Drop the Z_MIN_PROBE_ENDSTOP option (#13276)
This commit is contained in:
parent
9a6b90f47d
commit
99d0022fae
@ -764,11 +764,11 @@
|
||||
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
/**
|
||||
* Z_MIN_PROBE_ENDSTOP
|
||||
* Z_MIN_PROBE_PIN
|
||||
*
|
||||
* Enable this option for a probe connected to any pin except Z-Min.
|
||||
* (By default Marlin assumes the Z-Max endstop pin.)
|
||||
* To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
|
||||
* Define this pin if the probe is not connected to Z_MIN_PIN.
|
||||
* If not defined the default pin for the selected MOTHERBOARD
|
||||
* will be used. Most of the time the default is what you want.
|
||||
*
|
||||
* - The simplest option is to use a free endstop connector.
|
||||
* - Use 5V for powered (usually inductive) sensors.
|
||||
@ -778,11 +778,8 @@
|
||||
* - normally-closed switches to GND and D32.
|
||||
* - normally-open switches to 5V and D32.
|
||||
*
|
||||
* WARNING: Setting the wrong pin may have unexpected and potentially
|
||||
* disastrous consequences. Use with caution and do your homework.
|
||||
*
|
||||
*/
|
||||
//#define Z_MIN_PROBE_ENDSTOP
|
||||
//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
|
||||
|
||||
/**
|
||||
* Probe Type
|
||||
|
@ -764,11 +764,11 @@
|
||||
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
/**
|
||||
* Z_MIN_PROBE_ENDSTOP
|
||||
* Z_MIN_PROBE_PIN
|
||||
*
|
||||
* Enable this option for a probe connected to any pin except Z-Min.
|
||||
* (By default Marlin assumes the Z-Max endstop pin.)
|
||||
* To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
|
||||
* Define this pin if the probe is not connected to Z_MIN_PIN.
|
||||
* If not defined the default pin for the selected MOTHERBOARD
|
||||
* will be used. Most of the time the default is what you want.
|
||||
*
|
||||
* - The simplest option is to use a free endstop connector.
|
||||
* - Use 5V for powered (usually inductive) sensors.
|
||||
@ -778,11 +778,8 @@
|
||||
* - normally-closed switches to GND and D32.
|
||||
* - normally-open switches to 5V and D32.
|
||||
*
|
||||
* WARNING: Setting the wrong pin may have unexpected and potentially
|
||||
* disastrous consequences. Use with caution and do your homework.
|
||||
*
|
||||
*/
|
||||
//#define Z_MIN_PROBE_ENDSTOP
|
||||
//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
|
||||
|
||||
/**
|
||||
* Probe Type
|
||||
|
@ -770,11 +770,11 @@
|
||||
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
/**
|
||||
* Z_MIN_PROBE_ENDSTOP
|
||||
* Z_MIN_PROBE_PIN
|
||||
*
|
||||
* Enable this option for a probe connected to any pin except Z-Min.
|
||||
* (By default Marlin assumes the Z-Max endstop pin.)
|
||||
* To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
|
||||
* Define this pin if the probe is not connected to Z_MIN_PIN.
|
||||
* If not defined the default pin for the selected MOTHERBOARD
|
||||
* will be used. Most of the time the default is what you want.
|
||||
*
|
||||
* - The simplest option is to use a free endstop connector.
|
||||
* - Use 5V for powered (usually inductive) sensors.
|
||||
@ -784,11 +784,8 @@
|
||||
* - normally-closed switches to GND and D32.
|
||||
* - normally-open switches to 5V and D32.
|
||||
*
|
||||
* WARNING: Setting the wrong pin may have unexpected and potentially
|
||||
* disastrous consequences. Use with caution and do your homework.
|
||||
*
|
||||
*/
|
||||
//#define Z_MIN_PROBE_ENDSTOP
|
||||
//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
|
||||
|
||||
/**
|
||||
* Probe Type
|
||||
|
@ -784,11 +784,11 @@
|
||||
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
/**
|
||||
* Z_MIN_PROBE_ENDSTOP
|
||||
* Z_MIN_PROBE_PIN
|
||||
*
|
||||
* Enable this option for a probe connected to any pin except Z-Min.
|
||||
* (By default Marlin assumes the Z-Max endstop pin.)
|
||||
* To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
|
||||
* Define this pin if the probe is not connected to Z_MIN_PIN.
|
||||
* If not defined the default pin for the selected MOTHERBOARD
|
||||
* will be used. Most of the time the default is what you want.
|
||||
*
|
||||
* - The simplest option is to use a free endstop connector.
|
||||
* - Use 5V for powered (usually inductive) sensors.
|
||||
@ -798,11 +798,8 @@
|
||||
* - normally-closed switches to GND and D32.
|
||||
* - normally-open switches to 5V and D32.
|
||||
*
|
||||
* WARNING: Setting the wrong pin may have unexpected and potentially
|
||||
* disastrous consequences. Use with caution and do your homework.
|
||||
*
|
||||
*/
|
||||
//#define Z_MIN_PROBE_ENDSTOP
|
||||
//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
|
||||
|
||||
/**
|
||||
* Probe Type
|
||||
|
@ -764,11 +764,11 @@
|
||||
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
/**
|
||||
* Z_MIN_PROBE_ENDSTOP
|
||||
* Z_MIN_PROBE_PIN
|
||||
*
|
||||
* Enable this option for a probe connected to any pin except Z-Min.
|
||||
* (By default Marlin assumes the Z-Max endstop pin.)
|
||||
* To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
|
||||
* Define this pin if the probe is not connected to Z_MIN_PIN.
|
||||
* If not defined the default pin for the selected MOTHERBOARD
|
||||
* will be used. Most of the time the default is what you want.
|
||||
*
|
||||
* - The simplest option is to use a free endstop connector.
|
||||
* - Use 5V for powered (usually inductive) sensors.
|
||||
@ -778,11 +778,8 @@
|
||||
* - normally-closed switches to GND and D32.
|
||||
* - normally-open switches to 5V and D32.
|
||||
*
|
||||
* WARNING: Setting the wrong pin may have unexpected and potentially
|
||||
* disastrous consequences. Use with caution and do your homework.
|
||||
*
|
||||
*/
|
||||
//#define Z_MIN_PROBE_ENDSTOP
|
||||
//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
|
||||
|
||||
/**
|
||||
* Probe Type
|
||||
|
@ -764,11 +764,11 @@
|
||||
//#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
/**
|
||||
* Z_MIN_PROBE_ENDSTOP
|
||||
* Z_MIN_PROBE_PIN
|
||||
*
|
||||
* Enable this option for a probe connected to any pin except Z-Min.
|
||||
* (By default Marlin assumes the Z-Max endstop pin.)
|
||||
* To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
|
||||
* Define this pin if the probe is not connected to Z_MIN_PIN.
|
||||
* If not defined the default pin for the selected MOTHERBOARD
|
||||
* will be used. Most of the time the default is what you want.
|
||||
*
|
||||
* - The simplest option is to use a free endstop connector.
|
||||
* - Use 5V for powered (usually inductive) sensors.
|
||||
@ -778,11 +778,8 @@
|
||||
* - normally-closed switches to GND and D32.
|
||||
* - normally-open switches to 5V and D32.
|
||||
*
|
||||
* WARNING: Setting the wrong pin may have unexpected and potentially
|
||||
* disastrous consequences. Use with caution and do your homework.
|
||||
*
|
||||
*/
|
||||
//#define Z_MIN_PROBE_ENDSTOP
|
||||
//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
|
||||
|
||||
/**
|
||||
* Probe Type
|
||||
|
@ -764,11 +764,11 @@
|
||||
//#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
/**
|
||||
* Z_MIN_PROBE_ENDSTOP
|
||||
* Z_MIN_PROBE_PIN
|
||||
*
|
||||
* Enable this option for a probe connected to any pin except Z-Min.
|
||||
* (By default Marlin assumes the Z-Max endstop pin.)
|
||||
* To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
|
||||
* Define this pin if the probe is not connected to Z_MIN_PIN.
|
||||
* If not defined the default pin for the selected MOTHERBOARD
|
||||
* will be used. Most of the time the default is what you want.
|
||||
*
|
||||
* - The simplest option is to use a free endstop connector.
|
||||
* - Use 5V for powered (usually inductive) sensors.
|
||||
@ -778,11 +778,8 @@
|
||||
* - normally-closed switches to GND and D32.
|
||||
* - normally-open switches to 5V and D32.
|
||||
*
|
||||
* WARNING: Setting the wrong pin may have unexpected and potentially
|
||||
* disastrous consequences. Use with caution and do your homework.
|
||||
*
|
||||
*/
|
||||
//#define Z_MIN_PROBE_ENDSTOP
|
||||
//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
|
||||
|
||||
/**
|
||||
* Probe Type
|
||||
|
@ -811,11 +811,11 @@
|
||||
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
/**
|
||||
* Z_MIN_PROBE_ENDSTOP
|
||||
* Z_MIN_PROBE_PIN
|
||||
*
|
||||
* Enable this option for a probe connected to any pin except Z-Min.
|
||||
* (By default Marlin assumes the Z-Max endstop pin.)
|
||||
* To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
|
||||
* Define this pin if the probe is not connected to Z_MIN_PIN.
|
||||
* If not defined the default pin for the selected MOTHERBOARD
|
||||
* will be used. Most of the time the default is what you want.
|
||||
*
|
||||
* - The simplest option is to use a free endstop connector.
|
||||
* - Use 5V for powered (usually inductive) sensors.
|
||||
@ -825,11 +825,8 @@
|
||||
* - normally-closed switches to GND and D32.
|
||||
* - normally-open switches to 5V and D32.
|
||||
*
|
||||
* WARNING: Setting the wrong pin may have unexpected and potentially
|
||||
* disastrous consequences. Use with caution and do your homework.
|
||||
*
|
||||
*/
|
||||
//#define Z_MIN_PROBE_ENDSTOP
|
||||
//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
|
||||
|
||||
/**
|
||||
* Probe Type
|
||||
|
@ -777,11 +777,11 @@
|
||||
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
/**
|
||||
* Z_MIN_PROBE_ENDSTOP
|
||||
* Z_MIN_PROBE_PIN
|
||||
*
|
||||
* Enable this option for a probe connected to any pin except Z-Min.
|
||||
* (By default Marlin assumes the Z-Max endstop pin.)
|
||||
* To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
|
||||
* Define this pin if the probe is not connected to Z_MIN_PIN.
|
||||
* If not defined the default pin for the selected MOTHERBOARD
|
||||
* will be used. Most of the time the default is what you want.
|
||||
*
|
||||
* - The simplest option is to use a free endstop connector.
|
||||
* - Use 5V for powered (usually inductive) sensors.
|
||||
@ -791,11 +791,8 @@
|
||||
* - normally-closed switches to GND and D32.
|
||||
* - normally-open switches to 5V and D32.
|
||||
*
|
||||
* WARNING: Setting the wrong pin may have unexpected and potentially
|
||||
* disastrous consequences. Use with caution and do your homework.
|
||||
*
|
||||
*/
|
||||
//#define Z_MIN_PROBE_ENDSTOP
|
||||
//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
|
||||
|
||||
/**
|
||||
* Probe Type
|
||||
|
@ -774,11 +774,11 @@
|
||||
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
/**
|
||||
* Z_MIN_PROBE_ENDSTOP
|
||||
* Z_MIN_PROBE_PIN
|
||||
*
|
||||
* Enable this option for a probe connected to any pin except Z-Min.
|
||||
* (By default Marlin assumes the Z-Max endstop pin.)
|
||||
* To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
|
||||
* Define this pin if the probe is not connected to Z_MIN_PIN.
|
||||
* If not defined the default pin for the selected MOTHERBOARD
|
||||
* will be used. Most of the time the default is what you want.
|
||||
*
|
||||
* - The simplest option is to use a free endstop connector.
|
||||
* - Use 5V for powered (usually inductive) sensors.
|
||||
@ -788,11 +788,8 @@
|
||||
* - normally-closed switches to GND and D32.
|
||||
* - normally-open switches to 5V and D32.
|
||||
*
|
||||
* WARNING: Setting the wrong pin may have unexpected and potentially
|
||||
* disastrous consequences. Use with caution and do your homework.
|
||||
*
|
||||
*/
|
||||
//#define Z_MIN_PROBE_ENDSTOP
|
||||
//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
|
||||
|
||||
/**
|
||||
* Probe Type
|
||||
|
@ -765,11 +765,11 @@
|
||||
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
/**
|
||||
* Z_MIN_PROBE_ENDSTOP
|
||||
* Z_MIN_PROBE_PIN
|
||||
*
|
||||
* Enable this option for a probe connected to any pin except Z-Min.
|
||||
* (By default Marlin assumes the Z-Max endstop pin.)
|
||||
* To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
|
||||
* Define this pin if the probe is not connected to Z_MIN_PIN.
|
||||
* If not defined the default pin for the selected MOTHERBOARD
|
||||
* will be used. Most of the time the default is what you want.
|
||||
*
|
||||
* - The simplest option is to use a free endstop connector.
|
||||
* - Use 5V for powered (usually inductive) sensors.
|
||||
@ -779,11 +779,8 @@
|
||||
* - normally-closed switches to GND and D32.
|
||||
* - normally-open switches to 5V and D32.
|
||||
*
|
||||
* WARNING: Setting the wrong pin may have unexpected and potentially
|
||||
* disastrous consequences. Use with caution and do your homework.
|
||||
*
|
||||
*/
|
||||
//#define Z_MIN_PROBE_ENDSTOP
|
||||
//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
|
||||
|
||||
/**
|
||||
* Probe Type
|
||||
|
@ -764,11 +764,11 @@
|
||||
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
/**
|
||||
* Z_MIN_PROBE_ENDSTOP
|
||||
* Z_MIN_PROBE_PIN
|
||||
*
|
||||
* Enable this option for a probe connected to any pin except Z-Min.
|
||||
* (By default Marlin assumes the Z-Max endstop pin.)
|
||||
* To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
|
||||
* Define this pin if the probe is not connected to Z_MIN_PIN.
|
||||
* If not defined the default pin for the selected MOTHERBOARD
|
||||
* will be used. Most of the time the default is what you want.
|
||||
*
|
||||
* - The simplest option is to use a free endstop connector.
|
||||
* - Use 5V for powered (usually inductive) sensors.
|
||||
@ -778,11 +778,8 @@
|
||||
* - normally-closed switches to GND and D32.
|
||||
* - normally-open switches to 5V and D32.
|
||||
*
|
||||
* WARNING: Setting the wrong pin may have unexpected and potentially
|
||||
* disastrous consequences. Use with caution and do your homework.
|
||||
*
|
||||
*/
|
||||
//#define Z_MIN_PROBE_ENDSTOP
|
||||
//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
|
||||
|
||||
/**
|
||||
* Probe Type
|
||||
|
@ -764,11 +764,11 @@
|
||||
//#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
/**
|
||||
* Z_MIN_PROBE_ENDSTOP
|
||||
* Z_MIN_PROBE_PIN
|
||||
*
|
||||
* Enable this option for a probe connected to any pin except Z-Min.
|
||||
* (By default Marlin assumes the Z-Max endstop pin.)
|
||||
* To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
|
||||
* Define this pin if the probe is not connected to Z_MIN_PIN.
|
||||
* If not defined the default pin for the selected MOTHERBOARD
|
||||
* will be used. Most of the time the default is what you want.
|
||||
*
|
||||
* - The simplest option is to use a free endstop connector.
|
||||
* - Use 5V for powered (usually inductive) sensors.
|
||||
@ -778,11 +778,8 @@
|
||||
* - normally-closed switches to GND and D32.
|
||||
* - normally-open switches to 5V and D32.
|
||||
*
|
||||
* WARNING: Setting the wrong pin may have unexpected and potentially
|
||||
* disastrous consequences. Use with caution and do your homework.
