7127 Commits

Author	SHA1	Message	Date
Scott Lahteine	b22d37ba52	Merge pull request #5364 from thinkyhead/rc_croatian_update ... Update Croatian to include missing strings	2016-12-03 11:37:42 -06:00
Robert Marko	b796a687ca	Update Croatian to include missing strings ... Added all missing strings according to English	2016-12-03 11:15:41 -06:00
Scott Lahteine	255ed80164	Fix hotend offset report in M503	2016-12-03 10:17:35 -06:00
Petr Zahradník	c66f3ed34b	Update Czech	2016-12-03 10:32:34 +01:00
Scott Lahteine	cbf208ea1f	Merge pull request #5348 from Kaibob2/patch-1 ... Update language_de.h	2016-12-03 01:53:24 -06:00
Scott Lahteine	a2660cf688	Merge pull request #5347 from tnw513/fix-italian ... Added missing translations	2016-12-03 01:52:45 -06:00
Scott Lahteine	27dd5acc22	Fix set_led_color for BLINKM ... Follow-up to #5330	2016-12-03 01:51:11 -06:00
Kai	8530c32309	Update language_de.h ... Grammar corrections	2016-12-02 19:40:36 +01:00
Silvio Didonna	f1d5ffa211	Added missing translations	2016-12-02 18:49:39 +01:00
Scott Lahteine	b0361ebe4f	Merge pull request #5343 from thinkyhead/rc_invert_case_light ... Allow case light pin to be active low	2016-12-02 01:17:11 -06:00
Scott Lahteine	f60b4f8659	Allow case light pin to be active low	2016-12-01 23:32:34 -06:00
Scott Lahteine	3f4c02e42f	Merge pull request #5259 from Sebastianv650/Allow_UART-ISR_inside_Stepper ... Allow UART ISRs inside the stepper ISR	2016-12-01 23:17:42 -06:00
Scott Lahteine	d07229f185	Fix redraw in SD Card menus	2016-12-01 18:15:58 -06:00
Scott Lahteine	47b4b21308	Merge pull request #5331 from esenapaj/Fix-for-the-PR-#5072 ... Fix for the PR #5072 (Add predefined AUTO_FAN_PINs to pins files), etc	2016-12-01 13:37:02 -06:00
Scott Lahteine	8d14420331	Fix compile without ENABLE_LEVELING_FADE_HEIGHT	2016-12-01 11:37:24 -06:00
Scott Lahteine	415294801f	Merge pull request #5330 from thinkyhead/rc_rgb_led ... Support for an RGB LED using 3 pins	2016-11-30 14:14:00 -06:00
esenapaj	0909cf3d46	Adjust spacing	2016-11-30 19:39:39 +09:00
esenapaj	8e9e9c17b0	Follow-up the PR #5323 (Adding ukrainian language support) ... ・Update forgotten Configuration_adv.h of Felix\DUAL and K8400\Dual-head	2016-11-30 19:39:39 +09:00
esenapaj	d92ce8849b	Fix for the PR #5072 (Add predefined AUTO_FAN_PINs to pins files), etc ... ・Make descriptions the same as others	2016-11-30 19:39:38 +09:00
Scott Lahteine	e00b380489	Merge pull request #5323 from akaJes/lang-ua ... Adding ukrainian language support	2016-11-30 01:10:40 -06:00
Scott Lahteine	65c50e062e	Support for an RGB LED using 3 pins	2016-11-30 00:02:31 -06:00
esenapaj	3047f3c85c	Suppress warning	2016-11-30 00:32:56 +09:00
jes	f674246397	extend Configurations files	2016-11-29 15:04:36 +02:00
jes	c90191faaf	adding ukrainian laguage support	2016-11-29 14:49:45 +02:00
Sebastianv650	912704a0d8	Enable ISRs inside temperature ISR ... to capture chars at UART at 250000 baud.	2016-11-28 20:08:50 +01:00
Sebastianv650	f62f4006af	Account for LCD improvements in ENSURE_SMOOTH_MOVES ... .. and give the hint to try lower values if possible.	2016-11-28 17:44:19 +01:00
Scott Lahteine	092e949b58	Merge pull request #5169 from thinkyhead/rc_core_inverted ... Support for COREYX, COREZX, COREZY	2016-11-28 02:26:41 -06:00
Scott Lahteine	e9e4208ff1	Merge pull request #5274 from Sebastianv650/improve_smooth_moves ... Improvement for ENSURE_SMOOTH_MOVES	2016-11-28 02:22:08 -06:00
Scott Lahteine	c7935bb0d2	Merge pull request #5299 from thinkyhead/rc_bed_correction_fade ... Add a fade factor for mesh leveling	2016-11-28 02:07:51 -06:00
Scott Lahteine	a69b1ee691	Merge pull request #5313 from thinkyhead/rc_fix_menu_actions ... Keep drawing menu unless screen changes	2016-11-28 02:01:39 -06:00
Scott Lahteine	32ee3acf86	Merge pull request #5315 from thinkyhead/rc_fixup_material_menus ... Refine material heatup menu items	2016-11-28 01:46:51 -06:00
Scott Lahteine	c70a06daf1	lcd_save_previous_menu => lcd_save_previous_screen	2016-11-28 01:46:18 -06:00
Scott Lahteine	13ea43cc8d	Only exit menu handler when the screen changes	2016-11-28 01:46:18 -06:00
Scott Lahteine	f45b6a7762	Merge pull request #5314 from thinkyhead/case_light_menu_fix ... Fix and optimize case-light code	2016-11-28 01:45:27 -06:00
Scott Lahteine	59fafb93b2	Merge pull request #5304 from AnHardt/pixel-shifting ... MENU_HOLLOW_FRAME for the menu screens	2016-11-28 01:41:47 -06:00
Scott Lahteine	0951d385ce	Don't set heater temperature above its maximum	2016-11-28 01:37:24 -06:00
Scott Lahteine	c9193e856d	Limit preheat parameters based on all nozzles	2016-11-28 01:37:24 -06:00
Scott Lahteine	bb4529f7d2	PLA / ABS => Material 1 / 2	2016-11-28 01:37:24 -06:00
Scott Lahteine	61437d988a	Fix and optimize case-light code	2016-11-28 01:34:52 -06:00
AnHardt	7a9fa78822	MENU_HOLLOW_FRAME for the menu screens ... MENU_HOLLOW_FRAME for the menu screens and some pixel shifting to optimize the look with tall fonts. (cn)	2016-11-27 22:59:05 +01:00
AnHardt	24ca1a6289	Not more then 4 stripes for u8g-devices ... To optimise speed. Costs well invested 128Byte of RAM.	2016-11-26 19:08:33 +01:00
Scott Lahteine	aee71c543e	Minor formatting in language.h	2016-11-26 06:53:52 -06:00
Scott Lahteine	05d8d189f6	Adjust spacing in utf_mapper.h	2016-11-26 06:53:52 -06:00
Scott Lahteine	5460a529da	Add option DOGM_SPI_DELAY_US	2016-11-26 06:53:52 -06:00
Scott Lahteine	71842b6a17	Apply const to LCD arguments and locals	2016-11-26 06:53:52 -06:00
Scott Lahteine	b1abd7edef	Optimize graphical display with selective rendering	2016-11-26 06:53:52 -06:00
AnHardt	b91fab2d7d	Fix USE_BIG_EDIT_FONT	2016-11-26 13:50:25 +01:00
Scott Lahteine	4cd73e183d	Hide hidden files and folders	2016-11-26 06:26:28 -06:00
Scott Lahteine	f6f77d34a1	Add a fade factor for mesh leveling	2016-11-26 03:41:26 -06:00
AnHardt	75fdcc14b7	Activate font and mapper for el-gr	2016-11-26 02:30:37 +01:00
AnHardt	a0004e7cd3	Change font decent to -1 for tt and gr ... For speeding up font drawing unify font decent. Tr and Gr have ben the only fonts with a font decent of -2. Sorry for some, a bit compressd, but hopefully still readeble symbols.	2016-11-26 02:29:23 +01:00
Scott Lahteine	307f263f89	Merge pull request #5292 from esenapaj/Update-Japanese-translation ... Update Japanese translation	2016-11-25 16:56:49 -06:00
esenapaj	7070143042	Update Japanese translation ... ・Add new translation	2016-11-24 21:10:40 +09:00
esenapaj	ef97645002	Follow-up the PR #5255 (Case light menu (3rd attempt))	2016-11-24 19:42:05 +09:00
Scott Lahteine	2a9b3376a9	Merge pull request #5289 from thinkyhead/rc_which_menu_actions ... Drop "static" keyword in ultralcd.cpp function declarations	2016-11-23 23:04:05 -06:00
Scott Lahteine	b97dafe4b8	Drop "static" keyword in ultralcd.cpp function declarations	2016-11-23 20:43:01 -06:00
Scott Lahteine	2e966f8e5b	Patch Capabilities Report for "PROGRESS"	2016-11-23 19:31:46 -06:00
Scott Lahteine	f60321d3e3	Merge pull request #5284 from thinkyhead/rc_turkish_update ... Turkish update (squashed)	2016-11-23 14:57:52 -06:00
Mehmet Sutas	a26668b10c	Add UTF8 Turkish Translation	2016-11-23 14:19:16 -06:00
Mehmet Sutas	61aa796307	Added Human Readable Comments	2016-11-23 14:19:16 -06:00
Mehmet Sutas	6fb9c6fe07	Follow-up for #5167 Turkish Language ... Add check for Turkish Font before setting better font for graphic displays	2016-11-23 14:19:15 -06:00
Scott Lahteine	d891324830	Merge pull request #5258 from mosh1/mbl_speed_fix ... Fix z feedrate value when doing mesh bed leveling. probe feedrate use…	2016-11-23 14:15:01 -06:00
Scott Lahteine	7f8133a51f	Merge pull request #5255 from Kaibob2/CaseLightMenu ... Case light menu (3rd attempt)	2016-11-23 13:46:33 -06:00
Kai	e9b42f4f47	Update language_de.h	2016-11-23 19:29:19 +01:00
Kai	0c341f0c50	Added Menu entry for Case light	2016-11-23 19:29:15 +01:00
Scott Lahteine	3bc2273ac9	Comment M540	2016-11-21 18:08:00 -06:00
Scott Lahteine	14b74181f5	Merge pull request #5179 from thinkyhead/rc_TMC2130 ... TMC2130 "Silent StepStick" support	2016-11-21 14:10:52 -06:00
Scott Lahteine	bb2114a060	Merge pull request #5264 from thinkyhead/rc_delta_safe_zone ... Add an option for delta to home to the top	2016-11-21 13:56:44 -06:00
Scott Lahteine	38466b1d2f	Merge pull request #5271 from esenapaj/Fix-for-the-PR-#5267 ... Fix for thePR #5267 (Introduce a +1234.56 format for over 999 steps/mm)	2016-11-21 13:55:56 -06:00
Scott Lahteine	9b96a4a53b	Merge pull request #5246 from thinkyhead/rc_some_cleanup ... Minor stepper cleanup	2016-11-21 13:55:25 -06:00
Sebastianv650	8190483eeb	Improvement for ENSURE_SMOOTH_MOVES ... Instead of waiting for a single long block, compare the complete block buffer runtime for the long_move() check.	2016-11-21 17:58:24 +01:00
esenapaj	da67037550	Fix for thePR #5267 (Introduce a +1234.56 format for over 999 steps/mm) ... ・Fix memory leak	2016-11-21 22:31:01 +09:00
Scott Lahteine	0f891e848b	Merge pull request #5268 from esenapaj/Update-Japanese-translation ... Update Japanese translation	2016-11-21 03:18:36 -06:00
esenapaj	190a04c467	Update Japanese translation ... ・Change translation for 16 width LCD	2016-11-21 17:51:43 +09:00
esenapaj	7b836a4000	Introduce a +1234.56 format for over 999 steps/mm	2016-11-21 17:45:07 +09:00
Scott Lahteine	3e0376b45e	Reorder M114 and M119 gcode cases	2016-11-21 00:52:19 -06:00
Scott Lahteine	644fac5d34	Reduce all stepper_indirection init code with macros	2016-11-21 00:52:18 -06:00
Scott Lahteine	4e4f37b6c2	Code formatting for TMC and L6470 config options	2016-11-21 00:52:18 -06:00
Scott Lahteine	127e21ae00	Extend M122 for all steppers	2016-11-21 00:52:18 -06:00
Scott Lahteine	bf5f5f44cc	Make TMC2130 init code auto-configure ... Simply apply enabled settings instead of requiring users to edit stepper_indirection.cpp	2016-11-21 00:52:17 -06:00
Moritz	d67c1d825f	Add TMC2130 support	2016-11-21 00:17:45 -06:00
Scott Lahteine	11effeee2c	Add an option for delta to home to the top	2016-11-20 23:12:07 -06:00
Sebastianv650	50059690e0	Allow UART ISRs inside the stepper ISR ... If the stepper ISR takes too long, chars are lost which leads to serial communication errors like "Line number not +1" or "Wrong checksum". In worst case, the printer can even do crazy moves. With this changes, UART interrupts are handled inside the stepper ISR. This way, no chars should be lost.	2016-11-20 13:09:12 +01:00
Moshen Chan	29b174bfb9	Fix z feedrate value when doing mesh bed leveling. probe feedrate uses XY_PROBE_SPEED	2016-11-19 16:34:41 -08:00
AnHardt	88b38eafd8	Endstop interrupt refinement ... At the start of a move, check if the endstops are already triggered. The 'change' interrupts will not see a change if already triggered.	2016-11-19 13:30:49 +01:00
Scott Lahteine	79c8591192	Merge pull request #5253 from thinkyhead/rc_smooth_move_ex-lax ... Ensure smooth print moves even with LCD enabled	2016-11-19 01:38:41 -06:00
Scott Lahteine	0215cacb30	Merge pull request #5247 from esenapaj/Re-follow-the-PR-#4634 ... Re-follow the PR #4634 (Set language display charset in language.h)	2016-11-19 01:32:40 -06:00
Scott Lahteine	2cc32d85a3	Adjust ENSURE_SMOOTH_MOVES coding style	2016-11-19 01:28:48 -06:00
Scott Lahteine	072541f286	Update ENSURE_SMOOTH_MOVES in all configs	2016-11-19 01:28:47 -06:00
Sebastianv650	de89dc9f04	Ensure smooth print moves even with LCD enabled ... lcd_update can take so much time that the block buffer gets drained if there are only short segments. This leads to jerky printer movements for example in circles and a bad print quality. This change implements a simple check: Only if the block currently executed is long enough, run lcd_update. This also means the printer will not show actual values on the LCD nor will it respond to buttons pressed. A option that keeps the menu accessible is also available. Aditionaly, slow down if a block would be so fast that adding a new block to the buffer would take more time. In this case, the buffer would drain until it's empty in worst case.	2016-11-19 01:28:47 -06:00
Scott Lahteine	87b6b19256	Patch CASE_LIGHT typo	2016-11-18 23:49:12 -06:00
Scott Lahteine	0be6167f14	Merge pull request #5250 from CONSULitAS/RCBugFix_K8200_backinsync_2016-11-18 ... K8200: Example configuration back in sync	2016-11-18 22:49:18 -06:00
Scott Lahteine	eb714ee873	Move dummy thermistor opts, fix redundant sensor comment	2016-11-18 22:24:48 -06:00
Scott Lahteine	7a99c6ce4f	Reformat temp sensor listing	2016-11-18 22:24:47 -06:00
Scott Lahteine	181cdb3cfe	Move GCode list above include lines	2016-11-18 22:24:46 -06:00
Scott Lahteine	25d0c167bd	More detailed static_assert messages	2016-11-18 22:24:46 -06:00
Scott Lahteine	eb120e518c	Followup to new endstop interrupts feature ... - Fix typos, verbiage - Fix naming of `setup_endstop_interrupts` - Some formatting, indentation, spacing	2016-11-18 21:53:45 -06:00
Scott Lahteine	832fe284b4	Merge pull request #5184 from AnHardt/endstop_interrupts ... Introduce endstop interrupts	2016-11-18 20:50:24 -06:00
CONSULitAS	cbae44df64	K8200: Example configuration back in sync ... Configuration.h: back in sync, new features configured Configuration_adv.h: back in sync, new features configured README.md: text updated	2016-11-18 22:55:02 +01:00
esenapaj	5db3738fe7	Re-follow the PR #4634 (Set language display charset in language.h)	2016-11-18 17:44:49 +09:00
Scott Lahteine	6eb6f12c64	Patch up some language formatting	2016-11-18 01:16:58 -06:00
Bo Herrmannsen	8cffa60cc5	Update to Danish language 10/11-2016	2016-11-18 01:16:57 -06:00
Scott Lahteine	98600e1433	Minor stepper cleanup	2016-11-18 01:15:57 -06:00
Florian Heilmann	d08867986e	Add autotemp capabilities to M104 ... This allows M104 to pass the F and B parameters to enable autotemp as well	2016-11-17 11:28:19 -06:00
Sebastianv650	c11b2bb777	Bugfix LIN_ADV ... Advance has nothing todo with Z_AXIS, strange copy&paste error?	2016-11-17 11:28:19 -06:00
Scott Lahteine	ee0765e872	Merge pull request #5233 from esenapaj/Update-Japanese-translation ... Update Japanese translation	2016-11-17 03:38:19 -06:00
Scott Lahteine	2330619da0	Merge pull request #5191 from petrzjunior/const ... Replace const bool with #define for consistency	2016-11-17 03:37:32 -06:00
esenapaj	b278b7a395	Update Japanese translation ... Only adjust spacing	2016-11-17 09:05:51 +09:00
Petr Zahradník junior	d7ce5d271b	Replace const bool with #define for consistency	2016-11-16 18:55:21 +01:00
Scott Lahteine	d63230d73e	Merge pull request #5192 from Kaibob2/patch-7 ... Printer Stats / Completed prints line doesn't fit in display (when german)	2016-11-16 00:16:36 -06:00
Scott Lahteine	548b45026d	Merge pull request #5214 from Sebastianv650/RCBugFix_planner_opt ... Save some cycle inside the planner	2016-11-16 00:06:55 -06:00
Scott Lahteine	5d23e52d75	Merge pull request #5228 from thinkyhead/rc_keep_last_mix ... Fix DIRECT_MIXING_IN_G1 to preserve the previous mix	2016-11-15 19:12:01 -06:00
Scott Lahteine	db47aa983d	Merge pull request #5226 from mtowara/RCBugFix ... bump -std in Makefile to c++11	2016-11-15 16:13:32 -06:00
Scott Lahteine	99b0c1fe56	Fix DIRECT_MIXING_IN_G1 to preserve the previous mix	2016-11-15 16:12:26 -06:00
Markus Towara	23a675f621	reduce binary size of .hex ... still a few bytes bigger than with arduino but nothing major	2016-11-15 21:57:15 +01:00
Markus Towara	5b6e2cecf5	bump c/c++ standard to gnu11 ... needed for constexpr	2016-11-15 21:54:12 +01:00
Scott Lahteine	410657b050	Fix G30 with limits, print correct probe XY	2016-11-15 14:10:28 -06:00
AnHardt	f3eee02596	Introduce endstop interrupts ... If ENDSTOP_INTERRUPTS_FEATURE is enabled this tries to set up interrupt routines for all used endstop pins. If this worked without errors, `endstops.update()` is called only if one of the endstops changed its state. The new interrupt routines do not really check the endstops and react upon them. All what they do, is to set a flag if it makes sense to call the endstop test we are used to. This can be used on: * ARM (DUE) based boards - all pins can raise interrupts, * RAMPS - all 6 endstop pins plus some other on EXT-2 can raise interrupts, * RAMPS based boards - as long the designers did not change the pins for the endstops or at least left enough, * all boards, if there are enough pins that can raise interrupts, and you are willing/able to swap with pins dedicated to other purpose.	2016-11-15 12:07:41 +01:00
Sebastianv650	e3ffb58fbd	Save some cycle inside the planner ... planner.h: fan speed is used to set integer variables, so no need for long. Basicaly a byte should be enough for all the fan things, as it's 0-255? planner.cpp: Save some float multiplications. We could squeeze out even more by defining feedrate_percentage, saved_feedrate_percentage and flow_percentage as float instead of int. Everytime they are used in the time-critical planner, they are casted to float and multiplied by 0.01. Not done jet, as they are used in LCD menu functions I don't know well enough.	2016-11-13 13:34:12 +01:00
Scott Lahteine	665b7f3893	Merge pull request #5212 from thinkyhead/rc_mixing_faster ... Store mix factors as reciprocals and multiply	2016-11-12 18:47:11 -06:00
Scott Lahteine	60cc9342a4	Merge pull request #5188 from thinkyhead/rc_extended_host_support ... Extended host support: M155 Auto temp report, M115 capabilities	2016-11-12 15:38:06 -06:00
Scott Lahteine	f663220e87	Store Mix factors as reciprocals and multiply	2016-11-12 15:19:18 -06:00
Scott Lahteine	ea3c08d249	Merge pull request #5186 from esenapaj/Follow-up-the-PR-#5167-etc ... Follow up the PR #5167 (Add Turkish Language) again, etc	2016-11-12 13:11:54 -06:00
Scott Lahteine	c488378532	Merge pull request #5205 from Sebastianv650/RCBugFix_stepperpatch ... Remove useless line from stepper ISR	2016-11-12 12:43:07 -06:00
Michael Neumann	8bdf303da0	Update pins_MEGATRONICS_3.h	2016-11-12 12:26:07 +01:00
Michael Neumann	3890366c83	Update pins.h	2016-11-12 12:25:45 +01:00
Michael Neumann	c0d45ca7f2	Update boards.h	2016-11-12 12:24:47 +01:00
Sebastianv650	cdc18f8c22	Remove useless line from stepper ISR ... The flag is already set inside planner.get_current_block(). Doing it twice isn't making it better..	2016-11-11 19:35:03 +01:00
Kai	8e8b4398f3	Printer Stats / Completed prints line doesn't fit in display (when german)	2016-11-09 22:03:25 +01:00
Scott Lahteine	b31a07e261	Stateful M355 with separate P parameter	2016-11-09 03:28:18 -06:00
Scott Lahteine	3c9a838651	Extended capabilities report in M115	2016-11-09 02:32:58 -06:00
Scott Lahteine	68b866b5dd	Add M155 - Auto-report temperature with interval	2016-11-09 02:32:58 -06:00
Scott Lahteine	68b46fb2c9	Allow send to i2c address 0 (broadcast)	2016-11-08 17:54:55 -06:00
Scott Lahteine	75bfde9945	M155=>M260, M156=>M261	2016-11-08 17:54:54 -06:00
esenapaj	2ae72b0491	Follow up the PR #5167 (Add Turkish Language) again, etc ... ・Update forgotten K8400\Dual-head\Configuration.h ・Adjust spacing	2016-11-09 06:31:21 +09:00
Scott Lahteine	06f2282f82	Merge pull request #5176 from thinkyhead/rc_filchange_feedback ... Give instant feedback for filament change	2016-11-07 12:11:54 -06:00
Scott Lahteine	dcfd7c69e8	Merge pull request #5163 from nzinov/RCBugFix ... Improve G30 probing command - add optional arguments	2016-11-07 11:37:13 -06:00
Scott Lahteine	e765eebfb0	Patch spacing in bilinear grid report	2016-11-07 04:08:25 -06:00
Scott Lahteine	7780052fb3	Give instant feedback for filament change	2016-11-07 03:48:16 -06:00
esenapaj	24e3f7abe7	Update Turkish translation ... ・Add new translation	2016-11-07 04:59:18 +09:00
esenapaj	be48792e9c	Follow up the PR #5167 (Add Turkish Language), etc ... ・Remove all the #ifndef ・Follow the PR #4603 (Strip never-translated strings from language files) ・Follow the PR #4634 (Set language display charset in language.h) ・Follow the PR #4936 (Put max_jerk vars in array, clean up jerk code) ・Adjust spacing	2016-11-06 23:59:02 +09:00
Scott Lahteine	1864b282c5	Implement reversed CORE options	2016-11-05 23:47:51 -05:00
Scott Lahteine	e3c8318504	Add reversed CORE options	2016-11-05 23:47:46 -05:00
Rigid3D	2327764980	Add Turkish Language	2016-11-05 21:06:16 -05:00
Nikolay Zinov	dea00bbcf1	improve G30 probing ... Add optional parameters X, Y for probe point S sets stowing on and off	2016-11-05 13:22:45 +03:00
Scott Lahteine	00662b8635	Minor babystep cleanup patches	2016-11-03 23:31:45 -05:00
Scott Lahteine	cad792e702	Reduce code for invariant lcd_detected	2016-11-03 23:31:45 -05:00
Scott Lahteine	b23d255491	Move macros above Stepper::babystep	2016-11-03 23:31:45 -05:00
Scott Lahteine	cc57d46158	Fix set_position for CoreYZ	2016-11-03 23:31:45 -05:00
Scott Lahteine	0269347682	Merge pull request #5141 from thinkyhead/rc_old_slowdown_what ... OLD_SLOWDOWN does nothing, so remove it	2016-11-03 23:30:43 -05:00
Scott Lahteine	e92e2b2446	Merge pull request #5144 from Sebastianv650/RCBugFix_LIN_ADV_wipe ... Account for wipe moves	2016-11-03 23:19:25 -05:00
Scott Lahteine	176aeafc19	Don't define bilinear_line_to_destination on kinematic setups	2016-11-03 14:10:07 -05:00
Sebastianv650	d448500643	Account for moves with negative E movements ... Added a rule so that LIN_ADVANCE isn't used for moves with negative E movements (de_float will be negative in this cases). I also added a more detailed comment to make it more clear what the if statement does.	2016-11-03 17:01:17 +01:00
Scott Lahteine	236853df22	Corrections to bilinear_line_to_destination ... - Allow more than 9x9 probe points - Account for the probe starting position	2016-11-03 04:43:59 -05:00
Scott Lahteine	0115e495fe	Fix up Dual X switch blocks	2016-11-02 21:38:50 -05:00
Scott Lahteine	2495ab7af2	Make dual_x_carriage_mode an enumeration	2016-11-02 21:38:49 -05:00
Scott Lahteine	d6c36f5bb9	Fix Z raise with DXC_AUTO_PARK_MODE	2016-11-02 21:36:50 -05:00
Scott Lahteine	0c79553fc5	Cast int to AxisEnum for some accessors	2016-11-02 17:42:24 -05:00
Scott Lahteine	adbf1f7dca	Add M355 to the GCodes list.	2016-11-02 16:43:52 -05:00
Scott Lahteine	63efc10599	Merge pull request #5134 from thinkyhead/rc_bilinear_split_lines ... Split cartesian moves on grid boundaries with bilinear ABL	2016-11-02 16:14:55 -05:00
Scott Lahteine	12167bc8f3	OLD_SLOWDOWN does nothing, so remove it	2016-11-02 01:28:19 -05:00
esenapaj	c8c1a28f6f	Follow-up the PR #5089 (Centralize click-handling in the LCD loop) ... bool feedback is no longer used	2016-11-02 08:36:02 +09:00
esenapaj	c3a105186d	Follow-up the PR #5133 (M355 Case light) ... ・Add CASE_LIGHT_PIN into pinsDebug.h	2016-11-02 00:31:50 +09:00
Scott Lahteine	ee5b8d6dc8	Split moves on grid boundaries with bilinear ABL on cartesian	2016-11-01 08:25:47 -05:00
Scott Lahteine	66744a6076	Merge pull request #5133 from thinkyhead/rc_M355_case_light ... M355 Case light	2016-11-01 07:51:27 -05:00
Scott Lahteine	955d14acb0	Patch photo pin code style	2016-11-01 06:30:14 -05:00
Stanley	ab3f966f5f	Case light G-code M355 ... implemented G-Code M355 into Marlin	2016-11-01 06:30:14 -05:00
Scott Lahteine	8b44413498	Merge pull request #5124 from Sebastianv650/RCBugFix_LIN_ADV-Patch ... BugFix for incorrect E-speed calculation	2016-11-01 05:13:17 -05:00
Scott Lahteine	f418e82b15	Remove redundant definition of EN_C	2016-11-01 05:10:07 -05:00
Sebastianv650	f9bea7968f	BugFix for incorrect E-speed calculation ... The extrusion speed was wrong due to a not high enough precision of esteps to XY steps, therefore now the target float values are used to calculate the ratio between XY movement and extrusion speed. The e_speed_multiplier8 was replaced by an absolute multiplier called abs_adv_steps_multiplier8, therefore one multiplication and bitshift can be saved inside the stepper ISR. Due to this, also extruder_advance_k is better suited inside the planner and not the stepper files any more.	2016-11-01 08:08:47 +01:00
Bob-the-Kuhn	c20b4098be	2 bug fixes & some minor changes ... see detailed description in PR #5118	2016-11-01 01:29:41 -05:00
Scott Lahteine	fa6bf12697	Merge pull request #5118 from thinkyhead/rc_expanded_M43 ... Enhancements to M43 pins debugging	2016-10-31 08:29:53 -05:00
Scott Lahteine	3a107e280d	Developer note in pins_MIGHTYBOARD_REVE.h	2016-10-31 08:22:39 -05:00
Scott Lahteine	85e307dcd8	No FAN0_PIN	2016-10-31 08:08:03 -05:00
Scott Lahteine	ff3a8ca0d1	Use NUM_DIGITAL_PINS instead of custom DIO_COUNT	2016-10-31 08:08:03 -05:00
Scott Lahteine	04a1fac029	Some cleanup to M43	2016-10-31 08:08:03 -05:00
Scott Lahteine	24f6612551	Reduce and optimize endstop_monitor code	2016-10-31 08:08:03 -05:00
Scott Lahteine	b4444e91ae	Reduce code and build size of PWM_details	2016-10-31 08:08:02 -05:00
Scott Lahteine	dbe414ef03	Squash redundant code in PWM_status	2016-10-31 08:08:02 -05:00
Scott Lahteine	af26d22741	Clean up some spacing and semantics	2016-10-31 08:08:02 -05:00
Bob-the-Kuhn	81397d7a9a	EXTRUDER_x_AUTO_FAN name change to Ex_AUTO_FAN ... I stumbled across a name change that'll be used a lot so I'm updateing the name list.	2016-10-31 08:08:02 -05:00
Bob-the-Kuhn	c7f1f0dae6	Add endstop monitor & make pins report pretty	2016-10-31 08:08:02 -05:00
Scott Lahteine	d567b426d5	Merge pull request #4894 from thinkyhead/rc_mightyboard_rev_e ... Mightyboard Revision E preliminary support	2016-10-31 08:01:41 -05:00
Scott Lahteine	43df9ace4e	Merge pull request #5110 from thinkyhead/rc_z2_min_allowed ... Support Z2 min in M119 report	2016-10-31 07:59:45 -05:00
Scott Lahteine	23f05f8be7	Use bit-length types in block_t	2016-10-30 16:16:29 -05:00
Scott Lahteine	8dc7807d85	Add support for CoreYZ to planner.buffer_line	2016-10-30 16:16:28 -05:00
Scott Lahteine	1cf878fdb1	Calculate dm and e-steps earlier in planner	2016-10-30 16:16:28 -05:00
