286 lines
8.2 KiB
C++
286 lines
8.2 KiB
C++
/**
|
|
* Marlin 3D Printer Firmware
|
|
* Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
|
|
*
|
|
* Based on Sprinter and grbl.
|
|
* Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
|
|
*
|
|
* This program is free software: you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License as published by
|
|
* the Free Software Foundation, either version 3 of the License, or
|
|
* (at your option) any later version.
|
|
*
|
|
* This program is distributed in the hope that it will be useful,
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
* GNU General Public License for more details.
|
|
*
|
|
* You should have received a copy of the GNU General Public License
|
|
* along with this program. If not, see <https://www.gnu.org/licenses/>.
|
|
*
|
|
*/
|
|
|
|
#include "../inc/MarlinConfig.h"
|
|
|
|
#if ENABLED(IIC_BL24CXX_EEPROM)
|
|
|
|
/**
|
|
* PersistentStore for Arduino-style EEPROM interface
|
|
* with simple implementations supplied by Marlin.
|
|
*/
|
|
|
|
#include "BL24CXX.h"
|
|
#ifdef __STM32F1__
|
|
#include <libmaple/gpio.h>
|
|
#else
|
|
#include "../HAL/shared/Delay.h"
|
|
#define delay_us(n) DELAY_US(n)
|
|
#endif
|
|
|
|
#ifndef EEPROM_WRITE_DELAY
|
|
#define EEPROM_WRITE_DELAY 10
|
|
#endif
|
|
#ifndef EEPROM_DEVICE_ADDRESS
|
|
#define EEPROM_DEVICE_ADDRESS (0x50 << 1)
|
|
#endif
|
|
|
|
// IO direction setting
|
|
#ifdef __STM32F1__
|
|
#define SDA_IN() do{ PIN_MAP[IIC_EEPROM_SDA].gpio_device->regs->CRH &= 0XFFFF0FFF; PIN_MAP[IIC_EEPROM_SDA].gpio_device->regs->CRH |= 8 << 12; }while(0)
|
|
#define SDA_OUT() do{ PIN_MAP[IIC_EEPROM_SDA].gpio_device->regs->CRH &= 0XFFFF0FFF; PIN_MAP[IIC_EEPROM_SDA].gpio_device->regs->CRH |= 3 << 12; }while(0)
|
|
#elif STM32F1
|
|
#define SDA_IN() SET_INPUT(IIC_EEPROM_SDA)
|
|
#define SDA_OUT() SET_OUTPUT(IIC_EEPROM_SDA)
|
|
#endif
|
|
|
|
// IO ops
|
|
#define IIC_SCL_0() WRITE(IIC_EEPROM_SCL, LOW)
|
|
#define IIC_SCL_1() WRITE(IIC_EEPROM_SCL, HIGH)
|
|
#define IIC_SDA_0() WRITE(IIC_EEPROM_SDA, LOW)
|
|
#define IIC_SDA_1() WRITE(IIC_EEPROM_SDA, HIGH)
|
|
#define READ_SDA() READ(IIC_EEPROM_SDA)
|
|
|
|
//
|
|
// Simple IIC interface via libmaple
|
|
//
|
|
|
|
// Initialize IIC
|
|
void IIC::init() {
|
|
SET_OUTPUT(IIC_EEPROM_SDA);
|
|
SET_OUTPUT(IIC_EEPROM_SCL);
|
|
IIC_SCL_1();
|
|
IIC_SDA_1();
|
|
}
|
|
|
|
// Generate IIC start signal
|
|
void IIC::start() {
|
|
SDA_OUT(); // SDA line output
|
|
IIC_SDA_1();
|
|
IIC_SCL_1();
|
|
delay_us(4);
|
|
IIC_SDA_0(); // START:when CLK is high, DATA change from high to low
|
|
delay_us(4);
|
|
IIC_SCL_0(); // Clamp the I2C bus, ready to send or receive data
|
|
}
|
|
|
|
// Generate IIC stop signal
|
|
void IIC::stop() {
|
|
SDA_OUT(); // SDA line output
|
|
IIC_SCL_0();
|
|
IIC_SDA_0(); // STOP:when CLK is high DATA change from low to high
|
|
delay_us(4);
|
|
IIC_SCL_1();
|
|
IIC_SDA_1(); // Send I2C bus end signal
|
|
delay_us(4);
|
|
}
|
|
|
|
// Wait for the response signal to arrive
|
|
// 1 = failed to receive response
|
|
// 0 = response received
|
|
uint8_t IIC::wait_ack() {
|
|
uint8_t ucErrTime = 0;
|
|
SDA_IN(); // SDA is set as input
|
|
IIC_SDA_1(); delay_us(1);
|
|
IIC_SCL_1(); delay_us(1);
|
|
while (READ_SDA()) {
|
|
if (++ucErrTime > 250) {
