Commit Graph

496 Commits

Author SHA1 Message Date
AnHardt
5b0f659355 Changes for graphics displays
Replaced displaying "---" instead of the value of a coordinate when
unhomed or with reduced precision
with blinking the coordinate-prefix-character ('X','Y','Z').
For "unhomed" a '?' is shown every second second - until that axis is
homed. The value displayed is, as before the "---" where displayed, the
relative to the reset position coordinate value.
When the axis stepper was disabled, now we can display a hint on that,
by showing a blinking ' ' instead of the axis letter, when
WARN_REDUCED_ACCURACY is defined.

I suppose the code itself is here the better documentation.

A '+/-' character is in non of our charsets so i decided for a '?' for
now to reduce the work.
There is no additional space on the displays one could use to display
the information, so replacing something is the only option. As the axis
letters are totally redundant with their positions on the display they
contain the least information.
So my decision was to overwrite them.
2016-02-28 23:19:32 +01:00
AnHardt
b6e69e71ce Make stepper shutdown after inactivity dependent
Make stepper shutdown after inactivity dependent on a new set of
#defines.
DISABLE_INACTIV_X
DISABLE_INACTIV_Y
DISABLE_INACTIV_Z
DISABLE_INACTIV_E

And make exemplaric Configuration.
Names can be discussed.

This makes the disabling of the steppers independent from the DISABLE_?
settings witch shut down the steppers immediately.
2016-02-28 16:58:42 +01:00
Scott Lahteine
b19b272172 Update configurations with SPI_SPEED
- Include aligned comment about new SDSUPPORT behavior
2016-02-17 14:54:09 -08:00
Scott Lahteine
159ff94afd Remove obsolete HEATER_BED_DUTY_CYCLE_DIVIDER #2977 2016-02-07 08:02:11 -06:00
Richard Wackerbarth
1635613c25 Backport cosmetic 2015-12-10 07:20:52 -06:00
Richard Wackerbarth
e7b40bbe98 Change link to U8glib source 2015-12-10 06:33:29 -06:00
Scott Lahteine
9b23490f01 Clean up spacing in configs 2015-11-12 00:03:21 -06:00
KiteLab
0ad25c6665 Hint for changed behaviour of SDSUPPORT 2015-09-28 11:07:33 -05:00
Richard Wackerbarth
e01f5e1ef7 Cleanup 2015-09-17 10:44:23 -05:00
Mike Cochrane
5e36b64635 SDEXTRASLOW for some SD card readers (PR#176)
Add SDEXTRASLOW which runs the SD card at SPI_QUARTER_SPEED. Quarter speed is needed for RIGIDBOT_PANEL
2015-09-14 07:58:08 -05:00
Richard Wackerbarth
20b4772155 Create DEBUG_LEVELING_FEATURE 2015-08-27 20:52:08 -05:00
Richard Wackerbarth
6292d9e815 Rename ENABLE_AUTO_BED_LEVELING
With the introduction of the #if ENABLED(…)

reads better than
2015-08-27 20:52:08 -05:00
Christian Lefrançois
9897a9147c Update ABL comments (PR#95)
* Updates the auto bed leveling comments ONLY.
* Renames "Z probe" word usage in //comments and #errors properly.
2015-08-26 05:51:38 -05:00
AnHardt
e2d69f66b2 Make Z_PROBE a Z_MIN_PROBE (PR#65)
Currently we use the probe exclusively as a device to find the build platform(bed).
For the currently supported setups this means, we use it as a additional min-endstop.
A triggered when not deployed probe disturbs the homing process for max-endstops.

Rename ENDSTOPPULLUP_ZPROBE to ENDSTOPPULLUP_ZMIN_PROBE
Rename Z_PROBE_ENDSTOP_INVERTING to Z_MIN_PROBE_ENDSTOP_INVERTING
Rename Z_PROBE_ENDSTOP to Z_MIN_PROBE_ENDSTOP
Rename DISABLE_Z_PROBE_ENDSTOP to DISABLE_Z_MIN_PROBE_ENDSTOP
Rename Z_PROBE_REPEATABILITY_TEST to Z_MIN_PROBE_REPEATABILITY_TEST
Rename Z_PROBE_ENDSTOP to Z_MIN_PROBE_ENDSTOP
Adjust comments accordingly
Remove Z_MAX  check for the probe in update_endstops().