Scott Lahteine	75dbb71dd7	Replace block.busy with a block.flag bit	2016-10-30 16:16:28 -05:00
Scott Lahteine	c7f22f688f	buffer_line can calculate while it's waiting	2016-10-29 17:08:42 -05:00
Scott Lahteine	f3720f4e81	const arguments to test_dual_z_endstops	2016-10-29 16:01:27 -05:00
Scott Lahteine	8cebd2a7db	Arrange Z2 min before Z2 max	2016-10-29 01:54:19 -05:00
Scott Lahteine	accabf088a	Add support for Z2 min endstop to M119	2016-10-29 01:54:02 -05:00
Scott Lahteine	396434a445	Fix compiler warning in M145	2016-10-28 20:57:36 -05:00
Scott Lahteine	8e787304c9	const float ref args in planner.h	2016-10-28 20:57:36 -05:00
Scott Lahteine	07bfc45df8	Adjust spacing in gcode_M149	2016-10-28 20:57:36 -05:00
Scott Lahteine	1a2310c494	Make LCD preheat vars an array to reduce code size	2016-10-28 20:57:36 -05:00
Scott Lahteine	1226ae1912	Some cleanup in ultralcd.h	2016-10-28 20:57:21 -05:00
Scott Lahteine	50ee749082	Centralize click-handling in the LCD loop	2016-10-28 20:57:21 -05:00
Scott Lahteine	47ad97c35e	Merge pull request #5109 from thinkyhead/rc_eeprom_M218_tool_offset ... Save hotend_offset array (M218) in EEPROM	2016-10-28 20:08:29 -05:00
Scott Lahteine	bff6bbdb12	Indentation in configuration_store.cpp	2016-10-28 18:55:42 -05:00
Scott Lahteine	97115d56f9	Print error for M500 with disabled EEPROM	2016-10-28 18:53:48 -05:00
Scott Lahteine	67ab54185b	Save hotend_offset array (M218) in EEPROM	2016-10-28 18:45:23 -05:00
MagoKimbra	dfcdbb437b	Fix Command M420	2016-10-28 20:53:48 +02:00
Scott Lahteine	c34dbfb248	Merge pull request #5072 from thinkyhead/rc_preset_auto_fans ... Add predefined AUTO_FAN_PINs to pins files	2016-10-27 17:12:11 -05:00
Scott Lahteine	9a23f73765	Don't trigger endstops that are actually Z2 or probe	2016-10-27 08:12:17 -05:00
Scott Lahteine	c07cc9e3f1	Revert changes made to z dual endstop test ... #3631 broke z dual endstops. Solved by @Nocturnal42 in https://github.com/MarlinFirmware/Marlin/issues/5078#issuecomment-256572248	2016-10-27 07:41:39 -05:00
Scott Lahteine	c4c53856a4	Merge pull request #5094 from esenapaj/Fix-for-the-PR-#5088 ... Fix for the PR #5088 (Handle M108 in M1 also with ULTIPANEL)	2016-10-26 21:51:18 -05:00
Scott Lahteine	2e3110539b	Merge pull request #5095 from thinkyhead/rc_fix_bilinear_math ... Fix bilinear grid constraints	2016-10-26 21:48:19 -05:00
esenapaj	d5a5042d23	Fix for the PR #5088 (Handle M108 in M1 also with ULTIPANEL)	2016-10-27 10:32:20 +09:00
Scott Lahteine	9cbedab91b	Use DPM where possible	2016-10-26 18:38:32 -05:00
Scott Lahteine	ad38d91692	Sanity check that auto fan pins can do PWM	2016-10-26 18:38:32 -05:00
Scott Lahteine	95275eb9b3	Predefine auto fan pins in some pins files	2016-10-26 18:38:32 -05:00
Scott Lahteine	3f94b15cef	Fix bilinear grid constraints ... Followup to #5090	2016-10-26 18:11:26 -05:00
Scott Lahteine	d439fb95f7	Sanity check for the renamed options	2016-10-26 17:51:26 -05:00
Scott Lahteine	b6aa894893	Rename auto fan pins and add auto fan flags	2016-10-26 17:51:26 -05:00
Scott Lahteine	ada935de87	Allow TEMP_STAT_LEDS with only one LED defined	2016-10-26 17:51:26 -05:00
Scott Lahteine	4b056d8184	Fix warning in ultralcd.cpp	2016-10-26 17:51:26 -05:00
Scott Lahteine	9dfd029911	Fix bug in fastio.h _GET_TIMER	2016-10-26 17:51:25 -05:00
esenapaj	8b1d90e281	Follow-up the PR #5087 (Fixed SERVO pins on Azteeg X3), etc ... ・Add header ・Adjust spacing	2016-10-27 06:46:03 +09:00
Scott Lahteine	bfd3b3c604	Merge pull request #5087 from Fulg/azteeg-x3-pins ... Fixed SERVO pins on Azteeg X3	2016-10-26 06:01:16 -05:00
Scott Lahteine	208d720614	Merge pull request #5082 from Fulg/RCBugFix ... Only issue MAXTEMP when heating	2016-10-26 05:55:33 -05:00
Scott Lahteine	f0d673561f	Fix for bilinear grid outside bounds	2016-10-26 05:00:03 -05:00
Scott Lahteine	24bcea6c02	Merge pull request #5088 from thinkyhead/rc_break_m1_fix ... Handle M108 in M1 also with ULTIPANEL	2016-10-26 00:44:01 -05:00
Scott Lahteine	1ba1ec0db9	Handle M108 in M1 also with ULTIPANEL	2016-10-25 23:25:47 -05:00
Scott Lahteine	7ad33422e3	Clear dir_t size, not pointer size	2016-10-25 22:59:40 -05:00
Benoit Miller	1c716034ec	Fixed SERVO pins on Azteeg X3	2016-10-25 17:11:26 -04:00
Benoit Miller	2aa12d78dc	Only issue MAXTEMP when heating	2016-10-24 17:09:29 -04:00
Scott Lahteine	3fcf915808	Fix uninitialized var in reset_acceleration_rates	2016-10-24 11:55:41 -05:00
Scott Lahteine	14f824c3de	Merge pull request #5071 from esenapaj/Extend-measuring-range-of-thermocouple ... Extend measuring range of thermocouple for MAX31855	2016-10-24 02:00:12 -05:00
Scott Lahteine	1097a50694	Merge pull request #5070 from gcormier/rcbugfix ... Fix #4995 - M48/G29 on CoreXY maybe others?	2016-10-24 00:56:36 -05:00
Sebastianv650	c397b9d60a	Planner acceleration bugfix and speedup v2 ... .) Use already existing inverse_millimeters instead of / block->millimeters. .) Prevent overflow during acceleration calculation by checking if float is necessary. Idea modified from Sailfish. .) Save two uint32_t or even float multiplications by checking if step[AXIS] has steps and if max acceleration is lower than accel. If not, there is no need to check this axis.	2016-10-23 12:47:46 +02:00
esenapaj	70e287ca8c	Extend measuring range of thermocouple for MAX31855	2016-10-23 10:22:39 +09:00
Greg Cormier	f0aed9dac7	Fix #4995 - M48/G29 on CoreXY maybe others?	2016-10-22 20:45:13 -04:00
esenapaj	e50992694f	Fix for the PR #5066 (Updated french translation) ... MSG_INFO_PRINT_TIME is still being used	2016-10-23 06:09:56 +09:00
Scott Lahteine	483082387c	Merge pull request #5022 from esenapaj/Fix-for-the-PR-#4553 ... Fix for the PR #4553 (Save bytes for custom chars (Hitachi LCD))	2016-10-22 13:54:09 -05:00
Scott Lahteine	8b967a9ff0	Merge pull request #5058 from thinkyhead/rc_reverse_arrow_buttons ... Apply encoder reverse options to keypad arrows	2016-10-22 13:52:35 -05:00
esenapaj	523c7eaa6c	Fix for the PR #4553 (Save bytes for custom chars (Hitachi LCD))	2016-10-23 03:29:00 +09:00
Scott Lahteine	ca48a49fdb	Merge pull request #5065 from petrzjunior/transl ... [LANGUAGE] Update Czech (BLTOUCH and DAC strings)	2016-10-22 12:46:10 -05:00
Scott Lahteine	f0744fc815	Merge pull request #5066 from thinkyhead/rc_french_update ... Updated french translation	2016-10-22 12:45:51 -05:00
Gege2B	88b7f6eb46	Updated french translation	2016-10-22 12:30:22 -05:00
Scott Lahteine	3544c3632f	Merge pull request #5062 from thinkyhead/rc_warnings_fix ... Warnings fixed redux	2016-10-22 12:21:36 -05:00
Petr Zahradník junior	8323d78ed7	Translated BLTOUCH and DAC strings	2016-10-22 19:12:21 +02:00
Scott Lahteine	e151f952a3	Apply encoder reverse options to keypad arrows	2016-10-22 11:51:33 -05:00
Scott Lahteine	cfb47929ca	Merge pull request #5060 from thinkyhead/rc_fix_ugly_code ... Reduce, clean up MINTEMP / MAXTEMP test code	2016-10-22 11:27:30 -05:00
Josef Pavlik	dca50737f5	fixed warning: ISO C++ forbids compound-literals	2016-10-22 11:23:16 -05:00
Josef Pavlik	0bd66807b2	fixed warning: extra ;	2016-10-22 11:12:29 -05:00
Josef Pavlik	d35dc407a8	fixed warning: ISO C99 requires rest arguments to be used	2016-10-22 11:12:29 -05:00
Josef Pavlik	c2b51af3ba	fixed warning: ISO C does not permit named variadic macros	2016-10-22 11:12:29 -05:00
Scott Lahteine	0d3fc7dd89	Merge pull request #5059 from gcormier/fixbaby ... Set defer delay back to false when exiting babystepping.	2016-10-22 10:59:17 -05:00
Scott Lahteine	f888597197	Reduce, clean up code for mintemp/maxtemp tests	2016-10-22 10:31:03 -05:00
Scott Lahteine	ad64723354	Move MAX_EXTRUDERS to pins.h	2016-10-22 10:07:51 -05:00
Scott Lahteine	5f5a55a0de	Add a ZERO macro to clear arrays	2016-10-22 10:07:18 -05:00
Greg Cormier	0009725637	Set defer delay back to false when exiting babystepping.	2016-10-22 09:43:30 -04:00
Scott Lahteine	627f9d5285	Merge pull request #5056 from thinkyhead/rc_lin_adv_opt ... LIN_ADVANCE optimizations	2016-10-22 07:06:39 -05:00
Scott Lahteine	0908329d96	Merge pull request #5057 from thinkyhead/rc_mbl_lcd_logical ... Fix manual leveling coordinates	2016-10-22 06:31:02 -05:00
Scott Lahteine	14e60f0d3b	Correct typo in configs ... As pointed out by #5044	2016-10-22 05:56:32 -05:00
Scott Lahteine	1165e83263	MBL coordinates are logical	2016-10-22 05:55:44 -05:00
Scott Lahteine	dbfabb4c0a	Merge pull request #5043 from Kaibob2/patch-5 ... Correct grammar and translation in language_de.h	2016-10-22 05:52:54 -05:00
Scott Lahteine	b19bba275f	No LCD timeout during babystepping ... As requested in #5031	2016-10-22 05:26:07 -05:00
Scott Lahteine	b9109b2875	Improve LIN_ADVANCE commentary (all configs)	2016-10-22 05:03:09 -05:00
Sebastianv650	9818d97587	Fix Z-hops during retract/prime lead to blobs ... We don't want to have retract/prime movements done with LIN_ADVANCE, that's also true with simultaneously executed Z-hops.	2016-10-22 04:54:59 -05:00
Sebastianv650	599649e45d	Add formula for LIN_ADVANCE_K ... With this formula, a start value for K for further fine-calibration can be calculated.	2016-10-22 04:54:59 -05:00
Scott Lahteine	be7d245eff	Merge pull request #5008 from thinkyhead/test_endstop_hits ... Save some PROGMEM in MBL G28	2016-10-22 03:35:52 -05:00
Scott Lahteine	7c0e52256d	Merge pull request #5053 from thinkyhead/rc_fix_baud_config ... Patch BAUDRATE line in configs	2016-10-22 03:27:45 -05:00
Scott Lahteine	2783dcb4cc	Save some RAM in MBL's G29	2016-10-22 02:52:56 -05:00
Scott Lahteine	4f5a8c05d5	Tweaks to endstops macros	2016-10-22 02:52:56 -05:00
Scott Lahteine	083d41a2c2	Remove redundant estep rate code from LIN_ADVANCE ... As noted by https://github.com/MarlinFirmware/Marlin/pull/4971#issuecomment-252503295	2016-10-22 02:19:14 -05:00
Scott Lahteine	4f6bfabaad	Patch BAUDRATE line in configs	2016-10-22 00:48:52 -05:00
Kai	2bfedb74d5	Correct grammar and translation in language_de.h ... Made Filament change Text sound like correct german.	2016-10-19 14:56:46 +02:00
esenapaj	1e1edeadd3	Fix for the commit dc2cb84 (Revert acceleration limiting to avoid overflow) ... ・Add forgotten '\'	2016-10-18 18:07:20 +09:00
Scott Lahteine	dc2cb8454c	Revert acceleration limiting to avoid overflow	2016-10-17 17:08:41 -05:00
Scott Lahteine	6ae5cf17a9	Merge pull request #5033 from esenapaj/Fix-freezing-with-MAX31855 ... Fix freezing and MINTEMP Error with MAX31855 thermocouple	2016-10-17 16:22:20 -05:00
Scott Lahteine	f257c4bcae	Merge pull request #5036 from thinkyhead/rc_dac_code_deps ... Fix DAC current code	2016-10-17 16:19:00 -05:00
Scott Lahteine	b80cc0cbb5	Fix DAC current code	2016-10-17 15:17:57 -05:00
esenapaj	385bd8a4a3	Fix freezing and MINTEMP Error with MAX31855 thermocouple	2016-10-16 07:33:14 +09:00
Scott Lahteine	ca7275a67a	Disable EXTRAPOLATE_FROM_EDGE by default	2016-10-14 14:44:28 -05:00
Scott Lahteine	0921c7da84	Merge pull request #4997 from thinkyhead/rc_jerk_from_mk2 ... Adapt Jerk / Speed code from Prusa MK2	2016-10-12 06:38:50 -05:00
Scott Lahteine	4d89652bc2	Apply minor optimizations to planner.cpp	2016-10-12 04:42:15 -05:00
Scott Lahteine	1092319b19	Adapt speed/jerk code based on Prusa MK2 branch	2016-10-12 04:42:14 -05:00
Scott Lahteine	37643fef63	Merge pull request #4972 from bgort/platformio-improvements ... Move platformio directories out of source tree	2016-10-12 03:42:33 -05:00
Scott Lahteine	8e1cc9332a	Replace block flag bools with flag bits ... …and apply const to some method parameters	2016-10-10 23:17:49 -05:00
Scott Lahteine	d41f2bdbd8	Merge pull request #4991 from thinkyhead/rc_max31855_fix ... Patches for Stepper DAC and MAX31855	2016-10-10 20:12:06 -05:00
Scott Lahteine	e7cf566fc5	Do kinematic segments with buffer_line_kinematic ... This breaks the raw option, but in the future perhaps all planner moves will be sent in raw form instead of logical.	2016-10-10 17:14:03 -05:00
Scott Lahteine	a10e81dc2a	Minor cleanup of set_bed_leveling_enabled	2016-10-10 17:14:03 -05:00
Scott Lahteine	029824bc49	Patch ADJUST_DELTA macro for SCARA	2016-10-10 17:14:03 -05:00
Scott Lahteine	5ce5a9c822	Marlin: planner.h tweak	2016-10-10 17:14:03 -05:00
Scott Lahteine	d963020532	Sort out some header dependencies	2016-10-10 17:14:03 -05:00
Scott Lahteine	e17f9b8b99	DAC patches ... As suggested by #4985	2016-10-10 14:08:04 -05:00
Scott Lahteine	2cb5df8a56	Merge pull request #4984 from esenapaj/Small-fix-for-PR-#4980 ... Small fix for the PR #4980 (LIN_ADVANCE bug fix and optimization)	2016-10-10 13:30:47 -05:00
Scott Lahteine	b6221df3f3	Merge pull request #4983 from MarlinFirmware/revert-4933-rc_drop_pid_func_range ... Revert "Removal of PID functional range"	2016-10-10 13:29:54 -05:00
Scott Lahteine	a07033a6c1	Merge pull request #4974 from esenapaj/Follow-up-the-PR-#4955 ... Fix and follow-up the PR #4955 (PINS_DEBUGGING and M43: Read pin states), etc	2016-10-10 13:27:52 -05:00
Scott Lahteine	f8199b2cc1	Merge pull request #4982 from thinkyhead/rc_abl_bugfix ... Fix planner with kinematics, delta ABL	2016-10-10 13:24:22 -05:00
esenapaj	f41c60d4a4	Follow-up the PR #4955, etc ... ・More ANALOG NUMBERING to Analog Input ・Add comment header to all the section of all the pins files ・Sort sections as follows: 1. Some special definitions (USBCON, LARGE_FLASH, etc) 2. Servos 3. Limit Switches 4. Z Probe 5. Steppers 6. Temperature Sensors 7. Heaters / Fans 8. Misc. Functions 9. LCD / Controller ・Move MAX6675_SS into "Temperature Sensors" section ・Adjust spacing	2016-10-10 14:22:43 +09:00
esenapaj	00456b0cb3	Fix compilation errors	2016-10-10 14:22:43 +09:00
esenapaj	cfb5c24bc9	Small fix for the PR #4980 (LIN_ADVANCE bug fix and optimization) ... ・Fix a comment about timer	2016-10-10 07:48:42 +09:00
Scott Lahteine	149b8d9e4b	Handle MAX31855 error conditions	2016-10-09 17:12:50 -05:00
Scott Lahteine	f4ec265363	Fix a typo	2016-10-09 16:45:29 -05:00
Scott Lahteine	4ec2d459e6	Fix mcp4728_setVref_all as followup to #4967	2016-10-09 16:45:00 -05:00
Scott Lahteine	1e551c0688	Revert "Squashed - Removal of PID functional range"	2016-10-09 16:27:45 -05:00
Scott Lahteine	4037df82b0	Merge pull request #4981 from esenapaj/Update-Japanese-language ... Update Japanese translation, etc	2016-10-09 16:11:53 -05:00
Scott Lahteine	e4e290d957	Make EXTRUDER_RUNOUT_PREVENT kinematic compatible	2016-10-09 15:58:33 -05:00
Scott Lahteine	847429eff4	Make tool_change kinematic compatible	2016-10-09 15:58:32 -05:00
Scott Lahteine	a4a7ca10ca	Make USE_DELTA_IK_INTERPOLATION compatible with ABL	2016-10-09 15:58:32 -05:00
Scott Lahteine	c5cac486f5	Use a, b, c instead of lx, ly, lz	2016-10-09 14:34:24 -05:00
Josef Pavlik	f8c2473a71	Improve planner kinematics, fix delta ABL	2016-10-09 13:32:46 -05:00
Scott Lahteine	48761f2021	Patch delta endstop adjustment config	2016-10-09 13:32:45 -05:00
Josef Pavlik	28d41b48e3	delta endstop adjustment configurable	2016-10-09 13:09:34 -05:00
Scott Lahteine	ff6b23cb0f	Fix an issue with shifted LCD lines	2016-10-09 13:00:00 -05:00
Scott Lahteine	e4d2662d81	Use some macros in M48	2016-10-09 12:21:05 -05:00
Scott Lahteine	3752d9aca8	Fix timer comments	2016-10-09 12:11:00 -05:00
Sebastianv650	a448cedbc5	LIN_ADVANCE bug fix and optimization ... .) long to int: Extruder stalls at 10kHz / 20kHz step limits with long. .) Take the delta_adv_steps calculation out of the step_loops loop. Wasted calculation performance if done inside. .) >> 2 replaced by 3: Is divide by 8. Reason: Timer 0 runs at 16/8=2MHz, Timer 1 at 16/64=0.25MHz. ==> 2/0.25=8.	2016-10-09 11:55:02 -05:00
esenapaj	b27080c1dd	Update Japanese translation ... ・Add new translation	2016-10-10 01:52:51 +09:00
esenapaj	0780146034	Move DAC section from inside of the changing filament section	2016-10-10 01:17:46 +09:00
Brian	9c0404eae4	Move platformio directories out of source tree	2016-10-08 13:45:26 -04:00
Scott Lahteine	a1b50f1102	Cleanup of code style	2016-10-07 15:57:24 -05:00
jaysonkelly	13c9dcc600	Add LCD menu for DAC	2016-10-07 15:13:03 -05:00
Scott Lahteine	00261cbfcb	Merge pull request #4933 from thinkyhead/rc_drop_pid_func_range ... Squashed - Removal of PID functional range	2016-10-07 15:07:55 -05:00
Scott Lahteine	ee01def16d	Merge pull request #4955 from thinkyhead/rc_debug_pins ... PINS_DEBUGGING and M43: Read pin states	2016-10-07 14:47:34 -05:00
Scott Lahteine	a0df34fd4c	Add PINS_DEBUGGING advanced config option	2016-10-07 14:20:13 -05:00
Scott Lahteine	e21bab5243	PINS_DEBUGGING and M43 Read Pins	2016-10-07 14:11:48 -05:00
Scott Lahteine	3c97fa6e29	Merge pull request #4963 from esenapaj/Fix-for-advance-algorithm ... Move routine of direction signal of ADVANCE and LIN_ADVANCE from Stepper::isr() to Stepper::advance_isr()	2016-10-07 00:33:42 -05:00
Scott Lahteine	48e63c4730	Comment some globals	2016-10-06 22:06:33 -05:00
Scott Lahteine	9a6c66602f	Fix formatting of extrapolate debug output	2016-10-06 17:04:22 -05:00
Scott Lahteine	cd77eb5c40	Clear grid for bilinear G29	2016-10-06 17:00:53 -05:00
Scott Lahteine	53a0856f5c	Print Y as int in print_bed_level	2016-10-06 16:46:54 -05:00
esenapaj	f8df88f271	Move routine of direction signal of ADVANCE and LIN_ADVANCE from Stepper::isr() to Stepper::advance_isr()	2016-10-07 02:01:29 +09:00
Brian	357854a7ef	tweak variables;	2016-10-05 19:49:05 -04:00
Brian	48cf19151a	Improve M48 output; Add min, max, range, etc.	2016-10-05 16:09:39 -04:00
Scott Lahteine	c63cb45268	Fix thermal runaway timeout	2016-10-05 08:42:39 -05:00
Scott Lahteine	e6164d254d	Clean up GCode command short comments	2016-10-05 06:13:30 -05:00
Scott Lahteine	47bd142b29	Should marlinAnalogInputToDigitalPin use analogInputToDigitalPin?	2016-10-05 06:13:30 -05:00
Scott Lahteine	bd8520e61d	Label analog pins in a similar way ... Some other pins formatting also	2016-10-05 06:13:30 -05:00
Scott Lahteine	0c0deb5194	Common pin_is_protected function	2016-10-05 04:41:27 -05:00
Scott Lahteine	49d77720d5	More support for 4th extruder or heater	2016-10-05 04:40:22 -05:00
Scott Lahteine	46839c222a	Comment and clean up some vars	2016-10-04 23:40:45 -05:00
Scott Lahteine	8910bb7c97	Fix buzzer conditional compile	2016-10-04 21:38:41 -05:00
Scott Lahteine	de7e798e6f	Replace single-char S_ECHOs with S_CHAR	2016-10-04 21:38:41 -05:00
Scott Lahteine	0e83f34174	Tweak debugging of probe_pt	2016-10-04 21:38:00 -05:00
Scott Lahteine	cc02f6edf8	Merge pull request #4943 from esenapaj/Small-update-of-language_kana_h ... Small update of language_kana.h	2016-10-04 03:21:57 -05:00
Scott Lahteine	ca26011e3c	Merge pull request #4941 from MagoKimbra/rc_fix_M205 ... Add note for M205	2016-10-04 03:21:20 -05:00
Scott Lahteine	9485aa8f13	Include negative Z probe offset in clearance move	2016-10-03 16:18:04 -05:00
Scott Lahteine	5c1eb595e6	Fix for G2/G3 negative radius ... As suggested in #4940	2016-10-03 14:48:44 -05:00
esenapaj	f09ae96f28	Small update of language_kana.h	2016-10-03 23:41:39 +09:00
MagoKimbra	7b37539fe7	Add note for M205	2016-10-03 08:54:15 +02:00
Scott Lahteine	d5f598cd82	Tweak probe debug, add newline	2016-10-02 17:35:40 -05:00
Scott Lahteine	c592ccb6f5	Patch max_jerk[Z] menu item	2016-10-02 10:12:47 -05:00
Scott Lahteine	d80a79eb77	Use right-shift instead of / 2, why not?	2016-10-02 07:01:40 -05:00
Rerouter	02fe9cf558	Removal of functional range constraint ... Also lined up the >> 1 and / 2 mentioned earlier in the unconstrained I term issue,	2016-10-02 07:01:40 -05:00
Rerouter	5f5d87cad3	Update Configuration.h	2016-10-02 07:01:40 -05:00
Scott Lahteine	761593b74b	Cleanup some vars, use of min/max	2016-10-02 06:34:56 -05:00
Scott Lahteine	d19cfcfc1d	max_jerk array, DEFAULT_XYJERK => DEFAULT_[XY]JERK	2016-10-02 06:34:56 -05:00
Scott Lahteine	e7dc174f30	More detailed debugging of G28 delta	2016-10-02 02:18:57 -05:00
Scott Lahteine	473f4a17a8	Merge pull request #4914 from Rerouter/PID-Unconstrained-Itemp ... Pid unconstrained itemp	2016-10-01 06:58:07 -05:00
Scott Lahteine	bad8899ebc	Merge pull request #4900 from thinkyhead/rc_g38_changes ... Cleanup of G38.2 / G38.3	2016-10-01 06:57:17 -05:00
Scott Lahteine	73ce3a61c7	Cleanup, comment zigzag	2016-10-01 05:21:52 -05:00
Scott Lahteine	0d538f3db6	Add to all configurations	2016-10-01 05:00:53 -05:00
Scott Lahteine	919fe3e4b8	Rename feature to G38_PROBE_TARGET	2016-10-01 05:00:53 -05:00
Scott Lahteine	a2864ab7fe	Patched up, cleaned up	2016-10-01 05:00:53 -05:00
Bob-the-Kuhn	2911aa7ffa	code changes to implement G38 commands ... 1) modified 3 code files Marlin.h Marlin_main.cpp endstops.cpp 2) modified config files so I could test on my machine Testing was done on an AzteegX3pro based machine. The probe was hooked to the Z_MIN endstop. My controller doesn't have a dedicated Z_PROBE input so I couldn't test that functionality. Verified that a large file (without any G38 commands) executed the same before and after the changes. Verified that the head moves as expected when G38.2 and G38.3 commands are issued. Single & multiple axis moves were tested along with + and - directions. Code was added to the main ISR. In normal operation only one extra IF statement is evaluated. I didn't notice any performance degradation because of the added code. The G38 commands are expected to be issued manually by the operator during machine setup. The G38 commands wait until the machine is idle before proceeding. That way the other commands are minimally impacted by the extra ISR overhead when a G38 command is in the queue. The G38 commands are very similar to the G28 commands except 1) only the Z_PROBE is used and movement can be in the + or - direction. See issue 4677 for a discussion on adding G38 commands to Marlin. Feature request: add ability to use G38.2 command (CNC) MarlinFirmware/Marlin#4677	2016-10-01 05:00:53 -05:00
Scott Lahteine	74d048e77e	Merge pull request #4927 from thinkyhead/rc_bltouch_noraise ... Don't check Z_MAX on raise when the probe pwns the pin	2016-10-01 04:52:56 -05:00
Scott Lahteine	4afa293289	Say "BLTOUCH" in machine info report	2016-09-30 17:13:27 -05:00
Scott Lahteine	ed7d2694fc	Don't check Z_MAX on raise when the probe pwns the pin	2016-09-30 16:41:30 -05:00
Scott Lahteine	3bbdd48a4d	Merge pull request #4918 from thinkyhead/rc_abl_patchups ... Fix up ABL - Add PROBE_Y_FIRST option. Arduino 1.6.8 required.	2016-09-29 15:29:01 -05:00
Scott Lahteine	fffc9fefa8	Apply changes to all configs	2016-09-29 02:17:33 -05:00
Scott Lahteine	587cb6c283	K8400 has 1xXY an 2xZ endstop plugs	2016-09-29 02:07:22 -05:00
Scott Lahteine	d234bc160e	Require Arduino 1.6.8 to compile	2016-09-29 02:00:27 -05:00
Scott Lahteine	2d2c9bdf92	Add PROBE_Y_FIRST option for probe order	2016-09-29 02:00:27 -05:00
Scott Lahteine	c8c57e59fc	Patch the end of G29 to sync plan position	2016-09-29 02:00:27 -05:00
Scott Lahteine	81b8c9f8ec	Add XY parameters to G29 for mesh dimensions	2016-09-29 02:00:27 -05:00
Scott Lahteine	56cf674150	M420 can now enable/disable ABL	2016-09-29 02:00:26 -05:00
Scott Lahteine	06790977c4	Use updated position methods	2016-09-29 01:31:05 -05:00
Scott Lahteine	e8f2604a6f	Patch print_bed_level numbering	2016-09-29 01:31:05 -05:00
Scott Lahteine	d066610514	Patch up bilinear_z_offset	2016-09-29 01:31:05 -05:00
Scott Lahteine	850e38d013	G30 will only disable bed leveling	2016-09-29 01:31:04 -05:00
Scott Lahteine	510ef5d14a	Standard function to turn bed leveling on/off	2016-09-29 01:27:37 -05:00
Scott Lahteine	ecf7cdde65	Augment planner/stepper getters/setters	2016-09-29 01:27:37 -05:00
Scott Lahteine	2febd8ec82	Double-touch debugging	2016-09-29 01:27:37 -05:00
Scott Lahteine	b331077c32	Use stepper.get_axis_position_degrees	2016-09-29 01:27:37 -05:00
Scott Lahteine	0d9efb24f3	Fix up bilinear_z_offset	2016-09-29 01:26:22 -05:00
jaysonkelly	3b3d282f8e	Adjusted values for Rigidboard Configuration ... Rigidboard differs a little in configuration from the PrinterBoardRevF we modeled the code after.	2016-09-28 14:14:04 -05:00
Scott Lahteine	850259bb25	Watch bed temp also for Control menu item	2016-09-28 14:14:04 -05:00
esenapaj	92c03a44a9	Fix the PR #4899 (ABL: Enable by type. Bilinear for all.) etc. ... About Configuration.h: ・Fix the PR #4899 (ABL: Enable by type. Bilinear for all.) Remove Duplicated contents ・Fix the PR #4305 (Custom boot screen feature improvement) Revert from "during boot" to "during bootup" in all the example Configuration.h ・Fix the PR #4207 (Clean up, simplify and generalize the Allen-key-probe code.) Resolve and relocate the duplicated definitions in Z_PROBE_ALLEN_KEY section ・Follow-up the PR #4805 (Additional documentation of Configuration.h) Add forgotten changes to all the example Configuration.h Adjust spacing About Configuration_adv.h: Add missing description of SLOWDOWN for DELTA Adjust spacing	2016-09-28 14:14:04 -05:00
Rerouter	50e5ee4de4	Update Configuration.h	2016-09-28 17:38:09 +10:00
Rerouter	1a2f1d4974	Update temperature.cpp	2016-09-28 17:36:53 +10:00
Rerouter	a765c98850	Removal of the constraints of the Iterm	2016-09-28 17:26:49 +10:00
Scott Lahteine	8b46eb3766	Fix bilinear interpolation	2016-09-27 03:18:49 -05:00
Scott Lahteine	5100bdac81	Improve Bilinear Grid ... - Extrapolate properly for even numbered grid points - Extrapolate using average, not median - Improve bilinear grid report output - Add debug output for bilinear extrapolation - Add option to extrapolate from edge, not center	2016-09-27 00:03:19 -05:00
Scott Lahteine	a3e91ec65e	Add 'Q' option to G29 when debug leveling is on	2016-09-27 00:03:19 -05:00
Scott Lahteine	1fceda4fb0	Add leveling type and details to machine_info	2016-09-27 00:03:19 -05:00
Scott Lahteine	e0e0166075	Fix auto bed leveling - turn on after successful G29	2016-09-27 00:03:19 -05:00
Scott Lahteine	18e40de39c	Adjust final Z after bilinear G29	2016-09-26 00:22:22 -05:00
Scott Lahteine	ea0dbee3c9	Enable ABL by type, support bilinear on cartesian	2016-09-25 23:35:37 -05:00
