646aa20b43
Overhaul of G33 Delta Calibration ( #8822 )
2018-04-11 21:14:48 -05:00
ac2e0afb62
Low Point for delta calibration ( #10363 )
2018-04-11 18:59:46 -05:00
57a899a412
[2.0.x] 6th-order jerk-controlled motion planning in real-time for AVR ( #10373 )
2018-04-11 18:13:42 -05:00
5676b187b4
Move etc/udev to buildroot/etc
...
Followup to #10375 . This is the appropriate place for any system etc folder additions.
2018-04-11 17:38:14 -05:00
44a03ecfc9
Add Linux compatibility for Arduino boards ( #10375 )
2018-04-11 14:43:28 -05:00
85014cd132
[2.0.x] LPC1768 - automatic selection of upload disk ( #10374 )
2018-04-11 14:41:16 -05:00
8669dba5e6
Merge pull request #10172 from noingwhat/2.0.x-Filament-Change-Acceleration
...
[2.0.x] Filament load/unload add acceleration for Bowden
2018-04-11 00:39:11 -05:00
472ab0cc24
Tweak RAMPS SDSS pins
2018-04-10 16:47:48 -05:00
b94c8defee
Provide additional information about SMART-RAMPS board ( #10353 )
2018-04-10 04:02:55 -05:00
6f8e228880
Add RESET_PIN to pins_RAMPS_SMART.h
2018-04-10 03:34:20 -05:00
2d9b0a66fe
Add Filament Change accelerations
2018-04-09 23:57:27 -05:00
71d3523254
Add Filament Change accelerations to example configs
2018-04-09 23:57:23 -05:00
dcb1f1f452
Merge pull request #10351 from thinkyhead/bf2_z_probe_low_point
...
[2.0.x] Z_PROBE_LOW_POINT to prevent probe/bed damage
2018-04-09 18:24:50 -05:00
8b8ad14178
Add Z_PROBE_LOW_POINT to prevent damage
2018-04-09 17:23:03 -05:00
82dafbba33
Add Z_PROBE_LOW_POINT to example configs
2018-04-09 01:55:05 -05:00
a731a723e8
Better i3-2020 Z_PROBE_OFFSET_FROM_EXTRUDER
2018-04-08 21:26:36 -05:00
26cc12eaa4
Resolve corruption of Max7219 Debug LED Matrix
2018-04-08 21:26:36 -05:00
72c15a5cc9
Add --no-track to mfnew git script
2018-04-08 06:52:29 -05:00
dca69efc11
Update Bed PID comments
2018-04-08 06:44:47 -05:00
56486c5c0e
Apply const to manage_inactivity
2018-04-08 04:00:26 -05:00
a6485456df
Fix LIGHTWEIGHT_UI with UBL
...
See https://github.com/MarlinFirmware/Marlin/issues/10317#issuecomment-379100702
2018-04-08 03:24:22 -05:00
e02fc4f1d6
Better RESTORE_LEVELING_AFTER_G28 sanity-check
...
As suggested by @GMagician
2018-04-08 03:24:15 -05:00
44a697ab04
Set STM32F1 TEMP_TIMER_FREQUENCY to 1K
...
Responding to https://github.com/MarlinFirmware/Marlin/pull/8833#issuecomment-379426803
2018-04-08 01:08:05 -05:00
cec6e19099
Add RepRapPro Huxley configuration
...
Based on #10343 by @indazoo
2018-04-08 00:37:18 -05:00
9ff4e9e1e6
Patch _IS_HW_SPI so defined() works
2018-04-07 23:29:00 -05:00
cea398849e
Tweak to gcode_line_error/return
2018-04-07 21:25:49 -05:00
4382f2124d
Merge pull request #10337 from ejtagle/bugfix-2.0.x
...
[2.0.x] 6th-order jerk-controlled motion planning in real-time
2018-04-07 21:07:59 -05:00
a29adde5c0
Implement BEZIER_JERK_CONTROL
...