Using an delta related idea of @clefranc from #61,
extended to the general change for all setups.

Tested with Prusa i3, max-z-endstop and permanently triggered z-probe.
Worked for @clefranc's delta.
2015-08-11 14:41:36 -05:00
Richard Wackerbarth
b227d8c128 Supply a VERSION in a short form for displays
The long descriptor will still be available in M115
2015-08-03 08:21:09 -05:00
Richard Wackerbarth
329acc852e Canonize Option flag USE_AUTOMATIC_VERSION 2015-08-03 08:08:37 -05:00
AnHardt
09571b7753 Boot-screen for the character displays
Uses about 488 byte of progmem and 32 byte of RAM.
For that configurable.
2015-08-03 07:13:00 -05:00
Scott Lahteine
1e2deff4fd Rename BTENABLED to BLUETOOTH
- For some reason it’s easy to forget what BT stands for, but it
doesn’t need an abbreviation.
2015-08-02 22:56:50 -05:00
Scott Lahteine
270c766de2 SDCARDDETECT -> SD_DETECT, added docs
- `SD_DETECT_PIN` replaces `SDCARDDETECT`
- `SD_DETECT_INVERTED` replaces `SDCARDDETECTINVERTED`
- Revise the description of `SD_DETECT_INVERTED`
- Add a note about the override of `SD_DETECT_INVERTED` in
`Conditionals.h`
2015-08-02 21:59:41 -05:00
Scott Lahteine
37d1879386 Apply overridables to Configuration files 2015-07-31 00:03:36 -05:00
Scott Lahteine
edaaead7e0 Fix comment about SERVO_ENDSTOP_ANGLES 2015-07-30 23:35:57 -05:00
Scott Lahteine
0af2a80e06 Make SERVO_ENDSTOP_ANGLES 2-dimensional 2015-07-30 16:38:56 -05:00
Richard Wackerbarth
ae00fad75b Rename as M100 2015-07-27 20:31:59 -05:00
Richard Wackerbarth
ed7d45e8f5 Memory watcher 2015-07-27 20:31:59 -05:00
AnHardt
fd0e81b0c7 Distinguish between BUZZER and SPEAKER (PR#2513)
A speaker needs a AC or a pulsed DC to make a sound, a buzzer only needs a DC.
A buzzer has it's own resonator. It works in most cases to feed the buzzer with a pulsed DC, but the sound will not be as loud as with pure DC.

There seem to be boards where the BEEPER-pin is not able to handle a PWM. Obviously intended for a buzzer.
To make these board able to handle a speaker

* replace the PWM based tone()-function again with a on-delay-off-delay loop.

Hopefully the last time I touch the beeper code.
2015-07-24 22:10:04 -05:00
AnHardt
8b876241bd Some more servo code tweaks
Just set up the pin. Don't move to a random position.

Simplify servo::move()
* servo::move() does not need the pin parameter - The pin is set during servo_init() with attach().
* servo::move() does not need a return value.

SERVO_LEVELING is the wrong condition to deactivate the servos.