Scott Lahteine	9cebbabd05	Merge pull request #4893 from thinkyhead/rc_stat_led_check ... Define status LED pins without condition	2016-09-25 18:50:47 -05:00
Scott Lahteine	5fff8d148b	Clean up digital pots and microsteps	2016-09-25 11:16:22 -05:00
Scott Lahteine	570676d265	Include requirements in "Implemented Codes"	2016-09-25 07:50:33 -05:00
Scott Lahteine	cb48292338	Use fastio for literal pins	2016-09-25 06:33:38 -05:00
Scott Lahteine	07703d2bd6	Use _PIN suffix on some pins	2016-09-25 06:33:38 -05:00
Scott Lahteine	203e519bf4	Sanity check for status LED pins	2016-09-25 06:33:38 -05:00
Scott Lahteine	ba43277429	Always define status LED pins	2016-09-25 06:33:37 -05:00
Scott Lahteine	ad691022d7	Fix up spacing in A4JP pins	2016-09-25 06:33:37 -05:00
Scott Lahteine	fba0b67f7d	Rename status led pins	2016-09-25 06:33:37 -05:00
Scott Lahteine	9d86c07702	Clean up some fastio.h spacing	2016-09-25 06:33:37 -05:00
Scott Lahteine	ab84ed22ca	No such thing as G6 and G7 pins	2016-09-25 05:28:22 -05:00
Scott Lahteine	c2f13be750	Mightyboard Revision E	2016-09-25 05:28:04 -05:00
Scott Lahteine	041d127cd3	Match bltouch test in do_homing_move with new code	2016-09-24 23:58:08 -05:00
Scott Lahteine	16461900c2	Fix for HEATERS_PARALLEL	2016-09-24 05:34:40 -05:00
Scott Lahteine	1583d37edd	Comment on M851 case	2016-09-24 05:34:36 -05:00
Scott Lahteine	076f3a8284	unsigned char => uint8_t	2016-09-24 05:23:40 -05:00
Scott Lahteine	8935bed594	MIDDLE_DEAD_ZONE => MIDDLE_DEAD_ZONE_R	2016-09-24 05:18:36 -05:00
Scott Lahteine	6cf0952bf9	Merge pull request #4887 from thinkyhead/rc_autumn_fixups ... Improve MINIMUM_STEPPER_PULSE	2016-09-24 03:23:42 -05:00
Scott Lahteine	8061f1fac9	Merge pull request #4888 from thinkyhead/fix_warnings_etc ... Suppress warnings, fix nonlinear_z_offset	2016-09-24 03:22:49 -05:00
esenapaj	7bdc58a818	Suppress warnings, fix nonlinear_z_offset	2016-09-24 03:06:08 -05:00
Scott Lahteine	eabff30e75	Improve MINIMUM_STEPPER_PULSE	2016-09-24 02:23:43 -05:00
esenapaj	3ed8f8331c	Update Japanese translation ... ・Add new translation	2016-09-24 09:24:38 +09:00
Scott Lahteine	da1644313d	Merge pull request #4883 from esenapaj/Follow-up-the-PR-#4860 ... Follow-up the PR #4860 (Fix BLTOUCH string and SERVO_DELAY)	2016-09-23 16:39:37 -05:00
Scott Lahteine	903b8bb60c	No need for auto_bed_leveling_was_enabled	2016-09-23 16:38:22 -05:00
esenapaj	ee60225c07	Follow-up the PR #4860 (Fix BLTOUCH string and SERVO_DELAY)	2016-09-24 06:18:27 +09:00
Scott Lahteine	0951bffcc0	Sanity check homing bumps	2016-09-23 15:39:02 -05:00
Scott Lahteine	a9a21db39f	No homing bump if bump distance is 0 (or less)	2016-09-23 15:39:02 -05:00
Scott Lahteine	2b4da57ea7	Patch Z safe homing for probe Z homing	2016-09-23 15:39:02 -05:00
Scott Lahteine	c6dd539c84	Print error for M42 bad pin	2016-09-23 15:39:02 -05:00
Scott Lahteine	8b399610fb	Skip raw moves to current position	2016-09-23 15:39:02 -05:00
Scott Lahteine	22ece0081e	Pass array pointer to unapply_leveling	2016-09-23 15:39:01 -05:00
Scott Lahteine	cbc158eb62	Add a proper flag for ABL enabled	2016-09-23 15:39:01 -05:00
Scott Lahteine	666e944336	Init xProbe/yProbe for compiler	2016-09-23 15:39:01 -05:00
Scott Lahteine	2c52e6ecf4	Clean up G28 MBL code	2016-09-23 15:39:01 -05:00
Scott Lahteine	0bf1054bb2	Patch do_homing_move for SCARA	2016-09-23 15:39:00 -05:00
Scott Lahteine	6ad0da661c	Report position in G92	2016-09-23 15:39:00 -05:00
Scott Lahteine	199a7b5dd5	Tweak SCARA debugging	2016-09-23 15:39:00 -05:00
Scott Lahteine	865ad25781	Fix prepare_kinematic_move_to precision	2016-09-23 15:39:00 -05:00
Scott Lahteine	85e607153b	Improve kinematic optimization options	2016-09-23 03:03:15 -05:00
Scott Lahteine	2846531f0b	const argument in do_homing_move	2016-09-23 03:03:15 -05:00
Scott Lahteine	cc639d7d9c	Less indentation in Stepper::isr	2016-09-23 03:03:14 -05:00
Scott Lahteine	7dec8071b2	Always synchronize in Stepper::set_position	2016-09-23 03:03:14 -05:00
Scott Lahteine	c6142aa2a1	Minor cleanups in Marlin_main.cpp	2016-09-23 03:03:14 -05:00
Scott Lahteine	0427f3cc3b	Use memcpy/memset in planner	2016-09-23 03:03:14 -05:00
Scott Lahteine	6b9bf8e8fe	Add Planner::sync_from_steppers ... Use to sync the planner after an interrupted move (when not overriding the logical position).	2016-09-23 03:03:14 -05:00
Scott Lahteine	be11a8a938	Fix debug in Planner::buffer_line	2016-09-23 03:03:13 -05:00
Scott Lahteine	b211df818e	Make movement functions more available	2016-09-23 03:03:13 -05:00
Scott Lahteine	6335acbf5c	Patch bug in linear unapply_leveling	2016-09-23 03:03:13 -05:00
Scott Lahteine	e8d5073a90	Use probe clearance for bump when homing Z with probe	2016-09-22 15:41:28 -05:00
Scott Lahteine	dbe41245f1	Merge pull request #4821 from thinkyhead/rc_revert_to_raises ... Z Raise/Clearance rather than Height	2016-09-22 15:30:07 -05:00
Scott Lahteine	747a2257dd	Only deploy/stow BLTOUCH on downward move	2016-09-22 15:26:19 -05:00
Scott Lahteine	e242946ac3	Patch G29 for linear leveling, reachable with probe	2016-09-22 15:26:19 -05:00
Scott Lahteine	b800eb0fed	Add probe option to position_is_reachable	2016-09-22 15:26:19 -05:00
Scott Lahteine	fafafcf9d1	Use unapply_leveling in set_current_from_steppers_for_axis	2016-09-22 15:26:18 -05:00
Scott Lahteine	e69d1e2879	Homing/probing feedrate, comments	2016-09-22 15:26:18 -05:00
Scott Lahteine	7d72ed688c	Revert motor_current_setting to constexpr ... We should use `constexpr` wherever it makes sense, for its added benefits. See http://stackoverflow.com/questions/13346879/const-vs-constexpr-on-variables	2016-09-22 15:26:18 -05:00
Scott Lahteine	145d9005d1	Fix BLTOUCH string and SERVO_DELAY	2016-09-21 01:45:23 -05:00
Scott Lahteine	2b7cc27c37	Merge pull request #4840 from thinkyhead/rc_G2_G3_arc_r_method ... Add support for G2/G3 with R parameter	2016-09-21 01:30:37 -05:00
Scott Lahteine	e0e10e0e45	Merge pull request #4859 from thinkyhead/rc_kinematic_and_scara ... Kinematic and SCARA patches	2016-09-21 01:21:49 -05:00
Scott Lahteine	31f03c838a	Only deploy/stow BLTouch for Z axis	2016-09-21 00:54:54 -05:00
Scott Lahteine	3913e04ac7	Add Delta kinematic optimization options	2016-09-20 18:48:06 -05:00
Scott Lahteine	8e31640229	Optimize prepare_kinematic_move_to	2016-09-20 18:48:06 -05:00
Scott Lahteine	fd9b8ae4d4	Use position_is_reachable in G29, M48	2016-09-20 18:48:06 -05:00
Scott Lahteine	7194e4434f	SCARA support in position_is_reachable	2016-09-20 18:48:06 -05:00
Scott Lahteine	1c5f9821c4	SCARA support in homeaxis	2016-09-20 18:48:05 -05:00
Scott Lahteine	92b4459f6c	Simpler G92 for SCARA	2016-09-20 18:48:05 -05:00
Scott Lahteine	46cc2e3f6a	Fix get_cartesian_from_steppers	2016-09-20 18:31:36 -05:00
Scott Lahteine	435c3ed404	Patch SCARA_move_to_cal for coordinate space	2016-09-20 18:31:36 -05:00
Scott Lahteine	5efb12e889	Simpler report_current_position for SCARA	2016-09-20 18:31:36 -05:00
Scott Lahteine	83fc5e1540	No line_to_* functions with IS_KINEMATIC	2016-09-20 18:31:36 -05:00
Scott Lahteine	59d39d7655	G0 direct move for SCARA	2016-09-20 18:31:36 -05:00
Scott Lahteine	ad9d6870ed	SCARA support in do_blocking_move_to	2016-09-20 18:31:36 -05:00
Scott Lahteine	8542ebcecd	prepare_move_to_destination_raw => prepare_uninterpolated_move_to_destination	2016-09-20 18:31:36 -05:00
Scott Lahteine	f900f97611	Update sw endstops in set_axis_is_at_home	2016-09-20 18:31:36 -05:00
Scott Lahteine	0d43cef1de	M206 for MORGAN_SCARA	2016-09-20 18:31:36 -05:00
Scott Lahteine	e94cb7a380	MORGAN_SCARA kinematics	2016-09-20 18:31:36 -05:00
Scott Lahteine	890bade2fa	Additions, mods to SCARA config	2016-09-20 18:31:36 -05:00
Scott Lahteine	01f1028510	Try on "CLEARANCE" for size	2016-09-20 18:29:49 -05:00
Scott Lahteine	0e7d638a7a	Revert to Probe Raise rather than Probe Height	2016-09-20 18:29:49 -05:00
Scott Lahteine	51e42a2d77	Adjust BLTouch probe behavior ... Addressing #4855 - Have the pin deploy only immediately before probing - Have the pin retract immediately after every probe	2016-09-20 16:20:36 -05:00
Scott Lahteine	13523cbf29	Fix and extend BLTouch support	2016-09-20 16:20:36 -05:00
Scott Lahteine	5cbed13f41	'constexpr' => 'const' for PWM_MOTOR_CURRENT	2016-09-20 15:57:48 -05:00
Scott Lahteine	7ae351c92f	Merge pull request #4842 from thinkyhead/rc_DISABLE_Z_MIN_PROBE_ENDSTOP_whassup ... Drop DISABLE_Z_MIN_PROBE_ENDSTOP, clean up probe config	2016-09-20 12:16:51 -05:00
Scott Lahteine	ba94c89e21	Merge pull request #4852 from esenapaj/Fix-for-advance-extrusion-algorithms ... Fix for advance extrusion algorithms	2016-09-20 11:33:14 -05:00
esenapaj	954563d603	Adjust spacing	2016-09-20 19:35:44 +09:00
esenapaj	7e9576dc5b	Extend the e_steps[] from int to long for allowing more than 32,767 E steps ... Probably needed for long straight lines when using high microstepping	2016-09-20 19:35:44 +09:00
esenapaj	b04ed8f9c3	Fix inverted stepper signal of ADVANCED and LIN_ADVANCED	2016-09-20 19:35:44 +09:00
esenapaj	8692748ecd	Fix broken direction signal of ADVANCED and LIN_ADVANCED ... Remove a setting proccess of E direction in advance_isr()	2016-09-20 19:35:44 +09:00
Scott Lahteine	e9ce42353e	Patch G29 for 3-point leveling	2016-09-20 04:46:41 -05:00
Scott Lahteine	c2744d8a8b	Add support for G2/G3 with R parameter	2016-09-19 00:35:09 -05:00
Scott Lahteine	e05af606a8	Clean up probe config options	2016-09-19 00:26:16 -05:00
Scott Lahteine	153e240cdd	Probe conditionals to Conditionals_LCD.h	2016-09-19 00:25:53 -05:00
Scott Lahteine	ff38a3c3b1	Use SD Detect Pin 53 for 3DRAG, K8200, and K8400 ... See #4316	2016-09-18 23:46:09 -05:00
Scott Lahteine	f38a33a5d8	Add handling of BLTouch error state	2016-09-18 22:00:32 -05:00
Scott Lahteine	c4dcfa254e	Allow override of Z_ENDSTOP_SERVO_NR with BLTOUCH	2016-09-18 22:00:32 -05:00
Scott Lahteine	7d9ebda478	Remove redundant servo probe sanity check	2016-09-18 21:46:18 -05:00
Scott Lahteine	f0beae7641	Fix stupid, stupid, stupid oversight in G29 update ... Mea culpa!	2016-09-18 16:24:47 -05:00
Scott Lahteine	77639672d7	Move NONLINEAR bed leveling to planner ... This is in advance of moving non-linear bed leveling to the planner class.	2016-09-18 13:50:38 -05:00
Scott Lahteine	9429c7db89	Use ABC indices in delta[]	2016-09-18 13:50:38 -05:00
Scott Lahteine	5f2f991192	Use 'logical' rather than 'target' or 'cartesian'	2016-09-18 13:50:38 -05:00
Scott Lahteine	40d3e854f6	Remove redundant extern delta[]	2016-09-18 13:39:47 -05:00
Scott Lahteine	2ebfbc4c8d	Merge pull request #4836 from thinkyhead/rc_some_comments ... Some comments, const args, debug output tweaks	2016-09-18 13:38:07 -05:00
Scott Lahteine	e5505e3b33	Allow non-square leveling grid	2016-09-18 13:11:20 -05:00
Scott Lahteine	2fc9ad6657	Use const ref args in probe_pt	2016-09-18 12:58:43 -05:00
Scott Lahteine	2c2688d7ad	Adjust comments, spacing	2016-09-18 12:58:42 -05:00
Scott Lahteine	b9d19b0008	Tweak extrapolate_one_point	2016-09-18 12:58:42 -05:00
Scott Lahteine	3c0b591935	Fix nozzle position description	2016-09-18 12:58:42 -05:00
Scott Lahteine	18d8dd4c0f	set_current_from_steppers_for_axis const arg	2016-09-18 12:58:42 -05:00
Scott Lahteine	edfaf1c582	Stepper::report_positions patch	2016-09-18 12:58:42 -05:00
Scott Lahteine	d1f4c3d73b	Patch sync_plan_position comment	2016-09-18 12:58:41 -05:00
Scott Lahteine	0c25af30d4	Document homeaxis	2016-09-18 12:58:41 -05:00
Scott Lahteine	e7882e45e3	Document set_axis_is_at_home	2016-09-18 12:58:40 -05:00
Scott Lahteine	fef959c31a	Merge pull request #4834 from thinkyhead/rc_code_bool ... Standardize code_value_bool	2016-09-18 12:44:20 -05:00
Scott Lahteine	07ac9a1152	Merge pull request #4822 from blubbfish/patch-3 ... Tweak some german language strings	2016-09-18 11:38:22 -05:00
Scott Lahteine	661fe09ce7	Standardize code_value_bool	2016-09-18 11:32:32 -05:00
Scott Lahteine	20e5140e75	Merge pull request #4833 from thinkyhead/rc_no_scara_axis_scaling ... Remove SCARA axis_scaling	2016-09-18 11:31:50 -05:00
Scott Lahteine	a501f430eb	Enable M0/M1 with Emergency Parser	2016-09-18 11:14:10 -05:00
Philip Schell	cd8b22b527	Tweak some german language strings ... Change some string to get a better wording in german	2016-09-16 22:29:39 +02:00
Scott Lahteine	83a41c7ceb	Remove SCARA axis_scaling	2016-09-16 15:21:18 -05:00
Scott Lahteine	d41eeb62af	Merge pull request #4781 from thinkyhead/rc_final_z_correction ... Use simplified Z correction in G29 when possible	2016-09-16 15:14:19 -05:00
Scott Lahteine	502150046c	Merge pull request #4805 from thinkyhead/rc_config_adjustment ... Additional documentation of Configuration.h	2016-09-16 15:13:20 -05:00
Scott Lahteine	a1812b55f6	Space out array values	2016-09-16 14:41:05 -05:00
Scott Lahteine	d4599fd8ed	Comment patches to Configuration.h	2016-09-16 14:41:05 -05:00
Scott Lahteine	723e983073	Default EXTRUDE_MAXLENGTH to 200mm	2016-09-16 14:41:04 -05:00
Scott Lahteine	b08bd84f8e	Merge pull request #4806 from blubbfish/patch-2 ... Update language_de.h	2016-09-16 14:39:20 -05:00
darrelhunt	7b8bfa4358	Update pins_TEENSYLU.h	2016-09-16 11:26:37 -07:00
darrelhunt	829c8592f2	Update pins_TEENSY2.h	2016-09-16 11:26:09 -07:00
darrelhunt	e0aee20327	Update pins_SAV_MKI.h	2016-09-16 11:25:42 -07:00
darrelhunt	88d3fc0bcf	Update pins_PRINTRBOARD.h	2016-09-16 11:25:14 -07:00
darrelhunt	4277221abb	Update pins_BRAINWAVE_PRO.h	2016-09-16 11:24:32 -07:00
darrelhunt	b8ecbe9116	Update pins_BRAINWAVE.h	2016-09-16 11:23:52 -07:00
darrelhunt	60f757077e	Update pins_5DPRINT.h	2016-09-16 11:22:52 -07:00
Silvio Didonna	ff2b2d5939	Added missing translations	2016-09-16 01:17:58 +02:00
Philip Schell	2b11c3274c	Update language_de.h	2016-09-15 15:16:11 +02:00
Philip Schell	54e6d12382	Update language_de.h ... @MarlinFirmware/language-team updated german languagefile to the latest english version	2016-09-14 14:17:21 +02:00
Scott Lahteine	57564ae576	Use last probe point to correct Z when possible	2016-09-14 02:03:43 -05:00
Scott Lahteine	e40646de42	Merge pull request #4803 from thinkyhead/rc_lcd_button_fix ... Clear LCD button state, apply timer to all	2016-09-13 18:03:39 -05:00
Scott Lahteine	29f224594c	Fix some regressive typos in G29	2016-09-13 17:31:02 -05:00
Scott Lahteine	5ecc7d9f25	Clear LCD button state, apply timer to all ... Addressing #3007	2016-09-13 16:10:27 -05:00
Scott Lahteine	9b0931ef74	Apply fixed EXTRUDER_RUNOUT_PREVENT	2016-09-13 03:33:04 -05:00
Scott Lahteine	b1a60e8954	Reformat, rearrange, tweak, and document ... - Add comments to several functions - Add an option to use Fast SQRT for Delta IK - Group related functions together - Outdent some leveling-related functions	2016-09-13 03:33:04 -05:00
Scott Lahteine	61284cbd8c	Various code style adjustments	2016-09-13 03:33:04 -05:00
Scott Lahteine	788a16fc46	Clean up serial out code	2016-09-13 03:33:03 -05:00
Scott Lahteine	0e38bea79d	Shrink 3-point leveling code	2016-09-13 03:33:03 -05:00
Scott Lahteine	4f75ce6957	Unify reset_bed_level for linear/non-linear	2016-09-13 03:33:03 -05:00
Scott Lahteine	41d8149bce	Sanity check for more than 1 controller	2016-09-13 03:33:02 -05:00
Scott Lahteine	40785ce8ac	Use count method for kinematic sanity check	2016-09-13 03:33:02 -05:00
Scott Lahteine	3236762e07	Clean up sanity check for LCD_PROGRESS_BAR	2016-09-13 03:33:02 -05:00
Scott Lahteine	a9ed23225f	bed_level => bed_level_grid	2016-09-13 03:33:02 -05:00
Scott Lahteine	82be65065c	Fix up untilted_stepper_position and set_current_from_steppers_for_axis	2016-09-13 03:33:01 -05:00
Scott Lahteine	d65f5d816f	Patch to fix kinematics	2016-09-13 03:33:01 -05:00
Scott Lahteine	e529c6407e	Rename set_cartesian_from_steppers, cartesian_position	2016-09-13 03:33:01 -05:00
Scott Lahteine	c109399bf6	Fix planner leveling and rename arguments ... Use lx, ly, lz for “logical” positions	2016-09-13 03:33:01 -05:00
Scott Lahteine	d4f21af6b3	sync_plan_position_delta => sync_plan_position_kinematic	2016-09-13 03:33:01 -05:00
Scott Lahteine	acd1b6e9c0	Rename delta_grid spacing for general nonlinear	2016-09-13 03:33:00 -05:00
Scott Lahteine	c5fa70809b	Implement M0/M1 for EMERGENCY_PARSER	2016-09-13 03:33:00 -05:00
Scott Lahteine	786d1afb72	Add position_is_reachable, use in home_z_safely	2016-09-13 03:33:00 -05:00
Scott Lahteine	b4034915f8	Move z safe homing to its own function	2016-09-13 03:33:00 -05:00
Scott Lahteine	c84b14c77a	Move delta homing to its own function	2016-09-13 03:32:59 -05:00
Scott Lahteine	f9a192c7e3	Move setup() and loop() to the end	2016-09-13 03:32:59 -05:00
Scott Lahteine	8ff338c2b9	Patch stepper.h for SCARA	2016-09-13 03:32:59 -05:00
Scott Lahteine	74d7f5e57b	Patch SCARA example config	2016-09-13 03:32:59 -05:00
Scott Lahteine	6ab54c60b1	Add conditionals for kinematics, leveling	2016-09-13 03:32:59 -05:00
Scott Lahteine	21514568fd	Add enum for ALL_AXES	2016-09-13 03:32:58 -05:00
Scott Lahteine	413b61e64a	Add HYPOT2 and float comparison macros	2016-09-13 03:32:58 -05:00
Scott Lahteine	a6f6ed352b	Fix comment on FILAMENT_RUNOUT_SENSOR	2016-09-13 02:14:34 -05:00
Scott Lahteine	48e14d049a	Merge pull request #4710 from thinkyhead/rc_fix_leveling_maths ... Bed leveling that accounts for home XYZ	2016-09-10 15:47:39 -05:00
Scott Lahteine	416821a71c	Merge pull request #4765 from thinkyhead/rc_endstop_direction ... Sanitycheck endstop plugs based on homing direction	2016-09-10 14:49:50 -05:00
Scott Lahteine	9248cfb0ad	Bed leveling that accounts for home XYZ	2016-09-10 13:47:21 -05:00
Scott Lahteine	6ac9d895ca	Tweak Filament Width variables	2016-09-10 13:29:25 -05:00
Scott Lahteine	68ba45572e	Don't say "heating complete" unless done	2016-09-10 13:29:25 -05:00
Scott Lahteine	2bfc6fe1b0	Move XYZ constants closer to the top	2016-09-10 13:25:44 -05:00
Scott Lahteine	12b94e419f	Sanitycheck endstop plugs based on homing direction	2016-09-08 13:56:32 -05:00
Scott Lahteine	29c4f67a29	Additional path - followup to #4743	2016-09-07 15:08:12 -05:00
Robert Bartl	494d5770b8	makefile fix for arduino 1.6.9 unzipped	2016-09-03 19:45:27 -05:00
Scott Lahteine	6f71bd7372	Merge pull request #4754 from thinkyhead/rc_mixing_regression ... Unify counter_m and counter_M	2016-09-02 12:27:43 -05:00
Scott Lahteine	9bf78ef465	Fix capitalization of counter_m	2016-09-02 11:31:45 -05:00
Scott Lahteine	42b5616327	Try bool for direction instead of long	2016-09-02 11:28:48 -05:00
Scott Lahteine	cbe9ab902c	Merge pull request #4747 from thinkyhead/rc_sd_show_percent ... Option to show SD percent on Graphical LCD	2016-09-02 07:44:42 -05:00
Scott Lahteine	f20b2b21eb	Optimize LCD string/char printing	2016-09-02 06:41:24 -05:00
Scott Lahteine	3b2f7ba225	Merge pull request #4748 from thinkyhead/rc_sd_print_timer ... Patch duration_t toDigital method	2016-09-02 04:41:11 -05:00
Kai	445d8215e4	Option to show SD percent on Graphical LCD	2016-09-02 02:17:36 -05:00
Scott Lahteine	d07a913f21	Tweak to stepper advance e_steps update	2016-09-02 02:06:17 -05:00
Scott Lahteine	aaef7c6b89	Fix a misspelling of minimum	2016-09-02 01:42:38 -05:00
Scott Lahteine	ad659b5f91	Merge pull request #4725 from thinkyhead/rc_log_machine_info ... Log machine info in G28 and G29	2016-09-01 23:58:59 -05:00
Scott Lahteine	c6859a1e54	Handle hours >= 100	2016-09-01 23:54:48 -05:00
Kai	9f706a9635	Patch duration_t toDigital method	2016-09-01 23:34:15 -05:00
Scott Lahteine	c3caa42630	Merge pull request #4738 from thinkyhead/rc_ensure_floats ... Optimize stepper ISRs, plus cleanup, shorthand	2016-09-01 14:36:22 -05:00
Scott Lahteine	426f662586	Apply MINIMUM_STEPPER_PULSE in stepper advance_isr	2016-08-30 14:31:48 -05:00
Scott Lahteine	8c7ee4599e	Optimize stepper advance_isr	2016-08-30 14:31:48 -05:00
Scott Lahteine	9725bcd099	Minor "optimizations" in stepper ISR	2016-08-30 14:21:43 -05:00
Scott Lahteine	4ec3d1ea58	Add some commentary to stepper ISR	2016-08-30 14:21:15 -05:00
Scott Lahteine	d9bcc7bb45	Set a bool when a stepper block is done	2016-08-30 14:20:48 -05:00
Scott Lahteine	08f717e5f7	Use bit-size typedefs for some stepper vars	2016-08-30 14:19:49 -05:00
Scott Lahteine	d554c1dda8	Clean up planner kernel pass methods	2016-08-30 14:16:13 -05:00
Scott Lahteine	b2e5ec85d7	Add [XYZ]_CENTER conditionals	2016-08-30 14:15:41 -05:00
Scott Lahteine	7e20448a2d	Add HOMING_Z_WITH_PROBE conditional	2016-08-30 13:29:26 -05:00
Scott Lahteine	0e4107da34	Minor cleanup of homeaxis, etc.	2016-08-30 13:29:26 -05:00
Scott Lahteine	f1201e11c7	Improve the Jerk description	2016-08-29 12:39:21 -05:00
Scott Lahteine	3f038bef00	Heading for movement settings	2016-08-29 02:01:34 -05:00
Scott Lahteine	fd2269f489	Log machine info in G28 and G29	2016-08-28 20:48:28 -05:00
Scott Lahteine	6eaf4f4909	Fix spacing of debug output in homeaxis	2016-08-28 19:43:33 -05:00
Scott Lahteine	1e6d1c39ea	Improve verbiage of dropsegments sanity error	2016-08-28 19:40:32 -05:00
Scott Lahteine	0729a8f08d	Use the probe travel height for pre-probe move ... Instead of using the home_bump for Z to move close to the bed before doing a slow probe, use the probe travel height.	2016-08-28 19:13:08 -05:00
Scott Lahteine	dd94d0b9d5	Fix bed probing bug without PROBE_DOUBLE_TOUCH ... If `PROBE_DOUBLE_TOUCH` wasn't enabled, the probe move could be way too short! See #4701 for example.	2016-08-28 19:00:25 -05:00
Scott Lahteine	35a0c46f16	Tweak debug output for probe in G29	2016-08-28 18:44:44 -05:00
Scott Lahteine	a82a89bc58	Merge pull request #4722 from thinkyhead/rc_minimum_stepper_pulse ... MINIMUM_STEPPER_PULSE option	2016-08-28 10:03:32 -05:00
Scott Lahteine	a2572d2854	Fix Danish encoding and an error message	2016-08-28 09:51:06 -05:00
Scott Lahteine	759234af60	MINIMUM_STEPPER_PULSE option	2016-08-27 23:58:40 -05:00
Scott Lahteine	2cb63f0bf7	Merge pull request #4719 from thinkyhead/rc_delta_homing_patch ... Marlin patches for homing, esp. Delta	2016-08-27 20:46:50 -05:00
Scott Lahteine	8241cf9901	Merge pull request #4720 from thinkyhead/rc_allow_stepper_omission ... Patch stepper.cpp to allow omitting steppers	2016-08-27 20:36:22 -05:00
Scott Lahteine	7e893f4309	Merge pull request #4721 from thinkyhead/rc_temperature_isr_comments ... Rc temperature isr comments	2016-08-27 20:36:03 -05:00
Scott Lahteine	73d86098b7	Marlin patches for homing, esp. Delta	2016-08-27 20:32:05 -05:00
Scott Lahteine	338bc768b1	Merge pull request #4717 from thinkyhead/rc_log_the_probe ... Debug logging of nozzle type and offsets	2016-08-27 20:24:19 -05:00
Scott Lahteine	fae92e3f3c	Merge pull request #4718 from thinkyhead/rc_twibus_patch_20160827 ... TWIBus patch for proper use of Wire.requestFrom	2016-08-27 20:22:53 -05:00
Scott Lahteine	a485a19052	Added optional planner logging	2016-08-27 20:12:22 -05:00
Scott Lahteine	e9bfca5870	Additional comments for Temperature::isr	2016-08-27 20:12:22 -05:00
Scott Lahteine	a255945f29	Add DEBUG_ALL enum	2016-08-27 20:12:22 -05:00
Scott Lahteine	a28e15399f	Patch stepper.cpp to allow omitting steppers	2016-08-27 20:11:17 -05:00
Scott Lahteine	2b226bc5c2	TWIBus patch for proper use of Wire.requestFrom	2016-08-27 20:09:28 -05:00
Scott Lahteine	d641344d3a	Remove redundant probe offset in homing	2016-08-27 19:58:56 -05:00
Scott Lahteine	fb19a3cdec	Merge pull request #4649 from thinkyhead/rc_boelle_danish_update ... Danish update (18 Aug 2016)	2016-08-27 19:06:05 -05:00
Scott Lahteine	00638131e5	Debug logging of nozzle type and offsets	2016-08-27 15:21:01 -05:00
Scott Lahteine	8e9ac72191	Merge pull request #4709 from thinkyhead/rc_log_the_reason ... Log whether homing with probe or endstop	2016-08-26 17:05:55 -05:00
Scott Lahteine	991a34aff2	Log whether homing with probe or endstop	2016-08-26 15:50:10 -05:00
Scott Lahteine	3b93b79f5c	Merge pull request #4703 from bgort/RCBugFix ... Add note suggesting RAMBo users use the RAMBo board type or platformio environment	2016-08-26 14:53:56 -05:00
Scott Lahteine	00cdb15cec	Move invariant LCD strings to language.h	2016-08-26 02:48:57 -05:00
Bo Herrmannsen	d2ae5b00d9	Danish up to date (18 Aug 2016)	2016-08-26 02:48:57 -05:00
Scott Lahteine	e78274a7f4	Consistent order/formatting of pins files	2016-08-25 20:59:45 -05:00
Scott Lahteine	11e9530111	Properly handle probe pin for BQ printers	2016-08-25 20:59:44 -05:00
Scott Lahteine	1968983f35	Move PROBE_SELECTED to an earlier point	2016-08-25 20:59:44 -05:00
Brian	2fae32f35f	Add note suggesting RAMBo users use the RAMBo board type or platformio environment; ... Add note that Viki 2.0 wiring diagram v1.2 has a mistake in it;	2016-08-25 15:05:29 -04:00
esenapaj	1749a7fae3	Suppress warning	2016-08-24 00:18:06 +09:00
Scott Lahteine	d07d85ac9f	Ensure probe points at the delta edge are kept	2016-08-23 05:09:56 -05:00
AnHardt	7e36b76af2	Repair MarlinSerial with TX-buffer ... These '{' are important to avoid the redefinition of `unsigned char _sreg = SREG;` at the same level. Used in ``` #define CRITICAL_SECTION_START unsigned char _sreg = SREG; cli(); ```	2016-08-22 23:40:09 +02:00
Gege2B	1e65f1a1d8	Update french language	2016-08-22 12:46:58 -05:00
Scott Lahteine	ab59280075	MIN_SEGMENTS_FOR_MOVE => MIN_STEPS_PER_SEGMENT ... Follow-up to #4666	2016-08-21 08:56:03 -05:00
Scott Lahteine	27b80b1dd1	Merge pull request #4667 from thinkyhead/rc_M211_sw_endstop_switch ... M211: Enable/Disable Software Endstops	2016-08-21 06:44:00 -05:00
Scott Lahteine	14a03727e1	Tweak serialprintPGM	2016-08-21 00:10:09 -05:00
Scott Lahteine	2f223b8c79	Use ABC and XYZ for "3"	2016-08-21 00:10:08 -05:00
Scott Lahteine	4cd1ad8f28	Adjustments to M209, G28, M605	2016-08-21 00:10:08 -05:00
Scott Lahteine	e354cf5884	Apply sw_endstops_enabled to manual move	2016-08-21 00:10:08 -05:00
Scott Lahteine	280534c06f	Add M211: Enable/Disable Software Endstops	2016-08-21 00:10:08 -05:00
