82 lines
1.8 KiB
INI
82 lines
1.8 KiB
INI
# This file contains common pin mappings for the BIGTREETECH EBBCan
|
|
# Canbus board. To use this config, the firmware should be compiled for the
|
|
# RP2040 with "USB" or "CAN bus (on gpio4/gpio5)".
|
|
# The "EBB Can" micro-controller will be used to control the components on the nozzle.
|
|
|
|
# See docs/Config_Reference.md for a description of parameters.
|
|
|
|
[mcu EBBCan]
|
|
serial: /dev/serial/by-id/usb-Klipper_Klipper_firmware_12345-if00
|
|
#canbus_uuid: 0e0d81e4210c
|
|
|
|
[temperature_sensor EBB_NTC]
|
|
sensor_type: Generic 3950
|
|
sensor_pin: EBBCan:gpio28
|
|
|
|
[adxl345]
|
|
cs_pin: EBBCan:gpio1
|
|
spi_software_sclk_pin: EBBCan:gpio2
|
|
spi_software_mosi_pin: EBBCan:gpio0
|
|
spi_software_miso_pin: EBBCan:gpio3
|
|
axes_map: z,-y,x
|
|
|
|
[resonance_tester]
|
|
probe_points: 100, 100, 20
|
|
accel_chip: adxl345
|
|
|
|
[extruder]
|
|
step_pin: EBBCan:gpio18
|
|
dir_pin: !EBBCan:gpio19
|
|
enable_pin: !EBBCan:gpio17
|
|
microsteps: 16
|
|
rotation_distance: 33.500
|
|
nozzle_diameter: 0.400
|
|
filament_diameter: 1.750
|
|
heater_pin: EBBCan:gpio7
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
sensor_pin: EBBCan:gpio27
|
|
control: pid
|
|
pid_Kp: 21.527
|
|
pid_Ki: 1.063
|
|
pid_Kd: 108.982
|
|
min_temp: 0
|
|
max_temp: 250
|
|
|
|
# sensor_type: MAX31865
|
|
# sensor_pin: EBBCan:gpio9
|
|
# spi_software_sclk_pin: EBBCan:gpio10
|
|
# spi_software_mosi_pin: EBBCan:gpio8
|
|
# spi_software_miso_pin: EBBCan:gpio11
|
|
# rtd_nominal_r: 100
|
|
# rtd_reference_r: 430
|
|
# rtd_num_of_wires: 2
|
|
|
|
[tmc2209 extruder]
|
|
uart_pin: EBBCan:gpio20
|
|
run_current: 0.650
|
|
stealthchop_threshold: 999999
|
|
|
|
[fan]
|
|
pin: EBBCan:gpio13
|
|
|
|
[heater_fan hotend_fan]
|
|
pin: EBBCan:gpio14
|
|
heater: extruder
|
|
heater_temp: 50.0
|
|
|
|
[fan_generic 4W_FAN0]
|
|
pin: EBBCan:gpio15
|
|
tachometer_pin: EBBCan:gpio12
|
|
#tachometer_ppr: 1
|
|
|
|
[neopixel hotend_rgb]
|
|
pin: EBBCan:gpio16
|
|
|
|
[bltouch]
|
|
sensor_pin: ^EBBCan:gpio21
|
|
control_pin: EBBCan:gpio22
|
|
|
|
## NPN and PNP proximity switch types can be set by jumper
|
|
#[probe]
|
|
#pin: ^EBBCan:gpio6
|