BigTreeTech GTR V1.0 / Support 8 extruders, heaters, temp sensors, fans (#16595)

This commit is contained in:
yangwenxiong 2020-01-25 16:13:39 +08:00 committed by Scott Lahteine
parent 0d166f9c7d
commit 248b7dfa59
66 changed files with 2086 additions and 217 deletions

View File

@ -279,14 +279,25 @@ enum ClockSource2 : char {
*/ */
// Determine which harware PWMs are already in use // Determine which harware PWMs are already in use
#define _PWM_CHK_FAN_B(P) (P == E0_AUTO_FAN_PIN || P == E1_AUTO_FAN_PIN || P == E2_AUTO_FAN_PIN || P == E3_AUTO_FAN_PIN || P == E4_AUTO_FAN_PIN || P == E5_AUTO_FAN_PIN || P == E6_AUTO_FAN_PIN || P == E7_AUTO_FAN_PIN || P == CHAMBER_AUTO_FAN_PIN)
#if PIN_EXISTS(CONTROLLER_FAN) #if PIN_EXISTS(CONTROLLER_FAN)
#define PWM_CHK_FAN_B(P) (P == CONTROLLER_FAN_PIN || P == E0_AUTO_FAN_PIN || P == E1_AUTO_FAN_PIN || P == E2_AUTO_FAN_PIN || P == E3_AUTO_FAN_PIN || P == E4_AUTO_FAN_PIN || P == E5_AUTO_FAN_PIN || P == CHAMBER_AUTO_FAN_PIN) #define PWM_CHK_FAN_B(P) (_PWM_CHK_FAN_B(P) || P == CONTROLLER_FAN_PIN)
#else #else
#define PWM_CHK_FAN_B(P) (P == E0_AUTO_FAN_PIN || P == E1_AUTO_FAN_PIN || P == E2_AUTO_FAN_PIN || P == E3_AUTO_FAN_PIN || P == E4_AUTO_FAN_PIN || P == E5_AUTO_FAN_PIN || P == CHAMBER_AUTO_FAN_PIN) #define PWM_CHK_FAN_B(P) _PWM_CHK_FAN_B(P)
#endif #endif
#if ANY_PIN(FAN, FAN1, FAN2) #if ANY_PIN(FAN, FAN1, FAN2, FAN3, FAN4, FAN5, FAN6, FAN7)
#if PIN_EXISTS(FAN2) #if PIN_EXISTS(FAN7)
#define PWM_CHK_FAN_A(P) (P == FAN0_PIN || P == FAN1_PIN || P == FAN2_PIN || P == FAN3_PIN || P == FAN4_PIN || P == FAN5_PIN || P == FAN6_PIN || P == FAN7_PIN)
#elif PIN_EXISTS(FAN6)
#define PWM_CHK_FAN_A(P) (P == FAN0_PIN || P == FAN1_PIN || P == FAN2_PIN || P == FAN3_PIN || P == FAN4_PIN || P == FAN5_PIN || P == FAN6_PIN)
#elif PIN_EXISTS(FAN5)
#define PWM_CHK_FAN_A(P) (P == FAN0_PIN || P == FAN1_PIN || P == FAN2_PIN || P == FAN3_PIN || P == FAN4_PIN || P == FAN5_PIN)
#elif PIN_EXISTS(FAN4)
#define PWM_CHK_FAN_A(P) (P == FAN0_PIN || P == FAN1_PIN || P == FAN2_PIN || P == FAN3_PIN || P == FAN4_PIN)
#elif PIN_EXISTS(FAN3)
#define PWM_CHK_FAN_A(P) (P == FAN0_PIN || P == FAN1_PIN || P == FAN2_PIN || P == FAN3_PIN)
#elif PIN_EXISTS(FAN2)
#define PWM_CHK_FAN_A(P) (P == FAN0_PIN || P == FAN1_PIN || P == FAN2_PIN) #define PWM_CHK_FAN_A(P) (P == FAN0_PIN || P == FAN1_PIN || P == FAN2_PIN)
#elif PIN_EXISTS(FAN1) #elif PIN_EXISTS(FAN1)
#define PWM_CHK_FAN_A(P) (P == FAN0_PIN || P == FAN1_PIN) #define PWM_CHK_FAN_A(P) (P == FAN0_PIN || P == FAN1_PIN)

View File

@ -46,6 +46,10 @@
#error "TEMP_4_PIN must be defined using the Pn_nn or Pn_nn_An format. (See the included pins files)." #error "TEMP_4_PIN must be defined using the Pn_nn or Pn_nn_An format. (See the included pins files)."
#elif _OLD_TEMP_PIN(TEMP_5) #elif _OLD_TEMP_PIN(TEMP_5)
#error "TEMP_5_PIN must be defined using the Pn_nn or Pn_nn_An format. (See the included pins files)." #error "TEMP_5_PIN must be defined using the Pn_nn or Pn_nn_An format. (See the included pins files)."
#elif _OLD_TEMP_PIN(TEMP_6)
#error "TEMP_6_PIN must be defined using the Pn_nn or Pn_nn_An format. (See the included pins files)."
#elif _OLD_TEMP_PIN(TEMP_7)
#error "TEMP_7_PIN must be defined using the Pn_nn or Pn_nn_An format. (See the included pins files)."
#endif #endif
#undef _OLD_TEMP_PIN #undef _OLD_TEMP_PIN

View File

@ -59,6 +59,16 @@
#else #else
#define GET_TEMP_5_ADC() -1 #define GET_TEMP_5_ADC() -1
#endif #endif
#if HAS_TEMP_ADC_6
#define GET_TEMP_6_ADC() PIN_TO_ADC(TEMP_6_PIN)
#else
#define GET_TEMP_6_ADC() -1
#endif
#if HAS_TEMP_ADC_7
#define GET_TEMP_7_ADC() PIN_TO_ADC(TEMP_7_PIN)
#else
#define GET_TEMP_7_ADC() -1
#endif
#if HAS_TEMP_PROBE #if HAS_TEMP_PROBE
#define GET_PROBE_ADC() PIN_TO_ADC(TEMP_PROBE_PIN) #define GET_PROBE_ADC() PIN_TO_ADC(TEMP_PROBE_PIN)
#else #else
@ -85,13 +95,15 @@
#define GET_BUTTONS_ADC() -1 #define GET_BUTTONS_ADC() -1
#endif #endif
#define IS_ADC_REQUIRED(n) (GET_TEMP_0_ADC() == n || GET_TEMP_1_ADC() == n || GET_TEMP_2_ADC() == n \ #define IS_ADC_REQUIRED(n) ( \
|| GET_TEMP_3_ADC() == n || GET_TEMP_4_ADC() == n || GET_TEMP_5_ADC() == n \ GET_TEMP_0_ADC() == n || GET_TEMP_1_ADC() == n || GET_TEMP_2_ADC() == n || GET_TEMP_3_ADC() == n \
|| GET_TEMP_4_ADC() == n || GET_TEMP_5_ADC() == n || GET_TEMP_6_ADC() == n || GET_TEMP_7_ADC() == n \
|| GET_PROBE_ADC() == n \ || GET_PROBE_ADC() == n \
|| GET_BED_ADC() == n \ || GET_BED_ADC() == n \
|| GET_CHAMBER_ADC() == n \ || GET_CHAMBER_ADC() == n \
|| GET_FILAMENT_WIDTH_ADC() == n \ || GET_FILAMENT_WIDTH_ADC() == n \
|| GET_BUTTONS_ADC() == n) || GET_BUTTONS_ADC() == n \
)
#define ADC0_IS_REQUIRED IS_ADC_REQUIRED(0) #define ADC0_IS_REQUIRED IS_ADC_REQUIRED(0)
#define ADC1_IS_REQUIRED IS_ADC_REQUIRED(1) #define ADC1_IS_REQUIRED IS_ADC_REQUIRED(1)
@ -151,6 +163,12 @@ uint16_t HAL_adc_result;
#if GET_TEMP_5_ADC() == 0 #if GET_TEMP_5_ADC() == 0
TEMP_5_PIN, TEMP_5_PIN,
#endif #endif
#if GET_TEMP_6_ADC() == 0
TEMP_6_PIN,
#endif
#if GET_TEMP_7_ADC() == 0
TEMP_7_PIN,
#endif
#if GET_PROBE_ADC() == 0 #if GET_PROBE_ADC() == 0
TEMP_PROBE_PIN, TEMP_PROBE_PIN,
#endif #endif
@ -185,6 +203,12 @@ uint16_t HAL_adc_result;
#if GET_TEMP_5_ADC() == 1 #if GET_TEMP_5_ADC() == 1
TEMP_5_PIN, TEMP_5_PIN,
#endif #endif
#if GET_TEMP_6_ADC() == 1
TEMP_6_PIN,
#endif
#if GET_TEMP_7_ADC() == 1
TEMP_7_PIN,
#endif
#if GET_PROBE_ADC() == 1 #if GET_PROBE_ADC() == 1
TEMP_PROBE_PIN, TEMP_PROBE_PIN,
#endif #endif
@ -227,6 +251,12 @@ uint16_t HAL_adc_result;
#if GET_TEMP_5_ADC() == 0 #if GET_TEMP_5_ADC() == 0
{ PIN_TO_INPUTCTRL(TEMP_5_PIN) }, { PIN_TO_INPUTCTRL(TEMP_5_PIN) },
#endif #endif
#if GET_TEMP_6_ADC() == 0
{ PIN_TO_INPUTCTRL(TEMP_6_PIN) },
#endif
#if GET_TEMP_7_ADC() == 0
{ PIN_TO_INPUTCTRL(TEMP_7_PIN) },
#endif
#if GET_PROBE_ADC() == 0 #if GET_PROBE_ADC() == 0
{ PIN_TO_INPUTCTRL(TEMP_PROBE_PIN) }, { PIN_TO_INPUTCTRL(TEMP_PROBE_PIN) },
#endif #endif
@ -270,6 +300,12 @@ uint16_t HAL_adc_result;
#if GET_TEMP_5_ADC() == 1 #if GET_TEMP_5_ADC() == 1
{ PIN_TO_INPUTCTRL(TEMP_5_PIN) }, { PIN_TO_INPUTCTRL(TEMP_5_PIN) },
#endif #endif
#if GET_TEMP_6_ADC() == 1
{ PIN_TO_INPUTCTRL(TEMP_6_PIN) },
#endif
#if GET_TEMP_7_ADC() == 1
{ PIN_TO_INPUTCTRL(TEMP_7_PIN) },
#endif
#if GET_PROBE_ADC() == 1 #if GET_PROBE_ADC() == 1
{ PIN_TO_INPUTCTRL(TEMP_PROBE_PIN) }, { PIN_TO_INPUTCTRL(TEMP_PROBE_PIN) },
#endif #endif

View File

@ -118,6 +118,12 @@ const uint8_t adc_pins[] = {
#if HAS_TEMP_ADC_5 #if HAS_TEMP_ADC_5
TEMP_5_PIN, TEMP_5_PIN,
#endif #endif
#if HAS_TEMP_ADC_6
TEMP_6_PIN,
#endif
#if HAS_TEMP_ADC_7
TEMP_7_PIN,
#endif
#if ENABLED(FILAMENT_WIDTH_SENSOR) #if ENABLED(FILAMENT_WIDTH_SENSOR)
FILWIDTH_PIN, FILWIDTH_PIN,
#endif #endif
@ -160,6 +166,12 @@ enum TEMP_PINS : char {
#if HAS_TEMP_ADC_5 #if HAS_TEMP_ADC_5
TEMP_5, TEMP_5,
#endif #endif
#if HAS_TEMP_ADC_6
TEMP_6,
#endif
#if HAS_TEMP_ADC_7
TEMP_7,
#endif
#if ENABLED(FILAMENT_WIDTH_SENSOR) #if ENABLED(FILAMENT_WIDTH_SENSOR)
FILWIDTH, FILWIDTH,
#endif #endif
@ -346,6 +358,12 @@ void HAL_adc_start_conversion(const uint8_t adc_pin) {
#if HAS_TEMP_ADC_5 #if HAS_TEMP_ADC_5
case TEMP_5_PIN: pin_index = TEMP_5; break; case TEMP_5_PIN: pin_index = TEMP_5; break;
#endif #endif
#if HAS_TEMP_ADC_6
case TEMP_6_PIN: pin_index = TEMP_6; break;
#endif
#if HAS_TEMP_ADC_7
case TEMP_7_PIN: pin_index = TEMP_7; break;
#endif
#if HAS_JOY_ADC_X #if HAS_JOY_ADC_X
case JOY_X_PIN: pin_index = JOY_X; break; case JOY_X_PIN: pin_index = JOY_X; break;
#endif #endif

View File

@ -79,7 +79,8 @@
#define HAS_E_DRIVER(T) ( AXIS_DRIVER_TYPE_E0(T) || AXIS_DRIVER_TYPE_E1(T) \ #define HAS_E_DRIVER(T) ( AXIS_DRIVER_TYPE_E0(T) || AXIS_DRIVER_TYPE_E1(T) \
|| AXIS_DRIVER_TYPE_E2(T) || AXIS_DRIVER_TYPE_E3(T) \ || AXIS_DRIVER_TYPE_E2(T) || AXIS_DRIVER_TYPE_E3(T) \
|| AXIS_DRIVER_TYPE_E4(T) || AXIS_DRIVER_TYPE_E5(T) ) || AXIS_DRIVER_TYPE_E4(T) || AXIS_DRIVER_TYPE_E5(T) \
|| AXIS_DRIVER_TYPE_E6(T) || AXIS_DRIVER_TYPE_E7(T) )
#define HAS_DRIVER(T) ( AXIS_DRIVER_TYPE_X(T) || AXIS_DRIVER_TYPE_X2(T) \ #define HAS_DRIVER(T) ( AXIS_DRIVER_TYPE_X(T) || AXIS_DRIVER_TYPE_X2(T) \
|| AXIS_DRIVER_TYPE_Y(T) || AXIS_DRIVER_TYPE_Y2(T) \ || AXIS_DRIVER_TYPE_Y(T) || AXIS_DRIVER_TYPE_Y2(T) \
@ -152,7 +153,8 @@
|| AXIS_HAS_##T(Z3) \ || AXIS_HAS_##T(Z3) \
|| AXIS_HAS_##T(E0) || AXIS_HAS_##T(E1) \ || AXIS_HAS_##T(E0) || AXIS_HAS_##T(E1) \
|| AXIS_HAS_##T(E2) || AXIS_HAS_##T(E3) \ || AXIS_HAS_##T(E2) || AXIS_HAS_##T(E3) \
|| AXIS_HAS_##T(E4) || AXIS_HAS_##T(E5) ) || AXIS_HAS_##T(E4) || AXIS_HAS_##T(E5) \
|| AXIS_HAS_##T(E6) || AXIS_HAS_##T(E7) )
#define HAS_STEALTHCHOP ANY_AXIS_HAS(STEALTHCHOP) #define HAS_STEALTHCHOP ANY_AXIS_HAS(STEALTHCHOP)
#define HAS_STALLGUARD ANY_AXIS_HAS(STALLGUARD) #define HAS_STALLGUARD ANY_AXIS_HAS(STALLGUARD)

View File

@ -359,6 +359,8 @@
#define LCD_STR_N3 "3" #define LCD_STR_N3 "3"
#define LCD_STR_N4 "4" #define LCD_STR_N4 "4"
#define LCD_STR_N5 "5" #define LCD_STR_N5 "5"
#define LCD_STR_N6 "6"
#define LCD_STR_N7 "7"
#else #else
#define LCD_FIRST_TOOL '1' #define LCD_FIRST_TOOL '1'
#define LCD_STR_N0 "1" #define LCD_STR_N0 "1"
@ -367,6 +369,8 @@
#define LCD_STR_N3 "4" #define LCD_STR_N3 "4"
#define LCD_STR_N4 "5" #define LCD_STR_N4 "5"
#define LCD_STR_N5 "6" #define LCD_STR_N5 "6"
#define LCD_STR_N6 "7"
#define LCD_STR_N7 "8"
#endif #endif
#define LCD_STR_E0 "E" LCD_STR_N0 #define LCD_STR_E0 "E" LCD_STR_N0
@ -375,6 +379,8 @@
#define LCD_STR_E3 "E" LCD_STR_N3 #define LCD_STR_E3 "E" LCD_STR_N3
#define LCD_STR_E4 "E" LCD_STR_N4 #define LCD_STR_E4 "E" LCD_STR_N4
#define LCD_STR_E5 "E" LCD_STR_N5 #define LCD_STR_E5 "E" LCD_STR_N5
#define LCD_STR_E6 "E" LCD_STR_N6
#define LCD_STR_E7 "E" LCD_STR_N7
#include "multi_language.h" // Allow multiple languages #include "multi_language.h" // Allow multiple languages

View File

@ -43,11 +43,7 @@ enum AxisEnum : uint8_t {
E_AXIS = 3, E_AXIS = 3,
X_HEAD = 4, Y_HEAD = 5, Z_HEAD = 6, X_HEAD = 4, Y_HEAD = 5, Z_HEAD = 6,
E0_AXIS = 3, E0_AXIS = 3,
E1_AXIS = 4, E1_AXIS, E2_AXIS, E3_AXIS, E4_AXIS, E5_AXIS, E6_AXIS, E7_AXIS,
E2_AXIS = 5,
E3_AXIS = 6,
E4_AXIS = 7,
E5_AXIS = 8,
ALL_AXES = 0xFE, NO_AXIS = 0xFF ALL_AXES = 0xFE, NO_AXIS = 0xFF
}; };

View File

@ -47,23 +47,38 @@ void GcodeSuite::M42() {
const pin_t pin = GET_PIN_MAP_PIN(pin_index); const pin_t pin = GET_PIN_MAP_PIN(pin_index);
#if FAN_COUNT > 0
switch (pin) {
#if HAS_FAN0
case FAN0_PIN: thermalManager.fan_speed[0] = pin_status; return;
#endif
#if HAS_FAN1
case FAN1_PIN: thermalManager.fan_speed[1] = pin_status; return;
#endif
#if HAS_FAN2
case FAN2_PIN: thermalManager.fan_speed[2] = pin_status; return;
#endif
#if HAS_FAN3
case FAN3_PIN: thermalManager.fan_speed[3] = pin_status; return;
#endif
#if HAS_FAN4
case FAN4_PIN: thermalManager.fan_speed[4] = pin_status; return;
#endif
#if HAS_FAN5
case FAN5_PIN: thermalManager.fan_speed[5] = pin_status; return;
#endif
#if HAS_FAN6
case FAN6_PIN: thermalManager.fan_speed[6] = pin_status; return;
#endif
#if HAS_FAN7
case FAN7_PIN: thermalManager.fan_speed[7] = pin_status; return;
#endif
}
#endif
if (!parser.boolval('I') && pin_is_protected(pin)) return protected_pin_err(); if (!parser.boolval('I') && pin_is_protected(pin)) return protected_pin_err();
pinMode(pin, OUTPUT); pinMode(pin, OUTPUT);
extDigitalWrite(pin, pin_status); extDigitalWrite(pin, pin_status);
analogWrite(pin, pin_status); analogWrite(pin, pin_status);
#if FAN_COUNT > 0
switch (pin) {
#if HAS_FAN0
case FAN0_PIN: thermalManager.fan_speed[0] = pin_status; break;
#endif
#if HAS_FAN1
case FAN1_PIN: thermalManager.fan_speed[1] = pin_status; break;
#endif
#if HAS_FAN2
case FAN2_PIN: thermalManager.fan_speed[2] = pin_status; break;
#endif
}
#endif
} }

View File

@ -38,7 +38,7 @@
#define M91x_SOME_X (M91x_USE(X) || M91x_USE(X2)) #define M91x_SOME_X (M91x_USE(X) || M91x_USE(X2))
#define M91x_SOME_Y (M91x_USE(Y) || M91x_USE(Y2)) #define M91x_SOME_Y (M91x_USE(Y) || M91x_USE(Y2))
#define M91x_SOME_Z (M91x_USE(Z) || M91x_USE(Z2) || M91x_USE(Z3) || M91x_USE(Z4)) #define M91x_SOME_Z (M91x_USE(Z) || M91x_USE(Z2) || M91x_USE(Z3) || M91x_USE(Z4))
#define M91x_SOME_E (M91x_USE_E(0) || M91x_USE_E(1) || M91x_USE_E(2) || M91x_USE_E(3) || M91x_USE_E(4) || M91x_USE_E(5)) #define M91x_SOME_E (M91x_USE_E(0) || M91x_USE_E(1) || M91x_USE_E(2) || M91x_USE_E(3) || M91x_USE_E(4) || M91x_USE_E(5) || M91x_USE_E(6) || M91x_USE_E(7))
#if !M91x_SOME_X && !M91x_SOME_Y && !M91x_SOME_Z && !M91x_SOME_E #if !M91x_SOME_X && !M91x_SOME_Y && !M91x_SOME_Z && !M91x_SOME_E
#error "MONITOR_DRIVER_STATUS requires at least one TMC2130, 2160, 2208, 2209, 2660, 5130, or 5160." #error "MONITOR_DRIVER_STATUS requires at least one TMC2130, 2160, 2208, 2209, 2660, 5130, or 5160."
@ -91,6 +91,12 @@
#if M91x_USE_E(5) #if M91x_USE_E(5)
tmc_report_otpw(stepperE5); tmc_report_otpw(stepperE5);
#endif #endif
#if M91x_USE_E(6)
tmc_report_otpw(stepperE6);
#endif
#if M91x_USE_E(7)
tmc_report_otpw(stepperE7);
#endif
} }
/** /**
@ -188,6 +194,12 @@
#if M91x_USE_E(5) #if M91x_USE_E(5)
if (hasNone || eval == 5 || (hasE && eval < 0)) tmc_clear_otpw(stepperE5); if (hasNone || eval == 5 || (hasE && eval < 0)) tmc_clear_otpw(stepperE5);
#endif #endif
#if M91x_USE_E(6)
if (hasNone || eval == 6 || (hasE && eval < 0)) tmc_clear_otpw(stepperE6);
#endif
#if M91x_USE_E(7)
if (hasNone || eval == 7 || (hasE && eval < 0)) tmc_clear_otpw(stepperE7);
#endif
#endif #endif
} }
@ -263,6 +275,12 @@
#if E_STEPPERS > 5 && AXIS_HAS_STEALTHCHOP(E5) #if E_STEPPERS > 5 && AXIS_HAS_STEALTHCHOP(E5)
case 5: TMC_SET_PWMTHRS_E(5); break; case 5: TMC_SET_PWMTHRS_E(5); break;
#endif #endif
#if E_STEPPERS > 6 && AXIS_HAS_STEALTHCHOP(E6)
case 6: TMC_SET_PWMTHRS_E(6); break;
#endif
#if E_STEPPERS > 7 && AXIS_HAS_STEALTHCHOP(E7)
case 7: TMC_SET_PWMTHRS_E(7); break;
#endif
} }
#endif // E_STEPPERS #endif // E_STEPPERS
} break; } break;
@ -312,6 +330,12 @@
#if E_STEPPERS > 5 && AXIS_HAS_STEALTHCHOP(E5) #if E_STEPPERS > 5 && AXIS_HAS_STEALTHCHOP(E5)
TMC_SAY_PWMTHRS_E(5); TMC_SAY_PWMTHRS_E(5);
#endif #endif
#if E_STEPPERS > 6 && AXIS_HAS_STEALTHCHOP(E6)
TMC_SAY_PWMTHRS_E(6);
#endif
#if E_STEPPERS > 7 && AXIS_HAS_STEALTHCHOP(E7)
TMC_SAY_PWMTHRS_E(7);
#endif
} }
} }
#endif // HYBRID_THRESHOLD #endif // HYBRID_THRESHOLD

View File

@ -34,6 +34,8 @@
#undef TEMP_SENSOR_3 #undef TEMP_SENSOR_3
#undef TEMP_SENSOR_4 #undef TEMP_SENSOR_4
#undef TEMP_SENSOR_5 #undef TEMP_SENSOR_5
#undef TEMP_SENSOR_6
#undef TEMP_SENSOR_7
#undef FWRETRACT #undef FWRETRACT
#undef PIDTEMP #undef PIDTEMP
#undef AUTOTEMP #undef AUTOTEMP

View File

@ -341,7 +341,7 @@
* Temp Sensor defines * Temp Sensor defines
*/ */
#define ANY_TEMP_SENSOR_IS(n) (TEMP_SENSOR_0 == (n) || TEMP_SENSOR_1 == (n) || TEMP_SENSOR_2 == (n) || TEMP_SENSOR_3 == (n) || TEMP_SENSOR_4 == (n) || TEMP_SENSOR_5 == (n) || TEMP_SENSOR_BED == (n) || TEMP_SENSOR_PROBE == (n) || TEMP_SENSOR_CHAMBER == (n)) #define ANY_TEMP_SENSOR_IS(n) (TEMP_SENSOR_0 == (n) || TEMP_SENSOR_1 == (n) || TEMP_SENSOR_2 == (n) || TEMP_SENSOR_3 == (n) || TEMP_SENSOR_4 == (n) || TEMP_SENSOR_5 == (n) || TEMP_SENSOR_6 == (n) || TEMP_SENSOR_7 == (n) || TEMP_SENSOR_BED == (n) || TEMP_SENSOR_PROBE == (n) || TEMP_SENSOR_CHAMBER == (n))
#define HAS_USER_THERMISTORS ANY_TEMP_SENSOR_IS(1000) #define HAS_USER_THERMISTORS ANY_TEMP_SENSOR_IS(1000)
@ -483,6 +483,44 @@
#undef HEATER_5_MAXTEMP #undef HEATER_5_MAXTEMP
#endif #endif
#if TEMP_SENSOR_6 == -4
#define HEATER_6_USES_AD8495
#elif TEMP_SENSOR_6 == -3
#error "MAX31855 Thermocouples (-3) not supported for TEMP_SENSOR_6."
#elif TEMP_SENSOR_6 == -2
#error "MAX6675 Thermocouples (-2) not supported for TEMP_SENSOR_6."
#elif TEMP_SENSOR_6 == -1
#define HEATER_6_USES_AD595
#elif TEMP_SENSOR_6 > 0
#define THERMISTOR_HEATER_6 TEMP_SENSOR_6
#define HEATER_6_USES_THERMISTOR
#if TEMP_SENSOR_6 == 1000
#define HEATER_6_USER_THERMISTOR
#endif
#else
#undef HEATER_6_MINTEMP
#undef HEATER_6_MAXTEMP
#endif
#if TEMP_SENSOR_7 == -4
#define HEATER_7_USES_AD8495
#elif TEMP_SENSOR_7 == -3
#error "MAX31855 Thermocouples (-3) not supported for TEMP_SENSOR_7."
#elif TEMP_SENSOR_7 == -2
#error "MAX7775 Thermocouples (-2) not supported for TEMP_SENSOR_7."
#elif TEMP_SENSOR_7 == -1
#define HEATER_7_USES_AD595
#elif TEMP_SENSOR_7 > 0
#define THERMISTOR_HEATER_7 TEMP_SENSOR_7
#define HEATER_7_USES_THERMISTOR
#if TEMP_SENSOR_7 == 1000
#define HEATER_7_USER_THERMISTOR
#endif
#else
#undef HEATER_7_MINTEMP
#undef HEATER_7_MAXTEMP
#endif
#if TEMP_SENSOR_BED == -4 #if TEMP_SENSOR_BED == -4
#define HEATER_BED_USES_AD8495 #define HEATER_BED_USES_AD8495
#elif TEMP_SENSOR_BED == -3 #elif TEMP_SENSOR_BED == -3
@ -538,8 +576,8 @@
#endif #endif
#define HOTEND_USES_THERMISTOR ANY( \ #define HOTEND_USES_THERMISTOR ANY( \
HEATER_0_USES_THERMISTOR, HEATER_1_USES_THERMISTOR, HEATER_2_USES_THERMISTOR, \ HEATER_0_USES_THERMISTOR, HEATER_1_USES_THERMISTOR, HEATER_2_USES_THERMISTOR, HEATER_3_USES_THERMISTOR, \
HEATER_3_USES_THERMISTOR, HEATER_4_USES_THERMISTOR, HEATER_5_USES_THERMISTOR) HEATER_4_USES_THERMISTOR, HEATER_5_USES_THERMISTOR, HEATER_6_USES_THERMISTOR, HEATER_7_USES_THERMISTOR )
/** /**
* Default hotend offsets, if not defined * Default hotend offsets, if not defined
@ -1025,6 +1063,18 @@
#define HAS_E5_MICROSTEPS (PIN_EXISTS(E5_MS1)) #define HAS_E5_MICROSTEPS (PIN_EXISTS(E5_MS1))
#define HAS_SOLENOID_5 (PIN_EXISTS(SOL5)) #define HAS_SOLENOID_5 (PIN_EXISTS(SOL5))
#define HAS_E6_ENABLE (PIN_EXISTS(E6_ENABLE) || (ENABLED(SOFTWARE_DRIVER_ENABLE) && AXIS_IS_TMC(E6)))
#define HAS_E6_DIR (PIN_EXISTS(E6_DIR))
#define HAS_E6_STEP (PIN_EXISTS(E6_STEP))
#define HAS_E6_MICROSTEPS (PIN_EXISTS(E6_MS1))
#define HAS_SOLENOID_6 (PIN_EXISTS(SOL6))
#define HAS_E7_ENABLE (PIN_EXISTS(E7_ENABLE) || (ENABLED(SOFTWARE_DRIVER_ENABLE) && AXIS_IS_TMC(E7)))
#define HAS_E7_DIR (PIN_EXISTS(E7_DIR))
#define HAS_E7_STEP (PIN_EXISTS(E7_STEP))
#define HAS_E7_MICROSTEPS (PIN_EXISTS(E7_MS1))
#define HAS_SOLENOID_7 (PIN_EXISTS(SOL7))
// Trinamic Stepper Drivers // Trinamic Stepper Drivers
#if HAS_TRINAMIC #if HAS_TRINAMIC
#define STEALTHCHOP_ENABLED ANY(STEALTHCHOP_XY, STEALTHCHOP_Z, STEALTHCHOP_E) #define STEALTHCHOP_ENABLED ANY(STEALTHCHOP_XY, STEALTHCHOP_Z, STEALTHCHOP_E)
@ -1095,6 +1145,8 @@
#define HAS_TEMP_ADC_3 HAS_ADC_TEST(3) #define HAS_TEMP_ADC_3 HAS_ADC_TEST(3)
#define HAS_TEMP_ADC_4 HAS_ADC_TEST(4) #define HAS_TEMP_ADC_4 HAS_ADC_TEST(4)
#define HAS_TEMP_ADC_5 HAS_ADC_TEST(5) #define HAS_TEMP_ADC_5 HAS_ADC_TEST(5)
#define HAS_TEMP_ADC_6 HAS_ADC_TEST(6)
#define HAS_TEMP_ADC_7 HAS_ADC_TEST(7)
#define HAS_TEMP_ADC_BED HAS_ADC_TEST(BED) #define HAS_TEMP_ADC_BED HAS_ADC_TEST(BED)
#define HAS_TEMP_ADC_PROBE HAS_ADC_TEST(PROBE) #define HAS_TEMP_ADC_PROBE HAS_ADC_TEST(PROBE)
#define HAS_TEMP_ADC_CHAMBER HAS_ADC_TEST(CHAMBER) #define HAS_TEMP_ADC_CHAMBER HAS_ADC_TEST(CHAMBER)
@ -1118,6 +1170,8 @@
#define HAS_HEATER_3 (PIN_EXISTS(HEATER_3)) #define HAS_HEATER_3 (PIN_EXISTS(HEATER_3))
#define HAS_HEATER_4 (PIN_EXISTS(HEATER_4)) #define HAS_HEATER_4 (PIN_EXISTS(HEATER_4))
#define HAS_HEATER_5 (PIN_EXISTS(HEATER_5)) #define HAS_HEATER_5 (PIN_EXISTS(HEATER_5))
#define HAS_HEATER_6 (PIN_EXISTS(HEATER_6))
#define HAS_HEATER_7 (PIN_EXISTS(HEATER_7))
#define HAS_HEATER_BED (PIN_EXISTS(HEATER_BED)) #define HAS_HEATER_BED (PIN_EXISTS(HEATER_BED))
// Shorthand for common combinations // Shorthand for common combinations
@ -1146,12 +1200,14 @@
#define HAS_AUTO_FAN_3 (HOTENDS > 3 && PIN_EXISTS(E3_AUTO_FAN)) #define HAS_AUTO_FAN_3 (HOTENDS > 3 && PIN_EXISTS(E3_AUTO_FAN))
#define HAS_AUTO_FAN_4 (HOTENDS > 4 && PIN_EXISTS(E4_AUTO_FAN)) #define HAS_AUTO_FAN_4 (HOTENDS > 4 && PIN_EXISTS(E4_AUTO_FAN))
#define HAS_AUTO_FAN_5 (HOTENDS > 5 && PIN_EXISTS(E5_AUTO_FAN)) #define HAS_AUTO_FAN_5 (HOTENDS > 5 && PIN_EXISTS(E5_AUTO_FAN))
#define HAS_AUTO_FAN_6 (HOTENDS > 6 && PIN_EXISTS(E6_AUTO_FAN))
#define HAS_AUTO_FAN_7 (HOTENDS > 7 && PIN_EXISTS(E7_AUTO_FAN))
#define HAS_AUTO_CHAMBER_FAN (HAS_TEMP_CHAMBER && PIN_EXISTS(CHAMBER_AUTO_FAN)) #define HAS_AUTO_CHAMBER_FAN (HAS_TEMP_CHAMBER && PIN_EXISTS(CHAMBER_AUTO_FAN))
#define HAS_AUTO_FAN (HAS_AUTO_FAN_0 || HAS_AUTO_FAN_1 || HAS_AUTO_FAN_2 || HAS_AUTO_FAN_3 || HAS_AUTO_FAN_4 || HAS_AUTO_FAN_5 || HAS_AUTO_CHAMBER_FAN) #define HAS_AUTO_FAN (HAS_AUTO_FAN_0 || HAS_AUTO_FAN_1 || HAS_AUTO_FAN_2 || HAS_AUTO_FAN_3 || HAS_AUTO_FAN_4 || HAS_AUTO_FAN_5 || HAS_AUTO_FAN_6 || HAS_AUTO_FAN_7 || HAS_AUTO_CHAMBER_FAN)
#define _FANOVERLAP(A,B) (A##_AUTO_FAN_PIN == E##B##_AUTO_FAN_PIN) #define _FANOVERLAP(A,B) (A##_AUTO_FAN_PIN == E##B##_AUTO_FAN_PIN)
#if HAS_AUTO_FAN #if HAS_AUTO_FAN
#define AUTO_CHAMBER_IS_E (_FANOVERLAP(CHAMBER,0) || _FANOVERLAP(CHAMBER,1) || _FANOVERLAP(CHAMBER,2) || _FANOVERLAP(CHAMBER,3) || _FANOVERLAP(CHAMBER,4) || _FANOVERLAP(CHAMBER,5)) #define AUTO_CHAMBER_IS_E (_FANOVERLAP(CHAMBER,0) || _FANOVERLAP(CHAMBER,1) || _FANOVERLAP(CHAMBER,2) || _FANOVERLAP(CHAMBER,3) || _FANOVERLAP(CHAMBER,4) || _FANOVERLAP(CHAMBER,5) || _FANOVERLAP(CHAMBER,6) || _FANOVERLAP(CHAMBER,7))
#endif #endif
#if !HAS_TEMP_SENSOR #if !HAS_TEMP_SENSOR
@ -1164,8 +1220,14 @@
// Other fans // Other fans
#define HAS_FAN0 (PIN_EXISTS(FAN)) #define HAS_FAN0 (PIN_EXISTS(FAN))
#define HAS_FAN1 (PIN_EXISTS(FAN1) && CONTROLLER_FAN_PIN != FAN1_PIN && E0_AUTO_FAN_PIN != FAN1_PIN && E1_AUTO_FAN_PIN != FAN1_PIN && E2_AUTO_FAN_PIN != FAN1_PIN && E3_AUTO_FAN_PIN != FAN1_PIN && E4_AUTO_FAN_PIN != FAN1_PIN && E5_AUTO_FAN_PIN != FAN1_PIN) #define _HAS_FAN(P) (PIN_EXISTS(FAN_##P) && CONTROLLER_FAN_PIN != FAN_##P##_PIN && E0_AUTO_FAN_PIN != FAN_##P##_PIN && E1_AUTO_FAN_PIN != FAN_##P##_PIN && E2_AUTO_FAN_PIN != FAN_##P##_PIN && E3_AUTO_FAN_PIN != FAN_##P##_PIN && E4_AUTO_FAN_PIN != FAN_##P##_PIN && E5_AUTO_FAN_PIN != FAN_##P##_PIN && E6_AUTO_FAN_PIN != FAN_##P##_PIN && E7_AUTO_FAN_PIN != FAN_##P##_PIN)
#define HAS_FAN2 (PIN_EXISTS(FAN2) && CONTROLLER_FAN_PIN != FAN2_PIN && E0_AUTO_FAN_PIN != FAN2_PIN && E1_AUTO_FAN_PIN != FAN2_PIN && E2_AUTO_FAN_PIN != FAN2_PIN && E3_AUTO_FAN_PIN != FAN2_PIN && E4_AUTO_FAN_PIN != FAN2_PIN && E5_AUTO_FAN_PIN != FAN2_PIN) #define HAS_FAN1 _HAS_FAN(1)
#define HAS_FAN2 _HAS_FAN(2)
#define HAS_FAN3 _HAS_FAN(3)
#define HAS_FAN4 _HAS_FAN(4)
#define HAS_FAN5 _HAS_FAN(5)
#define HAS_FAN6 _HAS_FAN(6)
#define HAS_FAN7 _HAS_FAN(7)
#define HAS_CONTROLLER_FAN (PIN_EXISTS(CONTROLLER_FAN)) #define HAS_CONTROLLER_FAN (PIN_EXISTS(CONTROLLER_FAN))
// Servos // Servos
@ -1203,7 +1265,7 @@
#define HAS_MOTOR_CURRENT_PWM ANY_PIN(MOTOR_CURRENT_PWM_X, MOTOR_CURRENT_PWM_Y, MOTOR_CURRENT_PWM_XY, MOTOR_CURRENT_PWM_Z, MOTOR_CURRENT_PWM_E) #define HAS_MOTOR_CURRENT_PWM ANY_PIN(MOTOR_CURRENT_PWM_X, MOTOR_CURRENT_PWM_Y, MOTOR_CURRENT_PWM_XY, MOTOR_CURRENT_PWM_Z, MOTOR_CURRENT_PWM_E)
#define HAS_SOME_Z_MICROSTEPS (HAS_Z_MICROSTEPS || HAS_Z2_MICROSTEPS || HAS_Z3_MICROSTEPS || HAS_Z4_MICROSTEPS) #define HAS_SOME_Z_MICROSTEPS (HAS_Z_MICROSTEPS || HAS_Z2_MICROSTEPS || HAS_Z3_MICROSTEPS || HAS_Z4_MICROSTEPS)
#define HAS_SOME_E_MICROSTEPS (HAS_E0_MICROSTEPS || HAS_E1_MICROSTEPS || HAS_E2_MICROSTEPS || HAS_E3_MICROSTEPS || HAS_E4_MICROSTEPS || HAS_E5_MICROSTEPS) #define HAS_SOME_E_MICROSTEPS (HAS_E0_MICROSTEPS || HAS_E1_MICROSTEPS || HAS_E2_MICROSTEPS || HAS_E3_MICROSTEPS || HAS_E4_MICROSTEPS || HAS_E5_MICROSTEPS || HAS_E6_MICROSTEPS || HAS_E7_MICROSTEPS)
#define HAS_MICROSTEPS (HAS_X_MICROSTEPS || HAS_X2_MICROSTEPS || HAS_Y_MICROSTEPS || HAS_Y2_MICROSTEPS || HAS_SOME_Z_MICROSTEPS || HAS_SOME_E_MICROSTEPS) #define HAS_MICROSTEPS (HAS_X_MICROSTEPS || HAS_X2_MICROSTEPS || HAS_Y_MICROSTEPS || HAS_Y2_MICROSTEPS || HAS_SOME_Z_MICROSTEPS || HAS_SOME_E_MICROSTEPS)
#if HAS_MICROSTEPS #if HAS_MICROSTEPS
@ -1278,26 +1340,27 @@
#if HAS_HEATER_0 && !defined(HEATER_0_INVERTING) #if HAS_HEATER_0 && !defined(HEATER_0_INVERTING)
#define HEATER_0_INVERTING false #define HEATER_0_INVERTING false
#endif #endif
#if HAS_HEATER_1 && !defined(HEATER_1_INVERTING) #if HAS_HEATER_1 && !defined(HEATER_1_INVERTING)
#define HEATER_1_INVERTING false #define HEATER_1_INVERTING false
#endif #endif
#if HAS_HEATER_2 && !defined(HEATER_2_INVERTING) #if HAS_HEATER_2 && !defined(HEATER_2_INVERTING)
#define HEATER_2_INVERTING false #define HEATER_2_INVERTING false
#endif #endif
#if HAS_HEATER_3 && !defined(HEATER_3_INVERTING) #if HAS_HEATER_3 && !defined(HEATER_3_INVERTING)
#define HEATER_3_INVERTING false #define HEATER_3_INVERTING false
#endif #endif
#if HAS_HEATER_4 && !defined(HEATER_4_INVERTING) #if HAS_HEATER_4 && !defined(HEATER_4_INVERTING)
#define HEATER_4_INVERTING false #define HEATER_4_INVERTING false
#endif #endif
#if HAS_HEATER_5 && !defined(HEATER_5_INVERTING) #if HAS_HEATER_5 && !defined(HEATER_5_INVERTING)
#define HEATER_5_INVERTING false #define HEATER_5_INVERTING false
#endif #endif
#if HAS_HEATER_6 && !defined(HEATER_6_INVERTING)
#define HEATER_6_INVERTING false
#endif
#if HAS_HEATER_7 && !defined(HEATER_7_INVERTING)
#define HEATER_7_INVERTING false
#endif
/** /**
* Helper Macros for heaters and extruder fan * Helper Macros for heaters and extruder fan
@ -1314,6 +1377,12 @@
#define WRITE_HEATER_4(v) WRITE(HEATER_4_PIN, (v) ^ HEATER_4_INVERTING) #define WRITE_HEATER_4(v) WRITE(HEATER_4_PIN, (v) ^ HEATER_4_INVERTING)
#if HOTENDS > 5 #if HOTENDS > 5
#define WRITE_HEATER_5(v) WRITE(HEATER_5_PIN, (v) ^ HEATER_5_INVERTING) #define WRITE_HEATER_5(v) WRITE(HEATER_5_PIN, (v) ^ HEATER_5_INVERTING)
#if HOTENDS > 6
#define WRITE_HEATER_6(v) WRITE(HEATER_6_PIN, (v) ^ HEATER_6_INVERTING)
#if HOTENDS > 7
#define WRITE_HEATER_7(v) WRITE(HEATER_7_PIN, (v) ^ HEATER_7_INVERTING)
#endif // HOTENDS > 7
#endif // HOTENDS > 6
#endif // HOTENDS > 5 #endif // HOTENDS > 5
#endif // HOTENDS > 4 #endif // HOTENDS > 4
#endif // HOTENDS > 3 #endif // HOTENDS > 3
@ -1365,7 +1434,17 @@
#define FAN_INVERTING false #define FAN_INVERTING false
#endif #endif
#if HAS_FAN2 #if HAS_FAN7
#define FAN_COUNT 8
#elif HAS_FAN6
#define FAN_COUNT 7
#elif HAS_FAN5
#define FAN_COUNT 6
#elif HAS_FAN4
#define FAN_COUNT 5
#elif HAS_FAN3
#define FAN_COUNT 4
#elif HAS_FAN2
#define FAN_COUNT 3 #define FAN_COUNT 3
#elif HAS_FAN1 #elif HAS_FAN1
#define FAN_COUNT 2 #define FAN_COUNT 2
@ -1640,7 +1719,6 @@
#define HAS_FIXED_3POINT #define HAS_FIXED_3POINT
#endif #endif
/** /**
* Buzzer/Speaker * Buzzer/Speaker
*/ */