Scott Lahteine	01d4703429	PREVENT_DANGEROUS_EXTRUDE => PREVENT_COLD_EXTRUSION ... Also improve the documentation of this and related options, and set EXTRUDE_MINTEMP to 170 everywhere.	2016-08-20 23:35:27 -05:00
Scott Lahteine	a1f6cf1e5d	Merge pull request #4665 from thinkyhead/rc_lcd_not_ultipanel ... Clean up ultralcd code, dependencies on ULTIPANEL	2016-08-20 22:43:17 -05:00
Scott Lahteine	1a255afa36	Merge pull request #4666 from thinkyhead/rc_dropsegments_adj ... dropsegments => MIN_SEGMENTS_FOR_MOVE	2016-08-20 22:42:16 -05:00
Scott Lahteine	374f8d2014	dropsegments => MIN_SEGMENTS_FOR_MOVE	2016-08-20 18:52:15 -05:00
Scott Lahteine	76c3f326ff	Clean up DOGM code, comments	2016-08-20 18:33:12 -05:00
Scott Lahteine	71319adbb8	Wrap ULTIPANEL-dependent code	2016-08-20 18:33:11 -05:00
Scott Lahteine	305913545e	Move number-to-string function to utility.*	2016-08-20 18:33:11 -05:00
Scott Lahteine	394c80c87b	Merge pull request #4655 from thinkyhead/rc_serial_static ... Optimize, reduce size of MarlinSerial	2016-08-20 15:51:57 -05:00
MagoKimbra	28d1e5a946	Fix_Zig_Zag	2016-08-20 11:28:08 +02:00
Scott Lahteine	14395a1a96	Optimize, reduce size of MarlinSerial	2016-08-19 16:53:20 -05:00
Scott Lahteine	4d4c00d69c	Merge pull request #4651 from thinkyhead/rc_homing_vs_leveling_z ... Improvements to homing / leveling	2016-08-19 15:45:49 -05:00
Brian Gortney	8fae3e1f9f	Add Rambo support/env to platformio.ini; properly maps extended pins	2016-08-19 07:11:23 -04:00
Scott Lahteine	12d72363cb	Do Delta radius check without sqrt	2016-08-19 05:05:48 -05:00
Scott Lahteine	044f800be9	Use SERIAL_PROTOCOLLNPGM in G28	2016-08-19 04:45:33 -05:00
Scott Lahteine	d309a9647d	Include probe offset for moving "close to the bed"	2016-08-19 04:45:33 -05:00
Scott Lahteine	35a08eeaeb	Use Z_HOME_DIR over axis_home_dir where we can	2016-08-19 04:45:32 -05:00
Scott Lahteine	99b22d5785	Default AUTO_BED_LEVELING_GRID_POINTS to 3	2016-08-19 04:45:32 -05:00
Scott Lahteine	9b1f3f7d12	Sanity-check DELTA + AUTO_BED_LEVELING_GRID_POINTS	2016-08-19 04:45:32 -05:00
Scott Lahteine	733453569b	Merge pull request #4650 from thinkyhead/rc_percent_is_percent ... extruder_multiplier => flow_percentage	2016-08-19 04:38:18 -05:00
Scott Lahteine	55355a4fb8	Make probed points more symmetrical	2016-08-19 04:32:03 -05:00
Scott Lahteine	1f776f6034	Tweak some code comments	2016-08-19 04:32:02 -05:00
Scott Lahteine	748228cf40	Use named indices for delta_grid_spacing	2016-08-19 04:32:02 -05:00
Scott Lahteine	ead333e7da	line_to_axis_pos => do_homing_move	2016-08-19 04:32:02 -05:00
Scott Lahteine	7a4ccd7967	Add do_probe_move with Z fixes	2016-08-19 04:32:02 -05:00
Scott Lahteine	a1bad589c9	Augment debug/homing logging	2016-08-19 04:32:02 -05:00
Scott Lahteine	41b5c48129	Update software endstops if EEPROM is loaded	2016-08-19 04:32:01 -05:00
Scott Lahteine	628dcbc764	extruder_multiplier => flow_percentage	2016-08-18 22:13:47 -05:00
Jason Westervelt	d222ee4de2	Update language_ru.h ... Updated missing translations. Caught up on change to MSG_HOME.	2016-08-17 13:55:44 -07:00
Scott Lahteine	d63b8e2b2b	Additional details for I2C_SLAVE_ADDRESS	2016-08-15 19:27:53 -07:00
Scott Lahteine	7427290d3a	Merge pull request #4634 from thinkyhead/rc_lang_disp_char ... Set language display charset in language.h	2016-08-15 19:25:56 -07:00
Scott Lahteine	aa30550b21	Keep SIMULATE_ROMFONT only language.h	2016-08-15 19:11:31 -07:00
Scott Lahteine	cec61c350d	Set language display charset in language.h	2016-08-15 19:01:12 -07:00
Scott Lahteine	165d7abb1b	Merge pull request #4625 from thinkyhead/rc_i2c_request_capture_flush ... Add request, capture, flush to TWIBus	2016-08-15 18:15:43 -07:00
RicardoGA	507784b846	Fix Messages length	2016-08-15 10:30:51 -05:00
Scott Lahteine	bd928a69ec	Add request, capture, flush to TWIBus	2016-08-15 00:04:20 -07:00
RicardoGA	7b7f319ed5	Update Spanish Lenguage ... Adds missing messages	2016-08-14 23:30:43 -05:00
Scott Lahteine	132322e4d9	Fix #4614: currentScreen only defined with ULTIPANEL	2016-08-14 00:29:46 -07:00
Scott Lahteine	dcd26b0403	Merge pull request #4621 from thinkyhead/rc_fan_set_output ... Init PWM-able AUTO_FAN pins with SET_OUTPUT	2016-08-13 21:22:27 -07:00
Scott Lahteine	79ba983782	Allow reply() to use const string with no warning	2016-08-13 21:05:44 -07:00
Scott Lahteine	3a0a94b21a	Always init configured fan pins	2016-08-13 20:38:40 -07:00
Scott Lahteine	c63003ed3e	Use matching auto-fan flags	2016-08-13 20:38:40 -07:00
Scott Lahteine	3475fd7b0f	Init PWM-able auto fan pins with SET_OUTPUT	2016-08-13 20:38:40 -07:00
Scott Lahteine	abf9696db1	Loop fan-pins based on array size	2016-08-13 20:05:32 -07:00
Scott Lahteine	e88575c8ec	Init next_auto_fan_check_ms to zero	2016-08-13 20:05:32 -07:00
Scott Lahteine	7272ec5608	Update HAS_FAN flags for 4 auto fans	2016-08-13 20:05:32 -07:00
Scott Lahteine	7b21811a9a	Flags for matching auto-fans	2016-08-13 20:05:32 -07:00
Scott Lahteine	97e0aed304	Further refinements of TWIBus	2016-08-13 18:32:41 -07:00
Scott Lahteine	38fa1b1939	Merge pull request #4196 from cimbalo/Platformio_support ... Add working PlatformIO support	2016-08-12 17:32:09 -07:00
Scott Lahteine	d7edc039af	Merge pull request #4605 from thinkyhead/rc_3drag_fan_is_8 ... Fixup 3DRAG pins based on updated RAMPS pins	2016-08-12 17:30:27 -07:00
Silvio	923388e0c7	Fix acceleration and feedrate following bq/Marlin	2016-08-12 15:42:20 +02:00
Scott Lahteine	405afec393	Include decimeters in filamentUsed display	2016-08-12 05:16:43 -07:00
Scott Lahteine	fef0e8ba86	Merge pull request #4610 from thinkyhead/rc_sd_pause_and_stop ... Fix stopSDPrint so it works when paused	2016-08-12 04:09:22 -07:00
Scott Lahteine	192ac2dfd7	Squish some CardReader code	2016-08-12 03:32:42 -07:00
Scott Lahteine	61932b859e	Fix bug in CardReader::stopSDPrint ... If the SD print is paused, it cannot be stopped	2016-08-12 03:21:10 -07:00
Scott Lahteine	9e5d5a3b7c	Merge pull request #4597 from tnw513/italian_fix ... Added hyphenated strings for full graphic display	2016-08-12 02:37:53 -07:00
Silvio Didonna	f999292eea	added hyphenated letters for full graphic display and fixed some strings	2016-08-12 08:57:22 +02:00
Scott Lahteine	67f119d18b	Add an i2c request handler	2016-08-11 18:09:18 -07:00
Scott Lahteine	2d3db5b5bd	Fixup pins_3DRAG based on updated RAMPS pins	2016-08-11 15:49:47 -07:00
Scott Lahteine	d29a64d4b3	Merge pull request #4603 from thinkyhead/rc_less_MSG_MOVE ... Strip never-translated strings from language files	2016-08-11 14:21:58 -07:00
Scott Lahteine	d6a7ca6553	Merge pull request #4584 from thinkyhead/rc_delta_cal_more ... Use configured feedrates, center in DELTA_CALIBRATION_MENU	2016-08-11 14:04:05 -07:00
Scott Lahteine	d3b432adca	Strip never-translated strings from language files	2016-08-11 13:41:07 -07:00
Scott Lahteine	1a558ef486	Tweak MarlinSerial precursor	2016-08-11 12:47:06 -07:00
Scott Lahteine	802818f7ab	Cleanup SdFatUtil.h	2016-08-11 12:47:06 -07:00
Scott Lahteine	52560e257f	Merge pull request #4595 from thinkyhead/rc_i2c_slave ... Add support for i2c slave address	2016-08-11 12:39:26 -07:00
Scott Lahteine	432e9a1f50	Use configured feedrates, center for DELTA_CALIBRATION_MENU	2016-08-11 12:05:55 -07:00
Scott Lahteine	cd496dd9bd	do_blocking_move_to can't be 'inline', takes const ref args	2016-08-11 12:05:55 -07:00
Scott Lahteine	dd75fca4d9	Make M155 / M156 a bit more flexible	2016-08-11 00:52:01 -07:00
Scott Lahteine	a99ecf71d8	Add support for i2c slave address	2016-08-10 23:30:35 -07:00
Scott Lahteine	b63d70b186	Fix serial output for MBL, M303	2016-08-10 18:49:52 -07:00
Scott Lahteine	a36a168af2	Use the truly configured middle on Delta	2016-08-10 00:03:22 -07:00
Scott Lahteine	58c8e6cef2	Fixes #4576: Convert filamentUsed to long for display	2016-08-09 23:57:28 -07:00
Scott Lahteine	01f1f779a5	Followup to #4574, specify L for long	2016-08-09 23:43:37 -07:00
Kaibob2	1c7bd17e60	Update language_de.h with MSG_MOVE_E1 - E4 ... MSG_MOVE_E1 was missing MSG_MOVE_E2 was missing MSG_MOVE_E3 was missing MSG_MOVE_E4 was missing I assigned "0" to "MSG_MOVE_E1", "1" to "MSG_MOVE_E2" and so on, as this is what i assume to be the standard naming for the first (E0) and second (E1) extruder. This would have to be changed inthe other languages too :(	2016-08-09 20:49:26 +02:00
Scott Lahteine	880cdb553b	Include days in Graphical LCD print timer	2016-08-08 23:21:36 -07:00
Scott Lahteine	f4ac8c15e3	Merge pull request #4573 from thinkyhead/rc_mintemp_bed_later ... Throw MINTEMP BED error only if heating	2016-08-08 23:02:42 -07:00
Scott Lahteine	b7b5b50a84	Throw bed min temp error only if heating	2016-08-08 22:49:22 -07:00
Scott Lahteine	d3ba878f70	Drop intermediate float in HEATER_0_USES_MAX6675 test	2016-08-08 22:49:22 -07:00
Scott Lahteine	3e8f9ecd1c	Extend min/max_temp_error for the bed	2016-08-08 22:49:21 -07:00
Scott Lahteine	1f15f0df5f	Merge pull request #4572 from thinkyhead/rc_digital_clock_100h ... Show up to 99:59 in digital time	2016-08-08 22:28:29 -07:00
Scott Lahteine	8100a4dace	Fix a compile error in EMERGENCY_PARSER sanity check	2016-08-08 21:49:57 -07:00
Scott Lahteine	45f67164b6	Simplify the delay in kill()	2016-08-08 21:49:34 -07:00
Scott Lahteine	30b1c731b5	Show up to 99:59 in digital time	2016-08-08 21:26:34 -07:00
Scott Lahteine	3be4511230	Patch command order in delta calibration menu	2016-08-08 21:15:25 -07:00
Scott Lahteine	9afa060ed6	Merge pull request #4570 from thinkyhead/rc_proper_delta_calibration ... Make DELTA_CALIBRATION_MENU more universal	2016-08-08 21:11:40 -07:00
Scott Lahteine	46c8862635	Merge pull request #4564 from AnHardt/max-spi-setup ... MISO is an input	2016-08-08 21:01:15 -07:00
Scott Lahteine	88540d8ecf	Fix: LCD displays SD status at startup	2016-08-08 20:53:18 -07:00
Scott Lahteine	b16ea09498	Make DELTA_CALIBRATION_MENU more universal	2016-08-08 20:42:58 -07:00
Scott Lahteine	3a56836ead	Always disable SLOWDOWN for DELTA/SCARA	2016-08-08 18:06:46 -07:00
AnHardt	aa9b52b2e7	MISO is an input	2016-08-08 20:09:57 +02:00
Scott Lahteine	67c4acf750	Merge pull request #4562 from thinkyhead/rc_fix_z_dual_endstops ... Fix Z_DUAL_ENDSTOPS with Z MIN Homing	2016-08-07 19:23:09 -07:00
Scott Lahteine	e113740fa3	Specify that Z_PROBE_*_HEIGHT is nozzle-relative	2016-08-07 17:54:17 -07:00
Scott Lahteine	462e189edd	Move pullups after Z_DUAL_ENDSTOPS block	2016-08-07 17:43:02 -07:00
Scott Lahteine	367dad5902	Sanity check Z_DUAL_ENDSTOPS with DELTA	2016-08-07 17:08:41 -07:00
Scott Lahteine	5fca110e0d	Fix Z_DUAL_ENDSTOPS with MIN homing	2016-08-07 17:08:41 -07:00
Scott Lahteine	fc11f05c11	Merge pull request #4556 from thinkyhead/rc_all_feedrates_mm_s ... Within Marlin, maintain most feed rates in mm/s	2016-08-07 16:14:16 -07:00
Scott Lahteine	7b2abe6fc8	Use steps_to_mm in extruder runout prevent	2016-08-07 00:28:52 -07:00
Scott Lahteine	d320065320	Within Marlin, maintain most feed rates in mm/s	2016-08-07 00:28:52 -07:00
Scott Lahteine	ed0b50ebee	Merge pull request #4555 from thinkyhead/rc_mbl_index_rounding ... Remove premature int-cast from MBL cell index methods	2016-08-06 23:34:01 -07:00
Scott Lahteine	bad286d52f	Save CPU by multiplying by pre-compiled values	2016-08-06 23:24:07 -07:00
Scott Lahteine	dce6026e0e	Remove premature cast to int	2016-08-06 23:01:29 -07:00
Scott Lahteine	cffe77c537	Merge pull request #4553 from thinkyhead/rc_lcd_chars_save_ram ... Save bytes for custom chars (Hitachi LCD)	2016-08-06 18:29:16 -07:00
Scott Lahteine	42927530fe	Explicitly clear the screen in lcd_goto_screen	2016-08-06 18:10:39 -07:00
Scott Lahteine	a6d2c2479f	Minor cleanup of lcd_goto_screen calls	2016-08-06 18:10:39 -07:00
Scott Lahteine	e47c8b9829	Save bytes for custom chars (Hitachi LCD)	2016-08-06 18:10:39 -07:00
Scott Lahteine	0ff5005c9b	Allow connector flexibility for BQ ZUM Mega	2016-08-06 17:19:12 -07:00
Scott Lahteine	98437bd488	Allow override of CONTROLLERFAN_PIN with RAMPS EFF	2016-08-06 17:19:12 -07:00
Scott Lahteine	93eafa1785	Use DISABLED to check TEENSY pin option	2016-08-06 17:19:12 -07:00
AnHardt	98392abb78	Clean warnings for pins_BQ_ZUM_MEGA_3D.h	2016-08-06 17:19:12 -07:00
AnHardt	98e96feee9	Repair SPI-pins ... SCK_PIN can't be defined as DIO[number] they mus be defined as pure number. So rebuilding the structure of fastio.h in pins.h.	2016-08-06 17:19:11 -07:00
Scott Lahteine	a00783c41f	Format probe stowed test code	2016-08-06 14:31:07 -07:00
AnHardt	f37e8a31d7	Make Allen Key Probe stow ... by switching off the tests for the probe before the stow move.	2016-08-06 14:30:38 -07:00
Scott Lahteine	5347f39fce	Merge pull request #4542 from AnHardt/rep-de ... Repair-language.de	2016-08-05 23:50:35 -07:00
Scott Lahteine	5ef4a5577c	Merge pull request #4537 from thinkyhead/rc_fix_some_flaws ... Patch up some flaws here and there	2016-08-05 23:49:57 -07:00
AnHardt	0d3b67a580	Repair-language.de	2016-08-06 01:00:40 +02:00
Scott Lahteine	938e6d15c4	Patch up some flaws, here and there	2016-08-05 08:17:37 -07:00
Scott Lahteine	3a3984e67a	Merge pull request #4535 from thinkyhead/rc_old_symbols_first ... Move tests for old symbols to the top of sanity check	2016-08-04 21:24:02 -07:00
Scott Lahteine	d7b882e430	Move tests for old symbols to the top of sanity check	2016-08-04 21:03:55 -07:00
Scott Lahteine	479107d04f	Merge pull request #4530 from Kaibob2/patch-1 ... Added / Update language_de.h	2016-08-04 16:58:50 -07:00
Kaibob2	1abd7fa670	Update language_de.h ... Added german translation for MSG_INFO_PRINT_LONGEST and MSG_INFO_PRINT_FILAMENT. MSG_HEATING_COMPLETE changed from "Aufgeheizt" to "Extr. aufgeheizt" MSG_HEATING changed from "Aufheizen" to "Extr. aufheizen"	2016-08-04 09:40:38 +02:00
Scott Lahteine	7e2bd9a233	Z_RAISE_PROBE_* => Z_PROBE_*_HEIGHT	2016-08-03 21:18:38 -07:00
Scott Lahteine	445458c221	Don't include zprobe_zoffset in do_probe_raise	2016-08-03 21:12:02 -07:00
Rafa Couto	0114676953	Update of Galician language 2016-08-03	2016-08-03 15:00:18 +02:00
Scott Lahteine	bd7a96ed42	Merge pull request #4517 from thinkyhead/rc_min_probe_pin ... Define Z_MIN_PROBE_PIN always, allowing override	2016-08-02 21:35:59 -07:00
Scott Lahteine	704ae1b737	Merge pull request #4516 from thinkyhead/rc_short_prints_quiet ... Only report finished prints longer than 1 min	2016-08-02 21:14:30 -07:00
Scott Lahteine	7ed70305df	Merge pull request #4515 from thinkyhead/rc_fix_speaker_tone ... Prevent the 'tone(f,d)' function from being interrupted	2016-08-02 21:13:47 -07:00
Scott Lahteine	f1be87a85c	Move probe pin sanity checks out of ABL block	2016-08-02 20:55:17 -07:00
Scott Lahteine	9cb596e88c	Define Z_MIN_PROBE_PIN always, allowing override	2016-08-02 20:31:44 -07:00
Scott Lahteine	229f70f194	Only report finished prints longer than 1 min	2016-08-02 19:58:12 -07:00
Scott Lahteine	e040e00ae9	Merge pull request #4514 from thinkyhead/rc_cleanup_circularqueue ... Patch up CircularQueue	2016-08-02 19:42:38 -07:00
Scott Lahteine	6110d57c16	Prevent the 'tone(f,d)' function from being interrupted	2016-08-02 19:37:47 -07:00
Scott Lahteine	b73203a0b7	Move some includes around to uncover missing deps	2016-08-02 19:37:46 -07:00
Scott Lahteine	f26d5425bf	Patch up CircularQueue ... - Use `size` and `count` instead of `length` and `size` - Fix bug: `peek` should return the item - Clean up comments, spacing, spelling	2016-08-02 18:57:15 -07:00
Scott Lahteine	c9123adc59	Improved SCREEN / MENU macros	2016-08-02 18:05:34 -07:00
Scott Lahteine	cebeb48005	Merge pull request #4511 from thinkyhead/rc_encoder_flex ... Allow encoder pulse/step override for more LCDs	2016-08-02 16:50:50 -07:00
Scott Lahteine	3cccaa9885	Allow encoder pulse/step override for more LCDs	2016-08-02 15:57:26 -07:00
Scott Lahteine	14c5a46ee9	Use multiplication for MMM_SCALED	2016-08-02 15:05:17 -07:00
Scott Lahteine	d8945e8464	Fix Z_HEAD index for COREYZ	2016-08-02 15:05:17 -07:00
Scott Lahteine	0f030aface	Merge pull request #4503 from AnHardt/fix-retract ... Correct typo in retract()	2016-08-02 15:04:55 -07:00
Scott Lahteine	fbd8f06951	Merge pull request #4506 from thinkyhead/rc_buzzer_needs_beeper ... Buzzer requires BEEPER_PIN	2016-08-02 14:40:43 -07:00
Scott Lahteine	330f82971b	Buzzer requires BEEPER_PIN	2016-08-02 14:05:37 -07:00
Scott Lahteine	e0d7b8bf27	Fix Azteeg X3 servo pin / Viki i2c	2016-08-02 14:05:37 -07:00
Scott Lahteine	7cceb15925	Merge pull request #4505 from thinkyhead/rc_auto_select_dplugs ... Auto-select power plugs for RAMPS derivatives	2016-08-02 12:56:52 -07:00
Scott Lahteine	593b37519a	Boards with 4 power outputs are EFBF or EFBE	2016-08-02 12:34:28 -07:00
AnHardt	9ab94bd2c1	fix-babysrepping	2016-08-02 21:06:42 +02:00
AnHardt	39c4603598	Correct typo in retract.	2016-08-02 21:06:08 +02:00
Scott Lahteine	cebd2bfff0	Auto-select power plugs for RAMPS derivatives	2016-08-02 11:59:25 -07:00
Scott Lahteine	34c60f1b55	Merge pull request #4491 from thinkyhead/rc_fix_lcd_move_e ... Use a default argument in _lcd_move_e	2016-08-01 16:45:25 -07:00
Scott Lahteine	38af251b91	Use a default argument in _lcd_move_e	2016-08-01 16:09:26 -07:00
Scott Lahteine	374ae6c099	Fix pins for RAMBO plus VIKI	2016-08-01 16:09:26 -07:00
Scott Lahteine	7594138740	Merge pull request #4493 from jbrazio/buildroot-cleanup ... Move font folder	2016-08-01 15:57:23 -07:00
Scott Lahteine	6eed37aafb	Merge pull request #4486 from thinkyhead/rc_pid_add_extrusion_rate_off ... PID_EXTRUSION_SCALING, disabled by default	2016-07-31 18:23:51 -07:00
Scott Lahteine	4bf3526d00	Merge pull request #4463 from thinkyhead/rc_azteeg_x3_eeb ... Wrangle RAMPS variants and derivatives	2016-07-31 18:22:49 -07:00
Scott Lahteine	1993c45759	Merge pull request #4487 from thinkyhead/rc_refresh_pos_fix ... Update refresh_positioning - no need for obj ref	2016-07-31 18:22:38 -07:00
Scott Lahteine	f83369b79c	Update refresh_positioning - no need for obj ref	2016-07-31 18:01:13 -07:00
Scott Lahteine	63fd1f49a6	PID_EXTRUSION_SCALING, disabled by default	2016-07-31 17:49:34 -07:00
Scott Lahteine	49997e2e22	HI_VOLT_PIN => "RAMPS_Dn_PIN"	2016-07-31 15:42:52 -07:00
AnHardt	60ad365e21	repair-software-spi	2016-07-31 15:50:42 +02:00
Scott Lahteine	f388beafa1	Merge pull request #4476 from otvald/RCBugFix ... FIX for endstop adjustemt on delta is offset	2016-07-31 01:09:54 -07:00
Scott Lahteine	3633d4978b	Merge pull request #4475 from esenapaj/Fix-for-PR-#4452 ... Fix for PR #4452 (Additional heater-state output changes)	2016-07-31 01:08:27 -07:00
Thomas Otvald Jensen	fe059f1221	During homing, line_to_axis_pos will make a path which moves across the ... endstop trigger point. The move is stopped at endstop, so current_position should also be adjusted to reflect this! Caused error in subsequent call in endstop adjustment, since the movement would assume a wrong starting position.	2016-07-30 16:50:31 +02:00
esenapaj	bd73e6d3c8	Fix for PR #4452 (Additional heater-state output changes) ... ・Add missing ';'	2016-07-30 22:49:30 +09:00
esenapaj	cd5b03d88f	Update distribution date and readme	2016-07-30 21:27:29 +09:00
Scott Lahteine	f575e92f2e	Merge pull request #4473 from esenapaj/Follow-up-the-PR-#4408-etc ... Follow-up the PR #4408 (Add support for reprapworld LCD), etc	2016-07-30 04:45:27 -07:00
esenapaj	657ef8aded	Follow-up the PR #4408 (Add support for reprapworld LCD), etc ... ・Put #define REPRAPWORLD_GRAPHICAL_LCD into all the example configuration files ・Adjust spacing	2016-07-30 20:32:57 +09:00
Scott Lahteine	83d341c394	Make Conditionals.h a catch-all for old configs	2016-07-30 04:25:30 -07:00
Scott Lahteine	de951c64f1	Make pins for EFF a consistent order	2016-07-30 04:17:21 -07:00
Scott Lahteine	49f75b7891	pins_RAMPS_14.h => pins_RAMPS.h	2016-07-30 04:17:21 -07:00
Scott Lahteine	d3b713cebc	Set flags for RAMPS "type" in pins.h	2016-07-30 04:17:21 -07:00
Scott Lahteine	223b7e473f	RAMPS assignment for derivatives	2016-07-30 04:17:21 -07:00
Scott Lahteine	3865843283	Consolidate setting of RAMPS High Voltage PWM outputs	2016-07-30 04:17:21 -07:00
Scott Lahteine	bdac2eb13a	Don't set non-existent SLED_PIN	2016-07-30 04:17:21 -07:00
Scott Lahteine	bfbd01e29a	Merge pull request #4470 from thinkyhead/rc_fix_manual_move ... Followup to #4468	2016-07-30 04:17:05 -07:00
Scott Lahteine	802d873fc1	Merge pull request #4469 from esenapaj/Fix-for-PR-#4453 ... Fix for PR #4453 (Improved MANUAL_[XYZ]_HOME_POS)	2016-07-30 04:08:54 -07:00
Scott Lahteine	8e2f095dde	Merge pull request #4456 from jbrazio/speaker-type3 ... Improvement to non-blocking speaker	2016-07-30 04:07:08 -07:00
Scott Lahteine	ad68b4cb8b	Followup to #4468	2016-07-30 03:49:42 -07:00
esenapaj	b8c112c490	Fix for PR #4453 (Improved MANUAL_[XYZ]_HOME_POS)	2016-07-30 19:37:43 +09:00
Scott Lahteine	2f76138645	Merge pull request #4468 from thinkyhead/rc_fix_manual_move ... Specify manual-movable E axes by extruder type	2016-07-30 03:21:43 -07:00
Scott Lahteine	696b63e300	Specify manual-movable E axes by extruder type	2016-07-30 00:36:48 -07:00
Scott Lahteine	46c33f1cfa	Merge pull request #4467 from jbrazio/safe_delay-millis_t ... Makes safe_delay() to be fully compatible with delay()	2016-07-29 20:23:44 -07:00
Scott Lahteine	9e21b2e51d	Merge pull request #4455 from AnHardt/double-bump-feature ... double bump probing as a feature	2016-07-29 20:00:10 -07:00
Scott Lahteine	db4d03bc81	Merge pull request #4452 from thinkyhead/rc_fix_heaterstates_part_2 ... Additional heater-state output changes	2016-07-29 19:58:00 -07:00
Scott Lahteine	c68ca95345	Merge pull request #4464 from thinkyhead/rc_fix_steps_per_mm_handling ... Account for DELTA in Planner::refresh_positioning	2016-07-29 19:34:59 -07:00
João Brázio	226e74a438	Fixes safe_delay() to be fully compatible with delay()	2016-07-30 02:56:26 +01:00
João Brázio	8e79e8cdb3	Adds types.h	2016-07-30 02:55:52 +01:00
Scott Lahteine	844a4e799e	Account for DELTA in Planner::refresh_positioning	2016-07-29 18:41:11 -07:00
AnHardt	7188ce0ad6	double bump probing as a feature ... Why double touch probing is not a good thing. It's widely believed we can get better __probing__ results when using a double touch when probing. Let's compare to double touch __homing__. Or better let's begin with single touch __homing__. We home to find out out position, so our position is unknown. To find the endstop we have to move into the direction of the endstop. The maximum way we have to move is a bit longer than the axis length. When we arrive at the endstop - when it triggers, the stepper pulses are stopped immediately. It's a sudden stop. No smooth deacceleration is possible. Depending on the speed and the moving mass we lose steps here. Only if we approached slow enough (below jerk speed?) we will not lose steps. Moving a complete axis length, that slow, takes for ever. To speed up homing, we now make the first approach faster, get a guess about our position, back up a bit and make a second slower approach to get a exact result without losing steps. What we do in double touch probing is the same. But the difference here is: a. we already know where we are b. if the first approach is to fast we will lose steps here to. But this time there is no second approach to set the position to 0. We are measuring only. The lost steps are permanent until we home the next time. So if you experienced permanently rising values in M48 you now know why. (Too fast, suddenly stopped, first approach) What can we do to improve probing? We can use the information about our current position. We can make a really fast, but deaccelerated, move to a place we know it is a bit before the trigger point. And then move the rest of the way really slow.	2016-07-30 03:00:49 +02:00
Scott Lahteine	c31f56a38c	Deprecate EXTRUDER_WATTS and BED_WATTS	2016-07-29 17:34:14 -07:00
Scott Lahteine	e1970b4b28	Show power output in same order as temp output	2016-07-29 14:55:22 -07:00
Scott Lahteine	74df828acc	Show ADC values inline rather than after	2016-07-29 14:55:18 -07:00
João Brázio	2b5faa61e2	Consolidates Buzzer and Speaker into a single object	2016-07-29 19:25:39 +01:00
João Brázio	8093c5f534	Non-blocking speaker now uses arduino's tone()	2016-07-29 18:45:50 +01:00
João Brázio	8896f08074	Fixes a compilation error introduced by #4448	2016-07-29 18:33:42 +01:00
Scott Lahteine	ea5ac94804	Improved MANUAL_[XYZ]_HOME_POS ... No need for `MANUAL_HOME_POSITIONS`. Just set each one as-needed to override the automatic behavior.	2016-07-28 19:51:48 -07:00
Scott Lahteine	b40661cb18	Fix output of heater states	2016-07-28 17:40:01 -07:00
Scott Lahteine	9083e5420a	Merge pull request #4419 from AnHardt/sd2pinmap ... Switch Sd2CardLib to fastio	2016-07-28 17:38:46 -07:00
Scott Lahteine	6f59560526	Merge pull request #4448 from jbrazio/speaker-followup ... A little cleanup at speaker.h	2016-07-28 17:37:36 -07:00
Scott Lahteine	c94b6dd3e7	Revert to SanityCheck on every .cpp file	2016-07-28 17:17:50 -07:00
Scott Lahteine	256b03598d	Merge pull request #4450 from thinkyhead/rc_fix_delta_optimization ... Fix DELTA speed calculation	2016-07-28 16:50:04 -07:00
Scott Lahteine	753283e020	inverse_second => inverse_mm_s	2016-07-28 16:35:18 -07:00
Scott Lahteine	83e1d90ca3	Undo errant optimization of block->millimeters	2016-07-28 16:26:52 -07:00
João Brázio	909e98b1af	A little cleanup at speaker.h	2016-07-29 00:03:25 +01:00
Scott Lahteine	ae1c7bca1b	Merge pull request #4445 from thinkyhead/rc_fix_rdfgsc_mega3 ... Fix for R.D.F.G.S.C. with MEGATRONICS 3 board	2016-07-28 15:55:30 -07:00
Scott Lahteine	03fdb26cd2	Wrangle encoder bits, LCD_CLICKED	2016-07-28 14:44:37 -07:00
Scott Lahteine	155def24c6	BLEN_A, B, C are defined in ultralcd headers	2016-07-28 14:38:50 -07:00
Scott Lahteine	42dcc3bf50	Remove "the click" comments	2016-07-28 14:38:50 -07:00
Scott Lahteine	0eba65f96b	Fix for R.D.F.G.S.C. with MINITRONICS board	2016-07-28 14:38:50 -07:00
