Marlin_Firmware/Marlin/pins_LEAPFROG.h
esenapaj f41c60d4a4 Follow-up the PR #4955, etc
・More ANALOG NUMBERING to Analog Input
・Add comment header to all the section of all the pins files

・Sort sections as follows:
1. Some special definitions (USBCON, LARGE_FLASH, etc)
2. Servos
3. Limit Switches
4. Z Probe
5. Steppers
6. Temperature Sensors
7. Heaters / Fans
8. Misc. Functions
9. LCD / Controller

・Move MAX6675_SS into "Temperature Sensors" section
・Adjust spacing
2016-10-10 14:22:43 +09:00

92 lines
2.5 KiB
C

/**
* Marlin 3D Printer Firmware
* Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
*
* Based on Sprinter and grbl.
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <http://www.gnu.org/licenses/>.
*
*/
/**
* Leapfrog Driver board pin assignments
*/
#if !defined(__AVR_ATmega1280__) && !defined(__AVR_ATmega2560__)
#error "Oops! Make sure you have 'Arduino Mega' selected from the 'Tools -> Boards' menu."
#endif
#define BOARD_NAME "Leapfrog"
//
// Limit Switches
//
#define X_MIN_PIN 47
#define X_MAX_PIN 2
#define Y_MIN_PIN 48
#define Y_MAX_PIN 15
#define Z_MIN_PIN 49
#define Z_MAX_PIN -1
//
// Steppers
//
#define X_STEP_PIN 28
#define X_DIR_PIN 63
#define X_ENABLE_PIN 29
#define Y_STEP_PIN 14 // A6
#define Y_DIR_PIN 15 // A0
#define Y_ENABLE_PIN 39
#define Z_STEP_PIN 31 // A2
#define Z_DIR_PIN 32 // A6
#define Z_ENABLE_PIN 30 // A1
#define E0_STEP_PIN 34 // 34
#define E0_DIR_PIN 35 // 35
#define E0_ENABLE_PIN 33 // 33
#define E1_STEP_PIN 37 // 37
#define E1_DIR_PIN 40 // 40
#define E1_ENABLE_PIN 36 // 36
//
// Temperature Sensors
//
#define TEMP_0_PIN 13 // Analog Input (D27)
#define TEMP_1_PIN 15 // Analog Input (1)
#define TEMP_BED_PIN 14 // Analog Input (1,2 or I2C)
//
// Heaters / Fans
//
#define HEATER_0_PIN 9
#define HEATER_1_PIN 8 // 12
#define HEATER_2_PIN 11 // 13
#define HEATER_BED_PIN 10 // 14/15
#define FAN_PIN 7
//
// Misc. Functions
//
#define SDSS 11
#define LED_PIN 13
#define SOL1_PIN 16
#define SOL2_PIN 17
/* Unused (1) (2) (3) 4 5 6 7 8 9 10 11 12 13 (14) (15) (16) 17 (18) (19) (20) (21) (22) (23) 24 (25) (26) (27) 28 (29) (30) (31) */