|
||||
*
|
||||
*/
|
||||
//#define Z_MIN_PROBE_ENDSTOP
|
||||
//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
|
||||
|
||||
/**
|
||||
* Probe Type
|
||||
|
@ -764,11 +764,11 @@
|
||||
//#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
/**
|
||||
* Z_MIN_PROBE_ENDSTOP
|
||||
* Z_MIN_PROBE_PIN
|
||||
*
|
||||
* Enable this option for a probe connected to any pin except Z-Min.
|
||||
* (By default Marlin assumes the Z-Max endstop pin.)
|
||||
* To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
|
||||
* Define this pin if the probe is not connected to Z_MIN_PIN.
|
||||
* If not defined the default pin for the selected MOTHERBOARD
|
||||
* will be used. Most of the time the default is what you want.
|
||||
*
|
||||
* - The simplest option is to use a free endstop connector.
|
||||
* - Use 5V for powered (usually inductive) sensors.
|
||||
@ -778,11 +778,8 @@
|
||||
* - normally-closed switches to GND and D32.
|
||||
* - normally-open switches to 5V and D32.
|
||||
*
|
||||
* WARNING: Setting the wrong pin may have unexpected and potentially
|
||||
* disastrous consequences. Use with caution and do your homework.
|
||||
*
|
||||
*/
|
||||
//#define Z_MIN_PROBE_ENDSTOP
|
||||
//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
|
||||
|
||||
/**
|
||||
* Probe Type
|
||||
|
@ -752,11 +752,11 @@
|
||||
//#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
/**
|
||||
* Z_MIN_PROBE_ENDSTOP
|
||||
* Z_MIN_PROBE_PIN
|
||||
*
|
||||
* Enable this option for a probe connected to any pin except Z-Min.
|
||||
* (By default Marlin assumes the Z-Max endstop pin.)
|
||||
* To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
|
||||
* Define this pin if the probe is not connected to Z_MIN_PIN.
|
||||
* If not defined the default pin for the selected MOTHERBOARD
|
||||
* will be used. Most of the time the default is what you want.
|
||||
*
|
||||
* - The simplest option is to use a free endstop connector.
|
||||
* - Use 5V for powered (usually inductive) sensors.
|
||||
@ -766,11 +766,8 @@
|
||||
* - normally-closed switches to GND and D32.
|
||||
* - normally-open switches to 5V and D32.
|
||||
*
|
||||
* WARNING: Setting the wrong pin may have unexpected and potentially
|
||||
* disastrous consequences. Use with caution and do your homework.
|
||||
*
|
||||
*/
|
||||
#define Z_MIN_PROBE_ENDSTOP
|
||||
//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
|
||||
|
||||
/**
|
||||
* Probe Type
|
||||
|
@ -765,11 +765,11 @@
|
||||
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
/**
|
||||
* Z_MIN_PROBE_ENDSTOP
|
||||
* Z_MIN_PROBE_PIN
|
||||
*
|
||||
* Enable this option for a probe connected to any pin except Z-Min.
|
||||
* (By default Marlin assumes the Z-Max endstop pin.)
|
||||
* To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
|
||||
* Define this pin if the probe is not connected to Z_MIN_PIN.
|
||||
* If not defined the default pin for the selected MOTHERBOARD
|
||||
* will be used. Most of the time the default is what you want.
|
||||
*
|
||||
* - The simplest option is to use a free endstop connector.
|
||||
* - Use 5V for powered (usually inductive) sensors.
|
||||
@ -779,11 +779,8 @@
|
||||
* - normally-closed switches to GND and D32.
|
||||
* - normally-open switches to 5V and D32.
|
||||
*
|
||||
* WARNING: Setting the wrong pin may have unexpected and potentially
|
||||
* disastrous consequences. Use with caution and do your homework.
|
||||
*
|
||||
*/
|
||||
//#define Z_MIN_PROBE_ENDSTOP
|
||||
//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
|
||||
|
||||
/**
|
||||
* Probe Type
|
||||
|
@ -752,11 +752,11 @@
|
||||
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
/**
|
||||
* Z_MIN_PROBE_ENDSTOP
|
||||
* Z_MIN_PROBE_PIN
|
||||
*
|
||||
* Enable this option for a probe connected to any pin except Z-Min.
|
||||
* (By default Marlin assumes the Z-Max endstop pin.)
|
||||
* To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
|
||||
* Define this pin if the probe is not connected to Z_MIN_PIN.
|
||||
* If not defined the default pin for the selected MOTHERBOARD
|
||||
* will be used. Most of the time the default is what you want.
|
||||
*
|
||||
* - The simplest option is to use a free endstop connector.
|
||||
* - Use 5V for powered (usually inductive) sensors.
|
||||
@ -766,11 +766,8 @@
|
||||
* - normally-closed switches to GND and D32.
|
||||
* - normally-open switches to 5V and D32.
|
||||
*
|
||||
* WARNING: Setting the wrong pin may have unexpected and potentially
|
||||
* disastrous consequences. Use with caution and do your homework.
|
||||
*
|
||||
*/
|
||||
//#define Z_MIN_PROBE_ENDSTOP
|
||||
//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
|
||||
|
||||
/**
|
||||
* Probe Type
|
||||
|
@ -763,11 +763,11 @@
|
||||
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
/**
|
||||
* Z_MIN_PROBE_ENDSTOP
|
||||
* Z_MIN_PROBE_PIN
|
||||
*
|
||||
* Enable this option for a probe connected to any pin except Z-Min.
|
||||
* (By default Marlin assumes the Z-Max endstop pin.)
|
||||
* To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
|
||||
* Define this pin if the probe is not connected to Z_MIN_PIN.
|
||||
* If not defined the default pin for the selected MOTHERBOARD
|
||||
* will be used. Most of the time the default is what you want.
|
||||
*
|
||||
* - The simplest option is to use a free endstop connector.
|
||||
* - Use 5V for powered (usually inductive) sensors.
|
||||
@ -777,11 +777,8 @@
|
||||
* - normally-closed switches to GND and D32.
|
||||
* - normally-open switches to 5V and D32.
|
||||
*
|
||||
* WARNING: Setting the wrong pin may have unexpected and potentially
|
||||
* disastrous consequences. Use with caution and do your homework.
|
||||
*
|
||||
*/
|
||||
//#define Z_MIN_PROBE_ENDSTOP
|
||||
//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
|
||||
|
||||
/**
|
||||
* Probe Type
|
||||
|
@ -774,11 +774,11 @@
|
||||
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
/**
|
||||
* Z_MIN_PROBE_ENDSTOP
|
||||
* Z_MIN_PROBE_PIN
|
||||
*
|
||||
* Enable this option for a probe connected to any pin except Z-Min.
|
||||
* (By default Marlin assumes the Z-Max endstop pin.)
|
||||
* To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
|
||||
* Define this pin if the probe is not connected to Z_MIN_PIN.
|
||||
* If not defined the default pin for the selected MOTHERBOARD
|
||||
* will be used. Most of the time the default is what you want.
|
||||
*
|
||||
* - The simplest option is to use a free endstop connector.
|
||||
* - Use 5V for powered (usually inductive) sensors.
|
||||
@ -788,11 +788,8 @@
|
||||
* - normally-closed switches to GND and D32.
|
||||
* - normally-open switches to 5V and D32.
|
||||
*
|
||||
* WARNING: Setting the wrong pin may have unexpected and potentially
|
||||
* disastrous consequences. Use with caution and do your homework.
|
||||
*
|
||||
*/
|
||||
//#define Z_MIN_PROBE_ENDSTOP
|
||||
//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
|
||||
|
||||
/**
|
||||
* Probe Type
|
||||
|
@ -764,11 +764,11 @@
|
||||
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
/**
|
||||
* Z_MIN_PROBE_ENDSTOP
|
||||
* Z_MIN_PROBE_PIN
|
||||
*
|
||||
* Enable this option for a probe connected to any pin except Z-Min.
|
||||
* (By default Marlin assumes the Z-Max endstop pin.)
|
||||
* To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
|
||||
* Define this pin if the probe is not connected to Z_MIN_PIN.
|
||||
* If not defined the default pin for the selected MOTHERBOARD
|
||||
* will be used. Most of the time the default is what you want.
|
||||
*
|
||||
* - The simplest option is to use a free endstop connector.
|
||||
* - Use 5V for powered (usually inductive) sensors.
|
||||
@ -778,11 +778,8 @@
|
||||
* - normally-closed switches to GND and D32.
|
||||
* - normally-open switches to 5V and D32.
|
||||
*
|
||||
* WARNING: Setting the wrong pin may have unexpected and potentially
|
||||
* disastrous consequences. Use with caution and do your homework.
|
||||
*
|
||||
*/
|
||||
//#define Z_MIN_PROBE_ENDSTOP
|
||||
//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
|
||||
|
||||
/**
|
||||
* Probe Type
|
||||
|
@ -765,11 +765,11 @@
|
||||
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
/**
|
||||
* Z_MIN_PROBE_ENDSTOP
|
||||
* Z_MIN_PROBE_PIN
|
||||
*
|
||||
* Enable this option for a probe connected to any pin except Z-Min.
|
||||
* (By default Marlin assumes the Z-Max endstop pin.)
|
||||
* To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
|
||||
* Define this pin if the probe is not connected to Z_MIN_PIN.
|
||||
* If not defined the default pin for the selected MOTHERBOARD
|
||||
* will be used. Most of the time the default is what you want.
|
||||
*
|
||||
* - The simplest option is to use a free endstop connector.
|
||||
* - Use 5V for powered (usually inductive) sensors.
|
||||
@ -779,11 +779,8 @@
|
||||
* - normally-closed switches to GND and D32.
|
||||
* - normally-open switches to 5V and D32.
|
||||
*
|
||||
* WARNING: Setting the wrong pin may have unexpected and potentially
|
||||
* disastrous consequences. Use with caution and do your homework.
|
||||
*
|
||||
*/
|
||||
//#define Z_MIN_PROBE_ENDSTOP
|
||||
//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
|
||||
|
||||
/**
|
||||
* Probe Type
|
||||
|
@ -783,11 +783,11 @@
|
||||
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
/**
|
||||
* Z_MIN_PROBE_ENDSTOP
|
||||
* Z_MIN_PROBE_PIN
|
||||
*
|
||||
* Enable this option for a probe connected to any pin except Z-Min.
|
||||
* (By default Marlin assumes the Z-Max endstop pin.)
|
||||
* To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
|
||||
* Define this pin if the probe is not connected to Z_MIN_PIN.
|
||||
* If not defined the default pin for the selected MOTHERBOARD
|
||||
* will be used. Most of the time the default is what you want.
|
||||
*
|
||||
* - The simplest option is to use a free endstop connector.
|
||||
* - Use 5V for powered (usually inductive) sensors.
|
||||
@ -797,11 +797,8 @@
|
||||
* - normally-closed switches to GND and D32.
|
||||
* - normally-open switches to 5V and D32.
|
||||
*
|
||||
* WARNING: Setting the wrong pin may have unexpected and potentially
|
||||
* disastrous consequences. Use with caution and do your homework.
|
||||
*
|
||||
*/
|
||||
//#define Z_MIN_PROBE_ENDSTOP
|
||||
//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
|
||||
|
||||
/**
|
||||
* Probe Type
|
||||
|
@ -774,11 +774,11 @@
|
||||
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
/**
|
||||
* Z_MIN_PROBE_ENDSTOP
|
||||
* Z_MIN_PROBE_PIN
|
||||
*
|
||||
* Enable this option for a probe connected to any pin except Z-Min.
|
||||
* (By default Marlin assumes the Z-Max endstop pin.)
|
||||
* To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
|
||||
* Define this pin if the probe is not connected to Z_MIN_PIN.
|
||||
* If not defined the default pin for the selected MOTHERBOARD
|
||||
* will be used. Most of the time the default is what you want.
|
||||
*
|
||||
* - The simplest option is to use a free endstop connector.
|
||||
* - Use 5V for powered (usually inductive) sensors.
|
||||
@ -788,11 +788,8 @@
|
||||
* - normally-closed switches to GND and D32.
|
||||
* - normally-open switches to 5V and D32.
|
||||
*
|
||||
* WARNING: Setting the wrong pin may have unexpected and potentially
|
||||
* disastrous consequences. Use with caution and do your homework.
|
||||
*
|
||||
*/
|
||||
//#define Z_MIN_PROBE_ENDSTOP
|
||||
//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
|
||||
|
||||
/**
|
||||
* Probe Type
|
||||
|
@ -768,11 +768,11 @@
|
||||
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
/**
|
||||
* Z_MIN_PROBE_ENDSTOP
|
||||
* Z_MIN_PROBE_PIN
|
||||
*
|
||||
* Enable this option for a probe connected to any pin except Z-Min.
|
||||
* (By default Marlin assumes the Z-Max endstop pin.)
|
||||
* To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
|
||||
* Define this pin if the probe is not connected to Z_MIN_PIN.
|
||||
* If not defined the default pin for the selected MOTHERBOARD
|
||||
* will be used. Most of the time the default is what you want.
|
||||
*
|
||||
* - The simplest option is to use a free endstop connector.
|
||||
* - Use 5V for powered (usually inductive) sensors.
|
||||
@ -782,11 +782,8 @@
|
||||
* - normally-closed switches to GND and D32.
|
||||
* - normally-open switches to 5V and D32.
|
||||
*
|
||||
* WARNING: Setting the wrong pin may have unexpected and potentially
|
||||
* disastrous consequences. Use with caution and do your homework.
|
||||
*
|
||||
*/
|
||||
//#define Z_MIN_PROBE_ENDSTOP
|
||||
//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
|
||||
|
||||
/**
|
||||
* Probe Type
|
||||
|
@ -768,11 +768,11 @@
|
||||
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
/**
|
||||
* Z_MIN_PROBE_ENDSTOP
|
||||
* Z_MIN_PROBE_PIN
|
||||
*
|
||||
* Enable this option for a probe connected to any pin except Z-Min.
|
||||
* (By default Marlin assumes the Z-Max endstop pin.)
|
||||
* To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
|
||||
* Define this pin if the probe is not connected to Z_MIN_PIN.
|
||||
* If not defined the default pin for the selected MOTHERBOARD
|
||||
* will be used. Most of the time the default is what you want.
|
||||
*
|
||||
* - The simplest option is to use a free endstop connector.
|
||||
* - Use 5V for powered (usually inductive) sensors.
|
||||
@ -782,11 +782,8 @@
|
||||
* - normally-closed switches to GND and D32.
|
||||
* - normally-open switches to 5V and D32.
|
||||
*
|
||||
* WARNING: Setting the wrong pin may have unexpected and potentially
|
||||
* disastrous consequences. Use with caution and do your homework.
|
||||
*
|
||||
*/
|
||||
//#define Z_MIN_PROBE_ENDSTOP
|
||||
//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
|
||||
|
||||
/**
|
||||
* Probe Type
|
||||
|
@ -774,11 +774,11 @@
|
||||
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
/**
|
||||
* Z_MIN_PROBE_ENDSTOP
|
||||
* Z_MIN_PROBE_PIN
|
||||
*
|
||||
* Enable this option for a probe connected to any pin except Z-Min.
|
||||
* (By default Marlin assumes the Z-Max endstop pin.)
|
||||
* To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
|
||||
* Define this pin if the probe is not connected to Z_MIN_PIN.
|
||||
* If not defined the default pin for the selected MOTHERBOARD
|
||||
* will be used. Most of the time the default is what you want.
|
||||
*
|
||||
* - The simplest option is to use a free endstop connector.
|
||||
* - Use 5V for powered (usually inductive) sensors.
|
||||
@ -788,11 +788,8 @@
|
||||
* - normally-closed switches to GND and D32.
|
||||
* - normally-open switches to 5V and D32.
|
||||
*
|
||||
* WARNING: Setting the wrong pin may have unexpected and potentially
|
||||
* disastrous consequences. Use with caution and do your homework.
