257 lines
5.9 KiB
C
257 lines
5.9 KiB
C
/**
|
|
* Marlin 3D Printer Firmware
|
|
* Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
|
|
*
|
|
* Based on Sprinter and grbl.
|
|
* Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
|
|
*
|
|
* This program is free software: you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License as published by
|
|
* the Free Software Foundation, either version 3 of the License, or
|
|
* (at your option) any later version.
|
|
*
|
|
* This program is distributed in the hope that it will be useful,
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
* GNU General Public License for more details.
|
|
*
|
|
* You should have received a copy of the GNU General Public License
|
|
* along with this program. If not, see <http://www.gnu.org/licenses/>.
|
|
*
|
|
*/
|
|
#pragma once
|
|
|
|
#ifndef STM32F4
|
|
#error "Oops! Select an STM32F4 board in 'Tools > Board.'"
|
|
#elif HOTENDS > 3 || E_STEPPERS > 3
|
|
#error "RUMBA32 supports up to 3 hotends / E-steppers."
|
|
#endif
|
|
|
|
#ifndef BOARD_INFO_NAME
|
|
#define BOARD_INFO_NAME "FYSETC_S6"
|
|
#endif
|
|
#ifndef DEFAULT_MACHINE_NAME
|
|
#define DEFAULT_MACHINE_NAME BOARD_INFO_NAME
|
|
#endif
|
|
|
|
// change the prio to 3 , 2 is for software serial
|
|
//#define TEMP_TIMER_IRQ_PRIO 3
|
|
|
|
//
|
|
// EEPROM Emulation
|
|
//
|
|
#define FLASH_EEPROM_EMULATION
|
|
//#define SRAM_EEPROM_EMULATION
|
|
//#define I2C_EEPROM
|
|
#ifdef I2C_EEPROM
|
|
#undef E2END // Defined in Arduino Core STM32 to be used with EEPROM emulation. This board uses a real EEPROM.
|
|
#define E2END 0xFFF // 4KB
|
|
#endif
|
|
|
|
//
|
|
// Limit Switches
|
|
//
|
|
#define X_MIN_PIN PB14
|
|
#define X_MAX_PIN PA1
|
|
#define Y_MIN_PIN PB13
|
|
#define Y_MAX_PIN PA2
|
|
#define Z_MIN_PIN PA0
|
|
#define Z_MAX_PIN PA3
|
|
|
|
//
|
|
// Servos
|
|
// share with Z_MAX_PIN
|
|
//
|
|
#define SERVO0_PIN PA3
|
|
|
|
//
|
|
// Steppers
|
|
//
|
|
#define X_STEP_PIN PE11
|
|
#define X_DIR_PIN PE10
|
|
#define X_ENABLE_PIN PE12
|
|
#define X_CS_PIN PE7
|
|
|
|
#define Y_STEP_PIN PD8
|
|
#define Y_DIR_PIN PB12
|
|
#define Y_ENABLE_PIN PD9
|
|
#define Y_CS_PIN PE15
|
|
|
|
#define Z_STEP_PIN PD14
|
|
#define Z_DIR_PIN PD13
|
|
#define Z_ENABLE_PIN PD15
|
|
#define Z_CS_PIN PD10
|
|
|
|
#define E0_STEP_PIN PD5
|
|
#define E0_DIR_PIN PD6
|
|
#define E0_ENABLE_PIN PD4
|
|
#define E0_CS_PIN PD7
|
|
|
|
#define E1_STEP_PIN PE6
|
|
#define E1_DIR_PIN PC13
|
|
#define E1_ENABLE_PIN PE5
|
|
#define E1_CS_PIN PC14
|
|
|
|
#define E2_STEP_PIN PE2
|
|
#define E2_DIR_PIN PE4
|
|
#define E2_ENABLE_PIN PE3
|
|
#define E2_CS_PIN PC15
|
|
|
|
#if HAS_TMC220x
|
|
//
|
|
// TMC2208/TMC2209 stepper drivers
|
|
//
|
|
|
|
//
|
|
// Software serial
|
|
//
|
|
#define X_SERIAL_TX_PIN PE9
|
|
#define X_SERIAL_RX_PIN PE8
|
|
|
|
#define Y_SERIAL_TX_PIN PE14
|
|
#define Y_SERIAL_RX_PIN PE13
|
|
|
|
#define Z_SERIAL_TX_PIN PD11
|
|
#define Z_SERIAL_RX_PIN PD12
|
|
|
|
#define E0_SERIAL_TX_PIN PD3
|
|
#define E0_SERIAL_RX_PIN PA15
|
|
|
|
