Marlin_Firmware/Marlin/pins_TEENSYLU.h
Dave Johnson 4718c09c48 Remove extraneous USBCON defines for AT90USB boards
USBCON is definied by serial.h pullikng in MarlinConfig.h which in turn pulls in Arduino.h.  Defining in later includes has shown to cause compile issues so removing all extraneous calls for and potentially easier future linker troubleshooting.
more USBCON unification
2017-07-23 16:41:48 -07:00

165 lines
5.2 KiB
C
Executable File

/**
* Marlin 3D Printer Firmware
* Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
*
* Based on Sprinter and grbl.
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <http://www.gnu.org/licenses/>.
*
*/
/**
* Rev C 2 JUN 2017
*
* Converted to Arduino pin numbering
*/
/**
* There are two Arduino IDE extensions that are compatible with this board
* and with the mainstream Marlin software. All have been used with Arduino 1.6.12
*
* Teensyduino - http://www.pjrc.com/teensy/teensyduino.html
* Select Teensy++ 2.0 in Arduino IDE from the 'Tools -> Boards' menu
*
* Installation instructions are at the above URL. Don't bother loading the
* libraries - they are not used with the Marlin software.
*
* Printrboard - https://github.com/scwimbush/Printrboard-HID-Arduino-IDE-Support
* This is basically Teensyduino but with a bootloader that can handle image sizes
* larger than 64K.
*
* Installation:
*
* 1. Go to the above URL, click on the "Clone or Download" button and then
* click on "Download ZIP" button.
* 2. Unzip the file, find the "printrboard" directory and then copy it to the
* hardware directory in Arduino. The Arduino hardware directory will probably
* be located in a path similar to this: C:\Program Files (x86)\Arduino\hardware.
* 3. Restart Arduino.
* 4. Select "Printrboard" from the 'Tools -> Boards' menu.
*
* Teensyduino is the most popular option. Printrboard is used if your board doesn't have
* the Teensyduino bootloader on it.
*/
/**
* To burn the bootloader that comes with Printrboard:
*
* 1. Connect your programmer to the board.
* 2. In the Arduino IDE select "Printrboard" and then select the programmer.
* 3. In the Arduino IDE click on "burn bootloader". Don't worry about the "verify failed at 1F000" error message.
* 4. The programmer is no longer needed. Remove it.
*/
/**
* SILKSCREEN ERROR
*
* The silkscreen for the endstops do NOT match the schematic. The silkscreen SHOULD
* read (from left to right) X-STOP, Y-STOP, Z-STOP & E-STOP. The silkscreen actually
* reads E-STOP, X-STOP, Y-STOP & Z-STOP.
*
* The pin assignments in this file match the silkscreen.
*/
#if !defined(__AVR_AT90USB1286__) && !defined(__AVR_AT90USB1286P__)
#error "Oops! Make sure you have 'Teensy++ 2.0' or 'Printrboard' selected from the 'Tools -> Boards' menu."
#endif
#define BOARD_NAME "Teensylu"
#define LARGE_FLASH true
//
// Limit Switch definitions that match the SCHEMATIC
//
//#define X_STOP_PIN 25 // B5
//#define Y_STOP_PIN 26 // B6
//#define Z_STOP_PIN 27 // B7
//#define E_STOP_PIN 36 // E4
//
// Limit Switch definitions that match the SILKSCREEN
//
#define X_STOP_PIN 26 // B6
#define Y_STOP_PIN 27 // B7
#define Z_STOP_PIN 36 // E4
//#define E_STOP_PIN 25 // B5
//
// Steppers
//
#define X_STEP_PIN 28 // A0
#define X_DIR_PIN 29 // A1
#define X_ENABLE_PIN 19 // E7
#define Y_STEP_PIN 30 // A2
#define Y_DIR_PIN 31 // A3
#define Y_ENABLE_PIN 18 // E6
#define Z_STEP_PIN 32 // A4
#define Z_DIR_PIN 33 // A5
#define Z_ENABLE_PIN 17 // C7
#define E0_STEP_PIN 34 // A6
#define E0_DIR_PIN 35 // A7
#define E0_ENABLE_PIN 13 // C3
//
// Temperature Sensors
//
#define TEMP_0_PIN 7 // Analog Input (Extruder)
#define TEMP_BED_PIN 6 // Analog Input (Bed)
//
// Heaters / Fans
//
#define HEATER_0_PIN 15 // C5 PWM3B - Extruder
#define HEATER_BED_PIN 14 // C4 PWM3C
#define FAN_PIN 16 // C6 PWM3A
//
// Misc. Functions
//
#define SDSS 20 // B0 JP31-6
#define CASE_LIGHT_PIN 0 // D0 IO-14 PWM0B
//
// LCD / Controller
//
#if ENABLED(ULTRA_LCD) && ENABLED(NEWPANEL)
#define BEEPER_PIN -1
#if ENABLED(LCD_I2C_PANELOLU2)
#define BTN_EN1 3 // D3 IO-8
#define BTN_EN2 2 // D2 IO-10
#define BTN_ENC 41 // F3 IO-7
#define SDSS 38 // F0 IO-13 use SD card on Panelolu2
#endif
#define SD_DETECT_PIN -1
#endif // ULTRA_LCD && NEWPANEL
//
// M3/M4/M5 - Spindle/Laser Control
//
#define SPINDLE_LASER_PWM_PIN 24 // B4 IO-3 PWM2A - MUST BE HARDWARE PWM
#define SPINDLE_LASER_ENABLE_PIN 39 // F1 IO-11 - Pin should have a pullup!
#define SPINDLE_DIR_PIN 40 // F2 IO-9