Add initial files.
This commit is contained in:
585
printer.cfg
Normal file
585
printer.cfg
Normal file
@@ -0,0 +1,585 @@
|
||||
[include mainsail.cfg]
|
||||
|
||||
[mcu]
|
||||
canbus_uuid: 52a031bd2939
|
||||
|
||||
[mcu EBBCan]
|
||||
canbus_uuid: 29e87b131cca
|
||||
|
||||
[printer]
|
||||
kinematics: corexy
|
||||
max_velocity: 300
|
||||
max_accel: 10000
|
||||
max_z_velocity: 30
|
||||
max_z_accel: 350
|
||||
square_corner_velocity: 5.0
|
||||
|
||||
[temperature_sensor MCU]
|
||||
sensor_type: temperature_mcu
|
||||
|
||||
[temperature_sensor SoC]
|
||||
sensor_type: temperature_host
|
||||
|
||||
#####################################################################
|
||||
# X/Y Stepper Settings
|
||||
#####################################################################
|
||||
|
||||
## X Stepper on Motor1 (B Motor)
|
||||
[stepper_x]
|
||||
step_pin: PE6
|
||||
dir_pin: PE5
|
||||
enable_pin: !PC14
|
||||
microsteps: 16
|
||||
rotation_distance: 40
|
||||
full_steps_per_rotation:200 #set to 400 for 0.9 degree stepper
|
||||
endstop_pin: ^EBBCan:gpio24
|
||||
position_min: 0
|
||||
##--------------------------------------------------------------------
|
||||
|
||||
## Uncomment below for 250mm build
|
||||
#position_endstop: 250
|
||||
#position_max: 250
|
||||
|
||||
## Uncomment for 300mm build
|
||||
position_endstop: 300
|
||||
position_max: 300
|
||||
|
||||
## Uncomment for 350mm build
|
||||
#position_endstop: 350
|
||||
#position_max: 350
|
||||
|
||||
##--------------------------------------------------------------------
|
||||
homing_speed: 25
|
||||
homing_retract_dist: 5
|
||||
homing_positive_dir: true
|
||||
|
||||
|
||||
[tmc2209 stepper_x]
|
||||
uart_pin: PC13
|
||||
interpolate: True
|
||||
run_current: 0.9
|
||||
sense_resistor: 0.110
|
||||
stealthchop_threshold: 0
|
||||
|
||||
## Y Stepper on Motor2 (A Motor)
|
||||
[stepper_y]
|
||||
step_pin: PE2
|
||||
dir_pin: PE1
|
||||
enable_pin: !PE4
|
||||
microsteps: 16
|
||||
rotation_distance: 40
|
||||
endstop_pin: ^PF3
|
||||
full_steps_per_rotation:200 #set to 400 for 0.9 degree stepper
|
||||
position_min: 0
|
||||
##--------------------------------------------------------------------
|
||||
|
||||
## Uncomment for 250mm build
|
||||
#position_endstop: 250
|
||||
#position_max: 250
|
||||
|
||||
## Uncomment for 300mm build
|
||||
position_endstop: 300
|
||||
position_max: 300
|
||||
|
||||
## Uncomment for 350mm build
|
||||
#position_endstop: 350
|
||||
#position_max: 350
|
||||
|
||||
##--------------------------------------------------------------------
|
||||
homing_speed: 25
|
||||
homing_retract_dist: 5
|
||||
homing_positive_dir: true
|
||||
|
||||
|
||||
[tmc2209 stepper_y]
|
||||
uart_pin: PE3
|
||||
interpolate: True
|
||||
run_current: 0.9
|
||||
sense_resistor: 0.110
|
||||
stealthchop_threshold: 0
|
||||
|
||||
|
||||
#####################################################################
|
||||
# Z Stepper Settings
|
||||
#####################################################################
|
||||
|
||||
## Z0 Stepper - Front Left on MOTOR3_A
|
||||
[stepper_z]
|
||||
step_pin: PB8
|
||||
dir_pin: PB7
|
||||
enable_pin: !PE0
|
||||
rotation_distance: 40
|
||||
gear_ratio: 80:16
|
||||
microsteps: 16
|
||||
endstop_pin: probe:z_virtual_endstop
|
||||
##--------------------------------------------------------------------
|
||||
|
||||
## Uncomment below for 250mm build
|
||||
#position_max: 240
|
||||
|
||||
## Uncomment below for 300mm build
|
||||
position_max: 290
|
||||
|
||||
## Uncomment below for 350mm build
|
||||
#position_max: 340
|
||||
|
||||
##--------------------------------------------------------------------
|
||||
position_min: -5