View File

@ -294,19 +294,19 @@
#elif defined(HAVE_L6470DRIVER) #elif defined(HAVE_L6470DRIVER)
#error "HAVE_L6470DRIVER is now [AXIS]_DRIVER_TYPE L6470. Please update your Configuration.h." #error "HAVE_L6470DRIVER is now [AXIS]_DRIVER_TYPE L6470. Please update your Configuration.h."
#elif defined(X_IS_TMC) || defined(X2_IS_TMC) || defined(Y_IS_TMC) || defined(Y2_IS_TMC) || defined(Z_IS_TMC) || defined(Z2_IS_TMC) || defined(Z3_IS_TMC) \ #elif defined(X_IS_TMC) || defined(X2_IS_TMC) || defined(Y_IS_TMC) || defined(Y2_IS_TMC) || defined(Z_IS_TMC) || defined(Z2_IS_TMC) || defined(Z3_IS_TMC) \
|| defined(E0_IS_TMC) || defined(E1_IS_TMC) || defined(E2_IS_TMC) || defined(E3_IS_TMC) || defined(E4_IS_TMC) || defined(E5_IS_TMC) || defined(E0_IS_TMC) || defined(E1_IS_TMC) || defined(E2_IS_TMC) || defined(E3_IS_TMC) || defined(E4_IS_TMC) || defined(E5_IS_TMC) || defined(E6_IS_TMC) || defined(E7_IS_TMC)
#error "[AXIS]_IS_TMC is now [AXIS]_DRIVER_TYPE TMC26X. Please update your Configuration.h." #error "[AXIS]_IS_TMC is now [AXIS]_DRIVER_TYPE TMC26X. Please update your Configuration.h."
#elif defined(X_IS_TMC26X) || defined(X2_IS_TMC26X) || defined(Y_IS_TMC26X) || defined(Y2_IS_TMC26X) || defined(Z_IS_TMC26X) || defined(Z2_IS_TMC26X) || defined(Z3_IS_TMC26X) \ #elif defined(X_IS_TMC26X) || defined(X2_IS_TMC26X) || defined(Y_IS_TMC26X) || defined(Y2_IS_TMC26X) || defined(Z_IS_TMC26X) || defined(Z2_IS_TMC26X) || defined(Z3_IS_TMC26X) \
|| defined(E0_IS_TMC26X) || defined(E1_IS_TMC26X) || defined(E2_IS_TMC26X) || defined(E3_IS_TMC26X) || defined(E4_IS_TMC26X) || defined(E5_IS_TMC26X) || defined(E0_IS_TMC26X) || defined(E1_IS_TMC26X) || defined(E2_IS_TMC26X) || defined(E3_IS_TMC26X) || defined(E4_IS_TMC26X) || defined(E5_IS_TMC26X) || defined(E6_IS_TMC26X) || defined(E7_IS_TMC26X)
#error "[AXIS]_IS_TMC26X is now [AXIS]_DRIVER_TYPE TMC26X. Please update your Configuration.h." #error "[AXIS]_IS_TMC26X is now [AXIS]_DRIVER_TYPE TMC26X. Please update your Configuration.h."
#elif defined(X_IS_TMC2130) || defined(X2_IS_TMC2130) || defined(Y_IS_TMC2130) || defined(Y2_IS_TMC2130) || defined(Z_IS_TMC2130) || defined(Z2_IS_TMC2130) || defined(Z3_IS_TMC2130) \ #elif defined(X_IS_TMC2130) || defined(X2_IS_TMC2130) || defined(Y_IS_TMC2130) || defined(Y2_IS_TMC2130) || defined(Z_IS_TMC2130) || defined(Z2_IS_TMC2130) || defined(Z3_IS_TMC2130) \
|| defined(E0_IS_TMC2130) || defined(E1_IS_TMC2130) || defined(E2_IS_TMC2130) || defined(E3_IS_TMC2130) || defined(E4_IS_TMC2130) || defined(E5_IS_TMC2130) || defined(E0_IS_TMC2130) || defined(E1_IS_TMC2130) || defined(E2_IS_TMC2130) || defined(E3_IS_TMC2130) || defined(E4_IS_TMC2130) || defined(E5_IS_TMC2130) || defined(E6_IS_TMC2130) || defined(E7_IS_TMC2130)
#error "[AXIS]_IS_TMC2130 is now [AXIS]_DRIVER_TYPE TMC2130. Please update your Configuration.h." #error "[AXIS]_IS_TMC2130 is now [AXIS]_DRIVER_TYPE TMC2130. Please update your Configuration.h."
#elif defined(X_IS_TMC2208) || defined(X2_IS_TMC2208) || defined(Y_IS_TMC2208) || defined(Y2_IS_TMC2208) || defined(Z_IS_TMC2208) || defined(Z2_IS_TMC2208) || defined(Z3_IS_TMC2208) \ #elif defined(X_IS_TMC2208) || defined(X2_IS_TMC2208) || defined(Y_IS_TMC2208) || defined(Y2_IS_TMC2208) || defined(Z_IS_TMC2208) || defined(Z2_IS_TMC2208) || defined(Z3_IS_TMC2208) \
|| defined(E0_IS_TMC2208) || defined(E1_IS_TMC2208) || defined(E2_IS_TMC2208) || defined(E3_IS_TMC2208) || defined(E4_IS_TMC2208) || defined(E5_IS_TMC2208) || defined(E0_IS_TMC2208) || defined(E1_IS_TMC2208) || defined(E2_IS_TMC2208) || defined(E3_IS_TMC2208) || defined(E4_IS_TMC2208) || defined(E5_IS_TMC2208) || defined(E6_IS_TMC2208) || defined(E7_IS_TMC2208)
#error "[AXIS]_IS_TMC2208 is now [AXIS]_DRIVER_TYPE TMC2208. Please update your Configuration.h." #error "[AXIS]_IS_TMC2208 is now [AXIS]_DRIVER_TYPE TMC2208. Please update your Configuration.h."
#elif defined(X_IS_L6470) || defined(X2_IS_L6470) || defined(Y_IS_L6470) || defined(Y2_IS_L6470) || defined(Z_IS_L6470) || defined(Z2_IS_L6470) || defined(Z3_IS_L6470) \ #elif defined(X_IS_L6470) || defined(X2_IS_L6470) || defined(Y_IS_L6470) || defined(Y2_IS_L6470) || defined(Z_IS_L6470) || defined(Z2_IS_L6470) || defined(Z3_IS_L6470) \
|| defined(E0_IS_L6470) || defined(E1_IS_L6470) || defined(E2_IS_L6470) || defined(E3_IS_L6470) || defined(E4_IS_L6470) || defined(E5_IS_L6470) || defined(E0_IS_L6470) || defined(E1_IS_L6470) || defined(E2_IS_L6470) || defined(E3_IS_L6470) || defined(E4_IS_L6470) || defined(E5_IS_L6470) || defined(E6_IS_L6470) || defined(E7_IS_L6470)
#error "[AXIS]_IS_L6470 is now [AXIS]_DRIVER_TYPE L6470. Please update your Configuration.h." #error "[AXIS]_IS_L6470 is now [AXIS]_DRIVER_TYPE L6470. Please update your Configuration.h."
#elif defined(AUTOMATIC_CURRENT_CONTROL) #elif defined(AUTOMATIC_CURRENT_CONTROL)
#error "AUTOMATIC_CURRENT_CONTROL is now MONITOR_DRIVER_STATUS. Please update your configuration." #error "AUTOMATIC_CURRENT_CONTROL is now MONITOR_DRIVER_STATUS. Please update your configuration."
@ -752,8 +752,8 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS
*/ */
#if EXTRUDERS > 1 #if EXTRUDERS > 1
#if EXTRUDERS > 6 #if EXTRUDERS > 8
#error "Marlin supports a maximum of 6 EXTRUDERS." #error "Marlin supports a maximum of 8 EXTRUDERS."
#endif #endif
#if ENABLED(HEATERS_PARALLEL) #if ENABLED(HEATERS_PARALLEL)
@ -1494,6 +1494,10 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS
#error "TEMP_SENSOR_4 1000 requires HOTEND4_PULLUP_RESISTOR_OHMS, HOTEND4_RESISTANCE_25C_OHMS and HOTEND4_BETA in Configuration_adv.h." #error "TEMP_SENSOR_4 1000 requires HOTEND4_PULLUP_RESISTOR_OHMS, HOTEND4_RESISTANCE_25C_OHMS and HOTEND4_BETA in Configuration_adv.h."
#elif ENABLED(HEATER_5_USER_THERMISTOR) && !(defined(HOTEND5_PULLUP_RESISTOR_OHMS) && defined(HOTEND5_RESISTANCE_25C_OHMS) && defined(HOTEND5_BETA)) #elif ENABLED(HEATER_5_USER_THERMISTOR) && !(defined(HOTEND5_PULLUP_RESISTOR_OHMS) && defined(HOTEND5_RESISTANCE_25C_OHMS) && defined(HOTEND5_BETA))
#error "TEMP_SENSOR_5 1000 requires HOTEND5_PULLUP_RESISTOR_OHMS, HOTEND5_RESISTANCE_25C_OHMS and HOTEND5_BETA in Configuration_adv.h." #error "TEMP_SENSOR_5 1000 requires HOTEND5_PULLUP_RESISTOR_OHMS, HOTEND5_RESISTANCE_25C_OHMS and HOTEND5_BETA in Configuration_adv.h."
#elif ENABLED(HEATER_6_USER_THERMISTOR) && !(defined(HOTEND6_PULLUP_RESISTOR_OHMS) && defined(HOTEND6_RESISTANCE_25C_OHMS) && defined(HOTEND6_BETA))
#error "TEMP_SENSOR_6 1000 requires HOTEND6_PULLUP_RESISTOR_OHMS, HOTEND6_RESISTANCE_25C_OHMS and HOTEND6_BETA in Configuration_adv.h."
#elif ENABLED(HEATER_7_USER_THERMISTOR) && !(defined(HOTEND7_PULLUP_RESISTOR_OHMS) && defined(HOTEND7_RESISTANCE_25C_OHMS) && defined(HOTEND7_BETA))
#error "TEMP_SENSOR_7 1000 requires HOTEND7_PULLUP_RESISTOR_OHMS, HOTEND7_RESISTANCE_25C_OHMS and HOTEND7_BETA in Configuration_adv.h."
#elif ENABLED(HEATER_BED_USER_THERMISTOR) && !(defined(BED_PULLUP_RESISTOR_OHMS) && defined(BED_RESISTANCE_25C_OHMS) && defined(BED_BETA)) #elif ENABLED(HEATER_BED_USER_THERMISTOR) && !(defined(BED_PULLUP_RESISTOR_OHMS) && defined(BED_RESISTANCE_25C_OHMS) && defined(BED_BETA))
#error "TEMP_SENSOR_BED 1000 requires BED_PULLUP_RESISTOR_OHMS, BED_RESISTANCE_25C_OHMS and BED_BETA in Configuration_adv.h." #error "TEMP_SENSOR_BED 1000 requires BED_PULLUP_RESISTOR_OHMS, BED_RESISTANCE_25C_OHMS and BED_BETA in Configuration_adv.h."
#elif ENABLED(HEATER_CHAMBER_USER_THERMISTOR) && !(defined(CHAMBER_PULLUP_RESISTOR_OHMS) && defined(CHAMBER_RESISTANCE_25C_OHMS) && defined(CHAMBER_BETA)) #elif ENABLED(HEATER_CHAMBER_USER_THERMISTOR) && !(defined(CHAMBER_PULLUP_RESISTOR_OHMS) && defined(CHAMBER_RESISTANCE_25C_OHMS) && defined(CHAMBER_BETA))
@ -1564,13 +1568,45 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS
#elif !PIN_EXISTS(TEMP_5) #elif !PIN_EXISTS(TEMP_5)
#error "TEMP_5_PIN not defined for this board." #error "TEMP_5_PIN not defined for this board."
#endif #endif
#if HOTENDS > 6
#if TEMP_SENSOR_6 == 0
#error "TEMP_SENSOR_6 is required with 6 HOTENDS."
#elif !HAS_HEATER_6
#error "HEATER_6_PIN not defined for this board."
#elif !PIN_EXISTS(TEMP_6)
#error "TEMP_6_PIN not defined for this board."
#endif
#if HOTENDS > 7
#if TEMP_SENSOR_7 == 0
#error "TEMP_SENSOR_7 is required with 7 HOTENDS."
#elif !HAS_HEATER_7
#error "HEATER_7_PIN not defined for this board."
#elif !PIN_EXISTS(TEMP_7)
#error "TEMP_7_PIN not defined for this board."
#endif
#elif TEMP_SENSOR_7 != 0
#error "TEMP_SENSOR_7 shouldn't be set with only 7 HOTENDS."
#endif
#elif TEMP_SENSOR_6 != 0
#error "TEMP_SENSOR_6 shouldn't be set with only 6 HOTENDS."
#elif TEMP_SENSOR_7 != 0
#error "TEMP_SENSOR_7 shouldn't be set with only 6 HOTENDS."
#endif
#elif TEMP_SENSOR_5 != 0 #elif TEMP_SENSOR_5 != 0
#error "TEMP_SENSOR_5 shouldn't be set with only 5 HOTENDS." #error "TEMP_SENSOR_5 shouldn't be set with only 5 HOTENDS."
#elif TEMP_SENSOR_6 != 0
#error "TEMP_SENSOR_6 shouldn't be set with only 5 HOTENDS."
#elif TEMP_SENSOR_7 != 0
#error "TEMP_SENSOR_7 shouldn't be set with only 5 HOTENDS."
#endif #endif
#elif TEMP_SENSOR_4 != 0 #elif TEMP_SENSOR_4 != 0
#error "TEMP_SENSOR_4 shouldn't be set with only 4 HOTENDS." #error "TEMP_SENSOR_4 shouldn't be set with only 4 HOTENDS."
#elif TEMP_SENSOR_5 != 0 #elif TEMP_SENSOR_5 != 0
#error "TEMP_SENSOR_5 shouldn't be set with only 4 HOTENDS." #error "TEMP_SENSOR_5 shouldn't be set with only 4 HOTENDS."
#elif TEMP_SENSOR_6 != 0
#error "TEMP_SENSOR_6 shouldn't be set with only 4 HOTENDS."
#elif TEMP_SENSOR_7 != 0
#error "TEMP_SENSOR_7 shouldn't be set with only 4 HOTENDS."
#endif #endif
#elif TEMP_SENSOR_3 != 0 #elif TEMP_SENSOR_3 != 0
#error "TEMP_SENSOR_3 shouldn't be set with only 3 HOTENDS." #error "TEMP_SENSOR_3 shouldn't be set with only 3 HOTENDS."
@ -1578,6 +1614,10 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS
#error "TEMP_SENSOR_4 shouldn't be set with only 3 HOTENDS." #error "TEMP_SENSOR_4 shouldn't be set with only 3 HOTENDS."
#elif TEMP_SENSOR_5 != 0 #elif TEMP_SENSOR_5 != 0
#error "TEMP_SENSOR_5 shouldn't be set with only 3 HOTENDS." #error "TEMP_SENSOR_5 shouldn't be set with only 3 HOTENDS."
#elif TEMP_SENSOR_6 != 0
#error "TEMP_SENSOR_6 shouldn't be set with only 3 HOTENDS."
#elif TEMP_SENSOR_7 != 0
#error "TEMP_SENSOR_7 shouldn't be set with only 3 HOTENDS."
#endif #endif
#elif TEMP_SENSOR_2 != 0 #elif TEMP_SENSOR_2 != 0
#error "TEMP_SENSOR_2 shouldn't be set with only 2 HOTENDS." #error "TEMP_SENSOR_2 shouldn't be set with only 2 HOTENDS."
@ -1587,6 +1627,10 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS
#error "TEMP_SENSOR_4 shouldn't be set with only 2 HOTENDS." #error "TEMP_SENSOR_4 shouldn't be set with only 2 HOTENDS."
#elif TEMP_SENSOR_5 != 0 #elif TEMP_SENSOR_5 != 0
#error "TEMP_SENSOR_5 shouldn't be set with only 2 HOTENDS." #error "TEMP_SENSOR_5 shouldn't be set with only 2 HOTENDS."
#elif TEMP_SENSOR_6 != 0
#error "TEMP_SENSOR_6 shouldn't be set with only 2 HOTENDS."
#elif TEMP_SENSOR_7 != 0
#error "TEMP_SENSOR_7 shouldn't be set with only 2 HOTENDS."
#endif #endif
#elif TEMP_SENSOR_1 != 0 && DISABLED(TEMP_SENSOR_1_AS_REDUNDANT) #elif TEMP_SENSOR_1 != 0 && DISABLED(TEMP_SENSOR_1_AS_REDUNDANT)
#error "TEMP_SENSOR_1 shouldn't be set with only 1 HOTEND." #error "TEMP_SENSOR_1 shouldn't be set with only 1 HOTEND."
@ -1598,6 +1642,10 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS
#error "TEMP_SENSOR_4 shouldn't be set with only 1 HOTEND." #error "TEMP_SENSOR_4 shouldn't be set with only 1 HOTEND."
#elif TEMP_SENSOR_5 != 0 #elif TEMP_SENSOR_5 != 0
#error "TEMP_SENSOR_5 shouldn't be set with only 1 HOTEND." #error "TEMP_SENSOR_5 shouldn't be set with only 1 HOTEND."
#elif TEMP_SENSOR_6 != 0
#error "TEMP_SENSOR_6 shouldn't be set with only 1 HOTEND."
#elif TEMP_SENSOR_7 != 0
#error "TEMP_SENSOR_7 shouldn't be set with only 1 HOTEND."
#endif #endif
#if TEMP_SENSOR_PROBE #if TEMP_SENSOR_PROBE
@ -1680,6 +1728,16 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS
#if !(PIN_EXISTS(E5_STEP, E5_DIR) && HAS_E5_ENABLE) #if !(PIN_EXISTS(E5_STEP, E5_DIR) && HAS_E5_ENABLE)
#error "E5_STEP_PIN, E5_DIR_PIN, or E5_ENABLE_PIN not defined for this board." #error "E5_STEP_PIN, E5_DIR_PIN, or E5_ENABLE_PIN not defined for this board."
#endif #endif
#if E_STEPPERS > 6
#if !(PIN_EXISTS(E6_STEP, E6_DIR) && HAS_E6_ENABLE)
#error "E6_STEP_PIN, E6_DIR_PIN, or E6_ENABLE_PIN not defined for this board."
#endif
#if E_STEPPERS > 7
#if !(PIN_EXISTS(E7_STEP, E7_DIR) && HAS_E7_ENABLE)
#error "E7_STEP_PIN, E7_DIR_PIN, or E7_ENABLE_PIN not defined for this board."
#endif
#endif // E_STEPPERS > 7
#endif // E_STEPPERS > 6
#endif // E_STEPPERS > 5 #endif // E_STEPPERS > 5
#endif // E_STEPPERS > 4 #endif // E_STEPPERS > 4
#endif // E_STEPPERS > 3 #endif // E_STEPPERS > 3
@ -2008,6 +2066,10 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS
#error "An SPI driven TMC driver on E4 requires E4_CS_PIN." #error "An SPI driven TMC driver on E4 requires E4_CS_PIN."
#elif INVALID_TMC_SPI(E5) #elif INVALID_TMC_SPI(E5)
#error "An SPI driven TMC driver on E5 requires E5_CS_PIN." #error "An SPI driven TMC driver on E5 requires E5_CS_PIN."
#elif INVALID_TMC_SPI(E6)
#error "An SPI driven TMC driver on E6 requires E6_CS_PIN."
#elif INVALID_TMC_SPI(E7)
#error "An SPI driven TMC driver on E7 requires E7_CS_PIN."
#endif #endif
#undef INVALID_TMC_SPI #undef INVALID_TMC_SPI
@ -2041,6 +2103,10 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS
#error "TMC2208 or TMC2209 on E4 requires E4_HARDWARE_SERIAL or E4_SERIAL_(RX|TX)_PIN." #error "TMC2208 or TMC2209 on E4 requires E4_HARDWARE_SERIAL or E4_SERIAL_(RX|TX)_PIN."
#elif INVALID_TMC_UART(E5) #elif INVALID_TMC_UART(E5)
#error "TMC2208 or TMC2209 on E5 requires E5_HARDWARE_SERIAL or E5_SERIAL_(RX|TX)_PIN." #error "TMC2208 or TMC2209 on E5 requires E5_HARDWARE_SERIAL or E5_SERIAL_(RX|TX)_PIN."
#elif INVALID_TMC_UART(E6)
#error "TMC2208 or TMC2209 on E6 requires E6_HARDWARE_SERIAL or E6_SERIAL_(RX|TX)_PIN."
#elif INVALID_TMC_UART(E7)
#error "TMC2208 or TMC2209 on E7 requires E7_HARDWARE_SERIAL or E7_SERIAL_(RX|TX)_PIN."
#endif #endif
#undef INVALID_TMC_UART #undef INVALID_TMC_UART
@ -2192,7 +2258,8 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS
|| (IN_CHAIN(Z3) && !PIN_EXISTS(Z3_CS)) || (IN_CHAIN(E0) && !PIN_EXISTS(E0_CS)) \ || (IN_CHAIN(Z3) && !PIN_EXISTS(Z3_CS)) || (IN_CHAIN(E0) && !PIN_EXISTS(E0_CS)) \
|| (IN_CHAIN(E1) && !PIN_EXISTS(E1_CS)) || (IN_CHAIN(E2) && !PIN_EXISTS(E2_CS)) \ || (IN_CHAIN(E1) && !PIN_EXISTS(E1_CS)) || (IN_CHAIN(E2) && !PIN_EXISTS(E2_CS)) \
|| (IN_CHAIN(E3) && !PIN_EXISTS(E3_CS)) || (IN_CHAIN(E4) && !PIN_EXISTS(E4_CS)) \ || (IN_CHAIN(E3) && !PIN_EXISTS(E3_CS)) || (IN_CHAIN(E4) && !PIN_EXISTS(E4_CS)) \
|| (IN_CHAIN(E5) && !PIN_EXISTS(E5_CS)) || (IN_CHAIN(E5) && !PIN_EXISTS(E5_CS)) || (IN_CHAIN(E6) && !PIN_EXISTS(E6_CS)) \
|| (IN_CHAIN(E7) && !PIN_EXISTS(E7_CS))
#error "All chained TMC drivers need a CS pin." #error "All chained TMC drivers need a CS pin."
#else #else
#if IN_CHAIN(X) #if IN_CHAIN(X)
@ -2221,6 +2288,10 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS
#define CS_COMPARE E4_CS_PIN #define CS_COMPARE E4_CS_PIN
#elif IN_CHAIN(E5) #elif IN_CHAIN(E5)
#define CS_COMPARE E5_CS_PIN #define CS_COMPARE E5_CS_PIN
#elif IN_CHAIN(E6)
#define CS_COMPARE E6_CS_PIN
#elif IN_CHAIN(E7)
#define CS_COMPARE E7_CS_PIN
#endif #endif
#if (IN_CHAIN(X) && X_CS_PIN != CS_COMPARE) || (IN_CHAIN(Y) && Y_CS_PIN != CS_COMPARE) \ #if (IN_CHAIN(X) && X_CS_PIN != CS_COMPARE) || (IN_CHAIN(Y) && Y_CS_PIN != CS_COMPARE) \
|| (IN_CHAIN(Z) && Z_CS_PIN != CS_COMPARE) || (IN_CHAIN(X2) && X2_CS_PIN != CS_COMPARE) \ || (IN_CHAIN(Z) && Z_CS_PIN != CS_COMPARE) || (IN_CHAIN(X2) && X2_CS_PIN != CS_COMPARE) \
@ -2228,7 +2299,8 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS
|| (IN_CHAIN(Z3) && Z3_CS_PIN != CS_COMPARE) || (IN_CHAIN(E0) && E0_CS_PIN != CS_COMPARE) \ || (IN_CHAIN(Z3) && Z3_CS_PIN != CS_COMPARE) || (IN_CHAIN(E0) && E0_CS_PIN != CS_COMPARE) \
|| (IN_CHAIN(E1) && E1_CS_PIN != CS_COMPARE) || (IN_CHAIN(E2) && E2_CS_PIN != CS_COMPARE) \ || (IN_CHAIN(E1) && E1_CS_PIN != CS_COMPARE) || (IN_CHAIN(E2) && E2_CS_PIN != CS_COMPARE) \
|| (IN_CHAIN(E3) && E3_CS_PIN != CS_COMPARE) || (IN_CHAIN(E4) && E4_CS_PIN != CS_COMPARE) \ || (IN_CHAIN(E3) && E3_CS_PIN != CS_COMPARE) || (IN_CHAIN(E4) && E4_CS_PIN != CS_COMPARE) \
|| (IN_CHAIN(E5) && E5_CS_PIN != CS_COMPARE) || (IN_CHAIN(E5) && E5_CS_PIN != CS_COMPARE) || (IN_CHAIN(E6) && E6_CS_PIN != CS_COMPARE) \
|| (IN_CHAIN(E7) && E7_CS_PIN != CS_COMPARE)
#error "All chained TMC drivers must use the same CS pin." #error "All chained TMC drivers must use the same CS pin."
#endif #endif
#endif #endif
@ -2521,12 +2593,26 @@ static_assert( _ARR_TEST(3,0) && _ARR_TEST(3,1) && _ARR_TEST(3,2)
#error "SPINDLE_LASER_PWM_PIN conflicts with E4_AUTO_FAN_PIN." #error "SPINDLE_LASER_PWM_PIN conflicts with E4_AUTO_FAN_PIN."
#elif _PIN_CONFLICT(E5_AUTO_FAN) #elif _PIN_CONFLICT(E5_AUTO_FAN)
#error "SPINDLE_LASER_PWM_PIN conflicts with E5_AUTO_FAN_PIN." #error "SPINDLE_LASER_PWM_PIN conflicts with E5_AUTO_FAN_PIN."
#elif _PIN_CONFLICT(E6_AUTO_FAN)
#error "SPINDLE_LASER_PWM_PIN conflicts with E6_AUTO_FAN_PIN."
#elif _PIN_CONFLICT(E7_AUTO_FAN)
#error "SPINDLE_LASER_PWM_PIN conflicts with E7_AUTO_FAN_PIN."
#elif _PIN_CONFLICT(FAN) #elif _PIN_CONFLICT(FAN)
#error "SPINDLE_LASER_PWM_PIN conflicts with FAN_PIN." #error "SPINDLE_LASER_PWM_PIN conflicts with FAN_PIN."
#elif _PIN_CONFLICT(FAN1) #elif _PIN_CONFLICT(FAN1)
#error "SPINDLE_LASER_PWM_PIN conflicts with FAN1_PIN." #error "SPINDLE_LASER_PWM_PIN conflicts with FAN1_PIN."
#elif _PIN_CONFLICT(FAN2) #elif _PIN_CONFLICT(FAN2)
#error "SPINDLE_LASER_PWM_PIN conflicts with FAN2_PIN." #error "SPINDLE_LASER_PWM_PIN conflicts with FAN2_PIN."
#elif _PIN_CONFLICT(FAN3)
#error "SPINDLE_LASER_PWM_PIN conflicts with FAN3_PIN."
#elif _PIN_CONFLICT(FAN4)
#error "SPINDLE_LASER_PWM_PIN conflicts with FAN4_PIN."
#elif _PIN_CONFLICT(FAN5)
#error "SPINDLE_LASER_PWM_PIN conflicts with FAN5_PIN."
#elif _PIN_CONFLICT(FAN6)
#error "SPINDLE_LASER_PWM_PIN conflicts with FAN6_PIN."
#elif _PIN_CONFLICT(FAN7)
#error "SPINDLE_LASER_PWM_PIN conflicts with FAN7_PIN."
#elif _PIN_CONFLICT(CONTROLLERFAN) #elif _PIN_CONFLICT(CONTROLLERFAN)
#error "SPINDLE_LASER_PWM_PIN conflicts with CONTROLLERFAN_PIN." #error "SPINDLE_LASER_PWM_PIN conflicts with CONTROLLERFAN_PIN."
#elif _PIN_CONFLICT(MOTOR_CURRENT_PWM_XY) #elif _PIN_CONFLICT(MOTOR_CURRENT_PWM_XY)

