Upgrades travis Arduino IDE version to 1.6.9

This commit is contained in:
João Brázio 2016-06-10 16:04:01 +01:00
parent 280af07b4c
commit 9b3a0895fd
No known key found for this signature in database
GPG Key ID: F62CFD37DFFDB540

View File

@ -17,10 +17,10 @@ before_install:
#
install:
#
# Install arduino 1.6.8
- wget http://downloads-02.arduino.cc/arduino-1.6.8-linux64.tar.xz
- tar xf arduino-1.6.8-linux64.tar.xz
- sudo mv arduino-1.6.8 /usr/local/share/arduino
# Install arduino 1.6.9
- wget http://downloads-02.arduino.cc/arduino-1.6.9-linux64.tar.xz
- tar xf arduino-1.6.9-linux64.tar.xz
- sudo mv arduino-1.6.9 /usr/local/share/arduino
- ln -s /usr/local/share/arduino/arduino ${TRAVIS_BUILD_DIR}/buildroot/bin/arduino
#
# Install: LiquidCrystal_I2C library
@ -105,7 +105,8 @@ script:
- opt_enable NUM_SERVOS Z_ENDSTOP_SERVO_NR SERVO_ENDSTOP_ANGLES DEACTIVATE_SERVOS_AFTER_MOVE
- build_marlin
#
# Test EEPROM_SETTINGS, EEPROM_CHITCHAT, M100_FREE_MEMORY_WATCHER, INCH_MODE_SUPPORT, TEMPERATURE_UNITS_SUPPORT
# Test EEPROM_SETTINGS, EEPROM_CHITCHAT, M100_FREE_MEMORY_WATCHER,
# INCH_MODE_SUPPORT, TEMPERATURE_UNITS_SUPPORT
#
- restore_configs
- opt_enable EEPROM_SETTINGS EEPROM_CHITCHAT M100_FREE_MEMORY_WATCHER INCH_MODE_SUPPORT TEMPERATURE_UNITS_SUPPORT
@ -130,7 +131,57 @@ script:
- opt_enable BQ_LCD_SMART_CONTROLLER SPEAKER
- build_marlin
#
### LCDS ###
# Enable FILAMENTCHANGEENABLE
#
- restore_configs
- opt_enable FILAMENTCHANGEENABLE ULTIMAKERCONTROLLER
- build_marlin
#
# Enable filament sensor
#
- restore_configs
- opt_enable FILAMENT_WIDTH_SENSOR
- build_marlin
#
# Enable filament sensor with LCD display
#
- opt_enable ULTIMAKERCONTROLLER FILAMENT_LCD_DISPLAY
- build_marlin
#
# Enable BEZIER_CURVE_SUPPORT
#
- restore_configs
- opt_enable_adv BEZIER_CURVE_SUPPORT
- build_marlin
#
# Enable COREXY
#
- restore_configs
- opt_enable COREXY
- build_marlin
#
# Enable COREXZ
#
- restore_configs
- opt_enable COREXZ
- build_marlin
#
# Enable Z_DUAL_STEPPER_DRIVERS, Z_DUAL_ENDSTOPS
#
- restore_configs
- opt_enable_adv Z_DUAL_STEPPER_DRIVERS Z_DUAL_ENDSTOPS
- pins_set RAMPS_14 X_MAX_PIN -1
- opt_set_adv Z2_MAX_PIN 2
- build_marlin
#
# Test PRINTCOUNTER
#
- restore_configs
- opt_enable PRINTCOUNTER
- build_marlin
#
#
######## STANDARD LCD/PANELS ##############
#
# ULTRA_LCD
#
@ -188,25 +239,29 @@ script:
- opt_enable RA_CONTROL_PANEL
- build_marlin
#
### I2C PANELS ###
######## I2C LCD/PANELS ##############
#
# !!!ATTENTION!!!
# Most I2C configurations are failing at the moment because they require
# a different Liquid Crystal library "LiquidTWI2".
#
# LCD_I2C_SAINSMART_YWROBOT
# Failing at the moment needs different library
#
#- restore_configs
#- opt_enable LCD_I2C_SAINSMART_YWROBOT
#- build_marlin
#
# LCD_I2C_PANELOLU2
#
- restore_configs
- opt_enable LCD_I2C_PANELOLU2
- build_marlin
#- restore_configs
#- opt_enable LCD_I2C_PANELOLU2
#- build_marlin
#
# LCD_I2C_VIKI
#
- restore_configs
- opt_enable LCD_I2C_VIKI
- build_marlin
#- restore_configs
#- opt_enable LCD_I2C_VIKI
#- build_marlin
#
# LCM1602
#
@ -214,55 +269,6 @@ script:
- opt_enable LCM1602
- build_marlin
#
# Enable FILAMENTCHANGEENABLE
#
- restore_configs
- opt_enable FILAMENTCHANGEENABLE ULTIMAKERCONTROLLER
- build_marlin
#
# Enable filament sensor
#
- restore_configs
- opt_enable FILAMENT_WIDTH_SENSOR
- build_marlin
#
# Enable filament sensor with LCD display
#
- opt_enable ULTIMAKERCONTROLLER FILAMENT_LCD_DISPLAY
- build_marlin
#
# Enable BEZIER_CURVE_SUPPORT
#
- restore_configs
- opt_enable_adv BEZIER_CURVE_SUPPORT
- build_marlin
#
# Enable COREXY
#
- restore_configs
- opt_enable COREXY
- build_marlin
#
# Enable COREXZ
#
- restore_configs
- opt_enable COREXZ
- build_marlin
#
# Enable Z_DUAL_STEPPER_DRIVERS, Z_DUAL_ENDSTOPS
#
- restore_configs
- opt_enable_adv Z_DUAL_STEPPER_DRIVERS Z_DUAL_ENDSTOPS
- pins_set RAMPS_14 X_MAX_PIN -1
- opt_set_adv Z2_MAX_PIN 2
- build_marlin
#
# Test PRINTCOUNTER
#
- restore_configs
- opt_enable PRINTCOUNTER
- build_marlin
#
#
######## Example Configurations ##############
#