Marlin_Firmware/Marlin/src/inc/Conditionals_LCD.h

/**
 * Marlin 3D Printer Firmware
 * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
 *
 * Based on Sprinter and grbl.
 * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
 *
 * This program is free software: you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation, either version 3 of the License, or
 * (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program.  If not, see <https://www.gnu.org/licenses/>.
 *
 */
#pragma once

/**
 * Conditionals_LCD.h
 * Conditionals that need to be set before Configuration_adv.h or pins.h
 */

// Kinematics
#if ENABLED(MORGAN_SCARA)
  #define IS_SCARA 1
  #define IS_KINEMATIC 1
#elif ENABLED(DELTA)
  #define IS_KINEMATIC 1
#else
  #define IS_CARTESIAN 1
#endif

// MKS_LCD12864 is a variant of MKS_MINI_12864
#if ENABLED(MKS_LCD12864)
  #define MKS_MINI_12864
#endif

/**
 * General Flags that may be set below by specific LCDs
 *
 *  DOGLCD                : Run a Graphical LCD through U8GLib (with MarlinUI)
 *  IS_ULTIPANEL          : Define LCD_PINS_D5/6/7 for direct-connected "Ultipanel" LCDs
 *  IS_ULTRA_LCD          : Ultra LCD, not necessarily Ultipanel. Used most often with NEWPANEL.
 *  IS_RRD_SC             : Common RRD Smart Controller digital interface pins
 *  IS_RRD_FG_SC          : Common RRD Full Graphical Smart Controller digital interface pins
 *  U8GLIB_ST7920         : Most common DOGM display SPI interface, supporting a "lightweight" display mode.
 *  U8GLIB_SH1106         : SH1106 OLED with I2C interface via U8GLib
 *  IS_U8GLIB_SSD1306     : SSD1306 OLED with I2C interface via U8GLib
 *  U8GLIB_SSD1309        : SSD1309 OLED with I2C interface via U8GLib
 *  U8GLIB_ST7565_64128N  : ST7565 128x64 LCD with SPI interface via U8GLib
 *  U8GLIB_LM6059_AF      : LM6059 with Hardware SPI via U8GLib
 */
#if EITHER(MKS_MINI_12864, ENDER2_STOCKDISPLAY)

  #define MINIPANEL

#elif ENABLED(CARTESIO_UI)

  #define DOGLCD
  #define IS_ULTIPANEL

#elif EITHER(DWIN_MARLINUI_PORTRAIT, DWIN_MARLINUI_LANDSCAPE)

  #define IS_DWIN_MARLINUI 1
  #define IS_ULTIPANEL

#elif ENABLED(ZONESTAR_LCD)

  #define ADC_KEYPAD
  #define IS_RRW_KEYPAD
  #define REPRAPWORLD_KEYPAD_MOVE_STEP 10.0
  #define ADC_KEY_NUM 8
  #define IS_ULTIPANEL

  // This helps to implement ADC_KEYPAD menus
  #define REVERSE_MENU_DIRECTION
  #define ENCODER_PULSES_PER_STEP 1
  #define ENCODER_STEPS_PER_MENU_ITEM 1
  #define ENCODER_FEEDRATE_DEADZONE 2

#elif ENABLED(ZONESTAR_12864LCD)
  #define DOGLCD
  #define IS_RRD_SC
  #define U8GLIB_ST7920

#elif ENABLED(ZONESTAR_12864OLED)
  #define IS_RRD_SC
  #define U8GLIB_SH1106

#elif ENABLED(ZONESTAR_12864OLED_SSD1306)
  #define IS_RRD_SC
  #define IS_U8GLIB_SSD1306

#elif ENABLED(RADDS_DISPLAY)
  #define IS_ULTIPANEL
  #define ENCODER_PULSES_PER_STEP 2

#elif EITHER(ANET_FULL_GRAPHICS_LCD, BQ_LCD_SMART_CONTROLLER)

  #define IS_RRD_FG_SC

#elif ANY(miniVIKI, VIKI2, ELB_FULL_GRAPHIC_CONTROLLER, AZSMZ_12864)