View File

@ -1092,6 +1092,21 @@ void MarlinUI::draw_status_screen() {
#if HAS_FAN2 #if HAS_FAN2
|| thermalManager.fan_speed[2] || thermalManager.fan_speed[2]
#endif #endif
#if HAS_FAN3
|| thermalManager.fan_speed[3]
#endif
#if HAS_FAN4
|| thermalManager.fan_speed[4]
#endif
#if HAS_FAN5
|| thermalManager.fan_speed[5]
#endif
#if HAS_FAN6
|| thermalManager.fan_speed[6]
#endif
#if HAS_FAN7
|| thermalManager.fan_speed[7]
#endif
) leds |= LED_C; ) leds |= LED_C;
#endif // FAN_COUNT > 0 #endif // FAN_COUNT > 0

View File

@ -912,7 +912,7 @@ namespace ExtUI {
#endif #endif
{ {
#if HOTENDS #if HOTENDS
static constexpr int16_t heater_maxtemp[HOTENDS] = ARRAY_BY_HOTENDS(HEATER_0_MAXTEMP, HEATER_1_MAXTEMP, HEATER_2_MAXTEMP, HEATER_3_MAXTEMP, HEATER_4_MAXTEMP, HEATER_5_MAXTEMP); static constexpr int16_t heater_maxtemp[HOTENDS] = ARRAY_BY_HOTENDS(HEATER_0_MAXTEMP, HEATER_1_MAXTEMP, HEATER_2_MAXTEMP, HEATER_3_MAXTEMP, HEATER_4_MAXTEMP, HEATER_5_MAXTEMP, HEATER_6_MAXTEMP, HEATER_7_MAXTEMP);
const int16_t e = heater - H0; const int16_t e = heater - H0;
thermalManager.setTargetHotend(LROUND(constrain(value, 0, heater_maxtemp[e] - 15)), e); thermalManager.setTargetHotend(LROUND(constrain(value, 0, heater_maxtemp[e] - 15)), e);
#endif #endif
@ -924,7 +924,7 @@ namespace ExtUI {
value *= TOUCH_UI_LCD_TEMP_SCALING; value *= TOUCH_UI_LCD_TEMP_SCALING;
#endif #endif
#if HOTENDS #if HOTENDS
constexpr int16_t heater_maxtemp[HOTENDS] = ARRAY_BY_HOTENDS(HEATER_0_MAXTEMP, HEATER_1_MAXTEMP, HEATER_2_MAXTEMP, HEATER_3_MAXTEMP, HEATER_4_MAXTEMP, HEATER_5_MAXTEMP); constexpr int16_t heater_maxtemp[HOTENDS] = ARRAY_BY_HOTENDS(HEATER_0_MAXTEMP, HEATER_1_MAXTEMP, HEATER_2_MAXTEMP, HEATER_3_MAXTEMP, HEATER_4_MAXTEMP, HEATER_5_MAXTEMP, HEATER_6_MAXTEMP, HEATER_7_MAXTEMP);
const int16_t e = extruder - E0; const int16_t e = extruder - E0;
enableHeater(extruder); enableHeater(extruder);
thermalManager.setTargetHotend(LROUND(constrain(value, 0, heater_maxtemp[e] - 15)), e); thermalManager.setTargetHotend(LROUND(constrain(value, 0, heater_maxtemp[e] - 15)), e);

View File

@ -55,7 +55,7 @@ namespace ExtUI {
enum axis_t : uint8_t { X, Y, Z }; enum axis_t : uint8_t { X, Y, Z };
enum extruder_t : uint8_t { E0, E1, E2, E3, E4, E5 }; enum extruder_t : uint8_t { E0, E1, E2, E3, E4, E5 };
enum heater_t : uint8_t { H0, H1, H2, H3, H4, H5, BED, CHAMBER }; enum heater_t : uint8_t { H0, H1, H2, H3, H4, H5, BED, CHAMBER };
enum fan_t : uint8_t { FAN0, FAN1, FAN2, FAN3, FAN4, FAN5 }; enum fan_t : uint8_t { FAN0, FAN1, FAN2, FAN3, FAN4, FAN5, FAN6, FAN7 };
enum result_t : uint8_t { PID_BAD_EXTRUDER_NUM, PID_TEMP_TOO_HIGH, PID_TUNING_TIMEOUT, PID_DONE }; enum result_t : uint8_t { PID_BAD_EXTRUDER_NUM, PID_TEMP_TOO_HIGH, PID_TUNING_TIMEOUT, PID_DONE };
constexpr uint8_t extruderCount = EXTRUDERS; constexpr uint8_t extruderCount = EXTRUDERS;

View File

@ -93,7 +93,7 @@ namespace Language_an {
PROGMEM Language_Str MSG_NOZZLE_N = _UxGT("Boquilla ~"); PROGMEM Language_Str MSG_NOZZLE_N = _UxGT("Boquilla ~");
PROGMEM Language_Str MSG_BED = _UxGT("Base"); PROGMEM Language_Str MSG_BED = _UxGT("Base");
PROGMEM Language_Str MSG_FAN_SPEED = _UxGT("Ixoriador"); PROGMEM Language_Str MSG_FAN_SPEED = _UxGT("Ixoriador");
PROGMEM Language_Str MSG_FAN_SPEED_N = _UxGT("Ixoriador ="); PROGMEM Language_Str MSG_FAN_SPEED_N = _UxGT("Ixoriador ~");
PROGMEM Language_Str MSG_FLOW = _UxGT("Fluxo"); PROGMEM Language_Str MSG_FLOW = _UxGT("Fluxo");
PROGMEM Language_Str MSG_FLOW_N = _UxGT("Fluxo ~"); PROGMEM Language_Str MSG_FLOW_N = _UxGT("Fluxo ~");
PROGMEM Language_Str MSG_CONTROL = _UxGT("Control"); PROGMEM Language_Str MSG_CONTROL = _UxGT("Control");

View File

@ -83,7 +83,7 @@ namespace Language_bg {
PROGMEM Language_Str MSG_NOZZLE_N = " " LCD_STR_THERMOMETER _UxGT(" Дюза ~"); PROGMEM Language_Str MSG_NOZZLE_N = " " LCD_STR_THERMOMETER _UxGT(" Дюза ~");
PROGMEM Language_Str MSG_BED = " " LCD_STR_THERMOMETER _UxGT(" Легло"); PROGMEM Language_Str MSG_BED = " " LCD_STR_THERMOMETER _UxGT(" Легло");
PROGMEM Language_Str MSG_FAN_SPEED = _UxGT("Вентилатор"); PROGMEM Language_Str MSG_FAN_SPEED = _UxGT("Вентилатор");
PROGMEM Language_Str MSG_FAN_SPEED_N = _UxGT("Вентилатор ="); PROGMEM Language_Str MSG_FAN_SPEED_N = _UxGT("Вентилатор ~");
PROGMEM Language_Str MSG_FLOW = _UxGT("Поток"); PROGMEM Language_Str MSG_FLOW = _UxGT("Поток");
PROGMEM Language_Str MSG_FLOW_N = _UxGT("Поток ~"); PROGMEM Language_Str MSG_FLOW_N = _UxGT("Поток ~");
PROGMEM Language_Str MSG_CONTROL = _UxGT("Управление"); PROGMEM Language_Str MSG_CONTROL = _UxGT("Управление");

View File

@ -94,7 +94,7 @@ namespace Language_ca {
PROGMEM Language_Str MSG_NOZZLE_N = _UxGT("Nozzle ~"); PROGMEM Language_Str MSG_NOZZLE_N = _UxGT("Nozzle ~");
PROGMEM Language_Str MSG_BED = _UxGT("Llit"); PROGMEM Language_Str MSG_BED = _UxGT("Llit");
PROGMEM Language_Str MSG_FAN_SPEED = _UxGT("Vel. Ventilador"); PROGMEM Language_Str MSG_FAN_SPEED = _UxGT("Vel. Ventilador");
PROGMEM Language_Str MSG_FAN_SPEED_N = _UxGT("Vel. Ventilador ="); PROGMEM Language_Str MSG_FAN_SPEED_N = _UxGT("Vel. Ventilador ~");
PROGMEM Language_Str MSG_FLOW = _UxGT("Flux"); PROGMEM Language_Str MSG_FLOW = _UxGT("Flux");
PROGMEM Language_Str MSG_FLOW_N = _UxGT("Flux ~"); PROGMEM Language_Str MSG_FLOW_N = _UxGT("Flux ~");
PROGMEM Language_Str MSG_VTRAV_MIN = _UxGT("VViatge min"); PROGMEM Language_Str MSG_VTRAV_MIN = _UxGT("VViatge min");

View File

@ -251,10 +251,10 @@ namespace Language_cz {
PROGMEM Language_Str MSG_BED = _UxGT("Podložka"); PROGMEM Language_Str MSG_BED = _UxGT("Podložka");
PROGMEM Language_Str MSG_CHAMBER = _UxGT("Komora"); PROGMEM Language_Str MSG_CHAMBER = _UxGT("Komora");
PROGMEM Language_Str MSG_FAN_SPEED = _UxGT("Rychlost vent."); PROGMEM Language_Str MSG_FAN_SPEED = _UxGT("Rychlost vent.");
PROGMEM Language_Str MSG_FAN_SPEED_N = _UxGT("Rychlost vent. ="); PROGMEM Language_Str MSG_FAN_SPEED_N = _UxGT("Rychlost vent. ~");
PROGMEM Language_Str MSG_STORED_FAN_N = _UxGT("Ulož. vent. ="); PROGMEM Language_Str MSG_STORED_FAN_N = _UxGT("Ulož. vent. ~");
PROGMEM Language_Str MSG_EXTRA_FAN_SPEED = _UxGT("Rychlost ex. vent."); PROGMEM Language_Str MSG_EXTRA_FAN_SPEED = _UxGT("Rychlost ex. vent.");
PROGMEM Language_Str MSG_EXTRA_FAN_SPEED_N = _UxGT("Rychlost ex. vent. ="); PROGMEM Language_Str MSG_EXTRA_FAN_SPEED_N = _UxGT("Rychlost ex. vent. ~");
PROGMEM Language_Str MSG_FLOW = _UxGT("Průtok"); PROGMEM Language_Str MSG_FLOW = _UxGT("Průtok");
PROGMEM Language_Str MSG_FLOW_N = _UxGT("Průtok ~"); PROGMEM Language_Str MSG_FLOW_N = _UxGT("Průtok ~");
PROGMEM Language_Str MSG_CONTROL = _UxGT("Ovládaní"); PROGMEM Language_Str MSG_CONTROL = _UxGT("Ovládaní");

View File

@ -84,7 +84,7 @@ namespace Language_da {
PROGMEM Language_Str MSG_BED = _UxGT("Plade"); PROGMEM Language_Str MSG_BED = _UxGT("Plade");
PROGMEM Language_Str MSG_FAN_SPEED = _UxGT("Blæser hastighed"); PROGMEM Language_Str MSG_FAN_SPEED = _UxGT("Blæser hastighed");
PROGMEM Language_Str MSG_FAN_SPEED_N = _UxGT("Blæser hastighed ="); PROGMEM Language_Str MSG_FAN_SPEED_N = _UxGT("Blæser hastighed ~");
PROGMEM Language_Str MSG_CONTROL = _UxGT("Kontrol"); PROGMEM Language_Str MSG_CONTROL = _UxGT("Kontrol");
PROGMEM Language_Str MSG_MIN = _UxGT(" \002 Min"); PROGMEM Language_Str MSG_MIN = _UxGT(" \002 Min");
PROGMEM Language_Str MSG_MAX = _UxGT(" \002 Max"); PROGMEM Language_Str MSG_MAX = _UxGT(" \002 Max");

View File

@ -91,7 +91,7 @@ namespace Language_el {
PROGMEM Language_Str MSG_NOZZLE_N = _UxGT("Ακροφύσιο ~"); PROGMEM Language_Str MSG_NOZZLE_N = _UxGT("Ακροφύσιο ~");
PROGMEM Language_Str MSG_BED = _UxGT("Κλίνη"); PROGMEM Language_Str MSG_BED = _UxGT("Κλίνη");
PROGMEM Language_Str MSG_FAN_SPEED = _UxGT("Ταχύτητα ανεμιστήρα"); PROGMEM Language_Str MSG_FAN_SPEED = _UxGT("Ταχύτητα ανεμιστήρα");
PROGMEM Language_Str MSG_FAN_SPEED_N = _UxGT("Ταχύτητα ανεμιστήρα ="); PROGMEM Language_Str MSG_FAN_SPEED_N = _UxGT("Ταχύτητα ανεμιστήρα ~");
PROGMEM Language_Str MSG_FLOW = _UxGT("Ροή"); PROGMEM Language_Str MSG_FLOW = _UxGT("Ροή");
PROGMEM Language_Str MSG_FLOW_N = _UxGT("Ροή ~"); PROGMEM Language_Str MSG_FLOW_N = _UxGT("Ροή ~");
PROGMEM Language_Str MSG_CONTROL = _UxGT("Έλεγχος"); PROGMEM Language_Str MSG_CONTROL = _UxGT("Έλεγχος");

View File

@ -92,7 +92,7 @@ namespace Language_el_gr {
PROGMEM Language_Str MSG_NOZZLE_N = _UxGT("Ακροφύσιο ~"); PROGMEM Language_Str MSG_NOZZLE_N = _UxGT("Ακροφύσιο ~");
PROGMEM Language_Str MSG_BED = _UxGT("Κλίνη"); PROGMEM Language_Str MSG_BED = _UxGT("Κλίνη");
PROGMEM Language_Str MSG_FAN_SPEED = _UxGT("Ταχύτητα ανεμιστήρα"); PROGMEM Language_Str MSG_FAN_SPEED = _UxGT("Ταχύτητα ανεμιστήρα");
PROGMEM Language_Str MSG_FAN_SPEED_N = _UxGT("Ταχύτητα ανεμιστήρα ="); PROGMEM Language_Str MSG_FAN_SPEED_N = _UxGT("Ταχύτητα ανεμιστήρα ~");
PROGMEM Language_Str MSG_FLOW = _UxGT("Ροή"); PROGMEM Language_Str MSG_FLOW = _UxGT("Ροή");
PROGMEM Language_Str MSG_FLOW_N = _UxGT("Ροή ~"); PROGMEM Language_Str MSG_FLOW_N = _UxGT("Ροή ~");
PROGMEM Language_Str MSG_CONTROL = _UxGT("Έλεγχος"); PROGMEM Language_Str MSG_CONTROL = _UxGT("Έλεγχος");

View File

@ -242,10 +242,10 @@ namespace Language_en {
PROGMEM Language_Str MSG_BED = _UxGT("Bed"); PROGMEM Language_Str MSG_BED = _UxGT("Bed");
PROGMEM Language_Str MSG_CHAMBER = _UxGT("Enclosure"); PROGMEM Language_Str MSG_CHAMBER = _UxGT("Enclosure");
PROGMEM Language_Str MSG_FAN_SPEED = _UxGT("Fan Speed"); PROGMEM Language_Str MSG_FAN_SPEED = _UxGT("Fan Speed");
PROGMEM Language_Str MSG_FAN_SPEED_N = _UxGT("Fan Speed ="); PROGMEM Language_Str MSG_FAN_SPEED_N = _UxGT("Fan Speed ~");
PROGMEM Language_Str MSG_STORED_FAN_N = _UxGT("Stored Fan ="); PROGMEM Language_Str MSG_STORED_FAN_N = _UxGT("Stored Fan ~");
PROGMEM Language_Str MSG_EXTRA_FAN_SPEED = _UxGT("Extra Fan Speed"); PROGMEM Language_Str MSG_EXTRA_FAN_SPEED = _UxGT("Extra Fan Speed");
PROGMEM Language_Str MSG_EXTRA_FAN_SPEED_N = _UxGT("Extra Fan Speed ="); PROGMEM Language_Str MSG_EXTRA_FAN_SPEED_N = _UxGT("Extra Fan Speed ~");
PROGMEM Language_Str MSG_FLOW = _UxGT("Flow"); PROGMEM Language_Str MSG_FLOW = _UxGT("Flow");
PROGMEM Language_Str MSG_FLOW_N = _UxGT("Flow ~"); PROGMEM Language_Str MSG_FLOW_N = _UxGT("Flow ~");
PROGMEM Language_Str MSG_CONTROL = _UxGT("Control"); PROGMEM Language_Str MSG_CONTROL = _UxGT("Control");

View File

@ -240,9 +240,9 @@ namespace Language_es {
PROGMEM Language_Str MSG_BED = _UxGT("Cama"); PROGMEM Language_Str MSG_BED = _UxGT("Cama");
PROGMEM Language_Str MSG_CHAMBER = _UxGT("Recinto"); PROGMEM Language_Str MSG_CHAMBER = _UxGT("Recinto");
PROGMEM Language_Str MSG_FAN_SPEED = _UxGT("Ventilador"); PROGMEM Language_Str MSG_FAN_SPEED = _UxGT("Ventilador");
PROGMEM Language_Str MSG_FAN_SPEED_N = _UxGT("Ventilador ="); PROGMEM Language_Str MSG_FAN_SPEED_N = _UxGT("Ventilador ~");
PROGMEM Language_Str MSG_EXTRA_FAN_SPEED = _UxGT("Vel. Ext. ventilador"); PROGMEM Language_Str MSG_EXTRA_FAN_SPEED = _UxGT("Vel. Ext. ventilador");
PROGMEM Language_Str MSG_EXTRA_FAN_SPEED_N = _UxGT("Vel. Ext. ventilador ="); PROGMEM Language_Str MSG_EXTRA_FAN_SPEED_N = _UxGT("Vel. Ext. ventilador ~");
PROGMEM Language_Str MSG_FLOW = _UxGT("Flujo"); PROGMEM Language_Str MSG_FLOW = _UxGT("Flujo");
PROGMEM Language_Str MSG_FLOW_N = _UxGT("Flujo ~"); PROGMEM Language_Str MSG_FLOW_N = _UxGT("Flujo ~");
PROGMEM Language_Str MSG_CONTROL = _UxGT("Control"); PROGMEM Language_Str MSG_CONTROL = _UxGT("Control");

View File

@ -147,9 +147,9 @@ namespace Language_eu {
PROGMEM Language_Str MSG_NOZZLE_N = _UxGT("Pita ~"); PROGMEM Language_Str MSG_NOZZLE_N = _UxGT("Pita ~");
PROGMEM Language_Str MSG_BED = _UxGT("Ohea"); PROGMEM Language_Str MSG_BED = _UxGT("Ohea");
PROGMEM Language_Str MSG_FAN_SPEED = _UxGT("Haizagailu abiadura"); PROGMEM Language_Str MSG_FAN_SPEED = _UxGT("Haizagailu abiadura");
PROGMEM Language_Str MSG_FAN_SPEED_N = _UxGT("Haizagailu abiadura ="); PROGMEM Language_Str MSG_FAN_SPEED_N = _UxGT("Haizagailu abiadura ~");
PROGMEM Language_Str MSG_EXTRA_FAN_SPEED = _UxGT("Haiz.gehig. abiadura"); PROGMEM Language_Str MSG_EXTRA_FAN_SPEED = _UxGT("Haiz.gehig. abiadura");
PROGMEM Language_Str MSG_EXTRA_FAN_SPEED_N = _UxGT("Haiz.gehig. abiadura ="); PROGMEM Language_Str MSG_EXTRA_FAN_SPEED_N = _UxGT("Haiz.gehig. abiadura ~");
PROGMEM Language_Str MSG_FLOW = _UxGT("Fluxua"); PROGMEM Language_Str MSG_FLOW = _UxGT("Fluxua");
PROGMEM Language_Str MSG_FLOW_N = _UxGT("Fluxua ~"); PROGMEM Language_Str MSG_FLOW_N = _UxGT("Fluxua ~");
PROGMEM Language_Str MSG_CONTROL = _UxGT("Kontrola"); PROGMEM Language_Str MSG_CONTROL = _UxGT("Kontrola");

View File

@ -79,7 +79,7 @@ namespace Language_fi {
PROGMEM Language_Str MSG_NOZZLE_N = _UxGT("Suutin ~"); PROGMEM Language_Str MSG_NOZZLE_N = _UxGT("Suutin ~");
PROGMEM Language_Str MSG_BED = _UxGT("Alusta"); PROGMEM Language_Str MSG_BED = _UxGT("Alusta");
PROGMEM Language_Str MSG_FAN_SPEED = _UxGT("Tuul. nopeus"); PROGMEM Language_Str MSG_FAN_SPEED = _UxGT("Tuul. nopeus");
PROGMEM Language_Str MSG_FAN_SPEED_N = _UxGT("Tuul. nopeus ="); PROGMEM Language_Str MSG_FAN_SPEED_N = _UxGT("Tuul. nopeus ~");
PROGMEM Language_Str MSG_FLOW = _UxGT("Virtaus"); PROGMEM Language_Str MSG_FLOW = _UxGT("Virtaus");
PROGMEM Language_Str MSG_FLOW_N = _UxGT("Virtaus ~"); PROGMEM Language_Str MSG_FLOW_N = _UxGT("Virtaus ~");
PROGMEM Language_Str MSG_CONTROL = _UxGT("Kontrolli"); PROGMEM Language_Str MSG_CONTROL = _UxGT("Kontrolli");

View File

@ -235,10 +235,10 @@ namespace Language_fr {
PROGMEM Language_Str MSG_BED = _UxGT("Lit"); PROGMEM Language_Str MSG_BED = _UxGT("Lit");
PROGMEM Language_Str MSG_CHAMBER = _UxGT("Caisson"); PROGMEM Language_Str MSG_CHAMBER = _UxGT("Caisson");
PROGMEM Language_Str MSG_FAN_SPEED = _UxGT("Vit. ventil. "); // 15 car. max PROGMEM Language_Str MSG_FAN_SPEED = _UxGT("Vit. ventil. "); // 15 car. max
PROGMEM Language_Str MSG_FAN_SPEED_N = _UxGT("Vit. ventil. ="); PROGMEM Language_Str MSG_FAN_SPEED_N = _UxGT("Vit. ventil. ~");
PROGMEM Language_Str MSG_STORED_FAN_N = _UxGT("Vit. enreg. ="); PROGMEM Language_Str MSG_STORED_FAN_N = _UxGT("Vit. enreg. ~");
PROGMEM Language_Str MSG_EXTRA_FAN_SPEED = _UxGT("Extra ventil. "); PROGMEM Language_Str MSG_EXTRA_FAN_SPEED = _UxGT("Extra ventil. ");
PROGMEM Language_Str MSG_EXTRA_FAN_SPEED_N = _UxGT("Extra ventil. ="); PROGMEM Language_Str MSG_EXTRA_FAN_SPEED_N = _UxGT("Extra ventil. ~");
PROGMEM Language_Str MSG_FLOW = _UxGT("Flux"); PROGMEM Language_Str MSG_FLOW = _UxGT("Flux");
PROGMEM Language_Str MSG_FLOW_N = _UxGT("Flux ~"); PROGMEM Language_Str MSG_FLOW_N = _UxGT("Flux ~");

View File

@ -240,10 +240,10 @@ namespace Language_it {
PROGMEM Language_Str MSG_BED = _UxGT("Piatto"); PROGMEM Language_Str MSG_BED = _UxGT("Piatto");
PROGMEM Language_Str MSG_CHAMBER = _UxGT("Camera"); PROGMEM Language_Str MSG_CHAMBER = _UxGT("Camera");
PROGMEM Language_Str MSG_FAN_SPEED = _UxGT("Vel. ventola"); // Max 15 characters PROGMEM Language_Str MSG_FAN_SPEED = _UxGT("Vel. ventola"); // Max 15 characters
PROGMEM Language_Str MSG_FAN_SPEED_N = _UxGT("Vel. ventola ="); // Max 15 characters PROGMEM Language_Str MSG_FAN_SPEED_N = _UxGT("Vel. ventola ~"); // Max 15 characters
PROGMEM Language_Str MSG_STORED_FAN_N = _UxGT("Ventola mem. ="); // Max 15 characters PROGMEM Language_Str MSG_STORED_FAN_N = _UxGT("Ventola mem. ~"); // Max 15 characters
PROGMEM Language_Str MSG_EXTRA_FAN_SPEED = _UxGT("Extra vel.vent."); // Max 15 characters PROGMEM Language_Str MSG_EXTRA_FAN_SPEED = _UxGT("Extra vel.vent."); // Max 15 characters
PROGMEM Language_Str MSG_EXTRA_FAN_SPEED_N = _UxGT("Extra v.vent. ="); // Max 15 characters PROGMEM Language_Str MSG_EXTRA_FAN_SPEED_N = _UxGT("Extra v.vent. ~"); // Max 15 characters
PROGMEM Language_Str MSG_FLOW = _UxGT("Flusso"); PROGMEM Language_Str MSG_FLOW = _UxGT("Flusso");
PROGMEM Language_Str MSG_FLOW_N = _UxGT("Flusso ~"); PROGMEM Language_Str MSG_FLOW_N = _UxGT("Flusso ~");
PROGMEM Language_Str MSG_CONTROL = _UxGT("Controllo"); PROGMEM Language_Str MSG_CONTROL = _UxGT("Controllo");

View File

@ -77,9 +77,9 @@ namespace Language_ko_KR {
PROGMEM Language_Str MSG_NOZZLE_N = _UxGT("노즐 ~"); PROGMEM Language_Str MSG_NOZZLE_N = _UxGT("노즐 ~");
PROGMEM Language_Str MSG_BED = _UxGT("베드"); PROGMEM Language_Str MSG_BED = _UxGT("베드");
PROGMEM Language_Str MSG_FAN_SPEED = _UxGT("펜 속도"); PROGMEM Language_Str MSG_FAN_SPEED = _UxGT("펜 속도");
PROGMEM Language_Str MSG_FAN_SPEED_N = _UxGT("펜 속도 ="); PROGMEM Language_Str MSG_FAN_SPEED_N = _UxGT("펜 속도 ~");
PROGMEM Language_Str MSG_EXTRA_FAN_SPEED = _UxGT("엑스트라 펜 속도"); PROGMEM Language_Str MSG_EXTRA_FAN_SPEED = _UxGT("엑스트라 펜 속도");
PROGMEM Language_Str MSG_EXTRA_FAN_SPEED_N = _UxGT("엑스트라 펜 속도 ="); PROGMEM Language_Str MSG_EXTRA_FAN_SPEED_N = _UxGT("엑스트라 펜 속도 ~");
PROGMEM Language_Str MSG_TEMPERATURE = _UxGT("온도"); PROGMEM Language_Str MSG_TEMPERATURE = _UxGT("온도");
PROGMEM Language_Str MSG_MOTION = _UxGT("동작"); PROGMEM Language_Str MSG_MOTION = _UxGT("동작");
PROGMEM Language_Str MSG_STORE_EEPROM = _UxGT("설정 저장하기"); PROGMEM Language_Str MSG_STORE_EEPROM = _UxGT("설정 저장하기");

View File

@ -99,7 +99,7 @@ namespace Language_nl {
PROGMEM Language_Str MSG_NOZZLE_N = _UxGT("Nozzle ~"); PROGMEM Language_Str MSG_NOZZLE_N = _UxGT("Nozzle ~");
PROGMEM Language_Str MSG_BED = _UxGT("Bed"); PROGMEM Language_Str MSG_BED = _UxGT("Bed");
PROGMEM Language_Str MSG_FAN_SPEED = _UxGT("Fan snelheid"); PROGMEM Language_Str MSG_FAN_SPEED = _UxGT("Fan snelheid");
PROGMEM Language_Str MSG_FAN_SPEED_N = _UxGT("Fan snelheid ="); PROGMEM Language_Str MSG_FAN_SPEED_N = _UxGT("Fan snelheid ~");
PROGMEM Language_Str MSG_FLOW = _UxGT("Flow"); PROGMEM Language_Str MSG_FLOW = _UxGT("Flow");
PROGMEM Language_Str MSG_FLOW_N = _UxGT("Flow ~"); PROGMEM Language_Str MSG_FLOW_N = _UxGT("Flow ~");
PROGMEM Language_Str MSG_CONTROL = _UxGT("Control"); PROGMEM Language_Str MSG_CONTROL = _UxGT("Control");

View File

@ -240,9 +240,9 @@ namespace Language_pl {
PROGMEM Language_Str MSG_BED = _UxGT("Stół"); PROGMEM Language_Str MSG_BED = _UxGT("Stół");
PROGMEM Language_Str MSG_CHAMBER = _UxGT("Obudowa"); PROGMEM Language_Str MSG_CHAMBER = _UxGT("Obudowa");
PROGMEM Language_Str MSG_FAN_SPEED = _UxGT("Obroty wiatraka"); PROGMEM Language_Str MSG_FAN_SPEED = _UxGT("Obroty wiatraka");
PROGMEM Language_Str MSG_FAN_SPEED_N = _UxGT("Obroty wiatraka ="); PROGMEM Language_Str MSG_FAN_SPEED_N = _UxGT("Obroty wiatraka ~");
PROGMEM Language_Str MSG_EXTRA_FAN_SPEED = _UxGT("Obroty dodatkowego wiatraka"); PROGMEM Language_Str MSG_EXTRA_FAN_SPEED = _UxGT("Obroty dodatkowego wiatraka");
PROGMEM Language_Str MSG_EXTRA_FAN_SPEED_N = _UxGT("Obroty dodatkowego wiatraka ="); PROGMEM Language_Str MSG_EXTRA_FAN_SPEED_N = _UxGT("Obroty dodatkowego wiatraka ~");
PROGMEM Language_Str MSG_FLOW = _UxGT("Przepływ"); PROGMEM Language_Str MSG_FLOW = _UxGT("Przepływ");
PROGMEM Language_Str MSG_FLOW_N = _UxGT("Przepływ ~"); PROGMEM Language_Str MSG_FLOW_N = _UxGT("Przepływ ~");
PROGMEM Language_Str MSG_CONTROL = _UxGT("Ustawienia"); PROGMEM Language_Str MSG_CONTROL = _UxGT("Ustawienia");

View File

@ -89,7 +89,7 @@ namespace Language_pt {
PROGMEM Language_Str MSG_NOZZLE_N = " " LCD_STR_THERMOMETER _UxGT(" Bico ~"); PROGMEM Language_Str MSG_NOZZLE_N = " " LCD_STR_THERMOMETER _UxGT(" Bico ~");
PROGMEM Language_Str MSG_BED = " " LCD_STR_THERMOMETER _UxGT(" Base"); PROGMEM Language_Str MSG_BED = " " LCD_STR_THERMOMETER _UxGT(" Base");
PROGMEM Language_Str MSG_FAN_SPEED = _UxGT("Vel. ventoinha"); PROGMEM Language_Str MSG_FAN_SPEED = _UxGT("Vel. ventoinha");
PROGMEM Language_Str MSG_FAN_SPEED_N = _UxGT("Vel. ventoinha ="); PROGMEM Language_Str MSG_FAN_SPEED_N = _UxGT("Vel. ventoinha ~");
PROGMEM Language_Str MSG_FLOW = _UxGT("Fluxo"); PROGMEM Language_Str MSG_FLOW = _UxGT("Fluxo");
PROGMEM Language_Str MSG_FLOW_N = _UxGT("Fluxo ~"); PROGMEM Language_Str MSG_FLOW_N = _UxGT("Fluxo ~");
PROGMEM Language_Str MSG_CONTROL = _UxGT("Controlo"); PROGMEM Language_Str MSG_CONTROL = _UxGT("Controlo");

