Marlin_Firmware/Marlin/src/HAL/HAL_STM32F7
2018-10-23 22:35:44 -05:00
..
EEPROM_Emul Adjust some HAL formatting 2018-09-30 21:24:37 -05:00
EmulatedEeprom.cpp Use uint8_t in EEPROM code 2018-10-09 19:00:01 -05:00
endstop_interrupts.h Add support for Triple-Z steppers/endstops 2018-09-16 00:35:58 -05:00
fastio_STM32F7.h Correct PWM_PIN behavior for STM32 HALs (#12027) 2018-10-07 17:08:01 -05:00
HAL_Servo_STM32F7.cpp delay(SERVO_DELAY) => safe_delay(servo_delay[servo_index]) 2018-05-28 03:44:32 -05:00
HAL_Servo_STM32F7.h Add support for STM32F7 MCU 2018-01-15 01:13:03 -06:00
HAL_spi_STM32F7.cpp Updates to STM32F7 HAL, for completeness (#11770) 2018-09-09 03:26:15 -05:00
HAL_timers_STM32F7.cpp Updates to STM32F7 HAL, for completeness (#11770) 2018-09-09 03:26:15 -05:00
HAL_timers_STM32F7.h Updates to STM32F7 HAL, for completeness (#11770) 2018-09-09 03:26:15 -05:00
HAL.cpp Use a macro for HAL header redirection (#10380) 2018-04-12 20:25:08 -05:00
HAL.h Use uint8_t in EEPROM code 2018-10-09 19:00:01 -05:00
persistent_store_eeprom.cpp Use uint8_t in EEPROM code 2018-10-09 19:00:01 -05:00
pinsDebug.h Use a macro for HAL header redirection (#10380) 2018-04-12 20:25:08 -05:00
README.md Clean up trailing whitespace 2018-01-21 17:19:38 -06:00
SanityCheck.h Code changes supporting up to 6 extruders 2018-09-16 22:32:53 -05:00
spi_pins.h Fix some comment formatting 2018-10-23 22:35:44 -05:00
TMC2660.cpp Corrections for dylsexic TMC 2018-09-29 18:51:11 -05:00
TMC2660.h Corrections for dylsexic TMC 2018-09-29 18:51:11 -05:00
watchdog_STM32F7.cpp Cleanups for STM32F7 2018-01-15 02:46:37 -06:00
watchdog_STM32F7.h Fix some header comments 2018-07-17 19:50:24 -05:00

This HAL is for the STM32F765 board "The Borg" used with STM32Generic Arduino core by danieleff.

Original core is located at:

https://github.com/danieleff/STM32GENERIC

but i have not committed the changes needed for the Borg there yet, so please use:

https://github.com/Spawn32/STM32GENERIC

Unzip it into [Arduino]/hardware folder

Download the latest GNU ARM Embedded Toolchain:

https://developer.arm.com/open-source/gnu-toolchain/gnu-rm/downloads

(The one in Arduino dosen't support STM32F7).

Change compiler.path in platform.txt to point to that you downloaded.

This HAL is in development.

Currently only tested on "The Borg".

You will also need the latest Arduino 1.9.0-beta or newer.

This HAL is a modified version of Chris Barr's Picoprint STM32F4 HAL, so shouldn't be to hard to get it to work on a F4.