|
||||
*
|
||||
*/
|
||||
//#define Z_MIN_PROBE_ENDSTOP
|
||||
//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
|
||||
|
||||
/**
|
||||
* Probe Type
|
||||
|
@ -776,11 +776,11 @@
|
||||
//#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
/**
|
||||
* Z_MIN_PROBE_ENDSTOP
|
||||
* Z_MIN_PROBE_PIN
|
||||
*
|
||||
* Enable this option for a probe connected to any pin except Z-Min.
|
||||
* (By default Marlin assumes the Z-Max endstop pin.)
|
||||
* To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
|
||||
* Define this pin if the probe is not connected to Z_MIN_PIN.
|
||||
* If not defined the default pin for the selected MOTHERBOARD
|
||||
* will be used. Most of the time the default is what you want.
|
||||
*
|
||||
* - The simplest option is to use a free endstop connector.
|
||||
* - Use 5V for powered (usually inductive) sensors.
|
||||
@ -790,11 +790,8 @@
|
||||
* - normally-closed switches to GND and D32.
|
||||
* - normally-open switches to 5V and D32.
|
||||
*
|
||||
* WARNING: Setting the wrong pin may have unexpected and potentially
|
||||
* disastrous consequences. Use with caution and do your homework.
|
||||
*
|
||||
*/
|
||||
//#define Z_MIN_PROBE_ENDSTOP
|
||||
//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
|
||||
|
||||
/**
|
||||
* Probe Type
|
||||
|
@ -746,11 +746,11 @@
|
||||
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
/**
|
||||
* Z_MIN_PROBE_ENDSTOP
|
||||
* Z_MIN_PROBE_PIN
|
||||
*
|
||||
* Enable this option for a probe connected to any pin except Z-Min.
|
||||
* (By default Marlin assumes the Z-Max endstop pin.)
|
||||
* To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
|
||||
* Define this pin if the probe is not connected to Z_MIN_PIN.
|
||||
* If not defined the default pin for the selected MOTHERBOARD
|
||||
* will be used. Most of the time the default is what you want.
|
||||
*
|
||||
* - The simplest option is to use a free endstop connector.
|
||||
* - Use 5V for powered (usually inductive) sensors.
|
||||
@ -760,11 +760,8 @@
|
||||
* - normally-closed switches to GND and D32.
|
||||
* - normally-open switches to 5V and D32.
|
||||
*
|
||||
* WARNING: Setting the wrong pin may have unexpected and potentially
|
||||
* disastrous consequences. Use with caution and do your homework.
|
||||
*
|
||||
*/
|
||||
//#define Z_MIN_PROBE_ENDSTOP
|
||||
//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
|
||||
|
||||
/**
|
||||
* Probe Type
|
||||
|
@ -746,11 +746,11 @@
|
||||
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
/**
|
||||
* Z_MIN_PROBE_ENDSTOP
|
||||
* Z_MIN_PROBE_PIN
|
||||
*
|
||||
* Enable this option for a probe connected to any pin except Z-Min.
|
||||
* (By default Marlin assumes the Z-Max endstop pin.)
|
||||
* To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
|
||||
* Define this pin if the probe is not connected to Z_MIN_PIN.
|
||||
* If not defined the default pin for the selected MOTHERBOARD
|
||||
* will be used. Most of the time the default is what you want.
|
||||
*
|
||||
* - The simplest option is to use a free endstop connector.
|
||||
* - Use 5V for powered (usually inductive) sensors.
|
||||
@ -760,11 +760,8 @@
|
||||
* - normally-closed switches to GND and D32.
|
||||
* - normally-open switches to 5V and D32.
|
||||
*
|
||||
* WARNING: Setting the wrong pin may have unexpected and potentially
|
||||
* disastrous consequences. Use with caution and do your homework.
|
||||
*
|
||||
*/
|
||||
//#define Z_MIN_PROBE_ENDSTOP
|
||||
//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
|
||||
|
||||
/**
|
||||
* Probe Type
|
||||
|
@ -756,11 +756,11 @@
|
||||
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
/**
|
||||
* Z_MIN_PROBE_ENDSTOP
|
||||
* Z_MIN_PROBE_PIN
|
||||
*
|
||||
* Enable this option for a probe connected to any pin except Z-Min.
|
||||
* (By default Marlin assumes the Z-Max endstop pin.)
|
||||
* To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
|
||||
* Define this pin if the probe is not connected to Z_MIN_PIN.
|
||||
* If not defined the default pin for the selected MOTHERBOARD
|
||||
* will be used. Most of the time the default is what you want.
|
||||
*
|
||||
* - The simplest option is to use a free endstop connector.
|
||||
* - Use 5V for powered (usually inductive) sensors.
|
||||
@ -770,11 +770,8 @@
|
||||
* - normally-closed switches to GND and D32.
|
||||
* - normally-open switches to 5V and D32.
|
||||
*
|
||||
* WARNING: Setting the wrong pin may have unexpected and potentially
|
||||
* disastrous consequences. Use with caution and do your homework.
|
||||
*
|
||||
*/
|
||||
//#define Z_MIN_PROBE_ENDSTOP
|
||||
//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
|
||||
|
||||
/**
|
||||
* Probe Type
|
||||
|
@ -770,11 +770,11 @@
|
||||
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
/**
|
||||
* Z_MIN_PROBE_ENDSTOP
|
||||
* Z_MIN_PROBE_PIN
|
||||
*
|
||||
* Enable this option for a probe connected to any pin except Z-Min.
|
||||
* (By default Marlin assumes the Z-Max endstop pin.)
|
||||
* To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
|
||||
* Define this pin if the probe is not connected to Z_MIN_PIN.
|
||||
* If not defined the default pin for the selected MOTHERBOARD
|
||||
* will be used. Most of the time the default is what you want.
|
||||
*
|
||||
* - The simplest option is to use a free endstop connector.
|
||||
* - Use 5V for powered (usually inductive) sensors.
|
||||
@ -784,11 +784,8 @@
|
||||
* - normally-closed switches to GND and D32.
|
||||
* - normally-open switches to 5V and D32.
|
||||
*
|
||||
* WARNING: Setting the wrong pin may have unexpected and potentially
|
||||
* disastrous consequences. Use with caution and do your homework.
|
||||
*
|
||||
*/
|
||||
//#define Z_MIN_PROBE_ENDSTOP
|
||||
//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
|
||||
|
||||
/**
|
||||
* Probe Type
|
||||
|
@ -847,11 +847,11 @@
|
||||
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
/**
|
||||
* Z_MIN_PROBE_ENDSTOP
|
||||
* Z_MIN_PROBE_PIN
|
||||
*
|
||||
* Enable this option for a probe connected to any pin except Z-Min.
|
||||
* (By default Marlin assumes the Z-Max endstop pin.)
|
||||
* To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
|
||||
* Define this pin if the probe is not connected to Z_MIN_PIN.
|
||||
* If not defined the default pin for the selected MOTHERBOARD
|
||||
* will be used. Most of the time the default is what you want.
|
||||
*
|
||||
* - The simplest option is to use a free endstop connector.
|
||||
* - Use 5V for powered (usually inductive) sensors.
|
||||
@ -861,11 +861,8 @@
|
||||
* - normally-closed switches to GND and D32.
|
||||
* - normally-open switches to 5V and D32.
|
||||
*
|
||||
* WARNING: Setting the wrong pin may have unexpected and potentially
|
||||
* disastrous consequences. Use with caution and do your homework.
|
||||
*
|
||||
*/
|
||||
//#define Z_MIN_PROBE_ENDSTOP
|
||||
//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
|
||||
|
||||
/**
|
||||
* Probe Type
|
||||
|
@ -793,11 +793,11 @@
|
||||
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
/**
|
||||
* Z_MIN_PROBE_ENDSTOP
|
||||
* Z_MIN_PROBE_PIN
|
||||
*
|
||||
* Enable this option for a probe connected to any pin except Z-Min.
|
||||
* (By default Marlin assumes the Z-Max endstop pin.)
|
||||
* To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
|
||||
* Define this pin if the probe is not connected to Z_MIN_PIN.
|
||||
* If not defined the default pin for the selected MOTHERBOARD
|
||||
* will be used. Most of the time the default is what you want.
|
||||
*
|
||||
* - The simplest option is to use a free endstop connector.
|
||||
* - Use 5V for powered (usually inductive) sensors.
|
||||
@ -807,11 +807,8 @@
|
||||
* - normally-closed switches to GND and D32.
|
||||
* - normally-open switches to 5V and D32.
|
||||
*
|
||||
* WARNING: Setting the wrong pin may have unexpected and potentially
|
||||
* disastrous consequences. Use with caution and do your homework.
|
||||
*
|
||||
*/
|
||||
//#define Z_MIN_PROBE_ENDSTOP
|
||||
//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
|
||||
|
||||
/**
|
||||
* Probe Type
|
||||
|
@ -780,11 +780,11 @@
|
||||
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
/**
|
||||
* Z_MIN_PROBE_ENDSTOP
|
||||
* Z_MIN_PROBE_PIN
|
||||
*
|
||||
* Enable this option for a probe connected to any pin except Z-Min.
|
||||
* (By default Marlin assumes the Z-Max endstop pin.)
|
||||
* To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
|
||||
* Define this pin if the probe is not connected to Z_MIN_PIN.
|
||||
* If not defined the default pin for the selected MOTHERBOARD
|
||||
* will be used. Most of the time the default is what you want.
|
||||
*
|
||||
* - The simplest option is to use a free endstop connector.
|
||||
* - Use 5V for powered (usually inductive) sensors.
|
||||
@ -794,11 +794,8 @@
|
||||
* - normally-closed switches to GND and D32.
|
||||
* - normally-open switches to 5V and D32.
|
||||
*
|
||||
* WARNING: Setting the wrong pin may have unexpected and potentially
|
||||
* disastrous consequences. Use with caution and do your homework.
|
||||
*
|
||||
*/
|
||||
//#define Z_MIN_PROBE_ENDSTOP
|
||||
//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
|
||||
|
||||
/**
|
||||
* Probe Type
|
||||
|
@ -747,11 +747,11 @@
|
||||
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
/**
|
||||
* Z_MIN_PROBE_ENDSTOP
|
||||
* Z_MIN_PROBE_PIN
|
||||
*
|
||||
* Enable this option for a probe connected to any pin except Z-Min.
|
||||
* (By default Marlin assumes the Z-Max endstop pin.)
|
||||
* To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
|
||||
* Define this pin if the probe is not connected to Z_MIN_PIN.
|
||||
* If not defined the default pin for the selected MOTHERBOARD
|
||||
* will be used. Most of the time the default is what you want.
|
||||
*
|
||||
* - The simplest option is to use a free endstop connector.
|
||||
* - Use 5V for powered (usually inductive) sensors.
|
||||
@ -761,11 +761,8 @@
|
||||
* - normally-closed switches to GND and D32.
|
||||
* - normally-open switches to 5V and D32.
|
||||
*
|
||||
* WARNING: Setting the wrong pin may have unexpected and potentially
|
||||
* disastrous consequences. Use with caution and do your homework.
|
||||
*
|
||||
*/
|
||||
//#define Z_MIN_PROBE_ENDSTOP
|
||||
//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
|
||||
|
||||
/**
|
||||
* Probe Type
|
||||
|
@ -747,11 +747,11 @@
|
||||
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
/**
|
||||
* Z_MIN_PROBE_ENDSTOP
|
||||
* Z_MIN_PROBE_PIN
|
||||
*
|
||||
* Enable this option for a probe connected to any pin except Z-Min.
|
||||
* (By default Marlin assumes the Z-Max endstop pin.)
|
||||
* To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
|
||||
* Define this pin if the probe is not connected to Z_MIN_PIN.
|
||||
* If not defined the default pin for the selected MOTHERBOARD
|
||||
* will be used. Most of the time the default is what you want.
|
||||
*
|
||||
* - The simplest option is to use a free endstop connector.
|
||||
* - Use 5V for powered (usually inductive) sensors.
|
||||
@ -761,11 +761,8 @@
|
||||
* - normally-closed switches to GND and D32.
|
||||
* - normally-open switches to 5V and D32.
|
||||
*
|
||||
* WARNING: Setting the wrong pin may have unexpected and potentially
|
||||
* disastrous consequences. Use with caution and do your homework.
|
||||
*
|
||||
*/
|
||||
//#define Z_MIN_PROBE_ENDSTOP
|
||||
//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
|
||||
|
||||
/**
|
||||
* Probe Type
|
||||
|
@ -779,11 +779,11 @@
|
||||
//#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
/**
|
||||
* Z_MIN_PROBE_ENDSTOP
|
||||
* Z_MIN_PROBE_PIN
|
||||
*
|
||||
* Enable this option for a probe connected to any pin except Z-Min.
|
||||
* (By default Marlin assumes the Z-Max endstop pin.)
|
||||
* To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
|
||||
* Define this pin if the probe is not connected to Z_MIN_PIN.
|
||||
* If not defined the default pin for the selected MOTHERBOARD
|
||||
* will be used. Most of the time the default is what you want.
|
||||
*
|
||||
* - The simplest option is to use a free endstop connector.
|
||||
* - Use 5V for powered (usually inductive) sensors.
|
||||
@ -793,11 +793,8 @@
|
||||
* - normally-closed switches to GND and D32.
|
||||
* - normally-open switches to 5V and D32.
|
||||
*
|
||||
* WARNING: Setting the wrong pin may have unexpected and potentially
|
||||
* disastrous consequences. Use with caution and do your homework.
|
||||
*
|
||||
*/
|
||||
//#define Z_MIN_PROBE_ENDSTOP
|
||||
//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
|
||||
|
||||
/**
|
||||
* Probe Type
|
||||
|
@ -764,11 +764,11 @@
|
||||
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
/**
|
||||
* Z_MIN_PROBE_ENDSTOP
|
||||
* Z_MIN_PROBE_PIN
|
||||
*
|
||||
* Enable this option for a probe connected to any pin except Z-Min.
|
||||
* (By default Marlin assumes the Z-Max endstop pin.)
|
||||
* To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
|
||||
* Define this pin if the probe is not connected to Z_MIN_PIN.
|
||||
* If not defined the default pin for the selected MOTHERBOARD
|
||||
* will be used. Most of the time the default is what you want.
|
||||
*
|
||||
* - The simplest option is to use a free endstop connector.
|
||||
* - Use 5V for powered (usually inductive) sensors.
|
||||
@ -778,11 +778,8 @@
|
||||
* - normally-closed switches to GND and D32.
|
||||
* - normally-open switches to 5V and D32.
|
||||
*
|
||||
* WARNING: Setting the wrong pin may have unexpected and potentially
|
||||
* disastrous consequences. Use with caution and do your homework.
|
||||
*
|
||||
*/
|
||||
//#define Z_MIN_PROBE_ENDSTOP
|
||||
//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
|
||||
|
||||
/**
|
||||
* Probe Type
|
||||
|
@ -771,11 +771,11 @@
|
||||
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
/**
|
||||
* Z_MIN_PROBE_ENDSTOP
|
||||
* Z_MIN_PROBE_PIN
|
||||
*
|
||||
* Enable this option for a probe connected to any pin except Z-Min.
|
||||
* (By default Marlin assumes the Z-Max endstop pin.)
|
||||
* To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
|
||||
* Define this pin if the probe is not connected to Z_MIN_PIN.
|
||||
* If not defined the default pin for the selected MOTHERBOARD
|
||||
* will be used. Most of the time the default is what you want.
|
||||
*
|
||||
* - The simplest option is to use a free endstop connector.
|
||||
* - Use 5V for powered (usually inductive) sensors.
|
||||
@ -785,11 +785,8 @@
|
||||
* - normally-closed switches to GND and D32.
|
||||
* - normally-open switches to 5V and D32.
|
||||
*
|
||||
* WARNING: Setting the wrong pin may have unexpected and potentially
|
||||
* disastrous consequences. Use with caution and do your homework.