fabtopia	83d0d59303	Fix for R.D.F.G.S.C. with MEGATRONICS 3 board ... The support for reprapworld LCD boke the code for the REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER. See Full Grapics Display does not work any more after #4408 #4439	2016-07-28 13:12:19 -07:00
João Brázio	4f191a384b	Moves the font folder into the buildroot	2016-07-28 19:56:41 +01:00
Scott Lahteine	5367d56f87	Merge pull request #4434 from thinkyhead/rc_delta_safe_homing ... DELTA should ignore Z_SAFE_HOMING	2016-07-27 23:41:52 -07:00
Scott Lahteine	2525528fb2	DELTA should ignore Z_SAFE_HOMING	2016-07-27 23:25:56 -07:00
Scott Lahteine	ab4b2a66ff	Allow zero Z_RAISE_BETWEEN_PROBINGS	2016-07-27 05:00:58 -07:00
Scott Lahteine	8953e3e984	Allow Z_SAFE_HOMING without a probe	2016-07-27 04:33:56 -07:00
AnHardt	e4942d2163	Switch SD2cadrLib to fastio ... Replace all fastDigitalRead/Write() with READ/WRITE() Define SCK_PIN, MISO_PIN, MOSI_PIN in pins.h if not already defined in the pins_*.h files. Remove these conditional pin definitions from the pin-files. They are now always defined. Define separate sets of SPI-pins for AT90USB with and without Teensy support in fastio.h. Likely this was the main reason for all that confusion about the AT90USB-SPI pins.	2016-07-27 12:40:44 +02:00
Scott Lahteine	21e744c454	Allow zero raise for deploy/stow	2016-07-26 17:19:25 -07:00
Scott Lahteine	54084612fd	Merge pull request #4415 from petrzjunior/transl ... [LANGUAGE] Update Czech (Info screen strings)	2016-07-26 13:20:20 -07:00
Scott Lahteine	5597400cda	Merge pull request #4414 from thinkyhead/rc_split_conditionals ... Split up Conditionals.h into two files	2016-07-26 13:16:52 -07:00
Scott Lahteine	4be635ec6e	Remove MSG_PRINT_TIME from languages	2016-07-26 12:47:45 -07:00
Scott Lahteine	3be49881c0	Make SanityCheck.h a catch-all for obsolete configs	2016-07-26 12:41:40 -07:00
Scott Lahteine	fa647cca23	Do the sanity check just once per build	2016-07-26 12:37:14 -07:00
Scott Lahteine	24a1a16e5d	Move versioning to MarlinConfig.h	2016-07-26 12:37:14 -07:00
Scott Lahteine	7e70a0b05d	Move pins / Arduino includes to MarlinConfig.h	2016-07-26 12:37:14 -07:00
Scott Lahteine	d9f7ed9a3c	Move some macros from Marlin.h to macros.h	2016-07-26 12:37:13 -07:00
Scott Lahteine	277899c175	Move include _Bootscreen.h where needed	2016-07-26 12:37:13 -07:00
Scott Lahteine	83c4653c71	Include boards and macros ahead of configs	2016-07-26 12:19:50 -07:00
Scott Lahteine	5f4702ecb2	Make Conditionals.h a catch-all for old configs	2016-07-26 12:19:50 -07:00
Scott Lahteine	8a44928df3	Make Conditionals.h a catch-all for old configs	2016-07-26 12:19:50 -07:00
Petr Zahradník junior	3d9b878cf0	Czech update	2016-07-26 13:48:27 +02:00
Scott Lahteine	c6226bb0aa	Unify config in a single include without nested includes	2016-07-25 23:04:19 -07:00
Scott Lahteine	2d378fac1b	No need to include thermistortables.h in Configuration.h	2016-07-25 22:43:50 -07:00
Scott Lahteine	df27d01cd9	Arrange needed includes in Marlin.h	2016-07-25 20:53:36 -07:00
Scott Lahteine	93ea281061	Split up Conditionals.h into two files ... Rather than include twice, which is tricky but may confuse	2016-07-25 20:30:45 -07:00
Scott Lahteine	8684570f68	Merge pull request #4412 from thinkyhead/rc_followup_4402 ... Followup #4402 fixing 3-point leveling	2016-07-25 16:10:50 -07:00
Scott Lahteine	c55b7d0750	Merge pull request #4405 from thinkyhead/rc_theres_always_something ... Move HAS_DIGIPOTSS to Conditionals.h	2016-07-25 15:58:42 -07:00
Scott Lahteine	42eebcd518	Merge pull request #4409 from thinkyhead/rc_cleanup_comment ... Clean up Transfer Buffer Size comment	2016-07-25 15:58:34 -07:00
Scott Lahteine	5272147f7c	Followup #4402 fixing 3-point leveling	2016-07-25 15:56:34 -07:00
Scott Lahteine	fcc39e2b5f	Clean up Transfer Buffer Size comment	2016-07-25 12:54:55 -07:00
Scott Lahteine	0c0a63322b	Patches to prepare REPRAPWORLD_GRAPHICAL_LCD	2016-07-25 12:10:25 -07:00
brupje	a60a668f6b	Support for REPRAPWORLD_GRAPHICAL_LCD	2016-07-25 12:10:25 -07:00
Scott Lahteine	4f2ff46ab9	Move HAS_DIGIPOTSS to conditionals	2016-07-25 00:10:46 -07:00
Scott Lahteine	54f4f80077	Merge pull request #4404 from thinkyhead/rc_better_stepper_indirection ... Arrange stepper_indirection by axis	2016-07-24 19:26:39 -07:00
Scott Lahteine	169c21b477	Merge pull request #4402 from thinkyhead/rc_consistent_positioning ... Account for coordinate space offsets	2016-07-24 19:23:20 -07:00
Scott Lahteine	750a1e5116	Arrange stepper_indirection by axis	2016-07-24 19:00:51 -07:00
Scott Lahteine	7c27f34996	Merge pull request #4397 from thinkyhead/rc_tweak_eeprom ... Neaten up EEPROM read/write functions	2016-07-24 18:45:54 -07:00
Scott Lahteine	2595a40a61	Account for coordinate space more in G28 / G29 / M48	2016-07-24 18:34:05 -07:00
Scott Lahteine	060dc6d95a	Neaten up EEPROM read/write functions	2016-07-24 18:19:39 -07:00
Scott Lahteine	b7b7c90477	Merge pull request #4389 from thinkyhead/rc_optimize_planner ... Optimize planner with precalculation, etc.	2016-07-24 17:48:23 -07:00
Scott Lahteine	6900bb2286	Merge pull request #4395 from tnw513/italian_fix ... Update Italian translations. Remove trailing spaces.	2016-07-24 17:47:48 -07:00
Scott Lahteine	e4816293a8	serial_echopair_P for uint16_t	2016-07-24 17:46:37 -07:00
Scott Lahteine	d8e5af6834	Use RAW_POSITION for MBL in planner.set_position_mm	2016-07-24 17:20:36 -07:00
Scott Lahteine	b183442c61	Fix inactive_extruder_x_pos for coordinate space	2016-07-24 17:20:36 -07:00
Scott Lahteine	f75b0c2ee1	Make POSITION macros global	2016-07-24 17:20:36 -07:00
Scott Lahteine	101b60ef42	Tweak Dual X Carriage data spacing	2016-07-24 17:20:35 -07:00
Scott Lahteine	1fe60b723f	Merge pull request #4400 from thinkyhead/rc_sanity_check_temp_sensor ... Sanity check for too many temp sensors	2016-07-24 15:38:41 -07:00
Scott Lahteine	bedda3be61	Patch generic delta error caught by sanity check	2016-07-24 15:24:40 -07:00
Scott Lahteine	a5212bf277	Sanity check for too many temp sensors	2016-07-24 13:47:27 -07:00
Scott Lahteine	d8f2876753	Replace some float division with multiplication	2016-07-24 13:27:50 -07:00
Scott Lahteine	ddde785b37	Code formatting in planner.cpp	2016-07-24 13:27:50 -07:00
Scott Lahteine	f8b5749235	Replace division in planner with multiplication	2016-07-24 13:27:49 -07:00
Scott Lahteine	b921f6b69d	Optimize calculation of block->millimeters for DELTA	2016-07-24 13:27:49 -07:00
Scott Lahteine	db5df9500b	Move sync_plan_position closer to the top	2016-07-24 13:27:49 -07:00
Scott Lahteine	2839c56f5a	Merge pull request #4390 from jbrazio/duration_t ... Renamed timestamp_t to duration_t	2016-07-24 13:24:05 -07:00
Scott Lahteine	d6c50671d3	Sanitycheck: Z_SAFE_HOMING points are reachable	2016-07-24 10:54:47 -07:00
Scott Lahteine	a6203366b6	Sanitycheck: Z_SAFE_HOMING requires a probe	2016-07-24 10:54:25 -07:00
Scott Lahteine	bbe5b80492	Always define probe limits if there is a probe	2016-07-24 10:53:58 -07:00
Silvio Didonna	950397f2a0	Added missing translations. Removed trailing spaces for consistency (#4376)	2016-07-24 17:22:30 +02:00
João Brázio	50fb0f7cec	M31 serial output is now always in EN	2016-07-24 15:52:03 +01:00
João Brázio	62d96d72f3	Renamed timestamp_t to duration_t	2016-07-24 03:16:02 +01:00
Scott Lahteine	3e2b3353b0	Fix axis indices for COREYZ	2016-07-23 19:02:14 -07:00
Scott Lahteine	c287846f46	Merge pull request #4387 from thinkyhead/rc_anhardt_more_4370 ... Update Z in a unified way in run_z_probe	2016-07-23 16:47:10 -07:00
Scott Lahteine	22d0654fe6	Merge pull request #4382 from esenapaj/Update-Japanese-translation ... Update Japanese translation	2016-07-23 16:31:38 -07:00
Scott Lahteine	bb93b6822a	Use set_current_from_steppers_for_axis	2016-07-23 15:25:54 -07:00
AnHardt	96a162beda	Use implications from #4370 in run_z_probe() ... See also https://github.com/MarlinFirmware/Marlin/pull/4370#issuecomment-234713680	2016-07-23 13:09:28 -07:00
Scott Lahteine	4e67a85a5d	Macros to loop over axes	2016-07-23 13:09:28 -07:00
esenapaj	784be56e99	Follow-up the PR #4353 (General cleanup: enum) ... ・Update description of M111	2016-07-24 00:53:35 +09:00
esenapaj	3c11977558	Update Japanese translation ... ・Add translation ・Change translation ・Remove translation	2016-07-23 22:07:20 +09:00
Scott Lahteine	08459a003f	Undo the self-sabotage that is do_blocking_move_to_axis_pos	2016-07-23 00:59:11 -07:00
esenapaj	d32c4056ad	Fix for the PR #4379 (Additional logging of do_blocking_move_to) ... ・Remove unneeded PSTR()	2016-07-23 16:38:57 +09:00
Scott Lahteine	8099ee51a5	Merge pull request #4379 from thinkyhead/rc_blocking_move_logging ... Additional logging of do_blocking_move_to	2016-07-23 00:10:55 -07:00
Scott Lahteine	8633b644cf	Merge pull request #4378 from thinkyhead/rc_debug_leveling_docs ... Document DEBUG_LEVELING_FEATURE	2016-07-22 23:57:01 -07:00
Scott Lahteine	ad16d5019e	Additional logging of do_blocking_move_to	2016-07-22 23:53:08 -07:00
Scott Lahteine	bb9da6ebdd	Document DEBUG_LEVELING_FEATURE	2016-07-22 23:37:41 -07:00
Scott Lahteine	652fd8a826	Merge pull request #4362 from thinkyhead/rc_duplication_mode ... DUAL_NOZZLE_DUPLICATION_MODE	2016-07-22 21:17:59 -07:00
Scott Lahteine	1766b990b8	Merge pull request #4376 from jbrazio/timestamp_t-short ... Adds short format to timestamp_t	2016-07-22 21:17:17 -07:00
Scott Lahteine	6da3729531	Merge pull request #4370 from thinkyhead/rc_delta_fwd_kinematics ... Delta Forward Kinematics (and LOGICAL_POSITION)	2016-07-22 21:16:00 -07:00
João Brázio	9e5dbf67e8	Update the stats menu to include longest job and extruded filament	2016-07-23 03:05:45 +01:00
João Brázio	86d9311495	Rework LCD implementation to use timestamp_t	2016-07-23 03:05:36 +01:00
Scott Lahteine	b3eb0c8569	Add LOGICAL_POSITION macro, apply to kinematics	2016-07-22 18:38:13 -07:00
Scott Lahteine	35a610abf9	const arg to inverse_kinematics	2016-07-22 17:42:48 -07:00
João Brázio	b4aad85c9a	Rework stats menu to use timestamp_t	2016-07-23 01:42:21 +01:00
João Brázio	ecd48027fa	Adds short timestamp format to timestamp_t	2016-07-23 01:41:25 +01:00
Scott Lahteine	b6afa028f4	Don't call adjust_delta on SCARA	2016-07-22 16:36:34 -07:00
Scott Lahteine	d5e2d523c7	Generalize kinematics function names	2016-07-22 16:36:34 -07:00
Scott Lahteine	9c4ad7d7ef	Clean up delta declarations in Marlin_main.cpp	2016-07-22 16:36:33 -07:00
Scott Lahteine	4b1725628b	Move kinematic functions to "private" scope	2016-07-22 16:36:33 -07:00
Scott Lahteine	cde068ea42	Use set_current_from_steppers in quickstop_stepper	2016-07-22 16:36:33 -07:00
Scott Lahteine	9f30cc84ce	Use set_current_from_steppers for other kinematics	2016-07-22 16:36:33 -07:00
AnHardt	5db9b940ee	Use forwardKinematics in DELTA run_z_probe()	2016-07-22 16:36:33 -07:00
Scott Lahteine	b5a9647fec	Use ENABLED in stepper_indirection.h	2016-07-22 16:26:06 -07:00
Scott Lahteine	cbc7f22ad9	Implement DUAL_NOZZLE_DUPLICATION_MODE	2016-07-22 16:23:58 -07:00
Scott Lahteine	91777dd76c	Add DUAL_NOZZLE_DUPLICATION_MODE option	2016-07-22 16:22:56 -07:00
Scott Lahteine	260bbb3109	Fix a couple of simple typos	2016-07-22 16:22:56 -07:00
Scott Lahteine	179e091473	Merge pull request #4374 from thinkyhead/rc_jbrazio_timestamp_t ... Implements timestamp_t structure	2016-07-22 16:08:10 -07:00
AnHardt	499e404fbf	forwardKinematics for Delta printers	2016-07-22 16:01:51 -07:00
João Brázio	23043a1e05	Rework some code to use timestamp_t struct (saves 72 bytes)	2016-07-22 15:53:31 -07:00
João Brázio	9388dcfa49	Implements timestamp_t structure	2016-07-22 15:53:31 -07:00
Scott Lahteine	0b2c608d2f	Merge pull request #4372 from jbrazio/gcc-bark ... Fix minor gcc warning	2016-07-22 15:18:53 -07:00
Scott Lahteine	311c7dadb6	Cleanup do_blocking_move_to for DELTA	2016-07-22 14:18:45 -07:00
Scott Lahteine	b78590e63d	Patch and cleanup run_z_probe	2016-07-22 14:18:45 -07:00
João Brázio	2f7716987d	Fix minor gcc warning	2016-07-22 16:08:56 +01:00
João Brázio	efd3aabda8	Adds missing documentation to the point_t structure	2016-07-22 15:19:20 +01:00
Scott Lahteine	39caef4279	Merge pull request #4361 from AnHardt/imp-dbmt-for-delta ... DELTA do_blocking_move_to() more like the Chartesian one	2016-07-21 20:05:04 -07:00
Scott Lahteine	7d869ad98b	Merge pull request #4365 from thinkyhead/rc_shrink_planner_accel ... Adjustments to planner acceleration limit	2016-07-21 18:18:15 -07:00
AnHardt	376a57232e	DELTA do_blocking_move_to() more like the Chartesian one	2016-07-22 03:12:46 +02:00
Scott Lahteine	824c6859e2	Merge pull request #4369 from thinkyhead/rc_no_static_moves ... inline to fix warnings, smaller build size (sometimes)	2016-07-21 14:46:09 -07:00
Scott Lahteine	976c31235d	inline to fix warnings, smaller build size (sometimes)	2016-07-21 13:49:37 -07:00
AnHardt	6ef26a85d8	Back to the differences method in run_z_probe()	2016-07-21 18:16:38 +02:00
Scott Lahteine	4226f56f53	Revert the planner acceleration logic somewhat	2016-07-20 19:19:47 -07:00
Scott Lahteine	16e5348659	Merge pull request #4360 from thinkyhead/rc_toolchange_for_G28 ... Always switch to tool 0 for G28	2016-07-20 19:07:35 -07:00
Scott Lahteine	209f5c03d0	Fewer temporary vars in planner accel limit	2016-07-20 18:29:29 -07:00
Scott Lahteine	62ecd107ba	Patch ultralcd_impl header conditional names	2016-07-20 09:36:55 -07:00
Scott Lahteine	d2e9a9c188	Always switch to tool 0 for G28	2016-07-20 09:36:55 -07:00
Scott Lahteine	194d9521c3	Merge pull request #4356 from thinkyhead/rc_simpler_run_z_probe ... Unify run_z_probe	2016-07-19 19:02:39 -07:00
Scott Lahteine	4a6ed5e221	Use HOMING_FEEDRATE_Z for Z_PROBE_SPEED_FAST	2016-07-19 18:42:48 -07:00
AnHardt	09a3cc33e6	Unify run_z_probe ... Unify run_z_probe Add double touch for DELTAs. Introduce Z_PROBE_SPEED_FAST and Z_PROBE_SPEED_SLOW defaulting to homing_feedrate_mm_m[Z_AXIS] and homing_feedrate_mm_m[Z_AXIS]/2	2016-07-19 18:42:48 -07:00
Scott Lahteine	6137a1d934	Merge pull request #4359 from thinkyhead/rc_wrangle_movement_etc ... Use ENABLED(MAPPER_NON)	2016-07-19 18:22:55 -07:00
Scott Lahteine	0432613ad7	use enabled macro for mapper setting	2016-07-19 18:08:56 -07:00
Scott Lahteine	e44b37cdc2	motion section marker below homing speeds	2016-07-19 17:31:58 -07:00
Scott Lahteine	204fd6ec44	Set homing feedrates individually	2016-07-19 17:31:58 -07:00
Scott Lahteine	2bad02e60d	Reprapworld Keypad: F1 opens the Move Axis menu	2016-07-19 16:40:39 -07:00
Scott Lahteine	eaa6f568ee	Prevent re-entrant call of Reprapworld Keypad handler	2016-07-19 16:40:39 -07:00
Scott Lahteine	6abf916575	Reprapworld Keypad move step is 1mm	2016-07-19 16:40:39 -07:00
Scott Lahteine	06ac1f3bcf	Reduce Reprapworld Keypad move code size	2016-07-19 16:40:39 -07:00
Scott Lahteine	5d5affdfca	Merge pull request #4355 from thinkyhead/rc_rename_ultralcd_files ... Rename ultralcd implementation files for consistency	2016-07-19 16:14:27 -07:00
Scott Lahteine	bb225dedc6	Merge pull request #4354 from thinkyhead/rc_jbrazio_rework_g12 ... NOZZLE_CLEAN_FEATURE with no dependency on HAS_BED_PROBE	2016-07-19 15:26:59 -07:00
Scott Lahteine	8a2efd1155	Rename ultralcd implementation files for consistency	2016-07-19 15:26:14 -07:00
João Brázio	b869fbc05e	Update all config files with the new G12 options	2016-07-19 15:07:03 -07:00
João Brázio	47fef80848	Nozzle::clean() no longer requires HAS_BED_PROBE	2016-07-19 15:07:02 -07:00
Scott Lahteine	f1f1bac0e1	Merge pull request #4341 from esenapaj/Update-Japanese-translation ... Update Japanese translation	2016-07-19 15:04:22 -07:00
Scott Lahteine	6c899bb520	Merge pull request #4349 from jbrazio/gcc-bark-bark ... Removes some minor GCC warnings	2016-07-19 13:42:33 -07:00
Scott Lahteine	ef0a22871e	Merge pull request #4350 from jbrazio/followup-a875861 ... Adds utility.h	2016-07-19 13:40:52 -07:00
Scott Lahteine	9eba58a031	Merge pull request #4351 from jbrazio/u8glib-converter ... Updates u8glib's bmp2hex converter	2016-07-19 13:39:33 -07:00
Scott Lahteine	c502018eab	Merge pull request #4353 from jbrazio/global-enum-file ... General cleanup: enum	2016-07-19 13:37:56 -07:00
Scott Lahteine	0f9953b031	Merge pull request #4342 from AnHardt/rep-cons-g28 ... Introduce line_to_axis_pos() for use in homeaxis()	2016-07-19 12:56:58 -07:00
AnHardt	11c075c6b2	Introduce line_to_axis_pos(axis_codes axis, float where, float feed_rate = 0.0) ... and use it in `homeaxis()` instead of `do_blocking_move_to_axis_pos()`. `do_blocking_move_to_axis_pos` was wrong because it performed subdivided, delta-corrected moves for x- and y-axis. The first common move for delta homing is like quick_home but for 3 towers. Fix two warnings.	2016-07-19 17:24:44 +02:00
João Brázio	3ebad4e020	Moves all global enums to a central file	2016-07-19 14:31:09 +01:00
João Brázio	238fefcb00	Updates Stopwatch class to use internal state enum	2016-07-19 14:30:44 +01:00
João Brázio	30ac0782a9	Comment section style correction	2016-07-19 03:27:42 +01:00
João Brázio	8ecee431c4	Updates u8glib's bmp2hex converter	2016-07-19 03:16:30 +01:00
João Brázio	79e7721b76	Removes some minor GCC warnings	2016-07-19 03:03:11 +01:00
João Brázio	f4d63796b2	Adds utility.h	2016-07-19 02:55:23 +01:00
esenapaj	361307831e	Follow-up the PR #4335 (Debug char, fix compile errors for lcd pins) ... ・Solve a flickering when SD card is inserted or removed at using a ASCII LCD + language_kana.h	2016-07-18 20:09:24 +09:00
esenapaj	ff48bbb86a	Update Japanese translation ... ・Add new translation	2016-07-18 17:01:56 +09:00
Scott Lahteine	46117593b9	Merge pull request #4185 from esenapaj/Update-Japanese-translation ... Update Japanese translation (work in progress)	2016-07-17 18:36:34 -07:00
Scott Lahteine	3422103863	Merge pull request #4310 from thinkyhead/rc_mbl_position_shift ... Fix position shift with MBL	2016-07-17 18:31:25 -07:00
Scott Lahteine	92757bd7b3	Merge pull request #4339 from esenapaj/Follow-up-the-PR-#4163 ... Follow-up the PR #4163 (Mixing and Switching Extruders)	2016-07-17 18:15:23 -07:00
Scott Lahteine	493d30cd97	Drop intermediate nx, ny, and set destination directly	2016-07-17 17:59:52 -07:00
Scott Lahteine	07a735ad22	We always use destination so modify mesh_buffer_line	2016-07-17 17:57:33 -07:00
Scott Lahteine	04a5b7b257	A macro to normalize positions	2016-07-17 17:57:32 -07:00
esenapaj	5c8e87a866	Follow-up the PR #4163 (Mixing and Switching Extruders) ... ・Update forgotten K8400 files	2016-07-18 09:48:13 +09:00
Scott Lahteine	86eb5251c5	Fix some debug messages	2016-07-17 17:10:02 -07:00
Scott Lahteine	1e57a6af73	Use blocking_move, current_position in G28 homing	2016-07-17 16:56:13 -07:00
Scott Lahteine	f6a3a1da09	nz and ne are always set, so drop them down	2016-07-17 14:12:39 -07:00
Scott Lahteine	d0009e013b	Rename cell index vars	2016-07-17 14:12:39 -07:00
Scott Lahteine	697373b071	Reduce code size of mesh_buffer_line	2016-07-17 14:11:25 -07:00
Scott Lahteine	103d312f6d	MBL can actually do up to 9 x 9	2016-07-17 14:11:25 -07:00
Scott Lahteine	f4a69281fc	Only call mesh_buffer_line when MBL is active	2016-07-17 14:11:25 -07:00
Scott Lahteine	799a31cd30	Include the position_shift when splitting mesh lines	2016-07-17 14:08:20 -07:00
Scott Lahteine	f242aea032	Merge pull request #4319 from thinkyhead/rc_feedrates_to_mess_with_you ... Wrangle feed rate variables	2016-07-17 14:07:52 -07:00
Scott Lahteine	0342661b3f	Merge pull request #4335 from thinkyhead/rc_status_pad_jp ... Debug char, fix compile errors for lcd pins	2016-07-17 14:07:08 -07:00
Scott Lahteine	81e01152bb	Merge pull request #4336 from thinkyhead/rc_bltouch_sensor ... BLTouch probe sensor	2016-07-17 14:06:32 -07:00
Scott Lahteine	1583177ef4	BLTOUCH probe config option	2016-07-17 13:55:38 -07:00
Scott Lahteine	176b9627c7	Some cleanup ahead of BLTOUCH support	2016-07-17 13:55:38 -07:00
Scott Lahteine	39706f3e57	Endstop invert flags as macros instead of const bool	2016-07-17 13:51:02 -07:00
Scott Lahteine	7242d44810	Endstops vars already initialized	2016-07-17 13:38:48 -07:00
Scott Lahteine	5ed1e7a464	codenum => dwell_ms	2016-07-17 13:35:21 -07:00
Scott Lahteine	69d6016941	Revert default state of endstops in M502	2016-07-17 13:35:21 -07:00
Scott Lahteine	0fcd3706dd	Replace ENDSTOPS_ONLY_FOR_HOMING with ENDSTOPS_ALWAYS_ON_DEFAULT	2016-07-17 13:35:21 -07:00
Scott Lahteine	671634bf11	Fix spacing after section header	2016-07-17 13:35:21 -07:00
Scott Lahteine	f38553b482	fix a debug message	2016-07-17 13:29:42 -07:00
Scott Lahteine	3d78b8f929	Use HYPOT macro instead of hypot function	2016-07-17 13:29:42 -07:00
Scott Lahteine	9f9fe043ba	Apply sq macro throughout	2016-07-17 13:29:41 -07:00
Scott Lahteine	93ba5bddd7	Append units to feedrate variables	2016-07-17 13:29:41 -07:00
Scott Lahteine	5e3d3918b6	Patch compile error for RAMPS LCD pins	2016-07-17 12:27:37 -07:00
Scott Lahteine	94955a8bf7	pad string in lcd_finishstatus	2016-07-17 12:27:37 -07:00
Scott Lahteine	21ee0612e3	Debug char	2016-07-17 12:27:36 -07:00
Scott Lahteine	8f24e0a556	Debugging of MBL in G28	2016-07-17 11:08:30 -07:00
Scott Lahteine	05da02f0a2	Implement MIXING_EXTRUDER and SWITCHING_EXTRUDER	2016-07-17 10:53:10 -07:00
Scott Lahteine	22b4cff423	New extruder type configuration options	2016-07-17 00:13:56 -07:00
esenapaj	601015b73e	Update Japanese translation	2016-07-17 16:04:12 +09:00
Scott Lahteine	9766e24504	Merge pull request #4277 from thinkyhead/rc_mks_13_viki2 ... Support for VIKI2 with MKS 1.3 / 1.4	2016-07-16 23:49:33 -07:00
Scott Lahteine	02285662f5	Merge pull request #4298 from jbrazio/feature/filament-counter ... Adds filamentUsed and longestPrint stats to PrintCounter	2016-07-16 23:48:46 -07:00
Scott Lahteine	bf16ae5a70	Merge pull request #4299 from jbrazio/feature/g27-park-nozzle ... Implements park nozzle feature	2016-07-16 23:47:12 -07:00
Scott Lahteine	aaa0d298b9	Merge pull request #4326 from thinkyhead/rc_no_static_items_fix ... Suppress compiler warnings in ultralcd.cpp	2016-07-16 23:38:08 -07:00
Scott Lahteine	cc3ef73583	Merge pull request #4327 from thinkyhead/rc_petrzjr_long_print ... LCD Longer print	2016-07-16 23:37:34 -07:00
Scott Lahteine	77c8fb627f	Merge pull request #4329 from thinkyhead/rc_italian_fix ... Added missing Italian translations	2016-07-16 23:37:15 -07:00
Scott Lahteine	b14888501b	Merge pull request #4301 from Ingramz/RCBugFix ... Add Cartesio CN Controls V11	2016-07-16 22:35:07 -07:00
Silvio Didonna	32e0d71729	Added missing translations	2016-07-16 22:26:46 -07:00
Scott Lahteine	0f3232065e	Merge pull request #4305 from jbrazio/feature/splash-improvement ... Custom boot screen feature improvement	2016-07-16 21:59:39 -07:00
Petr Zahradník junior	2d7fe9dc78	LCD Longer print	2016-07-16 18:21:06 -07:00
Scott Lahteine	eee903bd4b	Format some DAC lines	2016-07-16 17:59:13 -07:00
Scott Lahteine	d53dcaa796	Suppress some compiler warnings	2016-07-16 17:59:01 -07:00
João Brázio	fa4274cf4c	Improves the custom bootscreen logo feature	2016-07-17 01:31:44 +01:00
João Brázio	1f3283e3a5	Adds custom boot logos for bq Hephestos 2 and Cartesio	2016-07-17 01:31:36 +01:00
João Brázio	dfa1c45075	Adds a notice to vendors about the SHOW_CUSTOM_BOOTSCREEN directive	2016-07-17 01:15:17 +01:00
Scott Lahteine	ed468e848f	Merge pull request #4321 from esenapaj/Follow-up-the-PR-#4287 ... Follow-up and fix the PR #4287 (Allow stopwatch and printcounter to go over 18:12:15)	2016-07-16 17:14:21 -07:00
João Brázio	a8758619ec	The safe_delay() is now globaly accessible	2016-07-16 12:28:06 +01:00
João Brázio	9a00108cb6	Adds the WEBSITE_URL as the boot screen line 2	2016-07-16 12:24:37 +01:00
João Brázio	f5234b0695	Adds a customizable screen timeout for the default boot screen	2016-07-16 12:24:36 +01:00
João Brázio	2f26bc2153	Adds filamentUsed and longestPrint stats to PrintCounter	2016-07-16 12:12:27 +01:00
João Brázio	336481ea81	Added G27 configuration options to all configs	2016-07-16 12:07:59 +01:00
João Brázio	c711701626	Implements a nozzle parking command (G27)	2016-07-16 12:07:59 +01:00
João Brázio	5f368d1bc3	Followup for #4320	2016-07-16 11:57:35 +01:00
João Brázio	d7c51bc4b9	Merge pull request #4320 from jbrazio/followup/4307 ... Moves do_blocking_move_to_xy() out of the HAS_BED_PROBE define	2016-07-16 11:48:00 +01:00
esenapaj	af9b1d79b1	Follow-up and fix the PR #4287 (Allow stopwatch and printcounter to go over 18:12:15) ... ・Remove MSG_END_HOUR and MSG_END_MINUTE from all the language files ・Change from MSG_INFO_TOTAL_PRINTS to MSG_INFO_PRINT_COUNT in German file	2016-07-16 18:39:22 +09:00
Scott Lahteine	e563634a25	Merge pull request #4314 from AnHardt/use-d_b_m_t-in-g28 ... Use do_blicking_move_to*() in G28	2016-07-15 20:22:02 -07:00
Scott Lahteine	59ae1811c2	Merge pull request #4303 from AnHardt/delta-g28 ... DELTA: Move out of the clip-zone after G28	2016-07-15 20:20:22 -07:00
João Brázio	fdea8b6e6a	Moves do_blocking_move_to_xy() out of the HAS_BED_PROBE define	2016-07-16 03:59:49 +01:00
AnHardt	d2a49c016d	DELTA: Move out of the clip-zone after G28 ... Move down to a safe height after G28 for DELTAs.	2016-07-15 15:22:44 +02:00
AnHardt	46994fd17d	Use do_blicking_move_to*() in G28	2016-07-15 15:02:15 +02:00
João Brázio	ffbb31b235	Fixes an PSTR overflow with print_xyz()	2016-07-15 11:25:34 +01:00
Indrek Ardel	ecb23c1b65	Add Cartesio CN Controls V11 board	2016-07-15 12:55:47 +03:00
Indrek Ardel	c8f2dd7cd5	Fix CN Controls 12 styling	2016-07-15 09:54:09 +03:00
Scott Lahteine	cec7110409	Merge pull request #4308 from thinkyhead/rc_debug_gcode_t ... Added logging related to gcode_T	2016-07-14 19:46:33 -07:00
Scott Lahteine	6446d3939a	Merge pull request #4309 from thinkyhead/rc_static_item_fix_77 ... Fix skipping of static items	2016-07-14 19:28:49 -07:00
Scott Lahteine	95ab2fd3ae	Fix skipping of static items	2016-07-14 19:16:16 -07:00
