Marlin_Firmware/Marlin/pins_BRAINWAVE.h
Dave Johnson 4718c09c48 Remove extraneous USBCON defines for AT90USB boards
USBCON is definied by serial.h pullikng in MarlinConfig.h which in turn pulls in Arduino.h.  Defining in later includes has shown to cause compile issues so removing all extraneous calls for and potentially easier future linker troubleshooting.
more USBCON unification
2017-07-23 16:41:48 -07:00

124 lines
3.7 KiB
C
Executable File

/**
* Marlin 3D Printer Firmware
* Copyright (C) 2017 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
*
* Based on Sprinter and grbl.
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <http://www.gnu.org/licenses/>.
*
*/
/**
* Brainwave 1.0 pin assignments (AT90USB646)
*
* Requires hardware bundle for Arduino:
* https://github.com/unrepentantgeek/brainwave-arduino
*/
/**
* Rev B 16 JAN 2017
*
* Added pointer to a currently available Arduino IDE extension that will
* allow this board to use the latest Marlin software
*/
/**
* Rev C 2 JUN 2017
*
* Converted to Arduino pin numbering
*/
/**
* Marlin_AT90USB - https://github.com/Bob-the-Kuhn/Marlin_AT90USB
* This is the only known IDE extension that is compatible with the pin definitions
* in this file, Adrduino 1.6.12 and the latest mainstream Marlin software.
*
* "Marlin_AT90USB" makes PWM0A available rather than the usual PWM1C. These PWMs share
* the same physical pin. Marlin uses TIMER1 to generate interrupts and sets it up such
* that PWM1A, PWM1B & PWM1C can't be used.
*
* Installation:
*
* 1. In the Arduino IDE, under Files -> Preferences paste the following URL
* https://rawgit.com/Bob-the-Kuhn/Marlin_AT90USB/master/package_MARLIN_AT90USB_index.json
* 2. Under Tools -> Board -> Boards manager, scroll to the bottom, click on MARLIN_AT90USB
* and then click on "Install"
* 3. Select "AT90USB646_TEENSYPP" from the 'Tools -> Boards' menu.
*/
/**
* To burn the bootloader that comes with Marlin_AT90USB:
*
* 1. Connect your programmer to the board.
* 2. In Arduino IDE select "AT90USB646_TEENSYPP" and then select the programmer.
* 3. In Arduino IDE click on "burn bootloader". Don't worry about the "verify failed at 1F000" error message.
* 4. The programmer is no longer needed. Remove it.
*/
#ifndef __AVR_AT90USB646__
#error "Oops! Make sure you have 'AT90USB646_TEENSYPP' selected from the 'Tools -> Boards' menu."
#endif
#define BOARD_NAME "Brainwave"
//
// Limit Switches
//
#define X_STOP_PIN 35 // A7
#define Y_STOP_PIN 34 // A6
#define Z_STOP_PIN 33 // A5
//
// Steppers
//
#define X_STEP_PIN 3 // D3
#define X_DIR_PIN 5 // D5
#define X_ENABLE_PIN 4 // D4
#define X_ATT_PIN 2 // D2
#define Y_STEP_PIN 7 // D7
#define Y_DIR_PIN 9 // E1
#define Y_ENABLE_PIN 8 // E0
#define Y_ATT_PIN 6 // D6
#define Z_STEP_PIN 11 // C1
#define Z_DIR_PIN 13 // C3
#define Z_ENABLE_PIN 12 // C2
#define Z_ATT_PIN 10 // C0
#define E0_STEP_PIN 15 // C5
#define E0_DIR_PIN 17 // C7
#define E0_ENABLE_PIN 16 // C6
#define E0_ATT_PIN 14 // C4
//
// Temperature Sensors
//
#define TEMP_0_PIN 7 // F7 Analog Input
#define TEMP_BED_PIN 6 // F6 Analog Input
//
// Heaters / Fans
//
#define HEATER_0_PIN 32 // A4 Extruder
#define HEATER_BED_PIN 18 // E6 Bed
#define FAN_PIN 31 // A3 Fan
//
// Misc. Functions
//
#define LED_PIN 19 // E7