  #define DOGLCD
  #define IS_ULTIPANEL

  #if ENABLED(miniVIKI)
    #define U8GLIB_ST7565_64128N
  #elif ENABLED(VIKI2)
    #define U8GLIB_ST7565_64128N
  #elif ENABLED(ELB_FULL_GRAPHIC_CONTROLLER)
    #define U8GLIB_LM6059_AF
  #elif ENABLED(AZSMZ_12864)
    #define U8GLIB_ST7565_64128N
  #endif

#elif ENABLED(OLED_PANEL_TINYBOY2)

  #define IS_U8GLIB_SSD1306
  #define IS_ULTIPANEL

#elif ENABLED(RA_CONTROL_PANEL)

  #define LCD_I2C_TYPE_PCA8574
  #define LCD_I2C_ADDRESS 0x27   // I2C Address of the port expander
  #define IS_ULTIPANEL

#elif ENABLED(REPRAPWORLD_GRAPHICAL_LCD)

  #define DOGLCD
  #define U8GLIB_ST7920
  #define IS_ULTIPANEL

#elif ENABLED(CR10_STOCKDISPLAY)

  #define IS_RRD_FG_SC
  #define BOARD_ST7920_DELAY_1 DELAY_NS(125)
  #define BOARD_ST7920_DELAY_2 DELAY_NS(125)
  #define BOARD_ST7920_DELAY_3 DELAY_NS(125)

#elif ENABLED(MKS_12864OLED)

  #define IS_RRD_SC
  #define U8GLIB_SH1106

#elif ENABLED(MKS_12864OLED_SSD1306)

  #define IS_RRD_SC
  #define IS_U8GLIB_SSD1306

#elif ENABLED(FYSETC_242_OLED_12864)

  #define IS_RRD_SC
  #define U8GLIB_SH1106

  #define LED_CONTROL_MENU
  #define NEOPIXEL_LED
  #undef NEOPIXEL_TYPE
  #define NEOPIXEL_TYPE       NEO_RGB
  #if NEOPIXEL_PIXELS < 3
    #undef NEOPIXELS_PIXELS
    #define NEOPIXEL_PIXELS     3
  #endif
  #ifndef NEOPIXEL_BRIGHTNESS
    #define NEOPIXEL_BRIGHTNESS 127
  #endif

  #if ENABLED(PSU_CONTROL)
    #define LED_BACKLIGHT_TIMEOUT 10000
  #endif

#elif ANY(FYSETC_MINI_12864_X_X, FYSETC_MINI_12864_1_2, FYSETC_MINI_12864_2_0, FYSETC_MINI_12864_2_1, FYSETC_GENERIC_12864_1_1)

  #define FYSETC_MINI_12864
  #define DOGLCD
  #define IS_ULTIPANEL
  #define LED_COLORS_REDUCE_GREEN
  #if ENABLED(PSU_CONTROL) && EITHER(FYSETC_MINI_12864_2_0, FYSETC_MINI_12864_2_1)
    #define LED_BACKLIGHT_TIMEOUT 10000
  #endif

  // Require LED backlighting enabled
  #if EITHER(FYSETC_MINI_12864_1_2, FYSETC_MINI_12864_2_0)
    #define RGB_LED
  #elif ENABLED(FYSETC_MINI_12864_2_1)
    #define LED_CONTROL_MENU
    #define NEOPIXEL_LED
    #undef NEOPIXEL_TYPE
    #define NEOPIXEL_TYPE       NEO_RGB
    #if NEOPIXEL_PIXELS < 3
      #undef NEOPIXELS_PIXELS
      #define NEOPIXEL_PIXELS     3
    #endif
    #ifndef NEOPIXEL_BRIGHTNESS
      #define NEOPIXEL_BRIGHTNESS 127
    #endif
    //#define NEOPIXEL_STARTUP_TEST
  #endif

#elif ENABLED(ULTI_CONTROLLER)

  #define IS_ULTIPANEL
  #define U8GLIB_SSD1309
  #define LCD_RESET_PIN LCD_PINS_D6 //  This controller need a reset pin
  #define ENCODER_PULSES_PER_STEP 2
  #define ENCODER_STEPS_PER_MENU_ITEM 2

#elif ENABLED(MAKEBOARD_MINI_2_LINE_DISPLAY_1602)

