127 lines
3.7 KiB
C
127 lines
3.7 KiB
C
/**
|
|
* Marlin 3D Printer Firmware
|
|
* Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
|
|
*
|
|
* Based on Sprinter and grbl.
|
|
* Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
|
|
*
|
|
* This program is free software: you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License as published by
|
|
* the Free Software Foundation, either version 3 of the License, or
|
|
* (at your option) any later version.
|
|
*
|
|
* This program is distributed in the hope that it will be useful,
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
* GNU General Public License for more details.
|
|
*
|
|
* You should have received a copy of the GNU General Public License
|
|
* along with this program. If not, see <https://www.gnu.org/licenses/>.
|
|
*
|
|
*/
|
|
#pragma once
|
|
|
|
/**
|
|
* FYSETC E4 pin assignments
|
|
* FYSETC E4 is a 3D printer control board based on the ESP32 microcontroller.
|
|
* Supports 4 stepper drivers, heated bed, single hotend.
|
|
*/
|
|
|
|
#include "env_validate.h"
|
|
|
|
#if EXTRUDERS > 1 || E_STEPPERS > 1
|
|
#error "FYSETC E4 only supports one E Stepper. Comment out this line to continue."
|
|
#elif HOTENDS > 1
|
|
#error "FYSETC E4 only supports one hotend / E-stepper. Comment out this line to continue."
|
|
#endif
|
|
|
|
#define BOARD_INFO_NAME "FYSETC_E4"
|
|
#define DEFAULT_MACHINE_NAME BOARD_INFO_NAME
|
|
|
|
//
|
|
// Disable I2S stepper stream
|
|
//
|
|
#undef I2S_STEPPER_STREAM
|
|
#define I2S_WS -1
|
|
#define I2S_BCK -1
|
|
#define I2S_DATA -1
|
|
|
|
//
|
|
// Limit Switches
|
|
//
|
|
#define X_STOP_PIN 34
|
|
#define Y_STOP_PIN 35
|
|
#define Z_STOP_PIN 15
|
|
|
|
//
|
|
// Steppers
|
|
//
|
|
#define X_STEP_PIN 27
|
|
#define X_DIR_PIN 26
|
|
#define X_ENABLE_PIN 25
|
|
|
|
#define Y_STEP_PIN 33
|
|
#define Y_DIR_PIN 32
|
|
#define Y_ENABLE_PIN X_ENABLE_PIN
|
|
|
|
#define Z_STEP_PIN 14
|
|
#define Z_DIR_PIN 12
|
|
#define Z_ENABLE_PIN X_ENABLE_PIN
|
|
|
|
#define E0_STEP_PIN 16
|
|
#define E0_DIR_PIN 17
|
|
#define E0_ENABLE_PIN X_ENABLE_PIN
|
|
|
|
#if HAS_TMC_UART
|
|
//
|
|
// TMC2209 stepper drivers
|
|
//
|
|
|
|
//
|
|
// Hardware serial 1
|
|
//
|
|
#define X_HARDWARE_SERIAL Serial1
|
|
#define Y_HARDWARE_SERIAL Serial1
|
|
#define Z_HARDWARE_SERIAL Serial1
|
|
#define E0_HARDWARE_SERIAL Serial1
|
|
|
|
#define TMC_BAUD_RATE 115200
|
|
#endif
|
|
|
|
//
|
|
// Temperature Sensors
|
|
//
|
|
#define TEMP_0_PIN 36 // Analog Input
|
|
#define TEMP_BED_PIN 39 // Analog Input
|
|
|
|
//
|
|
// Heaters / Fans
|
|
//
|
|
#define HEATER_0_PIN 2
|
|
#define FAN_PIN 13
|
|
#define HEATER_BED_PIN 4
|
|
|
|
//
|
|
// MicroSD card
|
|
//
|
|
#define SD_MOSI_PIN 23
|
|
#define SD_MISO_PIN 19
|
|
#define SD_SCK_PIN 18
|
|
#define SDSS 5
|
|
#define USES_SHARED_SPI // SPI is shared by SD card with TMC SPI drivers
|
|
|
|
/**
|
|
* Hardware serial pins
|
|
*
|
|
* Override these pins in Configuration.h or Configuration_adv.h if needed.
|
|
*
|
|
* Note: Serial2 can be defined using HARDWARE_SERIAL2_RX and HARDWARE_SERIAL2_TX
|
|
* but MRR ESPA does not have enough spare pins for such reassignment.
|
|
*/
|
|
#ifndef HARDWARE_SERIAL1_RX
|
|
#define HARDWARE_SERIAL1_RX 21
|
|
#endif
|
|
#ifndef HARDWARE_SERIAL1_TX
|
|
#define HARDWARE_SERIAL1_TX 22
|
|
#endif
|