234 lines
7.7 KiB
C
234 lines
7.7 KiB
C
/**
|
|
* Marlin 3D Printer Firmware
|
|
* Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
|
|
*
|
|
* Based on Sprinter and grbl.
|
|
* Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
|
|
*
|
|
* This program is free software: you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License as published by
|
|
* the Free Software Foundation, either version 3 of the License, or
|
|
* (at your option) any later version.
|
|
*
|
|
* This program is distributed in the hope that it will be useful,
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
* GNU General Public License for more details.
|
|
*
|
|
* You should have received a copy of the GNU General Public License
|
|
* along with this program. If not, see <http://www.gnu.org/licenses/>.
|
|
*
|
|
*/
|
|
#pragma once
|
|
|
|
/**
|
|
* 24 May 2018 - @chepo for STM32F103VET6
|
|
* Schematic: https://github.com/chepo92/Smartto/blob/master/circuit_diagram/Rostock301/Hardware_GTM32_PRO_VB.pdf
|
|
*/
|
|
|
|
#ifndef __STM32F1__
|
|
#error "Oops! Select an STM32F1 board in 'Tools > Board.'"
|
|
#endif
|
|
|
|
#define BOARD_INFO_NAME "GTM32 Pro VB"
|
|
#define DEFAULT_MACHINE_NAME "STM32F103VET6"
|
|
|
|
//#define DISABLE_DEBUG
|
|
|
|
//
|
|
// It is required to disable JTAG function because its pins are
|
|
// used as GPIO to drive the Y axis stepper.
|
|
// DO NOT ENABLE!
|
|
//
|
|
#define DISABLE_JTAG
|
|
|
|
//
|
|
// If you don't need the SWDIO functionality (any more), you may
|
|
// disable SWD here to regain PA13/PA14 pins for other use.
|
|
//
|
|
//#define DISABLE_JTAGSWD
|
|
|
|
// Ignore temp readings during development.
|
|
//#define BOGUS_TEMPERATURE_GRACE_PERIOD 2000
|
|
|
|
// Enable EEPROM Emulation for this board as it doesn't have EEPROM
|
|
#define FLASH_EEPROM_EMULATION
|
|
#define E2END 0xFFF // 4KB
|
|
|
|
//
|
|
// Limit Switches
|
|
//
|
|
#define X_MIN_PIN PE5 // ENDSTOPS 15,17
|
|
#define X_MAX_PIN PE4 // ENDSTOPS 16,18
|
|
#define Y_MIN_PIN PE3 // ENDSTOPS 9,11
|
|
#define Y_MAX_PIN PE2 // ENDSTOPS 10,12
|
|
#define Z_MIN_PIN PE1 // ENDSTOPS 3,5
|
|
#define Z_MAX_PIN PE0 // ENDSTOPS 4,6
|
|
|
|
//
|
|
// Steppers
|
|
//
|
|
#define X_STEP_PIN PC6
|
|
#define X_DIR_PIN PD13
|
|
#define X_ENABLE_PIN PA8
|
|
|
|
#define Y_STEP_PIN PA12
|
|
#define Y_DIR_PIN PA11
|
|
#define Y_ENABLE_PIN PA15
|
|
|
|
#define Z_STEP_PIN PD6
|
|
#define Z_DIR_PIN PD3
|
|
#define Z_ENABLE_PIN PB3
|
|
|
|
// Extruder stepper pins
|
|
// NOTE: Numbering here is made according to EXT connector numbers,
|
|
// the FANx_PWM line numbering in the schematics is reverse.
|
|
// That is, E0_*_PIN are the E2_* lines connected to E2_A1 step
|
|
// stick that drives the EXT0 output on the board.
|
|
//
|
|
#define E0_STEP_PIN PC14
|
|
#define E0_DIR_PIN PC13
|
|
#define E0_ENABLE_PIN PC15
|
|
|
|
#define E1_STEP_PIN PA0
|
|
#define E1_DIR_PIN PB6
|
|
#define E1_ENABLE_PIN PA1
|
|
|
|
#define E2_STEP_PIN PB2
|
|
#define E2_DIR_PIN PB11
|
|
#define E2_ENABLE_PIN PC4
|
|
|
|
//
|
|
// Heaters / Fans
|
|
//
|
|
#define HEATER_0_PIN PB0 // EXT0 port
|
|
#define HEATER_1_PIN PB5 // EXT1 port
|
|
#define HEATER_2_PIN PB4 // EXT2 port
|
|
#define HEATER_BED_PIN PB1 // CON2X3 hotbed port
|
|
|
|
//
|
|
// These are FAN PWM pins on EXT0..EXT2 connectors.