  #define IS_RRD_SC
  #define LCD_WIDTH 16
  #define LCD_HEIGHT 2

#elif EITHER(TFTGLCD_PANEL_SPI, TFTGLCD_PANEL_I2C)

  #define IS_TFTGLCD_PANEL 1
  #define IS_ULTIPANEL                      // Note that IS_ULTIPANEL leads to HAS_WIRED_LCD

  #if ENABLED(SDSUPPORT) && DISABLED(LCD_PROGRESS_BAR)
    #define LCD_PROGRESS_BAR
  #endif
  #if ENABLED(TFTGLCD_PANEL_I2C)
    #define LCD_USE_I2C_BUZZER              // Enable buzzer on LCD for I2C and SPI buses (LiquidTWI2 not required)
    #define LCD_I2C_ADDRESS           0x27  // Must be equal to panel's I2C slave addres
  #endif
  #define STD_ENCODER_PULSES_PER_STEP 2
  #define STD_ENCODER_STEPS_PER_MENU_ITEM 1
  #define LCD_WIDTH                   20    // 20 or 24 chars in line
  #define LCD_HEIGHT                  10    // Character lines
  #define LCD_CONTRAST_MIN            127
  #define LCD_CONTRAST_MAX            255
  #define DEFAULT_LCD_CONTRAST        250
  #define CONVERT_TO_EXT_ASCII        // Use extended 128-255 symbols from ASCII table.
                                      // At this time present conversion only for cyrillic - bg, ru and uk languages.
                                      // First 7 ASCII symbols in panel font must be replaced with Marlin's special symbols.
#endif

#if ENABLED(IS_RRD_FG_SC)
  #define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
#endif

#if EITHER(MAKRPANEL, MINIPANEL)
  #define IS_ULTIPANEL
  #define DOGLCD
  #if ENABLED(MAKRPANEL)
    #define U8GLIB_ST7565_64128N
  #endif
#endif

#if ENABLED(IS_U8GLIB_SSD1306)
  #define U8GLIB_SSD1306
#endif

#if ENABLED(OVERLORD_OLED)
  #define IS_ULTIPANEL
  #define U8GLIB_SH1106
  /**
   * PCA9632 for buzzer and LEDs via i2c
   * No auto-inc, red and green leds switched, buzzer
   */
  #define PCA9632
  #define PCA9632_NO_AUTO_INC
  #define PCA9632_GRN         0x00
  #define PCA9632_RED         0x02
  #define PCA9632_BUZZER
  #define PCA9632_BUZZER_DATA { 0x09, 0x02 }

  #define ENCODER_PULSES_PER_STEP     1 // Overlord uses buttons
  #define ENCODER_STEPS_PER_MENU_ITEM 1
#endif

// 128x64 I2C OLED LCDs - SSD1306/SSD1309/SH1106
#if ANY(U8GLIB_SSD1306, U8GLIB_SSD1309, U8GLIB_SH1106)
  #define HAS_U8GLIB_I2C_OLED 1
#endif
#if HAS_U8GLIB_I2C_OLED
  #define IS_ULTRA_LCD
  #define DOGLCD
#endif

// ST7920-based graphical displays
#if ANY(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER, LCD_FOR_MELZI, SILVER_GATE_GLCD_CONTROLLER)
  #define DOGLCD
  #define U8GLIB_ST7920
  #define IS_RRD_SC
#endif

// RepRapDiscount LCD or Graphical LCD with rotary click encoder
#if ENABLED(IS_RRD_SC)
  #define REPRAP_DISCOUNT_SMART_CONTROLLER
#endif

/**
 * SPI Ultipanels
 */

// Basic Ultipanel-like displays
#if ANY(ULTIMAKERCONTROLLER, REPRAP_DISCOUNT_SMART_CONTROLLER, G3D_PANEL, RIGIDBOT_PANEL, PANEL_ONE, U8GLIB_SH1106)
  #define IS_ULTIPANEL
#endif

// Einstart OLED has Cardinal nav via pins defined in pins_EINSTART-S.h
#if ENABLED(U8GLIB_SH1106_EINSTART)
  #define DOGLCD
  #define IS_ULTIPANEL
#endif

// FSMC/SPI TFT Panels (LVGL)
#if EITHER(TFT_LVGL_UI_SPI, TFT_LVGL_UI_FSMC)
  #define HAS_TFT_LVGL_UI 1
#endif

