247 lines
7.6 KiB
C++
247 lines
7.6 KiB
C++
/**
|
|
* Marlin 3D Printer Firmware
|
|
* Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
|
|
*
|
|
* Based on Sprinter and grbl.
|
|
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
|
|
*
|
|
* This program is free software: you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License as published by
|
|
* the Free Software Foundation, either version 3 of the License, or
|
|
* (at your option) any later version.
|
|
*
|
|
* This program is distributed in the hope that it will be useful,
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
* GNU General Public License for more details.
|
|
*
|
|
* You should have received a copy of the GNU General Public License
|
|
* along with this program. If not, see <http://www.gnu.org/licenses/>.
|
|
*
|
|
*/
|
|
|
|
#include "../gcode.h"
|
|
#include "../../module/temperature.h"
|
|
#include "../../module/motion.h"
|
|
#include "../../module/planner.h"
|
|
#include "../../lcd/ultralcd.h"
|
|
#include "../../Marlin.h"
|
|
|
|
#if ENABLED(PRINTJOB_TIMER_AUTOSTART)
|
|
#include "../../module/printcounter.h"
|
|
#endif
|
|
|
|
#if ENABLED(PRINTER_EVENT_LEDS)
|
|
#include "../../feature/leds/leds.h"
|
|
#endif
|
|
|
|
/**
|
|
* M104: Set hot end temperature
|
|
*/
|
|
void GcodeSuite::M104() {
|
|
if (get_target_extruder_from_command()) return;
|
|
if (DEBUGGING(DRYRUN)) return;
|
|
|
|
const uint8_t e = target_extruder;
|
|
|
|
#if ENABLED(SINGLENOZZLE)
|
|
if (e != active_extruder) return;
|
|
#endif
|
|
|
|
if (parser.seenval('S')) {
|
|
const int16_t temp = parser.value_celsius();
|
|
thermalManager.setTargetHotend(temp, e);
|
|
|
|
#if ENABLED(DUAL_X_CARRIAGE)
|
|
if (dual_x_carriage_mode == DXC_DUPLICATION_MODE && e == 0)
|
|
thermalManager.setTargetHotend(temp ? temp + duplicate_extruder_temp_offset : 0, 1);
|
|
#endif
|
|
|
|
#if ENABLED(PRINTJOB_TIMER_AUTOSTART)
|
|
/**
|
|
* Stop the timer at the end of print. Start is managed by 'heat and wait' M109.
|
|
* We use half EXTRUDE_MINTEMP here to allow nozzles to be put into hot
|
|
* standby mode, for instance in a dual extruder setup, without affecting
|
|
* the running print timer.
|
|
*/
|
|
if (temp <= (EXTRUDE_MINTEMP) / 2) {
|
|
print_job_timer.stop();
|
|
lcd_reset_status();
|
|
}
|
|
#endif
|
|
}
|
|
|
|
#if ENABLED(AUTOTEMP)
|
|
planner.autotemp_M104_M109();
|
|
#endif
|
|
}
|
|
|
|
/**
|
|
* M109: Sxxx Wait for extruder(s) to reach temperature. Waits only when heating.
|
|
* Rxxx Wait for extruder(s) to reach temperature. Waits when heating and cooling.
|
|
*/
|
|
|
|
#ifndef MIN_COOLING_SLOPE_DEG
|
|
#define MIN_COOLING_SLOPE_DEG 1.50
|
|
#endif
|
|
#ifndef MIN_COOLING_SLOPE_TIME
|
|
#define MIN_COOLING_SLOPE_TIME 60
|
|
#endif
|
|
|
|
void GcodeSuite::M109() {
|
|
|
|
if (get_target_extruder_from_command()) return;
|
|
if (DEBUGGING(DRYRUN)) return;
|
|
|
|
#if ENABLED(SINGLENOZZLE)
|
|
if (target_extruder != active_extruder) return;
|
|
#endif
|
|
|
|
const bool no_wait_for_cooling = parser.seenval('S');
|
|
if (no_wait_for_cooling || parser.seenval('R')) {
|
|
const int16_t temp = parser.value_celsius();
|
|
thermalManager.setTargetHotend(temp, target_extruder);
|
|
|
|
#if ENABLED(DUAL_X_CARRIAGE)
|
|
if (dual_x_carriage_mode == DXC_DUPLICATION_MODE && target_extruder == 0)
|
|
thermalManager.setTargetHotend(temp ? temp + duplicate_extruder_temp_offset : 0, 1);
|
|
#endif
|
|
|
|
#if ENABLED(PRINTJOB_TIMER_AUTOSTART)
|
|
/**
|
|
* Use half EXTRUDE_MINTEMP to allow nozzles to be put into hot
|
|
* standby mode, (e.g., in a dual extruder setup) without affecting
|
|
* the running print timer.