Scott Lahteine	166f19251e	Add more debugging for leveling ... - Especially in `gcode_T` - In `update_software_endstops` - Some tweaks to observe	2016-07-14 19:04:13 -07:00
Scott Lahteine	7ac0b91a45	Collapsible long comment in gcode_T	2016-07-14 18:28:41 -07:00
João Brázio	e71a631f8f	do_blocking_move_*() no longer depend on HAS_BED_PROBE	2016-07-15 01:54:14 +01:00
Scott Lahteine	8bf6861af8	Merge pull request #4054 from jbrazio/feature/g12-clean-tool ... Implements clean nozzle feature (Lulzbot's REWIPE)	2016-07-14 14:38:38 -07:00
Scott Lahteine	c5e51f6b96	finished => completed	2016-07-14 11:46:35 -07:00
Scott Lahteine	1618870c84	card.printingHasFinished does print_job_timer.stop	2016-07-14 11:39:58 -07:00
Scott Lahteine	34da77dad3	Simply run M31 at the end of an SD print	2016-07-14 11:39:58 -07:00
Scott Lahteine	23d2bc5ab0	Patch Greek for new strings	2016-07-14 11:39:58 -07:00
Scott Lahteine	a8d71f0ac6	Support longer print times in M31	2016-07-14 11:39:58 -07:00
Scott Lahteine	e481b79af1	Allow stopwatch and printcounter to go over 18 hours	2016-07-14 11:39:57 -07:00
João Brázio	68c343a09a	Added G12 configuration options to all configs	2016-07-14 00:38:42 +01:00
João Brázio	4937f9ada4	Minor G12 tweaks and point_t struct extension	2016-07-14 00:07:36 +01:00
Scott Lahteine	6080924589	Merge pull request #4296 from jbrazio/feature/bqh2-update ... Update the bq Hephestos 2 configuration	2016-07-13 13:18:09 -07:00
Scott Lahteine	ed89c71e53	Merge pull request #4291 from esenapaj/Follow-up-the-PR-#4278 ... Follow-up the PR #4278 (Fixups for PID_ADD_EXTRUSION_RATE and HOTENDS==1)	2016-07-13 13:17:03 -07:00
João Brázio	021544f572	Improves G12 zig-zag pattern	2016-07-13 21:14:56 +01:00
João Brázio	b05a75655a	Implements a nozzle cleaning pattern generator (G12)	2016-07-13 21:14:19 +01:00
João Brázio	005af84140	Update the bq Hephestos 2 configuration	2016-07-13 21:06:31 +01:00
esenapaj	8f03f0be9b	Follow-up the PR #4252 (Replace PLA/ABS preheating with generic)	2016-07-13 22:42:16 +09:00
esenapaj	c2c8ab4698	Follow-up the PR #4278 (Fixups for PID_ADD_EXTRUSION_RATE and HOTENDS==1)	2016-07-13 22:24:31 +09:00
Scott Lahteine	4f77adddbe	Merge pull request #4286 from thinkyhead/rc_debug_clean ... Prefix and suffix in debug output	2016-07-12 20:49:15 -07:00
Scott Lahteine	e5c7af5ddc	Merge pull request #4222 from thinkyhead/rc_allow_cold_extrude ... M302: Add "P" parameter, status output	2016-07-12 20:40:14 -07:00
Scott Lahteine	2224032568	Merge pull request #4285 from thinkyhead/rc_manual_move_fast_fine ... No delay for the smallest LCD moves	2016-07-12 20:16:38 -07:00
Scott Lahteine	cdd77d23bb	Neaten up temperature member data	2016-07-12 20:04:15 -07:00
Scott Lahteine	d4c68279c8	Add "P" parameter to M302	2016-07-12 20:04:15 -07:00
Scott Lahteine	a5bae3c7d5	Merge pull request #4229 from blubbfish/patch-1 ... Update language_de.h for German translation	2016-07-12 20:01:46 -07:00
Scott Lahteine	a8b6b6a128	Merge pull request #4252 from thinkyhead/rc_rename_hpb ... Replace PLA/ABS preheating with generic	2016-07-12 20:00:33 -07:00
Scott Lahteine	1e14df876d	Use varname as prefix in DEBUG_POS, string as suffix	2016-07-12 19:58:09 -07:00
Scott Lahteine	9e8b3e5ee6	Homing direction is irrelevant in probe raise!	2016-07-12 18:09:02 -07:00
Scott Lahteine	ecd5e810ac	No delay for the smallest LCD moves	2016-07-12 18:09:01 -07:00
Scott Lahteine	2b9515d60f	Merge pull request #4281 from AnHardt/lang-system ... Don't use UTF-strlen() if the text is not UTF	2016-07-12 17:21:28 -07:00
Scott Lahteine	973a669aa3	Merge pull request #4264 from thinkyhead/rc_ultralcd_encoder_pos ... Remove extraneous conditions for encoder position	2016-07-12 16:54:13 -07:00
Scott Lahteine	e9f62d8fdb	Remove extraneous conditions for encoder position	2016-07-12 16:41:00 -07:00
Scott Lahteine	7c81398f95	Merge pull request #4279 from esenapaj/Follow-up-the-PR-#4271 ... Follow-up the PR #4271 (X_DUAL_STEPPER_DRIVERS)	2016-07-12 16:39:37 -07:00
Scott Lahteine	0554b65d22	Merge pull request #4284 from thinkyhead/rc_serial_ln_macros ... Sled-probe sanity fix, conditionals for remaining types of leveling	2016-07-12 16:36:33 -07:00
Scott Lahteine	655c3fd55f	Move delta ABL sanity checks up	2016-07-12 16:10:16 -07:00
Scott Lahteine	db0882d068	AUTO_BED_LEVELING_3POINT and DELTA_BED_LEVELING_GRID	2016-07-12 16:10:11 -07:00
Scott Lahteine	e974ac63ef	Init matrix in planner.init	2016-07-12 15:55:27 -07:00
Scott Lahteine	47d55513ec	Merge pull request #4280 from AnHardt/msg-file-upload ... Finalalize MSG_SD_WRITE_TO_FILE message with a \n	2016-07-12 13:02:52 -07:00
AnHardt	b273736962	Make MAPPER_NON the fall back mapper ... Make MAPPER_NON the fall back mapper - if no other is defined. One list less to maintain.	2016-07-12 19:59:14 +02:00
AnHardt	54d35230df	Don't use UTF-strlen() if the text is not UTF	2016-07-12 19:59:03 +02:00
Scott Lahteine	a1de96d152	Merge pull request #4278 from thinkyhead/rc_more_hotends_1 ... Fixups for PID_ADD_EXTRUSION_RATE and HOTENDS==1	2016-07-12 10:36:13 -07:00
AnHardt	87957c7b44	Finalalize MSG_SD_WRITE_TO_FILE message with a \n ... Finalalize MSG_SD_WRITE_TO_FILE message with a \n else RH hangs.	2016-07-12 13:13:04 +02:00
esenapaj	9b5cbf2423	Follow-up the PR #4271 (X_DUAL_STEPPER_DRIVERS) ... ・Update a forgotten Configuration_adv.h of K8400	2016-07-12 17:50:49 +09:00
Scott Lahteine	809da999dc	Apply HOTEND_INDEX in preheat methods	2016-07-11 22:27:25 -07:00
Scott Lahteine	3d78b690e5	Single PID dataset with HOTENDS == 1	2016-07-11 22:27:24 -07:00
Scott Lahteine	bf9967c65d	Apply HOTEND_INDEX in MILLISECONDS_PREHEAT_TIME	2016-07-11 22:27:24 -07:00
Scott Lahteine	11dcbae7a2	Only a single E axis. Can tool-change reseed position[E_AXIS]?	2016-07-11 22:27:24 -07:00
Scott Lahteine	4865447830	Merge pull request #4276 from esenapaj/Suppress-warnings ... Suppress warnings	2016-07-11 19:08:59 -07:00
Scott Lahteine	815df28b0b	Merge pull request #4274 from esenapaj/Follow-up-the-PR-#4024 ... Follow-up the PR #4024 (Greek Language by @psavva)	2016-07-11 19:04:44 -07:00
Scott Lahteine	44f739a5eb	Merge pull request #4273 from esenapaj/Fix-for-the-PR-#4256 ... Fix for the PR #4256 (Additional tweaks for HOTENDS == 1)	2016-07-11 19:02:45 -07:00
Scott Lahteine	02f711fe00	Merge pull request #4275 from AnHardt/dont-deploy ... Don't deploy/stow the probe if z-min-endstop is used for homing	2016-07-11 18:46:23 -07:00
Scott Lahteine	6a45aad893	Merge pull request #4272 from AnHardt/m100-rep ... Repair M100	2016-07-11 18:45:13 -07:00
Scott Lahteine	243ad4312a	Merge pull request #4271 from thinkyhead/rc_X_DUAL_STEPPER_DRIVERS ... X_DUAL_STEPPER_DRIVERS	2016-07-11 18:38:45 -07:00
Scott Lahteine	6e68dd292b	Merge pull request #4243 from thinkyhead/rc_fix_static_scrolling ... Improve STATIC_ITEM implementation	2016-07-11 18:25:00 -07:00
Scott Lahteine	d17b161832	Don't draw current screen if simply changing screens	2016-07-11 18:14:04 -07:00
Scott Lahteine	096f9981d1	Scroll to the top when changing screens	2016-07-11 18:14:04 -07:00
Scott Lahteine	7ae84d768e	Tweak conditionals for REPRAPWORLD_KEYPAD	2016-07-11 18:14:04 -07:00
Scott Lahteine	155af6b861	Rename vars, add comments for menu macros	2016-07-11 18:14:04 -07:00
Scott Lahteine	31f2cf5f6f	Make encoderLine signed for proper compares	2016-07-11 18:14:03 -07:00
Scott Lahteine	d9f75f62c0	START_ROW => START_COL	2016-07-11 18:14:03 -07:00
Scott Lahteine	d2099fef0d	Left-justify thermistor info	2016-07-11 18:14:03 -07:00
Scott Lahteine	85aeb02aa6	Invert headings on Graphical LCD	2016-07-11 18:14:03 -07:00
Scott Lahteine	3a67fb77b0	Concatenate LCD static strings	2016-07-11 18:14:02 -07:00
Scott Lahteine	13dc619f43	Scroll static screens more simply	2016-07-11 18:14:02 -07:00
Scott Lahteine	5051723c2e	Redraw after cursor correction in STATIC_ITEM	2016-07-11 18:14:02 -07:00
esenapaj	58177a1602	Suppress warnings	2016-07-12 08:22:24 +09:00
Scott Lahteine	10ebf28ee3	Allow override of ENCODER_FEEDRATE_DEADZONE, lower default for Viki	2016-07-11 15:43:08 -07:00
Scott Lahteine	9b1ba1012a	Support for VIKI2 with MKS Gen 1.3 / 1.4	2016-07-11 15:43:08 -07:00
Scott Lahteine	55dc8051d8	Cleanup of RAMPS LCD pins	2016-07-11 15:38:55 -07:00
AnHardt	7bcab26f2a	Don't deploy/stow the probe if z-min-endstop is used for homing ... Don't deploy/stow the probe if z-min-endstop is used for homing. Don't apply `zprobe_zoffset` if probe was not used.	2016-07-11 22:01:44 +02:00
esenapaj	84ded1f659	Follow-up the PR #4024 (Greek Language by @psavva) ... ・Update forgotten Configuration.h of K8400	2016-07-12 04:19:09 +09:00
esenapaj	6af525e252	Fix for the PR #4256 (Additional tweaks for HOTENDS == 1)	2016-07-12 03:51:29 +09:00
AnHardt	23e0134596	Repair M100 ... M100 D was running too long - caused watchdog resets. M100 I showed more free memory than a Arduino Mega has RAM.	2016-07-11 20:44:30 +02:00
Scott Lahteine	4b4a582c4f	X_DUAL_STEPPER_DRIVERS implementation	2016-07-11 10:22:19 -07:00
Scott Lahteine	91bd6eade7	X_DUAL_STEPPER_DRIVERS configuration option	2016-07-11 10:22:19 -07:00
Scott Lahteine	6121c9018a	Merge pull request #4265 from thinkyhead/rc_buzzer_patchup ... Two strategies to address a stuck buzzer	2016-07-10 19:46:15 -07:00
Scott Lahteine	4a100c6832	Merge pull request #4250 from AnHardt/wait-for-cooling-slope ... Adjust wait_for_cooling slope	2016-07-10 19:45:23 -07:00
Scott Lahteine	ed018c98d5	Merge pull request #4024 from thinkyhead/rc_greek_language ... Greek Language by @psavva	2016-07-10 19:42:09 -07:00
Scott Lahteine	d1dffc7ad1	timestamp => endtime	2016-07-10 19:36:46 -07:00
Scott Lahteine	71674059c3	Two strategies to address a stuck buzzer	2016-07-10 19:25:23 -07:00
Scott Lahteine	928ff6487a	Greek language pack from @psavva	2016-07-10 18:59:04 -07:00
AnHardt	e92e58df1f	Adjust wait_for_cooling slope ... Adjust wait_for_cooling slope and drop mintemp for cooling. See https://github.com/MarlinFirmware/Marlin/pull/4169#issuecomment-231544532	2016-07-11 03:36:23 +02:00
Scott Lahteine	167f4aa0cc	Merge pull request #4259 from clexpert/patch-3 ... Update language_cz.h	2016-07-10 18:26:23 -07:00
Scott Lahteine	8dda05e92a	Merge pull request #4258 from clexpert/patch-2 ... Total print time for LCD correction (hours:minutes format)	2016-07-10 18:25:18 -07:00
Scott Lahteine	182c8d7f8f	Dyze High Temp Thermistor Support	2016-07-10 17:59:05 -07:00
Scott Lahteine	5b0e46c986	Merge pull request #4256 from thinkyhead/rc_fix_singlenozzle_temp ... Additional tweaks for HOTENDS == 1	2016-07-10 17:57:00 -07:00
Scott Lahteine	ee0983ab57	Further reduction when HOTENDS == 1	2016-07-10 16:54:30 -07:00
Scott Lahteine	3e1bbd5e27	Indentation in gcode_M100	2016-07-10 16:33:51 -07:00
Scott Lahteine	b72238f406	Invariant get_pid_output with HOTENDS < 2	2016-07-10 16:33:51 -07:00
Petr Zahradnik	66602f4af6	Update language_cz.h ... New strings: #define MSG_HALTED #define MSG_PLEASE_RESET Some texts shortened for smaller displays.	2016-07-10 13:25:50 +02:00
Petr Zahradnik	eaf9e615ce	Total print time for LCD correction (hours:minutes format)	2016-07-10 13:08:05 +02:00
esenapaj	9e56d5825e	Adjust spacing	2016-07-10 14:25:29 +09:00
esenapaj	5832f4b848	Follow-up the PR #4253 (Runout Sensor without SD Card, Print Timer support in M104) ... ・Update forgotten example configuration files	2016-07-10 14:24:57 +09:00
Scott Lahteine	77283f5bf0	Merge pull request #4245 from thinkyhead/rc_simpler_therm_check ... Simpler/extensible thermistor test in thermistortables.h	2016-07-09 21:13:42 -07:00
Scott Lahteine	f9e08b1fcd	Merge pull request #4254 from AnHardt/killscreen ... Add a kill-screen	2016-07-09 20:44:42 -07:00
AnHardt	faac2bcfdb	Add a kill-screen	2016-07-10 04:50:45 +02:00
Scott Lahteine	3b3e52616c	Merge pull request #4253 from thinkyhead/rc_clexpert_runout ... Runout Sensor without SD Card, Print Timer support in M104	2016-07-09 19:10:36 -07:00
Scott Lahteine	aa3ab93971	Merge pull request #4240 from AnHardt/sampler-8-7-16 ... Today's fix and cleanup collection	2016-07-09 19:09:45 -07:00
Scott Lahteine	4cd045791c	Reduce code size by trusting the compiler	2016-07-09 18:17:44 -07:00
Scott Lahteine	a8538bd7ce	General cleanup, code reduction in Marlin_main.cpp	2016-07-09 18:17:44 -07:00
Scott Lahteine	1026e5b071	Replace PLA/ABS preheating with generic	2016-07-09 18:06:51 -07:00
Petr Zahradnik	e282d69f63	Print job timer comment changed	2016-07-09 17:57:54 -07:00
Petr Zahradnik	a2159cfbc3	Error message change in SanityCheck.h	2016-07-09 17:57:54 -07:00
Petr Zahradník junior	315b4c2153	Runout sensor without SD Card	2016-07-09 17:57:53 -07:00
Scott Lahteine	51c9c3fe2c	Indentation in MarlinSerial.cpp	2016-07-09 17:57:53 -07:00
Scott Lahteine	e03414b2dd	Simpler/extensible thermistor test in thermistortables.h	2016-07-08 19:54:45 -07:00
AnHardt	4b44a23a36	Add TX-buffer for MarlinSerial ... Similar to the current Arduino HardwareSerial but with max. 256 byte buffer-size. Deactivated by default. The boards with AT90USB processor (USBCON) already use a TX-buffer.	2016-07-08 17:25:21 +02:00
AnHardt	468f7f03a2	homeaxis() can leave early ... when no known axis needs to be homed. Most changes are only caused from altering the indentation. ``` if (axis == X_AXIS ? HOMEAXIS_DO(X) : axis == Y_AXIS ? HOMEAXIS_DO(Y) : axis == Z_AXIS ? HOMEAXIS_DO(Z) : 0) { ... } to if (!(axis == X_AXIS ? HOMEAXIS_DO(X) : axis == Y_AXIS ? HOMEAXIS_DO(Y) : axis == Z_AXIS ? HOMEAXIS_DO(Z) : 0)) return; ... ```	2016-07-08 15:59:33 +02:00
AnHardt	eff7912243	Ensble/disable hardware endstops in G28 globally. ... For moving away from the endstops we do not have to disable them. They are not tested anyway.	2016-07-08 15:49:10 +02:00
AnHardt	f69434d81c	Eliminate void setup_for_endstop_move()	2016-07-08 15:23:20 +02:00
AnHardt	0ea6247fc2	Use logic in Z_SAFE_HOMING ... Use logic in Z_SAFE_HOMING From ``` if (home_all_axis || homeZ) { if (home_all_axis) { ... home z } else if (homeZ) { // Don't need to Home Z twice home z } } ``` to ``` if (home_all_axis || homeZ) { if (home_all_axis) { ... } home z } ```	2016-07-08 15:08:50 +02:00
AnHardt	de3a169336	Always define MIN_Z_HEIGHT_FOR_HOMING even if 0 ... Always define MIN_Z_HEIGHT_FOR_HOMING even if 0 Always make a potential rise to `home_offset[Z_AXIS]` possible in G28. Get rid of some very ugly constructs in MBL (ultralcd.cpp).	2016-07-08 15:08:32 +02:00
AnHardt	88ed232f53	Remove HAS_BED_PROBE case in first raise in G28 ... Differentiating made sense here when we could save a dozen lines of code, but not for one line.	2016-07-08 14:59:44 +02:00
AnHardt	653eff3b31	Clean up quick_home_xy() ... Since we do the actual homing now in the 'normal' routines `quick_home_xy()` can be simplified to a relative simple diagonal move.	2016-07-08 14:59:27 +02:00
Scott Lahteine	98d0167a57	Merge pull request #4226 from thinkyhead/rc_emergency_command_parser ... MarlinSerial emergency-command parser (with M108)	2016-07-07 16:53:55 -07:00
Scott Lahteine	2ee4e4f791	Make wait_for_heatup volatile	2016-07-07 16:37:23 -07:00
Scott Lahteine	bd5a825b8b	Wait for end of line before invoking action	2016-07-07 16:37:23 -07:00
Scott Lahteine	ea47803ae2	Simplify emergency parser (only parse initial command)	2016-07-07 16:37:22 -07:00
Scott Lahteine	834ad14c8d	Add quickstop_stepper to update current position with stepper.quick_stop()	2016-07-07 16:37:22 -07:00
Scott Lahteine	ecffe92e20	Group EMERGENCY_PARSER commands	2016-07-07 16:37:22 -07:00
AnHardt	a129078927	Add an emergency-command parser to MarlinSerial (supporting M108) ... Add an emergency-command parser to MarlinSerial's RX interrupt. The parser tries to find and execute M108,M112,M410 before the commands disappear in the RX-buffer. To avoid false positives for M117, comments and commands followed by filenames (M23, M28, M30, M32, M33) are filtered. This enables Marlin to receive and react on the Emergency command at all times - regardless of whether the buffers are full or not. It remains to convince hosts to send the commands. To inform the hosts about the new feature a new entry in the M115-report was made. "`EMERGENCY_CODES:M112,M108,M410;`". The parser is fast. It only ever needs two switch decisions and one assignment of the new state for every character. One problem remains. If the host has sent an incomplete line before sending an emergency command the emergency command could be omitted when the parser is in `state_IGNORE`. In that case the host should send "\ncommand\n" Also introduces M108 to break the waiting for the heaters in M109, M190 and M303. Rename `cancel_heatup` to `wait_for_heatup` to better see the purpose.	2016-07-07 16:37:22 -07:00
Scott Lahteine	9f42b1a075	Merge pull request #4235 from thinkyhead/rc_revert_quickhome_test ... Fix quick homing, tweak MIN_Z_HEIGHT_FOR_HOMING	2016-07-07 13:37:14 -07:00
Scott Lahteine	ad968f2325	Merge pull request #4234 from thinkyhead/rc_better_position_logging ... Move XYZ in print_xyz and DEBUG_POS to the front	2016-07-07 12:31:15 -07:00
Scott Lahteine	4036c73cdd	Don't raise Z if only homing Z	2016-07-07 12:28:37 -07:00
Scott Lahteine	0b6f8f8244	Apply MIN_Z_HEIGHT_FOR_HOMING raise literally	2016-07-07 12:25:02 -07:00
Scott Lahteine	177ec20bf0	Revert quick-home changes	2016-07-07 12:17:34 -07:00
Scott Lahteine	9c5b462ef2	Move XYZ in print_xyz and DEBUG_POS to the front	2016-07-07 11:42:19 -07:00
Scott Lahteine	4e84c803a3	Merge pull request #4232 from thinkyhead/rc_no_axis_codes_needed ... Don't use axis_codes if a literal will do	2016-07-06 20:05:16 -07:00
Scott Lahteine	e2f7cb0905	Don't use axis_codes if a literal will do	2016-07-06 18:37:21 -07:00
Scott Lahteine	6559f7359f	Fix comment on Z raise for homing, save a few bytes	2016-07-06 16:21:51 -07:00
Scott Lahteine	799c60cadc	Merge pull request #4217 from thinkyhead/rc_fix_homing_raise ... Don't do_probe_raise with MIN_Z_HEIGHT_FOR_HOMING	2016-07-06 14:39:37 -07:00
Scott Lahteine	d7e9647505	Sanity Check for probe raises	2016-07-06 13:46:06 -07:00
Scott Lahteine	d0b29cabf3	Don't re-home X and Y if you quick homed	2016-07-06 13:46:06 -07:00
Scott Lahteine	e0a6b978f5	Don't do_probe_raise with MIN_Z_HEIGHT_FOR_HOMING	2016-07-06 13:46:05 -07:00
Philip Schell	cf8ec1216a	Update language_de.h for German translation ... @MarlinFirmware/language-team my changes for the German language. Feel free to improve :)	2016-07-06 21:44:16 +02:00
petrzjunior	b81b77111b	Update language_cz.h	2016-07-06 21:04:34 +02:00
Scott Lahteine	7735ec5e7a	Merge pull request #4223 from thinkyhead/rc_rename_heatup ... Change cancel_heatup to wait_for_heatup	2016-07-06 11:25:44 -07:00
Scott Lahteine	160a2be117	Change cancel_heatup to wait_for_heatup	2016-07-06 09:17:50 -07:00
AnHardt	16c83d203b	Make use of the good features of a sled probe for all probes. ... Move and extend axis_unhomed test to deploy/stow_z_probe(). Move and extend position store/restore to deploy/stow_z_probe(). Now all kinds of probes can use the 'E' parameter in G29/M48. Allen key probes can be used now for grid and 3-point levelling. Deploying the Allen Key probe uses big moves in z direction. Too dangerous for an unhomed z-axis. Throw a compile time error when we try to configure an Allen Key probe homing to z-min and having no other z-min-endstop.	2016-07-06 04:11:04 +02:00
AnHardt	8555816a11	Generalize and simplify 'triggered when stowed test` ... The `PROBE_IS_TRIGGERED_WHEN_STOWED_TEST` is able to detect if a probe is successfully deployed/stowed. It was part of the Allen Key probes code only. Now the function is generally available. Currently this test is compulsory for Allen Key probes to not alter the used behaviour If you want to add the test for an other type of probe simply add ``` #define PROBE_IS_TRIGGERED_WHEN_STOWED_TEST ``` to your config.	2016-07-06 03:56:17 +02:00
AnHardt	5126cce7fd	Move Allen Key probe move scripts to their own functions ... There was an hidden extra move after the scripts. This is configurable now. Added the extra moves to the relevant configs.	2016-07-06 03:46:40 +02:00
AnHardt	7d063c111c	Add a optional feedrate parameter to do_blocking_move() ... Add a optional feedrate parameter to `do_blocking_move()` and its companions.	2016-07-06 03:46:34 +02:00
Scott Lahteine	b114b6a0b3	Save 152 bytes using uint8_t for command indices	2016-07-05 16:29:28 -07:00
Scott Lahteine	0d4ff0c48b	Allow the queue to be cleared from within commands	2016-07-05 16:25:20 -07:00
Scott Lahteine	c450851401	Merge pull request #4209 from AnHardt/too-high-G28 ... Make raise for probe deploy relative in homeaxis()	2016-07-05 11:07:42 -07:00
AnHardt	f799f18388	MBL typo	2016-07-05 18:19:53 +02:00
AnHardt	8b02e68cb6	Make raise for probe deploy relative in homeaxis() ... Make raise for probe deploy relative in homeaxis() by setting `current_position[axis]` to zero later.	2016-07-05 10:42:33 +02:00
Scott Lahteine	e48502866b	Merge pull request #3611 from alephobjects/M108_cancel_heatup ... Introduce M108 cancel wait for heatup/cooldown of the hotend and bed	2016-07-04 01:19:31 -07:00
Scott Lahteine	d70197f514	Merge pull request #4204 from thinkyhead/rc_fix_gcode_t_position ... Additional patches for gcode_T position change	2016-07-04 01:16:22 -07:00
Scott Lahteine	869b517589	Merge pull request #4205 from thinkyhead/rc_fixup_unit_references ... References to millimeters in code comments need an update	2016-07-04 01:15:34 -07:00
Scott Lahteine	e104b91ea6	References to millimeters in code comments need an update	2016-07-03 20:13:29 -07:00
AnHardt	ff91d28a3a	Remove wants_to_cool warning ... Remove wants_to_cool warning	2016-07-04 03:12:11 +02:00
Scott Lahteine	c9e536cf87	Additional patches for gcode_T position change	2016-07-03 18:11:02 -07:00
Scott Lahteine	60865fc45b	Merge pull request #4202 from thinkyhead/rc_fix_gcode_t_position ... Fix position adjustment with gcode_T and MBL	2016-07-03 17:55:43 -07:00
Scott Lahteine	f841038313	Merge pull request #4201 from thinkyhead/rc_info_fit ... Shorter labels for Print Stats info	2016-07-03 17:47:00 -07:00
Scott Lahteine	f31af61ee2	Fix position adjustment with gcode_T and MBL	2016-07-03 17:44:04 -07:00
Scott Lahteine	a8f5c2bf96	Merge pull request #4192 from birkett/k8400 ... Add Velleman K8400 board support.	2016-07-03 17:41:13 -07:00
Scott Lahteine	ef8980bfa0	Shorter labels for Print Stats info	2016-07-03 16:00:24 -07:00
Scott Lahteine	2ed625dafa	Fix compiler warnings for static screens	2016-07-03 15:26:17 -07:00
Anthony Birkett	e77844594d	readme.md -> README.md	2016-07-03 22:15:24 +01:00
Anthony Birkett	a0b00d29e3	Add a ported example configuration for the Velleman K8400 (Vertex) printer. ... Supports both dual and single head printers (with the correct config). Includes community sourced feed rate fix. Rename / move files. Remove redundant definitions.	2016-07-03 22:09:08 +01:00
lrpirlet	9b42c6b44b	apply correction when swtiching from MBL to physical in G28 X	2016-07-03 21:43:42 +02:00
Andrea Cimbalo	46196e9ee5	Add working PlatformIO support	2016-07-03 15:33:24 +02:00
esenapaj	95347fc650	Follow-up the PR #3662 (Rewritten FILAMENT_CHANGE_ENABLE feature) ... ・Update a forgotten Configuration_adv.h of Cartesio	2016-07-03 09:04:29 +09:00
Scott Lahteine	a06c5165a7	Shorter strings for smaller LCDs	2016-07-02 15:47:16 -07:00
Scott Lahteine	982f10e6a0	Use STATIC_ITEM for LCD message display	2016-07-02 15:47:15 -07:00
Petr Zahradnik	43ff0ce35f	Rewritten FILAMENT_CHANGE_ENABLE feature	2016-07-02 15:34:33 -07:00
Scott Lahteine	51b7820686	Patch up About Printer sub-menus	2016-07-02 15:22:34 -07:00
Scott Lahteine	439e78147d	Static menu items take an optional string, LJ by default	2016-07-02 15:22:34 -07:00
Scott Lahteine	fa9b2a925d	Tweak spacing in printcounter.cpp	2016-07-02 15:22:33 -07:00
Scott Lahteine	dbfc87cdcf	Squish sanity check for build info	2016-07-02 15:22:33 -07:00
Anthony Birkett	7a377c1d75	Add "About Printer" information menu. ... Includes: *firmware version / branch / date. *extruder count *board information (name, serial details, power supply type) *thermistors (names, min/max temperatures) *printer statistics (PRINTCOUNTER details) Thanks to @thinkyhead for contributions.	2016-07-02 15:22:26 -07:00
Scott Lahteine	77a923d8ce	Merge pull request #4186 from thinkyhead/rc_array_macros ... Simplified variable-size array macros	2016-07-01 20:48:12 -07:00
Scott Lahteine	e650a75b88	Simplified variable-size array macros	2016-07-01 20:36:05 -07:00
Scott Lahteine	ac4f235912	Merge pull request #4167 from thinkyhead/rc_eeprom_checksum ... EEPROM Checksum	2016-07-01 19:22:49 -07:00
esenapaj	03b8f88092	Tab to Space	2016-07-02 08:07:33 +09:00
AnHardt	cb1b31f69b	Unconditional do_probe_raise() in probe_pt() ... If Z_RAISE_BETWEEN_PROBINGS is null or undefined the probe is currently not raised by home_offset[Z_AXIS] and zprobe_zoffset. But when different from 0 is. If an undefined Z_RAISE_BETWEEN_PROBINGS expands to 0 (and it does) this is the solution. A similar asymmetry exists with the newly introduced 'short-cut' in G28 - but its the rise before anything is probed - so should not make a difference.	2016-07-01 15:28:41 +02:00
Scott Lahteine	7ef7843fd4	Merge pull request #4181 from thinkyhead/rc_rename_a_move_func ... Do interpolated moves for Allen Key deploy/stow	2016-06-30 16:30:09 -07:00
Scott Lahteine	6b2a7b30af	Extra comments to clarify EEPROM code	2016-06-30 16:28:01 -07:00
Scott Lahteine	787f394676	MAX_EXTRUDERS replaces mysterious "4"	2016-06-30 16:27:37 -07:00
Scott Lahteine	bc3748b7bc	Add shared Config_Postprocess for Read and Reset	2016-06-30 16:25:29 -07:00
Scott Lahteine	adcd0f5de3	Some formatting in configuration_store.cpp	2016-06-30 16:25:29 -07:00
Scott Lahteine	5e370006fc	EEPROM Checksum	2016-06-30 16:20:25 -07:00