// FSMC/SPI TFT Panels
#if EITHER(FSMC_GRAPHICAL_TFT, SPI_GRAPHICAL_TFT)
  #define TFT_SCALED_DOGLCD 1
#endif

#if TFT_SCALED_DOGLCD
  #define DOGLCD
  #define IS_ULTIPANEL
  #define DELAYED_BACKLIGHT_INIT
#elif ENABLED(TFT_LVGL_UI_SPI)
  #define DELAYED_BACKLIGHT_INIT
#endif

// FSMC/SPI TFT Panels using standard HAL/tft/tft_(fsmc|spi).h
#if ANY(TFT_320x240, TFT_480x320, TFT_LVGL_UI_FSMC, FSMC_GRAPHICAL_TFT)
  #define HAS_FSMC_TFT 1
#elif ANY(TFT_320x240_SPI, TFT_480x320_SPI, TFT_LVGL_UI_SPI, SPI_GRAPHICAL_TFT)
  #define HAS_SPI_TFT 1
#endif

// Color UI
#if ANY(TFT_320x240, TFT_480x320, TFT_320x240_SPI, TFT_480x320_SPI)
  #define HAS_GRAPHICAL_TFT 1
  #define IS_ULTIPANEL
#endif

// Fewer lines with touch buttons on-screen
#if EITHER(TFT_320x240, TFT_320x240_SPI)
  #define HAS_UI_320x240 1
  #define LCD_HEIGHT TERN(TOUCH_SCREEN, 6, 7)
#elif EITHER(TFT_480x320, TFT_480x320_SPI)
  #define HAS_UI_480x320 1
  #define LCD_HEIGHT TERN(TOUCH_SCREEN, 6, 7)
#endif

/**
 * I2C Panels
 */

#if EITHER(LCD_SAINSMART_I2C_1602, LCD_SAINSMART_I2C_2004)

  #define LCD_I2C_TYPE_PCF8575
  #define LCD_I2C_ADDRESS 0x27   // I2C Address of the port expander

  #if ENABLED(LCD_SAINSMART_I2C_2004)
    #define LCD_WIDTH 20
    #define LCD_HEIGHT 4
  #endif

#elif ENABLED(LCD_I2C_PANELOLU2)

  // PANELOLU2 LCD with status LEDs, separate encoder and click inputs

  #define LCD_I2C_TYPE_MCP23017
  #define LCD_I2C_ADDRESS 0x20 // I2C Address of the port expander
  #define LCD_USE_I2C_BUZZER   // Enable buzzer on LCD (optional)
  #define IS_ULTIPANEL

#elif ENABLED(LCD_I2C_VIKI)

  /**
   * Panucatt VIKI LCD with status LEDs, integrated click & L/R/U/P buttons, separate encoder inputs
   *
   * This uses the LiquidTWI2 library v1.2.3 or later ( https://github.com/lincomatic/LiquidTWI2 )
   * Make sure the LiquidTWI2 directory is placed in the Arduino or Sketchbook libraries subdirectory.
   * Note: The pause/stop/resume LCD button pin should be connected to the Arduino
   *       BTN_ENC pin (or set BTN_ENC to -1 if not used)
   */
  #define LCD_I2C_TYPE_MCP23017
  #define LCD_I2C_ADDRESS 0x20 // I2C Address of the port expander
  #define LCD_USE_I2C_BUZZER   // Enable buzzer on LCD (requires LiquidTWI2 v1.2.3 or later)
  #define IS_ULTIPANEL

  #define ENCODER_FEEDRATE_DEADZONE 4

  #define STD_ENCODER_PULSES_PER_STEP 1
  #define STD_ENCODER_STEPS_PER_MENU_ITEM 2

#elif ENABLED(G3D_PANEL)

  #define STD_ENCODER_PULSES_PER_STEP 2
  #define STD_ENCODER_STEPS_PER_MENU_ITEM 1

#elif ANY(REPRAP_DISCOUNT_SMART_CONTROLLER, miniVIKI, VIKI2, ELB_FULL_GRAPHIC_CONTROLLER, AZSMZ_12864, OLED_PANEL_TINYBOY2, BQ_LCD_SMART_CONTROLLER, LCD_I2C_PANELOLU2)