|
||||
*
|
||||
*/
|
||||
//#define Z_MIN_PROBE_ENDSTOP
|
||||
//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
|
||||
|
||||
/**
|
||||
* Probe Type
|
||||
|
@ -779,11 +779,11 @@
|
||||
//#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
/**
|
||||
* Z_MIN_PROBE_ENDSTOP
|
||||
* Z_MIN_PROBE_PIN
|
||||
*
|
||||
* Enable this option for a probe connected to any pin except Z-Min.
|
||||
* (By default Marlin assumes the Z-Max endstop pin.)
|
||||
* To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
|
||||
* Define this pin if the probe is not connected to Z_MIN_PIN.
|
||||
* If not defined the default pin for the selected MOTHERBOARD
|
||||
* will be used. Most of the time the default is what you want.
|
||||
*
|
||||
* - The simplest option is to use a free endstop connector.
|
||||
* - Use 5V for powered (usually inductive) sensors.
|
||||
@ -793,11 +793,8 @@
|
||||
* - normally-closed switches to GND and D32.
|
||||
* - normally-open switches to 5V and D32.
|
||||
*
|
||||
* WARNING: Setting the wrong pin may have unexpected and potentially
|
||||
* disastrous consequences. Use with caution and do your homework.
|
||||
*
|
||||
*/
|
||||
#define Z_MIN_PROBE_ENDSTOP
|
||||
//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
|
||||
#define Z_MIN_PROBE_PIN 32
|
||||
|
||||
/**
|
||||
|
@ -779,11 +779,11 @@
|
||||
//#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
/**
|
||||
* Z_MIN_PROBE_ENDSTOP
|
||||
* Z_MIN_PROBE_PIN
|
||||
*
|
||||
* Enable this option for a probe connected to any pin except Z-Min.
|
||||
* (By default Marlin assumes the Z-Max endstop pin.)
|
||||
* To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
|
||||
* Define this pin if the probe is not connected to Z_MIN_PIN.
|
||||
* If not defined the default pin for the selected MOTHERBOARD
|
||||
* will be used. Most of the time the default is what you want.
|
||||
*
|
||||
* - The simplest option is to use a free endstop connector.
|
||||
* - Use 5V for powered (usually inductive) sensors.
|
||||
@ -793,11 +793,8 @@
|
||||
* - normally-closed switches to GND and D32.
|
||||
* - normally-open switches to 5V and D32.
|
||||
*
|
||||
* WARNING: Setting the wrong pin may have unexpected and potentially
|
||||
* disastrous consequences. Use with caution and do your homework.
|
||||
*
|
||||
*/
|
||||
//#define Z_MIN_PROBE_ENDSTOP
|
||||
//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
|
||||
|
||||
/**
|
||||
* Probe Type
|
||||
|
@ -764,11 +764,11 @@
|
||||
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
/**
|
||||
* Z_MIN_PROBE_ENDSTOP
|
||||
* Z_MIN_PROBE_PIN
|
||||
*
|
||||
* Enable this option for a probe connected to any pin except Z-Min.
|
||||
* (By default Marlin assumes the Z-Max endstop pin.)
|
||||
* To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
|
||||
* Define this pin if the probe is not connected to Z_MIN_PIN.
|
||||
* If not defined the default pin for the selected MOTHERBOARD
|
||||
* will be used. Most of the time the default is what you want.
|
||||
*
|
||||
* - The simplest option is to use a free endstop connector.
|
||||
* - Use 5V for powered (usually inductive) sensors.
|
||||
@ -778,11 +778,8 @@
|
||||
* - normally-closed switches to GND and D32.
|
||||
* - normally-open switches to 5V and D32.
|
||||
*
|
||||
* WARNING: Setting the wrong pin may have unexpected and potentially
|
||||
* disastrous consequences. Use with caution and do your homework.
|
||||
*
|
||||
*/
|
||||
//#define Z_MIN_PROBE_ENDSTOP
|
||||
//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
|
||||
|
||||
/**
|
||||
* Probe Type
|
||||
|
@ -764,11 +764,11 @@
|
||||
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
/**
|
||||
* Z_MIN_PROBE_ENDSTOP
|
||||
* Z_MIN_PROBE_PIN
|
||||
*
|
||||
* Enable this option for a probe connected to any pin except Z-Min.
|
||||
* (By default Marlin assumes the Z-Max endstop pin.)
|
||||
* To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
|
||||
* Define this pin if the probe is not connected to Z_MIN_PIN.
|
||||
* If not defined the default pin for the selected MOTHERBOARD
|
||||
* will be used. Most of the time the default is what you want.
|
||||
*
|
||||
* - The simplest option is to use a free endstop connector.
|
||||
* - Use 5V for powered (usually inductive) sensors.
|
||||
@ -778,11 +778,8 @@
|
||||
* - normally-closed switches to GND and D32.
|
||||
* - normally-open switches to 5V and D32.
|
||||
*
|
||||
* WARNING: Setting the wrong pin may have unexpected and potentially
|
||||
* disastrous consequences. Use with caution and do your homework.
|
||||
*
|
||||
*/
|
||||
//#define Z_MIN_PROBE_ENDSTOP
|
||||
//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
|
||||
|
||||
/**
|
||||
* Probe Type
|
||||
|
@ -768,11 +768,11 @@
|
||||
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
/**
|
||||
* Z_MIN_PROBE_ENDSTOP
|
||||
* Z_MIN_PROBE_PIN
|
||||
*
|
||||
* Enable this option for a probe connected to any pin except Z-Min.
|
||||
* (By default Marlin assumes the Z-Max endstop pin.)
|
||||
* To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
|
||||
* Define this pin if the probe is not connected to Z_MIN_PIN.
|
||||
* If not defined the default pin for the selected MOTHERBOARD
|
||||
* will be used. Most of the time the default is what you want.
|
||||
*
|
||||
* - The simplest option is to use a free endstop connector.
|
||||
* - Use 5V for powered (usually inductive) sensors.
|
||||
@ -782,11 +782,8 @@
|
||||
* - normally-closed switches to GND and D32.
|
||||
* - normally-open switches to 5V and D32.
|
||||
*
|
||||
* WARNING: Setting the wrong pin may have unexpected and potentially
|
||||
* disastrous consequences. Use with caution and do your homework.
|
||||
*
|
||||
*/
|
||||
//#define Z_MIN_PROBE_ENDSTOP
|
||||
//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
|
||||
|
||||
/**
|
||||
* Probe Type
|
||||
|
@ -776,11 +776,11 @@
|
||||
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
/**
|
||||
* Z_MIN_PROBE_ENDSTOP
|
||||
* Z_MIN_PROBE_PIN
|
||||
*
|
||||
* Enable this option for a probe connected to any pin except Z-Min.
|
||||
* (By default Marlin assumes the Z-Max endstop pin.)
|
||||
* To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
|
||||
* Define this pin if the probe is not connected to Z_MIN_PIN.
|
||||
* If not defined the default pin for the selected MOTHERBOARD
|
||||
* will be used. Most of the time the default is what you want.
|
||||
*
|
||||
* - The simplest option is to use a free endstop connector.
|
||||
* - Use 5V for powered (usually inductive) sensors.
|
||||
@ -790,11 +790,8 @@
|
||||
* - normally-closed switches to GND and D32.
|
||||
* - normally-open switches to 5V and D32.
|
||||
*
|
||||
* WARNING: Setting the wrong pin may have unexpected and potentially
|
||||
* disastrous consequences. Use with caution and do your homework.
|
||||
*
|
||||
*/
|
||||
//#define Z_MIN_PROBE_ENDSTOP
|
||||
//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
|
||||
|
||||
/**
|
||||
* Probe Type
|
||||
|
@ -784,11 +784,11 @@
|
||||
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
/**
|
||||
* Z_MIN_PROBE_ENDSTOP
|
||||
* Z_MIN_PROBE_PIN
|
||||
*
|
||||
* Enable this option for a probe connected to any pin except Z-Min.
|
||||
* (By default Marlin assumes the Z-Max endstop pin.)
|
||||
* To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
|
||||
* Define this pin if the probe is not connected to Z_MIN_PIN.
|
||||
* If not defined the default pin for the selected MOTHERBOARD
|
||||
* will be used. Most of the time the default is what you want.
|
||||
*
|
||||
* - The simplest option is to use a free endstop connector.
|
||||
* - Use 5V for powered (usually inductive) sensors.
|
||||
@ -798,11 +798,8 @@
|
||||
* - normally-closed switches to GND and D32.
|
||||
* - normally-open switches to 5V and D32.
|
||||
*
|
||||
* WARNING: Setting the wrong pin may have unexpected and potentially
|
||||
* disastrous consequences. Use with caution and do your homework.
|
||||
*
|
||||
*/
|
||||
//#define Z_MIN_PROBE_ENDSTOP
|
||||
//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
|
||||
|
||||
/**
|
||||
* Probe Type
|
||||
|
@ -784,11 +784,11 @@
|
||||
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
/**
|
||||
* Z_MIN_PROBE_ENDSTOP
|
||||
* Z_MIN_PROBE_PIN
|
||||
*
|
||||
* Enable this option for a probe connected to any pin except Z-Min.
|
||||
* (By default Marlin assumes the Z-Max endstop pin.)
|
||||
* To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
|
||||
* Define this pin if the probe is not connected to Z_MIN_PIN.
|
||||
* If not defined the default pin for the selected MOTHERBOARD
|
||||
* will be used. Most of the time the default is what you want.
|
||||
*
|
||||
* - The simplest option is to use a free endstop connector.
|
||||
* - Use 5V for powered (usually inductive) sensors.
|
||||
@ -798,11 +798,8 @@
|
||||
* - normally-closed switches to GND and D32.
|
||||
* - normally-open switches to 5V and D32.
|
||||
*
|
||||
* WARNING: Setting the wrong pin may have unexpected and potentially
|
||||
* disastrous consequences. Use with caution and do your homework.
|
||||
*
|
||||
*/
|
||||
//#define Z_MIN_PROBE_ENDSTOP
|
||||
//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
|
||||
|
||||
/**
|
||||
* Probe Type
|
||||
|
@ -763,11 +763,11 @@
|
||||
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
/**
|
||||
* Z_MIN_PROBE_ENDSTOP
|
||||
* Z_MIN_PROBE_PIN
|
||||
*
|
||||
* Enable this option for a probe connected to any pin except Z-Min.
|
||||
* (By default Marlin assumes the Z-Max endstop pin.)
|
||||
* To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
|
||||
* Define this pin if the probe is not connected to Z_MIN_PIN.
|
||||
* If not defined the default pin for the selected MOTHERBOARD
|
||||
* will be used. Most of the time the default is what you want.
|
||||
*
|
||||
* - The simplest option is to use a free endstop connector.
|
||||
* - Use 5V for powered (usually inductive) sensors.
|
||||
@ -777,11 +777,8 @@
|
||||
* - normally-closed switches to GND and D32.
|
||||
* - normally-open switches to 5V and D32.
|
||||
*
|
||||
* WARNING: Setting the wrong pin may have unexpected and potentially
|
||||
* disastrous consequences. Use with caution and do your homework.
|
||||
*
|
||||
*/
|
||||
//#define Z_MIN_PROBE_ENDSTOP
|
||||
//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
|
||||
|
||||
/**
|
||||
* Probe Type
|
||||
|
@ -768,11 +768,11 @@
|
||||
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
/**
|
||||
* Z_MIN_PROBE_ENDSTOP
|
||||
* Z_MIN_PROBE_PIN
|
||||
*
|
||||
* Enable this option for a probe connected to any pin except Z-Min.
|
||||
* (By default Marlin assumes the Z-Max endstop pin.)
|
||||
* To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
|
||||
* Define this pin if the probe is not connected to Z_MIN_PIN.
|
||||
* If not defined the default pin for the selected MOTHERBOARD
|
||||
* will be used. Most of the time the default is what you want.
|
||||
*
|
||||
* - The simplest option is to use a free endstop connector.
|
||||
* - Use 5V for powered (usually inductive) sensors.
|
||||
@ -782,11 +782,8 @@
|
||||
* - normally-closed switches to GND and D32.
|
||||
* - normally-open switches to 5V and D32.
|
||||
*
|
||||
* WARNING: Setting the wrong pin may have unexpected and potentially
|
||||
* disastrous consequences. Use with caution and do your homework.
|
||||
*
|
||||
*/
|
||||
//#define Z_MIN_PROBE_ENDSTOP
|
||||
//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
|
||||
|
||||
/**
|
||||
* Probe Type
|
||||
|
@ -768,11 +768,11 @@
|
||||
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
/**
|
||||
* Z_MIN_PROBE_ENDSTOP
|
||||
* Z_MIN_PROBE_PIN
|
||||
*
|
||||
* Enable this option for a probe connected to any pin except Z-Min.
|
||||
* (By default Marlin assumes the Z-Max endstop pin.)
|
||||
* To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
|
||||
* Define this pin if the probe is not connected to Z_MIN_PIN.
|
||||
* If not defined the default pin for the selected MOTHERBOARD
|
||||
* will be used. Most of the time the default is what you want.
|
||||
*
|
||||
* - The simplest option is to use a free endstop connector.
|
||||
* - Use 5V for powered (usually inductive) sensors.
|
||||
@ -782,11 +782,8 @@
|
||||
* - normally-closed switches to GND and D32.
|
||||
* - normally-open switches to 5V and D32.
|
||||
*
|
||||
* WARNING: Setting the wrong pin may have unexpected and potentially
|
||||
* disastrous consequences. Use with caution and do your homework.
|
||||
*
|
||||
*/
|
||||
//#define Z_MIN_PROBE_ENDSTOP
|
||||
//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
|
||||
|
||||
/**
|
||||
* Probe Type
|
||||
|
@ -765,11 +765,11 @@
|
||||
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
/**
|
||||
* Z_MIN_PROBE_ENDSTOP
|
||||
* Z_MIN_PROBE_PIN
|
||||
*
|
||||
* Enable this option for a probe connected to any pin except Z-Min.
|
||||
* (By default Marlin assumes the Z-Max endstop pin.)
|
||||
* To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
|
||||
* Define this pin if the probe is not connected to Z_MIN_PIN.
|
||||
* If not defined the default pin for the selected MOTHERBOARD
|
||||
* will be used. Most of the time the default is what you want.
|
||||
*
|
||||
* - The simplest option is to use a free endstop connector.
|
||||
* - Use 5V for powered (usually inductive) sensors.
|
||||
@ -779,11 +779,8 @@
|
||||
* - normally-closed switches to GND and D32.
|
||||
* - normally-open switches to 5V and D32.
|
||||
*
|
||||
* WARNING: Setting the wrong pin may have unexpected and potentially
|
||||
* disastrous consequences. Use with caution and do your homework.
|
||||
*
|
||||
*/
|
||||
//#define Z_MIN_PROBE_ENDSTOP
|
||||
//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
|
||||
|
||||
/**
|
||||
* Probe Type
|
||||
|
@ -764,11 +764,11 @@
|
||||
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
/**
|
||||
* Z_MIN_PROBE_ENDSTOP
|
||||
* Z_MIN_PROBE_PIN
|
||||
*
|
||||
* Enable this option for a probe connected to any pin except Z-Min.
|
||||
* (By default Marlin assumes the Z-Max endstop pin.)
|
||||
* To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
|
||||
* Define this pin if the probe is not connected to Z_MIN_PIN.
|
||||
* If not defined the default pin for the selected MOTHERBOARD
|
||||
* will be used. Most of the time the default is what you want.
|
||||
*
|
||||
* - The simplest option is to use a free endstop connector.
|
||||
* - Use 5V for powered (usually inductive) sensors.
|
||||
@ -778,11 +778,8 @@
|
||||
* - normally-closed switches to GND and D32.
|
||||
* - normally-open switches to 5V and D32.
