCOLLNPGM(" No overshoot ");
|
||||
SERIAL_PROTOCOLPGM(" Kp: "); SERIAL_PROTOCOLLN(workKp);
|
||||
SERIAL_PROTOCOLPGM(" Ki: "); SERIAL_PROTOCOLLN(workKi);
|
||||
SERIAL_PROTOCOLPGM(" Kd: "); SERIAL_PROTOCOLLN(workKd);
|
||||
*/
|
||||
}
|
||||
if (extruder < 0)
|
||||
soft_pwm_bed = bias = d = (MAX_BED_POWER) / 2;
|
||||
else
|
||||
soft_pwm[extruder] = bias = d = (PID_MAX) / 2;
|
||||
|
||||
// PID Tuning loop
|
||||
for (;;) {
|
||||
|
||||
millis_t ms = millis();
|
||||
|
||||
if (temp_meas_ready) { // temp sample ready
|
||||
updateTemperaturesFromRawValues();
|
||||
|
||||
input = (extruder < 0) ? current_temperature_bed : current_temperature[extruder];
|
||||
|
||||
max = max(max, input);
|
||||
min = min(min, input);
|
||||
|
||||
#if HAS_AUTO_FAN
|
||||
if (ELAPSED(ms, next_auto_fan_check_ms)) {
|
||||
checkExtruderAutoFans();
|
||||
next_auto_fan_check_ms = ms + 2500UL;
|
||||
}
|
||||
#endif
|
||||
|
||||
if (heating && input > temp) {
|
||||
if (ELAPSED(ms, t2 + 5000UL)) {
|
||||
heating = false;
|
||||
if (extruder < 0)
|
||||
soft_pwm_bed = (bias - d) >> 1;
|
||||
else
|
||||
soft_pwm[extruder] = (bias - d) >> 1;
|
||||
t1 = ms;
|
||||
t_high = t1 - t2;
|
||||
max = temp;
|
||||
}
|
||||
}
|
||||
|
||||
if (!heating && input < temp) {
|
||||
if (ELAPSED(ms, t1 + 5000UL)) {
|
||||
heating = true;
|
||||
t2 = ms;
|
||||
t_low = t2 - t1;
|
||||
if (cycles > 0) {
|
||||
long max_pow = extruder < 0 ? MAX_BED_POWER : PID_MAX;
|
||||
bias += (d * (t_high - t_low)) / (t_low + t_high);
|
||||
bias = constrain(bias, 20, max_pow - 20);
|
||||
d = (bias > max_pow / 2) ? max_pow - 1 - bias : bias;
|
||||
|
||||
SERIAL_PROTOCOLPGM(MSG_BIAS); SERIAL_PROTOCOL(bias);
|
||||
SERIAL_PROTOCOLPGM(MSG_D); SERIAL_PROTOCOL(d);
|
||||
SERIAL_PROTOCOLPGM(MSG_T_MIN); SERIAL_PROTOCOL(min);
|
||||
SERIAL_PROTOCOLPGM(MSG_T_MAX); SERIAL_PROTOCOLLN(max);
|
||||
if (cycles > 2) {
|
||||
Ku = (4.0 * d) / (3.14159265 * (max - min) / 2.0);
|
||||
Tu = ((float)(t_low + t_high) / 1000.0);
|
||||
SERIAL_PROTOCOLPGM(MSG_KU); SERIAL_PROTOCOL(Ku);
|
||||
SERIAL_PROTOCOLPGM(MSG_TU); SERIAL_PROTOCOLLN(Tu);
|
||||
workKp = 0.6 * Ku;
|
||||
workKi = 2 * workKp / Tu;
|
||||
workKd = workKp * Tu / 8;
|
||||
SERIAL_PROTOCOLLNPGM(MSG_CLASSIC_PID);
|
||||
SERIAL_PROTOCOLPGM(MSG_KP); SERIAL_PROTOCOLLN(workKp);
|
||||
SERIAL_PROTOCOLPGM(MSG_KI); SERIAL_PROTOCOLLN(workKi);
|
||||
SERIAL_PROTOCOLPGM(MSG_KD); SERIAL_PROTOCOLLN(workKd);
|
||||
/**
|
||||
workKp = 0.33*Ku;
|
||||
workKi = workKp/Tu;
|
||||
workKd = workKp*Tu/3;
|
||||
SERIAL_PROTOCOLLNPGM(" Some overshoot ");
|
||||
SERIAL_PROTOCOLPGM(" Kp: "); SERIAL_PROTOCOLLN(workKp);
|
||||
SERIAL_PROTOCOLPGM(" Ki: "); SERIAL_PROTOCOLLN(workKi);
|
||||
SERIAL_PROTOCOLPGM(" Kd: "); SERIAL_PROTOCOLLN(workKd);
|
||||
workKp = 0.2*Ku;
|
||||
workKi = 2*workKp/Tu;
|
||||
workKd = workKp*Tu/3;
|
||||
SERIAL_PROTOCOLLNPGM(" No overshoot ");
|
||||
SERIAL_PROTOCOLPGM(" Kp: "); SERIAL_PROTOCOLLN(workKp);
|
||||
SERIAL_PROTOCOLPGM(" Ki: "); SERIAL_PROTOCOLLN(workKi);
|
||||
SERIAL_PROTOCOLPGM(" Kd: "); SERIAL_PROTOCOLLN(workKd);
|
||||
*/
|
||||
}
|
||||
}
|
||||
if (extruder < 0)
|
||||
soft_pwm_bed = (bias + d) >> 1;
|
||||
else
|
||||
soft_pwm[extruder] = (bias + d) >> 1;
|
||||
cycles++;
|
||||
min = temp;
|
||||
}
|
||||
if (extruder < 0)
|
||||
soft_pwm_bed = (bias + d) >> 1;
|
||||
else
|
||||
soft_pwm[extruder] = (bias + d) >> 1;
|
||||
cycles++;
|
||||
min = temp;
|
||||
}
|
||||
}
|
||||
}
|
||||
#define MAX_OVERSHOOT_PID_AUTOTUNE 20
|
||||
if (input > temp + MAX_OVERSHOOT_PID_AUTOTUNE) {
|
||||
SERIAL_PROTOCOLLNPGM(MSG_PID_TEMP_TOO_HIGH);
|
||||
return;
|
||||
}
|
||||
// Every 2 seconds...