Enable 6th-order jerk-controlled motion planning in real-time.
Only for 32bit MCUs. (AVR simply does not have enough processing power for this!)
2018-04-07 21:03:28 -05:00
5932df7ea1
Add BEZIER_JERK_CONTROL to example configs
2018-04-07 21:03:22 -05:00
93524c1994
Merge pull request #10045 from Lenbok/2.0.x-monitor_chamber_temperature_and_auto_fan
...
[2.0.x] Monitor chamber temperature, with auto fan control.
2018-04-06 23:52:38 -05:00
0e8242180d
Chamber temperature monitoring and auto fan control.
...
This is an initial cut for feedback, updated for 2.0.x.
Chamber temperature is currently reported along with hot end and bed
temperatures to serial. The format is just like that used for hot end
and bed temperatures, but using 'C' prefix. As there is no heater,
target is always 0. Is this appropriate, is there a better way to report
chamber temperatures?
Chamber temperatures are not reported on the LCD in any way.
When auto chamber fan is enabled, it currently just uses the same
temperature threshold as the other auto controlled fans.
As the chamber temperature is not connected to any heater, it doesn't
undergo mintemp/maxtemp monitoring. This would need to change in the
future if chamber heating became a feature.
2018-04-06 23:09:06 -05:00
5b3bda1c16
Add Chamber Temp options to example configs
2018-04-06 23:09:06 -05:00
acda4ecb20
Fix DUE Trinamic SW/HW SPI sanity check ( #10336 )
2018-04-06 22:22:30 -05:00
ab715c70d1
TMC SPI sanity-check and pins debugging ( #10324 )
2018-04-06 20:24:54 -05:00
4dc7e64789
Update Slovak language
...
Based on #10313 by @rmoravcik
2018-04-06 20:23:20 -05:00
0dccf9ea6a
Merge pull request #10318 from marcio-ao/pr-einsy-retro-tmc2130
...
[2.0.x] Fix TMC2130 DIAG1 active high, Einsy Retro
2018-04-06 20:18:34 -05:00
2efc072fdb
Clear progress bar on completion ( #10333 )
...
Fix #10330
2018-04-06 20:13:19 -05:00
6ce060cfe0
[2.0.x] Update language_it.h ( #10322 )
...
Updated to #10296
2018-04-06 20:07:46 -05:00
9356cf648f
Added support for Einsy Retro
...
http://reprap.org/wiki/EinsyRetro
2018-04-06 19:48:46 -05:00
75037493fa
Default active low for TMC2130 DIAG1 ( #10294 )
...
- Added sanity check to inform users to set the endstop to inverting
when using SENSORLESS_HOMING
2018-04-06 19:48:46 -05:00
e8e60263c8
Scale feedrate (mm/s to deg/s) for SCARA
2018-04-06 19:47:48 -05:00
051303ad42
Russian language updates
...
From #10311 by @anton-piliugin
2018-04-05 00:46:46 -05:00
386bc71d57
Merge pull request #10173 from noingwhat/2.0.x-Continuous-Purge
...
[2.0.x] Continuous Purge
2018-04-04 22:50:27 -05:00
2fa0a73c2c
Implement filament change continuous purge
2018-04-04 20:57:51 -05:00
d133ad61f3
Add continuous purge to example configs
2018-04-04 20:56:18 -05:00
4b25543633
Backtrace formatting cleanup
2018-04-04 20:24:39 -05:00
902c885782
Switch to TMC2130 compatible hardware SPI & misc ( #10299 )
2018-04-04 20:13:27 -05:00
1c36606886
Fix MSG_HEATING_FAILED_LCD_BED macro evaluation
2018-04-04 19:01:22 -05:00
fe91514395
MBL should add z_offset regardless of fade ( #10308 )
2018-04-04 18:57:33 -05:00
8bc93c6f2b
Improve heating/cooling LCD messages ( #10293 )
2018-04-04 18:29:27 -05:00
