Marlin_Firmware/Marlin/pins_RIGIDBOARD.h
2016-08-02 20:31:44 -07:00

118 lines
2.9 KiB
C

/**
* Marlin 3D Printer Firmware
* Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
*
* Based on Sprinter and grbl.
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <http://www.gnu.org/licenses/>.
*
*/
/**
* RIGIDBOARD Arduino Mega with RAMPS v1.4 pin assignments
*/
#define BOARD_NAME "RigidBoard"
#define RAMPS_D10_PIN 9 // EXTRUDER 1
#define MOSFET_D_PIN 12 // EXTRUDER 2 or FAN
#ifndef Z_MIN_PROBE_PIN
#define Z_MIN_PROBE_PIN 19 // Z-MAX pin J14 End Stops
#endif
#include "pins_RAMPS.h"
#undef TEMP_0_PIN
#undef TEMP_1_PIN
#define TEMP_0_PIN 14 // ANALOG NUMBERING
#define TEMP_1_PIN 13 // ANALOG NUMBERING
// LCD Panel options for the RigidBoard
#if ENABLED(RIGIDBOT_PANEL)
#undef BEEPER_PIN
#define BEEPER_PIN -1
// Direction buttons
#define BTN_UP 37
#define BTN_DWN 35
#define BTN_LFT 33
#define BTN_RT 32
// 'R' button
#undef BTN_ENC
#define BTN_ENC 31
// Disable encoder
#undef BTN_EN1
#define BTN_EN1 -1
#undef BTN_EN2
#define BTN_EN2 -1
#undef SD_DETECT_PIN
#define SD_DETECT_PIN 22
#elif ENABLED(REPRAP_DISCOUNT_SMART_CONTROLLER)
#undef BEEPER_PIN
#define BEEPER_PIN -1
#undef SD_DETECT_PIN
#define SD_DETECT_PIN 22
#undef KILL_PIN
#define KILL_PIN 32
#endif
// SPI for Max6675 or Max31855 Thermocouple
#undef MAX6675_SS
#if ENABLED(SDSUPPORT)
#define MAX6675_SS 49 // Don't use pin 49 as this is tied to the switch inside the SD card socket to detect if there is an SD card present
#else
#define MAX6675_SS 53 // Don't use pin 53 if there is even the remote possibility of using Display/SD card
#endif
// RigidBot swaps E0 / E1 plugs vs RAMPS 1.3
#undef E0_STEP_PIN
#undef E0_DIR_PIN
#undef E0_ENABLE_PIN
#define E0_STEP_PIN 36
#define E0_DIR_PIN 34
#define E0_ENABLE_PIN 30
#undef E1_STEP_PIN
#undef E1_DIR_PIN
#undef E1_ENABLE_PIN
#define E1_STEP_PIN 26
#define E1_DIR_PIN 28
#define E1_ENABLE_PIN 24
#undef FAN_PIN
#define FAN_PIN 8 // Same as RAMPS_13_EEF
#undef PS_ON_PIN
#define PS_ON_PIN -1
#undef HEATER_BED_PIN
#define HEATER_BED_PIN 10
#undef TEMP_BED_PIN
#define TEMP_BED_PIN 15 // ANALOG NUMBERING
#define STEPPER_RESET_PIN 41 // Stepper drivers have a reset on RigidBot