|
|
stop();
|
|
return 1;
|
|
}
|
|
}
|
|
IIC_SCL_0(); // Clock output 0
|
|
return 0;
|
|
}
|
|
|
|
// Generate ACK response
|
|
void IIC::ack() {
|
|
IIC_SCL_0();
|
|
SDA_OUT();
|
|
IIC_SDA_0();
|
|
delay_us(2);
|
|
IIC_SCL_1();
|
|
delay_us(2);
|
|
IIC_SCL_0();
|
|
}
|
|
|
|
// No ACK response
|
|
void IIC::nAck() {
|
|
IIC_SCL_0();
|
|
SDA_OUT();
|
|
IIC_SDA_1();
|
|
delay_us(2);
|
|
IIC_SCL_1();
|
|
delay_us(2);
|
|
IIC_SCL_0();
|
|
}
|
|
|
|
// Send one IIC byte
|
|
// Return whether the slave responds
|
|
// 1 = there is a response
|
|
// 0 = no response
|
|
void IIC::send_byte(uint8_t txd) {
|
|
SDA_OUT();
|
|
IIC_SCL_0(); // Pull down the clock to start data transmission
|
|
LOOP_L_N(t, 8) {
|
|
// IIC_SDA = (txd & 0x80) >> 7;
|
|
if (txd & 0x80) IIC_SDA_1(); else IIC_SDA_0();
|
|
txd <<= 1;
|
|
delay_us(2); // All three delays are necessary for TEA5767
|
|
IIC_SCL_1();
|
|
delay_us(2);
|
|
IIC_SCL_0();
|
|
delay_us(2);
|
|
}
|
|
}
|
|
|
|
// Read 1 byte, when ack=1, send ACK, ack=0, send nACK
|
|
uint8_t IIC::read_byte(unsigned char ack_chr) {
|
|
unsigned char receive = 0;
|
|
SDA_IN(); // SDA is set as input
|
|
LOOP_L_N(i, 8) {
|
|
IIC_SCL_0();
|
|
delay_us(2);
|
|
IIC_SCL_1();
|
|
receive <<= 1;
|
|
if (READ_SDA()) receive++;
|
|
delay_us(1);
|
|
}
|
|
ack_chr ? ack() : nAck(); // Send ACK / send nACK
|
|
return receive;
|
|
}
|
|
|
|
/******************** EEPROM ********************/
|
|
|
|
// Initialize the IIC interface
|
|
void BL24CXX::init() { IIC::init(); }
|
|
|
|
// Read a byte at the specified address
|
|
// ReadAddr: the address to start reading
|
|
// Return: the byte read
|
|
uint8_t BL24CXX::readOneByte(uint16_t ReadAddr) {
|
|
uint8_t temp = 0;
|
|
IIC::start();
|
|
if (EE_TYPE > BL24C16) {
|
|
IIC::send_byte(EEPROM_DEVICE_ADDRESS); // Send write command
|
|
IIC::wait_ack();
|
|
IIC::send_byte(ReadAddr >> 8); // Send high address
|
|
IIC::wait_ack();
|
|
}
|
|
else
|
|
IIC::send_byte(EEPROM_DEVICE_ADDRESS + ((ReadAddr >> 8) << 1)); // Send device address 0xA0, write data
|
|
|
|
IIC::wait_ack();
|
|
IIC::send_byte(ReadAddr & 0xFF); // Send low address
|
|
IIC::wait_ack();
|
|
IIC::start();
|
|
IIC::send_byte(EEPROM_DEVICE_ADDRESS | 0x01); // Send byte
|
|
IIC::wait_ack();
|
|
temp = IIC::read_byte(0);
|
|
IIC::stop(); // Generate a stop condition
|
|
return temp;
|
|
}
|
|
|
|
// Write a data at the address specified by BL24CXX
|
|
// WriteAddr: The destination address for writing data
|
|
// DataToWrite: the data to be written
|
|
void BL24CXX::writeOneByte(uint16_t WriteAddr, uint8_t DataToWrite) {
|
|
IIC::start();
|
|
if (EE_TYPE > BL24C16) {
|
|
IIC::send_byte(EEPROM_DEVICE_ADDRESS); // Send write command
|
|
IIC::wait_ack();
|
|
IIC::send_byte(WriteAddr >> 8); // Send high address
|
|
}
|
|
else
|
|
IIC::send_byte(EEPROM_DEVICE_ADDRESS + ((WriteAddr >> 8) << 1)); // Send device address 0xA0, write data
|
|
|
|
IIC::wait_ack();
|
|
IIC::send_byte(WriteAddr & 0xFF); // Send low address
|
|
IIC::wait_ack();
|
|
IIC::send_byte(DataToWrite); // Receiving mode
|
|
IIC::wait_ack();
|
|
IIC::stop(); // Generate a stop condition
|
|
delay(10);
|
|
}
|
|
|
|
// Start writing data of length Len at the specified address in BL24CXX
|
|
// This function is used to write 16bit or 32bit data.