|
||||
*
|
||||
* WARNING: Setting the wrong pin may have unexpected and potentially
|
||||
* disastrous consequences. Use with caution and do your homework.
|
||||
*
|
||||
*/
|
||||
//#define Z_MIN_PROBE_ENDSTOP
|
||||
//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
|
||||
|
||||
/**
|
||||
* Probe Type
|
||||
|
@ -772,11 +772,11 @@
|
||||
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
/**
|
||||
* Z_MIN_PROBE_ENDSTOP
|
||||
* Z_MIN_PROBE_PIN
|
||||
*
|
||||
* Enable this option for a probe connected to any pin except Z-Min.
|
||||
* (By default Marlin assumes the Z-Max endstop pin.)
|
||||
* To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
|
||||
* Define this pin if the probe is not connected to Z_MIN_PIN.
|
||||
* If not defined the default pin for the selected MOTHERBOARD
|
||||
* will be used. Most of the time the default is what you want.
|
||||
*
|
||||
* - The simplest option is to use a free endstop connector.
|
||||
* - Use 5V for powered (usually inductive) sensors.
|
||||
@ -786,11 +786,8 @@
|
||||
* - normally-closed switches to GND and D32.
|
||||
* - normally-open switches to 5V and D32.
|
||||
*
|
||||
* WARNING: Setting the wrong pin may have unexpected and potentially
|
||||
* disastrous consequences. Use with caution and do your homework.
|
||||
*
|
||||
*/
|
||||
//#define Z_MIN_PROBE_ENDSTOP
|
||||
//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
|
||||
|
||||
/**
|
||||
* Probe Type
|
||||
|
@ -764,11 +764,11 @@
|
||||
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
/**
|
||||
* Z_MIN_PROBE_ENDSTOP
|
||||
* Z_MIN_PROBE_PIN
|
||||
*
|
||||
* Enable this option for a probe connected to any pin except Z-Min.
|
||||
* (By default Marlin assumes the Z-Max endstop pin.)
|
||||
* To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
|
||||
* Define this pin if the probe is not connected to Z_MIN_PIN.
|
||||
* If not defined the default pin for the selected MOTHERBOARD
|
||||
* will be used. Most of the time the default is what you want.
|
||||
*
|
||||
* - The simplest option is to use a free endstop connector.
|
||||
* - Use 5V for powered (usually inductive) sensors.
|
||||
@ -778,11 +778,8 @@
|
||||
* - normally-closed switches to GND and D32.
|
||||
* - normally-open switches to 5V and D32.
|
||||
*
|
||||
* WARNING: Setting the wrong pin may have unexpected and potentially
|
||||
* disastrous consequences. Use with caution and do your homework.
|
||||
*
|
||||
*/
|
||||
//#define Z_MIN_PROBE_ENDSTOP
|
||||
//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
|
||||
|
||||
/**
|
||||
* Probe Type
|
||||
|
@ -804,11 +804,11 @@ Black rubber belt(MXL), 18 - tooth aluminium pulley : 87.489 step per mm (Huxley
|
||||
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
/**
|
||||
* Z_MIN_PROBE_ENDSTOP
|
||||
* Z_MIN_PROBE_PIN
|
||||
*
|
||||
* Enable this option for a probe connected to any pin except Z-Min.
|
||||
* (By default Marlin assumes the Z-Max endstop pin.)
|
||||
* To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
|
||||
* Define this pin if the probe is not connected to Z_MIN_PIN.
|
||||
* If not defined the default pin for the selected MOTHERBOARD
|
||||
* will be used. Most of the time the default is what you want.
|
||||
*
|
||||
* - The simplest option is to use a free endstop connector.
|
||||
* - Use 5V for powered (usually inductive) sensors.
|
||||
@ -818,11 +818,8 @@ Black rubber belt(MXL), 18 - tooth aluminium pulley : 87.489 step per mm (Huxley
|
||||
* - normally-closed switches to GND and D32.
|
||||
* - normally-open switches to 5V and D32.
|
||||
*
|
||||
* WARNING: Setting the wrong pin may have unexpected and potentially
|
||||
* disastrous consequences. Use with caution and do your homework.
|
||||
*
|
||||
*/
|
||||
//#define Z_MIN_PROBE_ENDSTOP
|
||||
//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
|
||||
|
||||
/**
|
||||
* Probe Type
|
||||
|
@ -764,11 +764,11 @@
|
||||
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
/**
|
||||
* Z_MIN_PROBE_ENDSTOP
|
||||
* Z_MIN_PROBE_PIN
|
||||
*
|
||||
* Enable this option for a probe connected to any pin except Z-Min.
|
||||
* (By default Marlin assumes the Z-Max endstop pin.)
|
||||
* To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
|
||||
* Define this pin if the probe is not connected to Z_MIN_PIN.
|
||||
* If not defined the default pin for the selected MOTHERBOARD
|
||||
* will be used. Most of the time the default is what you want.
|
||||
*
|
||||
* - The simplest option is to use a free endstop connector.
|
||||
* - Use 5V for powered (usually inductive) sensors.
|
||||
@ -778,11 +778,8 @@
|
||||
* - normally-closed switches to GND and D32.
|
||||
* - normally-open switches to 5V and D32.
|
||||
*
|
||||
* WARNING: Setting the wrong pin may have unexpected and potentially
|
||||
* disastrous consequences. Use with caution and do your homework.
|
||||
*
|
||||
*/
|
||||
//#define Z_MIN_PROBE_ENDSTOP
|
||||
//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
|
||||
|
||||
/**
|
||||
* Probe Type
|
||||
|
@ -762,11 +762,11 @@
|
||||
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
/**
|
||||
* Z_MIN_PROBE_ENDSTOP
|
||||
* Z_MIN_PROBE_PIN
|
||||
*
|
||||
* Enable this option for a probe connected to any pin except Z-Min.
|
||||
* (By default Marlin assumes the Z-Max endstop pin.)
|
||||
* To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
|
||||
* Define this pin if the probe is not connected to Z_MIN_PIN.
|
||||
* If not defined the default pin for the selected MOTHERBOARD
|
||||
* will be used. Most of the time the default is what you want.
|
||||
*
|
||||
* - The simplest option is to use a free endstop connector.
|
||||
* - Use 5V for powered (usually inductive) sensors.
|
||||
@ -776,11 +776,8 @@
|
||||
* - normally-closed switches to GND and D32.
|
||||
* - normally-open switches to 5V and D32.
|
||||
*
|
||||
* WARNING: Setting the wrong pin may have unexpected and potentially
|
||||
* disastrous consequences. Use with caution and do your homework.
|
||||
*
|
||||
*/
|
||||
//#define Z_MIN_PROBE_ENDSTOP
|
||||
//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
|
||||
|
||||
/**
|
||||
* Probe Type
|
||||
|
@ -777,11 +777,11 @@
|
||||
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
/**
|
||||
* Z_MIN_PROBE_ENDSTOP
|
||||
* Z_MIN_PROBE_PIN
|
||||
*
|
||||
* Enable this option for a probe connected to any pin except Z-Min.
|
||||
* (By default Marlin assumes the Z-Max endstop pin.)
|
||||
* To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
|
||||
* Define this pin if the probe is not connected to Z_MIN_PIN.
|
||||
* If not defined the default pin for the selected MOTHERBOARD
|
||||
* will be used. Most of the time the default is what you want.
|
||||
*
|
||||
* - The simplest option is to use a free endstop connector.
|
||||
* - Use 5V for powered (usually inductive) sensors.
|
||||
@ -791,11 +791,8 @@
|
||||
* - normally-closed switches to GND and D32.
|
||||
* - normally-open switches to 5V and D32.
|
||||
*
|
||||
* WARNING: Setting the wrong pin may have unexpected and potentially
|
||||
* disastrous consequences. Use with caution and do your homework.
|
||||
*
|
||||
*/
|
||||
//#define Z_MIN_PROBE_ENDSTOP
|
||||
//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
|
||||
|
||||
/**
|
||||
* Probe Type
|
||||
|
@ -766,11 +766,11 @@
|
||||
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
/**
|
||||
* Z_MIN_PROBE_ENDSTOP
|
||||
* Z_MIN_PROBE_PIN
|
||||
*
|
||||
* Enable this option for a probe connected to any pin except Z-Min.
|
||||
* (By default Marlin assumes the Z-Max endstop pin.)
|
||||
* To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
|
||||
* Define this pin if the probe is not connected to Z_MIN_PIN.
|
||||
* If not defined the default pin for the selected MOTHERBOARD
|
||||
* will be used. Most of the time the default is what you want.
|
||||
*
|
||||
* - The simplest option is to use a free endstop connector.
|
||||
* - Use 5V for powered (usually inductive) sensors.
|
||||
@ -780,11 +780,8 @@
|
||||
* - normally-closed switches to GND and D32.
|
||||
* - normally-open switches to 5V and D32.
|
||||
*
|
||||
* WARNING: Setting the wrong pin may have unexpected and potentially
|
||||
* disastrous consequences. Use with caution and do your homework.
|
||||
*
|
||||
*/
|
||||
//#define Z_MIN_PROBE_ENDSTOP
|
||||
//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
|
||||
|
||||
/**
|
||||
* Probe Type
|
||||
|
@ -764,11 +764,11 @@
|
||||
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
/**
|
||||
* Z_MIN_PROBE_ENDSTOP
|
||||
* Z_MIN_PROBE_PIN
|
||||
*
|
||||
* Enable this option for a probe connected to any pin except Z-Min.
|
||||
* (By default Marlin assumes the Z-Max endstop pin.)
|
||||
* To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
|
||||
* Define this pin if the probe is not connected to Z_MIN_PIN.
|
||||
* If not defined the default pin for the selected MOTHERBOARD
|
||||
* will be used. Most of the time the default is what you want.
|
||||
*
|
||||
* - The simplest option is to use a free endstop connector.
|
||||
* - Use 5V for powered (usually inductive) sensors.
|
||||
@ -778,11 +778,8 @@
|
||||
* - normally-closed switches to GND and D32.
|
||||
* - normally-open switches to 5V and D32.
|
||||
*
|
||||
* WARNING: Setting the wrong pin may have unexpected and potentially
|
||||
* disastrous consequences. Use with caution and do your homework.
|
||||
*
|
||||
*/
|
||||
//#define Z_MIN_PROBE_ENDSTOP
|
||||
//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
|
||||
|
||||
/**
|
||||
* Probe Type
|
||||
|
@ -795,11 +795,11 @@
|
||||
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
/**
|
||||
* Z_MIN_PROBE_ENDSTOP
|
||||
* Z_MIN_PROBE_PIN
|
||||
*
|
||||
* Enable this option for a probe connected to any pin except Z-Min.
|
||||
* (By default Marlin assumes the Z-Max endstop pin.)
|
||||
* To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
|
||||
* Define this pin if the probe is not connected to Z_MIN_PIN.
|
||||
* If not defined the default pin for the selected MOTHERBOARD
|
||||
* will be used. Most of the time the default is what you want.
|
||||
*
|
||||
* - The simplest option is to use a free endstop connector.
|
||||
* - Use 5V for powered (usually inductive) sensors.
|
||||
@ -809,11 +809,8 @@
|
||||
* - normally-closed switches to GND and D32.
|
||||
* - normally-open switches to 5V and D32.
|
||||
*
|
||||
* WARNING: Setting the wrong pin may have unexpected and potentially
|
||||
* disastrous consequences. Use with caution and do your homework.
|
||||
*
|
||||
*/
|
||||
//#define Z_MIN_PROBE_ENDSTOP
|
||||
//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
|
||||
|
||||
/**
|
||||
* Probe Type
|
||||
|
@ -764,11 +764,11 @@
|
||||
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
/**
|
||||
* Z_MIN_PROBE_ENDSTOP
|
||||
* Z_MIN_PROBE_PIN
|
||||
*
|
||||
* Enable this option for a probe connected to any pin except Z-Min.
|
||||
* (By default Marlin assumes the Z-Max endstop pin.)
|
||||
* To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
|
||||
* Define this pin if the probe is not connected to Z_MIN_PIN.
|
||||
* If not defined the default pin for the selected MOTHERBOARD
|
||||
* will be used. Most of the time the default is what you want.
|
||||
*
|
||||
* - The simplest option is to use a free endstop connector.
|
||||
* - Use 5V for powered (usually inductive) sensors.
|
||||
@ -778,11 +778,8 @@
|
||||
* - normally-closed switches to GND and D32.
|
||||
* - normally-open switches to 5V and D32.
|
||||
*
|
||||
* WARNING: Setting the wrong pin may have unexpected and potentially
|
||||
* disastrous consequences. Use with caution and do your homework.
|
||||
*
|
||||
*/
|
||||
//#define Z_MIN_PROBE_ENDSTOP
|
||||
//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
|
||||
|
||||
/**
|
||||
* Probe Type
|
||||
|
@ -815,11 +815,11 @@
|
||||
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
/**
|
||||
* Z_MIN_PROBE_ENDSTOP
|
||||
* Z_MIN_PROBE_PIN
|
||||
*
|
||||
* Enable this option for a probe connected to any pin except Z-Min.
|
||||
* (By default Marlin assumes the Z-Max endstop pin.)
|
||||
* To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
|
||||
* Define this pin if the probe is not connected to Z_MIN_PIN.
|
||||
* If not defined the default pin for the selected MOTHERBOARD
|
||||
* will be used. Most of the time the default is what you want.
|
||||
*
|
||||
* - The simplest option is to use a free endstop connector.
|
||||
* - Use 5V for powered (usually inductive) sensors.
|
||||
@ -829,11 +829,8 @@
|
||||
* - normally-closed switches to GND and D32.
|
||||
* - normally-open switches to 5V and D32.
|
||||
*
|
||||
* WARNING: Setting the wrong pin may have unexpected and potentially
|
||||
* disastrous consequences. Use with caution and do your homework.
|
||||
*
|
||||
*/
|
||||
//#define Z_MIN_PROBE_ENDSTOP
|
||||
//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
|
||||
|
||||
/**
|
||||
* Probe Type
|
||||
|
@ -764,11 +764,11 @@
|
||||
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
/**
|
||||
* Z_MIN_PROBE_ENDSTOP
|
||||
* Z_MIN_PROBE_PIN
|
||||
*
|
||||
* Enable this option for a probe connected to any pin except Z-Min.
|
||||
* (By default Marlin assumes the Z-Max endstop pin.)
|
||||
* To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
|
||||
* Define this pin if the probe is not connected to Z_MIN_PIN.
|
||||
* If not defined the default pin for the selected MOTHERBOARD
|
||||
* will be used. Most of the time the default is what you want.
|
||||
*
|
||||
* - The simplest option is to use a free endstop connector.
|
||||
* - Use 5V for powered (usually inductive) sensors.
|
||||
@ -778,11 +778,8 @@
|
||||
* - normally-closed switches to GND and D32.
|
||||
* - normally-open switches to 5V and D32.
|
||||
*
|
||||
* WARNING: Setting the wrong pin may have unexpected and potentially
|
||||
* disastrous consequences. Use with caution and do your homework.
|
||||
*
|
||||
*/
|
||||
//#define Z_MIN_PROBE_ENDSTOP
|
||||
//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
|
||||
|
||||
/**
|
||||
* Probe Type
|
||||
|
@ -764,11 +764,11 @@
|
||||
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
/**
|
||||
* Z_MIN_PROBE_ENDSTOP
|
||||
* Z_MIN_PROBE_PIN
|
||||
*
|
||||
* Enable this option for a probe connected to any pin except Z-Min.
|
||||
* (By default Marlin assumes the Z-Max endstop pin.)
|
||||
* To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
|
||||
* Define this pin if the probe is not connected to Z_MIN_PIN.
|
||||
* If not defined the default pin for the selected MOTHERBOARD
|
||||
* will be used. Most of the time the default is what you want.
|
||||
*
|
||||
* - The simplest option is to use a free endstop connector.
|
||||
* - Use 5V for powered (usually inductive) sensors.