|
||||
homing_speed: 8
|
||||
second_homing_speed: 3
|
||||
homing_retract_dist: 3
|
||||
|
||||
|
||||
[tmc2209 stepper_z]
|
||||
uart_pin: PB9
|
||||
interpolate: true
|
||||
run_current: 0.8
|
||||
sense_resistor: 0.110
|
||||
stealthchop_threshold: 0
|
||||
|
||||
## Z1 Stepper - Rear Left on Motor5
|
||||
[stepper_z1]
|
||||
step_pin: PB4
|
||||
dir_pin: !PB3
|
||||
enable_pin: !PB6
|
||||
rotation_distance: 40
|
||||
gear_ratio: 80:16
|
||||
microsteps: 16
|
||||
|
||||
|
||||
[tmc2209 stepper_z1]
|
||||
uart_pin: PB5
|
||||
interpolate: true
|
||||
run_current: 0.8
|
||||
sense_resistor: 0.110
|
||||
stealthchop_threshold: 0
|
||||
|
||||
## Z2 Stepper - Rear Right on Motor6
|
||||
[stepper_z2]
|
||||
step_pin: PG13
|
||||
dir_pin: PG12
|
||||
enable_pin: !PG15
|
||||
rotation_distance: 40
|
||||
gear_ratio: 80:16
|
||||
microsteps: 16
|
||||
|
||||
|
||||
[tmc2209 stepper_z2]
|
||||
uart_pin: PG14
|
||||
interpolate: true
|
||||
run_current: 0.8
|
||||
sense_resistor: 0.110
|
||||
stealthchop_threshold: 0
|
||||
|
||||
## Z3 Stepper - Front Right on Motor7
|
||||
[stepper_z3]
|
||||
step_pin: PG9
|
||||
dir_pin: !PD7
|
||||
enable_pin: !PG11
|
||||
rotation_distance: 40
|
||||
gear_ratio: 80:16
|
||||
microsteps: 16
|
||||
|
||||
|
||||
[tmc2209 stepper_z3]
|
||||
uart_pin: PG10
|
||||
interpolate: true
|
||||
run_current: 0.8
|
||||
sense_resistor: 0.110
|
||||
stealthchop_threshold: 0
|
||||
|
||||
#####################################################################
|
||||
# Extruder
|
||||
#####################################################################
|
||||
|
||||
# E0 on SB2209
|
||||
[extruder]
|
||||
step_pin: EBBCan:gpio18
|
||||
dir_pin: EBBCan:gpio19
|
||||
enable_pin: !EBBCan:gpio17
|
||||
microsteps: 16
|
||||
rotation_distance: 22.905740611
|
||||
gear_ratio: 50:10
|
||||
nozzle_diameter: 0.400
|
||||
filament_diameter: 1.750
|
||||
heater_pin: EBBCan:gpio7
|
||||
#control: pid
|
||||
min_temp: 0
|
||||
max_temp: 300
|
||||
max_extrude_only_distance: 105
|
||||
max_extrude_cross_section: 2
|
||||
#pid_kp: 57.369
|
||||
#pid_ki: 2.533
|
||||
#pid_kd: 324.854
|
||||
sensor_type: MAX31865
|
||||
sensor_pin: EBBCan:gpio9
|
||||
spi_software_sclk_pin: EBBCan:gpio10
|
||||
spi_software_mosi_pin: EBBCan:gpio8
|
||||
spi_software_miso_pin: EBBCan:gpio11
|
||||
rtd_nominal_r: 100
|
||||
rtd_reference_r: 430
|
||||
rtd_num_of_wires: 2
|
||||
pressure_advance: 0.03
|
||||
|
||||
[tmc2209 extruder]
|
||||
uart_pin: EBBCan:gpio20
|
||||
run_current: 0.65
|
||||
stealthchop_threshold: 0
|
||||
|
||||
|
||||
#####################################################################
|
||||
# Bed Heater
|
||||
#####################################################################
|
||||
|
||||
[heater_bed]
|
||||
heater_pin: PA1
|
||||
sensor_type: Generic 3950
|
||||
sensor_pin: PB1
|
||||
max_power: 1.0
|
||||
min_temp: 0
|
||||
max_temp: 115
|
||||
#control: pid
|
||||
#pid_kp: 58.437
|
||||
#pid_ki: 2.347
|
||||
#pid_kd: 363.769
|
||||
|
||||
|
||||
#####################################################################
|
||||
# Probe
|
||||
#####################################################################
|
||||
|
||||
[probe]
|
||||
pin: ^EBBCan:gpio22
|
||||
x_offset: 0
|
||||
y_offset: 0
|
||||
#z_offset: 0
|
||||
lift_speed: 30
|
||||
activate_gcode:
|
||||
{% set PROBE_TEMP = 150 %}
|
||||
{% set MAX_TEMP = PROBE_TEMP + 5 %}
|
||||
{% set ACTUAL_TEMP = printer.extruder.temperature %}
|
||||
{% set TARGET_TEMP = printer.extruder.target %}
|
||||
|
||||
{% if TARGET_TEMP > PROBE_TEMP %}
|
||||
{ action_respond_info('Extruder temperature target of %.1fC is too high, lowering to %.1fC' % (TARGET_TEMP, PROBE_TEMP)) }