Scott Lahteine	725fde8b26	Merge pull request #4169 from thinkyhead/rc_wait_but_break ... Allow wait-for-cooling, break at threshold or if cooling stalls	2016-06-30 16:13:51 -07:00
Scott Lahteine	da6b0dab5f	Use prepare_move_to_destination for Allen Key deploy/stow	2016-06-30 16:09:43 -07:00
Scott Lahteine	c42f8fb8dd	Rename some movement sub-functions	2016-06-30 15:50:00 -07:00
Scott Lahteine	b6b3a4afbf	Merge pull request #4168 from thinkyhead/rc_viki2_for_ramps ... Support for VIKI2 in RAMPS and derivatives	2016-06-30 01:48:50 -07:00
Scott Lahteine	f84d85f761	Cleanup extruder runout configs	2016-06-30 01:40:41 -07:00
Scott Lahteine	5e14a528dd	Always wait for cooling in M109/M190, break at low temp or if cooling stalls	2016-06-29 14:07:54 -07:00
Scott Lahteine	0b0b7aac6e	Support for VIKI2 in RAMPS and derivatives	2016-06-28 18:19:18 -07:00
Scott Lahteine	abda4ab427	Clean up CNControls pins	2016-06-28 16:56:48 -07:00
Scott Lahteine	683975cf90	Fix spelling in a config comment	2016-06-28 16:49:13 -07:00
Scott Lahteine	8268c0a9a0	Always define temp sensor, heater pins for RUMBA	2016-06-28 16:28:05 -07:00
Scott Lahteine	db19959735	Merge pull request #4161 from thinkyhead/rc_general_cleanup ... Reduce storage requirements for strings, make some PGM	2016-06-27 20:46:26 -07:00
Scott Lahteine	2e96276bf4	More debug message cleanup	2016-06-27 20:36:19 -07:00
Scott Lahteine	dc2c0e5e24	Simpler debug output for deploy/stow	2016-06-27 20:36:18 -07:00
Scott Lahteine	bd491818d6	Reduce storage requirements for strings, make some PGM	2016-06-27 20:36:18 -07:00
Scott Lahteine	ee876dcd7a	Merge pull request #4159 from thinkyhead/rc_rigidbot_diff ... Rigidbot V2 support - has MCP4728 digipot	2016-06-27 20:35:22 -07:00
Scott Lahteine	0c24e0e445	Support for newer Wire library	2016-06-27 20:25:03 -07:00
Scott Lahteine	ddb386c139	Init DAC_DISABLE_PIN in dac_init	2016-06-27 20:25:03 -07:00
AnHardt	e480ee0054	Further cleanup of G28 for probes	2016-06-27 20:19:51 -07:00
AnHardt	39883d03fc	universalize axis_unhomed_error()	2016-06-27 20:19:51 -07:00
AnHardt	e616093d4c	Simplify dock_sled() ... `dock_sled()` is never called with offset parameter - remove it. We move x only - so only that needs to be homed. Consequence is - we can home to z-min now with a sled probe! Feedrates are set and restored in `do_blocking_move()`. We already checked if the probe is deployed/stowed in deploy/stow_probe. ``` if (z_loc < _Z_RAISE_PROBE_DEPLOY_STOW + 5) z_loc = _Z_RAISE_PROBE_DEPLOY_STOW; ``` makes no sense - remove. Now the raise is the same for deploy/stow -> move before the if. Replace the if with a ternary. Instead writing LOW/HIGH use the boolean `stow` we already have. There is no reason for not using the sled probe in G29/M48 with 'E'. It takes a while but works. (tested!)	2016-06-27 20:19:51 -07:00
Scott Lahteine	6c60869409	Support DAC_OR_ADDRESS in Printrboard too	2016-06-27 12:36:21 -07:00
Scott Lahteine	593c8bf286	Support for Rigidbot V2	2016-06-27 12:35:20 -07:00
Scott Lahteine	511503ede9	CARTESIO_UI has lcd contrast	2016-06-27 12:04:49 -07:00
Scott Lahteine	829c92f1ba	Use Z_RAISE_BETWEEN_PROBINGS with MBL	2016-06-26 15:39:11 -07:00
Scott Lahteine	eb1755208f	Merge pull request #4153 from thinkyhead/rc_probe_raise_options ... Combine Z raise before/after options	2016-06-26 15:30:08 -07:00
Scott Lahteine	10da7ac86c	Combine Z raise before/after options	2016-06-26 13:56:30 -07:00
Scott Lahteine	9caa8941e2	Merge pull request #4149 from thinkyhead/rc_minimum_raise_in_probe_pt ... Ensure a minimum height before XY move in probe_pt	2016-06-25 19:35:58 -07:00
Scott Lahteine	3fa631130f	Ensure a minimum height before XY move in probe_pt	2016-06-25 19:19:31 -07:00
Scott Lahteine	a7684eef7a	Squish code in ST7920	2016-06-25 18:35:15 -07:00
AnHardt	b4076883cc	Set testet delays for K8200, RAMBO, MINIRAMBO and ST7920	2016-06-25 18:35:15 -07:00
AnHardt	4454d80276	Decrease the needed nops to 1 ... by shitfing the left shift into the high phase. ``` 2 cbi 0x2,1 ;set CLK // 1 in r18,__SREG__ //1 1-3 sbrc r24,7 //2-4 2 rjmp .L19 //4 1 cli .L19: //5 2 lds r25,258 lds r25,258 //7 1 andi r25,lo8(-2) ori r25,lo8(1) //8 2 sts 258,r25 sts 258,r25 //10 1 out __SREG__,r18 out __SREG__,r18 //11 2 .L3: rjmp .L3 //13 //2 2 sbi 0x2,1 ;reset CLK // //13-15 //2-4 1 lsl r24 ; val //1 1 nop //2 2 cbi 0x2,1 ;set CLK //4 ... ```	2016-06-25 18:35:15 -07:00
AnHardt	56c42b572c	3 ms speedup for ST7920 and delay for BOARD_3DRAG ... and saving ~1k memory by limiting the `#pragma GCC optimize (3)` optimisation to `ultralcd_st7920_u8glib_rrd.h`. These optimisation was and is not done for all the other displays, is the reason for the big additionally use of memory, because the complete 'ultralcd.cpp' and 'dogm_lcd_implementation.h' was optimised (sadly i did not observe a change in speed). Unrolling the loop in `ST7920_SWSPI_SND_8BIT()`, what i expected the optimiser to do, by hand, saved some speed by eliminating the loop variable (i) compares and increases. Every CPU cycle in this loop costs at least 0.5ms per display update because it's executed more than 1k times/s. The delays are now pre-filled with the calculated values for 4.5V driven ST7920. A way to simply add __your__ timing into the configuration was made. At 4.5V 1.) The CLK signal needs to be at least 200ns high and 200ns low. 2.) The DAT pin needs to be set at least 40ns before CLK goes high and must stay at this value until 40ns after CLK went high. A nop takes one processor cycle. For 16MHz one nop lasts 62.5ns. For 20MHz one not lasts 50ns. To fulfill condition 1.) we need 200/62.5 = 3.2 => 4 cycles (200/50 = 4 => 4). For the low phase, setting the pin takes much longer. For the high phase we (theoretically) have to throw in 2 nops, because changing the CLK takes only 2 cycles. Condition 2.) is always fulfilled because the processor needs two cycles (100 - 125ns) for switching the CLK pin. Needs tests and feedback. Especially i cant test 20MHz, 3DRAG and displays supplied wit less than 5V. Are the delays right? Please experiment with longer or shorter delays. And give feedback. Already tested are 5 displays with 4.9V - 5.1V at 16MHz where no delays are needed.	2016-06-25 18:35:15 -07:00
Scott Lahteine	ca184d3d72	Merge pull request #4147 from thinkyhead/rc_fix_M48_raise ... Fix debug output in probe_pt	2016-06-25 18:15:33 -07:00
Scott Lahteine	b4161cbd98	Fix debug output in probe_pt	2016-06-25 17:59:03 -07:00
Edward Patel	da88b00585	MBL: Add support for max z endstop ... See https://github.com/MarlinFirmware/Marlin/issues/4088	2016-06-25 21:58:02 +02:00
Scott Lahteine	74878d1f16	Always do a brief delay in lcd_quick_feedback	2016-06-24 14:46:10 -07:00
Scott Lahteine	7de7552069	Merge pull request #4133 from MagoKimbra/Single_home_axis_delta ... Single home Axis Delta need simple sync_plan_position	2016-06-23 21:14:22 -07:00
Scott Lahteine	15a6b49f37	Simplified probe_pt (in G30)	2016-06-23 20:25:46 -07:00
Scott Lahteine	6a7045b9bf	Remove clean_up_after_endstop_move	2016-06-23 20:23:19 -07:00
Scott Lahteine	2a4f866561	Simplified probe_pt (in G29)	2016-06-23 20:22:28 -07:00
Scott Lahteine	89a2aa026b	Simplified probe_pt (in M48)	2016-06-23 19:22:45 -07:00
Scott Lahteine	f8530c5d1f	Simplified probe_pt function (G28 grid)	2016-06-23 19:09:32 -07:00
Scott Lahteine	c376c08042	Simplified probe_pt function (part 1)	2016-06-23 19:00:29 -07:00
Scott Lahteine	9a71b7f8ad	Fix debug message for 3-point leveling	2016-06-23 18:17:31 -07:00
Scott Lahteine	550c03a5a9	Drop raise_z_after_probing function	2016-06-23 18:11:54 -07:00
Scott Lahteine	bb38c816af	Always raise in deploy_z_probe / stow_z_probe	2016-06-23 18:00:20 -07:00
Scott Lahteine	68f3350050	Cleanup M401 / M402	2016-06-23 17:04:41 -07:00
Scott Lahteine	3afda99adf	Regular handlers for G31 / G32	2016-06-23 17:04:13 -07:00
Scott Lahteine	6803c8e37e	Move Z up before, or down after XY, for "blocking move"	2016-06-23 15:50:13 -07:00
Scott Lahteine	03c70c1990	SERVO_DEACTIVATION_DELAY => SERVO_DELAY	2016-06-23 14:33:29 -07:00
MagoKimbra	570f3bbc07	Single home Axis Delta need simple sync_plan_position	2016-06-23 23:09:47 +02:00
Scott Lahteine	61f34eec03	Merge pull request #4125 from jbrazio/bugfix/planner-warning ... Fixes some compiler warnings	2016-06-22 19:34:37 -07:00
Scott Lahteine	bdcd628896	Merge pull request #4126 from thinkyhead/rc_lin_timing_patch ... Patch LIN_ADVANCE timing issue	2016-06-22 19:24:44 -07:00
João Brázio	664232140d	Fixes somes compiler warnings	2016-06-23 03:12:55 +01:00
Sebastianv650	0c5192b288	Patch LIN_ADVANCE timing issue ... Also the extruder stepper ISR has to keep an eye on step_loops count.	2016-06-22 19:05:14 -07:00
Scott Lahteine	d4134e6901	Define Z_SAFE_HOMING point when Z_PROBE_SLED is activated alone	2016-06-22 17:51:32 -07:00
Scott Lahteine	7b2fadd598	Apply some fixes from Andreas ... Derived from https://github.com/AnHardt/Marlin/commit/6e8ede8c694fa4d9e3c769840b09d56 7f8d8e0dd	2016-06-22 17:35:59 -07:00
Scott Lahteine	bd01592816	Goodbye MECHANICAL_PROBE	2016-06-22 17:13:33 -07:00
Scott Lahteine	2640d13a9f	Simplify initial raise in M48	2016-06-22 16:53:04 -07:00
Scott Lahteine	3763d45656	Return Z position in run_z_probe	2016-06-22 16:52:32 -07:00
Scott Lahteine	1f48b5c30f	Pass a raise to probe_pt, not a Z position	2016-06-22 16:40:21 -07:00
Scott Lahteine	6fdd5ba246	Save and restore feedrate in more places	2016-06-22 16:40:20 -07:00
Scott Lahteine	fe173c2bc6	Generalized probe raise, use for after probing	2016-06-22 14:44:30 -07:00
Scott Lahteine	7da3080761	Simpler cleanup in G28 / G29	2016-06-22 14:44:30 -07:00
Scott Lahteine	15229d988b	Fix compile error for bed matrix in M48	2016-06-22 14:04:46 -07:00
Scott Lahteine	c01352cbd5	Add a dependency for z servo macros	2016-06-22 14:04:23 -07:00
Scott Lahteine	c3794bd695	Add HAS_PROBING_PROCEDURE conditional	2016-06-22 14:03:22 -07:00
Scott Lahteine	42ce60c5cc	Make sure NUM_SERVOS is set for Z servo endstop	2016-06-22 14:01:19 -07:00
Scott Lahteine	b590a7dee0	Make Z_RAISE_BETWEEN_PROBINGS a more general option	2016-06-22 14:00:44 -07:00
Scott Lahteine	bb9c67b4b5	Tweak some feedrate vars	2016-06-22 03:27:31 -07:00
Scott Lahteine	5158bd6e93	Screen out G29 E for sled and allen key, allow single probe	2016-06-22 03:20:33 -07:00
Scott Lahteine	ccae92588d	Cleanup debug in G28 and G29	2016-06-22 03:20:33 -07:00
Scott Lahteine	b4a9d2366c	Use a macro for kinematic sync_plan_position	2016-06-22 03:20:33 -07:00
Scott Lahteine	bfccf26294	Use sync_plan_position_delta where needed	2016-06-22 03:20:33 -07:00
Scott Lahteine	a6b8c67df4	Move probe deploy after setup call in G29	2016-06-22 03:20:33 -07:00
Scott Lahteine	e69916d1bd	Split up endstop_move functions	2016-06-22 03:20:33 -07:00
Scott Lahteine	0e18a4897b	Simpler handling of sled/allen-key in probe_pt	2016-06-22 03:20:33 -07:00
Scott Lahteine	1a92e2ef18	Comment on run_z_probe	2016-06-22 03:20:33 -07:00
Scott Lahteine	68e0e5855e	For all probes, at the end of G29 simply raise and stow	2016-06-22 03:20:33 -07:00
Scott Lahteine	c3023f8cc5	Make M401/M402 available with HAS_BED_PROBE	2016-06-22 03:20:33 -07:00
Scott Lahteine	9f0c255c69	Show uncorrected position in set_bed_level_equation_3pts	2016-06-22 03:20:33 -07:00
Scott Lahteine	07298ac992	Initialize current_position to home_offset on boot	2016-06-22 03:20:33 -07:00
Scott Lahteine	d50539583a	Make XY_PROBE_SPEED a general probe option	2016-06-22 03:04:47 -07:00
Scott Lahteine	2798499b71	XY_TRAVEL_SPEED => XY_PROBE_SPEED	2016-06-22 02:45:25 -07:00
Scott Lahteine	88dc543584	Add a macro for XY_TRAVEL_FEEDRATE	2016-06-22 02:23:50 -07:00
Scott Lahteine	117db77c55	make motor_current_setting static and constexpr	2016-06-21 19:50:08 -07:00
João Brázio	19fb04d761	Update bq Hephestos 2 config	2016-06-21 18:15:51 -07:00
Scott Lahteine	b0e47608e6	Merge pull request #4108 from esenapaj/Fix-for-PR-#4093 ... Fix for PR #4093 (Make Z Probe options independent of ABL), etc	2016-06-21 18:12:08 -07:00
Scott Lahteine	c84732e605	Merge pull request #4111 from esenapaj/Cosmetic-changes-and-small-fix-for-thermistortables.h ... Cosmetic changes and small fix for thermistortables.h	2016-06-21 18:05:32 -07:00
Scott Lahteine	cdc661ea5e	Merge pull request #4110 from esenapaj/Small-cosmetic-changes-for-language-files ... Small cosmetic changes for language files	2016-06-21 18:04:12 -07:00
Scott Lahteine	c8186e9423	Merge pull request #4109 from esenapaj/Enclose-#error-string-by-double-quotes ... Enclose #error string by double-quotes	2016-06-21 18:03:30 -07:00
Scott Lahteine	40cd20a236	Fix comments on EXPERIMENTAL_I2CBUS	2016-06-21 17:58:44 -07:00
esenapaj	385945ca31	Cosmetic changes and small fix for thermistortables.h ... ・Adjust spacing ・Standardize comments position ・Remove ',' at the tail of array	2016-06-21 21:19:47 +09:00
esenapaj	fac58f0291	Cosmetic changes for language files	2016-06-21 21:13:25 +09:00
esenapaj	14b661b9e5	Enclose #error string by double-quotes	2016-06-21 21:06:14 +09:00
esenapaj	d583ea852d	Standardize format description of Panel	2016-06-21 20:51:27 +09:00
esenapaj	aa6d35bd49	Move code block of probe to appropriate position	2016-06-21 20:36:46 +09:00
esenapaj	740fb2ce39	Adjust spacing	2016-06-21 19:37:45 +09:00
esenapaj	f77f3ffa70	Remove duplicated Z_PROBE_OFFSET_RANGE_MIN, Z_PROBE_OFFSET_RANGE_MAX	2016-06-21 19:33:45 +09:00
Scott Lahteine	19fe93a5a9	Clean up configs for Z_MIN_PROBE_REPEATABILITY_TEST	2016-06-21 03:10:46 -07:00
Scott Lahteine	71a7408012	Merge pull request #4106 from thinkyhead/rc_temp_compile_err ... Fix compile error with watch_bed_next_ms	2016-06-21 02:48:46 -07:00
Scott Lahteine	dcb8ec32ee	Fix compile error with watch_bed_next_ms	2016-06-21 02:13:41 -07:00
Scott Lahteine	3996242e9d	Allow Z_MIN_PROBE_REPEATABILITY_TEST solo	2016-06-21 01:56:40 -07:00
Scott Lahteine	26a9cd0b08	Move run_z_probe to earlier block	2016-06-21 01:25:23 -07:00
Scott Lahteine	7f8a2025af	Move raise_z_after_probing into earlier block	2016-06-21 01:03:40 -07:00
Scott Lahteine	2530371516	Always disable probe at the end of G29	2016-06-20 16:40:44 -07:00
Scott Lahteine	6aba98e470	Comment on setup_for_endstop_move	2016-06-20 16:40:44 -07:00
Scott Lahteine	04e88d008e	Clear up ordering in G30	2016-06-20 16:40:44 -07:00
Scott Lahteine	ed75b0ea11	Make clean_up function available for probes	2016-06-20 16:28:45 -07:00
Scott Lahteine	51d52cb52a	Make run_z_probe available for any bed probe	2016-06-20 16:02:36 -07:00
Scott Lahteine	f6b09cf465	Always use deploy/stow for dock_sled	2016-06-20 15:51:01 -07:00
Scott Lahteine	3b457c2dd3	Use deploy/stow with FIX_MOUNTED_PROBE too	2016-06-20 15:25:01 -07:00
Scott Lahteine	7e9d4a68d4	Always raise Z (if needed) for servo deploy/stow	2016-06-19 20:17:13 -07:00
Scott Lahteine	9beb3f2f5e	Merge pull request #4097 from thinkyhead/rc_fil_runout_cleanup ... FIL_RUNOUT_INVERTING false by default	2016-06-19 19:46:14 -07:00
Scott Lahteine	f215b30932	Merge pull request #4093 from thinkyhead/rc_probe_without_abl ... Make Z Probe options independent of ABL	2016-06-19 19:44:25 -07:00
Scott Lahteine	2fd2301928	FILRUNOUT => FIL_RUNOUT	2016-06-19 19:25:26 -07:00
Scott Lahteine	dfbf8b3c2c	FIL_RUNOUT_INVERTING false by default	2016-06-19 19:25:26 -07:00
Scott Lahteine	7b5cd314a5	Merge pull request #4095 from thinkyhead/rc_fil_runout_cleanup ... Improve FILAMENT_RUNOUT_SENSOR, FILRUNOUT_PIN	2016-06-19 18:48:18 -07:00
Scott Lahteine	de12228758	Make Z Probe options independent of ABL	2016-06-19 18:47:27 -07:00
Scott Lahteine	add0032820	Improve FILAMENT_RUNOUT_SENSOR, FILRUNOUT_PIN	2016-06-19 18:13:33 -07:00
Scott Lahteine	f8c278ce4d	Cartesio UI display option in all configs	2016-06-19 17:39:46 -07:00
Scott Lahteine	400e13d136	Output a message for SD read errors	2016-06-19 17:14:56 -07:00
Roxy-3D	96b8bcca84	Merge pull request #4081 from thinkyhead/rc_tweaky_m48_tweaks ... Cleanup of M48	2016-06-18 22:21:16 -05:00
Scott Lahteine	b7e3c1bbc4	Tweak M48 output conditions	2016-06-18 16:17:53 -07:00
Scott Lahteine	1dad912b03	Adjust M48 raise / move handling	2016-06-18 15:38:24 -07:00
Scott Lahteine	46d3ef2223	Simplify sample_set probe_pt call in M48	2016-06-18 15:38:23 -07:00
Scott Lahteine	a647b05f82	Shrink some debug code in G28	2016-06-18 15:38:23 -07:00
Scott Lahteine	4edf813bde	Just-in-time declaration style in M48	2016-06-18 15:38:23 -07:00
Juan Ricardo Gomez Anaya	c475291e19	Fix M851 ... Minor change missing in the process of standardize the gcode M851	2016-06-18 15:19:07 -07:00
Scott Lahteine	e35583888c	Merge pull request #4082 from esenapaj/Follow-up-the-PR-#4065 ... Follow-up the PR #4065 (Remove support for XY servo endstops)	2016-06-18 03:31:12 -07:00
Scott Lahteine	6dff52d920	Merge pull request #4078 from RicardoGA/Language_Spanish ... Update Spanish Language	2016-06-18 03:28:46 -07:00
esenapaj	d55b94d606	Follow-up the PR #4065 (Remove support for XY servo endstops) ... ・Update a forgotten Configuration.h of Cartesio	2016-06-18 18:01:58 +09:00
Scott Lahteine	4e860babbc	Allow setting xy_travel_speed for delta leveling also	2016-06-18 01:40:49 -07:00
Scott Lahteine	d36d4edd80	Tweak partial homing code	2016-06-18 01:16:50 -07:00
Scott Lahteine	d3a05de96e	Save and restore feedrate in probe functions	2016-06-18 01:16:26 -07:00
Juan Ricardo Gomez Anaya	5991eb428f	Update Spanish Language ... Spanish language update and also add missing messages	2016-06-18 00:27:04 -05:00
Scott Lahteine	f33bd0bb10	Merge pull request #4077 from thinkyhead/rc_delete_old_macros ... Delete some obsolete Z servo macros	2016-06-17 18:59:16 -07:00
Scott Lahteine	defcacc1a9	Delete some obsolete Z servo macros	2016-06-17 18:49:17 -07:00
Scott Lahteine	bbf5b486c3	Add an SD Card stop function, use in ultralcd	2016-06-17 18:27:14 -07:00
Scott Lahteine	3a150f07c2	Merge pull request #4073 from thinkyhead/rc_temp_mystery ... Minor tweaks to M109 / M190	2016-06-17 17:49:50 -07:00
Scott Lahteine	bd4ec727e7	Merge pull request #4066 from thinkyhead/rc_M851_with_probe ... Make M851 standard with a bed probe	2016-06-17 17:32:55 -07:00
Scott Lahteine	692a6e7c91	Merge pull request #4065 from thinkyhead/rc_goodbye_xy_servos ... Remove support for XY servo endstops	2016-06-17 17:32:08 -07:00
Scott Lahteine	de177ba6c9	Minor tweaks to M109 / M190	2016-06-17 17:26:21 -07:00
Scott Lahteine	eab44b30d4	Safety and serial sections	2016-06-17 15:19:43 -07:00
Scott Lahteine	fc56a547d1	Rename movement section to motion	2016-06-17 15:19:43 -07:00
Scott Lahteine	a8b8796cd7	Define probe offsets when a probe exists	2016-06-17 15:19:42 -07:00
Scott Lahteine	1000563d80	Make M851 standard with a bed probe	2016-06-17 15:19:42 -07:00
Scott Lahteine	f66a194159	Merge pull request #4062 from jbrazio/bugfix/compiler-warnings ... Fixes misc gcc warnings	2016-06-17 14:23:28 -07:00
Scott Lahteine	1bed392c68	HAS_Z_ENDSTOP_SERVO => HAS_Z_SERVO_ENDSTOP	2016-06-17 14:20:17 -07:00
Scott Lahteine	47ce810f52	Remove support for XY servo endstops	2016-06-17 14:19:17 -07:00
João Brázio	d1e5dc6319	Fixes misc gcc warnings	2016-06-17 20:24:24 +01:00
esenapaj	c5eecb11b2	Follow-up the PR #4055 (Croatian language support) ... ・Update a forgotten Configuration.h of Cartesio	2016-06-17 21:20:15 +09:00
Scott Lahteine	d991a4c24a	Merge pull request #4063 from thinkyhead/rc_remove_swp_files ... Delete mysterious .swp files from #3609	2016-06-16 17:22:48 -07:00
Scott Lahteine	8d8cbef1de	Merge pull request #4055 from thinkyhead/rc_croatian_language ... Croatian language support	2016-06-16 17:22:25 -07:00
Scott Lahteine	ebbed2975e	Delete mysterious .swp files from #3609	2016-06-16 16:42:03 -07:00
Scott Lahteine	02e5dad29a	Include Croatian in language listings	2016-06-16 16:18:26 -07:00
Scott Lahteine	2015aad867	Tweak Croatian language file heading	2016-06-16 16:09:57 -07:00
Robert Marko	884bc63fbe	Add Croatian language	2016-06-16 16:09:57 -07:00
Scott Lahteine	ef3bef6b9e	Fix feedrate in gcode_T (max_feedrate is mm/s)	2016-06-16 16:03:14 -07:00
Scott Lahteine	4640974e1b	Merge pull request #4060 from esenapaj/Follow-up-the-PR-#4053 ... Follow-up and improvement the PR #4053 (CNControls Cartesio UI Support)	2016-06-16 15:44:00 -07:00
esenapaj	106227540e	Follow-up and improvement the PR #4053 (CNControls Cartesio UI Support) ... ・Add implimantation of PR #3609 to configuration files of Cartesio ・Standardize macro names	2016-06-16 19:22:31 +09:00
MagoKimbra	008d0637dd	Fix gcode_T	2016-06-16 09:05:36 +02:00
edwilliams16	114d9db7d0	Show babysteps on the LCD in mm, not steps	2016-06-15 23:03:24 -07:00
Scott Lahteine	b410bf933b	Merge pull request #4053 from thinkyhead/rc_cartesio_redo ... CNControls Cartesio UI Support	2016-06-15 22:33:45 -07:00
Scott Lahteine	f639044c24	Merge pull request #3609 from jbrazio/feature/config-version ... Adds versioning for Configuration.h & Configuration_adv.h	2016-06-15 22:09:47 -07:00
Scott Lahteine	4d2cb70152	Cartesio UI Support	2016-06-15 21:46:54 -07:00
Scott Lahteine	da90bbe0eb	Merge pull request #4010 from thinkyhead/rc_toolchange_adjust ... Fixup position adjustment on toolchange	2016-06-15 21:10:33 -07:00
Scott Lahteine	948c467e16	Merge pull request #4043 from AnHardt/save_delay ... Introduce save_delay()	2016-06-15 21:06:43 -07:00
Scott Lahteine	4b93989a77	MBL Z adjustment on toolchange	2016-06-15 20:49:36 -07:00
Scott Lahteine	9c800d1f8c	Position adjustment for bed leveling	2016-06-15 20:49:36 -07:00
Scott Lahteine	8c7babb70f	Merge pull request #4049 from esenapaj/Fix-for-the-PR-#4023 ... Fix for the PR #4023(Add macros to move servos)	2016-06-15 20:39:46 -07:00
AnHardt	1219310622	Introduce save_delay() ... Introduce save_delay() for long delays what otherwise would cause watchdog resets Explizit lcd_set_custom_characters(false) at the end of bootscreen(). Else the charset is not proper set in case of LCD_PROGRESS_BAR.	2016-06-15 18:11:55 +02:00
esenapaj	44f091a413	Fix for the PR #4023(Add macros to move servos) ... ・Add missing ')'	2016-06-15 22:34:55 +09:00
Alexander Leisentritt	c2b7ef1e7e	"e" was renamed to "eindex" in a previous commit	2016-06-15 11:11:16 +02:00
Scott Lahteine	52ac2a62ee	Merge pull request #4013 from thinkyhead/rc_toolchange_no_move ... Use "Tn S1" to change tools without moving	2016-06-14 20:13:01 -07:00
Scott Lahteine	d2a00b74e3	Merge pull request #4004 from thinkyhead/rc_feedrate_in_gcode_T ... Use linear feedrate in gcode_T, not volumetric	2016-06-14 20:10:08 -07:00
Scott Lahteine	0ad26d0de8	Merge pull request #4034 from AnHardt/custom-splash-screen ... Custom Splash Screen	2016-06-14 18:51:39 -07:00
esenapaj	741cda0e47	Follow-up the PR #3676(Advance extrusion algorithm – LIN_ADVANCE) ... ・Update forgotten example configurations	2016-06-15 00:10:15 +09:00
AnHardt	02b3d6b8d3	Custom Splash Screen ... Custom Splash Screen for full graphic displays. Too complicated for the hitachis without knowing what exactly to display. On top of #4032 Realisation of an idea from #3996	2016-06-14 09:39:28 +02:00
Scott Lahteine	78a48d7e3c	Merge pull request #4038 from thinkyhead/rc_fix_heater_off ... Fix broken DISABLE_HEATER macro	2016-06-13 20:58:34 -07:00
Scott Lahteine	ee5be92206	Fix broken DISABLE_HEATER macro	2016-06-13 20:57:58 -07:00
Scott Lahteine	8d8180e028	Parse M905 args in Marlin_main.cpp	2016-06-13 19:25:28 -07:00
Scott Lahteine	2b340f5acb	patch LIN_ADVANCE to use code_value_float	2016-06-13 18:54:25 -07:00
Scott Lahteine	b708196770	Merge pull request #4032 from AnHardt/bootscreen-delay ... Show bootscreen later	2016-06-13 18:27:05 -07:00
Scott Lahteine	587de1b6b6	Merge pull request #3676 from thinkyhead/rc_lin_advance_feature ... Advance extrusion algorithm – LIN_ADVANCE	2016-06-13 18:04:58 -07:00
AnHardt	b4fedec0d1	Show bootscreen later ... Init display and show bootscreen later, but init display in `kill()` to init outputs before the bootscreen delays but being able to display kill errors.	2016-06-14 01:59:50 +02:00
Silvio Didonna	08e2c5a6ea	Added and translated some strings from language_en	2016-06-13 13:04:09 +02:00
Scott Lahteine	4d2119f83a	_lcd_move => _lcd_move_xyz	2016-06-12 17:14:19 -07:00
Scott Lahteine	811967923a	Fix manual_move to move the correct E stepper	2016-06-12 17:14:19 -07:00
Scott Lahteine	0d0b751498	Merge pull request #4023 from thinkyhead/rc_servo_macros ... Add macros to move servos	2016-06-12 15:45:39 -07:00
Scott Lahteine	4fbe818163	Add macros to move servos	2016-06-12 15:38:30 -07:00
Scott Lahteine	b322ac4417	No need to check ULTIPANEL with DOGLCD	2016-06-11 16:50:06 -07:00
João Brázio	8ccd97e7cc	Updated all example configuration files	2016-06-12 00:36:15 +01:00
Scott Lahteine	c7eeb09e8f	Merge pull request #4012 from Blue-Marlin/watchdoghealing ... Heal the watchdog	2016-06-11 16:18:22 -07:00
Scott Lahteine	7fb69e24fb	Use "Tn S1" to change tools without moving	2016-06-11 15:58:45 -07:00
Scott Lahteine	2f1bf8373b	Merge pull request #4005 from thinkyhead/rc_prepare_move_destination ... Clarify names of prepare_move functions	2016-06-11 15:51:58 -07:00
João Brázio	de8108648f	Added a versioning system to the config files	2016-06-11 23:48:10 +01:00
Blue-Marlin	efe719f898	Heal the watchgog	2016-06-12 00:34:31 +02:00
Scott Lahteine	b75e648f2c	Clarify names of prepare_move functions	2016-06-11 15:32:49 -07:00
Scott Lahteine	ae9b09fe94	menu => screen	2016-06-11 14:53:39 -07:00
Scott Lahteine	45ea8749d3	Wrap all items depending on ULTIPANEL	2016-06-11 14:27:34 -07:00
Scott Lahteine	0e2bfd0769	Use linear feedrate in gcode_T, not volumetric	2016-06-10 18:27:01 -07:00
Scott Lahteine	bf8710d522	Merge pull request #4001 from Blue-Marlin/manage_manual_move-ULTIPANEL ... manage_manual_move(); -> ULTIPANEL	2016-06-10 17:17:57 -07:00
João Brázio	2c34ec2bac	Closes #3999: Compilation error with BEEPER_PIN -1	2016-06-11 00:12:49 +01:00
