Provide DOGLCD SPI pins for MKS SBASE + VIKI

This commit is contained in:
Scott Lahteine 2018-11-04 16:20:22 -06:00
parent e0956bb572
commit 3c21483c88

View File

@ -143,31 +143,7 @@
//
// Misc. Functions
//
#define PS_ON_PIN P0_25 //TH3 Connector
/**
* Smart LCD adapter
*
* The Smart LCD adapter can be used for the two 10 pin LCD controllers such as
* REPRAP_DISCOUNT_SMART_CONTROLLER. It can't be used for controllers that use
* DOGLCD_A0, DOGLCD_CS, LCD_PINS_D5, LCD_PINS_D6 or LCD_PINS_D7. A custom cable
* is needed to pick up 5V for the EXP1 connection.
*
* SD card on the LCD uses the same SPI signals as the LCD. This results in garbage/lines
* on the LCD display during accesses of the SD card. The menus/code has been arranged so
* that the garbage/lines are erased immediately after the SD card accesses are completed.
*/
#if ENABLED(ULTRA_LCD)
#define BEEPER_PIN P1_31 // EXP1.1
#define BTN_ENC P1_30 // EXP1.2
#define BTN_EN1 P3_26 // EXP2.5
#define BTN_EN2 P3_25 // EXP2.3
#define LCD_PINS_RS P0_16 // EXP1.4
#define LCD_SDSS P0_28 // EXP2.4
#define LCD_PINS_ENABLE P0_18 // EXP1.3
#define LCD_PINS_D4 P0_15 // EXP1.5
#endif
#define PS_ON_PIN P0_25 // TH3 Connector
//
// Ethernet pins
@ -186,15 +162,14 @@
#define ENET_TXD0 P1_00 // J12-11
#define ENET_TXD1 P1_01 // J12-12
/*
/**
* The SBase can share the on-board SD card with a PC via USB the following
* definitions control this feature:
*/
//#define USB_SD_DISABLED
#define USB_SD_ONBOARD // Provide the onboard SD card to the host as a USB mass storage device
/*
/**
* There are a number of configurations available for the SBase SD card reader.
* - A custom cable can be used to allow access to the LCD based SD card.
* - A standard cable can be used for access to the LCD SD card (but no SD detect).
@ -256,6 +231,34 @@
#endif
/**
* Smart LCD adapter
*
* The Smart LCD adapter can be used for the two 10 pin LCD controllers such as
* REPRAP_DISCOUNT_SMART_CONTROLLER. It can't be used for controllers that use
* DOGLCD_A0, DOGLCD_CS, LCD_PINS_D5, LCD_PINS_D6 or LCD_PINS_D7. A custom cable
* is needed to pick up 5V for the EXP1 connection.
*
* SD card on the LCD uses the same SPI signals as the LCD. This results in garbage/lines
* on the LCD display during accesses of the SD card. The menus/code has been arranged so
* that the garbage/lines are erased immediately after the SD card accesses are completed.
*/
#if ENABLED(ULTRA_LCD)
#define BEEPER_PIN P1_31 // EXP1.1
#define BTN_ENC P1_30 // EXP1.2
#define BTN_EN1 P3_26 // EXP2.5
#define BTN_EN2 P3_25 // EXP2.3
#define LCD_PINS_RS P0_16 // EXP1.4
#define LCD_SDSS P0_28 // EXP2.4
#define LCD_PINS_ENABLE P0_18 // EXP1.3
#define LCD_PINS_D4 P0_15 // EXP1.5
#if ENABLED(VIKI2) || ENABLED(miniVIKI)
#define DOGLCD_SCK SCK_PIN
#define DOGLCD_MOSI MOSI_PIN
#endif
#endif
/**
* Example for trinamic drivers using the J8 connector on MKs Sbase.
* 2130s need 1 pin for each driver. 2208s need 2 pins for serial control.