Commit Graph

11662 Commits

Author SHA1 Message Date
Scott Lahteine
7ee5894360 Allow float XY probe offsets
Responding to #12383

XY probe offsets should be integers because adding decimal points makes the code larger. But if decimals are very much wanted, this commit removes the old restriction.
2018-11-17 07:44:47 -06:00
Giuliano Zaro
43ecdb606f Fix a compile warning (#12452) 2018-11-17 07:08:25 -06:00
Ph0non
984c4ba8c7 Enable SD Card on RepRap Display and RADDS (#12446)
* Enable SD Card on RepRap Display and RADDS

Define the necessary pins in `pins_RADDS.h` (copied from the `RADDS_DISPLAY` section) for the use of the SD card slot on RRD.
2018-11-17 06:59:40 -06:00
Ludy
56a94c2a26 Use 'target_extruder' in M104 as with M109 (#12448) 2018-11-17 06:55:25 -06:00
Scott Lahteine
66580f32c2
Make CardReader class static (#12451)
* Make CardReader a static class
* Make CardReader flags into bitfields
2018-11-16 22:39:16 -06:00
Scott Lahteine
3e9ffaddb6
Consolidate, optimize some LCD menu code (#12450) 2018-11-16 21:44:48 -06:00
Scott Lahteine
d97e31db4c
Optimize Power-Loss Recovery (#12440) 2018-11-16 20:47:07 -06:00
Mateusz Krawczuk
ca21ac6b9b Support two MAX6675 thermocouples (#8686) 2018-11-16 18:20:33 -06:00
Scott Lahteine
0e610815e4 No need for Cap:PAREN_COMMENTS 2018-11-16 04:28:40 -06:00
Scott Lahteine
7a075a5dc9 Tweak extruder errors 2018-11-16 01:32:21 -06:00
Scott Lahteine
2d92f333f5 Fix GcodeSuite::T active_extruder reference 2018-11-15 14:07:24 -06:00
Scott Lahteine
d2bb53702a
Optimize target_extruder, ignore T with mixing (#12432)
* Optimize target_extruder, ignore T with mixing
* Give G-code Tn parity with tool_change
2018-11-14 17:33:04 -06:00
Marcio Teixeira
5e586a6b39 Fix to runout sensor code. (#12431)
- "old_state" is no longer a class static variable.
2018-11-14 16:54:05 -06:00
Scott Lahteine
d82c350de7
Miscellaneous LCD code renaming, reordering (#12430)
* Move special characters to language.h
* Apply some naming standards
* Clean up menu item draw functions
* Rename some Temperature methods
* UI => ExtUI
2018-11-14 13:13:51 -06:00
Scott Lahteine
edfd106bc5
Rejigger Filament Runout class (#12428) 2018-11-14 11:45:57 -06:00
Scott Lahteine
f4c128ecaa
Move RRW keypad code to a common method (#12429) 2018-11-14 06:00:21 -06:00
Scott Lahteine
54ec5528a0 hasstatus => has_status 2018-11-14 01:34:28 -06:00
Scott Lahteine
ebf585b673 Fix an old sanity check 2018-11-14 01:15:35 -06:00
Ryan
052d102ded UltiMachine Archim 1 support (#12404) 2018-11-14 00:27:39 -06:00
Scott Lahteine
664e20754d Clean up pins files 2018-11-14 00:23:33 -06:00
Scott Lahteine
1eb5249598 Fix Formbot Trex-2+ configs
Followup to #12422
2018-11-13 21:53:54 -06:00
thiagodesacosta
075a22ed65 Update Portuguese-Brazilian translation (#12402) 2018-11-13 19:42:25 -06:00
Marcio Teixeira
3ceab8474c Add required "cardreader.h" include (#12419) 2018-11-13 17:12:44 -06:00
Giuliano Zaro
98c2fc4e42 Endstops fix followup (#12423)
Followup to #12413
2018-11-13 17:10:07 -06:00
Roxy-3D
f19fd642ce
Updates to Formbot T-Rex 2+ configuration files (#12422)
Updates to Formbot T-Rex 2+ configuration files
2018-11-13 13:48:35 -06:00
Roxy-3D
cda5ef08fa
Debug of G2-G3 for UBL (#12386)
Changes only affect UBL.  Everything else is left alone.
2018-11-13 11:20:21 -06:00
AnHardt
9ad3aed0ef Fix tool-change for MIXING_EXTRUDER with < 2 virtual tools (#12417)
Fix #12416