View File

@ -207,9 +207,9 @@ namespace Language_pt_br {
PROGMEM Language_Str MSG_NOZZLE_N = _UxGT("Bocal ~"); PROGMEM Language_Str MSG_NOZZLE_N = _UxGT("Bocal ~");
PROGMEM Language_Str MSG_BED = _UxGT("Mesa"); PROGMEM Language_Str MSG_BED = _UxGT("Mesa");
PROGMEM Language_Str MSG_FAN_SPEED = _UxGT("Vel. Ventoinha"); PROGMEM Language_Str MSG_FAN_SPEED = _UxGT("Vel. Ventoinha");
PROGMEM Language_Str MSG_FAN_SPEED_N = _UxGT("Vel. Ventoinha ="); PROGMEM Language_Str MSG_FAN_SPEED_N = _UxGT("Vel. Ventoinha ~");
PROGMEM Language_Str MSG_EXTRA_FAN_SPEED = _UxGT("+Vel. Ventoinha"); PROGMEM Language_Str MSG_EXTRA_FAN_SPEED = _UxGT("+Vel. Ventoinha");
PROGMEM Language_Str MSG_EXTRA_FAN_SPEED_N = _UxGT("+Vel. Ventoinha ="); PROGMEM Language_Str MSG_EXTRA_FAN_SPEED_N = _UxGT("+Vel. Ventoinha ~");
PROGMEM Language_Str MSG_FLOW = _UxGT("Vazão"); PROGMEM Language_Str MSG_FLOW = _UxGT("Vazão");
PROGMEM Language_Str MSG_FLOW_N = _UxGT("Vazão ~"); PROGMEM Language_Str MSG_FLOW_N = _UxGT("Vazão ~");
PROGMEM Language_Str MSG_CONTROL = _UxGT("Controle"); PROGMEM Language_Str MSG_CONTROL = _UxGT("Controle");

View File

@ -243,9 +243,9 @@ namespace Language_sk {
PROGMEM Language_Str MSG_BED = _UxGT("Podložka"); PROGMEM Language_Str MSG_BED = _UxGT("Podložka");
PROGMEM Language_Str MSG_CHAMBER = _UxGT("Komora"); PROGMEM Language_Str MSG_CHAMBER = _UxGT("Komora");
PROGMEM Language_Str MSG_FAN_SPEED = _UxGT("Rýchlosť vent."); PROGMEM Language_Str MSG_FAN_SPEED = _UxGT("Rýchlosť vent.");
PROGMEM Language_Str MSG_FAN_SPEED_N = _UxGT("Rýchlosť vent. ="); PROGMEM Language_Str MSG_FAN_SPEED_N = _UxGT("Rýchlosť vent. ~");
PROGMEM Language_Str MSG_EXTRA_FAN_SPEED = _UxGT("Rýchlosť ex. vent."); PROGMEM Language_Str MSG_EXTRA_FAN_SPEED = _UxGT("Rýchlosť ex. vent.");
PROGMEM Language_Str MSG_EXTRA_FAN_SPEED_N = _UxGT("Rýchlosť ex. vent. ="); PROGMEM Language_Str MSG_EXTRA_FAN_SPEED_N = _UxGT("Rýchlosť ex. vent. ~");
PROGMEM Language_Str MSG_FLOW = _UxGT("Prietok"); PROGMEM Language_Str MSG_FLOW = _UxGT("Prietok");
PROGMEM Language_Str MSG_FLOW_N = _UxGT("Prietok ~"); PROGMEM Language_Str MSG_FLOW_N = _UxGT("Prietok ~");
PROGMEM Language_Str MSG_CONTROL = _UxGT("Ovládanie"); PROGMEM Language_Str MSG_CONTROL = _UxGT("Ovládanie");

View File

@ -210,9 +210,9 @@ namespace Language_tr {
PROGMEM Language_Str MSG_NOZZLE_N = _UxGT("Nozul ~"); PROGMEM Language_Str MSG_NOZZLE_N = _UxGT("Nozul ~");
PROGMEM Language_Str MSG_BED = _UxGT("Tabla"); PROGMEM Language_Str MSG_BED = _UxGT("Tabla");
PROGMEM Language_Str MSG_FAN_SPEED = _UxGT("Fan Hızı"); PROGMEM Language_Str MSG_FAN_SPEED = _UxGT("Fan Hızı");
PROGMEM Language_Str MSG_FAN_SPEED_N = _UxGT("Fan Hızı ="); PROGMEM Language_Str MSG_FAN_SPEED_N = _UxGT("Fan Hızı ~");
PROGMEM Language_Str MSG_EXTRA_FAN_SPEED = _UxGT("Ekstra Fan Hızı"); PROGMEM Language_Str MSG_EXTRA_FAN_SPEED = _UxGT("Ekstra Fan Hızı");
PROGMEM Language_Str MSG_EXTRA_FAN_SPEED_N = _UxGT("Ekstra Fan Hızı ="); PROGMEM Language_Str MSG_EXTRA_FAN_SPEED_N = _UxGT("Ekstra Fan Hızı ~");
PROGMEM Language_Str MSG_FLOW = _UxGT("Akış"); PROGMEM Language_Str MSG_FLOW = _UxGT("Akış");
PROGMEM Language_Str MSG_FLOW_N = _UxGT("Akış ~"); PROGMEM Language_Str MSG_FLOW_N = _UxGT("Akış ~");
PROGMEM Language_Str MSG_CONTROL = _UxGT("Kontrol"); PROGMEM Language_Str MSG_CONTROL = _UxGT("Kontrol");

View File

@ -92,7 +92,7 @@ namespace Language_uk {
PROGMEM Language_Str MSG_NOZZLE_N = _UxGT("Сопло ~"); PROGMEM Language_Str MSG_NOZZLE_N = _UxGT("Сопло ~");
PROGMEM Language_Str MSG_BED = _UxGT("Стіл"); PROGMEM Language_Str MSG_BED = _UxGT("Стіл");
PROGMEM Language_Str MSG_FAN_SPEED = _UxGT("Охолодж."); PROGMEM Language_Str MSG_FAN_SPEED = _UxGT("Охолодж.");
PROGMEM Language_Str MSG_FAN_SPEED_N = _UxGT("Охолодж. ="); PROGMEM Language_Str MSG_FAN_SPEED_N = _UxGT("Охолодж. ~");
PROGMEM Language_Str MSG_FLOW = _UxGT("Потік"); PROGMEM Language_Str MSG_FLOW = _UxGT("Потік");
PROGMEM Language_Str MSG_FLOW_N = _UxGT("Потік ~"); PROGMEM Language_Str MSG_FLOW_N = _UxGT("Потік ~");
PROGMEM Language_Str MSG_CONTROL = _UxGT("Налаштування"); PROGMEM Language_Str MSG_CONTROL = _UxGT("Налаштування");

View File

@ -210,9 +210,9 @@ namespace Language_vi {
PROGMEM Language_Str MSG_NOZZLE_N = _UxGT("Đầu phun ~"); // Nozzle PROGMEM Language_Str MSG_NOZZLE_N = _UxGT("Đầu phun ~"); // Nozzle
PROGMEM Language_Str MSG_BED = _UxGT("Bàn"); // bed PROGMEM Language_Str MSG_BED = _UxGT("Bàn"); // bed
PROGMEM Language_Str MSG_FAN_SPEED = _UxGT("Tốc độ quạt"); // fan speed PROGMEM Language_Str MSG_FAN_SPEED = _UxGT("Tốc độ quạt"); // fan speed
PROGMEM Language_Str MSG_FAN_SPEED_N = _UxGT("Tốc độ quạt ="); // fan speed PROGMEM Language_Str MSG_FAN_SPEED_N = _UxGT("Tốc độ quạt ~"); // fan speed
PROGMEM Language_Str MSG_EXTRA_FAN_SPEED = _UxGT("Tốc độ quạt phụ"); // Extra fan speed PROGMEM Language_Str MSG_EXTRA_FAN_SPEED = _UxGT("Tốc độ quạt phụ"); // Extra fan speed
PROGMEM Language_Str MSG_EXTRA_FAN_SPEED_N = _UxGT("Tốc độ quạt phụ ="); // Extra fan speed PROGMEM Language_Str MSG_EXTRA_FAN_SPEED_N = _UxGT("Tốc độ quạt phụ ~"); // Extra fan speed
PROGMEM Language_Str MSG_FLOW = _UxGT("Lưu Lượng"); PROGMEM Language_Str MSG_FLOW = _UxGT("Lưu Lượng");
PROGMEM Language_Str MSG_FLOW_N = _UxGT("Lưu Lượng ~"); PROGMEM Language_Str MSG_FLOW_N = _UxGT("Lưu Lượng ~");
PROGMEM Language_Str MSG_CONTROL = _UxGT("Điều khiển"); // Control PROGMEM Language_Str MSG_CONTROL = _UxGT("Điều khiển"); // Control

View File

@ -187,9 +187,9 @@ namespace Language_zh_CN {
PROGMEM Language_Str MSG_NOZZLE_N = " " LCD_STR_THERMOMETER _UxGT(" 喷嘴 ~"); //"Nozzle" 噴嘴 PROGMEM Language_Str MSG_NOZZLE_N = " " LCD_STR_THERMOMETER _UxGT(" 喷嘴 ~"); //"Nozzle" 噴嘴
PROGMEM Language_Str MSG_BED = " " LCD_STR_THERMOMETER _UxGT(" 热床"); //"Bed" PROGMEM Language_Str MSG_BED = " " LCD_STR_THERMOMETER _UxGT(" 热床"); //"Bed"
PROGMEM Language_Str MSG_FAN_SPEED = _UxGT("风扇速率"); //"Fan speed" PROGMEM Language_Str MSG_FAN_SPEED = _UxGT("风扇速率"); //"Fan speed"
PROGMEM Language_Str MSG_FAN_SPEED_N = _UxGT("风扇速率 ="); //"Fan speed" PROGMEM Language_Str MSG_FAN_SPEED_N = _UxGT("风扇速率 ~"); //"Fan speed"
PROGMEM Language_Str MSG_EXTRA_FAN_SPEED = _UxGT("额外风扇速率"); // "Extra fan speed" PROGMEM Language_Str MSG_EXTRA_FAN_SPEED = _UxGT("额外风扇速率"); // "Extra fan speed"
PROGMEM Language_Str MSG_EXTRA_FAN_SPEED_N = _UxGT("额外风扇速率 ="); // "Extra fan speed" PROGMEM Language_Str MSG_EXTRA_FAN_SPEED_N = _UxGT("额外风扇速率 ~"); // "Extra fan speed"
PROGMEM Language_Str MSG_FLOW = _UxGT("挤出速率"); //"Flow" PROGMEM Language_Str MSG_FLOW = _UxGT("挤出速率"); //"Flow"
PROGMEM Language_Str MSG_FLOW_N = _UxGT("挤出速率 ~"); //"Flow" PROGMEM Language_Str MSG_FLOW_N = _UxGT("挤出速率 ~"); //"Flow"
PROGMEM Language_Str MSG_CONTROL = _UxGT("控制"); //"Control" PROGMEM Language_Str MSG_CONTROL = _UxGT("控制"); //"Control"

View File

@ -187,9 +187,9 @@ namespace Language_zh_TW {
PROGMEM Language_Str MSG_NOZZLE_N = " " LCD_STR_THERMOMETER _UxGT(" 噴嘴 ~"); PROGMEM Language_Str MSG_NOZZLE_N = " " LCD_STR_THERMOMETER _UxGT(" 噴嘴 ~");
PROGMEM Language_Str MSG_BED = " " LCD_STR_THERMOMETER _UxGT(" 熱床"); //"Bed" PROGMEM Language_Str MSG_BED = " " LCD_STR_THERMOMETER _UxGT(" 熱床"); //"Bed"
PROGMEM Language_Str MSG_FAN_SPEED = _UxGT("風扇速率"); //"Fan speed" PROGMEM Language_Str MSG_FAN_SPEED = _UxGT("風扇速率"); //"Fan speed"
PROGMEM Language_Str MSG_FAN_SPEED_N = _UxGT("風扇速率 ="); PROGMEM Language_Str MSG_FAN_SPEED_N = _UxGT("風扇速率 ~");
PROGMEM Language_Str MSG_EXTRA_FAN_SPEED = _UxGT("額外風扇速率"); // "Extra fan speed" PROGMEM Language_Str MSG_EXTRA_FAN_SPEED = _UxGT("額外風扇速率"); // "Extra fan speed"
PROGMEM Language_Str MSG_EXTRA_FAN_SPEED_N = _UxGT("額外風扇速率 ="); PROGMEM Language_Str MSG_EXTRA_FAN_SPEED_N = _UxGT("額外風扇速率 ~");
PROGMEM Language_Str MSG_FLOW = _UxGT("擠出速率"); PROGMEM Language_Str MSG_FLOW = _UxGT("擠出速率");
PROGMEM Language_Str MSG_FLOW_N = _UxGT("擠出速率 ~"); //"Flow" PROGMEM Language_Str MSG_FLOW_N = _UxGT("擠出速率 ~"); //"Flow"
PROGMEM Language_Str MSG_CONTROL = _UxGT("控制"); //"Control" PROGMEM Language_Str MSG_CONTROL = _UxGT("控制"); //"Control"

View File

@ -30,7 +30,7 @@
extern int8_t encoderLine, encoderTopLine, screen_items; extern int8_t encoderLine, encoderTopLine, screen_items;
#if HOTENDS #if HOTENDS
constexpr int16_t heater_maxtemp[HOTENDS] = ARRAY_BY_HOTENDS(HEATER_0_MAXTEMP, HEATER_1_MAXTEMP, HEATER_2_MAXTEMP, HEATER_3_MAXTEMP, HEATER_4_MAXTEMP, HEATER_5_MAXTEMP); constexpr int16_t heater_maxtemp[HOTENDS] = ARRAY_BY_HOTENDS(HEATER_0_MAXTEMP, HEATER_1_MAXTEMP, HEATER_2_MAXTEMP, HEATER_3_MAXTEMP, HEATER_4_MAXTEMP, HEATER_5_MAXTEMP, HEATER_6_MAXTEMP, HEATER_7_MAXTEMP);
#endif #endif
void scroll_screen(const uint8_t limit, const bool is_menu); void scroll_screen(const uint8_t limit, const bool is_menu);

View File

@ -245,6 +245,12 @@ void menu_cancelobject();
DEFINE_PIDTEMP_FUNCS(4); DEFINE_PIDTEMP_FUNCS(4);
#if HOTENDS > 5 #if HOTENDS > 5
DEFINE_PIDTEMP_FUNCS(5); DEFINE_PIDTEMP_FUNCS(5);
#if HOTENDS > 6
DEFINE_PIDTEMP_FUNCS(6);
#if HOTENDS > 7
DEFINE_PIDTEMP_FUNCS(7);
#endif // HOTENDS > 7
#endif // HOTENDS > 6
#endif // HOTENDS > 5 #endif // HOTENDS > 5
#endif // HOTENDS > 4 #endif // HOTENDS > 4
#endif // HOTENDS > 3 #endif // HOTENDS > 3
@ -330,6 +336,12 @@ void menu_cancelobject();
PID_EDIT_MENU_ITEMS(4); PID_EDIT_MENU_ITEMS(4);
#if HOTENDS > 5 #if HOTENDS > 5
PID_EDIT_MENU_ITEMS(5); PID_EDIT_MENU_ITEMS(5);
#if HOTENDS > 6
PID_EDIT_MENU_ITEMS(6);
#if HOTENDS > 7
PID_EDIT_MENU_ITEMS(7);
#endif // HOTENDS > 7
#endif // HOTENDS > 6
#endif // HOTENDS > 5 #endif // HOTENDS > 5
#endif // HOTENDS > 4 #endif // HOTENDS > 4
#endif // HOTENDS > 3 #endif // HOTENDS > 3

View File

@ -152,6 +152,24 @@ void menu_info_thermistors() {
VALUE_ITEM_P(MSG_INFO_MAX_TEMP, STRINGIFY(HEATER_5_MAXTEMP), SS_LEFT); VALUE_ITEM_P(MSG_INFO_MAX_TEMP, STRINGIFY(HEATER_5_MAXTEMP), SS_LEFT);
#endif #endif
#if TEMP_SENSOR_6 != 0
#undef THERMISTOR_ID
#define THERMISTOR_ID TEMP_SENSOR_6
#include "../thermistornames.h"
STATIC_ITEM_P(PSTR(LCD_STR_E6 ": " THERMISTOR_NAME), SS_INVERT);
VALUE_ITEM_P(MSG_INFO_MIN_TEMP, STRINGIFY(HEATER_6_MINTEMP), SS_LEFT);
VALUE_ITEM_P(MSG_INFO_MAX_TEMP, STRINGIFY(HEATER_6_MAXTEMP), SS_LEFT);
#endif
#if TEMP_SENSOR_7 != 0
#undef THERMISTOR_ID
#define THERMISTOR_ID TEMP_SENSOR_7
#include "../thermistornames.h"
STATIC_ITEM_P(PSTR(LCD_STR_E7 ": " THERMISTOR_NAME), SS_INVERT);
VALUE_ITEM_P(MSG_INFO_MIN_TEMP, STRINGIFY(HEATER_7_MINTEMP), SS_LEFT);
VALUE_ITEM_P(MSG_INFO_MAX_TEMP, STRINGIFY(HEATER_7_MAXTEMP), SS_LEFT);
#endif
#if EXTRUDERS #if EXTRUDERS
{ {
STATIC_ITEM( STATIC_ITEM(

View File

@ -198,33 +198,72 @@ void menu_temperature() {
// Fan Speed: // Fan Speed:
// //
#if FAN_COUNT > 0 #if FAN_COUNT > 0
auto on_fan_update = []{
thermalManager.set_fan_speed(MenuItemBase::itemIndex, editable.uint8);
};
#if HAS_FAN1 || HAS_FAN2 || HAS_FAN3 || HAS_FAN4 || HAS_FAN5 || HAS_FAN6 || HAS_FAN7
auto fan_edit_items = [&](const uint8_t f) {
editable.uint8 = thermalManager.fan_speed[f];
EDIT_ITEM_FAST_N(percent, f, MSG_FAN_SPEED_N, &editable.uint8, 0, 255, on_fan_update);
#if ENABLED(EXTRA_FAN_SPEED)
EDIT_ITEM_FAST_N(percent, f, MSG_EXTRA_FAN_SPEED_N, &thermalManager.new_fan_speed[f], 3, 255);
#endif
};
#endif
#define SNFAN(N) (ENABLED(SINGLENOZZLE) && !HAS_FAN##N && EXTRUDERS > N)
#if SNFAN(1) || SNFAN(2) || SNFAN(3) || SNFAN(4) || SNFAN(5) || SNFAN(6) || SNFAN(7)
auto singlenozzle_item = [&](const uint8_t f) {
editable.uint8 = thermalManager.fan_speed[f];
EDIT_ITEM_FAST_N(percent, f, MSG_STORED_FAN_N, &editable.uint8, 0, 255, on_fan_update);
};
#endif
#if HAS_FAN0 #if HAS_FAN0
editable.uint8 = thermalManager.fan_speed[0]; editable.uint8 = thermalManager.fan_speed[0];
EDIT_ITEM_FAST_N(percent, 1, MSG_FIRST_FAN_SPEED, &editable.uint8, 0, 255, []{ thermalManager.set_fan_speed(0, editable.uint8); }); EDIT_ITEM_FAST_N(percent, 0, MSG_FIRST_FAN_SPEED, &editable.uint8, 0, 255, on_fan_update);
#if ENABLED(EXTRA_FAN_SPEED) #if ENABLED(EXTRA_FAN_SPEED)
EDIT_ITEM_FAST_N(percent, 1, MSG_FIRST_EXTRA_FAN_SPEED, &thermalManager.new_fan_speed[0], 3, 255); EDIT_ITEM_FAST_N(percent, 0, MSG_FIRST_EXTRA_FAN_SPEED, &thermalManager.new_fan_speed[0], 3, 255);
#endif #endif
#endif #endif
#if HAS_FAN1 #if HAS_FAN1
editable.uint8 = thermalManager.fan_speed[1]; fan_edit_items(1);
EDIT_ITEM_FAST_N(percent, 2, MSG_FAN_SPEED_N, &editable.uint8, 0, 255, []{ thermalManager.set_fan_speed(1, editable.uint8); }); #elif SNFAN(1)
#if ENABLED(EXTRA_FAN_SPEED) singlenozzle_item(1);
EDIT_ITEM_FAST_N(percent, 2, MSG_EXTRA_FAN_SPEED_N, &thermalManager.new_fan_speed[1], 3, 255);
#endif
#elif ENABLED(SINGLENOZZLE) && EXTRUDERS > 1
editable.uint8 = thermalManager.fan_speed[1];
EDIT_ITEM_FAST_N(percent, 2, MSG_STORED_FAN_N, &editable.uint8, 0, 255, []{ thermalManager.set_fan_speed(1, editable.uint8); });
#endif #endif
#if HAS_FAN2 #if HAS_FAN2
editable.uint8 = thermalManager.fan_speed[2]; fan_edit_items(2);
EDIT_ITEM_FAST_N(percent, 3, MSG_FAN_SPEED_N, &editable.uint8, 0, 255, []{ thermalManager.set_fan_speed(2, editable.uint8); }); #elif SNFAN(2)
#if ENABLED(EXTRA_FAN_SPEED) singlenozzle_item(1);
EDIT_ITEM_FAST_N(percent, 3, MSG_EXTRA_FAN_SPEED_N, &thermalManager.new_fan_speed[2], 3, 255);
#endif #endif
#elif ENABLED(SINGLENOZZLE) && EXTRUDERS > 2 #if HAS_FAN3
editable.uint8 = thermalManager.fan_speed[2]; fan_edit_items(3);
EDIT_ITEM_FAST_N(percent, 3, MSG_STORED_FAN_N, &editable.uint8, 0, 255, []{ thermalManager.set_fan_speed(2, editable.uint8); }); #elif SNFAN(3)
singlenozzle_item(1);
#endif #endif
#if HAS_FAN4
fan_edit_items(4);
#elif SNFAN(4)
singlenozzle_item(1);
#endif
#if HAS_FAN5
fan_edit_items(5);
#elif SNFAN(5)
singlenozzle_item(1);
#endif
#if HAS_FAN6
fan_edit_items(6);
#elif SNFAN(6)
singlenozzle_item(1);
#endif
#if HAS_FAN7
fan_edit_items(7);
#elif SNFAN(7)
singlenozzle_item(1);
#endif
#endif // FAN_COUNT > 0 #endif // FAN_COUNT > 0
#if HAS_TEMP_HOTEND #if HAS_TEMP_HOTEND
@ -232,7 +271,7 @@ void menu_temperature() {
// //
// Preheat for Material 1 and 2 // Preheat for Material 1 and 2
// //
#if TEMP_SENSOR_1 != 0 || TEMP_SENSOR_2 != 0 || TEMP_SENSOR_3 != 0 || TEMP_SENSOR_4 != 0 || TEMP_SENSOR_5 != 0 || HAS_HEATED_BED #if TEMP_SENSOR_1 != 0 || TEMP_SENSOR_2 != 0 || TEMP_SENSOR_3 != 0 || TEMP_SENSOR_4 != 0 || TEMP_SENSOR_5 != 0 || TEMP_SENSOR_6 != 0 || TEMP_SENSOR_7 != 0 || HAS_HEATED_BED
SUBMENU(MSG_PREHEAT_1, menu_preheat_m1); SUBMENU(MSG_PREHEAT_1, menu_preheat_m1);
SUBMENU(MSG_PREHEAT_2, menu_preheat_m2); SUBMENU(MSG_PREHEAT_2, menu_preheat_m2);
#else #else

View File

@ -79,6 +79,12 @@ void menu_tmc_current() {
#if AXIS_IS_TMC(E5) #if AXIS_IS_TMC(E5)
TMC_EDIT_STORED_I_RMS(E5, LCD_STR_E5); TMC_EDIT_STORED_I_RMS(E5, LCD_STR_E5);
#endif #endif
#if AXIS_IS_TMC(E6)
TMC_EDIT_STORED_I_RMS(E6, LCD_STR_E6);
#endif
#if AXIS_IS_TMC(E7)
TMC_EDIT_STORED_I_RMS(E7, LCD_STR_E7);
#endif
END_MENU(); END_MENU();
} }
@ -131,6 +137,12 @@ void menu_tmc_current() {
#if AXIS_HAS_STEALTHCHOP(E5) #if AXIS_HAS_STEALTHCHOP(E5)
TMC_EDIT_STORED_HYBRID_THRS(E5, LCD_STR_E5); TMC_EDIT_STORED_HYBRID_THRS(E5, LCD_STR_E5);
#endif #endif
#if AXIS_HAS_STEALTHCHOP(E6)
TMC_EDIT_STORED_HYBRID_THRS(E6, LCD_STR_E6);
#endif
#if AXIS_HAS_STEALTHCHOP(E7)
TMC_EDIT_STORED_HYBRID_THRS(E7, LCD_STR_E7);
#endif
END_MENU(); END_MENU();
} }
@ -210,6 +222,12 @@ void menu_tmc_current() {
#if AXIS_HAS_STEALTHCHOP(E5) #if AXIS_HAS_STEALTHCHOP(E5)
TMC_EDIT_STEP_MODE(E5, LCD_STR_E5); TMC_EDIT_STEP_MODE(E5, LCD_STR_E5);
#endif #endif
#if AXIS_HAS_STEALTHCHOP(E6)
TMC_EDIT_STEP_MODE(E6, LCD_STR_E6);
#endif
#if AXIS_HAS_STEALTHCHOP(E7)
TMC_EDIT_STEP_MODE(E7, LCD_STR_E7);
#endif
END_MENU(); END_MENU();
} }

View File

@ -147,33 +147,72 @@ void menu_tune() {
// Fan Speed: // Fan Speed:
// //
#if FAN_COUNT > 0 #if FAN_COUNT > 0
auto on_fan_update = []{
thermalManager.set_fan_speed(MenuItemBase::itemIndex, editable.uint8);
};
#if HAS_FAN1 || HAS_FAN2 || HAS_FAN3 || HAS_FAN4 || HAS_FAN5 || HAS_FAN6 || HAS_FAN7
auto fan_edit_items = [&](const uint8_t f) {
editable.uint8 = thermalManager.fan_speed[f];
EDIT_ITEM_FAST_N(percent, f, MSG_FAN_SPEED_N, &editable.uint8, 0, 255, on_fan_update);
#if ENABLED(EXTRA_FAN_SPEED)
EDIT_ITEM_FAST_N(percent, f, MSG_EXTRA_FAN_SPEED_N, &thermalManager.new_fan_speed[f], 3, 255);
#endif
};
#endif
#define SNFAN(N) (ENABLED(SINGLENOZZLE) && !HAS_FAN##N && EXTRUDERS > N)
#if SNFAN(1) || SNFAN(2) || SNFAN(3) || SNFAN(4) || SNFAN(5) || SNFAN(6) || SNFAN(7)
auto singlenozzle_item = [&](const uint8_t f) {
editable.uint8 = thermalManager.fan_speed[f];
EDIT_ITEM_FAST_N(percent, f, MSG_STORED_FAN_N, &editable.uint8, 0, 255, on_fan_update);
};
#endif
#if HAS_FAN0 #if HAS_FAN0
editable.uint8 = thermalManager.fan_speed[0]; editable.uint8 = thermalManager.fan_speed[0];
EDIT_ITEM_FAST_N(percent, 1, MSG_FIRST_FAN_SPEED, &editable.uint8, 0, 255, []{ thermalManager.set_fan_speed(0, editable.uint8); }); EDIT_ITEM_FAST_N(percent, 0, MSG_FIRST_FAN_SPEED, &editable.uint8, 0, 255, on_fan_update);
#if ENABLED(EXTRA_FAN_SPEED) #if ENABLED(EXTRA_FAN_SPEED)
EDIT_ITEM_FAST_N(percent, 1, MSG_FIRST_EXTRA_FAN_SPEED, &thermalManager.new_fan_speed[0], 3, 255); EDIT_ITEM_FAST_N(percent, 0, MSG_FIRST_EXTRA_FAN_SPEED, &thermalManager.new_fan_speed[0], 3, 255);
#endif #endif
#endif #endif
#if HAS_FAN1 #if HAS_FAN1
editable.uint8 = thermalManager.fan_speed[1]; fan_edit_items(1);
EDIT_ITEM_FAST_N(percent, 2, MSG_FAN_SPEED_N, &editable.uint8, 0, 255, []{ thermalManager.set_fan_speed(1, editable.uint8); }); #elif SNFAN(1)
#if ENABLED(EXTRA_FAN_SPEED) singlenozzle_item(1);
EDIT_ITEM_FAST_N(percent, 2, MSG_EXTRA_FAN_SPEED_N, &thermalManager.new_fan_speed[1], 3, 255);
#endif
#elif ENABLED(SINGLENOZZLE) && EXTRUDERS > 1
editable.uint8 = thermalManager.fan_speed[1];
EDIT_ITEM_FAST_N(percent, 2, MSG_STORED_FAN_N, &editable.uint8, 0, 255, []{ thermalManager.set_fan_speed(1, editable.uint8); });
#endif #endif
#if HAS_FAN2 #if HAS_FAN2
editable.uint8 = thermalManager.fan_speed[2]; fan_edit_items(2);
EDIT_ITEM_FAST_N(percent, 3, MSG_FAN_SPEED_N, &editable.uint8, 0, 255, []{ thermalManager.set_fan_speed(2, editable.uint8); }); #elif SNFAN(2)
#if ENABLED(EXTRA_FAN_SPEED) singlenozzle_item(1);
EDIT_ITEM_FAST_N(percent, 3, MSG_EXTRA_FAN_SPEED_N, &thermalManager.new_fan_speed[2], 3, 255);
#endif #endif
#elif ENABLED(SINGLENOZZLE) && EXTRUDERS > 2 #if HAS_FAN3
editable.uint8 = thermalManager.fan_speed[2]; fan_edit_items(3);
EDIT_ITEM_FAST_N(percent, 3, MSG_STORED_FAN_N, &editable.uint8, 0, 255, []{ thermalManager.set_fan_speed(2, editable.uint8); }); #elif SNFAN(3)
singlenozzle_item(1);
#endif #endif
#if HAS_FAN4
fan_edit_items(4);
#elif SNFAN(4)
singlenozzle_item(1);
#endif
#if HAS_FAN5
fan_edit_items(5);
#elif SNFAN(5)
singlenozzle_item(1);
#endif
#if HAS_FAN6
fan_edit_items(6);
#elif SNFAN(6)
singlenozzle_item(1);
#endif
#if HAS_FAN7
fan_edit_items(7);
#elif SNFAN(7)
singlenozzle_item(1);
#endif
#endif // FAN_COUNT > 0 #endif // FAN_COUNT > 0
// //

View File

@ -39,7 +39,7 @@ L64XX_Marlin L64xxManager;
void echo_yes_no(const bool yes) { serialprintPGM(yes ? PSTR(" YES") : PSTR(" NO ")); } void echo_yes_no(const bool yes) { serialprintPGM(yes ? PSTR(" YES") : PSTR(" NO ")); }
char L64XX_Marlin::index_to_axis[MAX_L64XX][3] = { "X ", "Y ", "Z ", "X2", "Y2", "Z2", "Z3", "Z4", "E0", "E1", "E2", "E3", "E4", "E5" }; char L64XX_Marlin::index_to_axis[MAX_L64XX][3] = { "X ", "Y ", "Z ", "X2", "Y2", "Z2", "Z3", "Z4", "E0", "E1", "E2", "E3", "E4", "E5", "E6", "E7" };
#define DEBUG_OUT ENABLED(L6470_CHITCHAT) #define DEBUG_OUT ENABLED(L6470_CHITCHAT)
#include "../../core/debug_out.h" #include "../../core/debug_out.h"
@ -69,6 +69,8 @@ uint8_t L64XX_Marlin::index_to_dir[MAX_L64XX] = { (INVERT_X_DIR),
(INVERT_E3_DIR), // 11 E3 (INVERT_E3_DIR), // 11 E3
(INVERT_E4_DIR), // 12 E4 (INVERT_E4_DIR), // 12 E4
(INVERT_E5_DIR), // 13 E5 (INVERT_E5_DIR), // 13 E5
(INVERT_E6_DIR), // 14 E6
(INVERT_E7_DIR) // 15 E7
}; };
volatile uint8_t L64XX_Marlin::spi_abort = false; volatile uint8_t L64XX_Marlin::spi_abort = false;

View File

@ -35,7 +35,7 @@
#define dSPIN_STEP_CLOCK_REV dSPIN_STEP_CLOCK+1 #define dSPIN_STEP_CLOCK_REV dSPIN_STEP_CLOCK+1
#define HAS_L64XX_EXTRUDER (AXIS_IS_L64XX(E0) || AXIS_IS_L64XX(E1) || AXIS_IS_L64XX(E2) || AXIS_IS_L64XX(E3) || AXIS_IS_L64XX(E4) || AXIS_IS_L64XX(E5)) #define HAS_L64XX_EXTRUDER (AXIS_IS_L64XX(E0) || AXIS_IS_L64XX(E1) || AXIS_IS_L64XX(E2) || AXIS_IS_L64XX(E3) || AXIS_IS_L64XX(E4) || AXIS_IS_L64XX(E5))
enum L64XX_axis_t : uint8_t { X, Y, Z, X2, Y2, Z2, Z3, Z4, E0, E1, E2, E3, E4, E5, MAX_L64XX }; enum L64XX_axis_t : uint8_t { X, Y, Z, X2, Y2, Z2, Z3, Z4, E0, E1, E2, E3, E4, E5, E6, E7, MAX_L64XX };
class L64XX_Marlin : public L64XXHelper { class L64XX_Marlin : public L64XXHelper {
public: public:

View File

@ -66,7 +66,7 @@
* @return value read * @return value read
*/ */
FORCE_INLINE static bool fastDigitalRead(uint8_t pin) { FORCE_INLINE static bool fastDigitalRead(uint8_t pin) {
return g_APinDescription[pin].pPort->PIO_PDSR & g_APinDescription[pin].ulPin; return digitalRead(pin);
} }
/** /**
@ -75,10 +75,7 @@
* @param[in] level value to write * @param[in] level value to write
*/ */
FORCE_INLINE static void fastDigitalWrite(uint8_t pin, bool value) { FORCE_INLINE static void fastDigitalWrite(uint8_t pin, bool value) {
if (value) digitalWrite(pin, value);
g_APinDescription[pin].pPort->PIO_SODR = g_APinDescription[pin].ulPin;
else
g_APinDescription[pin].pPort->PIO_CODR = g_APinDescription[pin].ulPin;
} }
#endif // !CORE_TEENSY #endif // !CORE_TEENSY

View File

@ -1008,6 +1008,16 @@ void MarlinSettings::postprocess() {
#if AXIS_IS_TMC(E5) #if AXIS_IS_TMC(E5)
tmc_stepper_current.E5 = stepperE5.getMilliamps(); tmc_stepper_current.E5 = stepperE5.getMilliamps();
#endif #endif
#if MAX_EXTRUDERS > 6
#if AXIS_IS_TMC(E6)
tmc_stepper_current.E6 = stepperE6.getMilliamps();
#endif
#if MAX_EXTRUDERS > 7
#if AXIS_IS_TMC(E7)
tmc_stepper_current.E7 = stepperE7.getMilliamps();
#endif
#endif // MAX_EXTRUDERS > 7
#endif // MAX_EXTRUDERS > 6
#endif // MAX_EXTRUDERS > 5 #endif // MAX_EXTRUDERS > 5
#endif // MAX_EXTRUDERS > 4 #endif // MAX_EXTRUDERS > 4
#endif // MAX_EXTRUDERS > 3 #endif // MAX_EXTRUDERS > 3
@ -1074,6 +1084,16 @@ void MarlinSettings::postprocess() {
#if AXIS_HAS_STEALTHCHOP(E5) #if AXIS_HAS_STEALTHCHOP(E5)
tmc_hybrid_threshold.E5 = stepperE5.get_pwm_thrs(); tmc_hybrid_threshold.E5 = stepperE5.get_pwm_thrs();
#endif #endif
#if MAX_EXTRUDERS > 6
#if AXIS_HAS_STEALTHCHOP(E6)
tmc_hybrid_threshold.E6 = stepperE6.get_pwm_thrs();
#endif
#if MAX_EXTRUDERS > 7
#if AXIS_HAS_STEALTHCHOP(E7)
tmc_hybrid_threshold.E7 = stepperE7.get_pwm_thrs();
#endif
#endif // MAX_EXTRUDERS > 7
#endif // MAX_EXTRUDERS > 6
#endif // MAX_EXTRUDERS > 5 #endif // MAX_EXTRUDERS > 5
#endif // MAX_EXTRUDERS > 4 #endif // MAX_EXTRUDERS > 4
#endif // MAX_EXTRUDERS > 3 #endif // MAX_EXTRUDERS > 3
@ -1170,6 +1190,16 @@ void MarlinSettings::postprocess() {
#if AXIS_HAS_STEALTHCHOP(E5) #if AXIS_HAS_STEALTHCHOP(E5)
tmc_stealth_enabled.E5 = stepperE5.get_stealthChop_status(); tmc_stealth_enabled.E5 = stepperE5.get_stealthChop_status();
#endif #endif
#if MAX_EXTRUDERS > 6
#if AXIS_HAS_STEALTHCHOP(E6)
tmc_stealth_enabled.E6 = stepperE6.get_stealthChop_status();
#endif
#if MAX_EXTRUDERS > 7
#if AXIS_HAS_STEALTHCHOP(E7)
tmc_stealth_enabled.E7 = stepperE7.get_stealthChop_status();
#endif
#endif // MAX_EXTRUDERS > 7
#endif // MAX_EXTRUDERS > 6
#endif // MAX_EXTRUDERS > 5 #endif // MAX_EXTRUDERS > 5
#endif // MAX_EXTRUDERS > 4 #endif // MAX_EXTRUDERS > 4
#endif // MAX_EXTRUDERS > 3 #endif // MAX_EXTRUDERS > 3
@ -2788,6 +2818,14 @@ void MarlinSettings::reset() {
#if EXTRUDERS > 5 #if EXTRUDERS > 5
CONFIG_ECHO_START(); CONFIG_ECHO_START();
SERIAL_ECHOLNPAIR(" M200 T5 D", LINEAR_UNIT(planner.filament_size[5])); SERIAL_ECHOLNPAIR(" M200 T5 D", LINEAR_UNIT(planner.filament_size[5]));
#if EXTRUDERS > 6
CONFIG_ECHO_START();
SERIAL_ECHOLNPAIR(" M200 T6 D", LINEAR_UNIT(planner.filament_size[6]));
#if EXTRUDERS > 7
CONFIG_ECHO_START();
SERIAL_ECHOLNPAIR(" M200 T7 D", LINEAR_UNIT(planner.filament_size[7]));
#endif // EXTRUDERS > 7
#endif // EXTRUDERS > 6
#endif // EXTRUDERS > 5 #endif // EXTRUDERS > 5
#endif // EXTRUDERS > 4 #endif // EXTRUDERS > 4
#endif // EXTRUDERS > 3 #endif // EXTRUDERS > 3
@ -3528,6 +3566,12 @@ void MarlinSettings::reset() {
_ECHO_603(4); _ECHO_603(4);
#if EXTRUDERS > 5 #if EXTRUDERS > 5
_ECHO_603(5); _ECHO_603(5);
#if EXTRUDERS > 6
_ECHO_603(6);
#if EXTRUDERS > 7
_ECHO_603(7);
#endif // EXTRUDERS > 7
#endif // EXTRUDERS > 6
#endif // EXTRUDERS > 5 #endif // EXTRUDERS > 5
#endif // EXTRUDERS > 4 #endif // EXTRUDERS > 4
#endif // EXTRUDERS > 3 #endif // EXTRUDERS > 3

View File

@ -486,14 +486,20 @@ void _O2 Endstops::report_states() {
default: continue; default: continue;
case 1: pin = FIL_RUNOUT_PIN; break; case 1: pin = FIL_RUNOUT_PIN; break;
case 2: pin = FIL_RUNOUT2_PIN; break; case 2: pin = FIL_RUNOUT2_PIN; break;
#if NUM_RUNOUT_SENSORS > 2 #if NUM_RUNOUT_SENSORS >= 3
case 3: pin = FIL_RUNOUT3_PIN; break; case 3: pin = FIL_RUNOUT3_PIN; break;
#if NUM_RUNOUT_SENSORS > 3 #if NUM_RUNOUT_SENSORS >= 4
case 4: pin = FIL_RUNOUT4_PIN; break; case 4: pin = FIL_RUNOUT4_PIN; break;
#if NUM_RUNOUT_SENSORS > 4 #if NUM_RUNOUT_SENSORS >= 5
case 5: pin = FIL_RUNOUT5_PIN; break; case 5: pin = FIL_RUNOUT5_PIN; break;
#if NUM_RUNOUT_SENSORS > 5 #if NUM_RUNOUT_SENSORS >= 6
case 6: pin = FIL_RUNOUT6_PIN; break; case 6: pin = FIL_RUNOUT6_PIN; break;
#if NUM_RUNOUT_SENSORS >= 7
case 7: pin = FIL_RUNOUT7_PIN; break;
#if NUM_RUNOUT_SENSORS >= 8
case 8: pin = FIL_RUNOUT8_PIN; break;
#endif
#endif
#endif #endif
#endif #endif
#endif #endif

View File

@ -1308,7 +1308,21 @@ void Planner::check_axes_activity() {
#if HAS_FAN2 #if HAS_FAN2
FAN_SET(2); FAN_SET(2);
#endif #endif
#if HAS_FAN3
FAN_SET(3);
#endif
#if HAS_FAN4
FAN_SET(4);
#endif
#if HAS_FAN5
FAN_SET(5);
#endif
#if HAS_FAN6
FAN_SET(6);
#endif
#if HAS_FAN7
FAN_SET(7);
#endif
#endif // FAN_COUNT > 0 #endif // FAN_COUNT > 0
#if ENABLED(AUTOTEMP) #if ENABLED(AUTOTEMP)

View File

@ -2140,6 +2140,12 @@ void Stepper::init() {
#if HAS_E5_DIR #if HAS_E5_DIR
E5_DIR_INIT(); E5_DIR_INIT();
#endif #endif
#if HAS_E6_DIR
E6_DIR_INIT();
#endif
#if HAS_E7_DIR
E7_DIR_INIT();
#endif
// Init Enable Pins - steppers default to disabled. // Init Enable Pins - steppers default to disabled.
#if HAS_X_ENABLE #if HAS_X_ENABLE
@ -2198,6 +2204,14 @@ void Stepper::init() {
E5_ENABLE_INIT(); E5_ENABLE_INIT();
if (!E_ENABLE_ON) E5_ENABLE_WRITE(HIGH); if (!E_ENABLE_ON) E5_ENABLE_WRITE(HIGH);
#endif #endif
#if HAS_E6_ENABLE
E6_ENABLE_INIT();
if (!E_ENABLE_ON) E6_ENABLE_WRITE(HIGH);
#endif
#if HAS_E7_ENABLE
E7_ENABLE_INIT();
if (!E_ENABLE_ON) E7_ENABLE_WRITE(HIGH);
#endif
#define _STEP_INIT(AXIS) AXIS ##_STEP_INIT() #define _STEP_INIT(AXIS) AXIS ##_STEP_INIT()
#define _WRITE_STEP(AXIS, HIGHLOW) AXIS ##_STEP_WRITE(HIGHLOW) #define _WRITE_STEP(AXIS, HIGHLOW) AXIS ##_STEP_WRITE(HIGHLOW)
@ -2261,6 +2275,12 @@ void Stepper::init() {
#if E_STEPPERS > 5 && HAS_E5_STEP #if E_STEPPERS > 5 && HAS_E5_STEP
E_AXIS_INIT(5); E_AXIS_INIT(5);
#endif #endif
#if E_STEPPERS > 6 && HAS_E6_STEP
E_AXIS_INIT(6);
#endif
#if E_STEPPERS > 7 && HAS_E7_STEP
E_AXIS_INIT(7);
#endif
#if DISABLED(I2S_STEPPER_STREAM) #if DISABLED(I2S_STEPPER_STREAM)
HAL_timer_start(STEP_TIMER_NUM, 122); // Init Stepper ISR to 122 Hz for quick starting HAL_timer_start(STEP_TIMER_NUM, 122); // Init Stepper ISR to 122 Hz for quick starting
@ -2802,6 +2822,20 @@ void Stepper::report_positions() {
SET_OUTPUT(E5_MS3_PIN); SET_OUTPUT(E5_MS3_PIN);
#endif #endif
#endif #endif
#if HAS_E6_MICROSTEPS
SET_OUTPUT(E6_MS1_PIN);
SET_OUTPUT(E6_MS2_PIN);
#if PIN_EXISTS(E6_MS3)
SET_OUTPUT(E6_MS3_PIN);
#endif
#endif
#if HAS_E7_MICROSTEPS
SET_OUTPUT(E7_MS1_PIN);
SET_OUTPUT(E7_MS2_PIN);
#if PIN_EXISTS(E7_MS3)
SET_OUTPUT(E7_MS3_PIN);
#endif
#endif
static const uint8_t microstep_modes[] = MICROSTEP_MODES; static const uint8_t microstep_modes[] = MICROSTEP_MODES;
for (uint16_t i = 0; i < COUNT(microstep_modes); i++) for (uint16_t i = 0; i < COUNT(microstep_modes); i++)
@ -2864,6 +2898,12 @@ void Stepper::report_positions() {
#if HAS_E5_MICROSTEPS #if HAS_E5_MICROSTEPS
case 8: WRITE(E5_MS1_PIN, ms1); break; case 8: WRITE(E5_MS1_PIN, ms1); break;
#endif #endif
#if HAS_E6_MICROSTEPS
case 9: WRITE(E6_MS1_PIN, ms1); break;
#endif
#if HAS_E7_MICROSTEPS
case 10: WRITE(E7_MS1_PIN, ms1); break;
#endif
} }
if (ms2 >= 0) switch (driver) { if (ms2 >= 0) switch (driver) {
#if HAS_X_MICROSTEPS || HAS_X2_MICROSTEPS #if HAS_X_MICROSTEPS || HAS_X2_MICROSTEPS
@ -2920,6 +2960,12 @@ void Stepper::report_positions() {
#if HAS_E5_MICROSTEPS #if HAS_E5_MICROSTEPS
case 8: WRITE(E5_MS2_PIN, ms2); break; case 8: WRITE(E5_MS2_PIN, ms2); break;
#endif #endif
#if HAS_E6_MICROSTEPS
case 9: WRITE(E6_MS2_PIN, ms2); break;
#endif
#if HAS_E7_MICROSTEPS
case 10: WRITE(E7_MS2_PIN, ms2); break;
#endif
} }
if (ms3 >= 0) switch (driver) { if (ms3 >= 0) switch (driver) {
#if HAS_X_MICROSTEPS || HAS_X2_MICROSTEPS #if HAS_X_MICROSTEPS || HAS_X2_MICROSTEPS
@ -2976,6 +3022,12 @@ void Stepper::report_positions() {
#if HAS_E5_MICROSTEPS && PIN_EXISTS(E5_MS3) #if HAS_E5_MICROSTEPS && PIN_EXISTS(E5_MS3)
case 8: WRITE(E5_MS3_PIN, ms3); break; case 8: WRITE(E5_MS3_PIN, ms3); break;
#endif #endif
#if HAS_E6_MICROSTEPS && PIN_EXISTS(E6_MS3)
case 9: WRITE(E6_MS3_PIN, ms3); break;
#endif
#if HAS_E7_MICROSTEPS && PIN_EXISTS(E7_MS3)
case 10: WRITE(E7_MS3_PIN, ms3); break;
#endif
} }
} }
@ -3084,6 +3136,22 @@ void Stepper::report_positions() {
#endif #endif
); );
#endif #endif
#if HAS_E6_MICROSTEPS
SERIAL_ECHOPGM("E6: ");
SERIAL_CHAR('0' + READ(E6_MS1_PIN), '0' + READ(E6_MS2_PIN)
#if PIN_EXISTS(E6_MS3)
, '0' + READ(E6_MS3_PIN)
#endif
);
#endif
#if HAS_E7_MICROSTEPS
SERIAL_ECHOPGM("E7: ");
SERIAL_CHAR('0' + READ(E7_MS1_PIN), '0' + READ(E7_MS2_PIN)
#if PIN_EXISTS(E7_MS3)
, '0' + READ(E7_MS3_PIN)
#endif
);
#endif
} }
#endif // HAS_MICROSTEPS #endif // HAS_MICROSTEPS

View File

@ -278,3 +278,37 @@
#define E5_DIR_READ() (stepper##E5.getStatus() & STATUS_DIR); #define E5_DIR_READ() (stepper##E5.getStatus() & STATUS_DIR);
#endif #endif
#endif #endif
// E6 Stepper
#if AXIS_IS_L64XX(E6)
extern L64XX_CLASS(E6) stepperE6;
#define E6_ENABLE_INIT() NOOP
#define E6_ENABLE_WRITE(STATE) (STATE ? NOOP : stepperE6.free())
#define E6_ENABLE_READ() (stepperE6.getStatus() & STATUS_HIZ)
#if AXIS_DRIVER_TYPE_E6(L6474)
#define E6_DIR_INIT() SET_OUTPUT(E6_DIR_PIN)
#define E6_DIR_WRITE(STATE) L6474_DIR_WRITE(E6, STATE)
#define E6_DIR_READ() READ(E6_DIR_PIN)
#else
#define E6_DIR_INIT() NOOP
#define E6_DIR_WRITE(STATE) L64XX_DIR_WRITE(E6, STATE)
#define E6_DIR_READ() (stepper##E6.getStatus() & STATUS_DIR);
#endif
#endif
// E7 Stepper
#if AXIS_IS_L64XX(E7)
extern L64XX_CLASS(E7) stepperE7;
#define E7_ENABLE_INIT() NOOP
#define E7_ENABLE_WRITE(STATE) (STATE ? NOOP : stepperE7.free())
#define E7_ENABLE_READ() (stepperE7.getStatus() & STATUS_HIZ)
#if AXIS_DRIVER_TYPE_E7(L6474)
#define E7_DIR_INIT() SET_OUTPUT(E7_DIR_PIN)
#define E7_DIR_WRITE(STATE) L6474_DIR_WRITE(E7, STATE)
#define E7_DIR_READ() READ(E7_DIR_PIN)
#else
#define E7_DIR_INIT() NOOP
#define E7_DIR_WRITE(STATE) L64XX_DIR_WRITE(E7, STATE)
#define E7_DIR_READ() (stepper##E7.getStatus() & STATUS_DIR);
#endif
#endif

View File

@ -150,3 +150,19 @@ void tmc26x_init_to_defaults();
#define E5_ENABLE_WRITE(STATE) stepperE5.setEnabled(STATE) #define E5_ENABLE_WRITE(STATE) stepperE5.setEnabled(STATE)
#define E5_ENABLE_READ() stepperE5.isEnabled() #define E5_ENABLE_READ() stepperE5.isEnabled()
#endif #endif
// E6 Stepper
#if AXIS_DRIVER_TYPE_E6(TMC26X)
extern TMC26XStepper stepperE6;
#define E6_ENABLE_INIT() NOOP
#define E6_ENABLE_WRITE(STATE) stepperE6.setEnabled(STATE)
#define E6_ENABLE_READ() stepperE6.isEnabled()
#endif
// E7 Stepper
#if AXIS_DRIVER_TYPE_E7(TMC26X)
extern TMC26XStepper stepperE7;
#define E7_ENABLE_INIT() NOOP
#define E7_ENABLE_WRITE(STATE) stepperE7.setEnabled(STATE)
#define E7_ENABLE_READ() stepperE7.isEnabled()
#endif