  #define STD_ENCODER_PULSES_PER_STEP 4
  #define STD_ENCODER_STEPS_PER_MENU_ITEM 1

#endif

#ifndef STD_ENCODER_PULSES_PER_STEP
  #if ENABLED(TOUCH_SCREEN)
    #define STD_ENCODER_PULSES_PER_STEP 2
  #else
    #define STD_ENCODER_PULSES_PER_STEP 5
  #endif
#endif
#ifndef STD_ENCODER_STEPS_PER_MENU_ITEM
  #define STD_ENCODER_STEPS_PER_MENU_ITEM 1
#endif
#ifndef ENCODER_PULSES_PER_STEP
  #define ENCODER_PULSES_PER_STEP STD_ENCODER_PULSES_PER_STEP
#endif
#ifndef ENCODER_STEPS_PER_MENU_ITEM
  #define ENCODER_STEPS_PER_MENU_ITEM STD_ENCODER_STEPS_PER_MENU_ITEM
#endif
#ifndef ENCODER_FEEDRATE_DEADZONE
  #define ENCODER_FEEDRATE_DEADZONE 6
#endif

// Shift register panels
// ---------------------
// 2 wire Non-latching LCD SR from:
// https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/schematics#!shiftregister-connection
#if ENABLED(FF_INTERFACEBOARD)
  #define SR_LCD_3W_NL    // Non latching 3 wire shift register
  #define IS_ULTIPANEL
#elif ENABLED(SAV_3DLCD)
  #define SR_LCD_2W_NL    // Non latching 2 wire shift register
  #define IS_ULTIPANEL
#endif

#if ENABLED(IS_ULTIPANEL)
  #define ULTIPANEL
#endif
#if ENABLED(ULTIPANEL)
  #define IS_ULTRA_LCD
  #define NEWPANEL
#endif
#if ENABLED(IS_ULTRA_LCD)
  #define ULTRA_LCD
#endif

#if ENABLED(IS_RRW_KEYPAD)
  #define REPRAPWORLD_KEYPAD
#endif

// Keypad needs a move step
#if ENABLED(REPRAPWORLD_KEYPAD)
  #define NEWPANEL
  #ifndef REPRAPWORLD_KEYPAD_MOVE_STEP
    #define REPRAPWORLD_KEYPAD_MOVE_STEP 1.0
  #endif
#endif

// Aliases for LCD features
#if ANY(DGUS_LCD_UI_ORIGIN, DGUS_LCD_UI_FYSETC, DGUS_LCD_UI_HIPRECY)
  #define HAS_DGUS_LCD 1
#endif

// Extensible UI serial touch screens. (See src/lcd/extui)
#if ANY(HAS_DGUS_LCD, MALYAN_LCD, TOUCH_UI_FTDI_EVE, ANYCUBIC_LCD_I3MEGA, ANYCUBIC_LCD_CHIRON)
  #define IS_EXTUI
  #define EXTENSIBLE_UI
#endif

// Aliases for LCD features
#if EITHER(ULTRA_LCD, EXTENSIBLE_UI)
  #define HAS_DISPLAY 1
#endif

#if ENABLED(ULTRA_LCD)
  #define HAS_WIRED_LCD 1
  #if ENABLED(DOGLCD)
    #define HAS_MARLINUI_U8GLIB 1
  #elif IS_TFTGLCD_PANEL
    // Neither DOGM nor HD44780. Fully customized interface.
  #elif DISABLED(HAS_GRAPHICAL_TFT)
    #define HAS_MARLINUI_HD44780 1
  #endif
#endif

#if ENABLED(ULTIPANEL) && DISABLED(NO_LCD_MENUS)
  #define HAS_LCD_MENU 1
#endif
#if ENABLED(ADC_KEYPAD)
  #define HAS_ADC_BUTTONS 1
#endif

#if HAS_MARLINUI_U8GLIB
  #ifndef LCD_PIXEL_WIDTH
    #define LCD_PIXEL_WIDTH 128
  #endif
  #ifndef LCD_PIXEL_HEIGHT
    #define LCD_PIXEL_HEIGHT 64
  #endif
#endif