Better handling of `ENABLED(MIXING_EXTRUDER) && !MIXING_VIRTUAL_TOOLS > 1` -  to not fall through to the general case. Fix compiler warnings for `#elif EXTRUDERS < 2`.
2018-11-13 04:56:10 -06:00
Giuliano Zaro
d631267548 Refine endstops fixes (#12413)
When endstops/probe are enabled `ENDSTOP_NOISE_THRESHOLD` calls to `update` are required to properly re-sync endstops/probe status.
2018-11-13 04:31:58 -06:00
Scott Lahteine
0ee1a92971
Group status methods, share reset_status with Extensible UI (#12414)
* Group status methods, share reset_status with Extensible UI
* Move common DOGM code to headers
2018-11-13 01:47:45 -06:00
Scott Lahteine
690c4e8457 Clean TLM trailing whitespace 2018-11-13 00:03:34 -06:00
Scott Lahteine
143b2896e0
Add M412 to enable/disable filament runout detection (#12406) 2018-11-12 21:29:46 -06:00
Scott Lahteine
a163c89c6a Followup to 50af1d1 2018-11-12 20:31:53 -06:00
Scott Lahteine
fea2363a2e Clear old _site contents on regeneration 2018-11-12 19:52:25 -06:00
AnHardt
be6271767f Fix BABYSTEP_ZPROBE_OFFSET (#12408)
Fix #12399

Did not compile without  `WATCH_HOTENDS || WATCH_THE_BED`.
Add condition to include "../../module/temperature.h".
2018-11-12 17:44:21 -06:00
Scott Lahteine
50af1d1e08 Differentiate translated On/Off from Serial ON/OFF 2018-11-12 17:23:08 -06:00
Scott Lahteine
df907a905f Update UBL comments for debug change 2018-11-12 03:46:48 -06:00
Scott Lahteine
da17f8ad37 For now (!) don't synchronize in M204 and M205
See if this has any deleterious effect on motion planning by slicers that inser their own jerk and acceleration controls. The problem I see is that these settings can take effect on blocks already in the planner, and the only way around this would be to shadow these settings in planner blocks and use the shadowed settings in the planner.
2018-11-12 02:43:24 -06:00
Scott Lahteine
a3923424c7 Clean up LCD width/height determination 2018-11-12 02:37:40 -06:00
Scott Lahteine
a0c795b097
Encapsulate common display code in a singleton (#12395)
* Encapsulate common LCD code in a singleton
* Depend more UBL code on UBL_DEVEL_DEBUGGING
  - Since most users don't need the debugging on at all times, this helps reduce the default build size for UBL by over 2K, a little closer to fitting on 128K boards.
2018-11-11 12:16:24 -06:00
Scott Lahteine
9da6809ac3 Adjust some comment spacing 2018-11-11 11:28:50 -06:00
Scott Lahteine
471f403a67 Reduce code size with plain inlines 2018-11-11 08:36:10 -06:00
Scott Lahteine
30a49f5ee2 Apply extra condition to LCD_PROGRESS_BAR 2018-11-11 08:36:10 -06:00
Scott Lahteine
4e0c935959 Update HAL and libs formatting 2018-11-10 19:43:23 -06:00
Scott Lahteine
47483e8c17 Update Raptor config 2018-11-10 19:42:46 -06:00
Scott Lahteine
6093df11dc
Allow G26 to use the active extruder (#12387)
* Make lcd_quick_feedback argument optional
* Add click_to_cancel option to wait_for_hotend/bed
* Have G26 use the active nozzle and wait_for_hotend/bed
* Use wait_for_release in UBL G29
* Add 'T' parameter to G26 for an initial tool-change
2018-11-10 18:07:38 -06:00
articide
4260282df7 Tevo Little Monster example configuration (#12370) 2018-11-10 03:36:01 -06:00
Scott Lahteine
bed15fcd81 Tweak 'echo_not_entered' used by MBL's G29 2018-11-10 01:32:51 -06:00
Scott Lahteine
c239131ff5 Use 'serial_spaces' in 'print_2d_array' 2018-11-10 01:32:51 -06:00
Scott Lahteine
8ab1c16ebd Break out of 'mfpub' if 'gh-pages' checkout fails 2018-11-10 01:32:51 -06:00
Scott Lahteine
56150ec030 Add reference comments to MeshLevelingState 2018-11-09 21:31:20 -06:00