bissen21/Marlin_Firmware
1
0
Fork 0
Code Issues Pull Requests Projects Releases 4 Wiki Activity
10,598 Commits 1 Branch 4 Tags 151 MiB
3b3029c4bf
Commit Graph

512 Commits

Author SHA1 Message Date
Andy Shaw
3b3029c4bf Make max_e_jerk an array to reduce CPU usage (#11118) 2018-06-26 22:38:31 -04:00
Giuliano
8d8f257384 [2.0.x] Fix advanced pause init values (#11095) 
Fixed for cycle used to initialize default values
 2018-06-26 14:37:52 -04:00
etagle
5b49fccf80 Add stepper driver DIR delay configuration option 
...and recommended pulse width configuration for A4988
 2018-06-26 13:28:04 -05:00
etagle
fb4e0b105b Fix endstops compilation error 2018-06-25 12:10:17 -04:00
Eduardo José Tagle
48a15d1c7e [2.0.x] Fix stepper/planner race condition and Stepper pulse timer (#11081) 
* Planner: Removal of some race conditions between Stepper ISR and Planner, some of them pointed out by @AnHardt, some of my own findings
* Fixing timing on stepper pulses adding a compensation for the non-null time required to set ports.
 2018-06-22 09:15:37 -05:00
Scott Lahteine
50b6204079 Fix LIN_ADVANCE max_e_jerk_factor 
According to https://github.com/MarlinFirmware/Marlin/issues/9917#issuecomment-399204568
 2018-06-21 22:02:34 -04:00
Scott Lahteine
99591dc20c
Filter endstops state at all times (#11066) 2018-06-21 20:14:16 -05:00
Scott Lahteine
7406f04029 Use MAX (not max) in stepper.h 2018-06-19 20:51:07 -05:00
Scott Lahteine
da94e0bd27 Unsigned eeprom mesh addresses 2018-06-15 15:51:57 -05:00
Scott Lahteine
4c8d6df13c
Extra insurance against endstop false positives (#11013) 2018-06-13 01:22:02 -05:00
Scott Lahteine
81edbfa665
Merge pull request #11004 from ejtagle/always_honor_maximum_step_rate 
[2.0.x] Fix stepper pulse minimum period and timing calculations
 2018-06-12 22:17:22 -05:00
Scott Lahteine
f3fed52348 Fix coolstep_min_speed / sensorless homing 
Fix #8890
 2018-06-12 22:12:46 -05:00
etagle
a215725df6 Fix stepper pulse timing 
Always honor minimum period on stepper pulse generation, and fix timing calculations

Signed-off-by: etagle <ejtagle@hotmail.com>
 2018-06-12 21:34:24 -05:00
Scott Lahteine
0d79128c8d Localize stepper-specific defines 2018-06-12 21:16:54 -05:00
Scott Lahteine
4dbec774b5 HAL_*_TIMER_RATE => *_TIMER_RATE 2018-06-12 16:39:12 -05:00
Scott Lahteine
9d04f47d98 Improvements for junction_deviation_mm 
- Drop `max_jerk` with `JUNCTION_DEVIATION`
- Add `max_e_jerk_factor` for use by `LIN_ADVANCE`
- Recalculate `max_e_jerk_factor` when `junction_deviation_mm` changes
- Fix LCD editing of `junction_deviation_mm`
 2018-06-11 22:05:16 -05:00
Scott Lahteine
f2c3b0d476 Use bit flags for homed/known 2018-06-11 22:05:16 -05:00
Scott Lahteine
43bdd0bfe4 Fix indent in stepper.h 2018-06-11 19:17:46 -05:00
Scott Lahteine
3fd1f32b73 Fix ADC key and chamber temp 2018-06-10 20:11:40 -05:00
Scott Lahteine
a2f521d34b
Add Junction Deviation mm runtime setting (#10990) 2018-06-10 18:02:54 -05:00
etagle
6f14bcaa3e Add MAXIMUM_STEPPER_RATE, enforce in multi-stepping 
The timing value should be properly set for ALL boards. The compiler will check and set maximum step rate calculations based on those values.
 2018-06-10 16:02:47 -05:00
etagle
39a7e7720d Adaptive multiaxis step smoothing 
- Stepper bugs fixed
- Support MIXING_EXTRUDER with Linear Advance
- Miscellaneous cleanup
 2018-06-10 16:02:47 -05:00
Giuliano
b64cc9329e [2.0.x] Fix dual enstop home (#10980) 2018-06-10 02:08:47 -05:00
Scott Lahteine
3701869e6c Add HAL_timer_start for AVR, use stepper timer to time pulses 2018-06-09 22:30:13 -05:00
etagle
d82704354f Increase the planner first block HOLD delay to 100mS 2018-06-09 21:12:37 -05:00
Scott Lahteine
334341c632
Hephestos config updates (#10960) 2018-06-07 21:23:55 -05:00
Scott Lahteine
55aedf036b Fix M503 ABL mesh report. (Zero-based IJ indices) 2018-06-07 16:36:50 -05:00
Scott Lahteine
d8b983f624
More concise M503 output for M906, M913, M914 (#10947) 2018-06-06 20:58:28 -05:00
Scott Lahteine
ad8d3150aa Cleanup for dual endstops homing 2018-06-03 00:34:29 -05:00
Eduardo José Tagle
d3c02410a8 [2.0.x] Small assorted collection of fixes and improvements (#10911) 
* Misc fixes and improvements

