Marlin_Firmware/Marlin/pins_CNCONTROLS_11.h
esenapaj f41c60d4a4 Follow-up the PR #4955, etc
・More ANALOG NUMBERING to Analog Input
・Add comment header to all the section of all the pins files

・Sort sections as follows:
1. Some special definitions (USBCON, LARGE_FLASH, etc)
2. Servos
3. Limit Switches
4. Z Probe
5. Steppers
6. Temperature Sensors
7. Heaters / Fans
8. Misc. Functions
9. LCD / Controller

・Move MAX6675_SS into "Temperature Sensors" section
・Adjust spacing
2016-10-10 14:22:43 +09:00

118 lines
2.6 KiB
C

/**
* CartesioV11 pin assignments
*/
#if !defined(__AVR_ATmega1280__) && !defined(__AVR_ATmega2560__)
#error Oops! Make sure you have 'Arduino Mega' selected from the 'Tools -> Boards' menu.
#endif
#define BOARD_NAME "CN Controls V11"
//#define LARGE_FLASH true
//
// Limit Switches
//
#define X_STOP_PIN 43
#define Y_STOP_PIN 45
#define Z_STOP_PIN 42
//
// Steppers
//
#define X_STEP_PIN 34
#define X_DIR_PIN 36
#define X_ENABLE_PIN 35
#define Y_STEP_PIN 37
#define Y_DIR_PIN 39
#define Y_ENABLE_PIN 38
#define Z_STEP_PIN 40
#define Z_DIR_PIN 48
#define Z_ENABLE_PIN 41
#define E0_STEP_PIN 29
#define E0_DIR_PIN 28
#define E0_ENABLE_PIN 3
#define E1_STEP_PIN 61
#define E1_DIR_PIN 62
#define E1_ENABLE_PIN 60
#define E2_STEP_PIN 15
#define E2_DIR_PIN 14
#define E2_ENABLE_PIN 16
#define E3_STEP_PIN 44
#define E3_DIR_PIN 49
#define E3_ENABLE_PIN 47
//
// Temperature Sensors
//
#define TEMP_0_PIN 0 // Analog Input
#define TEMP_1_PIN 3 // Analog Input. 3 for tool2 -> 2 for chambertemp
#define TEMP_2_PIN 2 // Analog Input. 9 for tool3 -> 2 for chambertemp
#define TEMP_3_PIN 11 // Analog Input. 11 for tool4 -> 2 for chambertemp
#define TEMP_BED_PIN 1 // Analog Input
//#define TEMP_CHAMBER_PIN 2 // Analog Input
//
// Heaters / Fans
//
#define HEATER_0_PIN 5
#define HEATER_1_PIN 58
#define HEATER_2_PIN 64
#define HEATER_3_PIN 46
#define HEATER_BED_PIN 2
//#define FAN_PIN 7 // common PWM pin for all tools
//
// Misc. Functions
//
#define SDSS 53
#define SD_DETECT_PIN 13
// Tools
//#define TOOL_0_PIN 4
//#define TOOL_1_PIN 59
//#define TOOL_2_PIN 8
//#define TOOL_3_PIN 30
//#define TOOL_PWM_PIN 7 // common PWM pin for all tools
// Common I/O
//#define FIL_RUNOUT_PIN -1
//#define PWM_1_PIN 11
//#define PWM_2_PIN 10
//#define SPARE_IO 12
//
// LCD / Controller
//
#define BEEPER_PIN 6
// Pins for DOGM SPI LCD Support
#define DOGLCD_A0 26
#define DOGLCD_CS 24
#define DOGLCD_MOSI -1
#define DOGLCD_SCK -1
#define BTN_EN1 23
#define BTN_EN2 25
#define BTN_ENC 27
// Hardware buttons for manual movement of XYZ
#define SHIFT_OUT 19
#define SHIFT_LD 18
#define SHIFT_CLK 17
//#define UI1 31
//#define UI2 22
#define STAT_LED_BLUE_PIN -1
#define STAT_LED_RED_PIN 31