|
||||
@ -778,11 +778,8 @@
|
||||
* - normally-closed switches to GND and D32.
|
||||
* - normally-open switches to 5V and D32.
|
||||
*
|
||||
* WARNING: Setting the wrong pin may have unexpected and potentially
|
||||
* disastrous consequences. Use with caution and do your homework.
|
||||
*
|
||||
*/
|
||||
//#define Z_MIN_PROBE_ENDSTOP
|
||||
//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
|
||||
|
||||
/**
|
||||
* Probe Type
|
||||
|
@ -763,11 +763,11 @@
|
||||
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
/**
|
||||
* Z_MIN_PROBE_ENDSTOP
|
||||
* Z_MIN_PROBE_PIN
|
||||
*
|
||||
* Enable this option for a probe connected to any pin except Z-Min.
|
||||
* (By default Marlin assumes the Z-Max endstop pin.)
|
||||
* To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
|
||||
* Define this pin if the probe is not connected to Z_MIN_PIN.
|
||||
* If not defined the default pin for the selected MOTHERBOARD
|
||||
* will be used. Most of the time the default is what you want.
|
||||
*
|
||||
* - The simplest option is to use a free endstop connector.
|
||||
* - Use 5V for powered (usually inductive) sensors.
|
||||
@ -777,11 +777,8 @@
|
||||
* - normally-closed switches to GND and D32.
|
||||
* - normally-open switches to 5V and D32.
|
||||
*
|
||||
* WARNING: Setting the wrong pin may have unexpected and potentially
|
||||
* disastrous consequences. Use with caution and do your homework.
|
||||
*
|
||||
*/
|
||||
//#define Z_MIN_PROBE_ENDSTOP
|
||||
//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
|
||||
|
||||
/**
|
||||
* Probe Type
|
||||
|
@ -775,11 +775,11 @@
|
||||
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
/**
|
||||
* Z_MIN_PROBE_ENDSTOP
|
||||
* Z_MIN_PROBE_PIN
|
||||
*
|
||||
* Enable this option for a probe connected to any pin except Z-Min.
|
||||
* (By default Marlin assumes the Z-Max endstop pin.)
|
||||
* To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
|
||||
* Define this pin if the probe is not connected to Z_MIN_PIN.
|
||||
* If not defined the default pin for the selected MOTHERBOARD
|
||||
* will be used. Most of the time the default is what you want.
|
||||
*
|
||||
* - The simplest option is to use a free endstop connector.
|
||||
* - Use 5V for powered (usually inductive) sensors.
|
||||
@ -789,11 +789,8 @@
|
||||
* - normally-closed switches to GND and D32.
|
||||
* - normally-open switches to 5V and D32.
|
||||
*
|
||||
* WARNING: Setting the wrong pin may have unexpected and potentially
|
||||
* disastrous consequences. Use with caution and do your homework.
|
||||
*
|
||||
*/
|
||||
//#define Z_MIN_PROBE_ENDSTOP
|
||||
//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
|
||||
|
||||
/**
|
||||
* Probe Type
|
||||
|
@ -764,11 +764,11 @@
|
||||
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
/**
|
||||
* Z_MIN_PROBE_ENDSTOP
|
||||
* Z_MIN_PROBE_PIN
|
||||
*
|
||||
* Enable this option for a probe connected to any pin except Z-Min.
|
||||
* (By default Marlin assumes the Z-Max endstop pin.)
|
||||
* To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
|
||||
* Define this pin if the probe is not connected to Z_MIN_PIN.
|
||||
* If not defined the default pin for the selected MOTHERBOARD
|
||||
* will be used. Most of the time the default is what you want.
|
||||
*
|
||||
* - The simplest option is to use a free endstop connector.
|
||||
* - Use 5V for powered (usually inductive) sensors.
|
||||
@ -778,11 +778,8 @@
|
||||
* - normally-closed switches to GND and D32.
|
||||
* - normally-open switches to 5V and D32.
|
||||
*
|
||||
* WARNING: Setting the wrong pin may have unexpected and potentially
|
||||
* disastrous consequences. Use with caution and do your homework.
|
||||
*
|
||||
*/
|
||||
//#define Z_MIN_PROBE_ENDSTOP
|
||||
//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
|
||||
|
||||
/**
|
||||
* Probe Type
|
||||
|
@ -764,11 +764,11 @@
|
||||
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
/**
|
||||
* Z_MIN_PROBE_ENDSTOP
|
||||
* Z_MIN_PROBE_PIN
|
||||
*
|
||||
* Enable this option for a probe connected to any pin except Z-Min.
|
||||
* (By default Marlin assumes the Z-Max endstop pin.)
|
||||
* To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
|
||||
* Define this pin if the probe is not connected to Z_MIN_PIN.
|
||||
* If not defined the default pin for the selected MOTHERBOARD
|
||||
* will be used. Most of the time the default is what you want.
|
||||
*
|
||||
* - The simplest option is to use a free endstop connector.
|
||||
* - Use 5V for powered (usually inductive) sensors.
|
||||
@ -778,11 +778,8 @@
|
||||
* - normally-closed switches to GND and D32.
|
||||
* - normally-open switches to 5V and D32.
|
||||
*
|
||||
* WARNING: Setting the wrong pin may have unexpected and potentially
|
||||
* disastrous consequences. Use with caution and do your homework.
|
||||
*
|
||||
*/
|
||||
//#define Z_MIN_PROBE_ENDSTOP
|
||||
//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
|
||||
|
||||
/**
|
||||
* Probe Type
|
||||
|
@ -773,11 +773,11 @@
|
||||
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
/**
|
||||
* Z_MIN_PROBE_ENDSTOP
|
||||
* Z_MIN_PROBE_PIN
|
||||
*
|
||||
* Enable this option for a probe connected to any pin except Z-Min.
|
||||
* (By default Marlin assumes the Z-Max endstop pin.)
|
||||
* To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
|
||||
* Define this pin if the probe is not connected to Z_MIN_PIN.
|
||||
* If not defined the default pin for the selected MOTHERBOARD
|
||||
* will be used. Most of the time the default is what you want.
|
||||
*
|
||||
* - The simplest option is to use a free endstop connector.
|
||||
* - Use 5V for powered (usually inductive) sensors.
|
||||
@ -787,11 +787,8 @@
|
||||
* - normally-closed switches to GND and D32.
|
||||
* - normally-open switches to 5V and D32.
|
||||
*
|
||||
* WARNING: Setting the wrong pin may have unexpected and potentially
|
||||
* disastrous consequences. Use with caution and do your homework.
|
||||
*
|
||||
*/
|
||||
//#define Z_MIN_PROBE_ENDSTOP
|
||||
//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
|
||||
|
||||
/**
|
||||
* Probe Type
|
||||
|
@ -793,11 +793,11 @@
|
||||
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
/**
|
||||
* Z_MIN_PROBE_ENDSTOP
|
||||
* Z_MIN_PROBE_PIN
|
||||
*
|
||||
* Enable this option for a probe connected to any pin except Z-Min.
|
||||
* (By default Marlin assumes the Z-Max endstop pin.)
|
||||
* To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
|
||||
* Define this pin if the probe is not connected to Z_MIN_PIN.
|
||||
* If not defined the default pin for the selected MOTHERBOARD
|
||||
* will be used. Most of the time the default is what you want.
|
||||
*
|
||||
* - The simplest option is to use a free endstop connector.
|
||||
* - Use 5V for powered (usually inductive) sensors.
|
||||
@ -807,11 +807,8 @@
|
||||
* - normally-closed switches to GND and D32.
|
||||
* - normally-open switches to 5V and D32.
|
||||
*
|
||||
* WARNING: Setting the wrong pin may have unexpected and potentially
|
||||
* disastrous consequences. Use with caution and do your homework.
|
||||
*
|
||||
*/
|
||||
//#define Z_MIN_PROBE_ENDSTOP
|
||||
//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
|
||||
|
||||
/**
|
||||
* Probe Type
|
||||
|
@ -764,11 +764,11 @@
|
||||
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
/**
|
||||
* Z_MIN_PROBE_ENDSTOP
|
||||
* Z_MIN_PROBE_PIN
|
||||
*
|
||||
* Enable this option for a probe connected to any pin except Z-Min.
|
||||
* (By default Marlin assumes the Z-Max endstop pin.)
|
||||
* To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
|
||||
* Define this pin if the probe is not connected to Z_MIN_PIN.
|
||||
* If not defined the default pin for the selected MOTHERBOARD
|
||||
* will be used. Most of the time the default is what you want.
|
||||
*
|
||||
* - The simplest option is to use a free endstop connector.
|
||||
* - Use 5V for powered (usually inductive) sensors.
|
||||
@ -778,11 +778,8 @@
|
||||
* - normally-closed switches to GND and D32.
|
||||
* - normally-open switches to 5V and D32.
|
||||
*
|
||||
* WARNING: Setting the wrong pin may have unexpected and potentially
|
||||
* disastrous consequences. Use with caution and do your homework.
|
||||
*
|
||||
*/
|
||||
//#define Z_MIN_PROBE_ENDSTOP
|
||||
//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
|
||||
|
||||
/**
|
||||
* Probe Type
|
||||
|
@ -764,11 +764,11 @@
|
||||
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
/**
|
||||
* Z_MIN_PROBE_ENDSTOP
|
||||
* Z_MIN_PROBE_PIN
|
||||
*
|
||||
* Enable this option for a probe connected to any pin except Z-Min.
|
||||
* (By default Marlin assumes the Z-Max endstop pin.)
|
||||
* To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
|
||||
* Define this pin if the probe is not connected to Z_MIN_PIN.
|
||||
* If not defined the default pin for the selected MOTHERBOARD
|
||||
* will be used. Most of the time the default is what you want.
|
||||
*
|
||||
* - The simplest option is to use a free endstop connector.
|
||||
* - Use 5V for powered (usually inductive) sensors.
|
||||
@ -778,11 +778,8 @@
|
||||
* - normally-closed switches to GND and D32.
|
||||
* - normally-open switches to 5V and D32.
|
||||
*
|
||||
* WARNING: Setting the wrong pin may have unexpected and potentially
|
||||
* disastrous consequences. Use with caution and do your homework.
|
||||
*
|
||||
*/
|
||||
//#define Z_MIN_PROBE_ENDSTOP
|
||||
//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
|
||||
|
||||
/**
|
||||
* Probe Type
|
||||
|
@ -783,11 +783,11 @@
|
||||
//#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
/**
|
||||
* Z_MIN_PROBE_ENDSTOP
|
||||
* Z_MIN_PROBE_PIN
|
||||
*
|
||||
* Enable this option for a probe connected to any pin except Z-Min.
|
||||
* (By default Marlin assumes the Z-Max endstop pin.)
|
||||
* To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
|
||||
* Define this pin if the probe is not connected to Z_MIN_PIN.
|
||||
* If not defined the default pin for the selected MOTHERBOARD
|
||||
* will be used. Most of the time the default is what you want.
|
||||
*
|
||||
* - The simplest option is to use a free endstop connector.
|
||||
* - Use 5V for powered (usually inductive) sensors.
|
||||
@ -797,11 +797,8 @@
|
||||
* - normally-closed switches to GND and D32.
|
||||
* - normally-open switches to 5V and D32.
|
||||
*
|
||||
* WARNING: Setting the wrong pin may have unexpected and potentially
|
||||
* disastrous consequences. Use with caution and do your homework.
|
||||
*
|
||||
*/
|
||||
//#define Z_MIN_PROBE_ENDSTOP
|
||||
//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
|
||||
|
||||
/**
|
||||
* Probe Type
|
||||
|
@ -774,11 +774,11 @@
|
||||
//#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
/**
|
||||
* Z_MIN_PROBE_ENDSTOP
|
||||
* Z_MIN_PROBE_PIN
|
||||
*
|
||||
* Enable this option for a probe connected to any pin except Z-Min.
|
||||
* (By default Marlin assumes the Z-Max endstop pin.)
|
||||
* To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
|
||||
* Define this pin if the probe is not connected to Z_MIN_PIN.
|
||||
* If not defined the default pin for the selected MOTHERBOARD
|
||||
* will be used. Most of the time the default is what you want.
|
||||
*
|
||||
* - The simplest option is to use a free endstop connector.
|
||||
* - Use 5V for powered (usually inductive) sensors.
|
||||
@ -788,11 +788,8 @@
|
||||
* - normally-closed switches to GND and D32.
|
||||
* - normally-open switches to 5V and D32.
|
||||
*
|
||||
* WARNING: Setting the wrong pin may have unexpected and potentially
|
||||
* disastrous consequences. Use with caution and do your homework.
|
||||
*
|
||||
*/
|
||||
//#define Z_MIN_PROBE_ENDSTOP
|
||||
//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
|
||||
|
||||
/**
|
||||
* Probe Type
|
||||
|
@ -764,11 +764,11 @@
|
||||
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
/**
|
||||
* Z_MIN_PROBE_ENDSTOP
|
||||
* Z_MIN_PROBE_PIN
|
||||
*
|
||||
* Enable this option for a probe connected to any pin except Z-Min.
|
||||
* (By default Marlin assumes the Z-Max endstop pin.)
|
||||
* To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
|
||||
* Define this pin if the probe is not connected to Z_MIN_PIN.
|
||||
* If not defined the default pin for the selected MOTHERBOARD
|
||||
* will be used. Most of the time the default is what you want.
|
||||
*
|
||||
* - The simplest option is to use a free endstop connector.
|
||||
* - Use 5V for powered (usually inductive) sensors.
|
||||
@ -778,11 +778,8 @@
|
||||
* - normally-closed switches to GND and D32.
|
||||
* - normally-open switches to 5V and D32.
|
||||
*
|
||||
* WARNING: Setting the wrong pin may have unexpected and potentially
|
||||
* disastrous consequences. Use with caution and do your homework.
|
||||
*
|
||||
*/
|
||||
//#define Z_MIN_PROBE_ENDSTOP
|
||||
//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
|
||||
|
||||
/**
|
||||
* Probe Type
|
||||
|
@ -896,11 +896,11 @@
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Z_MIN_PROBE_ENDSTOP
|
||||
* Z_MIN_PROBE_PIN
|
||||
*
|
||||
* Enable this option for a probe connected to any pin except Z-Min.
|
||||
* (By default Marlin assumes the Z-Max endstop pin.)
|
||||
* To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
|
||||
* Define this pin if the probe is not connected to Z_MIN_PIN.
|
||||
* If not defined the default pin for the selected MOTHERBOARD
|
||||
* will be used. Most of the time the default is what you want.
|
||||
*
|
||||
* - The simplest option is to use a free endstop connector.
|
||||
* - Use 5V for powered (usually inductive) sensors.
|
||||
@ -910,11 +910,8 @@
|
||||
* - normally-closed switches to GND and D32.
|
||||
* - normally-open switches to 5V and D32.
|
||||
*
|
||||
* WARNING: Setting the wrong pin may have unexpected and potentially
|
||||
* disastrous consequences. Use with caution and do your homework.
|
||||
*
|
||||
*/
|
||||
//#define Z_MIN_PROBE_ENDSTOP
|
||||
//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
|
||||
|
||||
/**
|
||||
* Probe Type
|
||||
|
@ -846,11 +846,11 @@
|
||||
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
/**
|
||||
* Z_MIN_PROBE_ENDSTOP
|
||||
* Z_MIN_PROBE_PIN
|
||||
*
|
||||
* Enable this option for a probe connected to any pin except Z-Min.
|
||||
* (By default Marlin assumes the Z-Max endstop pin.)
|
||||
* To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
|
||||
* Define this pin if the probe is not connected to Z_MIN_PIN.
|
||||
* If not defined the default pin for the selected MOTHERBOARD
|
||||
* will be used. Most of the time the default is what you want.
|
||||
*
|
||||
* - The simplest option is to use a free endstop connector.
|
||||
* - Use 5V for powered (usually inductive) sensors.