View File

@ -303,26 +303,115 @@ void reset_stepper_drivers(); // Called by settings.load / settings.reset
#endif #endif
#define E5_STEP_READ() bool(READ(E5_STEP_PIN)) #define E5_STEP_READ() bool(READ(E5_STEP_PIN))
// E6 Stepper
#ifndef E6_ENABLE_INIT
#define E6_ENABLE_INIT() SET_OUTPUT(E6_ENABLE_PIN)
#define E6_ENABLE_WRITE(STATE) WRITE(E6_ENABLE_PIN,STATE)
#define E6_ENABLE_READ() bool(READ(E6_ENABLE_PIN))
#endif
#ifndef E6_DIR_INIT
#define E6_DIR_INIT() SET_OUTPUT(E6_DIR_PIN)
#define E6_DIR_WRITE(STATE) WRITE(E6_DIR_PIN,STATE)
#define E6_DIR_READ() bool(READ(E6_DIR_PIN))
#endif
#define E6_STEP_INIT() SET_OUTPUT(E6_STEP_PIN)
#ifndef E6_STEP_WRITE
#define E6_STEP_WRITE(STATE) WRITE(E6_STEP_PIN,STATE)
#endif
#define E6_STEP_READ() bool(READ(E6_STEP_PIN))
// E7 Stepper
#ifndef E7_ENABLE_INIT
#define E7_ENABLE_INIT() SET_OUTPUT(E7_ENABLE_PIN)
#define E7_ENABLE_WRITE(STATE) WRITE(E7_ENABLE_PIN,STATE)
#define E7_ENABLE_READ() bool(READ(E7_ENABLE_PIN))
#endif
#ifndef E7_DIR_INIT
#define E7_DIR_INIT() SET_OUTPUT(E7_DIR_PIN)
#define E7_DIR_WRITE(STATE) WRITE(E7_DIR_PIN,STATE)
#define E7_DIR_READ() bool(READ(E7_DIR_PIN))
#endif
#define E7_STEP_INIT() SET_OUTPUT(E7_STEP_PIN)
#ifndef E7_STEP_WRITE
#define E7_STEP_WRITE(STATE) WRITE(E7_STEP_PIN,STATE)
#endif
#define E7_STEP_READ() bool(READ(E7_STEP_PIN))
/** /**
* Extruder indirection for the single E axis * Extruder indirection for the single E axis
*/ */
#if ENABLED(SWITCHING_EXTRUDER) // One stepper driver per two extruders, reversed on odd index #if ENABLED(SWITCHING_EXTRUDER) // One stepper driver per two extruders, reversed on odd index
#if EXTRUDERS > 5 #if EXTRUDERS > 7
#define E_STEP_WRITE(E,V) do{ if (E < 2) { E0_STEP_WRITE(V); } else if (E < 4) { E1_STEP_WRITE(V); } else if (E < 6) { E2_STEP_WRITE(V); } else { E3_STEP_WRITE(V); } }while(0)
#define NORM_E_DIR(E) do{ switch (E) { \
case 0: E0_DIR_WRITE(!INVERT_E0_DIR); break; case 1: E0_DIR_WRITE( INVERT_E0_DIR); break; \
case 2: E1_DIR_WRITE(!INVERT_E1_DIR); break; case 3: E1_DIR_WRITE( INVERT_E1_DIR); break; \
case 4: E2_DIR_WRITE(!INVERT_E2_DIR); break; case 5: E2_DIR_WRITE( INVERT_E2_DIR); break; \
case 6: E3_DIR_WRITE( INVERT_E3_DIR); break; case 7: E3_DIR_WRITE( INVERT_E3_DIR); break; \
} }while(0)
#define REV_E_DIR(E) do{ switch (E) { \
case 0: E0_DIR_WRITE( INVERT_E0_DIR); break; case 1: E0_DIR_WRITE(!INVERT_E0_DIR); break; \
case 2: E1_DIR_WRITE( INVERT_E1_DIR); break; case 3: E1_DIR_WRITE(!INVERT_E1_DIR); break; \
case 4: E2_DIR_WRITE( INVERT_E2_DIR); break; case 5: E2_DIR_WRITE(!INVERT_E2_DIR); break; \
case 6: E3_DIR_WRITE(!INVERT_E3_DIR); break; case 7: E3_DIR_WRITE(!INVERT_E3_DIR); break; \
} }while(0)
#elif EXTRUDERS > 6
#define E_STEP_WRITE(E,V) do{ if (E < 2) { E0_STEP_WRITE(V); } else if (E < 4) { E1_STEP_WRITE(V); } else if (E < 6) { E2_STEP_WRITE(V); } else { E3_STEP_WRITE(V); } }while(0)
#define NORM_E_DIR(E) do{ switch (E) { \
case 0: E0_DIR_WRITE(!INVERT_E0_DIR); break; case 1: E0_DIR_WRITE( INVERT_E0_DIR); break; \
case 2: E1_DIR_WRITE(!INVERT_E1_DIR); break; case 3: E1_DIR_WRITE( INVERT_E1_DIR); break; \
case 4: E2_DIR_WRITE(!INVERT_E2_DIR); break; case 5: E2_DIR_WRITE( INVERT_E2_DIR); break; \
case 6: E3_DIR_WRITE( INVERT_E3_DIR); break; \
} }while(0)
#define REV_E_DIR(E) do{ switch (E) { \
case 0: E0_DIR_WRITE( INVERT_E0_DIR); break; case 1: E0_DIR_WRITE(!INVERT_E0_DIR); break; \
case 2: E1_DIR_WRITE( INVERT_E1_DIR); break; case 3: E1_DIR_WRITE(!INVERT_E1_DIR); break; \
case 4: E2_DIR_WRITE( INVERT_E2_DIR); break; case 5: E2_DIR_WRITE(!INVERT_E2_DIR); break; \
case 6: E3_DIR_WRITE(!INVERT_E3_DIR); } }while(0)
#elif EXTRUDERS > 5
#define E_STEP_WRITE(E,V) do{ if (E < 2) { E0_STEP_WRITE(V); } else if (E < 4) { E1_STEP_WRITE(V); } else { E2_STEP_WRITE(V); } }while(0) #define E_STEP_WRITE(E,V) do{ if (E < 2) { E0_STEP_WRITE(V); } else if (E < 4) { E1_STEP_WRITE(V); } else { E2_STEP_WRITE(V); } }while(0)
#define NORM_E_DIR(E) do{ switch (E) { case 0: E0_DIR_WRITE(!INVERT_E0_DIR); break; case 1: E0_DIR_WRITE( INVERT_E0_DIR); break; case 2: E1_DIR_WRITE(!INVERT_E1_DIR); break; case 3: E1_DIR_WRITE( INVERT_E1_DIR); break; case 4: E2_DIR_WRITE(!INVERT_E2_DIR); case 5: E2_DIR_WRITE( INVERT_E2_DIR); } }while(0) #define NORM_E_DIR(E) do{ switch (E) { \
#define REV_E_DIR(E) do{ switch (E) { case 0: E0_DIR_WRITE( INVERT_E0_DIR); break; case 1: E0_DIR_WRITE(!INVERT_E0_DIR); break; case 2: E1_DIR_WRITE( INVERT_E1_DIR); break; case 3: E1_DIR_WRITE(!INVERT_E1_DIR); break; case 4: E2_DIR_WRITE( INVERT_E2_DIR); case 5: E2_DIR_WRITE(!INVERT_E2_DIR); } }while(0) case 0: E0_DIR_WRITE(!INVERT_E0_DIR); break; case 1: E0_DIR_WRITE( INVERT_E0_DIR); break; \
case 2: E1_DIR_WRITE(!INVERT_E1_DIR); break; case 3: E1_DIR_WRITE( INVERT_E1_DIR); break; \
case 4: E2_DIR_WRITE(!INVERT_E2_DIR); break; case 5: E2_DIR_WRITE( INVERT_E2_DIR); break; \
} }while(0)
#define REV_E_DIR(E) do{ switch (E) { \
case 0: E0_DIR_WRITE( INVERT_E0_DIR); break; case 1: E0_DIR_WRITE(!INVERT_E0_DIR); break; \
case 2: E1_DIR_WRITE( INVERT_E1_DIR); break; case 3: E1_DIR_WRITE(!INVERT_E1_DIR); break; \
case 4: E2_DIR_WRITE( INVERT_E2_DIR); break; case 5: E2_DIR_WRITE(!INVERT_E2_DIR); break; \
} }while(0)
#elif EXTRUDERS > 4 #elif EXTRUDERS > 4
#define E_STEP_WRITE(E,V) do{ if (E < 2) { E0_STEP_WRITE(V); } else if (E < 4) { E1_STEP_WRITE(V); } else { E2_STEP_WRITE(V); } }while(0) #define E_STEP_WRITE(E,V) do{ if (E < 2) { E0_STEP_WRITE(V); } else if (E < 4) { E1_STEP_WRITE(V); } else { E2_STEP_WRITE(V); } }while(0)
#define NORM_E_DIR(E) do{ switch (E) { case 0: E0_DIR_WRITE(!INVERT_E0_DIR); break; case 1: E0_DIR_WRITE( INVERT_E0_DIR); break; case 2: E1_DIR_WRITE(!INVERT_E1_DIR); break; case 3: E1_DIR_WRITE( INVERT_E1_DIR); break; case 4: E2_DIR_WRITE(!INVERT_E2_DIR); } }while(0) #define NORM_E_DIR(E) do{ switch (E) { \
#define REV_E_DIR(E) do{ switch (E) { case 0: E0_DIR_WRITE( INVERT_E0_DIR); break; case 1: E0_DIR_WRITE(!INVERT_E0_DIR); break; case 2: E1_DIR_WRITE( INVERT_E1_DIR); break; case 3: E1_DIR_WRITE(!INVERT_E1_DIR); break; case 4: E2_DIR_WRITE( INVERT_E2_DIR); } }while(0) case 0: E0_DIR_WRITE(!INVERT_E0_DIR); break; case 1: E0_DIR_WRITE( INVERT_E0_DIR); break; \
case 2: E1_DIR_WRITE(!INVERT_E1_DIR); break; case 3: E1_DIR_WRITE( INVERT_E1_DIR); break; \
case 4: E2_DIR_WRITE(!INVERT_E2_DIR); break; \
} }while(0)
#define REV_E_DIR(E) do{ switch (E) { \
case 0: E0_DIR_WRITE( INVERT_E0_DIR); break; case 1: E0_DIR_WRITE(!INVERT_E0_DIR); break; \
case 2: E1_DIR_WRITE( INVERT_E1_DIR); break; case 3: E1_DIR_WRITE(!INVERT_E1_DIR); break; \
case 4: E2_DIR_WRITE( INVERT_E2_DIR); break; \
} }while(0)
#elif EXTRUDERS > 3 #elif EXTRUDERS > 3
#define E_STEP_WRITE(E,V) do{ if (E < 2) { E0_STEP_WRITE(V); } else { E1_STEP_WRITE(V); } }while(0) #define E_STEP_WRITE(E,V) do{ if (E < 2) { E0_STEP_WRITE(V); } else { E1_STEP_WRITE(V); } }while(0)
#define NORM_E_DIR(E) do{ switch (E) { case 0: E0_DIR_WRITE(!INVERT_E0_DIR); break; case 1: E0_DIR_WRITE( INVERT_E0_DIR); break; case 2: E1_DIR_WRITE(!INVERT_E1_DIR); break; case 3: E1_DIR_WRITE( INVERT_E1_DIR); } }while(0) #define NORM_E_DIR(E) do{ switch (E) { \
#define REV_E_DIR(E) do{ switch (E) { case 0: E0_DIR_WRITE( INVERT_E0_DIR); break; case 1: E0_DIR_WRITE(!INVERT_E0_DIR); break; case 2: E1_DIR_WRITE( INVERT_E1_DIR); break; case 3: E1_DIR_WRITE(!INVERT_E1_DIR); } }while(0) case 0: E0_DIR_WRITE(!INVERT_E0_DIR); break; case 1: E0_DIR_WRITE( INVERT_E0_DIR); break; \
case 2: E1_DIR_WRITE(!INVERT_E1_DIR); break; case 3: E1_DIR_WRITE( INVERT_E1_DIR); break; \
} }while(0)
#define REV_E_DIR(E) do{ switch (E) { \
case 0: E0_DIR_WRITE( INVERT_E0_DIR); break; case 1: E0_DIR_WRITE(!INVERT_E0_DIR); break; \
case 2: E1_DIR_WRITE( INVERT_E1_DIR); break; case 3: E1_DIR_WRITE(!INVERT_E1_DIR); break; \
} }while(0)
#elif EXTRUDERS > 2 #elif EXTRUDERS > 2
#define E_STEP_WRITE(E,V) do{ if (E < 2) { E0_STEP_WRITE(V); } else { E1_STEP_WRITE(V); } }while(0) #define E_STEP_WRITE(E,V) do{ if (E < 2) { E0_STEP_WRITE(V); } else { E1_STEP_WRITE(V); } }while(0)
#define NORM_E_DIR(E) do{ switch (E) { case 0: E0_DIR_WRITE(!INVERT_E0_DIR); break; case 1: E0_DIR_WRITE( INVERT_E0_DIR); break; case 2: E1_DIR_WRITE(!INVERT_E1_DIR); } }while(0) #define NORM_E_DIR(E) do{ switch (E) { \
#define REV_E_DIR(E) do{ switch (E) { case 0: E0_DIR_WRITE( INVERT_E0_DIR); break; case 1: E0_DIR_WRITE(!INVERT_E0_DIR); break; case 2: E1_DIR_WRITE( INVERT_E1_DIR); } }while(0) case 0: E0_DIR_WRITE(!INVERT_E0_DIR); break; case 1: E0_DIR_WRITE( INVERT_E0_DIR); break; \
case 2: E1_DIR_WRITE(!INVERT_E1_DIR); break; \
} }while(0)
#define REV_E_DIR(E) do{ switch (E) { \
case 0: E0_DIR_WRITE( INVERT_E0_DIR); break; case 1: E0_DIR_WRITE(!INVERT_E0_DIR); break; \
case 2: E1_DIR_WRITE( INVERT_E1_DIR); break; \
} }while(0)
#else #else
#define E_STEP_WRITE(E,V) E0_STEP_WRITE(V) #define E_STEP_WRITE(E,V) E0_STEP_WRITE(V)
#define NORM_E_DIR(E) do{ E0_DIR_WRITE(E ? INVERT_E0_DIR : !INVERT_E0_DIR); }while(0) #define NORM_E_DIR(E) do{ E0_DIR_WRITE(E ? INVERT_E0_DIR : !INVERT_E0_DIR); }while(0)
@ -340,23 +429,100 @@ void reset_stepper_drivers(); // Called by settings.load / settings.reset
#elif E_STEPPERS > 1 #elif E_STEPPERS > 1
#if E_STEPPERS > 5 #if E_STEPPERS > 7
#define _E_STEP_WRITE(E,V) do{ switch (E) { case 0: E0_STEP_WRITE(V); break; case 1: E1_STEP_WRITE(V); break; case 2: E2_STEP_WRITE(V); break; case 3: E3_STEP_WRITE(V); break; case 4: E4_STEP_WRITE(V); case 5: E5_STEP_WRITE(V); } }while(0)
#define _NORM_E_DIR(E) do{ switch (E) { case 0: E0_DIR_WRITE(!INVERT_E0_DIR); break; case 1: E1_DIR_WRITE(!INVERT_E1_DIR); break; case 2: E2_DIR_WRITE(!INVERT_E2_DIR); break; case 3: E3_DIR_WRITE(!INVERT_E3_DIR); break; case 4: E4_DIR_WRITE(!INVERT_E4_DIR); case 5: E5_DIR_WRITE(!INVERT_E5_DIR); } }while(0) #define _E_STEP_WRITE(E,V) do{ switch (E) { \
#define _REV_E_DIR(E) do{ switch (E) { case 0: E0_DIR_WRITE( INVERT_E0_DIR); break; case 1: E1_DIR_WRITE( INVERT_E1_DIR); break; case 2: E2_DIR_WRITE( INVERT_E2_DIR); break; case 3: E3_DIR_WRITE( INVERT_E3_DIR); break; case 4: E4_DIR_WRITE( INVERT_E4_DIR); case 5: E5_DIR_WRITE( INVERT_E5_DIR); } }while(0) case 0: E0_STEP_WRITE(V); break; case 1: E1_STEP_WRITE(V); break; case 2: E2_STEP_WRITE(V); break; case 3: E3_STEP_WRITE(V); break; \
case 4: E4_STEP_WRITE(V); break; case 5: E5_STEP_WRITE(V); break; case 6: E6_STEP_WRITE(V); break; case 7: E7_STEP_WRITE(V); break; \
} }while(0)
#define _NORM_E_DIR(E) do{ switch (E) { \
case 0: E0_DIR_WRITE(!INVERT_E0_DIR); break; case 1: E1_DIR_WRITE(!INVERT_E1_DIR); break; \
case 2: E2_DIR_WRITE(!INVERT_E2_DIR); break; case 3: E3_DIR_WRITE(!INVERT_E3_DIR); break; \
case 4: E4_DIR_WRITE(!INVERT_E4_DIR); break; case 5: E5_DIR_WRITE(!INVERT_E5_DIR); break; \
case 6: E6_DIR_WRITE(!INVERT_E6_DIR); break; case 7: E7_DIR_WRITE(!INVERT_E7_DIR); break; \
} }while(0)
#define _REV_E_DIR(E) do{ switch (E) { \
case 0: E0_DIR_WRITE( INVERT_E0_DIR); break; case 1: E1_DIR_WRITE( INVERT_E1_DIR); break; \
case 2: E2_DIR_WRITE( INVERT_E2_DIR); break; case 3: E3_DIR_WRITE( INVERT_E3_DIR); break; \
case 4: E4_DIR_WRITE( INVERT_E4_DIR); break; case 5: E5_DIR_WRITE( INVERT_E5_DIR); break; \
case 6: E6_DIR_WRITE( INVERT_E6_DIR); break; case 7: E7_DIR_WRITE( INVERT_E7_DIR); break; \
} }while(0)
#elif E_STEPPERS > 6
#define _E_STEP_WRITE(E,V) do{ switch (E) { \
case 0: E0_STEP_WRITE(V); break; case 1: E1_STEP_WRITE(V); break; case 2: E2_STEP_WRITE(V); break; case 3: E3_STEP_WRITE(V); break; \
case 4: E4_STEP_WRITE(V); break; case 5: E5_STEP_WRITE(V); break; case 6: E6_STEP_WRITE(V); break; \
} }while(0)
#define _NORM_E_DIR(E) do{ switch (E) { \
case 0: E0_DIR_WRITE(!INVERT_E0_DIR); break; case 1: E1_DIR_WRITE(!INVERT_E1_DIR); break; \
case 2: E2_DIR_WRITE(!INVERT_E2_DIR); break; case 3: E3_DIR_WRITE(!INVERT_E3_DIR); break; \
case 4: E4_DIR_WRITE(!INVERT_E4_DIR); break; case 5: E5_DIR_WRITE(!INVERT_E5_DIR); break; \
case 6: E6_DIR_WRITE(!INVERT_E6_DIR); break; \
} }while(0)
#define _REV_E_DIR(E) do{ switch (E) { \
case 0: E0_DIR_WRITE( INVERT_E0_DIR); break; case 1: E1_DIR_WRITE( INVERT_E1_DIR); break; \
case 2: E2_DIR_WRITE( INVERT_E2_DIR); break; case 3: E3_DIR_WRITE( INVERT_E3_DIR); break; \
case 4: E4_DIR_WRITE( INVERT_E4_DIR); break; case 5: E5_DIR_WRITE( INVERT_E5_DIR); break; \
case 6: E6_DIR_WRITE( INVERT_E6_DIR); break; \
} }while(0)
#elif E_STEPPERS > 5
#define _E_STEP_WRITE(E,V) do{ switch (E) { \
case 0: E0_STEP_WRITE(V); break; case 1: E1_STEP_WRITE(V); break; case 2: E2_STEP_WRITE(V); break; case 3: E3_STEP_WRITE(V); break; \
case 4: E4_STEP_WRITE(V); break; case 5: E5_STEP_WRITE(V); break; \
} }while(0)
#define _NORM_E_DIR(E) do{ switch (E) { \
case 0: E0_DIR_WRITE(!INVERT_E0_DIR); break; case 1: E1_DIR_WRITE(!INVERT_E1_DIR); break; \
case 2: E2_DIR_WRITE(!INVERT_E2_DIR); break; case 3: E3_DIR_WRITE(!INVERT_E3_DIR); break; \
case 4: E4_DIR_WRITE(!INVERT_E4_DIR); break; case 5: E5_DIR_WRITE(!INVERT_E5_DIR); break; \
} }while(0)
#define _REV_E_DIR(E) do{ switch (E) { \
case 0: E0_DIR_WRITE( INVERT_E0_DIR); break; case 1: E1_DIR_WRITE( INVERT_E1_DIR); break; \
case 2: E2_DIR_WRITE( INVERT_E2_DIR); break; case 3: E3_DIR_WRITE( INVERT_E3_DIR); break; \
case 4: E4_DIR_WRITE( INVERT_E4_DIR); break; case 5: E5_DIR_WRITE( INVERT_E5_DIR); break; \
} }while(0)
#elif E_STEPPERS > 4 #elif E_STEPPERS > 4
#define _E_STEP_WRITE(E,V) do{ switch (E) { case 0: E0_STEP_WRITE(V); break; case 1: E1_STEP_WRITE(V); break; case 2: E2_STEP_WRITE(V); break; case 3: E3_STEP_WRITE(V); break; case 4: E4_STEP_WRITE(V); } }while(0)
#define _NORM_E_DIR(E) do{ switch (E) { case 0: E0_DIR_WRITE(!INVERT_E0_DIR); break; case 1: E1_DIR_WRITE(!INVERT_E1_DIR); break; case 2: E2_DIR_WRITE(!INVERT_E2_DIR); break; case 3: E3_DIR_WRITE(!INVERT_E3_DIR); break; case 4: E4_DIR_WRITE(!INVERT_E4_DIR); } }while(0) #define _E_STEP_WRITE(E,V) do{ switch (E) { \
#define _REV_E_DIR(E) do{ switch (E) { case 0: E0_DIR_WRITE( INVERT_E0_DIR); break; case 1: E1_DIR_WRITE( INVERT_E1_DIR); break; case 2: E2_DIR_WRITE( INVERT_E2_DIR); break; case 3: E3_DIR_WRITE( INVERT_E3_DIR); break; case 4: E4_DIR_WRITE( INVERT_E4_DIR); } }while(0) case 0: E0_STEP_WRITE(V); break; case 1: E1_STEP_WRITE(V); break; case 2: E2_STEP_WRITE(V); break; case 3: E3_STEP_WRITE(V); break; \
case 4: E4_STEP_WRITE(V); break; \
} }while(0)
#define _NORM_E_DIR(E) do{ switch (E) { \
case 0: E0_DIR_WRITE(!INVERT_E0_DIR); break; case 1: E1_DIR_WRITE(!INVERT_E1_DIR); break; \
case 2: E2_DIR_WRITE(!INVERT_E2_DIR); break; case 3: E3_DIR_WRITE(!INVERT_E3_DIR); break; \
case 4: E4_DIR_WRITE(!INVERT_E4_DIR); break; \
} }while(0)
#define _REV_E_DIR(E) do{ switch (E) { \
case 0: E0_DIR_WRITE( INVERT_E0_DIR); break; case 1: E1_DIR_WRITE( INVERT_E1_DIR); break; \
case 2: E2_DIR_WRITE( INVERT_E2_DIR); break; case 3: E3_DIR_WRITE( INVERT_E3_DIR); break; \
case 4: E4_DIR_WRITE( INVERT_E4_DIR); break; \
} }while(0)
#elif E_STEPPERS > 3 #elif E_STEPPERS > 3
#define _E_STEP_WRITE(E,V) do{ switch (E) { case 0: E0_STEP_WRITE(V); break; case 1: E1_STEP_WRITE(V); break; case 2: E2_STEP_WRITE(V); break; case 3: E3_STEP_WRITE(V); } }while(0)
#define _NORM_E_DIR(E) do{ switch (E) { case 0: E0_DIR_WRITE(!INVERT_E0_DIR); break; case 1: E1_DIR_WRITE(!INVERT_E1_DIR); break; case 2: E2_DIR_WRITE(!INVERT_E2_DIR); break; case 3: E3_DIR_WRITE(!INVERT_E3_DIR); } }while(0) #define _E_STEP_WRITE(E,V) do{ switch (E) { \
#define _REV_E_DIR(E) do{ switch (E) { case 0: E0_DIR_WRITE( INVERT_E0_DIR); break; case 1: E1_DIR_WRITE( INVERT_E1_DIR); break; case 2: E2_DIR_WRITE( INVERT_E2_DIR); break; case 3: E3_DIR_WRITE( INVERT_E3_DIR); } }while(0) case 0: E0_STEP_WRITE(V); break; case 1: E1_STEP_WRITE(V); break; case 2: E2_STEP_WRITE(V); break; case 3: E3_STEP_WRITE(V); break; \
} }while(0)
#define _NORM_E_DIR(E) do{ switch (E) { \
case 0: E0_DIR_WRITE(!INVERT_E0_DIR); break; case 1: E1_DIR_WRITE(!INVERT_E1_DIR); break; \
case 2: E2_DIR_WRITE(!INVERT_E2_DIR); break; case 3: E3_DIR_WRITE(!INVERT_E3_DIR); break; \
} }while(0)
#define _REV_E_DIR(E) do{ switch (E) { \
case 0: E0_DIR_WRITE( INVERT_E0_DIR); break; case 1: E1_DIR_WRITE( INVERT_E1_DIR); break; \
case 2: E2_DIR_WRITE( INVERT_E2_DIR); break; case 3: E3_DIR_WRITE( INVERT_E3_DIR); break; \
} }while(0)
#elif E_STEPPERS > 2 #elif E_STEPPERS > 2
#define _E_STEP_WRITE(E,V) do{ switch (E) { case 0: E0_STEP_WRITE(V); break; case 1: E1_STEP_WRITE(V); break; case 2: E2_STEP_WRITE(V); } }while(0) #define _E_STEP_WRITE(E,V) do{ switch (E) { case 0: E0_STEP_WRITE(V); break; case 1: E1_STEP_WRITE(V); break; case 2: E2_STEP_WRITE(V); } }while(0)
#define _NORM_E_DIR(E) do{ switch (E) { case 0: E0_DIR_WRITE(!INVERT_E0_DIR); break; case 1: E1_DIR_WRITE(!INVERT_E1_DIR); break; case 2: E2_DIR_WRITE(!INVERT_E2_DIR); } }while(0) #define _NORM_E_DIR(E) do{ switch (E) { case 0: E0_DIR_WRITE(!INVERT_E0_DIR); break; case 1: E1_DIR_WRITE(!INVERT_E1_DIR); break; case 2: E2_DIR_WRITE(!INVERT_E2_DIR); } }while(0)
#define _REV_E_DIR(E) do{ switch (E) { case 0: E0_DIR_WRITE( INVERT_E0_DIR); break; case 1: E1_DIR_WRITE( INVERT_E1_DIR); break; case 2: E2_DIR_WRITE( INVERT_E2_DIR); } }while(0) #define _REV_E_DIR(E) do{ switch (E) { case 0: E0_DIR_WRITE( INVERT_E0_DIR); break; case 1: E1_DIR_WRITE( INVERT_E1_DIR); break; case 2: E2_DIR_WRITE( INVERT_E2_DIR); } }while(0)
#else #else
#define _E_STEP_WRITE(E,V) do{ if (E == 0) { E0_STEP_WRITE(V); } else { E1_STEP_WRITE(V); } }while(0) #define _E_STEP_WRITE(E,V) do{ if (E == 0) { E0_STEP_WRITE(V); } else { E1_STEP_WRITE(V); } }while(0)
#define _NORM_E_DIR(E) do{ if (E == 0) { E0_DIR_WRITE(!INVERT_E0_DIR); } else { E1_DIR_WRITE(!INVERT_E1_DIR); } }while(0) #define _NORM_E_DIR(E) do{ if (E == 0) { E0_DIR_WRITE(!INVERT_E0_DIR); } else { E1_DIR_WRITE(!INVERT_E1_DIR); } }while(0)
#define _REV_E_DIR(E) do{ if (E == 0) { E0_DIR_WRITE( INVERT_E0_DIR); } else { E1_DIR_WRITE( INVERT_E1_DIR); } }while(0) #define _REV_E_DIR(E) do{ if (E == 0) { E0_DIR_WRITE( INVERT_E0_DIR); } else { E1_DIR_WRITE( INVERT_E1_DIR); } }while(0)
@ -376,7 +542,15 @@ void reset_stepper_drivers(); // Called by settings.load / settings.reset
#define E_STEP_WRITE(E,V) do{ if (extruder_duplication_enabled) { DUPE(STEP,V); } else _E_STEP_WRITE(E,V); }while(0) #define E_STEP_WRITE(E,V) do{ if (extruder_duplication_enabled) { DUPE(STEP,V); } else _E_STEP_WRITE(E,V); }while(0)
#if E_STEPPERS > 2 #if E_STEPPERS > 2
#if E_STEPPERS > 5 #if E_STEPPERS > 7
#define DUPE(T,V) do{ _DUPE(0,T,V); _DUPE(1,T,V); _DUPE(2,T,V); _DUPE(3,T,V); _DUPE(4,T,V); _DUPE(5,T,V); _DUPE(6,T,V); _DUPE(7,T,V); }while(0)
#define NORM_E_DIR(E) do{ if (extruder_duplication_enabled) { NDIR(0); NDIR(1); NDIR(2); NDIR(3); NDIR(4); NDIR(5); NDIR(6); NDIR(7); } else _NORM_E_DIR(E); }while(0)
#define REV_E_DIR(E) do{ if (extruder_duplication_enabled) { RDIR(0); RDIR(1); RDIR(2); RDIR(3); RDIR(4); RDIR(5); RDIR(6); RDIR(7); } else _REV_E_DIR(E); }while(0)
#elif E_STEPPERS > 6
#define DUPE(T,V) do{ _DUPE(0,T,V); _DUPE(1,T,V); _DUPE(2,T,V); _DUPE(3,T,V); _DUPE(4,T,V); _DUPE(5,T,V); _DUPE(6,T,V); }while(0)
#define NORM_E_DIR(E) do{ if (extruder_duplication_enabled) { NDIR(0); NDIR(1); NDIR(2); NDIR(3); NDIR(4); NDIR(5); NDIR(6); } else _NORM_E_DIR(E); }while(0)
#define REV_E_DIR(E) do{ if (extruder_duplication_enabled) { RDIR(0); RDIR(1); RDIR(2); RDIR(3); RDIR(4); RDIR(5); RDIR(6); } else _REV_E_DIR(E); }while(0)
#elif E_STEPPERS > 5
#define DUPE(T,V) do{ _DUPE(0,T,V); _DUPE(1,T,V); _DUPE(2,T,V); _DUPE(3,T,V); _DUPE(4,T,V); _DUPE(5,T,V); }while(0) #define DUPE(T,V) do{ _DUPE(0,T,V); _DUPE(1,T,V); _DUPE(2,T,V); _DUPE(3,T,V); _DUPE(4,T,V); _DUPE(5,T,V); }while(0)
#define NORM_E_DIR(E) do{ if (extruder_duplication_enabled) { NDIR(0); NDIR(1); NDIR(2); NDIR(3); NDIR(4); NDIR(5); } else _NORM_E_DIR(E); }while(0) #define NORM_E_DIR(E) do{ if (extruder_duplication_enabled) { NDIR(0); NDIR(1); NDIR(2); NDIR(3); NDIR(4); NDIR(5); } else _NORM_E_DIR(E); }while(0)
#define REV_E_DIR(E) do{ if (extruder_duplication_enabled) { RDIR(0); RDIR(1); RDIR(2); RDIR(3); RDIR(4); RDIR(5); } else _REV_E_DIR(E); }while(0) #define REV_E_DIR(E) do{ if (extruder_duplication_enabled) { RDIR(0); RDIR(1); RDIR(2); RDIR(3); RDIR(4); RDIR(5); } else _REV_E_DIR(E); }while(0)
@ -604,12 +778,42 @@ void reset_stepper_drivers(); // Called by settings.load / settings.reset
#define E5_disable() NOOP #define E5_disable() NOOP
#endif #endif
#if AXIS_DRIVER_TYPE_E6(L6470)
extern L6470 stepperE6;
#define E6_enable() NOOP
#define E6_disable() do{ stepperE6.free(); CBI(axis_known_position, E_AXIS); }while(0)
#elif E_STEPPERS > 6 && HAS_E6_ENABLE
#define E6_enable() E6_ENABLE_WRITE( E_ENABLE_ON)
#define E6_disable() E6_ENABLE_WRITE(!E_ENABLE_ON)
#else
#define E6_enable() NOOP
#define E6_disable() NOOP
#endif
#if AXIS_DRIVER_TYPE_E7(L6470)
extern L6470 stepperE7;
#define E7_enable() NOOP
#define E7_disable() do{ stepperE7.free(); CBI(axis_known_position, E_AXIS); }while(0)
#elif E_STEPPERS > 7 && HAS_E7_ENABLE
#define E7_enable() E7_ENABLE_WRITE( E_ENABLE_ON)
#define E7_disable() E7_ENABLE_WRITE(!E_ENABLE_ON)
#else
#define E7_enable() NOOP
#define E7_disable() NOOP
#endif
#if ENABLED(MIXING_EXTRUDER) #if ENABLED(MIXING_EXTRUDER)
/** /**
* Mixing steppers synchronize their enable (and direction) together * Mixing steppers synchronize their enable (and direction) together
*/ */
#if MIXING_STEPPERS > 5 #if MIXING_STEPPERS > 7
#define enable_E0() { E0_enable(); E1_enable(); E2_enable(); E3_enable(); E4_enable(); E5_enable(); E6_enable(); E7_enable(); }
#define disable_E0() { E0_disable(); E1_disable(); E2_disable(); E3_disable(); E4_disable(); E5_disable(); E6_disable(); E7_disable(); }
#elif MIXING_STEPPERS > 6
#define enable_E0() { E0_enable(); E1_enable(); E2_enable(); E3_enable(); E4_enable(); E5_enable(); E6_enable(); }
#define disable_E0() { E0_disable(); E1_disable(); E2_disable(); E3_disable(); E4_disable(); E5_disable(); E6_disable(); }
#elif MIXING_STEPPERS > 5
#define enable_E0() { E0_enable(); E1_enable(); E2_enable(); E3_enable(); E4_enable(); E5_enable(); } #define enable_E0() { E0_enable(); E1_enable(); E2_enable(); E3_enable(); E4_enable(); E5_enable(); }
#define disable_E0() { E0_disable(); E1_disable(); E2_disable(); E3_disable(); E4_disable(); E5_disable(); } #define disable_E0() { E0_disable(); E1_disable(); E2_disable(); E3_disable(); E4_disable(); E5_disable(); }
#elif MIXING_STEPPERS > 4 #elif MIXING_STEPPERS > 4
@ -635,6 +839,10 @@ void reset_stepper_drivers(); // Called by settings.load / settings.reset
#define disable_E4() NOOP #define disable_E4() NOOP
#define enable_E5() NOOP #define enable_E5() NOOP
#define disable_E5() NOOP #define disable_E5() NOOP
#define enable_E6() NOOP
#define disable_E6() NOOP
#define enable_E7() NOOP
#define disable_E7() NOOP
#else // !MIXING_EXTRUDER #else // !MIXING_EXTRUDER
@ -686,4 +894,20 @@ void reset_stepper_drivers(); // Called by settings.load / settings.reset
#define disable_E5() NOOP #define disable_E5() NOOP
#endif #endif
#if E_STEPPERS > 6 && HAS_E6_ENABLE
#define enable_E6() E6_enable()
#define disable_E6() E6_disable()
#else
#define enable_E6() NOOP
#define disable_E6() NOOP
#endif
#if E_STEPPERS > 7 && HAS_E7_ENABLE
#define enable_E7() E7_enable()
#define disable_E7() E7_disable()
#else
#define enable_E7() NOOP
#define disable_E7() NOOP
#endif
#endif // !MIXING_EXTRUDER #endif // !MIXING_EXTRUDER

View File

@ -301,6 +301,20 @@ enum StealthIndex : uint8_t { STEALTH_AXIS_XY, STEALTH_AXIS_Z, STEALTH_AXIS_E };
TMC_UART_DEFINE_E(SW, 5); TMC_UART_DEFINE_E(SW, 5);
#endif #endif
#endif #endif
#if AXIS_HAS_UART(E6)
#ifdef E6_HARDWARE_SERIAL
TMC_UART_DEFINE_E(HW, 6);
#else
TMC_UART_DEFINE_E(SW, 6);
#endif
#endif
#if AXIS_HAS_UART(E7)
#ifdef E7_HARDWARE_SERIAL
TMC_UART_DEFINE_E(HW, 7);
#else
TMC_UART_DEFINE_E(SW, 7);
#endif
#endif
void tmc_serial_begin() { void tmc_serial_begin() {
#if AXIS_HAS_UART(X) #if AXIS_HAS_UART(X)
@ -401,6 +415,20 @@ enum StealthIndex : uint8_t { STEALTH_AXIS_XY, STEALTH_AXIS_Z, STEALTH_AXIS_E };
stepperE5.beginSerial(TMC_BAUD_RATE); stepperE5.beginSerial(TMC_BAUD_RATE);
#endif #endif
#endif #endif
#if AXIS_HAS_UART(E6)
#ifdef E6_HARDWARE_SERIAL
E6_HARDWARE_SERIAL.begin(TMC_BAUD_RATE);
#else
stepperE6.beginSerial(TMC_BAUD_RATE);
#endif
#endif
#if AXIS_HAS_UART(E7)
#ifdef E7_HARDWARE_SERIAL
E7_HARDWARE_SERIAL.begin(TMC_BAUD_RATE);
#else
stepperE7.beginSerial(TMC_BAUD_RATE);
#endif
#endif
} }
#endif #endif
@ -654,6 +682,12 @@ void restore_trinamic_drivers() {
#if AXIS_IS_TMC(E5) #if AXIS_IS_TMC(E5)
stepperE5.push(); stepperE5.push();
#endif #endif
#if AXIS_IS_TMC(E6)
stepperE6.push();
#endif
#if AXIS_IS_TMC(E7)
stepperE7.push();
#endif
} }
void reset_trinamic_drivers() { void reset_trinamic_drivers() {
@ -719,6 +753,12 @@ void reset_trinamic_drivers() {
#if AXIS_IS_TMC(E5) #if AXIS_IS_TMC(E5)
_TMC_INIT(E5, STEALTH_AXIS_E); _TMC_INIT(E5, STEALTH_AXIS_E);
#endif #endif
#if AXIS_IS_TMC(E6)
_TMC_INIT(E6, STEALTH_AXIS_E);
#endif
#if AXIS_IS_TMC(E7)
_TMC_INIT(E7, STEALTH_AXIS_E);
#endif
#if USE_SENSORLESS #if USE_SENSORLESS
#if X_SENSORLESS #if X_SENSORLESS

View File

@ -58,6 +58,8 @@
#define TMC_E3_LABEL 'E', '3' #define TMC_E3_LABEL 'E', '3'
#define TMC_E4_LABEL 'E', '4' #define TMC_E4_LABEL 'E', '4'
#define TMC_E5_LABEL 'E', '5' #define TMC_E5_LABEL 'E', '5'
#define TMC_E6_LABEL 'E', '6'
#define TMC_E7_LABEL 'E', '7'
#define __TMC_CLASS(TYPE, L, I, A) TMCMarlin<CLASS_##TYPE, L, I, A> #define __TMC_CLASS(TYPE, L, I, A) TMCMarlin<CLASS_##TYPE, L, I, A>
#define _TMC_CLASS(TYPE, LandI, A) __TMC_CLASS(TYPE, LandI, A) #define _TMC_CLASS(TYPE, LandI, A) __TMC_CLASS(TYPE, LandI, A)
@ -266,3 +268,29 @@ void reset_trinamic_drivers();
#define E5_STEP_WRITE(STATE) do{ if(STATE) TOGGLE(E5_STEP_PIN); }while(0) #define E5_STEP_WRITE(STATE) do{ if(STATE) TOGGLE(E5_STEP_PIN); }while(0)
#endif #endif
#endif #endif
// E6 Stepper
#if AXIS_IS_TMC(E6)
extern TMC_CLASS_E(6) stepperE6;
#if ENABLED(SOFTWARE_DRIVER_ENABLE) && AXIS_IS_TMC(E6)
#define E6_ENABLE_INIT() NOOP
#define E6_ENABLE_WRITE(STATE) stepperE6.toff((STATE)==E_ENABLE_ON ? chopper_timing.toff : 0)
#define E6_ENABLE_READ() stepperE6.isEnabled()
#endif
#if AXIS_HAS_SQUARE_WAVE(E6)
#define E6_STEP_WRITE(STATE) do{ if(STATE) TOGGLE(E6_STEP_PIN); }while(0)
#endif
#endif
// E7 Stepper
#if AXIS_IS_TMC(E7)
extern TMC_CLASS_E(7) stepperE7;
#if ENABLED(SOFTWARE_DRIVER_ENABLE) && AXIS_IS_TMC(E7)
#define E7_ENABLE_INIT() NOOP
#define E7_ENABLE_WRITE(STATE) stepperE7.toff((STATE)==E_ENABLE_ON ? chopper_timing.toff : 0)
#define E7_ENABLE_READ() stepperE7.isEnabled()
#endif
#if AXIS_HAS_SQUARE_WAVE(E7)
#define E7_STEP_WRITE(STATE) do{ if(STATE) TOGGLE(E7_STEP_PIN); }while(0)
#endif
#endif

