Roxy-3D bfd9728cf4 Serial buffer over run work around for v2.0.0 (#9236) ... * Work around for serial buffer over run PronterFace sends a lot of M105 commands. During long operations such as UBL's G29 P1, G29 P2, G29 P4 and G26 this can over run the serial buffer. This results (very often) in a M1 (actually a M1M105) ending up in the command queue. Until we figure out a better way to resolve this issue, this will keep the UBL commands from experiencing bogus commands at thier completion.		2018-01-18 19:57:18 -06:00
..
adafruit/ST7565	Followup to Ender config	2018-01-15 06:00:21 -06:00
AlephObjects/TAZ4	Followup to Ender config	2018-01-15 06:00:21 -06:00
AliExpress/CL-260	Followup to Ender config	2018-01-15 06:00:21 -06:00
Anet	Followup to Ender config	2018-01-15 06:00:21 -06:00
Azteeg/X5GT	Followup to Ender config	2018-01-15 06:00:21 -06:00
BQ	Followup to Ender config	2018-01-15 06:00:21 -06:00
Cartesio	Followup to Ender config	2018-01-15 06:00:21 -06:00
Creality	Followup to Ender config	2018-01-15 06:00:21 -06:00
delta	Followup to Ender config	2018-01-15 06:00:21 -06:00
Felix	Followup to Ender config	2018-01-15 06:00:21 -06:00
FolgerTech/i3-2020	Serial buffer over run work around for v2.0.0 (#9236)	2018-01-18 19:57:18 -06:00
gCreate/gMax1.5+	Convert UBL mesh tilting to all use the same algorithm (#9204)	2018-01-16 11:08:00 -06:00
Geeetech	Followup to Ender config	2018-01-15 06:00:21 -06:00
Infitary/i3-M508	Followup to Ender config	2018-01-15 06:00:21 -06:00
MakerParts	Followup to Ender config	2018-01-15 06:00:21 -06:00
makibox	Followup to Ender config	2018-01-15 06:00:21 -06:00
Malyan	Followup to Ender config	2018-01-15 06:00:21 -06:00
Micromake/C1	Followup to Ender config	2018-01-15 06:00:21 -06:00
Mks/Sbase	Followup to Ender config	2018-01-15 06:00:21 -06:00
RepRapWorld/Megatronics	Followup to Ender config	2018-01-15 06:00:21 -06:00
RigidBot	Followup to Ender config	2018-01-15 06:00:21 -06:00
Sanguinololu	Followup to Ender config	2018-01-15 06:00:21 -06:00
SCARA	Followup to Ender config	2018-01-15 06:00:21 -06:00
stm32f103ret6	Followup to Ender config	2018-01-15 06:00:21 -06:00
STM32F10	Followup to Ender config	2018-01-15 06:00:21 -06:00
TheBorg	Followup to Ender config	2018-01-15 06:00:21 -06:00
TinyBoy2	Followup to Ender config	2018-01-15 06:00:21 -06:00
Tronxy/X1	Followup to Ender config	2018-01-15 06:00:21 -06:00
tvrrug/Round2	Followup to Ender config	2018-01-15 06:00:21 -06:00
UltiMachine/Archim2	Followup to Ender config	2018-01-15 06:00:21 -06:00
Velleman	Followup to Ender config	2018-01-15 06:00:21 -06:00
Wanhao/Duplicator 6	Followup to Ender config	2018-01-15 06:00:21 -06:00
wt150	Followup to Ender config	2018-01-15 06:00:21 -06:00