|
||||
@ -860,11 +860,8 @@
|
||||
* - normally-closed switches to GND and D32.
|
||||
* - normally-open switches to 5V and D32.
|
||||
*
|
||||
* WARNING: Setting the wrong pin may have unexpected and potentially
|
||||
* disastrous consequences. Use with caution and do your homework.
|
||||
*
|
||||
*/
|
||||
//#define Z_MIN_PROBE_ENDSTOP // A3K leave disabled!
|
||||
//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
|
||||
|
||||
/**
|
||||
* Probe Type
|
||||
|
@ -846,11 +846,11 @@
|
||||
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
/**
|
||||
* Z_MIN_PROBE_ENDSTOP
|
||||
* Z_MIN_PROBE_PIN
|
||||
*
|
||||
* Enable this option for a probe connected to any pin except Z-Min.
|
||||
* (By default Marlin assumes the Z-Max endstop pin.)
|
||||
* To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
|
||||
* Define this pin if the probe is not connected to Z_MIN_PIN.
|
||||
* If not defined the default pin for the selected MOTHERBOARD
|
||||
* will be used. Most of the time the default is what you want.
|
||||
*
|
||||
* - The simplest option is to use a free endstop connector.
|
||||
* - Use 5V for powered (usually inductive) sensors.
|
||||
@ -860,11 +860,8 @@
|
||||
* - normally-closed switches to GND and D32.
|
||||
* - normally-open switches to 5V and D32.
|
||||
*
|
||||
* WARNING: Setting the wrong pin may have unexpected and potentially
|
||||
* disastrous consequences. Use with caution and do your homework.
|
||||
*
|
||||
*/
|
||||
//#define Z_MIN_PROBE_ENDSTOP // A3K leave disabled!
|
||||
//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
|
||||
|
||||
/**
|
||||
* Probe Type
|
||||
|
@ -846,11 +846,11 @@
|
||||
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
/**
|
||||
* Z_MIN_PROBE_ENDSTOP
|
||||
* Z_MIN_PROBE_PIN
|
||||
*
|
||||
* Enable this option for a probe connected to any pin except Z-Min.
|
||||
* (By default Marlin assumes the Z-Max endstop pin.)
|
||||
* To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
|
||||
* Define this pin if the probe is not connected to Z_MIN_PIN.
|
||||
* If not defined the default pin for the selected MOTHERBOARD
|
||||
* will be used. Most of the time the default is what you want.
|
||||
*
|
||||
* - The simplest option is to use a free endstop connector.
|
||||
* - Use 5V for powered (usually inductive) sensors.
|
||||
@ -860,11 +860,8 @@
|
||||
* - normally-closed switches to GND and D32.
|
||||
* - normally-open switches to 5V and D32.
|
||||
*
|
||||
* WARNING: Setting the wrong pin may have unexpected and potentially
|
||||
* disastrous consequences. Use with caution and do your homework.
|
||||
*
|
||||
*/
|
||||
//#define Z_MIN_PROBE_ENDSTOP // A3K leave disabled!
|
||||
//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
|
||||
|
||||
/**
|
||||
* Probe Type
|
||||
|
@ -836,11 +836,11 @@
|
||||
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
/**
|
||||
* Z_MIN_PROBE_ENDSTOP
|
||||
* Z_MIN_PROBE_PIN
|
||||
*
|
||||
* Enable this option for a probe connected to any pin except Z-Min.
|
||||
* (By default Marlin assumes the Z-Max endstop pin.)
|
||||
* To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
|
||||
* Define this pin if the probe is not connected to Z_MIN_PIN.
|
||||
* If not defined the default pin for the selected MOTHERBOARD
|
||||
* will be used. Most of the time the default is what you want.
|
||||
*
|
||||
* - The simplest option is to use a free endstop connector.
|
||||
* - Use 5V for powered (usually inductive) sensors.
|
||||
@ -850,11 +850,8 @@
|
||||
* - normally-closed switches to GND and D32.
|
||||
* - normally-open switches to 5V and D32.
|
||||
*
|
||||
* WARNING: Setting the wrong pin may have unexpected and potentially
|
||||
* disastrous consequences. Use with caution and do your homework.
|
||||
*
|
||||
*/
|
||||
//#define Z_MIN_PROBE_ENDSTOP
|
||||
//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
|
||||
|
||||
/**
|
||||
* Probe Type
|
||||
|
@ -851,11 +851,11 @@
|
||||
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
/**
|
||||
* Z_MIN_PROBE_ENDSTOP
|
||||
* Z_MIN_PROBE_PIN
|
||||
*
|
||||
* Enable this option for a probe connected to any pin except Z-Min.
|
||||
* (By default Marlin assumes the Z-Max endstop pin.)
|
||||
* To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
|
||||
* Define this pin if the probe is not connected to Z_MIN_PIN.
|
||||
* If not defined the default pin for the selected MOTHERBOARD
|
||||
* will be used. Most of the time the default is what you want.
|
||||
*
|
||||
* - The simplest option is to use a free endstop connector.
|
||||
* - Use 5V for powered (usually inductive) sensors.
|
||||
@ -865,11 +865,8 @@
|
||||
* - normally-closed switches to GND and D32.
|
||||
* - normally-open switches to 5V and D32.
|
||||
*
|
||||
* WARNING: Setting the wrong pin may have unexpected and potentially
|
||||
* disastrous consequences. Use with caution and do your homework.
|
||||
*
|
||||
*/
|
||||
//#define Z_MIN_PROBE_ENDSTOP
|
||||
//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
|
||||
|
||||
/**
|
||||
* Probe Type
|
||||
|
@ -836,11 +836,11 @@
|
||||
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
/**
|
||||
* Z_MIN_PROBE_ENDSTOP
|
||||
* Z_MIN_PROBE_PIN
|
||||
*
|
||||
* Enable this option for a probe connected to any pin except Z-Min.
|
||||
* (By default Marlin assumes the Z-Max endstop pin.)
|
||||
* To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
|
||||
* Define this pin if the probe is not connected to Z_MIN_PIN.
|
||||
* If not defined the default pin for the selected MOTHERBOARD
|
||||
* will be used. Most of the time the default is what you want.
|
||||
*
|
||||
* - The simplest option is to use a free endstop connector.
|
||||
* - Use 5V for powered (usually inductive) sensors.
|
||||
@ -850,11 +850,8 @@
|
||||
* - normally-closed switches to GND and D32.
|
||||
* - normally-open switches to 5V and D32.
|
||||
*
|
||||
* WARNING: Setting the wrong pin may have unexpected and potentially
|
||||
* disastrous consequences. Use with caution and do your homework.
|
||||
*
|
||||
*/
|
||||
//#define Z_MIN_PROBE_ENDSTOP
|
||||
//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
|
||||
|
||||
/**
|
||||
* Probe Type
|
||||
|
@ -840,11 +840,11 @@
|
||||
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
/**
|
||||
* Z_MIN_PROBE_ENDSTOP
|
||||
* Z_MIN_PROBE_PIN
|
||||
*
|
||||
* Enable this option for a probe connected to any pin except Z-Min.
|
||||
* (By default Marlin assumes the Z-Max endstop pin.)
|
||||
* To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
|
||||
* Define this pin if the probe is not connected to Z_MIN_PIN.
|
||||
* If not defined the default pin for the selected MOTHERBOARD
|
||||
* will be used. Most of the time the default is what you want.
|
||||
*
|
||||
* - The simplest option is to use a free endstop connector.
|
||||
* - Use 5V for powered (usually inductive) sensors.
|
||||
@ -854,11 +854,8 @@
|
||||
* - normally-closed switches to GND and D32.
|
||||
* - normally-open switches to 5V and D32.
|
||||
*
|
||||
* WARNING: Setting the wrong pin may have unexpected and potentially
|
||||
* disastrous consequences. Use with caution and do your homework.
|
||||
*
|
||||
*/
|
||||
//#define Z_MIN_PROBE_ENDSTOP
|
||||
//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
|
||||
|
||||
/**
|
||||
* Probe Type
|
||||
|
@ -836,11 +836,11 @@
|
||||
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
/**
|
||||
* Z_MIN_PROBE_ENDSTOP
|
||||
* Z_MIN_PROBE_PIN
|
||||
*
|
||||
* Enable this option for a probe connected to any pin except Z-Min.
|
||||
* (By default Marlin assumes the Z-Max endstop pin.)
|
||||
* To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
|
||||
* Define this pin if the probe is not connected to Z_MIN_PIN.
|
||||
* If not defined the default pin for the selected MOTHERBOARD
|
||||
* will be used. Most of the time the default is what you want.
|
||||
*
|
||||
* - The simplest option is to use a free endstop connector.
|
||||
* - Use 5V for powered (usually inductive) sensors.
|
||||
@ -850,11 +850,8 @@
|
||||
* - normally-closed switches to GND and D32.
|
||||
* - normally-open switches to 5V and D32.
|
||||
*
|
||||
* WARNING: Setting the wrong pin may have unexpected and potentially
|
||||
* disastrous consequences. Use with caution and do your homework.
|
||||
*
|
||||
*/
|
||||
//#define Z_MIN_PROBE_ENDSTOP
|
||||
//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
|
||||
|
||||
/**
|
||||
* Probe Type
|
||||
|
@ -836,11 +836,11 @@
|
||||
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
/**
|
||||
* Z_MIN_PROBE_ENDSTOP
|
||||
* Z_MIN_PROBE_PIN
|
||||
*
|
||||
* Enable this option for a probe connected to any pin except Z-Min.
|
||||
* (By default Marlin assumes the Z-Max endstop pin.)
|
||||
* To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
|
||||
* Define this pin if the probe is not connected to Z_MIN_PIN.
|
||||
* If not defined the default pin for the selected MOTHERBOARD
|
||||
* will be used. Most of the time the default is what you want.
|
||||
*
|
||||
* - The simplest option is to use a free endstop connector.
|
||||
* - Use 5V for powered (usually inductive) sensors.
|
||||
@ -850,11 +850,8 @@
|
||||
* - normally-closed switches to GND and D32.
|
||||
* - normally-open switches to 5V and D32.
|
||||
*
|
||||
* WARNING: Setting the wrong pin may have unexpected and potentially
|
||||
* disastrous consequences. Use with caution and do your homework.
|
||||
*
|
||||
*/
|
||||
//#define Z_MIN_PROBE_ENDSTOP
|
||||
//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
|
||||
|
||||
/**
|
||||
* Probe Type
|
||||
|
@ -829,11 +829,11 @@
|
||||
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
/**
|
||||
* Z_MIN_PROBE_ENDSTOP
|
||||
* Z_MIN_PROBE_PIN
|
||||
*
|
||||
* Enable this option for a probe connected to any pin except Z-Min.
|
||||
* (By default Marlin assumes the Z-Max endstop pin.)
|
||||
* To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
|
||||
* Define this pin if the probe is not connected to Z_MIN_PIN.
|
||||
* If not defined the default pin for the selected MOTHERBOARD
|
||||
* will be used. Most of the time the default is what you want.
|
||||
*
|
||||
* - The simplest option is to use a free endstop connector.
|
||||
* - Use 5V for powered (usually inductive) sensors.
|
||||
@ -843,11 +843,8 @@
|
||||
* - normally-closed switches to GND and D32.
|
||||
* - normally-open switches to 5V and D32.
|
||||
*
|
||||
* WARNING: Setting the wrong pin may have unexpected and potentially
|
||||
* disastrous consequences. Use with caution and do your homework.
|
||||
*
|
||||
*/
|
||||
//#define Z_MIN_PROBE_ENDSTOP
|
||||
//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
|
||||
|
||||
/**
|
||||
* Probe Type
|
||||
|
@ -839,11 +839,11 @@
|
||||
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
/**
|
||||
* Z_MIN_PROBE_ENDSTOP
|
||||
* Z_MIN_PROBE_PIN
|
||||
*
|
||||
* Enable this option for a probe connected to any pin except Z-Min.
|
||||
* (By default Marlin assumes the Z-Max endstop pin.)
|
||||
* To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
|
||||
* Define this pin if the probe is not connected to Z_MIN_PIN.
|
||||
* If not defined the default pin for the selected MOTHERBOARD
|
||||
* will be used. Most of the time the default is what you want.
|
||||
*
|
||||
* - The simplest option is to use a free endstop connector.
|
||||
* - Use 5V for powered (usually inductive) sensors.
|
||||
@ -853,11 +853,8 @@
|
||||
* - normally-closed switches to GND and D32.
|
||||
* - normally-open switches to 5V and D32.
|
||||
*
|
||||
* WARNING: Setting the wrong pin may have unexpected and potentially
|
||||
* disastrous consequences. Use with caution and do your homework.
|
||||
*
|
||||
*/
|
||||
//#define Z_MIN_PROBE_ENDSTOP
|
||||
//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
|
||||
|
||||
/**
|
||||
* Probe Type
|
||||
|
@ -777,11 +777,11 @@
|
||||
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
/**
|
||||
* Z_MIN_PROBE_ENDSTOP
|
||||
* Z_MIN_PROBE_PIN
|
||||
*
|
||||
* Enable this option for a probe connected to any pin except Z-Min.
|
||||
* (By default Marlin assumes the Z-Max endstop pin.)
|
||||
* To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
|
||||
* Define this pin if the probe is not connected to Z_MIN_PIN.
|
||||
* If not defined the default pin for the selected MOTHERBOARD
|
||||
* will be used. Most of the time the default is what you want.
|
||||
*
|
||||
* - The simplest option is to use a free endstop connector.
|
||||
* - Use 5V for powered (usually inductive) sensors.
|
||||
@ -791,11 +791,8 @@
|
||||
* - normally-closed switches to GND and D32.
|
||||
* - normally-open switches to 5V and D32.
|
||||
*
|
||||
* WARNING: Setting the wrong pin may have unexpected and potentially
|
||||
* disastrous consequences. Use with caution and do your homework.
|
||||
*
|
||||
*/
|
||||
//#define Z_MIN_PROBE_ENDSTOP
|
||||
//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
|
||||
|
||||
/**
|
||||
* Probe Type
|
||||
|
@ -767,11 +767,11 @@
|
||||
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
/**
|
||||
* Z_MIN_PROBE_ENDSTOP
|
||||
* Z_MIN_PROBE_PIN
|
||||
*
|
||||
* Enable this option for a probe connected to any pin except Z-Min.
|
||||
* (By default Marlin assumes the Z-Max endstop pin.)
|
||||
* To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
|
||||
* Define this pin if the probe is not connected to Z_MIN_PIN.
|
||||
* If not defined the default pin for the selected MOTHERBOARD
|
||||
* will be used. Most of the time the default is what you want.
|
||||
*
|
||||
* - The simplest option is to use a free endstop connector.
|
||||
* - Use 5V for powered (usually inductive) sensors.
|
||||
@ -781,11 +781,8 @@
|
||||
* - normally-closed switches to GND and D32.
|
||||
* - normally-open switches to 5V and D32.
|
||||
*
|
||||
* WARNING: Setting the wrong pin may have unexpected and potentially
|
||||
* disastrous consequences. Use with caution and do your homework.
|
||||
*
|
||||
*/
|
||||
//#define Z_MIN_PROBE_ENDSTOP
|
||||
//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
|
||||
|
||||
/**
|
||||
* Probe Type
|
||||
|
@ -766,11 +766,11 @@
|
||||
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
/**
|
||||
* Z_MIN_PROBE_ENDSTOP
|
||||
* Z_MIN_PROBE_PIN
|
||||
*
|
||||
* Enable this option for a probe connected to any pin except Z-Min.
|
||||
* (By default Marlin assumes the Z-Max endstop pin.)
|
||||
* To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
|
||||
* Define this pin if the probe is not connected to Z_MIN_PIN.
|
||||
* If not defined the default pin for the selected MOTHERBOARD
|
||||
* will be used. Most of the time the default is what you want.
|
||||
*
|
||||
* - The simplest option is to use a free endstop connector.