|
||||
M109 S{ PROBE_TEMP }
|
||||
{% else %}
|
||||
# Temperature target is already low enough, but nozzle may still be too hot.
|
||||
{% if ACTUAL_TEMP > MAX_TEMP %}
|
||||
{ action_respond_info('Extruder temperature %.1fC is still too high, waiting until below %.1fC' % (ACTUAL_TEMP, MAX_TEMP)) }
|
||||
TEMPERATURE_WAIT SENSOR=extruder MAXIMUM={ MAX_TEMP }
|
||||
{% endif %}
|
||||
{% endif %}
|
||||
|
||||
#####################################################################
|
||||
# Fan Control
|
||||
#####################################################################
|
||||
|
||||
[fan]
|
||||
pin: EBBCan:gpio13
|
||||
|
||||
[heater_fan hotend_fan]
|
||||
pin: EBBCan:gpio14
|
||||
heater: extruder
|
||||
heater_temp: 70.0
|
||||
|
||||
|
||||
[fan_generic nevermore]
|
||||
## Print Cooling Fan - CNC_FAN0
|
||||
pin: PF8
|
||||
kick_start_time: 0.5
|
||||
off_below: 0.10
|
||||
|
||||
[controller_fan controller_fan_1]
|
||||
## Hotend Fan - CNC_FAN1
|
||||
pin: PF9
|
||||
max_power: 1.0
|
||||
kick_start_time: 0.5
|
||||
fan_speed: 0.66
|
||||
|
||||
|
||||
[heater_fan controller_fan_2]
|
||||
## Controller fan - CNC_FAN2
|
||||
pin: PF6
|
||||
kick_start_time: 0.5
|
||||
heater: heater_bed
|
||||
heater_temp: 80
|
||||
fan_speed: 0.66
|
||||
|
||||
[fan_generic exhaust_fan]
|
||||
# Exhaust fan - CNC_FAN0
|
||||
pin: PF7
|
||||
max_power: 1.0
|
||||
shutdown_speed: 0.0
|
||||
kick_start_time: 0.5
|
||||
|
||||
#####################################################################
|
||||
# LED Control
|
||||
#####################################################################
|
||||
|
||||
#[neopixel toolhead_light]
|
||||
#pin: EBBCan:gpio16
|
||||
#chain_count: 3
|
||||
#color_order: GRBW
|
||||
[include stealthburner_leds.cfg]
|
||||
|
||||
[output_pin caselight]
|
||||
#Chamber Lighting - HE3 Connector
|
||||
pin: PA3
|
||||
pwm:true
|
||||
shutdown_value: 0
|
||||
cycle_time: 0.01
|
||||
|
||||
#####################################################################
|
||||
# Homing and Gantry Adjustment Routines
|
||||
#####################################################################
|
||||
|
||||
[idle_timeout]
|
||||
timeout: 3300
|
||||
|
||||
[safe_z_home]
|
||||
##--------------------------------------------------------------------
|
||||
|
||||
## Uncomment below for 250mm build
|
||||
#home_xy_position: 125,125
|
||||
|
||||
## Uncomment below for 300mm build
|
||||
home_xy_position: 150,150
|
||||
|
||||
## Uncomment below for 350mm build
|
||||
#home_xy_position: 175,175
|
||||
|
||||
##--------------------------------------------------------------------
|
||||
speed: 100
|
||||
z_hop: 10
|
||||
|
||||
[quad_gantry_level]
