Actually fix quad gantry level order. Delete some lines for other build sizes.

printer.cfg

@@ -338,18 +338,7 @@ cycle_time: 0.01
 timeout: 3300
 
 [safe_z_home]
-##--------------------------------------------------------------------
-
-##	Uncomment below for 250mm build
-#home_xy_position: 125,125
-
-##	Uncomment below for 300mm build
 home_xy_position: 150,150
-
-##	Uncomment below for 350mm build
-#home_xy_position: 175,175
-
-##--------------------------------------------------------------------
 speed: 100
 z_hop: 10
 
@@ -358,46 +347,14 @@ z_hop: 10
 ##	Min & Max gantry corners - measure from nozzle at MIN (0,0) and
 ##	MAX (250, 250), (300,300), or (350,350) depending on your printer size
 ##	to respective belt positions
-
-#--------------------------------------------------------------------
-##	Gantry Corners for 250mm Build
-##	Uncomment for 250mm build
-#gantry_corners:
-#	-60,-10
-#	310, 320
-##	Probe points
-#points:
-#	50,25
-#	50,175
-#	200,175
-#	200,25
-
-##	Gantry Corners for 300mm Build
-##	Uncomment for 300mm build
 gantry_corners:
 	-60,-10
 	360,370
-
+points: 
-#	Probe points
+    40, 260
-points:
+    40, 40
-    275,25
+    260,40
-	25,25
+    260,260
-	25,275
-	275,275
-
-##	Gantry Corners for 350mm Build
-##	Uncomment for 350mm build
-#gantry_corners:
-#	-60,-10
-#	410,420
-##	Probe points
-#points:
-#	50,25
-#	50,275
-#	300,275
-#	300,25
-
-#--------------------------------------------------------------------
 speed: 100
 horizontal_move_z: 10
 retries: 10
@@ -406,20 +363,8 @@ max_adjust: 10
 
 [bed_mesh]
 mesh_min: 10,10
-##--------------------------------------------------------------------
-
-##	Uncomment below for 250mm build
-#mesh_max: 240,240
-
-##	Uncomment below for 300mm build
 mesh_max: 290,290
 
-
-##	Uncomment below for 350mm build
-#mesh_max: 340,340
-
-##--------------------------------------------------------------------
-
 [adxl345]
 cs_pin: EBBCan:gpio1
 spi_software_sclk_pin: EBBCan:gpio2
@@ -430,10 +375,8 @@ axes_map: z,-y,x
 [resonance_tester]
 accel_chip: adxl345
 probe_points:
-    # Somewhere slightly above the middle of your print bed
     150,150, 20
 
-
 [board_pins]
 aliases:
     # EXP1 header
@@ -463,21 +406,6 @@ gcode:
     G28
     {% endif %}
 
-
-
-#[gcode_macro G32]
-#gcode:
-#    BED_MESH_CLEAR
-#    CG28                      ; Home if not homed to get everything turned on
-#    QUAD_GANTRY_LEVEL         ; Level
-#    #G28 X Y                  ; Home the X and Y
-#    G0 X130 Y355 Z2 F9000     ; Move to brush
-#    G0 X75 F750               ; Move across the brush
-#    G0 X130 F750              ; Move across the brush
-#    G28 Z                     ; Home the Z now that nozzle is clean
-#    G0 X150 Y150 Z20 F6000    ; Return to center of bed
-
-
 [gcode_macro G32]
 gcode:
 
@@ -489,18 +417,9 @@ gcode:
     M117 Leveling Gantry
     QUAD_GANTRY_LEVEL
     G28
-    ##	Uncomment for for your size printer:
+    
-    #--------------------------------------------------------------------
-    ##	Uncomment for 250mm build
-    #G0 X125 Y125 Z30 F3600
-
-    ##	Uncomment for 300 build
     G0 X150 Y150 Z30 F3600
 
-    ##	Uncomment for 350mm build
-    #G0 X175 Y175 Z30 F3600
-    #--------------------------------------------------------------------
-
     M117
     STATUS_READY