|
||||
* - Use 5V for powered (usually inductive) sensors.
|
||||
@ -780,11 +780,8 @@
|
||||
* - normally-closed switches to GND and D32.
|
||||
* - normally-open switches to 5V and D32.
|
||||
*
|
||||
* WARNING: Setting the wrong pin may have unexpected and potentially
|
||||
* disastrous consequences. Use with caution and do your homework.
|
||||
*
|
||||
*/
|
||||
//#define Z_MIN_PROBE_ENDSTOP
|
||||
//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
|
||||
|
||||
/**
|
||||
* Probe Type
|
||||
|
@ -759,11 +759,11 @@
|
||||
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
/**
|
||||
* Z_MIN_PROBE_ENDSTOP
|
||||
* Z_MIN_PROBE_PIN
|
||||
*
|
||||
* Enable this option for a probe connected to any pin except Z-Min.
|
||||
* (By default Marlin assumes the Z-Max endstop pin.)
|
||||
* To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
|
||||
* Define this pin if the probe is not connected to Z_MIN_PIN.
|
||||
* If not defined the default pin for the selected MOTHERBOARD
|
||||
* will be used. Most of the time the default is what you want.
|
||||
*
|
||||
* - The simplest option is to use a free endstop connector.
|
||||
* - Use 5V for powered (usually inductive) sensors.
|
||||
@ -773,11 +773,8 @@
|
||||
* - normally-closed switches to GND and D32.
|
||||
* - normally-open switches to 5V and D32.
|
||||
*
|
||||
* WARNING: Setting the wrong pin may have unexpected and potentially
|
||||
* disastrous consequences. Use with caution and do your homework.
|
||||
*
|
||||
*/
|
||||
//#define Z_MIN_PROBE_ENDSTOP
|
||||
//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
|
||||
|
||||
/**
|
||||
* Probe Type
|
||||
|
@ -769,11 +769,11 @@
|
||||
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
/**
|
||||
* Z_MIN_PROBE_ENDSTOP
|
||||
* Z_MIN_PROBE_PIN
|
||||
*
|
||||
* Enable this option for a probe connected to any pin except Z-Min.
|
||||
* (By default Marlin assumes the Z-Max endstop pin.)
|
||||
* To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
|
||||
* Define this pin if the probe is not connected to Z_MIN_PIN.
|
||||
* If not defined the default pin for the selected MOTHERBOARD
|
||||
* will be used. Most of the time the default is what you want.
|
||||
*
|
||||
* - The simplest option is to use a free endstop connector.
|
||||
* - Use 5V for powered (usually inductive) sensors.
|
||||
@ -783,11 +783,8 @@
|
||||
* - normally-closed switches to GND and D32.
|
||||
* - normally-open switches to 5V and D32.
|
||||
*
|
||||
* WARNING: Setting the wrong pin may have unexpected and potentially
|
||||
* disastrous consequences. Use with caution and do your homework.
|
||||
*
|
||||
*/
|
||||
//#define Z_MIN_PROBE_ENDSTOP
|
||||
//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default
|
||||
|
||||
/**
|
||||
* Probe Type
|
||||
|
@ -126,7 +126,7 @@ inline void servo_probe_test() {
|
||||
|
||||
probe_inverting = Z_MIN_ENDSTOP_INVERTING;
|
||||
|
||||
#elif ENABLED(Z_MIN_PROBE_ENDSTOP)
|
||||
#elif USES_Z_MIN_PROBE_ENDSTOP
|
||||
|
||||
#define PROBE_TEST_PIN Z_MIN_PROBE_PIN
|
||||
SERIAL_ECHOLNPAIR(". probe uses Z_MIN_PROBE_PIN: ", PROBE_TEST_PIN);
|
||||
|
@ -505,6 +505,7 @@
|
||||
#define PROBE_SELECTED (HAS_BED_PROBE || ENABLED(PROBE_MANUALLY) || ENABLED(MESH_BED_LEVELING))
|
||||
|
||||
#if HAS_BED_PROBE
|
||||
#define USES_Z_MIN_PROBE_ENDSTOP DISABLED(Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN)
|
||||
#ifndef Z_PROBE_LOW_POINT
|
||||
#define Z_PROBE_LOW_POINT -5
|
||||
#endif
|
||||
@ -514,7 +515,6 @@
|
||||
#else
|
||||
// Clear probe pin settings when no probe is selected
|
||||
#undef Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
#undef Z_MIN_PROBE_ENDSTOP
|
||||
#endif
|
||||
|
||||
#define HOMING_Z_WITH_PROBE (HAS_BED_PROBE && Z_HOME_DIR < 0 && ENABLED(Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN))
|
||||
|
@ -725,12 +725,12 @@
|
||||
// Is an endstop plug used for the Z2 endstop or the bed probe?
|
||||
#define IS_Z2_OR_PROBE(A,M) ( \
|
||||
(Z_MULTI_ENDSTOPS && Z2_USE_ENDSTOP == _##A##M##_) \
|
||||
|| (ENABLED(Z_MIN_PROBE_ENDSTOP) && Z_MIN_PROBE_PIN == A##_##M##_PIN ) )
|
||||
|| (USES_Z_MIN_PROBE_ENDSTOP && Z_MIN_PROBE_PIN == A##_##M##_PIN ) )
|
||||
|
||||
// Is an endstop plug used for the Z3 endstop or the bed probe?
|
||||
#define IS_Z3_OR_PROBE(A,M) ( \
|
||||
(ENABLED(Z_TRIPLE_ENDSTOPS) && Z3_USE_ENDSTOP == _##A##M##_) \
|
||||
|| (ENABLED(Z_MIN_PROBE_ENDSTOP) && Z_MIN_PROBE_PIN == A##_##M##_PIN ) )
|
||||
|| (USES_Z_MIN_PROBE_ENDSTOP && Z_MIN_PROBE_PIN == A##_##M##_PIN ) )
|
||||
|
||||
/**
|
||||
* Set ENDSTOPPULLUPS for active endstop switches
|
||||
@ -894,7 +894,7 @@
|
||||
#define HAS_Z2_MAX (PIN_EXISTS(Z2_MAX))
|
||||
#define HAS_Z3_MIN (PIN_EXISTS(Z3_MIN))
|
||||
#define HAS_Z3_MAX (PIN_EXISTS(Z3_MAX))
|
||||
#define HAS_Z_MIN_PROBE_PIN (PIN_EXISTS(Z_MIN_PROBE))
|
||||
#define HAS_Z_MIN_PROBE_PIN (USES_Z_MIN_PROBE_ENDSTOP && PIN_EXISTS(Z_MIN_PROBE))
|
||||
#define HAS_CALIBRATION_PIN (PIN_EXISTS(CALIBRATION))
|
||||
|
||||
// ADC Temp Sensors (Thermistor or Thermocouple with amplifier ADC interface)
|
||||
|
@ -343,6 +343,8 @@
|
||||
#error "MAX6675_SS2 is now MAX6675_SS2_PIN. Please update your configuration and/or pins."
|
||||
#elif defined(TMC_Z_CALIBRATION)
|
||||
#error "TMC_Z_CALIBRATION has been deprecated in favor of Z_STEPPER_AUTO_ALIGN. Please update your configuration."
|
||||
#elif defined(Z_MIN_PROBE_ENDSTOP)
|
||||
#error "Z_MIN_PROBE_ENDSTOP is no longer required. Please remove it from Configuration.h."
|
||||
#endif
|
||||
|
||||
#define BOARD_MKS_13 -47
|
||||
@ -1018,21 +1020,15 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS
|
||||
#error "SENSORLESS_PROBING requires a TMC2130 driver on Z."
|
||||
#endif
|
||||
#elif ENABLED(Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN)
|
||||
#if ENABLED(Z_MIN_PROBE_ENDSTOP)
|
||||
#error "Enable only one option: Z_MIN_PROBE_ENDSTOP or Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN."
|
||||
#elif DISABLED(USE_ZMIN_PLUG)
|
||||
#if DISABLED(USE_ZMIN_PLUG)
|
||||
#error "Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN requires USE_ZMIN_PLUG to be enabled."
|
||||
#elif !HAS_Z_MIN
|
||||
#error "Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN requires the Z_MIN_PIN to be defined."
|
||||
#elif Z_MIN_PROBE_ENDSTOP_INVERTING != Z_MIN_ENDSTOP_INVERTING
|
||||
#error "Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN requires Z_MIN_ENDSTOP_INVERTING to match Z_MIN_PROBE_ENDSTOP_INVERTING."
|
||||
#endif
|
||||
#elif ENABLED(Z_MIN_PROBE_ENDSTOP)
|
||||
#if !HAS_Z_MIN_PROBE_PIN
|
||||
#error "Z_MIN_PROBE_ENDSTOP requires the Z_MIN_PROBE_PIN to be defined."
|
||||
#endif
|
||||
#else
|
||||
#error "You must enable either Z_MIN_PROBE_ENDSTOP or Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use a probe."
|
||||
#elif !HAS_Z_MIN_PROBE_PIN
|
||||
#error "Z_MIN_PROBE_PIN must be defined if Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN is not enabled."
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
@ -228,7 +228,7 @@ void Endstops::init() {
|
||||
#endif
|
||||
#endif
|
||||
|
||||
#if ENABLED(Z_MIN_PROBE_ENDSTOP)
|
||||
#if USES_Z_MIN_PROBE_ENDSTOP
|
||||
#if ENABLED(ENDSTOPPULLUP_ZMIN_PROBE)
|
||||
SET_INPUT_PULLUP(Z_MIN_PROBE_PIN);
|
||||
#elif ENABLED(ENDSTOPPULLDOWN_ZMIN_PROBE)
|
||||
@ -351,7 +351,7 @@ void Endstops::event_handler() {
|
||||
ENDSTOP_HIT_TEST_Y();
|
||||
ENDSTOP_HIT_TEST_Z();
|
||||
|
||||
#if ENABLED(Z_MIN_PROBE_ENDSTOP)
|
||||
#if USES_Z_MIN_PROBE_ENDSTOP
|
||||
#define P_AXIS Z_AXIS
|
||||
if (TEST(hit_state, Z_MIN_PROBE)) _ENDSTOP_HIT_ECHO(P, 'P');
|
||||
#endif
|
||||
@ -425,7 +425,7 @@ void _O2 Endstops::M119() {
|
||||
#if HAS_Z3_MAX
|
||||
ES_REPORT(Z3_MAX);
|
||||
#endif
|
||||
#if ENABLED(Z_MIN_PROBE_ENDSTOP)
|
||||
#if USES_Z_MIN_PROBE_ENDSTOP
|
||||
print_es_state(READ(Z_MIN_PROBE_PIN) != Z_MIN_PROBE_ENDSTOP_INVERTING, PSTR(MSG_Z_PROBE));
|
||||
#endif
|
||||
#if HAS_FILAMENT_SENSOR
|
||||
@ -586,7 +586,7 @@ void Endstops::update() {
|
||||
#endif
|
||||
|
||||
// When closing the gap check the enabled probe
|
||||
#if ENABLED(Z_MIN_PROBE_ENDSTOP)
|
||||
#if USES_Z_MIN_PROBE_ENDSTOP
|
||||
UPDATE_ENDSTOP_BIT(Z, MIN_PROBE);
|
||||
#endif
|
||||
|
||||
@ -606,7 +606,7 @@ void Endstops::update() {
|
||||
COPY_LIVE_STATE(Z_MAX, Z3_MAX);
|
||||
#endif
|
||||
#endif
|
||||
#elif DISABLED(Z_MIN_PROBE_ENDSTOP) || Z_MAX_PIN != Z_MIN_PROBE_PIN
|
||||
#elif !USES_Z_MIN_PROBE_ENDSTOP || Z_MAX_PIN != Z_MIN_PROBE_PIN
|
||||
// If this pin isn't the bed probe it's the Z endstop
|
||||
UPDATE_ENDSTOP_BIT(Z, MAX);
|
||||
#endif
|
||||
@ -736,7 +736,7 @@ void Endstops::update() {
|
||||
#else
|
||||
#if ENABLED(Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN)
|
||||
if (z_probe_enabled) PROCESS_ENDSTOP(Z, MIN);
|
||||
#elif ENABLED(Z_MIN_PROBE_ENDSTOP)
|
||||
#elif USES_Z_MIN_PROBE_ENDSTOP
|
||||
if (!z_probe_enabled) PROCESS_ENDSTOP(Z, MIN);
|
||||
#else
|
||||
PROCESS_ENDSTOP(Z, MIN);
|
||||
@ -745,7 +745,7 @@ void Endstops::update() {
|
||||
#endif
|
||||
|
||||
// When closing the gap check the enabled probe
|
||||
#if ENABLED(Z_MIN_PROBE_ENDSTOP)
|
||||
#if USES_Z_MIN_PROBE_ENDSTOP
|
||||
if (z_probe_enabled) PROCESS_ENDSTOP(Z, MIN_PROBE);
|
||||
#endif
|
||||
}
|
||||
@ -755,7 +755,7 @@ void Endstops::update() {
|
||||
PROCESS_TRIPLE_ENDSTOP(Z, Z2, Z3, MAX);
|
||||
#elif ENABLED(Z_DUAL_ENDSTOPS)
|
||||
PROCESS_DUAL_ENDSTOP(Z, Z2, MAX);
|
||||
#elif DISABLED(Z_MIN_PROBE_ENDSTOP) || Z_MAX_PIN != Z_MIN_PROBE_PIN
|
||||
#elif !USES_Z_MIN_PROBE_ENDSTOP || Z_MAX_PIN != Z_MIN_PROBE_PIN
|
||||
// If this pin is not hijacked for the bed probe
|
||||
// then it belongs to the Z endstop
|
||||
PROCESS_ENDSTOP(Z, MAX);
|
||||
|
@ -1309,7 +1309,7 @@ void set_axis_is_at_home(const AxisEnum axis) {
|
||||
|
||||
#elif ENABLED(DEBUG_LEVELING_FEATURE)
|
||||
|
||||
if (DEBUGGING(LEVELING)) SERIAL_ECHOLNPGM("*** Z HOMED TO ENDSTOP (Z_MIN_PROBE_ENDSTOP) ***");
|
||||
if (DEBUGGING(LEVELING)) SERIAL_ECHOLNPGM("*** Z HOMED TO ENDSTOP ***");
|
||||
|
||||
#endif
|
||||
}
|
||||
|
@ -450,7 +450,7 @@ bool set_probe_deployed(const bool deploy) {
|
||||
oldYpos = current_position[Y_AXIS];
|
||||
|
||||
#if ENABLED(PROBE_TRIGGERED_WHEN_STOWED_TEST)
|
||||
#if ENABLED(Z_MIN_PROBE_ENDSTOP)
|
||||
#if USES_Z_MIN_PROBE_ENDSTOP
|
||||
#define PROBE_STOWED() (READ(Z_MIN_PROBE_PIN) != Z_MIN_PROBE_ENDSTOP_INVERTING)
|
||||
#else
|
||||
#define PROBE_STOWED() (READ(Z_MIN_PIN) != Z_MIN_ENDSTOP_INVERTING)
|
||||
@ -497,7 +497,7 @@ bool set_probe_deployed(const bool deploy) {
|
||||
#endif
|
||||
|
||||
#if ENABLED(MEASURE_BACKLASH_WHEN_PROBING)
|
||||
#if ENABLED(Z_MIN_PROBE_ENDSTOP)
|
||||
#if USES_Z_MIN_PROBE_ENDSTOP
|
||||
#define TEST_PROBE_PIN (READ(Z_MIN_PROBE_PIN) != Z_MIN_PROBE_ENDSTOP_INVERTING)
|
||||
#else
|
||||
#define TEST_PROBE_PIN (READ(Z_MIN_PIN) != Z_MIN_ENDSTOP_INVERTING)
|
||||
|
Some files were not shown because too many files have changed in this diff Show More
Loading…
Reference in New Issue
Block a user