|
|
//
|
|
//#define FAN_PIN PB9 // EXT0 port
|
|
#define FAN1_PIN PB8 // EXT1 port
|
|
#define FAN2_PIN PB7 // EXT2 port
|
|
|
|
#ifndef E0_AUTO_FAN_PIN
|
|
#define E0_AUTO_FAN_PIN PB9 // EXT0 port, used as main extruder fan
|
|
#endif
|
|
|
|
//
|
|
// Temperature Sensors
|
|
//
|
|
#define TEMP_0_PIN PC2 // EXT0 port
|
|
#define TEMP_1_PIN PC1 // EXT1 port
|
|
#define TEMP_2_PIN PC0 // EXT2 port
|
|
#define TEMP_BED_PIN PC3 // CON2X3 hotbed port
|
|
|
|
//
|
|
// Misc. Functions
|
|
//
|
|
#define LED_PWM PD12 // External LED, pin 2 on LED labeled connector
|
|
|
|
//
|
|
// LCD / Controller
|
|
//
|
|
#if HAS_SPI_LCD
|
|
|
|
#if ENABLED(REPRAP_DISCOUNT_SMART_CONTROLLER)
|
|
//
|
|
// LCD display on J2 FFC40
|
|
// Geeetech's LCD2004A Control Panel is very much like
|
|
// RepRapDiscount Smart Controller, but adds an FFC40 connector
|
|
//
|
|
#define LCD_PINS_RS PE6 // CS chip select /SS chip slave select
|
|
#define LCD_PINS_ENABLE PE14 // SID (MOSI)
|
|
#define LCD_PINS_D4 PD8 // SCK (CLK) clock
|
|
#define LCD_PINS_D5 PD9
|
|
#define LCD_PINS_D6 PD10
|
|
#define LCD_PINS_D7 PE15
|
|
|
|
#else
|
|
//
|
|
// Serial LCDs can be implemented in ExtUI
|
|
//
|
|
//#define LCD_UART_TX PD8
|
|
//#define LCD_UART_RX PD9
|
|
#endif
|
|
|
|
#if HAS_GRAPHICAL_LCD
|
|
#define BOARD_ST7920_DELAY_1 DELAY_NS(96)
|
|
#define BOARD_ST7920_DELAY_2 DELAY_NS(48)
|
|
#define BOARD_ST7920_DELAY_3 DELAY_NS(715)
|
|
#endif
|
|
|
|
#endif // HAS_SPI_LCD
|
|
|
|
#if ENABLED(REPRAP_DISCOUNT_SMART_CONTROLLER)
|
|
//
|
|
// Geeetech's LCD2004A Control Panel is very much like
|
|
// RepRapDiscount Smart Controller, but adds an FFC40 connector
|
|
// connected with a flat wire to J2 connector on the board.
|
|
//
|
|
#define BTN_EN1 PE8
|
|
#define BTN_EN2 PE9
|
|
#define BTN_ENC PE13
|
|
|
|
#define GTM32_PRO_VB_USE_LCD_BEEPER
|
|
#define GTM32_PRO_VB_USE_EXT_SDCARD
|
|
#endif
|
|
|
|
//
|
|
// Beeper
|
|
//
|
|
#ifdef GTM32_PRO_VB_USE_LCD_BEEPER
|
|
// This is pin 32 on J2 FFC40 and pin, goes to the beeper
|
|
// on Geeetech's version of RepRapDiscount Smart Controller
|
|
// (e.g. on Rostock 301)
|
|
#define BEEPER_PIN PE12
|
|
#else
|
|
// This is the beeper on the board itself
|
|
#define BEEPER_PIN PB10
|
|
#endif
|
|
|
|
/**
|
|
* The on-board TF_CARD_SOCKET microSD card socket has no SD Detect pin wired.
|
|
*
|
|
* The FFC10 (SD_CARD) connector has the same pins as those routed to the FFC40 (J2)
|
|
* connector, which usually go to the SD Card slot on the Geeetech version of the
|
|
* RepRapDiscount Smart Controller. Both connectors have the card detect signal.
|
|
*
|
|
* The on-board SD card and the external card (on either SD_CARD or J2) are two
|
|
* separate devices and can work simultaneously. Unfortunately, Marlin only supports
|
|
* a single SPI Flash device (as of 2019-07-05) so only one is enabled here.
|
|
*/
|
|
#if ENABLED(GTM32_PRO_VB_USE_EXT_SDCARD)
|
|
//
|
|
// SD Card on RepRapDiscount Smart Controller (J2) or on SD_CARD connector
|
|
//
|
|
#define SS_PIN PC11
|
|
#define SCK_PIN PC12
|
|
#define MOSI_PIN PD2
|
|
#define MISO_PIN PC8
|
|
#define SD_DETECT_PIN PC7
|
|
#else
|
|
//
|
|
// Use the on-board card socket labeled TF_CARD_SOCKET
|
|
//
|
|
#define SS_PIN PA4
|
|
#define SCK_PIN PA5
|
|
#define MOSI_PIN PA7
|
|
#define MISO_PIN PA6
|
|
#define SD_DETECT_PIN -1 // Card detect is not connected
|
|
#endif
|
|
|
|
#define SDSS SS_PIN
|
|
|
|
//
|
|
// ESP WiFi can be soldered to J9 connector which is wired to USART2.
|
|
// Must define WIFISUPPORT in Configuration.h for the printer.
|
|
//
|
|
#define ESP_WIFI_MODULE_COM 2
|
|
#define ESP_WIFI_MODULE_BAUDRATE 115200
|
|
#define ESP_WIFI_MODULE_RESET_PIN -1
|