|
||||
if (ELAPSED(ms, temp_ms + 2000UL)) {
|
||||
#if HAS_TEMP_HOTEND || HAS_TEMP_BED
|
||||
print_heaterstates();
|
||||
SERIAL_EOL;
|
||||
#endif
|
||||
#define MAX_OVERSHOOT_PID_AUTOTUNE 20
|
||||
if (input > temp + MAX_OVERSHOOT_PID_AUTOTUNE) {
|
||||
SERIAL_PROTOCOLLNPGM(MSG_PID_TEMP_TOO_HIGH);
|
||||
return;
|
||||
}
|
||||
// Every 2 seconds...
|
||||
if (ELAPSED(ms, temp_ms + 2000UL)) {
|
||||
#if HAS_TEMP_HOTEND || HAS_TEMP_BED
|
||||
print_heaterstates();
|
||||
SERIAL_EOL;
|
||||
#endif
|
||||
|
||||
temp_ms = ms;
|
||||
} // every 2 seconds
|
||||
// Over 2 minutes?
|
||||
if (((ms - t1) + (ms - t2)) > (10L * 60L * 1000L * 2L)) {
|
||||
SERIAL_PROTOCOLLNPGM(MSG_PID_TIMEOUT);
|
||||
return;
|
||||
}
|
||||
if (cycles > ncycles) {
|
||||
SERIAL_PROTOCOLLNPGM(MSG_PID_AUTOTUNE_FINISHED);
|
||||
const char* estring = extruder < 0 ? "bed" : "";
|
||||
SERIAL_PROTOCOLPGM("#define DEFAULT_"); SERIAL_PROTOCOL(estring); SERIAL_PROTOCOLPGM("Kp "); SERIAL_PROTOCOLLN(workKp);
|
||||
SERIAL_PROTOCOLPGM("#define DEFAULT_"); SERIAL_PROTOCOL(estring); SERIAL_PROTOCOLPGM("Ki "); SERIAL_PROTOCOLLN(workKi);
|
||||
SERIAL_PROTOCOLPGM("#define DEFAULT_"); SERIAL_PROTOCOL(estring); SERIAL_PROTOCOLPGM("Kd "); SERIAL_PROTOCOLLN(workKd);
|
||||
temp_ms = ms;
|
||||
} // every 2 seconds
|
||||
// Over 2 minutes?
|
||||
if (((ms - t1) + (ms - t2)) > (10L * 60L * 1000L * 2L)) {
|
||||
SERIAL_PROTOCOLLNPGM(MSG_PID_TIMEOUT);
|
||||
return;
|
||||
}
|
||||
if (cycles > ncycles) {
|
||||
SERIAL_PROTOCOLLNPGM(MSG_PID_AUTOTUNE_FINISHED);
|
||||
const char* estring = extruder < 0 ? "bed" : "";
|
||||
SERIAL_PROTOCOLPGM("#define DEFAULT_"); SERIAL_PROTOCOL(estring); SERIAL_PROTOCOLPGM("Kp "); SERIAL_PROTOCOLLN(workKp);
|
||||
SERIAL_PROTOCOLPGM("#define DEFAULT_"); SERIAL_PROTOCOL(estring); SERIAL_PROTOCOLPGM("Ki "); SERIAL_PROTOCOLLN(workKi);
|
||||
SERIAL_PROTOCOLPGM("#define DEFAULT_"); SERIAL_PROTOCOL(estring); SERIAL_PROTOCOLPGM("Kd "); SERIAL_PROTOCOLLN(workKd);
|
||||
|
||||
// Use the result? (As with "M303 U1")
|
||||
if (set_result) {
|
||||
if (extruder < 0) {
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
bedKp = workKp;
|
||||
bedKi = scalePID_i(workKi);
|
||||
bedKd = scalePID_d(workKd);
|
||||
// Use the result? (As with "M303 U1")
|
||||
if (set_result) {
|
||||
if (extruder < 0) {
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
bedKp = workKp;
|
||||
bedKi = scalePID_i(workKi);
|
||||
bedKd = scalePID_d(workKd);
|
||||
updatePID();
|
||||
#endif
|
||||
}
|
||||
else {
|
||||
PID_PARAM(Kp, extruder) = workKp;
|
||||
PID_PARAM(Ki, extruder) = scalePID_i(workKi);
|
||||
PID_PARAM(Kd, extruder) = scalePID_d(workKd);
|
||||
updatePID();
|
||||
#endif
|
||||
}
|
||||
else {
|
||||
PID_PARAM(Kp, extruder) = workKp;
|
||||
PID_PARAM(Ki, extruder) = scalePID_i(workKi);
|
||||
PID_PARAM(Kd, extruder) = scalePID_d(workKd);
|
||||
updatePID();
|
||||
}
|
||||
}
|
||||
return;
|
||||
}
|
||||
return;
|
||||
lcd_update();
|
||||
}
|
||||
lcd_update();
|
||||
}
|
||||
}
|
||||
|
||||
#endif // PIDTEMP
|
||||
|
||||
|
||||
Loading…
Reference in New Issue
Block a user