Merge pull request #3018 from CONSULitAS/RCBugFix_K8200_backinsync

K8200: sample config back in sync

Marlin/example_configurations/K8200/Configuration_adv.h

@@ -1,3 +1,8 @@
+// Sample configuration file for Vellemann K8200
+// tested on K8200 with VM8201 (Display)
+// and Arduino 1.6.8 (Mac) by @CONSULitAS, 2016-02-21
+// https://github.com/CONSULitAS/Marlin-K8200/archive/K8200_stable_2016-02-21.zip
+
 #ifndef CONFIGURATION_ADV_H
 #define CONFIGURATION_ADV_H
 
@@ -18,8 +23,8 @@
  * Thermal Protection parameters
  */
 #if ENABLED(THERMAL_PROTECTION_HOTENDS)
-  #define THERMAL_PROTECTION_PERIOD 40        // Seconds
-  #define THERMAL_PROTECTION_HYSTERESIS 4     // Degrees Celsius
+  #define THERMAL_PROTECTION_PERIOD 60        // Seconds
+  #define THERMAL_PROTECTION_HYSTERESIS 8     // Degrees Celsius
 
   /**
    * Whenever an M104 or M109 increases the target temperature the firmware will wait for the
@@ -27,7 +32,7 @@
    * degrees, the machine is halted, requiring a hard reset. This test restarts with any M104/M109,
    * but only if the current temperature is far enough below the target for a reliable test.
    */
-  #define WATCH_TEMP_PERIOD 16                // Seconds
+  #define WATCH_TEMP_PERIOD 30                // Seconds
   #define WATCH_TEMP_INCREASE 4               // Degrees Celsius
 #endif
 
@@ -93,12 +98,12 @@
 // When first starting the main fan, run it at full speed for the
 // given number of milliseconds.  This gets the fan spinning reliably
 // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
-//#define FAN_KICKSTART_TIME 100
+#define FAN_KICKSTART_TIME 500
 
 // This defines the minimal speed for the main fan, run in PWM mode
 // to enable uncomment and set minimal PWM speed for reliable running (1-255)
 // if fan speed is [1 - (FAN_MIN_PWM-1)] it is set to FAN_MIN_PWM
-#define FAN_MIN_PWM 50 // K8200: fan stops running at about 35 to 40 (of 255)
+#define FAN_MIN_PWM 50
 
 // @section extruder
 
@@ -212,9 +217,9 @@
 //homing hits the endstop, then retracts by this distance, before it tries to slowly bump again:
 #define X_HOME_BUMP_MM 5
 #define Y_HOME_BUMP_MM 5
-#define Z_HOME_BUMP_MM 3
-#define HOMING_BUMP_DIVISOR {2, 2, 4}  // Re-Bump Speed Divisor (Divides the Homing Feedrate)
-//#define QUICK_HOME  //if this is defined, if both x and y are to be homed, a diagonal move will be performed initially.
+#define Z_HOME_BUMP_MM 2
+#define HOMING_BUMP_DIVISOR {4, 4, 8}  // Re-Bump Speed Divisor (Divides the Homing Feedrate)
+#define QUICK_HOME  //if this is defined, if both x and y are to be homed, a diagonal move will be performed initially.
 
 // When G28 is called, this option will make Y home before X
 //#define HOME_Y_BEFORE_X
@@ -303,10 +308,10 @@
   #define SDCARD_RATHERRECENTFIRST  //reverse file order of sd card menu display. Its sorted practically after the file system block order.
   // if a file is deleted, it frees a block. hence, the order is not purely chronological. To still have auto0.g accessible, there is again the option to do that.
   // using:
-  //#define MENU_ADDAUTOSTART
+  #define MENU_ADDAUTOSTART
 
   // Show a progress bar on HD44780 LCDs for SD printing
-  //#define LCD_PROGRESS_BAR
+  #define LCD_PROGRESS_BAR
 
   #if ENABLED(LCD_PROGRESS_BAR)
     // Amount of time (ms) to show the bar
@@ -320,7 +325,7 @@
   #endif
 
   // This allows hosts to request long names for files and folders with M33
-  //#define LONG_FILENAME_HOST_SUPPORT
+  #define LONG_FILENAME_HOST_SUPPORT
 
   // This option allows you to abort SD printing when any endstop is triggered.
   // This feature must be enabled with "M540 S1" or from the LCD menu.
@@ -341,11 +346,10 @@
   //#define USE_SMALL_INFOFONT
 #endif // DOGLCD
 
-
 // @section more
 
 // The hardware watchdog should reset the microcontroller disabling all outputs, in case the firmware gets stuck and doesn't do temperature regulation.
-//#define USE_WATCHDOG
+#define USE_WATCHDOG
 
 #if ENABLED(USE_WATCHDOG)
   // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on.
@@ -359,9 +363,10 @@
 // Babystepping enables the user to control the axis in tiny amounts, independently from the normal printing process
 // it can e.g. be used to change z-positions in the print startup phase in real-time
 // does not respect endstops!
-//#define BABYSTEPPING
+#define BABYSTEPPING
 #if ENABLED(BABYSTEPPING)
   #define BABYSTEP_XY  //not only z, but also XY in the menu. more clutter, more functions
+                       //not implemented for CoreXY and deltabots!
   #define BABYSTEP_INVERT_Z false  //true for inverse movements in Z
   #define BABYSTEP_MULTIPLICATOR 1 //faster movements
 #endif
@@ -388,7 +393,7 @@
 #define MM_PER_ARC_SEGMENT 1
 #define N_ARC_CORRECTION 25
 
-const unsigned int dropsegments = 5; //everything with less than this number of steps will be ignored as move and joined with the next movement
+const unsigned int dropsegments = 2; //everything with less than this number of steps will be ignored as move and joined with the next movement
 
 // @section temperature
 
@@ -406,7 +411,7 @@ const unsigned int dropsegments = 5; //everything with less than this number of
 #if ENABLED(SDSUPPORT)
   #define BLOCK_BUFFER_SIZE 16   // SD,LCD,Buttons take more memory, block buffer needs to be smaller
 #else
-  #define BLOCK_BUFFER_SIZE 16 // maximize block buffer
+  #define BLOCK_BUFFER_SIZE 32 // maximize block buffer
 #endif
 
 // @section more
@@ -453,6 +458,9 @@ const unsigned int dropsegments = 5; //everything with less than this number of
     #define FILAMENTCHANGE_ZADD 10
     #define FILAMENTCHANGE_FIRSTRETRACT -2
     #define FILAMENTCHANGE_FINALRETRACT -100
+    #define AUTO_FILAMENT_CHANGE                //This extrude filament until you press the button on LCD
+    #define AUTO_FILAMENT_CHANGE_LENGTH 0.04    //Extrusion length on automatic extrusion loop
+    #define AUTO_FILAMENT_CHANGE_FEEDRATE 300   //Extrusion feedrate (mm/min) on automatic extrusion loop
   #endif
 #endif