View File

@ -303,9 +303,11 @@ volatile bool Temperature::temp_meas_ready = false;
sensor_heater_2 { HEATER_2_RAW_LO_TEMP, HEATER_2_RAW_HI_TEMP, 0, 16383 }, sensor_heater_2 { HEATER_2_RAW_LO_TEMP, HEATER_2_RAW_HI_TEMP, 0, 16383 },
sensor_heater_3 { HEATER_3_RAW_LO_TEMP, HEATER_3_RAW_HI_TEMP, 0, 16383 }, sensor_heater_3 { HEATER_3_RAW_LO_TEMP, HEATER_3_RAW_HI_TEMP, 0, 16383 },
sensor_heater_4 { HEATER_4_RAW_LO_TEMP, HEATER_4_RAW_HI_TEMP, 0, 16383 }, sensor_heater_4 { HEATER_4_RAW_LO_TEMP, HEATER_4_RAW_HI_TEMP, 0, 16383 },
sensor_heater_5 { HEATER_5_RAW_LO_TEMP, HEATER_5_RAW_HI_TEMP, 0, 16383 }; sensor_heater_5 { HEATER_5_RAW_LO_TEMP, HEATER_5_RAW_HI_TEMP, 0, 16383 },
sensor_heater_6 { HEATER_6_RAW_LO_TEMP, HEATER_6_RAW_HI_TEMP, 0, 16383 },
sensor_heater_7 { HEATER_7_RAW_LO_TEMP, HEATER_7_RAW_HI_TEMP, 0, 16383 };
temp_range_t Temperature::temp_range[HOTENDS] = ARRAY_BY_HOTENDS(sensor_heater_0, sensor_heater_1, sensor_heater_2, sensor_heater_3, sensor_heater_4, sensor_heater_5); temp_range_t Temperature::temp_range[HOTENDS] = ARRAY_BY_HOTENDS(sensor_heater_0, sensor_heater_1, sensor_heater_2, sensor_heater_3, sensor_heater_4, sensor_heater_5, sensor_heater_6, sensor_heater_7);
#endif #endif
#ifdef MAX_CONSECUTIVE_LOW_TEMPERATURE_ERROR_ALLOWED #ifdef MAX_CONSECUTIVE_LOW_TEMPERATURE_ERROR_ALLOWED
@ -686,6 +688,12 @@ int16_t Temperature::getHeaterPower(const heater_ind_t heater_id) {
, REPEAT2(4,_EFAN,4) 4 , REPEAT2(4,_EFAN,4) 4
#if HOTENDS > 5 #if HOTENDS > 5
, REPEAT2(5,_EFAN,5) 5 , REPEAT2(5,_EFAN,5) 5
#if HOTENDS > 6
, REPEAT2(6,_EFAN,6) 6
#if HOTENDS > 7
, REPEAT2(7,_EFAN,7) 7
#endif
#endif
#endif #endif
#endif #endif
#endif #endif
@ -751,6 +759,12 @@ int16_t Temperature::getHeaterPower(const heater_ind_t heater_id) {
#if HAS_AUTO_FAN_5 #if HAS_AUTO_FAN_5
case 5: _UPDATE_AUTO_FAN(E5, fan_on, EXTRUDER_AUTO_FAN_SPEED); break; case 5: _UPDATE_AUTO_FAN(E5, fan_on, EXTRUDER_AUTO_FAN_SPEED); break;
#endif #endif
#if HAS_AUTO_FAN_6
case 6: _UPDATE_AUTO_FAN(E6, fan_on, EXTRUDER_AUTO_FAN_SPEED); break;
#endif
#if HAS_AUTO_FAN_7
case 7: _UPDATE_AUTO_FAN(E7, fan_on, EXTRUDER_AUTO_FAN_SPEED); break;
#endif
#if HAS_AUTO_CHAMBER_FAN && !AUTO_CHAMBER_IS_E #if HAS_AUTO_CHAMBER_FAN && !AUTO_CHAMBER_IS_E
case CHAMBER_FAN_INDEX: _UPDATE_AUTO_FAN(CHAMBER, fan_on, CHAMBER_AUTO_FAN_SPEED); break; case CHAMBER_FAN_INDEX: _UPDATE_AUTO_FAN(CHAMBER, fan_on, CHAMBER_AUTO_FAN_SPEED); break;
#endif #endif
@ -893,7 +907,6 @@ void Temperature::min_temp_error(const heater_ind_t heater) {
pid_output += work_pid[ee].Kc; pid_output += work_pid[ee].Kc;
} }
#endif // PID_EXTRUSION_SCALING #endif // PID_EXTRUSION_SCALING
#if ENABLED(PID_FAN_SCALING) #if ENABLED(PID_FAN_SCALING)
if (thermalManager.fan_speed[active_extruder] > PID_FAN_SCALING_MIN_SPEED) { if (thermalManager.fan_speed[active_extruder] > PID_FAN_SCALING_MIN_SPEED) {
work_pid[ee].Kf = PID_PARAM(Kf, ee) + (PID_FAN_SCALING_LIN_FACTOR) * thermalManager.fan_speed[active_extruder]; work_pid[ee].Kf = PID_PARAM(Kf, ee) + (PID_FAN_SCALING_LIN_FACTOR) * thermalManager.fan_speed[active_extruder];
@ -902,7 +915,6 @@ void Temperature::min_temp_error(const heater_ind_t heater) {
//pid_output -= work_pid[ee].Ki; //pid_output -= work_pid[ee].Ki;
//pid_output += work_pid[ee].Ki * work_pid[ee].Kf //pid_output += work_pid[ee].Ki * work_pid[ee].Kf
#endif // PID_FAN_SCALING #endif // PID_FAN_SCALING
LIMIT(pid_output, 0, PID_MAX); LIMIT(pid_output, 0, PID_MAX);
} }
temp_dState[ee] = temp_hotend[ee].celsius; temp_dState[ee] = temp_hotend[ee].celsius;
@ -1286,6 +1298,12 @@ void Temperature::manage_heater() {
#if ENABLED(HEATER_5_USER_THERMISTOR) #if ENABLED(HEATER_5_USER_THERMISTOR)
{ true, 0, 0, HOTEND5_PULLUP_RESISTOR_OHMS, HOTEND5_RESISTANCE_25C_OHMS, 0, 0, HOTEND5_BETA, 0 }, { true, 0, 0, HOTEND5_PULLUP_RESISTOR_OHMS, HOTEND5_RESISTANCE_25C_OHMS, 0, 0, HOTEND5_BETA, 0 },
#endif #endif
#if ENABLED(HEATER_6_USER_THERMISTOR)
{ true, 0, 0, HOTEND6_PULLUP_RESISTOR_OHMS, HOTEND6_RESISTANCE_25C_OHMS, 0, 0, HOTEND6_BETA, 0 },
#endif
#if ENABLED(HEATER_7_USER_THERMISTOR)
{ true, 0, 0, HOTEND7_PULLUP_RESISTOR_OHMS, HOTEND7_RESISTANCE_25C_OHMS, 0, 0, HOTEND7_BETA, 0 },
#endif
#if ENABLED(HEATER_BED_USER_THERMISTOR) #if ENABLED(HEATER_BED_USER_THERMISTOR)
{ true, 0, 0, BED_PULLUP_RESISTOR_OHMS, BED_RESISTANCE_25C_OHMS, 0, 0, BED_BETA, 0 }, { true, 0, 0, BED_PULLUP_RESISTOR_OHMS, BED_RESISTANCE_25C_OHMS, 0, 0, BED_BETA, 0 },
#endif #endif
@ -1331,6 +1349,12 @@ void Temperature::manage_heater() {
#if ENABLED(HEATER_5_USER_THERMISTOR) #if ENABLED(HEATER_5_USER_THERMISTOR)
t_index == CTI_HOTEND_5 ? PSTR("HOTEND 5") : t_index == CTI_HOTEND_5 ? PSTR("HOTEND 5") :
#endif #endif
#if ENABLED(HEATER_6_USER_THERMISTOR)
t_index == CTI_HOTEND_6 ? PSTR("HOTEND 6") :
#endif
#if ENABLED(HEATER_7_USER_THERMISTOR)
t_index == CTI_HOTEND_7 ? PSTR("HOTEND 7") :
#endif
#if ENABLED(HEATER_BED_USER_THERMISTOR) #if ENABLED(HEATER_BED_USER_THERMISTOR)
t_index == CTI_BED ? PSTR("BED") : t_index == CTI_BED ? PSTR("BED") :
#endif #endif
@ -1476,6 +1500,26 @@ void Temperature::manage_heater() {
#else #else
break; break;
#endif #endif
case 6:
#if ENABLED(HEATER_6_USER_THERMISTOR)
return user_thermistor_to_deg_c(CTI_HOTEND_6, raw);
#elif ENABLED(HEATER_6_USES_AD595)
return TEMP_AD595(raw);
#elif ENABLED(HEATER_6_USES_AD8495)
return TEMP_AD8495(raw);
#else
break;
#endif
case 7:
#if ENABLED(HEATER_7_USER_THERMISTOR)
return user_thermistor_to_deg_c(CTI_HOTEND_7, raw);
#elif ENABLED(HEATER_7_USES_AD595)
return TEMP_AD595(raw);
#elif ENABLED(HEATER_7_USES_AD8495)
return TEMP_AD8495(raw);
#else
break;
#endif
default: break; default: break;
} }
@ -1633,8 +1677,9 @@ void Temperature::init() {
#endif #endif
#if MB(RUMBA) #if MB(RUMBA)
#define _AD(N) (ANY(HEATER_##N##_USES_AD595, HEATER_##N##_USES_AD8495)) #define _AD(N) ANY(HEATER_##N##_USES_AD595, HEATER_##N##_USES_AD8495)
#if _AD(0) || _AD(1) || _AD(2) || _AD(3) || _AD(4) || _AD(5) || _AD(BED) || _AD(CHAMBER) #if _AD(0) || _AD(1) || _AD(2) /* RUMBA has 3 E plugs // || _AD(3) || _AD(4) || _AD(5) || _AD(6) || _AD(7) */ \
|| _AD(BED) || _AD(CHAMBER)
// Disable RUMBA JTAG in case the thermocouple extension is plugged on top of JTAG connector // Disable RUMBA JTAG in case the thermocouple extension is plugged on top of JTAG connector
MCUCR = _BV(JTD); MCUCR = _BV(JTD);
MCUCR = _BV(JTD); MCUCR = _BV(JTD);
@ -1668,6 +1713,12 @@ void Temperature::init() {
#if HAS_HEATER_5 #if HAS_HEATER_5
OUT_WRITE(HEATER_5_PIN, HEATER_5_INVERTING); OUT_WRITE(HEATER_5_PIN, HEATER_5_INVERTING);
#endif #endif
#if HAS_HEATER_6
OUT_WRITE(HEATER_6_PIN, HEATER_6_INVERTING);
#endif
#if HAS_HEATER_7
OUT_WRITE(HEATER_7_PIN, HEATER_7_INVERTING);
#endif
#if HAS_HEATED_BED #if HAS_HEATED_BED
#ifdef ALFAWISE_UX0 #ifdef ALFAWISE_UX0
@ -1690,6 +1741,21 @@ void Temperature::init() {
#if HAS_FAN2 #if HAS_FAN2
INIT_FAN_PIN(FAN2_PIN); INIT_FAN_PIN(FAN2_PIN);
#endif #endif
#if HAS_FAN3
INIT_FAN_PIN(FAN3_PIN);
#endif
#if HAS_FAN4
INIT_FAN_PIN(FAN4_PIN);
#endif
#if HAS_FAN5
INIT_FAN_PIN(FAN5_PIN);
#endif
#if HAS_FAN6
INIT_FAN_PIN(FAN6_PIN);
#endif
#if HAS_FAN7
INIT_FAN_PIN(FAN7_PIN);
#endif
#if ENABLED(USE_CONTROLLER_FAN) #if ENABLED(USE_CONTROLLER_FAN)
INIT_FAN_PIN(CONTROLLER_FAN_PIN); INIT_FAN_PIN(CONTROLLER_FAN_PIN);
#endif #endif
@ -1731,6 +1797,12 @@ void Temperature::init() {
#if HAS_TEMP_ADC_5 #if HAS_TEMP_ADC_5
HAL_ANALOG_SELECT(TEMP_5_PIN); HAL_ANALOG_SELECT(TEMP_5_PIN);
#endif #endif
#if HAS_TEMP_ADC_6
HAL_ANALOG_SELECT(TEMP_6_PIN);
#endif
#if HAS_TEMP_ADC_7
HAL_ANALOG_SELECT(TEMP_7_PIN);
#endif
#if HAS_JOY_ADC_X #if HAS_JOY_ADC_X
HAL_ANALOG_SELECT(JOY_X_PIN); HAL_ANALOG_SELECT(JOY_X_PIN);
#endif #endif
@ -1780,6 +1852,12 @@ void Temperature::init() {
#if HAS_AUTO_FAN_5 && !(_EFANOVERLAP(5,0) || _EFANOVERLAP(5,1) || _EFANOVERLAP(5,2) || _EFANOVERLAP(5,3) || _EFANOVERLAP(5,4)) #if HAS_AUTO_FAN_5 && !(_EFANOVERLAP(5,0) || _EFANOVERLAP(5,1) || _EFANOVERLAP(5,2) || _EFANOVERLAP(5,3) || _EFANOVERLAP(5,4))
INIT_E_AUTO_FAN_PIN(E5_AUTO_FAN_PIN); INIT_E_AUTO_FAN_PIN(E5_AUTO_FAN_PIN);
#endif #endif
#if HAS_AUTO_FAN_6 && !(_EFANOVERLAP(6,0) || _EFANOVERLAP(6,1) || _EFANOVERLAP(6,2) || _EFANOVERLAP(6,3) || _EFANOVERLAP(6,4) || _EFANOVERLAP(6,5))
INIT_E_AUTO_FAN_PIN(E6_AUTO_FAN_PIN);
#endif
#if HAS_AUTO_FAN_7 && !(_EFANOVERLAP(7,0) || _EFANOVERLAP(7,1) || _EFANOVERLAP(7,2) || _EFANOVERLAP(7,3) || _EFANOVERLAP(7,4) || _EFANOVERLAP(7,5) || _EFANOVERLAP(7,6))
INIT_E_AUTO_FAN_PIN(E7_AUTO_FAN_PIN);
#endif
#if HAS_AUTO_CHAMBER_FAN && !AUTO_CHAMBER_IS_E #if HAS_AUTO_CHAMBER_FAN && !AUTO_CHAMBER_IS_E
INIT_CHAMBER_AUTO_FAN_PIN(CHAMBER_AUTO_FAN_PIN); INIT_CHAMBER_AUTO_FAN_PIN(CHAMBER_AUTO_FAN_PIN);
#endif #endif
@ -1841,6 +1919,22 @@ void Temperature::init() {
#ifdef HEATER_5_MAXTEMP #ifdef HEATER_5_MAXTEMP
_TEMP_MAX_E(5); _TEMP_MAX_E(5);
#endif #endif
#if HOTENDS > 6
#ifdef HEATER_6_MINTEMP
_TEMP_MIN_E(6);
#endif
#ifdef HEATER_6_MAXTEMP
_TEMP_MAX_E(6);
#endif
#if HOTENDS > 7
#ifdef HEATER_7_MINTEMP
_TEMP_MIN_E(7);
#endif
#ifdef HEATER_7_MAXTEMP
_TEMP_MAX_E(7);
#endif
#endif // HOTENDS > 7
#endif // HOTENDS > 6
#endif // HOTENDS > 5 #endif // HOTENDS > 5
#endif // HOTENDS > 4 #endif // HOTENDS > 4
#endif // HOTENDS > 3 #endif // HOTENDS > 3
@ -2232,6 +2326,12 @@ void Temperature::set_current_temp_raw() {
temp_hotend[4].update(); temp_hotend[4].update();
#if HAS_TEMP_ADC_5 #if HAS_TEMP_ADC_5
temp_hotend[5].update(); temp_hotend[5].update();
#if HAS_TEMP_ADC_6
temp_hotend[6].update();
#if HAS_TEMP_ADC_7
temp_hotend[7].update();
#endif // HAS_TEMP_ADC_7
#endif // HAS_TEMP_ADC_6
#endif // HAS_TEMP_ADC_5 #endif // HAS_TEMP_ADC_5
#endif // HAS_TEMP_ADC_4 #endif // HAS_TEMP_ADC_4
#endif // HAS_TEMP_ADC_3 #endif // HAS_TEMP_ADC_3
@ -2508,6 +2608,21 @@ void Temperature::tick() {
#if HAS_FAN2 #if HAS_FAN2
_FAN_PWM(2); _FAN_PWM(2);
#endif #endif
#if HAS_FAN3
_FAN_PWM(3);
#endif
#if HAS_FAN4
_FAN_PWM(4);
#endif
#if HAS_FAN5
_FAN_PWM(5);
#endif
#if HAS_FAN6
_FAN_PWM(6);
#endif
#if HAS_FAN7
_FAN_PWM(7);
#endif
#endif #endif
} }
else { else {
@ -2535,6 +2650,21 @@ void Temperature::tick() {
#if HAS_FAN2 #if HAS_FAN2
if (soft_pwm_count_fan[2] <= pwm_count_tmp) WRITE_FAN(2, LOW); if (soft_pwm_count_fan[2] <= pwm_count_tmp) WRITE_FAN(2, LOW);
#endif #endif
#if HAS_FAN3
if (soft_pwm_count_fan[3] <= pwm_count_tmp) WRITE_FAN(3, LOW);
#endif
#if HAS_FAN4
if (soft_pwm_count_fan[4] <= pwm_count_tmp) WRITE_FAN(4, LOW);
#endif
#if HAS_FAN5
if (soft_pwm_count_fan[5] <= pwm_count_tmp) WRITE_FAN(5, LOW);
#endif
#if HAS_FAN6
if (soft_pwm_count_fan[6] <= pwm_count_tmp) WRITE_FAN(6, LOW);
#endif
#if HAS_FAN7
if (soft_pwm_count_fan[7] <= pwm_count_tmp) WRITE_FAN(7, LOW);
#endif
#endif #endif
} }
@ -2599,6 +2729,21 @@ void Temperature::tick() {
#if HAS_FAN2 #if HAS_FAN2
_PWM_FAN(2); _PWM_FAN(2);
#endif #endif
#if HAS_FAN3
_FAN_PWM(3);
#endif
#if HAS_FAN4
_FAN_PWM(4);
#endif
#if HAS_FAN5
_FAN_PWM(5);
#endif
#if HAS_FAN6
_FAN_PWM(6);
#endif
#if HAS_FAN7
_FAN_PWM(7);
#endif
} }
#if HAS_FAN0 #if HAS_FAN0
if (soft_pwm_count_fan[0] <= pwm_count_tmp) WRITE_FAN(0, LOW); if (soft_pwm_count_fan[0] <= pwm_count_tmp) WRITE_FAN(0, LOW);
@ -2609,6 +2754,21 @@ void Temperature::tick() {
#if HAS_FAN2 #if HAS_FAN2
if (soft_pwm_count_fan[2] <= pwm_count_tmp) WRITE_FAN(2, LOW); if (soft_pwm_count_fan[2] <= pwm_count_tmp) WRITE_FAN(2, LOW);
#endif #endif
#if HAS_FAN3
if (soft_pwm_count_fan[3] <= pwm_count_tmp) WRITE_FAN(3, LOW);
#endif
#if HAS_FAN4
if (soft_pwm_count_fan[4] <= pwm_count_tmp) WRITE_FAN(4, LOW);
#endif
#if HAS_FAN5
if (soft_pwm_count_fan[5] <= pwm_count_tmp) WRITE_FAN(5, LOW);
#endif
#if HAS_FAN6
if (soft_pwm_count_fan[6] <= pwm_count_tmp) WRITE_FAN(6, LOW);
#endif
#if HAS_FAN7
if (soft_pwm_count_fan[7] <= pwm_count_tmp) WRITE_FAN(7, LOW);
#endif
#endif // FAN_SOFT_PWM #endif // FAN_SOFT_PWM
// SOFT_PWM_SCALE to frequency: // SOFT_PWM_SCALE to frequency:
@ -2730,6 +2890,16 @@ void Temperature::tick() {
case MeasureTemp_5: ACCUMULATE_ADC(temp_hotend[5]); break; case MeasureTemp_5: ACCUMULATE_ADC(temp_hotend[5]); break;
#endif #endif
#if HAS_TEMP_ADC_6
case PrepareTemp_6: HAL_START_ADC(TEMP_6_PIN); break;
case MeasureTemp_6: ACCUMULATE_ADC(temp_hotend[6]); break;
#endif
#if HAS_TEMP_ADC_7
case PrepareTemp_7: HAL_START_ADC(TEMP_7_PIN); break;
case MeasureTemp_7: ACCUMULATE_ADC(temp_hotend[7]); break;
#endif
#if ENABLED(FILAMENT_WIDTH_SENSOR) #if ENABLED(FILAMENT_WIDTH_SENSOR)
case Prepare_FILWIDTH: HAL_START_ADC(FILWIDTH_PIN); break; case Prepare_FILWIDTH: HAL_START_ADC(FILWIDTH_PIN); break;
case Measure_FILWIDTH: case Measure_FILWIDTH:

View File

@ -132,6 +132,12 @@ enum ADCSensorState : char {
#if HAS_TEMP_ADC_5 #if HAS_TEMP_ADC_5
PrepareTemp_5, MeasureTemp_5, PrepareTemp_5, MeasureTemp_5,
#endif #endif
#if HAS_TEMP_ADC_6
PrepareTemp_6, MeasureTemp_6,
#endif
#if HAS_TEMP_ADC_7
PrepareTemp_7, MeasureTemp_7,
#endif
#if HAS_JOY_ADC_X #if HAS_JOY_ADC_X
PrepareJoy_X, MeasureJoy_X, PrepareJoy_X, MeasureJoy_X,
#endif #endif

View File

@ -39,7 +39,7 @@
#define OV(N) int16_t((N) * (OVERSAMPLENR) * (THERMISTOR_TABLE_SCALE)) #define OV(N) int16_t((N) * (OVERSAMPLENR) * (THERMISTOR_TABLE_SCALE))
#define ANY_THERMISTOR_IS(n) (THERMISTOR_HEATER_0 == n || THERMISTOR_HEATER_1 == n || THERMISTOR_HEATER_2 == n || THERMISTOR_HEATER_3 == n || THERMISTOR_HEATER_4 == n || THERMISTOR_HEATER_5 == n || THERMISTORBED == n || THERMISTORCHAMBER == n || THERMISTORPROBE == n) #define ANY_THERMISTOR_IS(n) (THERMISTOR_HEATER_0 == n || THERMISTOR_HEATER_1 == n || THERMISTOR_HEATER_2 == n || THERMISTOR_HEATER_3 == n || THERMISTOR_HEATER_4 == n || THERMISTOR_HEATER_5 == n || THERMISTOR_HEATER_6 == n || THERMISTOR_HEATER_7 == n || THERMISTORBED == n || THERMISTORCHAMBER == n || THERMISTORPROBE == n)
// Pt1000 and Pt100 handling // Pt1000 and Pt100 handling
// //
@ -235,6 +235,26 @@
#define HEATER_5_TEMPTABLE_LEN 0 #define HEATER_5_TEMPTABLE_LEN 0
#endif #endif
#if THERMISTOR_HEATER_6
#define HEATER_6_TEMPTABLE TT_NAME(THERMISTOR_HEATER_6)
#define HEATER_6_TEMPTABLE_LEN COUNT(HEATER_6_TEMPTABLE)
#elif defined(HEATER_6_USES_THERMISTOR)
#error "No heater 6 thermistor table specified"
#else
#define HEATER_6_TEMPTABLE nullptr
#define HEATER_6_TEMPTABLE_LEN 0
#endif
#if THERMISTOR_HEATER_7
#define HEATER_7_TEMPTABLE TT_NAME(THERMISTOR_HEATER_7)
#define HEATER_7_TEMPTABLE_LEN COUNT(HEATER_7_TEMPTABLE)
#elif defined(HEATER_7_USES_THERMISTOR)
#error "No heater 7 thermistor table specified"
#else
#define HEATER_7_TEMPTABLE nullptr
#define HEATER_7_TEMPTABLE_LEN 0
#endif
#ifdef THERMISTORBED #ifdef THERMISTORBED
#define BED_TEMPTABLE TT_NAME(THERMISTORBED) #define BED_TEMPTABLE TT_NAME(THERMISTORBED)
#define BED_TEMPTABLE_LEN COUNT(BED_TEMPTABLE) #define BED_TEMPTABLE_LEN COUNT(BED_TEMPTABLE)
@ -264,6 +284,7 @@ static_assert(
HEATER_0_TEMPTABLE_LEN < 256 && HEATER_1_TEMPTABLE_LEN < 256 HEATER_0_TEMPTABLE_LEN < 256 && HEATER_1_TEMPTABLE_LEN < 256
&& HEATER_2_TEMPTABLE_LEN < 256 && HEATER_3_TEMPTABLE_LEN < 256 && HEATER_2_TEMPTABLE_LEN < 256 && HEATER_3_TEMPTABLE_LEN < 256
&& HEATER_4_TEMPTABLE_LEN < 256 && HEATER_5_TEMPTABLE_LEN < 256 && HEATER_4_TEMPTABLE_LEN < 256 && HEATER_5_TEMPTABLE_LEN < 256
&& HEATER_6_TEMPTABLE_LEN < 258 && HEATER_7_TEMPTABLE_LEN < 258
&& BED_TEMPTABLE_LEN < 256 && CHAMBER_TEMPTABLE_LEN < 256 && BED_TEMPTABLE_LEN < 256 && CHAMBER_TEMPTABLE_LEN < 256
&& PROBE_TEMPTABLE_LEN < 256, && PROBE_TEMPTABLE_LEN < 256,
"Temperature conversion tables over 255 entries need special consideration." "Temperature conversion tables over 255 entries need special consideration."
@ -326,6 +347,24 @@ static_assert(
#define HEATER_5_RAW_LO_TEMP MAX_RAW_THERMISTOR_VALUE #define HEATER_5_RAW_LO_TEMP MAX_RAW_THERMISTOR_VALUE
#endif #endif
#endif #endif
#ifndef HEATER_6_RAW_HI_TEMP
#if defined(REVERSE_TEMP_SENSOR_RANGE) || !defined(HEATER_6_USES_THERMISTOR)
#define HEATER_6_RAW_HI_TEMP MAX_RAW_THERMISTOR_VALUE
#define HEATER_6_RAW_LO_TEMP 0
#else
#define HEATER_6_RAW_HI_TEMP 0
#define HEATER_6_RAW_LO_TEMP MAX_RAW_THERMISTOR_VALUE
#endif
#endif
#ifndef HEATER_7_RAW_HI_TEMP
#if defined(REVERSE_TEMP_SENSOR_RANGE) || !defined(HEATER_7_USES_THERMISTOR)
#define HEATER_7_RAW_HI_TEMP MAX_RAW_THERMISTOR_VALUE
#define HEATER_7_RAW_LO_TEMP 0
#else
#define HEATER_7_RAW_HI_TEMP 0
#define HEATER_7_RAW_LO_TEMP MAX_RAW_THERMISTOR_VALUE
#endif
#endif
#ifndef HEATER_BED_RAW_HI_TEMP #ifndef HEATER_BED_RAW_HI_TEMP
#if defined(REVERSE_TEMP_SENSOR_RANGE) || !defined(HEATER_BED_USES_THERMISTOR) #if defined(REVERSE_TEMP_SENSOR_RANGE) || !defined(HEATER_BED_USES_THERMISTOR)
#define HEATER_BED_RAW_HI_TEMP MAX_RAW_THERMISTOR_VALUE #define HEATER_BED_RAW_HI_TEMP MAX_RAW_THERMISTOR_VALUE

View File

@ -534,6 +534,8 @@
#include "stm32/pins_STEVAL_3DP001V1.h" // STM32F4 env:STM32F401VE_STEVAL #include "stm32/pins_STEVAL_3DP001V1.h" // STM32F4 env:STM32F401VE_STEVAL
#elif MB(BIGTREE_SKR_PRO_V1_1) #elif MB(BIGTREE_SKR_PRO_V1_1)
#include "stm32/pins_BTT_SKR_PRO_V1_1.h" // STM32F4 env:BIGTREE_SKR_PRO #include "stm32/pins_BTT_SKR_PRO_V1_1.h" // STM32F4 env:BIGTREE_SKR_PRO
#elif MB(BIGTREE_GTR_V1_0)
#include "stm32/pins_BTT_GTR_V1_0.h" // STM32F4 env:BIGTREE_GTR
#elif MB(BIGTREE_BTT002_V1_0) #elif MB(BIGTREE_BTT002_V1_0)
#include "stm32/pins_BTT_BTT002_V1_0.h" // STM32F4 env:BIGTREE_BTT002 #include "stm32/pins_BTT_BTT002_V1_0.h" // STM32F4 env:BIGTREE_BTT002
#elif MB(LERDGE_K) #elif MB(LERDGE_K)
@ -713,6 +715,24 @@
#ifndef E5_MS3_PIN #ifndef E5_MS3_PIN
#define E5_MS3_PIN -1 #define E5_MS3_PIN -1
#endif #endif
#ifndef E6_MS1_PIN
#define E6_MS1_PIN -1
#endif
#ifndef E6_MS2_PIN
#define E6_MS2_PIN -1
#endif
#ifndef E6_MS3_PIN
#define E6_MS3_PIN -1
#endif
#ifndef E7_MS1_PIN
#define E7_MS1_PIN -1
#endif
#ifndef E7_MS2_PIN
#define E7_MS2_PIN -1
#endif
#ifndef E7_MS3_PIN
#define E7_MS3_PIN -1
#endif
#ifndef E0_STEP_PIN #ifndef E0_STEP_PIN
#define E0_STEP_PIN -1 #define E0_STEP_PIN -1
@ -768,6 +788,24 @@
#ifndef E5_ENABLE_PIN #ifndef E5_ENABLE_PIN
#define E5_ENABLE_PIN -1 #define E5_ENABLE_PIN -1
#endif #endif
#ifndef E6_STEP_PIN
#define E6_STEP_PIN -1
#endif
#ifndef E6_DIR_PIN
#define E6_DIR_PIN -1
#endif
#ifndef E6_ENABLE_PIN
#define E6_ENABLE_PIN -1
#endif
#ifndef E7_STEP_PIN
#define E7_STEP_PIN -1
#endif
#ifndef E7_DIR_PIN
#define E7_DIR_PIN -1
#endif
#ifndef E7_ENABLE_PIN
#define E7_ENABLE_PIN -1
#endif
#ifndef X_CS_PIN #ifndef X_CS_PIN
#define X_CS_PIN -1 #define X_CS_PIN -1
@ -796,6 +834,12 @@
#ifndef E5_CS_PIN #ifndef E5_CS_PIN
#define E5_CS_PIN -1 #define E5_CS_PIN -1
#endif #endif
#ifndef E6_CS_PIN
#define E6_CS_PIN -1
#endif
#ifndef E7_CS_PIN
#define E7_CS_PIN -1
#endif
#ifndef FAN_PIN #ifndef FAN_PIN
#define FAN_PIN -1 #define FAN_PIN -1
@ -839,6 +883,12 @@
#ifndef HEATER_5_PIN #ifndef HEATER_5_PIN
#define HEATER_5_PIN -1 #define HEATER_5_PIN -1
#endif #endif
#ifndef HEATER_6_PIN
#define HEATER_6_PIN -1
#endif
#ifndef HEATER_7_PIN
#define HEATER_7_PIN -1
#endif
#ifndef HEATER_BED_PIN #ifndef HEATER_BED_PIN
#define HEATER_BED_PIN -1 #define HEATER_BED_PIN -1
#endif #endif
@ -861,6 +911,12 @@
#ifndef TEMP_5_PIN #ifndef TEMP_5_PIN
#define TEMP_5_PIN -1 #define TEMP_5_PIN -1
#endif #endif
#ifndef TEMP_6_PIN
#define TEMP_6_PIN -1
#endif
#ifndef TEMP_7_PIN
#define TEMP_7_PIN -1
#endif
#ifndef TEMP_BED_PIN #ifndef TEMP_BED_PIN
#define TEMP_BED_PIN -1 #define TEMP_BED_PIN -1
#endif #endif
@ -940,6 +996,20 @@
#define E5_AUTO_FAN_PIN -1 #define E5_AUTO_FAN_PIN -1
#endif #endif
#endif #endif
#ifndef E6_AUTO_FAN_PIN
#ifdef ORIG_E6_AUTO_FAN_PIN
#define E6_AUTO_FAN_PIN ORIG_E6_AUTO_FAN_PIN
#else
#define E6_AUTO_FAN_PIN -1
#endif
#endif
#ifndef E7_AUTO_FAN_PIN
#ifdef ORIG_E7_AUTO_FAN_PIN
#define E7_AUTO_FAN_PIN ORIG_E7_AUTO_FAN_PIN
#else
#define E7_AUTO_FAN_PIN -1
#endif
#endif
#ifndef CHAMBER_AUTO_FAN_PIN #ifndef CHAMBER_AUTO_FAN_PIN
#ifdef ORIG_CHAMBER_AUTO_FAN_PIN #ifdef ORIG_CHAMBER_AUTO_FAN_PIN
#define CHAMBER_AUTO_FAN_PIN ORIG_CHAMBER_AUTO_FAN_PIN #define CHAMBER_AUTO_FAN_PIN ORIG_CHAMBER_AUTO_FAN_PIN

View File

@ -153,6 +153,24 @@
#if !PIN_EXISTS(E5_MS3) #if !PIN_EXISTS(E5_MS3)
#undef E5_MS3_PIN #undef E5_MS3_PIN
#endif #endif
#if !PIN_EXISTS(E6_MS1)
#undef E6_MS1_PIN
#endif
#if !PIN_EXISTS(E6_MS2)
#undef E6_MS2_PIN
#endif
#if !PIN_EXISTS(E6_MS3)
#undef E6_MS3_PIN
#endif
#if !PIN_EXISTS(E7_MS1)
#undef E7_MS1_PIN
#endif
#if !PIN_EXISTS(E7_MS2)
#undef E7_MS2_PIN
#endif
#if !PIN_EXISTS(E7_MS3)
#undef E7_MS3_PIN
#endif
#if !PIN_EXISTS(E0_STEP) #if !PIN_EXISTS(E0_STEP)
#undef E0_STEP_PIN #undef E0_STEP_PIN
@ -208,6 +226,24 @@
#if !PIN_EXISTS(E5_ENABLE) #if !PIN_EXISTS(E5_ENABLE)
#undef E5_ENABLE_PIN #undef E5_ENABLE_PIN
#endif #endif
#if !PIN_EXISTS(E6_STEP)
#undef E6_STEP_PIN
#endif
#if !PIN_EXISTS(E6_DIR)
#undef E6_DIR_PIN
#endif
#if !PIN_EXISTS(E6_ENABLE)
#undef E6_ENABLE_PIN
#endif
#if !PIN_EXISTS(E7_STEP)
#undef E7_STEP_PIN
#endif
#if !PIN_EXISTS(E7_DIR)
#undef E7_DIR_PIN
#endif
#if !PIN_EXISTS(E7_ENABLE)
#undef E7_ENABLE_PIN
#endif
#if !PIN_EXISTS(X_CS) #if !PIN_EXISTS(X_CS)
#undef X_CS_PIN #undef X_CS_PIN
@ -236,6 +272,12 @@
#if !PIN_EXISTS(E5_CS) #if !PIN_EXISTS(E5_CS)
#undef E5_CS_PIN #undef E5_CS_PIN
#endif #endif
#if !PIN_EXISTS(E6_CS)
#undef E6_CS_PIN
#endif
#if !PIN_EXISTS(E7_CS)
#undef E7_CS_PIN
#endif
#if !PIN_EXISTS(FAN) #if !PIN_EXISTS(FAN)
#undef FAN_PIN #undef FAN_PIN
@ -247,6 +289,21 @@
#if !PIN_EXISTS(FAN2) #if !PIN_EXISTS(FAN2)
#undef FAN2_PIN #undef FAN2_PIN
#endif #endif
#if !PIN_EXISTS(FAN3)
#undef FAN3_PIN
#endif
#if !PIN_EXISTS(FAN4)
#undef FAN4_PIN
#endif
#if !PIN_EXISTS(FAN5)
#undef FAN5_PIN
#endif
#if !PIN_EXISTS(FAN6)
#undef FAN6_PIN
#endif
#if !PIN_EXISTS(FAN7)
#undef FAN7_PIN
#endif
#if !PIN_EXISTS(CONTROLLER_FAN) #if !PIN_EXISTS(CONTROLLER_FAN)
#undef CONTROLLER_FAN_PIN #undef CONTROLLER_FAN_PIN
#endif #endif
@ -279,6 +336,12 @@
#if !PIN_EXISTS(HEATER_5) #if !PIN_EXISTS(HEATER_5)
#undef HEATER_5_PIN #undef HEATER_5_PIN
#endif #endif
#if !PIN_EXISTS(HEATER_6)
#undef HEATER_6_PIN
#endif
#if !PIN_EXISTS(HEATER_7)
#undef HEATER_7_PIN
#endif
#if !PIN_EXISTS(HEATER_BED) #if !PIN_EXISTS(HEATER_BED)
#undef HEATER_BED_PIN #undef HEATER_BED_PIN
#endif #endif
@ -301,6 +364,12 @@
#if !PIN_EXISTS(TEMP_5) #if !PIN_EXISTS(TEMP_5)
#undef TEMP_5_PIN #undef TEMP_5_PIN
#endif #endif
#if !PIN_EXISTS(TEMP_6)
#undef TEMP_6_PIN
#endif
#if !PIN_EXISTS(TEMP_7)
#undef TEMP_7_PIN
#endif
#if !PIN_EXISTS(TEMP_BED) #if !PIN_EXISTS(TEMP_BED)
#undef TEMP_BED_PIN #undef TEMP_BED_PIN
#endif #endif
@ -363,6 +432,12 @@
#if PIN_EXISTS(TEMP_5) && TEMP_5_PIN < NUM_ANALOG_INPUTS #if PIN_EXISTS(TEMP_5) && TEMP_5_PIN < NUM_ANALOG_INPUTS
REPORT_NAME_ANALOG(__LINE__, TEMP_5_PIN) REPORT_NAME_ANALOG(__LINE__, TEMP_5_PIN)
#endif #endif
#if PIN_EXISTS(TEMP_6) && TEMP_6_PIN < NUM_ANALOG_INPUTS
REPORT_NAME_ANALOG(__LINE__, TEMP_6_PIN)
#endif
#if PIN_EXISTS(TEMP_7) && TEMP_7_PIN < NUM_ANALOG_INPUTS
REPORT_NAME_ANALOG(__LINE__, TEMP_7_PIN)
#endif
#if PIN_EXISTS(TEMP_BED) && TEMP_BED_PIN < NUM_ANALOG_INPUTS #if PIN_EXISTS(TEMP_BED) && TEMP_BED_PIN < NUM_ANALOG_INPUTS
REPORT_NAME_ANALOG(__LINE__, TEMP_BED_PIN) REPORT_NAME_ANALOG(__LINE__, TEMP_BED_PIN)
#endif #endif
@ -686,6 +761,54 @@
#if PIN_EXISTS(E5_STEP) #if PIN_EXISTS(E5_STEP)
REPORT_NAME_DIGITAL(__LINE__, E5_STEP_PIN) REPORT_NAME_DIGITAL(__LINE__, E5_STEP_PIN)
#endif #endif
#if PIN_EXISTS(E6_AUTO_FAN)
REPORT_NAME_DIGITAL(__LINE__, E6_AUTO_FAN_PIN)
#endif
#if PIN_EXISTS(E6_CS)
REPORT_NAME_DIGITAL(__LINE__, E6_CS_PIN)
#endif
#if PIN_EXISTS(E6_DIR)
REPORT_NAME_DIGITAL(__LINE__, E6_DIR_PIN)
#endif
#if PIN_EXISTS(E6_ENABLE)
REPORT_NAME_DIGITAL(__LINE__, E6_ENABLE_PIN)
#endif
#if PIN_EXISTS(E6_MS1)
REPORT_NAME_DIGITAL(__LINE__, E6_MS1_PIN)
#endif
#if PIN_EXISTS(E6_MS2)
REPORT_NAME_DIGITAL(__LINE__, E6_MS2_PIN)
#endif
#if PIN_EXISTS(E6_MS3)
REPORT_NAME_DIGITAL(__LINE__, E6_MS3_PIN)
#endif
#if PIN_EXISTS(E6_STEP)
REPORT_NAME_DIGITAL(__LINE__, E6_STEP_PIN)
#endif
#if PIN_EXISTS(E7_AUTO_FAN)
REPORT_NAME_DIGITAL(__LINE__, E7_AUTO_FAN_PIN)
#endif
#if PIN_EXISTS(E7_CS)
REPORT_NAME_DIGITAL(__LINE__, E7_CS_PIN)
#endif
#if PIN_EXISTS(E7_DIR)
REPORT_NAME_DIGITAL(__LINE__, E7_DIR_PIN)
#endif
#if PIN_EXISTS(E7_ENABLE)
REPORT_NAME_DIGITAL(__LINE__, E7_ENABLE_PIN)
#endif
#if PIN_EXISTS(E7_MS1)
REPORT_NAME_DIGITAL(__LINE__, E7_MS1_PIN)
#endif
#if PIN_EXISTS(E7_MS2)
REPORT_NAME_DIGITAL(__LINE__, E7_MS2_PIN)
#endif
#if PIN_EXISTS(E7_MS3)
REPORT_NAME_DIGITAL(__LINE__, E7_MS3_PIN)
#endif
#if PIN_EXISTS(E7_STEP)
REPORT_NAME_DIGITAL(__LINE__, E7_STEP_PIN)
#endif
#if defined(ENET_CRS) && ENET_CRS >= 0 #if defined(ENET_CRS) && ENET_CRS >= 0
REPORT_NAME_DIGITAL(__LINE__, ENET_CRS) REPORT_NAME_DIGITAL(__LINE__, ENET_CRS)
#endif #endif
@ -765,6 +888,18 @@
#if PIN_EXISTS(FAN3) #if PIN_EXISTS(FAN3)
REPORT_NAME_DIGITAL(__LINE__, FAN3_PIN) REPORT_NAME_DIGITAL(__LINE__, FAN3_PIN)
#endif #endif
#if PIN_EXISTS(FAN4)
REPORT_NAME_DIGITAL(__LINE__, FAN4_PIN)
#endif
#if PIN_EXISTS(FAN5)
REPORT_NAME_DIGITAL(__LINE__, FAN5_PIN)
#endif
#if PIN_EXISTS(FAN6)
REPORT_NAME_DIGITAL(__LINE__, FAN6_PIN)
#endif
#if PIN_EXISTS(FAN7)
REPORT_NAME_DIGITAL(__LINE__, FAN7_PIN)
#endif
#if PIN_EXISTS(FIL_RUNOUT) #if PIN_EXISTS(FIL_RUNOUT)
REPORT_NAME_DIGITAL(__LINE__, FIL_RUNOUT_PIN) REPORT_NAME_DIGITAL(__LINE__, FIL_RUNOUT_PIN)
#endif #endif
@ -936,6 +1071,12 @@
#if PIN_EXISTS(ORIG_E5_AUTO_FAN) #if PIN_EXISTS(ORIG_E5_AUTO_FAN)
REPORT_NAME_DIGITAL(__LINE__, ORIG_E5_AUTO_FAN_PIN) REPORT_NAME_DIGITAL(__LINE__, ORIG_E5_AUTO_FAN_PIN)
#endif #endif
#if PIN_EXISTS(ORIG_E6_AUTO_FAN)
REPORT_NAME_DIGITAL(__LINE__, ORIG_E6_AUTO_FAN_PIN)
#endif
#if PIN_EXISTS(ORIG_E7_AUTO_FAN)
REPORT_NAME_DIGITAL(__LINE__, ORIG_E7_AUTO_FAN_PIN)
#endif
#if PIN_EXISTS(PHOTOGRAPH) #if PIN_EXISTS(PHOTOGRAPH)
REPORT_NAME_DIGITAL(__LINE__, PHOTOGRAPH_PIN) REPORT_NAME_DIGITAL(__LINE__, PHOTOGRAPH_PIN)
#endif #endif
@ -1455,6 +1596,18 @@
#if PIN_EXISTS(E5_SERIAL_RX) #if PIN_EXISTS(E5_SERIAL_RX)
REPORT_NAME_DIGITAL(__LINE__, E5_SERIAL_RX_PIN) REPORT_NAME_DIGITAL(__LINE__, E5_SERIAL_RX_PIN)
#endif #endif
#if PIN_EXISTS(E6_SERIAL_TX)
REPORT_NAME_DIGITAL(__LINE__, E6_SERIAL_TX_PIN)
#endif
#if PIN_EXISTS(E6_SERIAL_RX)
REPORT_NAME_DIGITAL(__LINE__, E6_SERIAL_RX_PIN)
#endif
#if PIN_EXISTS(E7_SERIAL_TX)
REPORT_NAME_DIGITAL(__LINE__, E7_SERIAL_TX_PIN)
#endif
#if PIN_EXISTS(E7_SERIAL_RX)
REPORT_NAME_DIGITAL(__LINE__, E7_SERIAL_RX_PIN)
#endif
#if PIN_EXISTS(L6470_CHAIN_SCK) #if PIN_EXISTS(L6470_CHAIN_SCK)
REPORT_NAME_DIGITAL(__LINE__, L6470_CHAIN_SCK_PIN) REPORT_NAME_DIGITAL(__LINE__, L6470_CHAIN_SCK_PIN)
#endif #endif