/**
 * Extruders have some combination of stepper motors and hotends
 * so we separate these concepts into the defines:
 *
 *  EXTRUDERS    - Number of Selectable Tools
 *  HOTENDS      - Number of hotends, whether connected or separate
 *  E_STEPPERS   - Number of actual E stepper motors
 *  E_MANUAL     - Number of E steppers for LCD move options
 */

#if EXTRUDERS == 0
  #undef EXTRUDERS
  #define EXTRUDERS 0
  #undef SINGLENOZZLE
  #undef SWITCHING_EXTRUDER
  #undef SWITCHING_NOZZLE
  #undef MIXING_EXTRUDER
  #undef MK2_MULTIPLEXER
  #undef PRUSA_MMU2
  #undef HOTEND_IDLE_TIMEOUT
#elif EXTRUDERS > 1
  #define HAS_MULTI_EXTRUDER 1
#endif

#if ENABLED(SWITCHING_EXTRUDER)   // One stepper for every two EXTRUDERS
  #if EXTRUDERS > 4
    #define E_STEPPERS    3
  #elif EXTRUDERS > 2
    #define E_STEPPERS    2
  #else
    #define E_STEPPERS    1
  #endif
  #if DISABLED(SWITCHING_NOZZLE)
    #define HOTENDS       E_STEPPERS
  #endif
#elif ENABLED(MIXING_EXTRUDER)
  #define E_STEPPERS      MIXING_STEPPERS
  #define E_MANUAL        1
  #if MIXING_STEPPERS == 2
    #define HAS_DUAL_MIXING 1
  #endif
#elif ENABLED(SWITCHING_TOOLHEAD)
  #define E_STEPPERS      EXTRUDERS
  #define E_MANUAL        EXTRUDERS
#elif ENABLED(PRUSA_MMU2)
  #define E_STEPPERS 1
#endif

// No inactive extruders with MK2_MULTIPLEXER or SWITCHING_NOZZLE
#if EITHER(MK2_MULTIPLEXER, SWITCHING_NOZZLE)
  #undef DISABLE_INACTIVE_EXTRUDER
#endif

// Průša MK2 Multiplexer and MMU 2.0 force SINGLENOZZLE
#if EITHER(MK2_MULTIPLEXER, PRUSA_MMU2)
  #define SINGLENOZZLE
#endif

#if EITHER(SINGLENOZZLE, MIXING_EXTRUDER)         // One hotend, one thermistor, no XY offset
  #undef HOTENDS
  #define HOTENDS       1
  #undef HOTEND_OFFSET_X
  #undef HOTEND_OFFSET_Y
#endif

#ifndef HOTENDS
  #define HOTENDS EXTRUDERS
#endif
#ifndef E_STEPPERS
  #define E_STEPPERS EXTRUDERS
#endif
#ifndef E_MANUAL
  #define E_MANUAL EXTRUDERS
#endif

#if HOTENDS
  #define HAS_HOTEND 1
  #ifndef HOTEND_OVERSHOOT
    #define HOTEND_OVERSHOOT 15
  #endif
  #if HOTENDS > 1
    #define HAS_MULTI_HOTEND 1
    #define HAS_HOTEND_OFFSET 1
  #endif
#else
  #undef PID_PARAMS_PER_HOTEND
#endif

// Helper macros for extruder and hotend arrays
#define HOTEND_LOOP() for (int8_t e = 0; e < HOTENDS; e++)
#define ARRAY_BY_EXTRUDERS(V...) ARRAY_N(EXTRUDERS, V)
#define ARRAY_BY_EXTRUDERS1(v1) ARRAY_BY_EXTRUDERS(v1, v1, v1, v1, v1, v1, v1, v1)
#define ARRAY_BY_HOTENDS(V...) ARRAY_N(HOTENDS, V)
#define ARRAY_BY_HOTENDS1(v1) ARRAY_BY_HOTENDS(v1, v1, v1, v1, v1, v1, v1, v1)

#if ENABLED(SWITCHING_EXTRUDER) && (DISABLED(SWITCHING_NOZZLE) || SWITCHING_EXTRUDER_SERVO_NR != SWITCHING_NOZZLE_SERVO_NR)
  #define DO_SWITCH_EXTRUDER 1
#endif

