/**
 * Marlin 3D Printer Firmware
 * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
 *
 * Based on Sprinter and grbl.
 * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
 *
 * This program is free software: you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation, either version 3 of the License, or
 * (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program.  If not, see <https://www.gnu.org/licenses/>.
 *
 */
#pragma once

/**
 * Tenlog pin assignments
 */

#if NOT_TARGET(__AVR_ATmega2560__)
  #error "Oops! Select 'Arduino/Genuino Mega or Mega 2560' in 'Tools > Board.'"
#elif HOTENDS > 2 || E_STEPPERS > 2
  #error "Tenlog supports up to 2 hotends / E-steppers. Comment out this line to continue."
#endif

#define BOARD_INFO_NAME      "Tenlog D3 Hero"
#define DEFAULT_MACHINE_NAME BOARD_INFO_NAME

//
// Servos
//
#define SERVO0_PIN                            11
#define SERVO1_PIN                             6
#define SERVO2_PIN                            -1  // Original pin 5 used for hotend fans
#define SERVO3_PIN                             4

//
// Limit Switches
//
#define X_MIN_PIN                              3
#define X_MAX_PIN                              2
#define Y_MIN_PIN                             14
//#define Y_MAX_PIN                           15  // Connected to "DJ" plug on extruder heads
#define Z_MIN_PIN                             18
#define Z_MAX_PIN                             19

//
// Z Probe (when not Z_MIN_PIN)
//
#ifndef Z_MIN_PROBE_PIN
  #define Z_MIN_PROBE_PIN                     15  // Ramps is normally 32
#endif

//
// Steppers
//
#define X_STEP_PIN                            54
#define X_DIR_PIN                             55
#define X_ENABLE_PIN                          38
//#ifndef X_CS_PIN
  //#define X_CS_PIN                          53
//#endif

#define X2_STEP_PIN                           36
#define X2_DIR_PIN                            34
#define X2_ENABLE_PIN                         30
//#ifndef X2_CS_PIN
  //#define X2_CS_PIN                         53
//#endif

#define Y_STEP_PIN                            60
#define Y_DIR_PIN                             61
#define Y_ENABLE_PIN                          56
//#ifndef Y_CS_PIN
 //#define Y_CS_PIN                           49
//#endif

#define Z_STEP_PIN                            46
#define Z_DIR_PIN                             48
#define Z_ENABLE_PIN                          62
//#ifndef Z_CS_PIN
 //#define Z_CS_PIN                           40
//#endif

#define Z2_STEP_PIN                           65
#define Z2_DIR_PIN                            66
#define Z2_ENABLE_PIN                         64
//#ifndef Z2_CS_PIN
 //#define Z2_CS_PIN                          40
//#endif

#define E0_STEP_PIN                           26
#define E0_DIR_PIN                            28
#define E0_ENABLE_PIN                         24
//#ifndef E0_CS_PIN
  //define E0_CS_PIN                          42
//#endif

#define E1_STEP_PIN                           57
#define E1_DIR_PIN                            58
#define E1_ENABLE_PIN                         59
//#ifndef E1_CS_PIN
  //define E1_CS_PIN                          44
//#endif

//#define E2_STEP_PIN                         42
//#define E2_DIR_PIN                          43
//#define E2_ENABLE_PIN                       44

//
// Temperature Sensors
//
#define TEMP_0_PIN                            13  // Analog Input
#define TEMP_1_PIN                            15  // Analog Input
#define TEMP_BED_PIN                          14  // Analog Input

// SPI for Max6675 or Max31855 Thermocouple
#if DISABLED(SDSUPPORT)
  #define MAX6675_SS_PIN                      -1  // Don't use 53 if using Display/SD card
#else
  #define MAX6675_SS_PIN                      -1  // Don't use 49 (SD_DETECT_PIN)
#endif

//
// Heaters / Fans
//
#define HEATER_0_PIN                          10
#define HEATER_1_PIN                          11
#define HEATER_BED_PIN                         8

#define FAN_PIN                                9
#define FAN1_PIN                               5  // Normall this would be a servo pin

// XXX Runout support unknown?
//#define NUM_RUNOUT_SENSORS                   0
//#define FIL_RUNOUT_PIN                      22
//#define FIL_RUNOUT2_PIN                     21

//
// Misc. Functions
//
//#define CASE_LIGHT_PIN                       5
#define SDSS                                  53
//#ifndef LED_PIN
  //#define LED_PIN                           13
//#endif

//#define SPINDLE_LASER_PWM_PIN               -1  // Hardware PWM
//#define SPINDLE_LASER_ENA_PIN                4  // Pullup!

// Use the RAMPS 1.4 Analog input 5 on the AUX2 connector
//#define FILWIDTH_PIN                         5  // Analog Input

//
// LCD / Controller
//

//#if IS_RRD_SC

#define LCD_PINS_RS                           -1
#define LCD_PINS_ENABLE                       -1
#define LCD_PINS_D4                           -1
#define LCD_PINS_D5                           -1
#define LCD_PINS_D6                           -1
#define LCD_PINS_D7                           -1
//#define BTN_EN1                             31
//#define BTN_EN2                             33
//#define BTN_ENC                             35
#define SD_DETECT_PIN                         49
//#ifndef KILL_PIN
  //#define KILL_PIN                          41
//#endif
//#ifndef BEEPER_PIN
#define BEEPER_PIN                            -1
//#endif

//#endif // IS_RRD_SC