View File

@ -277,6 +277,54 @@
#endif #endif
#endif #endif
#define _E6_CS
#define _E6_MS2
#define _E6_MS3
#define _E6_MS4
#if E_NEEDED(6)
#if PIN_EXISTS(E6_CS) && AXIS_HAS_SPI(E6)
#undef _E6_CS
#define _E6_CS E6_CS_PIN,
#endif
#if PIN_EXISTS(E6_MS2)
#undef _E6_MS2
#define _E6_MS2 E6_MS2_PIN,
#endif
#if PIN_EXISTS(E6_MS3)
#undef _E6_MS3
#define _E6_MS3 E6_MS3_PIN,
#endif
#if PIN_EXISTS(E6_MS4)
#undef _E6_MS4
#define _E6_MS4 E6_MS4_PIN,
#endif
#endif
#define _E7_CS
#define _E7_MS3
#define _E7_MS4
#define _E7_MS5
#if E_NEEDED(7)
#if PIN_EXISTS(E7_CS) && AXIS_HAS_SPI(E7)
#undef _E7_CS
#define _E7_CS E7_CS_PIN,
#endif
#if PIN_EXISTS(E7_MS3)
#undef _E7_MS3
#define _E7_MS3 E7_MS3_PIN,
#endif
#if PIN_EXISTS(E7_MS4)
#undef _E7_MS4
#define _E7_MS4 E7_MS4_PIN,
#endif
#if PIN_EXISTS(E7_MS5)
#undef _E7_MS5
#define _E7_MS5 E7_MS5_PIN,
#endif
#endif
// //
// E Steppers // E Steppers
// //
@ -287,6 +335,8 @@
#define _E3_PINS #define _E3_PINS
#define _E4_PINS #define _E4_PINS
#define _E5_PINS #define _E5_PINS
#define _E6_PINS
#define _E7_PINS
#if EXTRUDERS #if EXTRUDERS
#undef _E0_PINS #undef _E0_PINS
@ -303,7 +353,9 @@
#define _E2_PINS E2_STEP_PIN, E2_DIR_PIN, E2_ENABLE_PIN, _E2_CS _E2_MS1 _E2_MS2 _E2_MS3 #define _E2_PINS E2_STEP_PIN, E2_DIR_PIN, E2_ENABLE_PIN, _E2_CS _E2_MS1 _E2_MS2 _E2_MS3
#endif #endif
#endif #endif
#elif EXTRUDERS > 1 || ENABLED(MIXING_EXTRUDER) #elif EXTRUDERS > 1 || ENABLED(MIXING_EXTRUDER)
#undef _E1_PINS #undef _E1_PINS
#define _E1_PINS E1_STEP_PIN, E1_DIR_PIN, E1_ENABLE_PIN, _E1_CS _E1_MS1 _E1_MS2 _E1_MS3 #define _E1_PINS E1_STEP_PIN, E1_DIR_PIN, E1_ENABLE_PIN, _E1_CS _E1_MS1 _E1_MS2 _E1_MS3
#if EXTRUDERS > 2 || (ENABLED(MIXING_EXTRUDER) && MIXING_STEPPERS > 2) #if EXTRUDERS > 2 || (ENABLED(MIXING_EXTRUDER) && MIXING_STEPPERS > 2)
@ -318,10 +370,19 @@
#if EXTRUDERS > 5 || (ENABLED(MIXING_EXTRUDER) && MIXING_STEPPERS > 5) #if EXTRUDERS > 5 || (ENABLED(MIXING_EXTRUDER) && MIXING_STEPPERS > 5)
#undef _E5_PINS #undef _E5_PINS
#define _E5_PINS E5_STEP_PIN, E5_DIR_PIN, E5_ENABLE_PIN, _E5_CS _E5_MS1 _E5_MS2 _E5_MS3 #define _E5_PINS E5_STEP_PIN, E5_DIR_PIN, E5_ENABLE_PIN, _E5_CS _E5_MS1 _E5_MS2 _E5_MS3
#if EXTRUDERS > 6 || (ENABLED(MIXING_EXTRUDER) && MIXING_STEPPERS > 6)
#undef _E6_PINS
#define _E6_PINS E6_STEP_PIN, E6_DIR_PIN, E6_ENABLE_PIN, _E6_CS _E6_MS1 _E6_MS2 _E6_MS3
#if EXTRUDERS > 7 || (ENABLED(MIXING_EXTRUDER) && MIXING_STEPPERS > 7)
#undef _E7_PINS
#define _E7_PINS E7_STEP_PIN, E7_DIR_PIN, E7_ENABLE_PIN, _E7_CS _E7_MS1 _E7_MS2 _E7_MS3
#endif // EXTRUDERS > 7 || MIXING_EXTRUDER > 7
#endif // EXTRUDERS > 6 || MIXING_EXTRUDER > 6
#endif // EXTRUDERS > 5 || MIXING_EXTRUDER > 5 #endif // EXTRUDERS > 5 || MIXING_EXTRUDER > 5
#endif // EXTRUDERS > 4 || MIXING_EXTRUDER > 4 #endif // EXTRUDERS > 4 || MIXING_EXTRUDER > 4
#endif // EXTRUDERS > 3 || MIXING_EXTRUDER > 3 #endif // EXTRUDERS > 3 || MIXING_EXTRUDER > 3
#endif // EXTRUDERS > 2 || MIXING_EXTRUDER > 2 #endif // EXTRUDERS > 2 || MIXING_EXTRUDER > 2
#endif // EXTRUDERS > 1 || MIXING_EXTRUDER #endif // EXTRUDERS > 1 || MIXING_EXTRUDER
// //
@ -334,6 +395,8 @@
#define _H3_PINS #define _H3_PINS
#define _H4_PINS #define _H4_PINS
#define _H5_PINS #define _H5_PINS
#define _H6_PINS
#define _H7_PINS
#if HOTENDS #if HOTENDS
#undef _H0_PINS #undef _H0_PINS
@ -353,6 +416,14 @@
#if HOTENDS > 5 #if HOTENDS > 5
#undef _H5_PINS #undef _H5_PINS
#define _H5_PINS HEATER_5_PIN, E5_AUTO_FAN_PIN, analogInputToDigitalPin(TEMP_5_PIN), #define _H5_PINS HEATER_5_PIN, E5_AUTO_FAN_PIN, analogInputToDigitalPin(TEMP_5_PIN),
#if HOTENDS > 6
#undef _H6_PINS
#define _H6_PINS HEATER_6_PIN, E6_AUTO_FAN_PIN, analogInputToDigitalPin(TEMP_6_PIN),
#if HOTENDS > 7
#undef _H7_PINS
#define _H7_PINS HEATER_7_PIN, E7_AUTO_FAN_PIN, analogInputToDigitalPin(TEMP_7_PIN),
#endif // HOTENDS > 7
#endif // HOTENDS > 6
#endif // HOTENDS > 5 #endif // HOTENDS > 5
#endif // HOTENDS > 4 #endif // HOTENDS > 4
#endif // HOTENDS > 3 #endif // HOTENDS > 3
@ -539,6 +610,31 @@
#else #else
#define _FAN2 #define _FAN2
#endif #endif
#if PIN_EXISTS(FAN3)
#define _FAN3 FAN3_PIN,
#else
#define _FAN3
#endif
#if PIN_EXISTS(FAN4)
#define _FAN4 FAN4_PIN,
#else
#define _FAN4
#endif
#if PIN_EXISTS(FAN5)
#define _FAN5 FAN5_PIN,
#else
#define _FAN5
#endif
#if PIN_EXISTS(FAN6)
#define _FAN6 FAN6_PIN,
#else
#define _FAN6
#endif
#if PIN_EXISTS(FAN7)
#define _FAN7 FAN7_PIN,
#else
#define _FAN7
#endif
#if PIN_EXISTS(CONTROLLER_FAN) #if PIN_EXISTS(CONTROLLER_FAN)
#define _FANC CONTROLLER_FAN_PIN, #define _FANC CONTROLLER_FAN_PIN,
#else #else
@ -550,9 +646,9 @@
#endif #endif
#define SENSITIVE_PINS { \ #define SENSITIVE_PINS { \
_X_PINS _Y_PINS _Z_PINS _X2_PINS _Y2_PINS _Z2_PINS _Z3_PINS _Z4_PINS \ _X_PINS _Y_PINS _Z_PINS _X2_PINS _Y2_PINS _Z2_PINS _Z3_PINS _Z4_PINS _Z_PROBE \
_Z_PROBE _E0_PINS _E1_PINS _E2_PINS _E3_PINS _E4_PINS _E5_PINS \ _E0_PINS _E1_PINS _E2_PINS _E3_PINS _E4_PINS _E5_PINS _E6_PINS _E7_PINS _BED_PINS \
_BED_PINS _H0_PINS _H1_PINS _H2_PINS _H3_PINS _H4_PINS _H5_PINS \ _H0_PINS _H1_PINS _H2_PINS _H3_PINS _H4_PINS _H5_PINS _H6_PINS _H7_PINS \
_PS_ON _HEATER_BED _FAN0 _FAN1 _FAN2 _FANC \ _PS_ON _HEATER_BED _FAN0 _FAN1 _FAN2 _FAN3 _FAN4 _FAN5 _FAN6 _FAN7 _FANC \
HAL_SENSITIVE_PINS \ HAL_SENSITIVE_PINS \
} }

View File

@ -0,0 +1,391 @@
/**
* Marlin 3D Printer Firmware
* Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
*
* Based on Sprinter and grbl.
* Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <http://www.gnu.org/licenses/>.
*
*/
#pragma once
#ifndef TARGET_STM32F4
#error "Oops! Select an STM32F4 board in 'Tools > Board.'"
#elif HOTENDS > 8 || E_STEPPERS > 8
#error "BIGTREE GTR V1.0 supports up to 8 hotends / E-steppers."
#elif HOTENDS > MAX_EXTRUDERS || E_STEPPERS > MAX_EXTRUDERS
#error "Marlin extruder/hotends limit! Increase MAX_EXTRUDERS to continue."
#endif
#define BOARD_INFO_NAME "BIGTREE GTR 1.0"
// Use one of these or SDCard-based Emulation will be used
//#define I2C_EEPROM
//#define SRAM_EEPROM_EMULATION // Use BackSRAM-based EEPROM emulation
//#define FLASH_EEPROM_EMULATION // Use Flash-based EEPROM emulation
#define TP // Enable to define servo and probe pins
//
// Servos
//
#if ENABLED(TP)
#define SERVO0_PIN PB11
#endif
#define PS_ON_PIN PH6
//
// Limit Switches
//
#define X_MIN_PIN PF2
#define X_MAX_PIN PG14
#define Y_MIN_PIN PC13
#define Y_MAX_PIN PG9
#define Z_MIN_PIN PE0
#define Z_MAX_PIN PD3
//
// Pins on the extender
//
//#define X_MIN_PIN PI4
//#define X2_MIN_PIN PF12
//#define Y_MIN_PIN PF4
//#define Y2_MIN_PIN PI7
//#define Z_MIN_PIN PF6
#if ENABLED(TP) && !defined(Z_MIN_PROBE_PIN)
#define Z_MIN_PROBE_PIN PH11 // Z Probe must be PH11
#endif
//
// Steppers
//
#define X_STEP_PIN PC15
#define X_DIR_PIN PF0
#define X_ENABLE_PIN PF1
#ifndef X_CS_PIN
#define X_CS_PIN PC14
#endif
#define Y_STEP_PIN PE3
#define Y_DIR_PIN PE2
#define Y_ENABLE_PIN PE4
#ifndef Y_CS_PIN
#define Y_CS_PIN PE1
#endif
#define Z_STEP_PIN PB8
#define Z_DIR_PIN PB7 // PB7
#define Z_ENABLE_PIN PB9
#ifndef Z_CS_PIN
#define Z_CS_PIN PB5
#endif
#define E0_STEP_PIN PG12
#define E0_DIR_PIN PG11
#define E0_ENABLE_PIN PG13
#ifndef E0_CS_PIN
#define E0_CS_PIN PG10
#endif
#define E1_STEP_PIN PD6
#define E1_DIR_PIN PD5
#define E1_ENABLE_PIN PD7
#ifndef E1_CS_PIN
#define E1_CS_PIN PD4
#endif
#define E2_STEP_PIN PD1
#define E2_DIR_PIN PD0
#define E2_ENABLE_PIN PD2
#ifndef E2_CS_PIN
#define E2_CS_PIN PC12
#endif
#define E3_STEP_PIN PF3
#define E3_DIR_PIN PG3
#define E3_ENABLE_PIN PF8
#ifndef E3_CS_PIN
#define E3_CS_PIN PG4
#endif
#define E4_STEP_PIN PD14
#define E4_DIR_PIN PD11
#define E4_ENABLE_PIN PG2
#ifndef E4_CS_PIN
#define E4_CS_PIN PE15
#endif
#define E5_STEP_PIN PE12
#define E5_DIR_PIN PE10
#define E5_ENABLE_PIN PF14
#ifndef E5_CS_PIN
#define E5_CS_PIN PE7
#endif
#define E6_STEP_PIN PG0
#define E6_DIR_PIN PG1
#define E6_ENABLE_PIN PE8
#ifndef E6_CS_PIN
#define E6_CS_PIN PF15
#endif
#define E7_STEP_PIN PH12
#define E7_DIR_PIN PH15
#define E7_ENABLE_PIN PI0
#ifndef E7_CS_PIN
#define E7_CS_PIN PH14
#endif
//
// Software SPI pins for TMC2130 stepper drivers
//
#if ENABLED(TMC_USE_SW_SPI)
#ifndef TMC_SW_MOSI
#define TMC_SW_MOSI PG15
#endif
#ifndef TMC_SW_MISO
#define TMC_SW_MISO PB6
#endif
#ifndef TMC_SW_SCK
#define TMC_SW_SCK PB3
#endif
#endif
#if HAS_TMC220x
/**
* TMC2208/TMC2209 stepper drivers
*
* Hardware serial communication ports.
* If undefined software serial is used according to the pins below
*/
//#define X_HARDWARE_SERIAL Serial
//#define X2_HARDWARE_SERIAL Serial1
//#define Y_HARDWARE_SERIAL Serial1
//#define Y2_HARDWARE_SERIAL Serial1
//#define Z_HARDWARE_SERIAL Serial1
//#define Z2_HARDWARE_SERIAL Serial1
//#define E0_HARDWARE_SERIAL Serial1
//#define E1_HARDWARE_SERIAL Serial1
//#define E2_HARDWARE_SERIAL Serial1
//#define E3_HARDWARE_SERIAL Serial1
//#define E4_HARDWARE_SERIAL Serial1
//#define E5_HARDWARE_SERIAL Serial1
//#define E6_HARDWARE_SERIAL Serial1
//#define E7_HARDWARE_SERIAL Serial1
//
// Software serial
//
#define X_SERIAL_TX_PIN PC14
#define X_SERIAL_RX_PIN PC14
#define Y_SERIAL_TX_PIN PE1
#define Y_SERIAL_RX_PIN PE1
#define Z_SERIAL_TX_PIN PB5
#define Z_SERIAL_RX_PIN PB5
#define E0_SERIAL_TX_PIN PG10
#define E0_SERIAL_RX_PIN PG10
#define E1_SERIAL_TX_PIN PD4
#define E1_SERIAL_RX_PIN PD4
#define E2_SERIAL_TX_PIN PC12
#define E2_SERIAL_RX_PIN PC12
#define E3_SERIAL_TX_PIN PG4
#define E3_SERIAL_RX_PIN PG4
#define E4_SERIAL_TX_PIN PE15
#define E4_SERIAL_RX_PIN PE15
#define E5_SERIAL_TX_PIN PE7
#define E5_SERIAL_RX_PIN PE7
#define E6_SERIAL_TX_PIN PF15
#define E6_SERIAL_RX_PIN PF15
#define E7_SERIAL_TX_PIN PH14
#define E7_SERIAL_RX_PIN PH14
// Reduce baud rate to improve software serial reliability
#define TMC_BAUD_RATE 19200
#endif
//
// Temperature Sensors
//
#define TEMP_0_PIN PC1 // T1 <-> E0
#define TEMP_1_PIN PC2 // T2 <-> E1
#define TEMP_2_PIN PC3 // T3 <-> E2
#define TEMP_3_PIN PA3 // T4 <-> E3
#define TEMP_4_PIN PF9 // T5 <-> E4
#define TEMP_5_PIN PF10 // T6 <-> E5
//#define TEMP_6_PIN PF7 // T7 <-> E6
//#define TEMP_7_PIN PF5 // T8 <-> E7
#define TEMP_BED_PIN PC0 // T0 <-> Bed
// SPI for Max6675 or Max31855 Thermocouple
// Uses a separate SPI bus
// If you have a two-way thermocouple, you can customize two THERMO_CSx_PIN pins (x:1~2)
#define THERMO_SCK_PIN PI1 // SCK
#define THERMO_DO_PIN PI2 // MISO
#define THERMO_CS1_PIN PH9 // CS1
#define THERMO_CS2_PIN PH2 // CS2
#define MAX6675_SS_PIN THERMO_CS1_PIN
#define MAX6675_SS2_PIN THERMO_CS2_PIN
#define MAX6675_SCK_PIN THERMO_SCK_PIN
#define MAX6675_DO_PIN THERMO_DO_PIN
//
// Heaters / Fans
//
#define HEATER_0_PIN PB1 // Heater0
#define HEATER_1_PIN PA1 // Heater1
#define HEATER_2_PIN PB0 // Heater2
#define HEATER_3_PIN PD15 // Heater3
#define HEATER_4_PIN PD13 // Heater4
#define HEATER_5_PIN PD12 // Heater5
//#define HEATER_6_PIN PE13 // Heater6
//#define HEATER_7_PIN PI6 // Heater7
#define HEATER_BED_PIN PA2 // Hotbed
#define FAN_PIN PE5 // Fan0
#define FAN1_PIN PE6 // Fan1
#define FAN2_PIN PC8 // Fan2
#define FAN3_PIN PI5 // Fan3
#define FAN4_PIN PE9 // Fan4
#define FAN5_PIN PE11 // Fan5
//#define FAN6_PIN PC9 // Fan6
//#define FAN7_PIN PE14 // Fan7
//
// By default the onboard SD (SPI1) is enabled
//
#define CUSTOM_SPI_PINS
#if DISABLED(CUSTOM_SPI_PINS)
#define SDSS PB12
#endif
// HAL SPI1 pins group
#if ENABLED(CUSTOM_SPI_PINS)
#define SDSS PA4
#define SD_DETECT_PIN PC4
#define LCD_SDSS PA4
#define SCK_PIN PA5
#define MISO_PIN PA6
#define MOSI_PIN PA7
#define SS_PIN PA4 // Chip select for SD card used by Marlin
#endif
/**
* _____ _____
* NC | · · | GND 5V | · · | GND
* RESET | · · | PB10(SD_DETECT) (LCD_D7) PG5 | · · | PG6 (LCD_D6)
* (MOSI)PB15 | · · | PH10(BTN_EN2) (LCD_D5) PG7 | · · | PG8 (LCD_D4)
* (SD_SS)PB12 | · · | PD10(BTN_EN1) (LCD_RS) PA8 | · · | PC10 (LCD_EN)
* (SCK)PB13 | · · | PB14(MISO) (BTN_ENC) PA15 | · · | PC11 (BEEPER)
*
* EXP2 EXP1
*/
//
// LCDs and Controllers
//
#if HAS_SPI_LCD
#define BEEPER_PIN PC11
#define BTN_ENC PA15
#if ENABLED(CR10_STOCKDISPLAY)
#define LCD_PINS_RS PA8
#define BTN_EN1 PD10
#define BTN_EN2 PH10
#define LCD_PINS_ENABLE PG7
#define LCD_PINS_D4 PG8
//#undef ST7920_DELAY_1
//#undef ST7920_DELAY_2
//#undef ST7920_DELAY_3
#else
#define LCD_PINS_RS PA8
#define BTN_EN1 PD10
#define BTN_EN2 PH10
#if DISABLED(CUSTOM_SPI_PINS)
#define SD_DETECT_PIN PB10
#define LCD_SDSS PB12
#endif
#define LCD_PINS_ENABLE PC10
#define LCD_PINS_D4 PG8
#if ENABLED(FYSETC_MINI_12864)
#define DOGLCD_CS PC10
#define DOGLCD_A0 PA8
//#define LCD_BACKLIGHT_PIN -1
#define LCD_RESET_PIN PG8 // Must be high or open for LCD to operate normally.
#if EITHER(FYSETC_MINI_12864_1_2, FYSETC_MINI_12864_2_0)
#ifndef RGB_LED_R_PIN
#define RGB_LED_R_PIN PG7
#endif
#ifndef RGB_LED_G_PIN
#define RGB_LED_G_PIN PG6
#endif
#ifndef RGB_LED_B_PIN
#define RGB_LED_B_PIN PG5
#endif
#elif ENABLED(FYSETC_MINI_12864_2_1)
#define NEOPIXEL_PIN PF13
#endif
#endif // !FYSETC_MINI_12864
#if ENABLED(ULTIPANEL)
#define LCD_PINS_D5 PG7
#define LCD_PINS_D6 PG6
#define LCD_PINS_D7 PG5
#endif
#endif
// Alter timing for graphical display
#if HAS_GRAPHICAL_LCD
#define BOARD_ST7920_DELAY_1 DELAY_NS(96)
#define BOARD_ST7920_DELAY_2 DELAY_NS(48)
#define BOARD_ST7920_DELAY_3 DELAY_NS(600)
#endif
//#define DOGLCD_CS PB12
//#define DOGLCD_A0 PA8
//#define LCD_PINS_DC PB14
//#define DOGLCD_MOSI PB15
#endif // HAS_SPI_LCD

View File

@ -91,8 +91,13 @@ const PinMap PinMap_I2C_SDA[] = {
{PB_11, I2C2, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_I2C2)}, {PB_11, I2C2, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_I2C2)},
{PC_9, I2C3, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_I2C3)}, {PC_9, I2C3, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_I2C3)},
#if STM32F4X_PIN_NUM >= 144 // 144 pins mcu, 114 gpio #if STM32F4X_PIN_NUM >= 144 // 144 pins mcu, 114 gpio
#if STM32F4X_PIN_NUM >= 176
{PH_5, I2C2, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_I2C2)},
{PH_8, I2C3, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_I2C3)},
#else
{PF_0, I2C2, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_I2C2)}, {PF_0, I2C2, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_I2C2)},
#endif #endif
#endif
{NC, NP, 0} {NC, NP, 0}
}; };
#endif #endif
@ -104,8 +109,14 @@ const PinMap PinMap_I2C_SCL[] = {
{PB_8, I2C1, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_I2C1)}, {PB_8, I2C1, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_I2C1)},
{PB_10, I2C2, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_I2C2)}, {PB_10, I2C2, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_I2C2)},
#if STM32F4X_PIN_NUM >= 144 // 144 pins mcu, 114 gpio #if STM32F4X_PIN_NUM >= 144 // 144 pins mcu, 114 gpio
#if STM32F4X_PIN_NUM >= 176
//{PF_1, I2C2, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_I2C2)},
{PH_4, I2C2, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_I2C2)},
{PH_7, I2C3, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_I2C3)},
#else
{PF_1, I2C2, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_I2C2)}, {PF_1, I2C2, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_I2C2)},
#endif #endif
#endif
{NC, NP, 0} {NC, NP, 0}
}; };
#endif #endif
@ -141,8 +152,10 @@ const PinMap PinMap_PWM[] = {
*/ */
//{PA_0, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 1, 0)}, // TIM2_CH1 //{PA_0, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 1, 0)}, // TIM2_CH1
//{PA_0, TIM5, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM5, 1, 0)}, // TIM5_CH1 //{PA_0, TIM5, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM5, 1, 0)}, // TIM5_CH1
//{PA_1, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 2, 0)}, // TIM2_CH2 {PA_1, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 2, 0)}, // TIM2_CH2 is bltouch analog?
//{PA_2, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 3, 0)}, // TIM2_CH3 {PA_2, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 3, 0)}, // TIM2_CH3 is bltouch analog?
//{PA_1, TIM5, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM5, 2, 0)}, // TIM5_CH2
//{PA_2, TIM5, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM5, 3, 0)}, // TIM5_CH3
//{PA_2, TIM9, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM9, 1, 0)}, // TIM9_CH1 //{PA_2, TIM9, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM9, 1, 0)}, // TIM9_CH1
//{PA_3, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 4, 0)}, // TIM2_CH4 //{PA_3, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 4, 0)}, // TIM2_CH4
//{PA_3, TIM5, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM5, 4, 0)}, // TIM5_CH4 //{PA_3, TIM5, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM5, 4, 0)}, // TIM5_CH4
@ -173,7 +186,7 @@ const PinMap PinMap_PWM[] = {
//{PB_9, TIM4, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM4, 4, 0)}, // TIM4_CH4 //{PB_9, TIM4, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM4, 4, 0)}, // TIM4_CH4
//{PB_9, TIM11, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM11, 1, 0)}, // TIM11_CH1 //{PB_9, TIM11, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM11, 1, 0)}, // TIM11_CH1
//{PB_10, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 3, 0)}, // TIM2_CH3 //{PB_10, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 3, 0)}, // TIM2_CH3
//{PB_11, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 4, 0)}, // TIM2_CH4 {PB_11, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 4, 0)}, // TIM2_CH4
//{PB_13, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 1, 1)}, // TIM1_CH1N //{PB_13, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 1, 1)}, // TIM1_CH1N
//{PB_14, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 2, 1)}, // TIM1_CH2N //{PB_14, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 2, 1)}, // TIM1_CH2N
//{PB_14, TIM8, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM8, 2, 1)}, // TIM8_CH2N //{PB_14, TIM8, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM8, 2, 1)}, // TIM8_CH2N
@ -186,21 +199,28 @@ const PinMap PinMap_PWM[] = {
//{PC_7, TIM8, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM8, 2, 0)}, // TIM8_CH2 //{PC_7, TIM8, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM8, 2, 0)}, // TIM8_CH2
//{PC_8, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 3, 0)}, // TIM3_CH3 //{PC_8, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 3, 0)}, // TIM3_CH3
//{PC_9, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 4, 0)}, // TIM3_CH4 //{PC_9, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 4, 0)}, // TIM3_CH4
//{PD_13, TIM4, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM4, 2, 0)}, // TIM4_CH2 {PD_13, TIM4, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM4, 2, 0)}, // TIM4_CH2
//{PD_15, TIM4, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM4, 4, 0)}, // TIM4_CH4 {PD_15, TIM4, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM4, 4, 0)}, // TIM4_CH4
//{PE_8, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 1, 1)}, // TIM1_CH1N //{PE_8, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 1, 1)}, // TIM1_CH1N
//{PE_9, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 1, 0)}, // TIM1_CH1 {PE_9, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 1, 0)}, // TIM1_CH1
//{PE_10, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 2, 1)}, // TIM1_CH2N //{PE_10, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 2, 1)}, // TIM1_CH2N
//{PE_11, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 2, 0)}, // TIM1_CH2 {PE_11, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 2, 0)}, // TIM1_CH2
//{PE_12, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 3, 1)}, // TIM1_CH3N //{PE_12, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 3, 1)}, // TIM1_CH3N
//{PE_13, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 3, 0)}, // TIM1_CH3 {PE_13, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 3, 0)}, // TIM1_CH3
//{PE_14, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 4, 0)}, // TIM1_CH4 {PE_14, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 4, 0)}, // TIM1_CH4
#if STM32F4X_PIN_NUM >= 144 //144 pins mcu, 114 gpio #if STM32F4X_PIN_NUM >= 144 //144 pins mcu, 114 gpio
//{PF_6, TIM10, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM10, 1, 0)}, // TIM10_CH1 //{PF_6, TIM10, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM10, 1, 0)}, // TIM10_CH1
//{PF_7, TIM11, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM11, 1, 0)}, // TIM11_CH1 //{PF_7, TIM11, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM11, 1, 0)}, // TIM11_CH1
//{PF_8, TIM13, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF9_TIM13, 1, 0)}, // TIM13_CH1 //{PF_8, TIM13, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF9_TIM13, 1, 0)}, // TIM13_CH1
//{PF_9, TIM14, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF9_TIM14, 1, 0)}, // TIM14_CH1 //{PF_9, TIM14, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF9_TIM14, 1, 0)}, // TIM14_CH1
#endif #endif
#if STM32F4X_PIN_NUM >= 176 //176 pins mcu, 140 gpio
{PH_10, TIM5, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM5, 1, 0)}, // TIM5_CH1
{PH_6, TIM12, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF9_TIM12, 1, 0)}, // TIM12_CH1
//{PH_11, TIM5, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM5, 2, 0)}, // TIM5_CH2
{PI_5, TIM8, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM8, 1, 0)}, // TIM8_CH1
{PI_6, TIM8, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM8, 2, 0)}, // TIM8_CH2
#endif
{NC, NP, 0} {NC, NP, 0}
}; };
#endif #endif
@ -275,7 +295,8 @@ const PinMap PinMap_UART_CTS[] = {
#ifdef HAL_SPI_MODULE_ENABLED #ifdef HAL_SPI_MODULE_ENABLED
const PinMap PinMap_SPI_MOSI[] = { const PinMap PinMap_SPI_MOSI[] = {
{PB_5, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF5_SPI1)}, //{PB_5, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF5_SPI1)},
{PA_7, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF5_SPI1)},
{PB_15, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)}, {PB_15, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)},
{PC_12, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_SPI3)}, {PC_12, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_SPI3)},
{NC, NP, 0} {NC, NP, 0}

View File

@ -586,7 +586,7 @@ lib_ignore = Adafruit NeoPixel
# #
# STM32F401VE # STM32F401VE
# 'STEVAL-3DP001)' STM32F401VE board - https://www.st.com/en/evaluation-tools/steval-3dp001v1.html # 'STEVAL-3DP001V1' STM32F401VE board - https://www.st.com/en/evaluation-tools/steval-3dp001v1.html
# #
[env:STM32F401VE_STEVAL] [env:STM32F401VE_STEVAL]
platform = ststm32 platform = ststm32
@ -677,6 +677,37 @@ src_filter = ${common.default_src_filter} +<src/HAL/HAL_STM32>
debug_tool = stlink debug_tool = stlink
debug_init_break = debug_init_break =
#
# Bigtreetech GTR V1.0 (STM32F407IGT6 ARM Cortex-M4)
#
[env:BIGTREE_GTR_V1_0]
platform = ststm32@>=5.7.0
framework = arduino
platform_packages = framework-arduinoststm32@>=3.10700.191028
board = BigTree_SKR_Pro
extra_scripts = pre:buildroot/share/PlatformIO/scripts/generic_create_variant.py
build_flags = ${common.build_flags}
-DUSBCON -DUSBD_USE_CDC -DUSBD_VID=0x0483 -DUSB_PRODUCT=\"STM32F407IG\"
-DTARGET_STM32F4 -DSTM32F407IX -DVECT_TAB_OFFSET=0x8000
-DHAVE_HWSERIAL3
-DHAVE_HWSERIAL6
-DPIN_SERIAL3_RX=PD_9
-DPIN_SERIAL3_TX=PD_8
-DPIN_SERIAL6_RX=PC_7
-DPIN_SERIAL6_TX=PC_6
-IMarlin/src/HAL/HAL_STM32
lib_deps =
U8glib-HAL=https://github.com/MarlinFirmware/U8glib-HAL/archive/bugfix.zip
LiquidCrystal
TMCStepper@>=0.5.2,<1.0.0
Adafruit NeoPixel
LiquidTWI2=https://github.com/lincomatic/LiquidTWI2/archive/master.zip
Arduino-L6470=https://github.com/ameyer/Arduino-L6470/archive/dev.zip
lib_ignore = SoftwareSerial, SoftwareSerialM
src_filter = ${common.default_src_filter} +<src/HAL/HAL_STM32>
monitor_speed = 250000
# #
# BigTreeTech BTT002 (STM32F407VET6 ARM Cortex-M4) # BigTreeTech BTT002 (STM32F407VET6 ARM Cortex-M4)
# #