/**
 * Default hotend offsets, if not defined
 */
#if HAS_HOTEND_OFFSET
  #ifndef HOTEND_OFFSET_X
    #define HOTEND_OFFSET_X { 0 } // X offsets for each extruder
  #endif
  #ifndef HOTEND_OFFSET_Y
    #define HOTEND_OFFSET_Y { 0 } // Y offsets for each extruder
  #endif
  #ifndef HOTEND_OFFSET_Z
    #define HOTEND_OFFSET_Z { 0 } // Z offsets for each extruder
  #endif
#endif

/**
 * DISTINCT_E_FACTORS affects how some E factors are accessed
 */
#if ENABLED(DISTINCT_E_FACTORS) && E_STEPPERS > 1
  #define DISTINCT_E E_STEPPERS
  #define XYZE_N (XYZ + E_STEPPERS)
  #define E_INDEX_N(E) (E)
  #define E_AXIS_N(E) AxisEnum(E_AXIS + E)
  #define UNUSED_E(E) NOOP
#else
  #undef DISTINCT_E_FACTORS
  #define DISTINCT_E 1
  #define XYZE_N XYZE
  #define E_INDEX_N(E) 0
  #define E_AXIS_N(E) E_AXIS
  #define UNUSED_E(E) UNUSED(E)
#endif

#if ENABLED(DWIN_CREALITY_LCD)
  #define SERIAL_CATCHALL 0
#endif

// Pressure sensor with a BLTouch-like interface
#if ENABLED(CREALITY_TOUCH)
  #define BLTOUCH
#endif

/**
 * The BLTouch Probe emulates a servo probe
 * and uses "special" angles for its state.
 */
#if ENABLED(BLTOUCH)
  #ifndef Z_PROBE_SERVO_NR
    #define Z_PROBE_SERVO_NR 0
  #endif
  #undef DEACTIVATE_SERVOS_AFTER_MOVE

  // Always disable probe pin inverting for BLTouch
  #undef Z_MIN_PROBE_ENDSTOP_INVERTING
  #define Z_MIN_PROBE_ENDSTOP_INVERTING false
  #if ENABLED(Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN)
    #undef Z_MIN_ENDSTOP_INVERTING
    #define Z_MIN_ENDSTOP_INVERTING false
  #endif
#endif

/**
 * Set a flag for a servo probe (or BLTouch)
 */
#ifdef Z_PROBE_SERVO_NR
  #define HAS_Z_SERVO_PROBE 1
#endif
#if ANY(HAS_Z_SERVO_PROBE, SWITCHING_EXTRUDER, SWITCHING_NOZZLE)
  #define HAS_SERVO_ANGLES 1
#endif
#if !HAS_SERVO_ANGLES
  #undef EDITABLE_SERVO_ANGLES
#endif

/**
 * Set flags for enabled probes
 */
#if ANY(HAS_Z_SERVO_PROBE, FIX_MOUNTED_PROBE, NOZZLE_AS_PROBE, TOUCH_MI_PROBE, Z_PROBE_ALLEN_KEY, Z_PROBE_SLED, SOLENOID_PROBE, SENSORLESS_PROBING, RACK_AND_PINION_PROBE)
  #define HAS_BED_PROBE 1
#endif

#if ANY(HAS_BED_PROBE, PROBE_MANUALLY, MESH_BED_LEVELING)
  #define PROBE_SELECTED 1
#endif

#if HAS_BED_PROBE
  #if DISABLED(NOZZLE_AS_PROBE)
    #define HAS_PROBE_XY_OFFSET 1
  #endif
  #if DISABLED(Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN)
    #define HAS_CUSTOM_PROBE_PIN 1
  #endif
  #if Z_HOME_DIR < 0 && (!HAS_CUSTOM_PROBE_PIN || ENABLED(USE_PROBE_FOR_Z_HOMING))
    #define HOMING_Z_WITH_PROBE 1
  #endif
  #ifndef Z_PROBE_LOW_POINT
    #define Z_PROBE_LOW_POINT -5
  #endif
  #if ENABLED(Z_PROBE_ALLEN_KEY)
    #define PROBE_TRIGGERED_WHEN_STOWED_TEST 1 // Extra test for Allen Key Probe
  #endif
  #if MULTIPLE_PROBING > 1
    #if EXTRA_PROBING > 0
      #define TOTAL_PROBING (MULTIPLE_PROBING + EXTRA_PROBING)
    #else
      #define TOTAL_PROBING MULTIPLE_PROBING
    #endif
  #endif
#else
  // Clear probe pin settings when no probe is selected
  #undef Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
#endif

