Merge branch '4th-extruders' of https://github.com/MagoKimbra/Marlin into 4th-extruders

Conflicts:
	Marlin/temperature.cpp
This commit is contained in:
MagoKimbra 2015-01-24 13:41:15 +01:00
commit 3d4ee6c868
3 changed files with 39 additions and 20 deletions

View File

@ -44,7 +44,7 @@
// The following define selects which electronics board you have.
// Please choose the name from boards.h that matches your setup
#ifndef MOTHERBOARD
#define MOTHERBOARD BOARD_AZTEEG_X3_PRO
#define MOTHERBOARD BOARD_ULTIMAKER
#endif
// Define this to set a custom name for your generic Mendel,
@ -104,10 +104,9 @@
// 147 is Pt100 with 4k7 pullup
// 110 is Pt100 with 1k pullup (non standard)
#define TEMP_SENSOR_0 1
#define TEMP_SENSOR_1 0
#define TEMP_SENSOR_0 -1
#define TEMP_SENSOR_1 -1
#define TEMP_SENSOR_2 0
#define TEMP_SENSOR_3 0
#define TEMP_SENSOR_BED 0
// This makes temp sensor 1 a redundant sensor for sensor 0. If the temperatures difference between these sensors is to high the print will be aborted.
@ -122,22 +121,20 @@
// The minimal temperature defines the temperature below which the heater will not be enabled It is used
// to check that the wiring to the thermistor is not broken.
// Otherwise this would lead to the heater being powered on all the time.
#define HEATER_0_MINTEMP 5 // degC
#define HEATER_1_MINTEMP 5 // degC
#define HEATER_2_MINTEMP 5 // degC
#define HEATER_3_MINTEMP 5 // degC
#define BED_MINTEMP 5 // degC
#define HEATER_0_MINTEMP 5
#define HEATER_1_MINTEMP 5
#define HEATER_2_MINTEMP 5
#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure!
// You should use MINTEMP for thermistor short/failure protection.
#define HEATER_0_MAXTEMP 275 // degC
#define HEATER_1_MAXTEMP 275 // degC
#define HEATER_2_MAXTEMP 275 // degC
#define HEATER_3_MAXTEMP 275 // degC
#define BED_MAXTEMP 150 // degC
#define HEATER_0_MAXTEMP 275
#define HEATER_1_MAXTEMP 275
#define HEATER_2_MAXTEMP 275
#define BED_MAXTEMP 150
// If your bed has low resistance e.g. 0.6 ohm and throws the fuse you can duty cycle it to reduce the
// If your bed has low resistance e.g. .6 ohm and throws the fuse you can duty cycle it to reduce the
// average current. The value should be an integer and the heat bed will be turned on for 1 interval of
// HEATER_BED_DUTY_CYCLE_DIVIDER intervals.
//#define HEATER_BED_DUTY_CYCLE_DIVIDER 4
@ -224,7 +221,7 @@
//if PREVENT_DANGEROUS_EXTRUDE is on, you can still disable (uncomment) very long bits of extrusion separately.
#define PREVENT_LENGTHY_EXTRUDE
#define EXTRUDE_MINTEMP 170 // degC
#define EXTRUDE_MINTEMP 170
#define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) //prevent extrusion of very large distances.
/*================== Thermal Runaway Protection ==============================
@ -328,7 +325,6 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
#define INVERT_E0_DIR false // for direct drive extruder v9 set to true, for geared extruder set to false
#define INVERT_E1_DIR false // for direct drive extruder v9 set to true, for geared extruder set to false
#define INVERT_E2_DIR false // for direct drive extruder v9 set to true, for geared extruder set to false
#define INVERT_E3_DIR false // for direct drive extruder v9 set to true, for geared extruder set to false
// ENDSTOP SETTINGS:
// Sets direction of endstops when homing; 1=MAX, -1=MIN

View File

@ -1764,6 +1764,7 @@ ISR(TIMER0_COMPB_vect)
raw_temp_2_value += ADC;
#endif
temp_state = 8;
<<<<<<< HEAD
break;
case 8: // Prepare TEMP_3
#if defined(TEMP_3_PIN) && (TEMP_3_PIN > -1)
@ -1784,6 +1785,28 @@ ISR(TIMER0_COMPB_vect)
#endif
temp_state = 10; //change so that Filament Width is also measured
break;
=======
break;
case 8: // Prepare TEMP_3
#if defined(TEMP_3_PIN) && (TEMP_3_PIN > -1)
#if TEMP_3_PIN > 7
ADCSRB = 1<<MUX5;
#else
ADCSRB = 0;
#endif
ADMUX = ((1 << REFS0) | (TEMP_3_PIN & 0x07));
ADCSRA |= 1<<ADSC; // Start conversion
#endif
lcd_buttons_update();
temp_state = 9;
break;
case 9: // Measure TEMP_3
#if defined(TEMP_3_PIN) && (TEMP_3_PIN > -1)
raw_temp_3_value += ADC;
#endif
temp_state = 10; //change so that Filament Width is also measured
break;
>>>>>>> 0ebf896070e8364252df3b3f59111218f1918cc8
case 10: //Prepare FILWIDTH
#if defined(FILWIDTH_PIN) && (FILWIDTH_PIN> -1)
#if FILWIDTH_PIN>7

View File

@ -46,9 +46,9 @@
extern bool cancel_heatup;
#ifdef FILAMENT_LCD_DISPLAY
extern unsigned long message_millis;
#endif
#ifdef FILAMENT_LCD_DISPLAY
extern unsigned long message_millis;
#endif
void lcd_buzz(long duration,uint16_t freq);
bool lcd_clicked();