#define E1_SERIAL_TX_PIN PC4
|
|
#define E1_SERIAL_RX_PIN PC5
|
|
|
|
#define E2_SERIAL_TX_PIN PE1
|
|
#define E2_SERIAL_RX_PIN PE0
|
|
#endif
|
|
|
|
//
|
|
// Temperature Sensors
|
|
//
|
|
#define TEMP_0_PIN PC0
|
|
#define TEMP_1_PIN PC1
|
|
#define TEMP_2_PIN PC2
|
|
#define TEMP_BED_PIN PC3
|
|
|
|
//
|
|
// Heaters / Fans
|
|
//
|
|
#define HEATER_0_PIN PB3
|
|
#define HEATER_1_PIN PB4
|
|
#define HEATER_2_PIN PB15
|
|
#define HEATER_BED_PIN PC8
|
|
|
|
#define FAN_PIN PB0
|
|
#define FAN1_PIN PB1
|
|
#define FAN2_PIN PB2
|
|
|
|
//
|
|
// SPI
|
|
//
|
|
#define SCK_PIN PA5
|
|
#define MISO_PIN PA6
|
|
#define MOSI_PIN PA7
|
|
|
|
//
|
|
// Misc. Functions
|
|
//
|
|
//#define LED_PIN PB14
|
|
//#define BTN_PIN PC10
|
|
//#define PS_ON_PIN PE11
|
|
//#define KILL_PIN PC5
|
|
|
|
#define SDSS PA4
|
|
|
|
//
|
|
// LCD / Controller
|
|
//
|
|
#if HAS_SPI_LCD
|
|
#define BEEPER_PIN PC9
|
|
#define BTN_ENC PA8
|
|
|
|
#if ENABLED(CR10_STOCKDISPLAY)
|
|
#define LCD_PINS_RS PD0
|
|
|
|
#define BTN_EN1 PC11
|
|
#define BTN_EN2 PC10
|
|
|
|
#define LCD_PINS_ENABLE PD1
|
|
#define LCD_PINS_D4 PC12
|
|
|
|
// CR10_Stock Display needs a different delay setting on SKR PRO v1.1, so undef it here.
|
|
// It will be defined again at the #HAS_GRAPHICAL_LCD section below.
|
|
#undef ST7920_DELAY_1
|
|
#undef ST7920_DELAY_2
|
|
#undef ST7920_DELAY_3
|
|
|
|
#else
|
|
|
|
#define LCD_PINS_RS PD2
|
|
|
|
#define BTN_EN1 PC6
|
|
#define BTN_EN2 PC7
|
|
#define SD_DETECT_PIN PB10
|
|
|
|
#define LCD_SDSS PA4
|
|
|
|
#define LCD_PINS_ENABLE PC11
|
|
#define LCD_PINS_D4 PC10
|
|
|
|
#if ENABLED(FYSETC_MINI_12864)
|
|
// See https://wiki.fysetc.com/Mini12864_Panel
|
|
#define DOGLCD_CS PC11
|
|
#define DOGLCD_A0 PD2
|
|
#if ENABLED(FYSETC_GENERIC_12864_1_1)
|
|
#define LCD_BACKLIGHT_PIN PD0
|
|
#endif
|
|
#define LCD_RESET_PIN PC10 // Must be high or open for LCD to operate normally.
|
|
#if EITHER(FYSETC_MINI_12864_1_2, FYSETC_MINI_12864_2_0)
|
|
#ifndef RGB_LED_R_PIN
|
|
#define RGB_LED_R_PIN PC12
|
|
#endif
|
|
#ifndef RGB_LED_G_PIN
|
|
#define RGB_LED_G_PIN PD0
|
|
#endif
|
|
#ifndef RGB_LED_B_PIN
|
|
#define RGB_LED_B_PIN PD1
|
|
#endif
|
|
#elif ENABLED(FYSETC_MINI_12864_2_1)
|
|
#define NEOPIXEL_PIN PC12
|
|
#endif
|
|
#endif // !FYSETC_MINI_12864
|
|
|
|
#if ENABLED(ULTIPANEL)
|
|
#define LCD_PINS_D5 PC12
|
|
#define LCD_PINS_D6 PD0
|
|
#define LCD_PINS_D7 PD1
|
|
#endif
|
|
|
|
#endif
|
|
|
|
// Alter timing for graphical display
|
|
#if HAS_GRAPHICAL_LCD
|
|
#ifndef ST7920_DELAY_1
|
|
#define ST7920_DELAY_1 DELAY_NS(96)
|
|
#endif
|
|
#ifndef ST7920_DELAY_2
|
|
#define ST7920_DELAY_2 DELAY_NS(48)
|
|
#endif
|
|
#ifndef ST7920_DELAY_3
|
|
#define ST7920_DELAY_3 DELAY_NS(600)
|
|
#endif
|
|
#endif
|
|
|
|
#endif // HAS_SPI_LCD
|
|
|
|
#ifndef RGB_LED_R_PIN
|
|
#define RGB_LED_R_PIN PB6
|
|
#endif
|
|
#ifndef RGB_LED_G_PIN
|
|
#define RGB_LED_G_PIN PB5
|
|
#endif
|
|
#ifndef RGB_LED_B_PIN
|
|
#define RGB_LED_B_PIN PB7
|
|
#endif
|
|
#ifndef RGB_LED_W_PIN
|
|
#define RGB_LED_W_PIN -1
|
|
#endif
|