/**
 * Set granular options based on the specific type of leveling
 */
#if ENABLED(AUTO_BED_LEVELING_UBL)
  #undef LCD_BED_LEVELING
  #if ENABLED(DELTA)
    #define UBL_SEGMENTED 1
  #endif
#endif
#if EITHER(AUTO_BED_LEVELING_LINEAR, AUTO_BED_LEVELING_3POINT)
  #define ABL_PLANAR 1
#endif
#if EITHER(AUTO_BED_LEVELING_LINEAR, AUTO_BED_LEVELING_BILINEAR)
  #define ABL_GRID 1
#endif
#if ANY(AUTO_BED_LEVELING_LINEAR, AUTO_BED_LEVELING_BILINEAR, AUTO_BED_LEVELING_3POINT)
  #define HAS_ABL_NOT_UBL 1
#endif
#if ANY(AUTO_BED_LEVELING_BILINEAR, AUTO_BED_LEVELING_UBL, MESH_BED_LEVELING)
  #define HAS_MESH 1
#endif
#if EITHER(AUTO_BED_LEVELING_UBL, AUTO_BED_LEVELING_3POINT)
  #define NEEDS_THREE_PROBE_POINTS 1
#endif
#if EITHER(HAS_ABL_NOT_UBL, AUTO_BED_LEVELING_UBL)
  #define HAS_ABL_OR_UBL 1
  #if DISABLED(PROBE_MANUALLY)
    #define HAS_AUTOLEVEL 1
  #endif
#endif
#if EITHER(HAS_ABL_OR_UBL, MESH_BED_LEVELING)
  #define HAS_LEVELING 1
  #if DISABLED(AUTO_BED_LEVELING_UBL)
    #define PLANNER_LEVELING 1
  #endif
#endif
#if EITHER(HAS_ABL_OR_UBL, Z_MIN_PROBE_REPEATABILITY_TEST)
  #define HAS_PROBING_PROCEDURE 1
#endif
#if !HAS_LEVELING
  #undef RESTORE_LEVELING_AFTER_G28
#endif

#ifdef GRID_MAX_POINTS_X
  #define GRID_MAX_POINTS ((GRID_MAX_POINTS_X) * (GRID_MAX_POINTS_Y))
  #define GRID_LOOP(A,B) LOOP_L_N(A, GRID_MAX_POINTS_X) LOOP_L_N(B, GRID_MAX_POINTS_Y)
#endif

#ifndef INVERT_X_DIR
  #define INVERT_X_DIR false
#endif
#ifndef INVERT_Y_DIR
  #define INVERT_Y_DIR false
#endif
#ifndef INVERT_Z_DIR
  #define INVERT_Z_DIR false
#endif
#ifndef INVERT_E_DIR
  #define INVERT_E_DIR false
#endif

#if ENABLED(SLIM_LCD_MENUS)
  #define BOOT_MARLIN_LOGO_SMALL
#endif

// This flag indicates some kind of jerk storage is needed
#if EITHER(CLASSIC_JERK, IS_KINEMATIC)
  #define HAS_CLASSIC_JERK 1
#endif

#if DISABLED(CLASSIC_JERK)
  #define HAS_JUNCTION_DEVIATION 1
#endif

// E jerk exists with JD disabled (of course) but also when Linear Advance is disabled on Delta/SCARA
#if ENABLED(CLASSIC_JERK) || (IS_KINEMATIC && DISABLED(LIN_ADVANCE))
  #define HAS_CLASSIC_E_JERK 1
#endif

#ifndef SPI_SPEED
  #define SPI_SPEED SPI_FULL_SPEED
#endif

#if SERIAL_PORT == -1 || SERIAL_PORT_2 == -1
  #define HAS_USB_SERIAL 1
#endif

/**
 * This setting is also used by M109 when trying to calculate
 * a ballpark safe margin to prevent wait-forever situation.
 */
#ifndef EXTRUDE_MINTEMP
  #define EXTRUDE_MINTEMP 170
#endif