- Get rid of most critical sections on the Serial port drivers for AVR and DUE. Proper usage of FIFOs should allow interrupts to stay enabled without harm to queuing and dequeuing.
  Also, with 8-bit indices (for AVR) and up to 32-bit indices (for ARM), there is no need to protect reads and writes to those indices.
- Simplify the XON/XOFF logic quite a bit. Much cleaner now (both for AVR and ARM)
- Prevent a race condition (edge case) that could happen when estimating the proper value for the stepper timer (by reading it) and writing the calculated value for the time to the next ISR by disabling interrupts in those critical and small sections of the code - The problem could lead to lost steps.
- Fix dual endstops not properly homing bug (maybe).

* Set position immediately when possible
 2018-06-01 19:02:22 -05:00
Scott Lahteine
2deff0d9b9 Fix/Improve junction deviation 
- Respect axis max acceleration limits instead of forcing a fixed acceleration value.
- The `junction_unit_vec` ensures proper handling of entry and exit speeds even when the axes involved have different limits.
 2018-05-31 20:09:53 -05:00
Scott Lahteine
d259070980 Clean up trailing spaces from vim, etc. 2018-05-31 00:09:41 -05:00
Scott Lahteine
b90f54b0fc Improve probe logging 2018-05-29 21:54:13 -05:00
Scott Lahteine
4299e5dc8b
Modify E-stepping macros for use in LINEAR_ADVANCE (#10885) 2018-05-28 19:34:08 -05:00
Scott Lahteine
8f14ef855d More concise commentary in planner.cpp 2018-05-28 19:25:18 -05:00
Scott Lahteine
6919e87656 Minor cleanup of multi-stepping logic 2018-05-28 17:44:33 -05:00
Scott Lahteine
853a9056ac Long thermistor tables need special consideration 2018-05-28 06:28:34 -05:00
Scott Lahteine
a4f9c3373f Tweak thermistor spacing 2018-05-28 03:44:32 -05:00
Scott Lahteine
1ce97f1f6d
Faster (bisect) search in thermistor tables (#10883) 2018-05-27 23:27:51 -05:00
Scott Lahteine
0ca9db7051 Correct HOTENDS for SWITCHING_EXTRUDER 2018-05-27 23:22:48 -05:00
Eduardo José Tagle
7b9f0302d4 Fix Bresenham rounding errors, add link to article (#10871) 2018-05-27 01:49:59 -05:00
Scott Lahteine
2566342979 Adjust some commentary 2018-05-27 00:10:25 -05:00
Scott Lahteine
6775a16c97 Fix switching extruder stepping with LA 2018-05-26 19:07:01 -05:00
Scott Lahteine
931ab4ec40 Rename Junction Deviation options 2018-05-26 18:33:51 -05:00
Scott Lahteine
aaaf09bda2 BEZIER_JERK_CONTROL => S_CURVE_ACCELERATION 2018-05-26 18:33:51 -05:00
Scott Lahteine
01d37e00af
Fix up stepper ISR with linear advance timing (#10853) 
Co-Authored-By: ejtagle <ejtagle@hotmail.com>
 2018-05-26 01:00:13 -05:00
Scott Lahteine
7261f48872 Fix reset of endstops and move state 2018-05-24 19:33:36 -05:00
Scott Lahteine
50fa8e01c1 Minor optimization of axis_did_move bits 2018-05-24 19:08:07 -05:00
Scott Lahteine
f28e366b77 Followup for core endstops 2018-05-24 03:02:57 -05:00
Scott Lahteine
9644d56b42 Patches for core motion tests 2018-05-24 00:49:01 -05:00