Blue-Marlin	378ff92e98	manage_manual_move(); -> ULTIPANEL ... Makr the call of `manage_manual_move() ` depandent of `ULTIPANEL`	2016-06-10 23:36:57 +02:00
Scott Lahteine	aad9c0ed8d	Apply updated ISR timing code	2016-06-09 21:03:27 -07:00
Scott Lahteine	506d78b2f8	Run the advance_isr faster instead of doing multiple e-steps per interrupt	2016-06-09 21:03:27 -07:00
Scott Lahteine	6d62a4ffc8	Patch LIN_ADVANCE for style and forward-compatibility	2016-06-09 21:03:27 -07:00
Sebastianv650	fb8e880734	Add LIN_ADVANCE	2016-06-09 21:03:27 -07:00
Scott Lahteine	e2d4919c01	Merge pull request #3991 from thinkyhead/rc_axis_units ... Rename some vars to clarify their relationship to acceleration	2016-06-09 20:57:01 -07:00
Scott Lahteine	74060f17b7	Merge pull request #3995 from thinkyhead/rc_nonblocking_buzzer ... New feature: Non blocking tone queue	2016-06-09 20:55:29 -07:00
Scott Lahteine	a82c755a35	Fix BQ_LCD_SMART_CONTROLLER pin compiler warnings	2016-06-09 20:38:23 -07:00
João Brázio	5b5aa1572b	Non-blocking buzzer	2016-06-09 20:20:05 -07:00
Scott Lahteine	72c6f2923f	axis_steps_per_unit => axis_steps_per_mm	2016-06-09 17:04:51 -07:00
Scott Lahteine	446515ab79	Adjust spacing in block_t	2016-06-09 17:04:51 -07:00
Scott Lahteine	80ab749563	Rename acceleration locals for clarity	2016-06-09 17:04:51 -07:00
Scott Lahteine	3b08eb1eeb	acceleration_st => acceleration_steps_per_s2	2016-06-09 17:04:51 -07:00
Scott Lahteine	cb4704e07a	Rename some planner acceleration vars ... - `per_sq_second` => `per_s2` - `per_sqr_second` => `per_s2` - `axis_steps_per_sqr_second` => `max_acceleration_steps_per_s2`	2016-06-09 17:04:50 -07:00
Scott Lahteine	3c68be79dc	Throw an error in PID_autotune for E < -1	2016-06-09 16:41:53 -07:00
Scott Lahteine	26f8f54c56	Merge pull request #3985 from thinkyhead/rc_inch_fahrenheit_kelvin ... Support inches, fahrenheit, and kelvin	2016-06-08 20:10:33 -07:00
Scott Lahteine	f0a5b7f0bc	Merge pull request #3986 from thinkyhead/rc_mbl_forward_iteration ... Use memset in mbl.reset to save 58 bytes	2016-06-08 17:33:41 -07:00
Scott Lahteine	0b3142b45b	Remove redundant declarations from M100 code	2016-06-08 17:09:34 -07:00
Scott Lahteine	4980ecc1f7	Smaller binary using inline gcode argument getters	2016-06-08 17:03:28 -07:00
Reid Rankin	16212432c9	G20/21 and M149 support, and code_value() refactor ... This is an update of MarlinDev PR #196. G20/21: support for switching input units between millimeters and inches. M149: support for changing input temperature units. In support of these changes, code_value() and code_value_short() are replaced with an array of functions which handle converting to the proper types and/or units.	2016-06-08 16:51:10 -07:00
Scott Lahteine	a569e89775	Merge pull request #3978 from thinkyhead/rc_planner_local_rename ... Rename some auto/locals to avoid name conflict	2016-06-08 16:41:57 -07:00
Scott Lahteine	2d55862499	Use memset in mbl.reset to save 58 bytes	2016-06-08 16:05:18 -07:00
Scott Lahteine	b23f710034	Cleanup and naming for num-to-string functions	2016-06-08 13:12:27 -07:00
Scott Lahteine	3d56b9d127	Merge pull request #3979 from thinkyhead/mbl_cell ... MBL: cel => cell	2016-06-07 19:12:46 -07:00
Scott Lahteine	cca047424d	MBL: cel => cell	2016-06-07 19:10:39 -07:00
Scott Lahteine	49ecaf774d	Rename some auto/locals to avoid name conflict	2016-06-07 15:38:45 -07:00
petrzjunior	9171a3d94f	Update Czech language 2016/06/07	2016-06-07 19:25:15 +02:00
Scott Lahteine	5e6fdbb4cb	Merge pull request #3963 from thinkyhead/rc_advance_steppers ... Use e_steps[EXTRUDERS] instead of e_steps[4]	2016-06-05 02:46:06 -07:00
Scott Lahteine	47b5c55c29	Implement the delayed-move technique	2016-06-05 02:29:49 -07:00
Scott Lahteine	a3e25a0fca	Instead of trying to move now, set a flag to move asap	2016-06-05 02:29:48 -07:00
Scott Lahteine	e2a8961635	Use e_steps[EXTRUDERS] instead of e_steps[4]	2016-06-05 01:44:53 -07:00
Scott Lahteine	43947072d5	Merge pull request #3895 from thinkyhead/rc_singlenozzle_part_2 ... SINGLENOZZLE: EXTRUDERS versus HOTENDS	2016-06-04 15:23:17 -07:00
Scott Lahteine	d7e4e8e9be	Fix a typo in #3955	2016-06-04 02:09:58 -07:00
Scott Lahteine	c2362c1b3c	Apply Marlin coding standards to MBL class	2016-06-03 21:43:32 -07:00
Edward Patel	c06de0f097	MBL: Added keeping MBL active when homing single axises for #3750	2016-06-03 21:42:29 -07:00
Scott Lahteine	f2fb66c00d	With SINGLENOZZLE only set temperature for the active tool	2016-06-03 17:38:03 -07:00
Scott Lahteine	cd441ce652	SINGLENOZZLE: EXTRUDERS versus HOTENDS	2016-06-03 17:38:03 -07:00
Scott Lahteine	32f8300cc6	Merge pull request #3944 from thinkyhead/rc_eboston_lcd_contrast ... Improved LCD contrast handling	2016-06-03 17:08:41 -07:00
Scott Lahteine	9c87bf835c	Merge pull request #3947 from thinkyhead/rc_statics_stepper ... Apply static to remaining Stepper methods	2016-06-03 17:08:15 -07:00
Scott Lahteine	08871d4d6e	Merge pull request #3950 from boelle/patch-3 ... last of missing defines added	2016-06-03 17:07:02 -07:00
Scott Lahteine	4e13cd3f35	Merge pull request #3955 from MagoKimbra/RCBugFix ... Fix M428 width DELTA & SCARA	2016-06-03 15:50:37 -07:00
Scott Lahteine	2403a1cf9c	Merge pull request #3952 from rafacouto/RCBugFix ... Galician language update.	2016-06-03 15:46:03 -07:00
Scott Lahteine	8529122af1	Merge pull request #3946 from thinkyhead/rc_g28_servo_raise_before_stow ... Raise the servo probe before stow outside ABL context	2016-06-03 15:45:36 -07:00
MagoKimbra	f499be084a	Fix M428 width DELTA & SCARA	2016-06-03 23:23:23 +02:00
Rafa Couto	5f8db3f574	Galician language update.	2016-06-03 18:24:53 +02:00
Bo Herrmannsen	8532bf4087	last of missing defines added ... need to check line 101-103	2016-06-03 11:20:46 +02:00
Scott Lahteine	81384dfd36	Apply static to remaining stepper methods	2016-06-02 18:00:31 -07:00
Scott Lahteine	664b299a51	This fix is not DELTA compatible	2016-06-02 17:16:19 -07:00
Scott Lahteine	064efb20e0	Also call clear_command_queue for lcd_sdcard_stop	2016-06-02 17:16:19 -07:00
Scott Lahteine	6277395e1e	set_current_position_from_planner() after stepper.quick_stop()	2016-06-02 17:16:19 -07:00
Scott Lahteine	381bc6f0b0	set_position => set_position_mm	2016-06-02 17:16:19 -07:00
Scott Lahteine	663d2463dc	Merge pull request #3922 from thinkyhead/rc_statics_stepper ... Apply static to Stepper class	2016-06-02 17:14:24 -07:00
Scott Lahteine	194185539d	Merge pull request #3925 from thinkyhead/rc_statics_planner ... Apply static to Planner class	2016-06-02 17:14:04 -07:00
Scott Lahteine	3fd9b331f0	Merge pull request #3924 from thinkyhead/rc_statics_temperature ... Apply static to Temperature class	2016-06-02 17:13:17 -07:00
Scott Lahteine	db0fd021d0	Z raise options independent of ABL so G28 can use them	2016-06-02 16:56:49 -07:00
Scott Lahteine	9eecb4404b	Make raise_z_after_probing null sometimes	2016-06-02 16:56:49 -07:00
Scott Lahteine	28fb1f8994	Tweak #endif comment for ABL GRID	2016-06-02 16:56:49 -07:00
Scott Lahteine	b3a37b493d	Patch G28 servo stow to use Conditionals, raise_z_after_probing	2016-06-02 16:56:49 -07:00
Scott Lahteine	5390c846a5	Positive conditions for HAS_LCD_CONTRAST	2016-06-02 16:17:34 -07:00
Scott Lahteine	efa7209acf	Improved LCD contrast handling ... Based on MarlinFirmware/MarlinDev#200 from @eboston	2016-06-02 16:17:34 -07:00
Scott Lahteine	b703fa9538	Add sanity check for SAV_3DGLCD display types	2016-06-02 15:21:17 -07:00
lrpirlet	3aefa04386	Raise the servo probe before stow outside ABL context	2016-06-01 21:53:45 +02:00
Scott Lahteine	9729e9c450	Combine ST7565 / U8GLIB_NHD_C12864 items in dogm	2016-06-01 01:42:14 -07:00
Scott Lahteine	f331763eca	Merge pull request #3829 from thinkyhead/rc_fix_T_command ... Fix bad movement in gcode_T when switching extruders	2016-05-31 19:36:18 -07:00
Scott Lahteine	67f816ff79	Merge pull request #3926 from thinkyhead/rc_statics_endstops ... Drop FORCE_INLINE from endstops.h	2016-05-31 19:35:41 -07:00
Scott Lahteine	2bd4f33369	Merge pull request #3928 from thinkyhead/rc_allen_key_cleanup ... Remove excess allen key probe examples from configs	2016-05-31 19:18:21 -07:00
Scott Lahteine	d698c89971	Fix bad movement in gcode_T when switching	2016-05-31 19:14:33 -07:00
Scott Lahteine	1a01a44a94	Merge pull request #3936 from thinkyhead/rc_sav_mk1 ... Support for SAV_3DGLCD OLED LCD controller	2016-05-31 18:46:25 -07:00
Scott Lahteine	4770d7c346	Merge pull request #3933 from boelle/patch-2 ... added defines present in en but not in da	2016-05-31 18:42:38 -07:00
Scott Lahteine	c6c01eaaac	Merge pull request #3888 from thinkyhead/rc_slower_max31855 ... Slower SPI speed for MAX31855	2016-05-31 18:40:38 -07:00
Scott Lahteine	a0b000d752	Support for SAV_3DGLCD OLED LCD controller	2016-05-31 14:41:16 -07:00
Scott Lahteine	bd97bbc52a	Make HAS_LCD_CONTRAST a boolean flag	2016-05-31 11:47:02 -07:00
Scott Lahteine	bc77670673	Merge pull request #3929 from thinkyhead/rc_fix_printrboard_dac ... Need to call dac_init() in setup() for DAC_STEPPER_CURRENT	2016-05-31 10:29:37 -07:00
Bo Herrmannsen	a1a8240606	added defines present in en but not in da	2016-05-31 14:57:52 +02:00
Bo Herrmannsen	5eb7a79d93	initial changes to DA	2016-05-31 14:24:33 +02:00
Scott Lahteine	55ef04a566	Need to call dac_init() in setup() for DAC_STEPPER_CURRENT ... As reported by https://github.com/MarlinFirmware/Marlin/pull/3182#issuecomment-222595488	2016-05-30 23:35:06 -07:00
Scott Lahteine	43a71ef226	Remove excess allen key probe examples from configs	2016-05-30 18:26:53 -07:00
Scott Lahteine	1582ed43bf	Merge pull request #3918 from epatel/marlin/mbl_negative_xy_adv ... MBL: Move border macros to Configuration_adv.h	2016-05-30 18:15:50 -07:00
Scott Lahteine	ff53819856	Drop FORCE_INLINE in planner.h ... This change actually does increase the binary size by about 12 bytes, but how does it affect performance?	2016-05-30 17:18:28 -07:00
Scott Lahteine	e60224a943	Drop FORCE_INLINE from endstops.h ... `FORCE_INLINE` seems to have no effect with standard optimization.	2016-05-30 17:08:56 -07:00
Scott Lahteine	85512e9372	Drop FORCE_INLINE from temperature.h ... `FORCE_INLINE` seems to have no effect on code generation with standard optimization.	2016-05-30 17:06:50 -07:00
Scott Lahteine	78fb02a5ad	Apply static to Temperature class	2016-05-30 16:50:51 -07:00
Scott Lahteine	c3df293fc6	Merge pull request #3923 from thinkyhead/rc_statics_endstops ... Apply static to Endstops class	2016-05-30 16:48:23 -07:00
Scott Lahteine	02735fd500	Merge pull request #3921 from thinkyhead/rc_calc_timer_tweak ... Tiny calc_timer speedup	2016-05-30 16:47:03 -07:00
Scott Lahteine	668d50f68e	Keep Stepper encapsulation, use static data and methods	2016-05-30 16:24:04 -07:00
Scott Lahteine	26f866b908	Apply static to Endstops class	2016-05-30 16:23:43 -07:00
Scott Lahteine	470d5ac09f	Apply static to Planner class	2016-05-30 16:22:41 -07:00
Scott Lahteine	ecfdcf7250	Tiny calc_timer speedup	2016-05-30 16:17:02 -07:00
Edward Patel	06593833ff	MBL: Move border macros to Configuration_adv.h	2016-05-30 20:50:16 +02:00
Scott Lahteine	ffe55c230d	Merge pull request #3914 from thinkyhead/rc_fix_lcd_contrast ... Patch conditionals for DEFAULT_LCD_CONTRAST, MINIPANEL	2016-05-30 11:20:14 -07:00
Scott Lahteine	d3efc96289	Patch conditionals for DEFAULT_LCD_CONTRAST, MINIPANEL ... - `DEFAULT_LCD_CONTRAST` was incorrectly overriding all `DOGLCD` - `MINIPANEL` conditionals are identical to `MAKRPANEL`	2016-05-30 01:10:47 -07:00
Edward Patel	92a27c37b3	MBL: Apply https://github.com/MarlinFirmware/Marlin/pull/3903 to example_configurations	2016-05-30 09:50:11 +02:00
Scott Lahteine	3861f1e0da	Merge pull request #3908 from jbrazio/bugfix/3826 ... Closes #3826: SD printing will now pause and stop the print counter	2016-05-30 00:08:57 -07:00
Scott Lahteine	8806c7bbcc	Merge pull request #3903 from epatel/marlin/mbl_negative_xy ... MBL: Fix for negative x/y positions	2016-05-29 22:07:35 -07:00
Scott Lahteine	dc22097b3a	Fix some of array initializations ... - In `stepper.h` init `count_direction` array - In `ultralcd.cpp` init `autotune_temp` array	2016-05-29 20:55:13 -07:00
João Brázio	40e64b36de	Closes #3826: SD printing will now pause and stop the print counter ... The LCD menu items for SD printing pause/stop have been updated to control also the print job timer. This commit also fixes a small output bug with M78, the failed print counter was displaying the wrong value.	2016-05-30 00:56:39 +01:00
Edward Patel	eb2746a34f	MBL: Fix for negative x/y positions	2016-05-28 21:05:43 +02:00
Scott Lahteine	fe3122774a	Merge pull request #3806 from thinkyhead/rc_coreyz_support ... Support for COREYZ. Fixes for COREXY, COREXZ	2016-05-26 18:50:43 -07:00
Scott Lahteine	fad7680605	Slower SPI speed for MAX31855	2016-05-25 18:15:36 -07:00
Scott Lahteine	30f6b84561	Merge pull request #3812 from thinkyhead/rc_mbl_index_finders ... Two index finding functions for MBL	2016-05-23 15:54:37 -07:00
Scott Lahteine	89e630b2fb	Merge pull request #3808 from thinkyhead/rc_singlenozzle ... SINGLENOZZLE	2016-05-23 15:52:19 -07:00
Scott Lahteine	827738a790	set_z parameters marked const	2016-05-23 14:25:43 -07:00
Scott Lahteine	9049f4084b	EEPROM report uses G29 S3	2016-05-23 14:25:43 -07:00
Scott Lahteine	4955163959	Propose simpler probe index methods	2016-05-23 14:25:43 -07:00
Scott Lahteine	a1a5cb5393	Propose simpler cel index methods	2016-05-23 14:25:42 -07:00
Scott Lahteine	360adc6a3b	Small reduction in M421 code	2016-05-23 14:25:42 -07:00
Scott Lahteine	a4ed988c60	Two index finding functions for MBL	2016-05-23 14:25:42 -07:00
Scott Lahteine	0e55c06f7d	Rename CORE_AXIS_3 to NORMAL_AXIS	2016-05-23 13:58:40 -07:00
Scott Lahteine	5172d4ba40	COREYZ stepper, planner, endstop, babysteps	2016-05-23 13:58:40 -07:00
Scott Lahteine	6c7f4909b1	COREYZ Conditionals, SanityCheck for only a single kinematic	2016-05-23 13:58:40 -07:00
Scott Lahteine	95fee8ca81	Add option for CoreYZ kinematics	2016-05-23 13:58:40 -07:00
Scott Lahteine	678cbad76a	Merge pull request #3819 from jbrazio/bugfix/followup-3813 ... Followup for #3813	2016-05-23 13:56:11 -07:00
AnHardt	bb66ffb2ae	Correct hardware endstops default ... All credits to RicardoGA	2016-05-23 10:54:22 +02:00
João Brázio	75221fa673	Followup for #3813	2016-05-22 13:14:58 +01:00
Scott Lahteine	f9b4b90058	Merge pull request #3813 from jbrazio/bugfix/3809 ... Stopwatch and PrintCounter improvements	2016-05-21 18:33:57 -07:00
João Brázio	8c0edb2de4	Fixes #3809 and adds several improvements to the Stopwatch and ... PrintCounter classes	2016-05-22 01:59:59 +01:00
Scott Lahteine	c5130fd23b	Additional instructions for controller reverse options	2016-05-20 18:14:50 -07:00
Scott Lahteine	cadf441059	Merge pull request #3798 from AnHardt/extend-M421 ... Extend M421 with I and J parameters	2016-05-20 16:17:23 -07:00
Scott Lahteine	0c7c45063b	PID_ADD_EXTRUSION_RATE based on MarlinKimbra	2016-05-20 16:15:05 -07:00
Scott Lahteine	92ac133f2b	Conditionals and Sanity Check for SINGLENOZZLE	2016-05-20 15:48:27 -07:00
Scott Lahteine	69abfef82e	Add "SINGLENOZZLE" extruder option	2016-05-20 15:45:11 -07:00
AnHardt	f5a036510f	Extend M421 with I and J parameters ... Extend M421 with I and J parameters	2016-05-21 00:18:09 +02:00
Scott Lahteine	2f6e7b7b9b	Merge pull request #3805 from MatixYo/patch-7 ... Update language_pl.h to the latest strings	2016-05-20 14:50:49 -07:00
Scott Lahteine	1a6c72cb57	Apply to the rest of the configs	2016-05-20 11:52:27 -07:00
Scott Lahteine	37c6d0f4ed	Reword MESH_G28_REST_ORIGIN comment	2016-05-20 11:52:27 -07:00
Edward Patel	c7d90dc5ec	Add option to configure G28 all axis resting position for MBL	2016-05-20 11:52:27 -07:00
Mateusz Juszczyk	bbe4c20ef6	Update language_pl.h	2016-05-20 13:24:34 +02:00
Scott Lahteine	319d184999	Merge pull request #3803 from jbrazio/feature/buildroot-cleanup ... Buildroot cleanup	2016-05-19 21:34:11 -07:00
Scott Lahteine	a469341555	Merge pull request #3800 from jbrazio/feature/move-felix-cfg ... Moves Felix's dual configuration to a folder	2016-05-19 18:53:39 -07:00
João Brázio	14652bb141	Moves shared helper scripts to the buildroot	2016-05-20 02:25:13 +01:00
João Brázio	80f05920c5	Moves Felix's dual configuration to a folder	2016-05-20 00:49:16 +01:00
Scott Lahteine	8218558953	Update comments, rename next_ping_ms, followup to #3797	2016-05-19 16:44:57 -07:00
Scott Lahteine	6d68b12e28	Merge pull request #3797 from AnHardt/fix-screen-updatedelay ... Rework intermediate idle() and manage_heater() calls in G2/G3 and G5	2016-05-19 16:29:27 -07:00
AnHardt	e761bdbb4b	Remove SF_ARC_FIX from G5 (Cubic B-spline) ... Remove SF_ARC_FIX from G5 (Cubic B-spline). SF_ARC_FIX is a fix for G2/G3 (arcs) where Skeinforge always produced relative instead of absolute coordinates for the endpoint of an arc. It's very unlikely this is also a problem with Cubic B-splines. More likely is copying from the G2/G3 code.	2016-05-19 21:00:12 +02:00
AnHardt	2207001333	No compromises for the manage_heater() ... No compromises for the manage_heater(). manage_heater() will return immediately when there is nothing to do, but needs a constant detaT to work proper. Calling idle() only every 200ms results in a display update every ~2 seconds - that should be enough. For the other functionalities in idle() and manage_inactivity() 200ms is a lot but hopefully works.	2016-05-19 20:52:11 +02:00
AnHardt	0c4d885d5b	Speedup sreen update delay ... Speedup sreen update delay and correct a comment. A module division by 10 is slooooow. (powers of 2 are fast - but then you can AND a bitmask with the same result)	2016-05-19 15:41:09 +02:00
Rafa Couto	9d416289cc	Update Galician language to 1.1.0-RCBugFix.	2016-05-19 19:33:40 +09:00
Scott Lahteine	07c9a11c3c	Automatically set X2 stepper pins	2016-05-18 19:09:09 -07:00
Scott Lahteine	8aa591ca09	Merge pull request #3789 from jbrazio/feature/m999-s-arg ... Implements S1 argument in M999	2016-05-18 16:58:09 -07:00
Scott Lahteine	138c5c8378	Merge pull request #3788 from thinkyhead/rc_dual_x_compile_fix ... DUAL_X_CARRIAGE fixes, improvements, Travis test	2016-05-18 16:56:54 -07:00
João Brázio	e6effb8f35	Implements S1 argument in M999	2016-05-19 00:13:33 +01:00
Scott Lahteine	2a7b1a85f7	Improve DUAL_X_CARRIAGE sanity check errors	2016-05-18 15:59:28 -07:00
Scott Lahteine	516e79bbda	Declare extruder_duplication_enabled in Marlin.h	2016-05-18 15:51:44 -07:00
esenapaj	56d5ae596c	Update Japanese trasration ... ・Add new translation ・Change translation	2016-05-18 20:42:50 +09:00
Scott Lahteine	4041508ffb	Function decl. in headers don't need "extern"	2016-05-17 18:35:01 -07:00
Scott Lahteine	82c2d308dc	Merge pull request #3783 from thinkyhead/rc_bezier_delta_fix ... Bezier style and DELTA patch	2016-05-17 18:27:48 -07:00
Scott Lahteine	ecec5c5e58	Bezier style and DELTA patch	2016-05-17 18:06:10 -07:00
Scott Lahteine	d66e53c42b	Merge pull request #3782 from thinkyhead/rc_home_z_before_g29 ... Require homing of Z before G29	2016-05-17 17:53:56 -07:00
Scott Lahteine	552516ddf5	Merge pull request #3781 from AnHardt/minor-delta-segmenting-speedup ... Minor DELTA segmentation speedup	2016-05-17 17:17:38 -07:00
Scott Lahteine	a28970784c	XYZ unhomed	2016-05-17 17:02:53 -07:00
Scott Lahteine	a9926b71a4	Require homing of Z before G29	2016-05-17 16:57:12 -07:00
AnHardt	41e9569dbc	Minor DELTA segmentation speedup ... Minor DELTA segmentation speedup by pulling calculations out of the loop.	2016-05-18 01:49:30 +02:00
Scott Lahteine	3016dfe484	Merge pull request #3744 from thinkyhead/rc_bezier_curves ... Add BEZIER_CURVE_SUPPORT — G5 command	2016-05-17 13:57:38 -07:00
Scott Lahteine	d0ac4541d3	Merge pull request #3775 from jbrazio/bugfix/followup-3770 ... G29: Report final position back to host when using MBL	2016-05-17 13:55:26 -07:00
João Brázio	b6a3aef297	G29: Report final position back to host when using MBL	2016-05-17 01:27:59 +01:00
esenapaj	95f30529a6	Add stowing process for MECHANICAL_PROBE	2016-05-16 18:12:10 +09:00
esenapaj	e2b87f6c85	Separate Z_PROBE_ALLEN_KEY from MECHANICAL_PROBE	2016-05-16 18:12:10 +09:00
Scott Lahteine	58339aea5f	Merge pull request #3769 from jbrazio/bugfix/iteration-invokes-undef-behavior ... Bugfix: iteration invokes undefined behavior	2016-05-15 20:36:25 -07:00
Scott Lahteine	26b4cb5b42	Merge pull request #3771 from thinkyhead/rc_auto_fans_again ... Fix checkExtruderAutoFans	2016-05-15 20:32:31 -07:00
Scott Lahteine	c9271e610b	Merge pull request #3762 from jbrazio/bugfix/lcd-hide-bed-icon ... Remove the hotbed icon from the status screen	2016-05-15 19:11:05 -07:00
Scott Lahteine	2f14934c65	Fix checkExtruderAutoFans ... Make sure to only set the fan state once when extruders share a fan	2016-05-15 18:54:37 -07:00
João Brázio	ecd490ed49	Bugfix: iteration invokes undefined behavior	2016-05-15 22:45:08 +01:00
Scott Lahteine	abdfd914f8	Merge pull request #3763 from esenapaj/patch-4 ... Follow-up for #3720 and #3759	2016-05-15 12:37:51 -07:00
Scott Lahteine	754b0152f5	Fix MBL zigzag calls	2016-05-15 12:35:01 -07:00
esenapaj	6d722716f7	Follow-up the PR #3720 and #3759 ... Update forgotten Configuration_DUAL.h	2016-05-15 14:08:45 +09:00
João Brázio	451000387d	Remove the hotbed icon when HAS_TEMP_BED is false	2016-05-15 03:00:05 +01:00
Scott Lahteine	a058226799	Prevent watchdog timeout in bezier moves	2016-05-14 17:41:16 -07:00
Scott Lahteine	13175ce7da	Fix error checking in M421	2016-05-14 17:12:44 -07:00
Scott Lahteine	bc5a547d55	More robust MBL index / point conversion	2016-05-14 16:45:56 -07:00
Scott Lahteine	a3520b6f01	More precision in M503 output for MBL's M421	2016-05-14 16:19:37 -07:00
Scott Lahteine	1b90682617	Merge pull request #3702 from thinkyhead/rc_sensitive_fan_pins ... Remove need to define unused pins as -1 in pins files	2016-05-14 15:49:22 -07:00
Scott Lahteine	c8a40f06a6	Merge pull request #3759 from thinkyhead/rc_more_printcounter ... Printcounter bugfix and some new features	2016-05-14 15:36:31 -07:00
Scott Lahteine	585c8a918f	Merge pull request #3758 from thinkyhead/rc_verbiage ... Tweaks to some verbiage	2016-05-14 15:27:11 -07:00
João Brázio	f9a62f6a8e	Added PRINTJOB_TIMER_AUTOSTART section to example config files	2016-05-14 15:22:45 -07:00
João Brázio	8a18c52002	Adds an option to disable print job timer auto start	2016-05-14 15:22:44 -07:00
João Brázio	a79267217b	M78 now allows stats reset using the S78 argument	2016-05-14 15:22:44 -07:00
João Brázio	b660f1bdb8	Bugfix: Multiple M77 no longer increment the print counter	2016-05-14 15:22:43 -07:00
Scott Lahteine	c63f95f2fe	Merge pull request #3748 from clexpert/patch-1 ... Lastest changes in Czech translate	2016-05-14 15:12:39 -07:00
Scott Lahteine	e01e52969e	Merge pull request #3757 from thinkyhead/rc_fix_auto_fans ... Don't try to enable unused auto fans	2016-05-14 15:09:24 -07:00
Scott Lahteine	ddf3e1e22d	Tweaks to some verbiage	2016-05-14 15:06:09 -07:00
Scott Lahteine	a713043acd	Merge pull request #3749 from esenapaj/patch-3 ... Enclose all #error strings by double-quotes	2016-05-14 15:01:56 -07:00
Scott Lahteine	3cfea3ff12	Merge pull request #3752 from AnHardt/fix-FIX_MOUNTED_PROBE ... G29 missing FIX_MOUNTED_PROBE condition	2016-05-14 15:00:42 -07:00
Scott Lahteine	08dfe08f9a	Merge pull request #3754 from jbrazio/feature/update-pt_PT ... Updated pt_PT language pack	2016-05-14 15:00:12 -07:00
Scott Lahteine	596ebccd54	Merge pull request #3753 from jbrazio/feature/followup-3740 ... Warn user about useless of individual axis homing and DELTA kinematics	2016-05-14 14:59:49 -07:00
Scott Lahteine	6e3556cb75	Merge pull request #3746 from esenapaj/patch-2 ... Update Japanese translation	2016-05-14 14:57:43 -07:00
Scott Lahteine	ddac17a195	Add BEZIER_CURVE_SUPPORT (G5 XYZEFIJPQ)	2016-05-14 14:52:08 -07:00
Scott Lahteine	b4c891dfd2	Remove obsolete reference to prepare_arc_move	2016-05-14 14:51:09 -07:00
Scott Lahteine	9f6b8f7d5b	Remove extra @section directive from configs	2016-05-14 14:51:09 -07:00
Scott Lahteine	4d6bb52b26	Don't try to enable unused auto fans ... Addressing #3743	2016-05-14 14:46:14 -07:00
Scott Lahteine	f13c4a9ec4	Merge pull request #3720 from jbrazio/feature/host-keepalive ... Removes the DISABLE from HOST_KEEPALIVE	2016-05-14 14:39:31 -07:00
João Brázio	596f15348d	Updated pt_PT language pack	2016-05-14 01:45:15 +01:00
João Brázio	d7522152e1	Warn user about useless of individual axis homing and DELTA kinematics	2016-05-14 01:35:05 +01:00
AnHardt	8a4376d51f	Idle during long arcs ... Idle during long arcs to prevent from watchdog resets during high segmented fast arcs.	2016-05-14 00:29:13 +02:00
esenapaj	888443ca1e	Enclose all #error strings with apostrophes	2016-05-13 21:10:23 +09:00
Petr Zahradnik	50b1a6bb2b	Lastest changes in Czech translate	2016-05-13 13:51:13 +02:00
AnHardt	b74af78736	Make arc support (G2/G3) configurable ... Saves about 2669 bytes when deactivated. (About 1% for a AT2560, about __4%__ for a AT644!)	2016-05-13 13:27:45 +02:00
AnHardt	aef2559bd8	fix-FIX_MOUNTED_PROBE ... Add a forgotten condition	2016-05-13 12:07:17 +02:00
esenapaj	e9d851137d	Update Japanese translation ... ・Add new translation	2016-05-13 18:52:35 +09:00
Scott Lahteine	14cd0f4c92	Merge pull request #3740 from thinkyhead/rc_lcd_home_options ... Individual Axis Homing LCD menu items	2016-05-12 11:59:46 -07:00
esenapaj	69511b5e5e	Follow-up the PR #3719(Harmonize LCD comment section) ... It update forgotten Configuration_DUAL.h.	2016-05-12 19:16:36 +09:00
Scott Lahteine	675e92ab1f	Merge pull request #3738 from thinkyhead/rc_limit_i2c_request ... Print an error on bad i2c request	2016-05-11 19:36:49 -07:00
João Brázio	09150cae79	Individual Axis Homing LCD menu items	2016-05-11 19:28:19 -07:00
Scott Lahteine	4dc4e2063f	Add REVERSE_ENCODER_DIRECTION option	2016-05-11 15:39:28 -07:00