87 lines
2.7 KiB
C++
87 lines
2.7 KiB
C++
/**
|
|
* Marlin 3D Printer Firmware
|
|
* Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
|
|
*
|
|
* Based on Sprinter and grbl.
|
|
* Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
|
|
*
|
|
* This program is free software: you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License as published by
|
|
* the Free Software Foundation, either version 3 of the License, or
|
|
* (at your option) any later version.
|
|
*
|
|
* This program is distributed in the hope that it will be useful,
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
* GNU General Public License for more details.
|
|
*
|
|
* You should have received a copy of the GNU General Public License
|
|
* along with this program. If not, see <http://www.gnu.org/licenses/>.
|
|
*
|
|
*/
|
|
|
|
#include "../../inc/MarlinConfig.h"
|
|
|
|
#if HAS_M206_COMMAND
|
|
|
|
#include "../gcode.h"
|
|
#include "../../module/motion.h"
|
|
#include "../../lcd/ultralcd.h"
|
|
#include "../../libs/buzzer.h"
|
|
|
|
/**
|
|
* M206: Set Additional Homing Offset (X Y Z). SCARA aliases T=X, P=Y
|
|
*
|
|
* *** @thinkyhead: I recommend deprecating M206 for SCARA in favor of M665.
|
|
* *** M206 for SCARA will remain enabled in 1.1.x for compatibility.
|
|
* *** In the 2.0 release, it will simply be disabled by default.
|
|
*/
|
|
void GcodeSuite::M206() {
|
|
LOOP_XYZ(i)
|
|
if (parser.seen(XYZ_CHAR(i)))
|
|
set_home_offset((AxisEnum)i, parser.value_linear_units());
|
|
|
|
#if ENABLED(MORGAN_SCARA)
|
|
if (parser.seen('T')) set_home_offset(A_AXIS, parser.value_float()); // Theta
|
|
if (parser.seen('P')) set_home_offset(B_AXIS, parser.value_float()); // Psi
|
|
#endif
|
|
|
|
report_current_position();
|
|
}
|
|
|
|
/**
|
|
* M428: Set home_offset based on the distance between the
|
|
* current_position and the nearest "reference point."
|
|
* If an axis is past center its endstop position
|
|
* is the reference-point. Otherwise it uses 0. This allows
|
|
* the Z offset to be set near the bed when using a max endstop.
|
|
*
|
|
* M428 can't be used more than 2cm away from 0 or an endstop.
|
|
*
|
|
* Use M206 to set these values directly.
|
|
*/
|
|
void GcodeSuite::M428() {
|
|
if (axis_unhomed_error()) return;
|
|
|
|
xyz_float_t diff;
|
|
LOOP_XYZ(i) {
|
|
diff[i] = base_home_pos((AxisEnum)i) - current_position[i];
|
|
if (!WITHIN(diff[i], -20, 20) && home_dir((AxisEnum)i) > 0)
|
|
diff[i] = -current_position[i];
|
|
if (!WITHIN(diff[i], -20, 20)) {
|
|
SERIAL_ERROR_MSG(STR_ERR_M428_TOO_FAR);
|
|
LCD_ALERTMESSAGEPGM_P(PSTR("Err: Too far!"));
|
|
BUZZ(200, 40);
|
|
return;
|
|
}
|
|
}
|
|
|
|
LOOP_XYZ(i) set_home_offset((AxisEnum)i, diff[i]);
|
|
report_current_position();
|
|
LCD_MESSAGEPGM(MSG_HOME_OFFSETS_APPLIED);
|
|
BUZZ(100, 659);
|
|
BUZZ(100, 698);
|
|
}
|
|
|
|
#endif // HAS_M206_COMMAND
|