Remove some temporary (Servo *) variables.
SanityCheck for the servo indexes.
2015-07-24 22:04:49 -05:00
AndySze
00dbf69b6d add MINIPANEL defines 2015-07-23 22:51:40 -05:00
AnHardt
4e14e152fa Add Travis tests for CORXY and COREXZ 2015-07-23 19:52:48 -05:00
Scott Lahteine
d85861d296 Move macros, add ENABLED/DISABLED, add includes 2015-07-22 18:16:05 -05:00
Scott Lahteine
129f986ccf Add COREXZ option to configurations 2015-07-19 16:17:03 -05:00
Scott Lahteine
391386dd94 Update configs for new servo deactivation 2015-07-15 19:13:40 -05:00
AnHardt
5243d8b523 Deactivate DEACTIVATE_SERVOS_AFTER_MOVE by default 2015-07-15 17:39:43 -05:00
AnHardt
49609f6c14 Activate the new servo.move() function
by replacing the sequences (attach, write, delay, detach), and their conditions with the new function in Marlin.main.cpp
and removing the old configuration in the ABL part of Configuration.h
2015-07-15 17:39:43 -05:00
AnHardt
40b6edcad7 Introduce DEACTIVATE_SERVOS_AFTER_MOVE in Configuration.h
DEACTIVATE_SERVOS_AFTER_MOVE is ought to replace PROBE_SERVO_DEACTIVATION_DELAY.
But it will work on all servo moves, not only the probe servo moves.
2015-07-15 17:39:43 -05:00
Scott Lahteine
c3c605c658 Move note about LiquidTWI2 to Configuration.h (PR#2406) 2015-07-09 05:33:17 -05:00
Scott Lahteine
dc40a5f6e0 Patch up more outdated config lines 2015-06-15 20:20:32 -05:00
Scott Lahteine
a274769f4f Clean up spacing and comments
Also clean up some trailing spaces in a few other sources
2015-06-15 20:20:31 -05:00
Scott Lahteine
d3bce05d54 Fix up spacing for filament sensor values 2015-06-15 20:20:31 -05:00
Scott Lahteine
b4b10a57fe Fix configurator section directives and values lists 2015-06-15 20:20:31 -05:00
Scott Lahteine
bba14dcbe6 Move Z Safe Homing point to the middle of the movement range 2015-06-15 20:20:31 -05:00
Richard Wackerbarth
58941e543e ELB_FULL_GRAPHIC_CONTROLLER_SDCARDDETECTINVERTED removed
#defining something just to define something else doesn’t
make sense

If you want SDCARDDETECTINVERTED, just define it yourself.

If the previous code was intended to define, undefined and then again define the term, that code is improper.
2015-06-06 21:44:59 -05:00
Ed Boston
b94a0e1501 Added ELB_FULL_GRAPHIC_CONTROLLER_SDCARDDETECTINVERTED
The new define allows the sd card detect to be inverted or not from
Configuration.h
2015-06-06 16:40:31 -05:00
AnHardt
d1f4471000 Merge pull request #2146 from Wackerbarth/Versioning
Versioning
2015-06-02 18:31:21 +02:00
fmalpartida
11e3f3375d Merge commit '764e61708b8e73410c7819d59c4970d7089ca6f5' into bugFixing
Updated LCD wiki location.
2015-05-31 21:20:26 +02:00
fmalpartida
93da52d011 Added support for OLED SSD1306 I2C based LCDs. 2015-05-31 18:53:29 +02:00
Jonathan Bastien-Filiatrault
e86f2342c0 Separate the maximum integral power for the bed from PID_INTEGRAL_DRIVE_MAX / PID_MAX.
My PID_INTEGRAL_DRIVE_MAX was at 96, which was insufficient for my bed
to reach its intended temperature. The head requires a low maximum power since
I run on 24 volts and it has a somewhat low thermal mass.
2015-05-28 11:48:04 -04:00
Richard Wackerbarth
5ea139fd79 Revised Versioning mechanism 2015-05-25 15:53:14 -05:00
Scott Lahteine
38cc0b93c6 Merge pull request #1874 from AnHardt/Bulgarian
Introduction of Bulgarian - language_bg.h
2015-05-22 13:59:50 -07:00
Ed Boston
152b681bb5 Added link to controller github
Added the link to the github information about the
ELB_FULL_GRAPHIC_CONTROLLER
2015-05-19 04:14:55 -07:00
AnHardt
e353d27430 Merge branch 'Development' of https://github.com/MarlinFirmware/Marlin into Bulgarian 2015-05-18 23:56:53 +02:00