|
|
// WriteAddr: the address to start writing
|
|
// DataToWrite: the first address of the data array
|
|
// Len: The length of the data to be written 2, 4
|
|
void BL24CXX::writeLenByte(uint16_t WriteAddr, uint32_t DataToWrite, uint8_t Len) {
|
|
LOOP_L_N(t, Len)
|
|
writeOneByte(WriteAddr + t, (DataToWrite >> (8 * t)) & 0xFF);
|
|
}
|
|
|
|
// Start reading data of length Len from the specified address in BL24CXX
|
|
// This function is used to read 16bit or 32bit data.
|
|
// ReadAddr: the address to start reading
|
|
// Return value: data
|
|
// Len: The length of the data to be read 2,4
|
|
uint32_t BL24CXX::readLenByte(uint16_t ReadAddr, uint8_t Len) {
|
|
uint32_t temp = 0;
|
|
LOOP_L_N(t, Len) {
|
|
temp <<= 8;
|
|
temp += readOneByte(ReadAddr + Len - t - 1);
|
|
}
|
|
return temp;
|
|
}
|
|
|
|
// Check if BL24CXX is normal
|
|
// Return 1: Detection failed
|
|
// return 0: detection is successful
|
|
#define BL24CXX_TEST_ADDRESS 0x00
|
|
#define BL24CXX_TEST_VALUE 0x55
|
|
|
|
bool BL24CXX::_check() {
|
|
return (readOneByte(BL24CXX_TEST_ADDRESS) != BL24CXX_TEST_VALUE); // false = success!
|
|
}
|
|
|
|
bool BL24CXX::check() {
|
|
if (_check()) { // Value was written? Good EEPROM!
|
|
writeOneByte(BL24CXX_TEST_ADDRESS, BL24CXX_TEST_VALUE); // Write now and check.
|
|
return _check();
|
|
}
|
|
return false; // success!
|
|
}
|
|
|
|
// Start reading the specified number of data at the specified address in BL24CXX
|
|
// ReadAddr: The address to start reading is 0~255 for 24c02
|
|
// pBuffer: the first address of the data array
|
|
// NumToRead: the number of data to be read
|
|
void BL24CXX::read(uint16_t ReadAddr, uint8_t *pBuffer, uint16_t NumToRead) {
|
|
for (; NumToRead; NumToRead--)
|
|
*pBuffer++ = readOneByte(ReadAddr++);
|
|
}
|
|
|
|
// Start writing the specified number of data at the specified address in BL24CXX
|
|
// WriteAddr: the address to start writing, 0~255 for 24c02
|
|
// pBuffer: the first address of the data array
|
|
// NumToWrite: the number of data to be written
|
|
void BL24CXX::write(uint16_t WriteAddr, uint8_t *pBuffer, uint16_t NumToWrite) {
|
|
for (; NumToWrite; NumToWrite--, WriteAddr++)
|
|
writeOneByte(WriteAddr, *pBuffer++);
|
|
}
|
|
|
|
#endif // IIC_BL24CXX_EEPROM
|