|
|
*/
|
|
if (parser.value_celsius() <= (EXTRUDE_MINTEMP) / 2) {
|
|
print_job_timer.stop();
|
|
lcd_reset_status();
|
|
}
|
|
else
|
|
print_job_timer.start();
|
|
#endif
|
|
|
|
#if ENABLED(ULTRA_LCD)
|
|
const bool heating = thermalManager.isHeatingHotend(target_extruder);
|
|
if (heating || !no_wait_for_cooling)
|
|
#if HOTENDS > 1
|
|
lcd_status_printf_P(0, heating ? PSTR("E%i " MSG_HEATING) : PSTR("E%i " MSG_COOLING), target_extruder + 1);
|
|
#else
|
|
lcd_setstatusPGM(heating ? PSTR("E " MSG_HEATING) : PSTR("E " MSG_COOLING));
|
|
#endif
|
|
#endif
|
|
}
|
|
else return;
|
|
|
|
#if ENABLED(AUTOTEMP)
|
|
planner.autotemp_M104_M109();
|
|
#endif
|
|
|
|
#if TEMP_RESIDENCY_TIME > 0
|
|
millis_t residency_start_ms = 0;
|
|
// Loop until the temperature has stabilized
|
|
#define TEMP_CONDITIONS (!residency_start_ms || PENDING(now, residency_start_ms + (TEMP_RESIDENCY_TIME) * 1000UL))
|
|
#else
|
|
// Loop until the temperature is very close target
|
|
#define TEMP_CONDITIONS (wants_to_cool ? thermalManager.isCoolingHotend(target_extruder) : thermalManager.isHeatingHotend(target_extruder))
|
|
#endif
|
|
|
|
float target_temp = -1.0, old_temp = 9999.0;
|
|
bool wants_to_cool = false;
|
|
wait_for_heatup = true;
|
|
millis_t now, next_temp_ms = 0, next_cool_check_ms = 0;
|
|
|
|
#if DISABLED(BUSY_WHILE_HEATING)
|
|
KEEPALIVE_STATE(NOT_BUSY);
|
|
#endif
|
|
|
|
#if ENABLED(PRINTER_EVENT_LEDS)
|
|
const float start_temp = thermalManager.degHotend(target_extruder);
|
|
uint8_t old_blue = 0;
|
|
#endif
|
|
|
|
do {
|
|
// Target temperature might be changed during the loop
|
|
if (target_temp != thermalManager.degTargetHotend(target_extruder)) {
|
|
wants_to_cool = thermalManager.isCoolingHotend(target_extruder);
|
|
target_temp = thermalManager.degTargetHotend(target_extruder);
|
|
|
|
// Exit if S<lower>, continue if S<higher>, R<lower>, or R<higher>
|
|
if (no_wait_for_cooling && wants_to_cool) break;
|
|
}
|
|
|
|
now = millis();
|
|
if (ELAPSED(now, next_temp_ms)) { //Print temp & remaining time every 1s while waiting
|
|
next_temp_ms = now + 1000UL;
|
|
thermalManager.print_heaterstates();
|
|
#if TEMP_RESIDENCY_TIME > 0
|
|
SERIAL_PROTOCOLPGM(" W:");
|
|
if (residency_start_ms)
|
|
SERIAL_PROTOCOL(long((((TEMP_RESIDENCY_TIME) * 1000UL) - (now - residency_start_ms)) / 1000UL));
|
|
else
|
|
SERIAL_PROTOCOLCHAR('?');
|
|
#endif
|
|
SERIAL_EOL();
|
|
}
|
|
|
|
idle();
|
|
reset_stepper_timeout(); // Keep steppers powered
|
|
|
|
const float temp = thermalManager.degHotend(target_extruder);
|
|
|
|
#if ENABLED(PRINTER_EVENT_LEDS)
|
|
// Gradually change LED strip from violet to red as nozzle heats up
|
|
if (!wants_to_cool) {
|
|
const uint8_t blue = map(constrain(temp, start_temp, target_temp), start_temp, target_temp, 255, 0);
|
|
if (blue != old_blue) {
|
|
old_blue = blue;
|
|
leds.set_color(
|
|
MakeLEDColor(255, 0, blue, 0, pixels.getBrightness())
|
|
#if ENABLED(NEOPIXEL_IS_SEQUENTIAL)
|
|
, true
|
|
#endif
|
|
);
|
|
}
|
|
}
|
|
#endif
|
|
|
|
#if TEMP_RESIDENCY_TIME > 0
|
|
|
|
const float temp_diff = ABS(target_temp - temp);
|
|
|
|
if (!residency_start_ms) {
|
|
// Start the TEMP_RESIDENCY_TIME timer when we reach target temp for the first time.
|
|
if (temp_diff < TEMP_WINDOW) residency_start_ms = now;
|
|
}
|
|
else if (temp_diff > TEMP_HYSTERESIS) {
|
|
// Restart the timer whenever the temperature falls outside the hysteresis.
|
|
residency_start_ms = now;
|
|
}
|
|
|
|
#endif
|
|
|
|
// Prevent a wait-forever situation if R is misused i.e. M109 R0
|
|
if (wants_to_cool) {
|
|
// break after MIN_COOLING_SLOPE_TIME seconds
|
|
// if the temperature did not drop at least MIN_COOLING_SLOPE_DEG
|
|
if (!next_cool_check_ms || ELAPSED(now, next_cool_check_ms)) {
|
|
if (old_temp - temp < float(MIN_COOLING_SLOPE_DEG)) break;
|
|
next_cool_check_ms = now + 1000UL * MIN_COOLING_SLOPE_TIME;
|
|
old_temp = temp;
|
|
}
|
|
}
|
|
|
|
} while (wait_for_heatup && TEMP_CONDITIONS);
|
|
|
|
if (wait_for_heatup) {
|
|
lcd_reset_status();
|
|
#if ENABLED(PRINTER_EVENT_LEDS)
|
|
leds.set_white();
|
|
#endif
|
|
}
|
|
|
|
#if DISABLED(BUSY_WHILE_HEATING)
|
|
KEEPALIVE_STATE(IN_HANDLER);
|
|
#endif
|
|
}
|