|
||||
## Use QUAD_GANTRY_LEVEL to level a gantry.
|
||||
## Min & Max gantry corners - measure from nozzle at MIN (0,0) and
|
||||
## MAX (250, 250), (300,300), or (350,350) depending on your printer size
|
||||
## to respective belt positions
|
||||
|
||||
#--------------------------------------------------------------------
|
||||
## Gantry Corners for 250mm Build
|
||||
## Uncomment for 250mm build
|
||||
#gantry_corners:
|
||||
# -60,-10
|
||||
# 310, 320
|
||||
## Probe points
|
||||
#points:
|
||||
# 50,25
|
||||
# 50,175
|
||||
# 200,175
|
||||
# 200,25
|
||||
|
||||
## Gantry Corners for 300mm Build
|
||||
## Uncomment for 300mm build
|
||||
gantry_corners:
|
||||
-60,-10
|
||||
360,370
|
||||
# Probe points
|
||||
points:
|
||||
50,25
|
||||
50,225
|
||||
250,225
|
||||
250,25
|
||||
|
||||
## Gantry Corners for 350mm Build
|
||||
## Uncomment for 350mm build
|
||||
#gantry_corners:
|
||||
# -60,-10
|
||||
# 410,420
|
||||
## Probe points
|
||||
#points:
|
||||
# 50,25
|
||||
# 50,275
|
||||
# 300,275
|
||||
# 300,25
|
||||
|
||||
#--------------------------------------------------------------------
|
||||
speed: 100
|
||||
horizontal_move_z: 10
|
||||
retries: 10
|
||||
retry_tolerance: 0.0075
|
||||
max_adjust: 10
|
||||
|
||||
[bed_mesh]
|
||||
mesh_min: 10,10
|
||||
##--------------------------------------------------------------------
|
||||
|
||||
## Uncomment below for 250mm build
|
||||
#mesh_max: 240,240
|
||||
|
||||
## Uncomment below for 300mm build
|
||||
mesh_max: 290,290
|
||||
|
||||
|
||||
## Uncomment below for 350mm build
|
||||
#mesh_max: 340,340
|
||||
|
||||
##--------------------------------------------------------------------
|
||||
|
||||
[adxl345]
|
||||
cs_pin: EBBCan:gpio1
|
||||
spi_software_sclk_pin: EBBCan:gpio2
|
||||
spi_software_mosi_pin: EBBCan:gpio0
|
||||
spi_software_miso_pin: EBBCan:gpio3
|
||||
axes_map: z,-y,x
|
||||
|
||||
|
||||
[board_pins]
|
||||
aliases:
|
||||
# EXP1 header
|
||||
EXP1_1=PE7, EXP1_2=PG1,
|
||||
EXP1_3=PG0, EXP1_4=PF15,
|
||||
EXP1_5=PF14, EXP1_6=PF13, # Slot in the socket on this side
|
||||
EXP1_7=PF12, EXP1_8=PF11,
|
||||
EXP1_9=<GND>, EXP1_10=<5V>,
|
||||
|
||||
# EXP2 header
|
||||
EXP2_1=PE13, EXP2_2=PE12,
|
||||
EXP2_3=PE15, EXP2_4=PE11,
|
||||
EXP2_5=PE10, EXP2_6=PE14, # Slot in the socket on this side
|
||||
EXP2_7=PE8, EXP2_8=<RST>,
|
||||
EXP2_9=<GND>, EXP2_10=<NC>
|
||||
|
||||
|
||||
#####################################################################
|
||||
# Macros
|
||||
#####################################################################
|
||||
|
||||
# Conditional G28 (home if not already homed)
|
||||
[gcode_macro CG28]
|
||||
gcode:
|
||||
{% if "x" not in printer.toolhead.homed_axes or "y" not in printer.toolhead.homed_axes or "z" not in printer.toolhead.homed_axes %}
|
||||
M117 Homing
|
||||
G28
|
||||
{% endif %}
|
||||
|
||||
|
||||
|
||||
#[gcode_macro G32]
|
||||
#gcode:
|
||||
# BED_MESH_CLEAR
|
||||
# CG28 ; Home if not homed to get everything turned on
|
||||
# QUAD_GANTRY_LEVEL ; Level
|
||||
# #G28 X Y ; Home the X and Y
|
||||
# G0 X130 Y355 Z2 F9000 ; Move to brush
|
||||
# G0 X75 F750 ; Move across the brush
|
||||
# G0 X130 F750 ; Move across the brush
|
||||
# G28 Z ; Home the Z now that nozzle is clean
|
||||
# G0 X150 Y150 Z20 F6000 ; Return to center of bed
|
||||
|
||||
|
||||
[gcode_macro G32]
|
||||
gcode:
|
||||
|
||||
STATUS_HOMING
|
||||
BED_MESH_CLEAR
|
||||
CG28
|
||||
|
||||
STATUS_LEVELING
|
||||
M117 Leveling Gantry
|
||||
QUAD_GANTRY_LEVEL
|
||||
G28
|
||||
## Uncomment for for your size printer:
|
||||
#--------------------------------------------------------------------
|
||||
## Uncomment for 250mm build
|
||||
#G0 X125 Y125 Z30 F3600
|
||||
|
||||
## Uncomment for 300 build
|
||||
G0 X150 Y150 Z30 F3600
|
||||
|
||||
## Uncomment for 350mm build
|
||||
#G0 X175 Y175 Z30 F3600
|
||||
#--------------------------------------------------------------------
|
||||
|
||||
M117
|
||||
STATUS_READY
|
||||
|
||||
[gcode_macro PRINT_START]
|
||||
gcode:
|
||||
{% set BED = params.BED|default(60)|int %}
|
||||
{% set EXTRUDER = params.EXTRUDER|default(210)|int %}
|
||||
|
||||
SAVE_GCODE_STATE NAME=start
|
||||
|
||||
SET_PIN pin=caselight value=0.50
|
||||
|
||||
STATUS_HEATING
|
||||
M117 Starting warmup
|
||||
M140 S{BED}
|
||||
CG28
|
||||
G1 Z20 F3000 ; move nozzle away from bed
|
||||
|
||||
# Heat bed first
|
||||
# Heat nozzle to 140
|
||||
STATUS_HEATING
|
||||
M104 S140
|
||||
M190 S{BED}
|
||||
|
||||
# Home and QGL while nozzle is cold
|
||||
M117 Homing
|
||||
G32
|
||||
|
||||
# Now heat nozzle
|
||||
M117 Heating Nozzle
|
||||
STATUS_HEATING
|
||||
M109 S{EXTRUDER}
|
||||
|
||||
M117 #Clear Status
|
||||
STATUS_PRINTING
|
||||
|
||||
RESTORE_GCODE_STATE NAME=start
|
||||
|
||||
|
||||
[gcode_macro PRINT_END]
|
||||
# Use PRINT_END for the slicer ending script - please customise for your slicer of choice
|
||||
gcode:
|
||||
SAVE_GCODE_STATE NAME=STATE_PRINT_END
|
||||
|
||||
M400 ; wait for buffer to clear
|
||||
G92 E0 ; zero the extruder
|
||||
G1 E-10.0 F3600 ; retract filament
|
||||
|
||||
G91 ; relative positioning
|
||||
G0 Z1.00 X20.0 Y20.0 F20000 ; move nozzle to remove stringing
|
||||
TURN_OFF_HEATERS
|
||||
M107 ; turn off fan
|
||||
G1 Z2 F3000 ; move nozzle up 2mm
|
||||
G90 ; absolute positioning
|
||||
G0 X125 Y250 F3600 ; park nozzle at rear
|
||||
|
||||
SET_PIN pin=caselight value=0.03
|
||||
|
||||
BED_MESH_CLEAR
|
||||
|
||||
STATUS_READY
|
||||
|
||||
# The purpose of the SAVE_GCODE_STATE/RESTORE_GCODE_STATE
|
||||
# command pair is to restore the printer's coordinate system
|
||||
# and speed settings since the commands above change them.
|
||||
# However, to prevent any accidental, unintentional toolhead
|
||||
# moves when restoring the state, explicitly set MOVE=0.
|
||||
RESTORE_GCODE_STATE NAME=STATE_PRINT_END MOVE=0
|
||||
|
||||
[force_move]
|
||||
enable_force_move: true
|
||||
|
||||
#*# <---------------------- SAVE_CONFIG ---------------------->
|
||||
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
|
||||
#*#
|
||||
#*# [heater_bed]
|
||||
#*# control = pid
|
||||
#*# pid_kp = 63.521
|
||||
#*# pid_ki = 2.900
|
||||
#*# pid_kd = 347.777
|
||||
#*#
|
||||
#*# [extruder]
|
||||
#*# control = pid
|
||||
#*# pid_kp = 16.710
|
||||
#*# pid_ki = 1.061
|
||||
#*# pid_kd = 65.795
|
||||
#*#
|
||||
#*# [probe]
|
||||
#*# z_offset = -1.575
|
||||
Reference in New Issue
Block a user